Organised By :-

Total Power Solutions

Sdn. Bhd.

Where? Grand Dorsett,

Subang Jaya

When? 21st – 22nd

January 2014

At the end of this course, you will :

• Have acquired extensive exposure & knowledge on theengineering principles & design calculations for cablenetworks

• Understand how the physical properties of materials &construction will influence the operational performance ofthe cables.

• Be familiar with international standards for specification &quality control tests.

• Have acquired hands-on experience on the ins and outs ofwriting of technical specifications for power cables.Presented by:

Engr. Moh Shew Chong

ADVANCED POWER CABLE

DESIGN, SPECIFICATION &

QUALITY CONTROL TESTS

COURSE OBJECTIVE

This 2-day course is developed to provide practical training on the design & preparation oftechnical specifications for power cables up to 36kV. It gives a comprehensive coverage in thefollowing areas,

• Engineering principles & calculations on design, operation & performance of power cables

• Relating background theory to physical features & construction of power cables

• Analysis of factors that influence the current carrying rating of cable feeders, which includethermal resistivity of materials, sheath bonding techniques & method of cable laying

• Examination of relevant international standards & tests associated with the quality control &assurances of power cables

• Writing of technical specification for power cables based on system requirements & operatingenvironment

Sr. No.

4196

Who Should Attend The Course?

This course is tailored for engineers & technical staff who are involved in,

• Planning & designing of power cables networks,• Writing, validating & approving of technical specification for theprocurement of cables & accessories,

• Conducting & witnessing of quality control & factory acceptance tests(FATs),

• Supervising cable installations & commissioning of projects.

P r o f i l e o f T e c h n i c a l E x p e r tEngr. Moh Shew Chong graduated from University of Stratchclyde, Glasgow, UK, with BSc. in Electrical &

Electronic Engineering (1st Class Honour) in 1980 & was presented with the IEE Prize Award for his outstanding academic

performance. He began his engineering career at the National Electricity Board (NEB), Ipoh, followed by 7 years of service in

NEB’s training institute (ILSAS) in Bangi. As a Training Engineer, he was involved in identifying training needs, development &

conducting training courses for engineers. These courses covered design & construction of LV/HV overhead lines, aerial

bundled cables (ABC), underground cables, substation equipment, cable fault location & testing, & distribution relays &

protection.

From September 1990, Engr. Moh was transferred to the Distribution Engineering Department, in Tenaga Nasional Berhad

(TNB). He was entrusted with the task of evaluating & recommending new technologies & methodologies to further enhance the

reliability & efficiency of the distribution supply system. He had introduced several transient outage reduction techniques for

33kV overhead lines, new design of HV aerial bundled cables (ABC) to mitigate premature failures, new concept on mechanical

protection of underground cables, VLF (Very Low Frequency) testing & Partial Discharge Mapping of cables in TNB.

In March 2003, Engr. Moh was appointed as the Chief Engineer of TNB Distribution, Selangor responsible for the planning,

construction, operation & maintenance of the 33/11kV electricity supply infrastructure in Selangor. From 2005 till his retirement

in 2008, he was promoted to be the Chief Engineer (Region 1), which covers the States of Wilayah Persekutuan Kuala Lumpur,

Selangor, Putrajaya/Cyberjaya, Negeri Sembilan & Johor.

Engr. Moh had once served as the Secretary for the ASEAN Technical Working Group on Standardisation. He had also actively

participated & presented many technical papers in international conferences such as CIRED, CICED, CEPSI, AFRO-ASIAN, &

Distribution 2000 during his working career.

Advanced Power Cable Design, Specification & Quality Control Tests

DAY 1

1.1.1.1. Electrical Electrical Electrical Electrical theories on cable designtheories on cable designtheories on cable designtheories on cable design• DC, AC & insulation resistances• Skin effects & proximity effects• Electric field, inductance & Capacitance• Electrical losses• Electrical stresses & effect on interfaces• Exercises on cable design calculation

2.2.2.2. Cable Cable Cable Cable specification, specification, specification, specification, standards & standards & standards & standards & quality quality quality quality control testscontrol testscontrol testscontrol tests• Cable specification & construction• International standards on power cables• Quality control & tests

C o u r s e O u t l i n eDAY 2

3.3.3.3. Cable Cable Cable Cable accessories design, accessories design, accessories design, accessories design, standards & standards & standards & standards & quality quality quality quality control testscontrol testscontrol testscontrol tests• Joints & terminations design• International standards on cable accessories• Quality control & tests

4.4.4.4. Operating Operating Operating Operating conditions, methods of installation conditions, methods of installation conditions, methods of installation conditions, methods of installation & & & & current rating calculationcurrent rating calculationcurrent rating calculationcurrent rating calculation• Ambient conditions• Methods of laying• Thermal resistances of soil & cable materials• Cable sheath bonding• Current carrying capacity – continuous rating

& short-time rating• Exercises on calculation of thermal

resistances, continuous rating & short-time rating of power cables

5.5.5.5. Case Case Case Case studies studies studies studies & & & & exercises on writing of technical exercises on writing of technical exercises on writing of technical exercises on writing of technical specifications for power specifications for power specifications for power specifications for power cablescablescablescables

FOR REGISTRATION, PLEASE CALL (03) 2302 1525 , FAX (03) 2302 1528 or EMAIL tops@tops-sb.com

• Practical

Applications with

Working Level

Theory

• Worked Examples

• Case Studies

• Group Exercises

Course Methodology:

Please fill in the registration form &

return it with a cheque/ bank draft to

"Total Power Solutions Sdn. Bhd.”

Where : Grand Dorsett,

Subang Jaya

When : 21st - 22nd January 2014

Advanced Power Cable Design, Specification & Quality Control Tests

REGISTRATION FORM

Name: ___________________________

Position: ___________________________

Mobile No: ___________________________

Email: ___________________________

Name: ___________________________

Position: ___________________________

Mobile No : ___________________________

Email: ___________________________

Name: ___________________________

Position: ___________________________

Mobile No : ___________________________

Email: ___________________________

Company: ___________________________

Business Nature: ___________________________

Contact Person: ___________________________

Email: ___________________________

Address: ___________________________

___________________________

___________________________

Office Tel: ___________________________

Office Fax: ___________________________

Approver’s Name: ___________________________

Designation: ___________________________

Authorized Signature Company Stamp

Confirmation PolicyConfirmation of registration & training

details will be sent to you within 7 calendar

days from receipt of your registration.

Substitution of participant is allowed.

Cancellation PolicyAny cancellation must be in writing by mail,

fax or email prior to the training date subject

to the refund conditions below :-

� at least 14 calendar days notice - full

refund.

� 7 to 14 calendar days notice - a 10%

administrative fee will be imposed.

� less than 7 calendar days notice – no

refund

Training fees includes training materials,

2 coffee breaks & 1 lunch meal/buffet

per day & trainer's fee. The trainer &

topics are confirmed at the time of

publishing. TOPS reserves the right to

alter or modify the advertised

speaker/topics under circumstances

beyond the control of TOPS.

Participant’s Fees

Individual RM 2, 500 /pax

Group * RM 2, 300 /pax

* for 3 pax & above

For further enquiries : -

+6 019 330 0861 Jenny

+6 012 678 9302 Ganesh

A-15-03, Menara UOA Bangsar,

No. 5, Jalan Bangsar Utama 1,

59000 Kuala Lumpur

FOR REGISTRATION, PLEASE CALL (03) 2302 1525 , FAX (03) 2302 1528 or EMAIL tops@tops-sb.com

Sr. No. 4196