access series lcd panels - christie · 2019. 7. 30. · manufacturing facilities in canada and...

Technical Reference020-102554-06

Access Series LCD PanelsExternal Commands

NOTICESCOPYRIGHT AND TRADEMARKS

Copyright © 2019 Christie Digital Systems USA Inc. All rights reserved.

All brand names and product names are trademarks, registered trademarks or trade names of their respective holders.

GENERAL

Every effort has been made to ensure accuracy, however in some cases changes in the products or availability could occur which may not be reflected in thisdocument. Christie reserves the right to make changes to specifications at any time without notice. Performance specifications are typical, but may varydepending on conditions beyond Christie's control such as maintenance of the product in proper working conditions. Performance specifications are based oninformation available at the time of printing. Christie makes no warranty of any kind with regard to this material, including, but not limited to, impliedwarranties of fitness for a particular purpose. Christie will not be liable for errors contained herein or for incidental or consequential damages in connectionwith the performance or use of this material. Manufacturing facilities in Canada and China are ISO 9001 certified. Manufacturing facilities in Canada are alsoISO 14001 certified.

WARRANTY

Products are warranted under Christie’s standard limited warranty, the complete details of which are available by contacting your Christie dealer or Christie. Inaddition to the other limitations that may be specified in Christie’s standard limited warranty and, to the extent relevant or applicable to your product, thewarranty does not cover:

a. Problems or damage occurring during shipment, in either direction.

b. Problems or damage caused by combination of a product with non-Christie equipment, such as distribution systems, cameras, DVD players, etc., or useof a product with any non-Christie interface device.

c. Problems or damage caused by misuse, improper power source, accident, fire, flood, lightning, earthquake, or other natural disaster.

d. Problems or damage caused by improper installation/alignment, or by equipment modification, if by other than Christie service personnel or a Christieauthorized repair service provider.

e. Use of third party product enclosures for environmental protection during outside use must be approved by Christie.

f. Problems or damage caused by use of a product on a motion platform or other movable device where such product has not been designed, modified orapproved by Christie for such use.

g. Except where the product is designed for outdoor use, problems or damage caused by use of the product outdoors unless such product is protected fromprecipitation or other adverse weather or environmental conditions and the ambient temperature is within the recommended ambient temperature setforth in the specifications for such product.

h. Image retention on LCD flat panels.

i. Defects caused by normal wear and tear or otherwise due to normal aging of a product.

The warranty does not apply to any product where the serial number has been removed or obliterated. The warranty also does not apply to any product soldby a reseller to an end user outside of the country where the reseller is located unless (i) Christie has an office in the country where the end user is located or(ii) the required international warranty fee has been paid.

The warranty does not obligate Christie to provide any on site warranty service at the product site location.

PREVENTATIVE MAINTENANCE

Preventative maintenance is an important part of the continued and proper operation of your product. Failure to perform maintenance as required, and inaccordance with the maintenance schedule specified by Christie, will void the warranty.

REGULATORY

The product has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designedto provide reasonable protection against harmful interference when the product is operated in a commercial environment. The product generates, uses, andcan radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radiocommunications. Operation of the product in a residential area is likely to cause harmful interference in which case the user will be required to correct theinterference at the user’s own expense.

CAN ICES-3 (A) / NMB-3 (A)

이 기기는 업무용(A급)으로 전자파적합등록을 한 기기이오니 판매자 또는 사용자는 이점을 주의하시기 바라며, 가정 외의 지역에서 사용하는 것을 목적으로 합니다.

ENVIRONMENTAL

The product is designed and manufactured with high-quality materials and components that can be recycled and reused. This symbol means that electrical

and electronic equipment, at their end-of-life, should be disposed of separately from regular waste. Please dispose of the product appropriately and accordingto local regulations. In the European Union, there are separate collection systems for used electrical and electronic products. Please help us to conserve theenvironment we live in!

ContentIntroduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

RS232 communication parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Connecting to the RS232 port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Setting up terminal programs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Setting up the Ethernet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Product documentation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Related documentation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

RS232 commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10AUTOPOS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

CHANGELNG. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

COLOURTEMP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

CONTRASTDOWN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

CONTRASTUP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

DOTCLOCK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

get_IP_address. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

GETAVL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

GETBALANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

GETBRIGHTNESS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

GETCOLOUR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

GETCOLOURTEMP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

GETCONTRAST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

GETCOUNTRY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

GETDEFAULTGATEWAY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

GETDIGITALOUT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

GETDNS1 and GETDNS2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

GETDOTCLOCK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

GETDYNAMICBASS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

GETENERGYSAVING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

GETEQUSERFREQ. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

GETEQMODE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

GETFREESPACE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

GETHEADPHONEOUTPUT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

GETHEADPHONEVOLUME. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Access Series LCD Panels Technical Reference–External Commands 3020-102554-06 Rev. 1 (11-2018)Copyright © 2019 Christie Digital Systems USA, Inc. All rights reserved.

GETHPOS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

GETLED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

GETMENUTIMEOUT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

GETMODELNO. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

GETMUTE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

GETNETWORKTYPE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

GETOPSPOWER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

GETOSDORIENTATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

GETPICTUREMODE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

GETPOWERONDELAY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

GETPOWERSAVE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

GETQUICKSTANDBY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

GETRC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

GETSCHEDULEOP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

GETSCHEDULER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

GETSERIALNO. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

GETSHARPNESS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

GETSLIDESHOWINTERVAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

GETSOURCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

GETSTANDBY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

GETSWVERSION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

GETSUBNETMASK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

GETTOTALSPACE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

GETUSBAUTOPLAY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

GETVIEWSTYLE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

GETTVLIFETIME. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

GETVOLUME. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

GETVPOS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

GWOL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

HEADPHONEVOLUME. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

HPOS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

KEY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

MENUTIMEOUT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

PICTUREMODE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

PICTUREZOOM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

RESET. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

RST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

SAVEMODELINFO. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

SELECTSOURCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Content


set_IP_address. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

SETAVL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

SETBALANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

SETBRIGHTNESS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

SETCOLOUR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

SETCONTRAST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

SETCOUNTRY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

SETDEFAULTGATEWAY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

SETDIGITALOUT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

SETDYNAMICBASS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

SETEQUSERFREQ. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

SETEQMODE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

SETHEADPHONEOUTPUT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

SETMUTE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

SETNETWORKTYPE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

SETOPSPOWER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

SETPOWERONDELAY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

SETQUICKSTANDBY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

SETRC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

SETSCHEDULEOP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

SETSCHEDULER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

SETSHARPNESS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

SETSLIDESHOWINTERVAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

SETSOUNDMODE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53

SETSOURCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

SETSUBNETMASK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

SETUSBAUTOPLAY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

SETVIEWSTYLE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

SIGNAGERESET. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

SOUNDRESET. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

STANDBY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56

STARTFTI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

STEA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

STV. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

STWA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

SWOL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58

TIME. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

UNP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

VOLUMEDOWN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Content


VOLUMEUP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

VPOS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

WAKEUP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Content


IntroductionThis document provides information and procedures for using serial commands (ASCII text messages)to control the product.

RS232 communication parametersThe RS232 IN port has several communication parameters.

Parameter Value

Default baud rate 115200

Parity None

Data bits 8

Stop bits 1

Flow control None

When the baud rate is set to 38400, the panel remains at that baud rate when in an ON and OFFstate. When the baud rate is set to 115200, it returns to baud rate 38400 when it is in an OFF state.To use the Wake on RS232 command, the connection to the display panel must be configured with38400 baud rate.To change the baud rate, on the panel select Signage Settings > Controls > UART0 > ASCII andselect the baud rate.

Connecting to the RS232 portUse an RS232 connection to remotely access display controls and image setups, issue commands orqueries, and receive replies.

1. Connect one end of a straight through DB9 connector serial RS232 cable to the display panelRS232 port.

2. Connect the other end of the cable to a computer.

Setting up terminal programsLearn how to configure terminal programs for proper echoing.

When using any terminal program other than PuTTy, you must include a carriage return (\r) and a linefeed (\n) after all API commands.

Configure the settings for your terminal program.

• TeraTerm


a. Select Setup > TCP/IP and set:

• Host: IP address

• TCP port#: 1986

• Telnet: checked

b. Select Setup > Terminal and set:

• Local echo: checked

• Transmit: CR+LF

• HyperTermSelect File > Properties > ASCII setup and set:

• Send line ends with line feeds: checked

• Echo typed characters locally: checked

• TCPSelect File > Properties > ASCII setup and set:

• Host: IP address

• Telnet: unchecked

• TCP port#: 1986

Setting up the EthernetTo use Ethernet, the LAN (Standby) setting of the projector must be enabled and the display panelmust be in Standby mode.

1. Download the Wake On LAN (WOL) software.Free Wake On LAN software packages are available for downloading from the internet. Thesteps below are for the Aquilia WOL software.

2. To open WakeOnLAN, select the downloaded file and click New Host.

3. Select the Wake Up page.a) Enter the MAC address, which is the same as the display panel.

b) Enter the broadcast IP address.The domain is the same as the computer.For example, the IP address of the computer is 10.0.21.105, the subnet mask is255.255.0.0, and the broadcast IP address is set to 10.0.255.255.

4. Enter any IP address in the FQDN/IP.Leave all other fields at their default values.

5. Select the newly added host, right-click, and select Wake Up.

Product documentationFor installation, setup, and user information, see the product documentation available on the Christiewebsite. Read all instructions before using or servicing this product.

1. Access the documentation from the Christie website:

Introduction


• Go to this URL:http://bit.ly/2iUdjFs.

• Scan the QR code using a QR code reader app on a smartphone or tablet.

2. On the product page, select the model and switch to the Downloads tab.

Related documentationAdditional information on the LCD panels is available in the following documents.

• Access Series LCD Panels Product Safety Guide (P/N: 020-102422-XX)

• Access Series LCD Panels Installation and Setup Guide (P/N: 020-102404-XX)

• Installing the Touch Overlay (P/N: 020-102431-XX)

• UHD551-L Service Guide (P/N: 020-102683-XX)

• UHD651-L Service Guide (P/N: 020-102685-XX)

• UHD751-P Service Guide (P/N: 020-102686-XX)

• UHD861-P Service Guide (P/N: 020-102744-XX)

Introduction


http://bit.ly/2iUdjFs

RS232 commandsThe UHD Display Panels commands can be used to modify product settings.

When using any terminal program other than PuTTy, you must include a carriage return (\r) and a linefeed (\n) after all API commands.

VGA/PC commands Picture commands Network commands

GETHPOS (on page 24)

HPOS (on page 37)

GETCOLOURTEMP (on page 17)

COLOURTEMP (on page 14)

get_IP_address (on page 15)

set_IP_address (on page 41)

GETVPOS (on page 35)

VPOS (on page 61)

GETPICTUREMODE (on page 28)

PICTUREMODE (on page 38)

GETNETWORKTYPE (on page 26)

SETNETWORKTYPE (on page 48)

GETDOTCLOCK (on page 20)

DOTCLOCK (on page 15)

GETCONTRAST (on page 18)

SETCONTRAST (on page 43)

GETSUBNETMASK (on page 33)

SETSUBNETMASK (on page 54)

AUTOPOS (on page 12) GETBRIGHTNESS (on page 17)

SETBRIGHTNESS (on page 43)

GETDEFAULTGATEWAY (on page19)

SETDEFAULTGATEWAY (on page44)

GETOSDORIENTATION (on page27)

GETSHARPNESS (on page 31)

SETSHARPNESS (on page 52)

GETDNS1 and GETDNS2 (on page20)

GETOPSPOWER (on page 27)

SETOPSPOWER (on page 48)

GETCOLOUR (on page 17)

SETCOLOUR (on page 43)

PICTUREZOOM (on page 39)

CONTRASTUP (on page 15)

CONTRASTDOWN (on page 14)

GETENERGYSAVING (on page 21)

GETPOWERSAVE (on page 28)

WAKEUP (on page 61)

Admin panel commands Signage settings commands Media Browser commands

RST (on page 40) GETTOTALSPACE (on page 33) GETVIEWSTYLE (on page 34)

SETVIEWSTYLE (on page 55)STV (on page 58) GETFREESPACE (on page 23)

STWA (on page 58) GETSCHEDULER (on page 30)

SETSCHEDULER (on page 51)

GETUSBAUTOPLAY (on page 34)

SETUSBAUTOPLAY (on page 55)STEA (on page 57)

UNP (on page 59) GETSCHEDULEOP (on page 30)

SETSCHEDULEOP (on page 50)

GETSLIDESHOWINTERVAL (on page31)

SAVEMODELINFO (on page 40)


Admin panel commands Signage settings commands Media Browser commands

SETSLIDESHOWINTERVAL (on page52)

Audio commands General display commands

GETVOLUME (on page 35) GETRC (on page 29)

SETRC (on page 50)

GETHEADPHONEVOLUME (on page 24)

HEADPHONEVOLUME (on page 36)

GETSOURCE (on page 32)

SETSOURCE (on page 53)

SELECTSOURCE (on page 40)

GETMUTE (on page 26)

SETMUTE (on page 47)

GETCOUNTRY (on page 18)

SETCOUNTRY (on page 44)

SOUNDRESET (on page 56) GETSWVERSION (on page 33)

SETSOUNDMODE (on page 53) KEY (on page 37)

GETBALANCE (on page 16)

SETBALANCE (on page 42)

RESET (on page 39)

CHANGELNG (on page 12)

GETAVL (on page 16)

SETAVL (on page 42)

GETSTANDBY (on page 32)

STANDBY (on page 56)

GETDYNAMICBASS (on page 21)

SETDYNAMICBASS (on page 45)

GETMENUTIMEOUT (on page 25)

MENUTIMEOUT (on page 38)

GETEQUSERFREQ (on page 22)

SETEQUSERFREQ (on page 46)

GETMODELNO (on page 25)

GETSERIALNO (on page 31)

GETDIGITALOUT (on page 19)

SETDIGITALOUT (on page 45)

GETLED (on page 24)

GETEQMODE (on page 22)

SETEQMODE (on page 46)

GETQUICKSTANDBY (on page 29)

SETQUICKSTANDBY (on page 49)

VOLUMEUP (on page 60)

VOLUMEDOWN (on page 60)

SIGNAGERESET (on page 56)

GETHEADPHONEOUTPUT (on page 23)

SETHEADPHONEOUTPUT (on page 47)

GETTVLIFETIME (on page 35)

TIME (on page 59)

GETPOWERONDELAY (on page 28)

SETPOWERONDELAY (on page 49)

STARTFTI (on page 57)

RS232 commands


AUTOPOSAutomatically position the image on the display panel.

Commands

Command Description Values

AUTOPOS Automatically positions the image on thedisplay panel.

—

Examples

Automatically position the image on the display panel.

AUTOPOSResult:

#*set auto position

CHANGELNGChange the language used in a specific area of the display panel.

Commands


CHANGELNG <area><language>

Changes the language used in a specificarea of the display panel.

Area

• 0 = System Language

• 1 = Event Language

• 2 = Primary Audio Language

• 3 = Secondary Audio Language

• 4 = Primary Subtitle Language

• 5 = Secondary Subtitle Language

• 6 = Primary Teletext Language

• 7 = Secondary Teletext Language

Language

• 0 = Danish

• 1 = German

• 2 = Estonian

• 3 = English

• 4 = Spanish

• 5 = Greek

RS232 commands



• 6 = French

• 7 = Gaelic

• 8 = Croatian

• 9 = Italian

• 10 = Latvian

• 11 = Lithuanian

• 12 = Hungarian

• 13 = Dutch

• 14 = Norwegian

• 15 = Polish

• 16 = Portuguese

• 17 = Russian

• 18 = Romanian

• 19 = Albanian

• 20 = Slovenian

• 21 = Slovak

• 22 = Serbian

• 23 = Finnish

• 24 = Swedish

• 25 = Turkish

• 26 = Czech

• 27 = Ukranian

• 28 = Bulgarian

• 29 = Arabic

• 30 = Persian

• 31 = Hebrew

• 32 = Belarussian

• 33 = Macedonian

• 34 = Montenegrin

• 35 = Kazakh

• 36 = Thai

Examples

Change the system language to French.

CHANGELNG 0 6Result:

RS232 commands


#*Active language was changed

COLOURTEMPSet the color temperature.

Commands


COLOURTEMP<value>

Sets the color temperature. • normal

• warm

• cool

Examples

Set the color temperature to cool.

COLOURTEMP coolResult:

#*setColourTemp() set to cool

CONTRASTDOWNDecrease the contrast level by one step.

Commands


CONTRASTDOWN Decreases the contrast level by one step. —

Examples

Decrease the contrast level by one step.

CONTRASTDOWNResult:

#*Picture contrast value is set to 5

RS232 commands


CONTRASTUPIncrease the contrast level by one step.

Commands


CONTRASTUP Increases the contrast level by one step. —

Examples

Increase the contrast level by one step.

CONTRASTUPResult:


DOTCLOCKSet the dot clock.

Commands


DOTCLOCK Set the dot clock. -50 to 50

Examples

Set the dot clock to 12.

DOTCLOCK 12Result:

#*set dot clock to 12

get_IP_addressDisplay the IP address of the eth0 network interface.

Commands


get_IP_address Displays the IP address of the eth0 networkinterface.

—

RS232 commands


Examples

Display the IP address of the eth0 network interface.

get_IP_address

GETAVLDisplays the current AVL setting.

Commands


GETAVL Displays the state of AVL. • 0 = Off

• 1 = On

Examples

Display the AVL state.

GETAVLResult:

#*avl state is 0

GETBALANCEDisplays the current balance setting.

Commands


GETBALANCE Gets the balance value —

Examples

Display the balance value.

GETBALANCEResult:

#*balance level is -20

RS232 commands


GETBRIGHTNESSDisplay the current brightness setting.

Commands


GETBRIGHTNESS Displays the current brightness setting. —

Examples

Display the current brightness setting.

GETBRIGHTNESSResult:

#*Picture brightness value is set to 25

GETCOLOURDisplay the picture color setting.

Commands


GETCOLOUR Displays the picture color setting. —

Examples

Display the picture color setting.

GETCOLOURResult:

#*The colour value : 43

GETCOLOURTEMPDisplay the current color temperature setting.

Commands


GETCOLOURTEMP Display the current color temperaturesetting.

—

RS232 commands


Examples

Display the current color temperature setting.

GETCOLOURTEMPResult:

#*Colour temp is warm

GETCONTRASTDisplay the picture contrast setting.

Commands


GETCONTRAST Display the picture contrast setting. —

Examples

Display the picture contrast setting.

GETCONTRASTResult:

#*THE CONTRAST VALUE : 25

GETCOUNTRYDisplay the current country setting.

Commands


GETCOUNTRY Displays the country setting. —

Examples

Display the currently configured country.

GETCOUNTRYResult:

#*COUNTRY IS : Canada

RS232 commands


GETDEFAULTGATEWAYDisplay the current default gateway.

Commands


GETDEFAULTGATEWAY

Displays the current default gateway. —

Examples

Display the current default gateway.

GETDEFAULTGATEWAYResult:

#*the default gateway is 10.1.1.3

GETDIGITALOUTDisplay the current digital out setting.

Commands


GETDIGITALOUT Get digital out state. —

Examples

Display the status of digital out.

GETDIGITALOUTResult:

#*digital out is pcmor

#*digital out is compressed

RS232 commands


GETDNS1 and GETDNS2Display the DNS of server 1 or server 2.

Commands


GETDNS1 Display the DNS of server 1. —

GETDNS2 Display the DNS of server 2. —

Examples

Display the DNS of server 1.

GETDNS1Result:

#*DNS server 1 is 10.10.10.10

GETDOTCLOCKDisplay the current dot clock settings.

Commands


GETDOTCLOCK Displays the current dot clock settings. —

Examples

Displays the current dot clock settings.

GETDOTCLOCKResult:

#*The dot clock is 12

RS232 commands


GETDYNAMICBASSDisplays the current dynamic bass setting.

Commands


GETDYNAMICBASS Displays the dynamic bass set. • 0 = Off

• 1 = On

Examples

Display the current dynamic bass set.

GETDYNAMICBASSResult:

#*The dynamic bass state is 0.

GETENERGYSAVINGDisplay the current energy saving mode.

Commands


GETENERGYSAVING Displays the current energy saving mode. —

Examples

Display the current energy saving mode.

GETENERGYSAVINGResult:

#*The energy saving mode is on

RS232 commands


GETEQUSERFREQDisplay the equalizer setting for a specific band.

Commands


GETEQUSERFREQ<band>

Displays the equalizer setting for a specificband.

-12 to 12

Examples

Display the equalizer setting for 120Hz.

GETEQUSERFREQ 120HzResult:

#*the equalizer value for the band is 10

GETEQMODEDisplays the current equalizer mode setting.

Commands


GETEQMODE Get the equalizer mode. • Music

• Movie

• Speech

• Flat

• Classic

• User

Examples

Display the equalizer mode.

GETEQMODEResult:

#*the equalizer mode is Movie

RS232 commands


GETFREESPACEDisplay the amount of free space on the connected USB device.

Commands


GETFREESPACE Displays the amount of space on theconnected USB device, in mb.

—

Examples

Display the amount of free space on the connected USB device.

GETFREESPACEResult:

#*The total space is 480 MB

GETHEADPHONEOUTPUTDisplay the current headphone setting.

Commands


GETHEADPHONEOUTPUT

Display the headphone status. —

Examples

Display the headphone status.

GETHEADPHONEOUTPUTResult:

#*LINEOUTor

#*HEADPHONE

RS232 commands


GETHEADPHONEVOLUMEDisplays the volume level of the headphones.

Commands


GETHEADPHONEVOLUME

Headphone volume level information —

Examples

Display the volume level of the headphones.

GETHEADPHONEVOLUMEResult:

#*headphone volume level is 7

GETHPOSDisplay the current horizontal position.

Commands


GETHPOS Displays the current horizontal position. —

Examples

Display the current horizontal position.

GETHPOSResult:

#*The horizontal position is -10

GETLEDDisplay the current status of the LED.

Commands


GETLED Displays the status of the LED. —

RS232 commands


Examples

Display the current status of the LED.

GETLEDResult:

#*LED is on

GETMENUTIMEOUTDisplay the current menu timeout settings.

Commands


GETMENUTIMEOUT Displays the current menu timeout settings. —

Examples

Display the current menu timeout settings.

GETMENUTIMEOUTResult:

#*menu timeout mode is 15or

#*menu timeout mode is OFF

GETMODELNODisplay the model number of the display panel.

Commands


GETMODELNO Displays the model number of the displaypanel.

—

Examples

Display the model number of the display panel.

GETMODELNO

RS232 commands


GETMUTEDisplays the current mute setting.

Commands


GETMUTE Retrieves the status of mute. —

Examples

Display the status of mute.

GETMUTEResult:

#*MUTE OFFor

#*MUTE ON

GETNETWORKTYPEDisplay the network type setting.

Commands


GETNETWORKTYPE Display the network type setting. —

Examples

Display the network type setting.

GETNETWORKTYPEResult:

#*the network type is wired

RS232 commands


GETOPSPOWERDisplays the current power state of the OPS.

Commands


GETOPSPOWER Displays the current power state of the OPS. —

Examples

Display the power status of the OPS.

GETOPSPOWERResult:

#*The OPS is not plugged inor

#*The OPS is onor

#*The OPS is off

GETOSDORIENTATIONDisplay the orientation of the on-screen display.

Commands


GETOSDORIENTATION

Displays the orientation of the on-screendisplay.

—

Examples

Display the orientation of the on-screen display.

GETOSDORIENTATIONResult:

#*The OSD orientation landscape

RS232 commands


GETPICTUREMODEDisplay the current picture mode setting.

Commands


GETPICTUREMODE Displays the current picture mode setting. —

Examples

Display the current picture mode setting.

GETPICTUREMODEResult:

#*Picture Mode is 3

GETPOWERONDELAYDisplay the current power on delay setting.

Commands


GETPOWERONDELAY Displays the current power on delay setting. —

Examples

Display the current power on delay setting.

GETPOWERONDELAYResult:

#*The power on delay is 1200 ms

GETPOWERSAVEDisplay the current power saving mode.

Commands


GETPOWERSAVE Displays the current power saving mode. —

RS232 commands


Examples

Display the current power saving mode.

GETPOWERSAVEResult:

#*Powersavemode is ON

GETQUICKSTANDBYDisplay the current state of quick standby.

Commands


GETQUICKSTANDBY Display the current state ofSETQUICKSTANDBY.

—

Examples

Displays the current state of quick standby.

GETQUICKSTANDBYResult:

#*Quick Standby is off.

GETRCDisplay the current status of the remote control.

Commands


GETRC Displays the status of the remote control. —

Examples

Display the current status of the remote control.

GETRCResult:

#*remote control commands are on

RS232 commands


GETSCHEDULEOPDisplay the scheduler parameters.

Commands


GETSCHEDULEOP<preset>

Displays the scheduler parameters for thespecified preset.

Preset = 1, 2, 3, or 4

Examples

Display the scheduler parameters for preset 1.

GETSCHEDULEOP 1Result:

#*Scheduler: 1 - Active: 1 - Source: 12 - OFF Enabled: 1ON: 31/07/2017 10:30:00 - OFF: 01/08/2017 03:30:00DAYS: MON TUE WED THU FRI SAT SUN

GETSCHEDULERDisplay the status of the scheduler.

Commands


GETSCHEDULER<preset>

Displays the status of the scheduler for thespecified preset.

Preset = 1, 2, 3, or 4

Examples

Display the status of the scheduler.

GETSCHEDULER 1Result:

#*The scheduler is ON

RS232 commands


GETSERIALNODisplay the serial number of the display panel.

Commands


GETSERIALNO Displays the serial number of the displaypanel.

—

Examples

Display the serial number of the display panel.

GETSERIALNO

GETSHARPNESSDisplay the picture sharpness setting.

Commands


GETSHARPNESS Display the picture sharpness setting. —

Examples

Display the picture sharpness setting.

GETSHARPNESSResult:

#*THE SHARPNESS VALUE : 30

GETSLIDESHOWINTERVALDisplay the current slide show interval setting.

Commands


GETSLIDESHOWINTERVAL

Displays the current slide show intervalsetting.

—

RS232 commands


Examples

Display the current slide show interval setting.

GETSLIDESHOWINTERVALResult:

#*The slideshow interval is 30 seconds

GETSOURCEDisplay the currently enabled source.

Commands


GETSOURCE Displays the current source. —

Examples

Display the current source.

GETSOURCEResult:

#*source is VGA

GETSTANDBYDisplay the current standby status.

Commands


GETSTANDBY Displays the current standby status. —

Examples

Display the current standby status.

GETSTANDBYResult:

#*standby onor

#*standby off

RS232 commands


GETSWVERSIONDisplay the version of software installed on the display panel.

Commands


GETSWVERSION Displays the version of software installed onthe display panel.

—

Examples

Display the version of software installed on the display panel.

GETSWVERSIONResult:

#*V <version number>

GETSUBNETMASKDisplay the subnet mask.

Commands


GETSUBNETMASK Displays the subnet mask. —

Examples

Display the subnet mask.

GETSUBNETMASKResult:

#*the subnet mask is 255.255.255.0

GETTOTALSPACEDisplay the total amount of space on the connected USB device.

Commands


GETTOTALSPACE Displays the amount of space on theconnected USB device, in mb.

—

RS232 commands


Examples

Display the amount of space on the connected USB device.

GETTOTALSPACEResult:

#*The total space is 4096 MB

GETUSBAUTOPLAYDisplay the current USB autoplay setting.

Commands


GETUSBAUTOPLAY Displays the current USB autoplay setting. —

Examples

Display the current USB autoplay setting.

GETUSBAUTOPLAYResult:

#*The USB autoplay is ON

GETVIEWSTYLEDisplay the current view style for the Media Browser.

Commands


GETVIEWSTYLE Displays the current view style for the MediaBrowser.

—

Examples

Display the current view style for the Media Browser.

GETVIEWSTYLEResult:

#*The view style is flat

RS232 commands


GETTVLIFETIMEDisplay the number of minutes the display panel has been on.

Commands


GETTVLIFETIME Display the number of minutes the displaypanel has been on.

—

Examples

Display the number of minutes the display panel has been on.

GETTVLIFETIMEResult:

#*Monitor Life Time: n

GETVOLUMEDisplays the volume level of the display panel.

Commands


GETVOLUME Volume level information —

Examples

Display the volume level of the display panel.

GETVOLUMEResult:

#*volume level is 7

GETVPOSDisplay the current vertical position.

Commands


GETVPOS Displays the current vertical position. —

RS232 commands


Examples

Display the current vertical position.

GETVPOSResult:

#*The vertical position is -10

GWOLDisplays the status of Wake on LAN.

Commands


GWOL Displays the status of Wake on LAN. —

Examples

Displays the status of Wake on LAN.

GWOL

HEADPHONEVOLUMESets the headphone volume.

Commands


HEADPHONEVOLUME Sets the headphone volume level. 0 to 100

Examples

Set the headphone volume to 20.

HEADPHONEVOLUME 20Result:

#*set headphone volume to 20

RS232 commands


HPOSSet the horizontal position.

Commands


HPOS <value> Sets the horizontal position of the image onthe display panel. The value is a percentageof image.

-25 to 25

Examples

Set the horizontal position to -10.

HPOS -10Result:

#*set horizontal position to -10

KEYNavigate the display panel menu as if using the remote control.

Commands


KEY <value> Sends a key command the display panelmenu, as if the key was pressed on theremote control.

The value can be a number, direction, ormenu item.

For a list of the available values, at theprompt type KEY + or KEY ?

Examples

Display the menu.

KEY menuIncrease the volume by one step.

KEY vol+Play the media.

KEY play

RS232 commands


MENUTIMEOUTSet the amount of time before the menu times out.

Commands


MENUTIMEOUT<time>

Sets the amount of time before the menutimes out.

• 0 = Off

• 15 = 15 seconds

• 30 = 30 seconds

• 60 = 60 seconds

Examples

Set the menu to time out after 30 seconds.

MENUTIMEOUT 30Result:

#*set menu timeout mode to 30

PICTUREMODESet the picture mode.

Commands


PICTUREMODE<mode>

Sets the picture mode. • 1 = Dynamic

• 2 = Natural

• 3 = Cinema

• 4 = Game

• 5 = Sport

Examples

Set the picture mode to cinema.

PICTUREMODE 3Result:

#*setPictureMode() set to 3

RS232 commands


PICTUREZOOMSet the zoom mode.

Commands


PICTUREZOOM<mode>

Sets the zoom mode. • auto

• 16:9

• subtitle

• 14:9

• 14:9zoom

• 4:3

• full (only for HD channels)

• cinema

Examples

Set the zoom mode to 16:9.

PICTUREZOOM 16:9Result:

#*setPictureZoomMode() set to 16:9

RESETReset the display panel.

Commands


RESET Resets the device. —

Examples

Reset the display panel.

RESET

RS232 commands


RSTRestart the display panel.

Commands


RST Restarts the display panel. —

Examples

Restart the display panel.

RSTResult:

#*Monitor will be restarted

SAVEMODELINFOSave the model name and software version of the display panel to a removable device.

Commands


SAVEMODELINFO Saves the model name and software versionof the display panel to the connected device.

—

Examples

Save the model name and software version of the display panel to the connected device.

SAVEMODELINFOResult:

#*Model info is saved

SELECTSOURCESet the video source.

Commands


SELECTSOURCE<source>

Sets the video source. • 5=BACK AV

RS232 commands



• 7=HDMI1

• 8=HDMI2

• 11=YPbPr

• 12=VGA

• 18=DVI

• 19=DP

• 20=OPS

Examples

Set the video source to DisplayPort.

SELECTSOURCE 19Result:

#*select 19 source

set_IP_addressSet the static IP address of the eth0 network interface.

Commands


set_IP_address <IPaddress>

Set the static IP address of the eth0network interface.

—

Examples

Set the static IP address of the eth0 network interface to 198.168.0.15.

set_IP_address 198.168.0.15Result:

#*IP address setting Successful

RS232 commands


SETAVLTurn AVL on and off.

Commands


SETAVL <value> Turns AVL on or off. 0 = Off

1 = On

Examples

Turn off AVL.

SETAVL 0Result:

#*set avl state to 0

SETBALANCESets the audio balance.

Commands


SETBALANCE Set balance value. -50 to 50

Examples

Set balance to -20.

SETBALANCE -20Result:

#*set balance level to -20or

#*Invalid balance level entered

RS232 commands


SETBRIGHTNESSSet the picture brightness.

Commands


SETBRIGHTNESS<value>

Sets the picture brightness. 0 to 100

Examples

Set the picture brightness to 40.

SETBRIGHTNESS 40Result:

#*Picture brightness value is set to 40

SETCOLOURSet the picture color.

Commands


SETCOLOUR <value> Sets the picture color. 0 to 100

Examples

Set the picture color to 43.

SETCOLOUR 43Result:

#*Picture colour value is set to 43

SETCONTRASTSet the picture contrast.

Commands


SETCONTRAST<value>

Sets the picture contrast. 0 to 100

RS232 commands


Examples

Set the picture contrast to 25.

SETCONTRAST 25Result:


SETCOUNTRYChange the country setting.

Commands


SETCOUNTRY<country>

Set the country. —

Examples

Change the country to Germany.

SETCOUNTRY GermanyResult:

#* setCountry() set to Germany

SETDEFAULTGATEWAYSet the default gateway.

Commands


SETDEFAULTGATEWAY Set the default gateway for the networkconnection, formatted as xxx.xxx.xxx.xxx.

—

Examples

Set the default gateway to 10.1.1.3.

SETDEFAULTGATEWAY 10.1.1.3Result:

#*set default gateway: 10.1.1.3

RS232 commands


SETDIGITALOUTSet digital out to compressed or PCM.

Commands


SETDIGITALOUT<mode>

Set digital out. • compressed

• pcm

Examples

Set digital out to PCM

SETDIGITALOUT pcmResult:

#*setDigitalOut() set to pcm

SETDYNAMICBASSTurns mute on and off.

Commands


SETDYNAMICBASS Turns the dynamic base on or off. • 0 = Off

• 1 = On

Examples

Turn on the dynamic bass.

SETDYNAMICBASS 1Result:

#*set dynamic bass state to 1

RS232 commands


SETEQUSERFREQSet the equalizer setting for any band.

Commands


SETEQUSERFREQ<band> <equalizersetting>

Sets the equalizer setting for one of thefollowing bands:

• 120Hz

• 500Hz

• 1.5KHz

• 5KHz

• 10KHz

-12 to 12

Examples

Set the setting to 10 for the 120Hz band.

SETEQUSERFREQ 120Hz 10Result:

#*setEQUserFreq() set to nor

#*Incorrect sound system parameter enteredor

#*Incorrect equalizer mode. It should be USER mode

SETEQMODESet the equalizer mode.

Commands


SETEQMODE<mode>

Set the equalizer mode. • Music

• Movie

• Speech

• Flat

• Classic

• User

RS232 commands


Examples

Set the equalizer mode to Movie.

SETEQMODE MovieResult:

#*setEQMode() set to Movie

SETHEADPHONEOUTPUTSet the headphone output.

Commands


SETHEADPHONEOUTPUT <output>

Sets the headphone output. • headphone

• lineout

Examples

Set the headphone out put to lineout.

SETHEADPHONEOUTPUT lineoutResult:

#*set headphone output to lineout

SETMUTETurns mute on and off.

Commands


SETMUTE Sets the mute value to on or off. —

Examples

Change the mute value to the opposite of the current value. If mute is currently enabled, it will be disabled.

SETMUTEResult:

#*MUTE OFFor

#*MUTE ON

RS232 commands


SETNETWORKTYPESet the network as wired, wireless, or disabled.

Commands


SETNETWORKTYPE<type>

Set the network type. • wired

• wireless

• disabled

Examples

Set the network type as wired.

SETNETWORKTYPE wiredResult:

#*Network type is set to: wired

SETOPSPOWERTurn the OPS power on and off.

Commands


SETOPSPOWER Turns the OPS power on and off. • on

• off

Examples

Turn on the OPS power.

SETOPSPOWER onResult:

#*Turning OPS on

RS232 commands


SETPOWERONDELAYSet how long the display waits before powering on.

Commands


SETPOWERONDELAY<delay>

Sets how long the display waits beforepowering on. The delay is calculated as(100ms * <delay>).

0 to 20

Examples

Set the power on delay to 12.

SETPOWERDELAY 12Result:

Power on delay set to 1200 Ms.

SETQUICKSTANDBYTurn quick standby on or off.

In the on-screen display, System > Settings > More > Quick Standby must be enabled for thiscommand to function.

Commands


SETQUICKSTANDBY<value>

Turns quick standby on or off. value:

• on

• off

Examples

Turn quick standby off.

SETQUICKSTANDBY offResult:

#*Set Quick Standby off

RS232 commands


SETRCEnable and disable the remote control.

Commands


SETRC <value> Enables and disables remote controlcommands.

• ON

• OFF

Examples

Disable the remote control.

SETRC OFFResult:

#*set remote state OFF

SETSCHEDULEOPSet the schedule for the display panel.

Commands


SETSCHEDULEOP <preset>_<on-enabled>_<on_time>_<off-enabled>_<off_time>_<day of theweek>_<source>

Set the schedule for the displaypanel.

<Preset> = 1, 2, 3, or 4

<on-enabled> and <off-enabled>:

• 0 = Disabled

• 1 = Enabled

<on_time> and <off_time> areformatted as hh:mm.

<day of the week> = each digitin the sequence is one day of theweek, starting with Sunday.

• 0 = Schedule does notapply

• 1 = Schedule applies

<source>:

• LastSource

• USB

• DP

RS232 commands



• OPS

• DVI

• HDMI

• YPBPR

• VGA/PC

Examples

Set the preset 4 to turn on at 6:30am and off at 11:30pm on Monday, Wednesday, and Friday, for VGA/PC.

SETSCHEDULEOP 4_1_06:30_1_23:30_0101010_VGA/PCResult:

#*Schedule parameters are setSet the preset 2 to turn on at 8:00am and off at 6:00pm on Monday to Friday, for USB.

SETSCHEDULEOP 2_1_08:00_1_18:00_0111110_USBResult:

#*Schedule parameters are set

SETSCHEDULEREnable and disable the scheduler.

Commands


SETSCHEDULER<preset> <ON |OFF>

Enable and disable the scheduler for thespecified preset.

Preset = 1, 2, 3, or 4

Examples

Enable the scheduler.

SETSCHEDULER 1 ONResult:

#*The scheduler for preset 1 is set to ON

RS232 commands


SETSHARPNESSSet the picture sharpness.

Commands


SETSHARPNESS<value>

Set the picture sharpness. 0 to 100

Examples

Set the picture sharpness to 27.

SETSHARPNESS 27Result:

#*Picture sharpness value is set to 27

SETSLIDESHOWINTERVALSet the slide show interval, in seconds.

Commands


SETSLIDESHOWINTERVAL <seconds>

Set the slide show interval, in seconds. • 5

• 10

• 15

• 20

• 25

• 30

Examples

Set the slide show interval to 20 seconds.

SETSLIDESHOWINTERVAL 20Result:

#*The slideshow interval is set to 20 seconds

RS232 commands


SETSOUNDMODESets the sound mode.

Commands


SETSOUNDMODE<mode>

Sets the sound mode. • 0 = Mono

• 1 = Stereo

• 2 = Dual I

• 3 = Dual II

• 4 = Mono left

• 5 = Mono right

Examples

Set the sound mode to stereo.

SETSOUNDMODE 1Result:

#*setSoundMode() set to 1or

#*Invalid sound mode entered

SETSOURCEEnable and disable sources.

Commands


SETSOURCE<source> <state>

Enables and disables sources. Source:

• SCART1

• SCART2

• FAV

• SVHS

• HDMI1

• HDMI2

• HDMI3

• HDMI4

RS232 commands



• YPBPR

• VGA

• SCART1S

• SCART2S

State:

• 0 = Disable

• 1 = Enable

Examples

Disable VGA.

SETSOURCE VGA 0Result:

#*Selected source VGA#*Enable/Disable state : b

SETSUBNETMASKSet the subnet mask for the network connection.

Commands


SETSUBNETMASK<subnet mask>

Sets the subnet mask for the networkconnection, formatted as xxx.xxx.xxx.xxx.

—

Examples

Set the subnet mask as 255.255.255.0.

SETSUBNETMASK 255.255.255.0Result:

#*set subnet mask: 255.255.255.0

RS232 commands


SETUSBAUTOPLAYTurn USB autoplay on and off.

Commands


SETUSBAUTOPLAY<value>

Turns USB autoplay on and off. • ON

• OFF

Examples

Turn USB autoplay on.

SETUSBAUTOPLAY ONResult:

#*The USB autoplay is set to ON

SETVIEWSTYLESet whether the Media Browser displays content in a flat list or in folders.

Commands


SETVIEWSTYLE<view>

Set whether the Media Browser displayscontent in a flat list or in folders.

• Flat

• Folder

Examples

Display Media Browser content in folders.

SETVIEWSTYLE FolderResult:

#*The view style is set to folder

RS232 commands


SIGNAGERESETSet all items in the Signage Settings menu to the default values.

Commands


SIGNAGERESET Sets all items in the Signage Settings menuto the default values.

—

Examples

Set all items in the Signage Settings menu to the default values.

SIGNAGERESETResult:

#*All signage settings set to default values

SOUNDRESETReset all sounds settings to the default.

Commands


SOUNDRESET Resets all sounds to the default. —

Examples

Reset all sound settings to the default.

SOUNDRESET

STANDBYSet the display panel to Standby mode.

Commands


STANDBY Switches the display panel to Standby.

To wake the panel from standby, run theWakeup command.

—

RS232 commands


Examples

Put the display panel into standby mode.

STANDBY

Related information

WAKEUP (on page 61)

STARTFTIStart the first time installation wizard.

Commands


STARTFTI Starts the first time installation wizard. —

Examples

Start the first time installation wizard.

STARTFTIResult:

#*FTI was initialising

STEAStop the emergency alarm.

Commands


STEA Stop the emergency alarm. —

Examples

Stop the emergency alarm.

STEAResult:

#Emergency Alarm is stopped !!!

RS232 commands


STVSet the display panel volume.

Commands


STV <value> Set the display panel volume. 0 to 100

Examples

Set the display panel volume to 55.

STV 55Result:

#*Volume set level= 55

STWAStop the wake alarm.

Commands


STWA Stops the wake alarm. —

Examples

Stop the wake alarm.

STWAResult:

#*WakeupAlarm stopped !!!

SWOLEnable and disable the Wake on LAN feature.

Commands


SWOL <value> Enable and disable the Wake on LANfeature.

• 0 = Disable

• 1 = Enable

RS232 commands


Examples

Disable the Wake on LAN feature.

SWOL 0

TIMEDisplay the current date and time.

Commands


TIME Display the current date and time. —

Examples

Display the current date and time.

TIME

UNPSend a message

Commands


UNP <message> Send a message. Message content should be formatted as"word1+word2+word3..."

Examples

Send message with the text "This is a message."

UNP "This+is+a+message."Result:

#*Message Sent in SUCCESS !!!

RS232 commands


VOLUMEDOWNTurn down the volume.

Commands


VOLUMEDOWN Decreases the volume by one, until theminimum volume is reached.

—

Examples

Turn down the volume.

VOLUMEDOWNResult:

#*volume LEVEL is decreased to <level>

VOLUMEUPTurn up the volume.

Commands


VOLUMEUP Increases the volume by one, until themaximum volume is reached.

—

Examples

Turn up the volume.

VOLUMEUPResult:

#*volume LEVEL is increased to <level>

RS232 commands


VPOSSet the vertical position.

Commands


VPOS <value> Sets the vertical position of the image onthe display panel.

-25 to 25

Examples

Set the vertical position to -10.

VPOS -10Result:

#*set horizontal position to -10

WAKEUPWake the display panel from standby.

This command requires that the terminal program be set to baud rate 38400.

Commands


WAKEUP Wakes the display panel. —

Examples

Wake the display panel.

WAKEUP

Related information

STANDBY (on page 56)

RS232 commands


For the most current technical documentation, visit www.christiedigital.com.

Christie Digital Systems Canada Inc.Kitchenerph: 519 744 8005

Christie Digital Systems USA, Inc.Cypressph: 714 236 8610

Corporate offi ces

United Kingdomph: +44 (0) 118 977 8000

United Arab Emiratesph: +971 4 3206688

Spainph: +34 91 633 9990

Singaporeph: +65 6877 8737

Republic of South Africaph: +27 (0)11 510 0094

Korea (Seoul)ph: +82 2 702 1601

Japan (Tokyo)ph: 81 3 3599 7481

Indiaph: +91 (080) 6708 9999

Germanyph: +49 2161 664540

Franceph: +33 (0) 1 41 21 44 04

Russian Federationand Eastern Europeph: +36 (0) 1 47 48 100

China (Shanghai)ph: +86 21 6278 7708

China (Beijing)ph: +86 10 6561 0240

Brazilph: +55 (11) 2548 4753

Australiaph: +61 (0) 7 3624 4888

Worldwide offi ces

Italyph: +39 (0) 2 9902 1161

Independant sales consultant offi ces

Mexicoph: +52 55 4744 1790

United States (New York)ph: 646 779 2014

United States (Arizona)ph: 602 943 5700

access series lcd panels - christie · 2019. 7. 30. · manufacturing facilities in canada and...

Documents