access motor co., ltd.ax700-ul%e7%b3… · 1. trade name or mark of the device : access 2....

Access Motor Co., Ltd. No. 5, Chung-Hsin Rd., Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi Hsien 612, Taiwan Tel: 886-5-2377870 Fax: 886-5-2377875

APPLICATION FOR EXTENSION APPROVAL OF TWO OR THREE-WHEEL MOTOR VEHICLES

ACCORDING TO 2002/24/EC DIRECTIVE AMENDED BY 2013/60/EU

1. Trade name or mark of the Device

: Access

2. Manufacturer’s name of the Device

: AX700-UL

3. Manufacturer’s name and address :

Access Motor Co., Ltd. No. 5, Chung-Hsin Rd., Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi Hsien 612, Taiwan

4. If applicable, name and address of manufacturer’s representative

: Not applicable

5. Brief description

: Quadricycle

6. Submitted for approval on (date)

: July 16, 2014

We herewith certify that we didn’t apply nor receive a certificate for the above mentioned type in any other EC/ECE member state.

Name: Sean Huang Position: General Manager Date: July 16, 2014

THIS APPLICATION IS ACCOMPANIED WITH:

-The test report


CERTIFICATE OF CONFORMITY CERTIFICATE OF CONFORMITY ACCOMPANYING EACH VEHICLE IN THE SERIES OF THE

TYPE WHICH HAS BEEN APPROVED The undersigned:

_______________ hereby certifies that the following vehicle:

0.1. Make: Access

0.2. Type: AX700-UL Variant: N.A. Version: N.A.

0.2.1. Commercial name(s): Access Motor, as option: SS250R, Hammel, Quadzilla, Bogart Patriot, Nexmotor, Tomahawk, Apollo, Spike, Speed, Maverick, TKM, FOCUS, TENA, TRITON, MAX, APACHE, Burelli, Warrior, GOES

0.4. Vehicle category: L7e

0.4.1. Vehicle category according to Directive 97/24/EC, Chapter 7: N.A.

0.5. Name and address of the manufacturer: Access Motor Co., Ltd. No. 5, Chung-Hsin Rd., Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi Hsien 612, Taiwan

0.6. Location of the statutory plate: R, x1120, y128, z680 Vehicle identification number: RK3AX36204A000001

0.7. Location of the vehicle identification number on the chassis: R, x60, y90, z305

Conforms in all respects to the type described in EC type-approval - EC type-approval number: e4*2002/24*3058*01 - Dated: The vehicle can be permanently registered without requiring any further approvals, for driving on the right/left and for using metric/imperial units for the speedometer.

Chia-Yi, Taiwan, R.O.C. (Place) (Date)

(Signature) (Position)

Additional Information

1. Number of axles: 2 and wheels: 4

3. Wheel base: 1440 mm

6.1. Length: 2250 mm

7.1. Width: 1200 mm

8. Height: 1495 mm 12.1. Mass of the vehicle (with bodywork) in running order: 362 kg 12.2. Unladen mass of the vehicle: 348 kg 14.1. Technically permissible maximum laden mass: 542 kg

14.2. Distribution of this mass among the axles: 1. 249 kg 2. 293 kg

14.3. Technically permissible mass on each axle: 1. 249 kg 2. 293 kg

17. Maximum mass of trailer:

(brake): 174 kg (unbraked): ..............kg

19.1. Maximum vertical load at the coupling point for a trailer: 35 kg

20. Engine manufacturer: Access Motor Co., Ltd.

21. Engine type as marked on the engine: E20

21.2. Engine number: E20R??????

22. Working principle: electric/spark ignition/compression ignition, four/two stroke

23. Number and arrangement of cylinders: S

24. Cylinder capacity: 686 cm3

25. Fuel: P

26. Maximum net power or maximum continuous rated power as applicable: 10.80 kW at 4400 min-1

26.1. Ratio: maximum net power or maximum continuous rated power/mass of the vehicle in running order: 0.030 kW/kg

28. Gearbox (type): A

29. Gear ratio:

CVT GEARBOX Final Drive

Minimum Maximum FORWARD REVERSE L gear H gear

1: 1.378 1: 0.654 1: 5.044 1: 2.989 1: 5.206 1: 3.667

32. Tyre size designation: Axle 1: AT25x8-12 Axle 2: AT25x10-12 37. Body: No

41. Number and configuration of doors: N.A.

42.1. Number and position of seats: 2, r1: 1C, r2: 1C

43.1. Approval mark of coupling device, if fitted: e4*97/24*97/24/10*3026*00

44. Maximum speed: 60 km/h

45. Sound level: In accordance with 97/24/EC Chapter 9, amendment 2009/108/EC Stationary: 85 dB(A) at engine speed: 3300 min-1 Drive-by: 80 dB(A)

46. Exhaust emissions: In accordance with 97/24/EC Chapter 5, amendment 2009/108/EC, stage 2003

46.1. Euro level: 2 46.2. Type I test: CO: 0.805 g/km, HC: 0.049 g/km, NOx: 0.101 g/km, HC+NOx: -- 46.3. Type II test: for motorcycles and tricycles: CO: 1.11 % Visible air pollution caused by an engine with compression ignition: N.A. corrected value of absorption coefficient: N.A.

47. Fiscal power or national code number(s):

Italy: France: Spain: Belgium: Germany: Luxembourg: Denmark: Netherlands: Greece: United Kingdom: Irland: Portugal: Austria: Sweden: Finland: Czech Republic: Estonia: Cyprus: Latvia: Lithuania: Hungary: Malta: Poland: Slovenia: Slovakia: Romania: Bulgaria:

50. Remarks:

51. Exemptions:

Vehicle Technology Division

P.O. Box 777 Tel. + 31 (0)79 345 81 43 Vehicle Admission & Surveillance 2700 AT Zoetermeer Fax + 31 (0)79 345 80 43 The Netherlands www.rdw.nl WVTA 2002.24-2013.60 v6.00 Page 1 of 4

THE NETHERLANDS (N E D E R L A N D)

EC TYPE-APPROVAL CERTIFICATE

Communication concerning:

- type-approval (1) - extension of type-approval (1) - refusal of type-approval (1) - withdrawal of type-approval (1)

of a type of vehicle with regard to Directive 2002/24/EC. EC type-approval number : e4*2002/24*3058*01

Reason for extension : - addition of optional commercial name “GOES”

- addition of optional front, rear brake caliper(s) and master cylinder

- addition of coupling device and the attachment - deletion of optional trade mark “Goes”

0. General

0.1. Make(s) (trade name of the

manufacturer) : Access

0.2. Type Variant(s) Version(s)

: : :

AX700-UL Not applicable Not applicable

0.2.1. Commercial name(s) : Access Motor, as option: SS250R, Hammel, Quadzilla, Bogart Patriot, Nexmotor, Tomahawk, Apollo, Spike, Speed, Maverick, TKM ,FOCUS , TENA , TRITON , MAX, APACHE, Burelli, Warrior, GOES

0.3. Means of identification of type, if marked on the vehicle

: ???AX3???????????

0.3.1. Location of that marking

: On the right side of frame body

Type-approval number: e4*2002/24*3058*01

WVTA 2002.24-2013.60 v6.00 Page 2 of 4

0.4. Category (2) : L7e

0.5. Name and address of the vehicle manufacturer

: Access Motor Co., Ltd. No. 5, Chung-Hsin Rd., Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi Hsien 612, Taiwan

0.5.1. Name(s) and address(es) of assembly plant(s)


The undersigned hereby certifies the accuracy of the manufacturer’s description in the attached information document of the vehicle type described above, for which one or several representative samples, selected by the competent approval authorities, has (have) been submitted as prototype(s) of the vehicle type and that the attached test results are applicable to the vehicle type.

The vehicle type meets/does not meet (1) the technical requirements of all relevant separate Directives (as last amended) listed in the table of Annex I to Directive 2002/24/EC.

The approval is granted/refused/withdrawn (1).

Place : Zoetermeer

Signature :

Date :

Attachments: – – –

–

Information document, Parts 1 and 2 (Annex II). Test results (Annex VII). Name(s) and specimen(s) of the signature of the persons authorised to sign the certificates of conformity and a statement of their position in the company. A model certificate of conformity.

(1) Delete where not applicable. (2) According to the classification introduced in Article 1.

24-SEP-2014

vecht

Sign-stamp-name


WVTA 2002.24-2013.60 v6.00 Page 3 of 4

ANNEX VII

TEST RESULTS

(Article 5(1), first subparagraph)

In each case, the information must make clear to which variant and version it is applicable. One version may not have more than one result. 1. Results of the sound level tests.

Number of the base Directive and latest amending Directive applicable to the approval.

In the case of a Directive with two or more implementation stages, indicate also the implementation stage:

- 97/24/EC Chapter 9 as last amended by 2009/108/EC

Variant/version Not applicable/ Not applicable --

Moving dB(A) 80 --

Stationary dB(A) 85 --

at (min-1) 3300 --

2. Results of the exhaust emission tests.

Number of the base Directive and latest amending Directive applicable to the approval.

In the case of a Directive with two or more implementation stages, indicate also the implementation stage:

- 97/24/EC Chapter 5 as last amended by 2009/108/EC, stage A (2003)

Variant/version Not applicable/ Not applicable --

Euro level (1) Euro 2 --

2.1. Type I

CO (g/km) 0.805 --

HC (g/km) (1) 0.049 --

NOx (g/km) (1) 0.101 --

HC + NOx (g/km) (2) -- --

CO2 (g/km) (2) -- --

Fuel consumption (l/100 km) (2)

-- --

2.2. Type II

CO (g/min) (2) -- --

HC (g/min) (2) -- --

CO (% vol) at normal idle speed (1)

1.11 --

Specify the idle speed (1) (3)

1600±100 --

CO (% vol) at high idle speed (1)

1.25 --


WVTA 2002.24-2013.60 v6.00 Page 4 of 4

Specify the idle speed (1) (3)

2800±100 --

Engine oil temperature (1) (4)

88 °C at 1660 min-1

89 °C at 2880 min-1

--

3. Compression ignition engine

Variant/version -- --

Corrected value of absorption coefficient (m-1)

-- --

(1) See footnote 12 in Annex IV. (2) Only for L1e, L2e and L6e category vehicles. (3) For L-category vehicles within the scope of Article 1 of Directive 2002/24/EC with the exception of L1e, L2e and L6e vehicles. (4) Mention the measurement tolerance. (5) Applicable for four-stroke engines only.

TÜV Rheinland Group

Test Report No.: 84-2002/24-00793/14-00

Type : Manufacturer :

AX700-UL Access Motor Co., Ltd.

Typprüfstelle Fahrzeuge/Fahrzeugteile Engineering Centre Shanghai Master_RDW_en_R13 Page 1 of 21 TÜV Rheinland Kraftfahrt GmbH TÜV Rheinland (Shanghai) Co., Ltd. 77-793e14-00.rdw

Am Grauen Stein, 51105 Cologne, Germany No. 177, 179, 189, Lane 777, Designation: RDW-99050014-06 West Guangzhong Road, Shanghai, P.R. China

T E S T R E P O R T

According to Council Directive on the approximation of the laws of the Member States relating to the

Type-approval

of two or three-wheel motor vehicles

No.: 2002/24/EC

as last amended by

No.: 2013/60/EU

Approval Status

EC type – approval : e4*2002/24*3058*01

Structure of report: Item No. 0. General information 1. Tested vehicle(s) 2. Test record 3. List of appendices 4. Statement of conformity The Test Report shall be reproduced and published in full by the client only. It shall however be reproduced partially with the written permission of the Testing Laboratory only.


Test Report No.: 84-2002/24-00793/14-00





0. General information

0.1. Make (trade name of the

manufacturer) : Access

0.2. Type : AX700-UL

0.3. Category of vehicle : L7e

0.4. Name and address of the manufacturer


0.5. No. of information document date of issue date of last amendment

: : :

AX700-UL-2002/24-01 January 14, 2014 July 16, 2014


Test Report No.: 84-2002/24-00793/14-00





1. Tested vehicle(s)

1.1. Description

1.1.1 Vehicle : Quadricycle

Commercial description : Access Motor

Type / variant(s) / version(s) : AX700-UL / Not applicable / Not applicable

Identification number : RK3AX36204A000003

1.1.2 Condition of vehicle(s) : Used

1.2. Worst case selection : The determination of worst case scenario was done according QMA 1.301.005, section 6.2.2.2.

1.3. Remarks : All versions of the vehicle type as stated in the information folder are covered by the tested vehicle version(s) respectively.


Test Report No.: 84-2002/24-00793/14-00





2. Test record

2.1. Equipment for measuring and

testing : The test facilities / measurement equipment used were in

compliance with the test requirements.

2.1.1 Specifications for the test site : Not applicable

2.1.2 Subcontracting : Not applicable

2.2. Test results : See Appendix 1

Remarks concerning extension : The vehicle type has been tested according to the modification(s) mentioned in appendix 0.

The new parts meet the requirements of the Directives.

An actual practical test of the vehicle was not necessary. The results of the previous test(s) are still valid.

2.2.1 Measurements : All measurement results are listed and referred to the respective limit(s) with judgment.

2.2.2 Alternative test provisions : Not applicable

2.2.3 Attributive tests : Not applicable

2.3. Additional information : The results of the test refer exclusively to the object(s) mentioned under point 1.1. of this report.

Test site : Lu-Kang / Taiwan

Test date : January 20 to May 14, 2014

2.4. Remarks : --


Test Report No.: 84-2002/24-00793/14-00





3. List of Appendices

0 List of modifications

1 Test minutes of the frame directive

: Pages 8 to 16

2 Test minutes of braking system : Pages 17 to 20

3 Test minutes of audible warning device

: Not attached as not relevant to the extension

4 Test minutes of protective device : Not attached as not relevant to the extension

5 Test minutes of mass and dimension


6 Test minutes of maximum speed : Not attached as not relevant to the extension

7 Test minutes of maximum engine power and torque


8 Test minutes of tyre installation : Not attached as not relevant to the extension

9 Test minutes of external projection


10 Test minutes of rear-view mirror(s) installation


11 Test minutes of anti-pollution devices


12 Test minutes of fitting of fuel tank


13 Test minutes of anti-tampering measures

: Not attached as not applicable to the vehicle category

14 Test minutes of EMC : Not attached as not relevant to the extension

15 Test minutes of noise measuring : Not attached as not relevant to the extension

16 Test minutes of speedometer : Not attached as not relevant to the extension


Test Report No.: 84-2002/24-00793/14-00





17 Test minutes of rear registration plate


18 Test minutes of lighting installation


19 Test minutes of stands : Not attached as not applicable to the vehicle category

20 Test minutes of hand hold : Not attached as not applicable to the vehicle category

21 Test minutes of identification of controls, tell-tales and indicators


22 Test minutes of statutory marking


23 Test minutes of coupling devices attachment

: Page 21

24 Information folder no. (excluding drawings)

: AX700-UL-2002/24-01 (20 pages)

4. Statement of conformity

The above mentioned information folder and the type described in that comply with the requirements mentioned on page 1. With regard to the required level of performance to be achieved, the tested items were representative for the type to be approved (see point 1.2.). The mentioned test results refer to the vehicle(s) described under point 1.1. of this report.

Shanghai, 2014/07/29 KWU/JYW

Expert Technical Service


Test Report No.: 84-2002/24-00793/14-00





List of modifications Appendix 0

Correction of : --

Modification of : --

Addition of : - optional commercial name “GOES” - optional front, rear brake caliper(s) and master cylinder - coupling device and the attachment

Deletion of : - optional trade mark “Goes”


Test Report No.: 84-2002/24-00793/14-00





Test minutes of the frame directive Appendix 1

1. General

1.1. Make : Access


Variant(s) : Not applicable

Version(s) : Not applicable

1.3. Name and address of manufacturer : Access Motor Co., Ltd. No. 5, Chung-Hsin Rd., Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi Hsien 612, Taiwan

1.4. Name and address of manufacturer’s authorized representative

: Not applicable

2. General arrangement of vehicle

2.1. Category of vehicle : L7e

2.2. Maximum design speed : 60 km/h (@ H gear) According to SD 95/1/EC, amendment 2006/27/EC

Conformity checks : Requirements fulfilled, for test results see appendix 6

Approval number : Not applicable

2.3. Wheels

2.3.1 Number : 4

2.3.2 Symmetrical or asymmetrical configuration

: Symmetrical

2.4. Frame layout diagram : See drawing No. 71000-A36-H00

3. Masses and dimensions : According to SD 93/93/EEC, amendment 2004/86/EC


Test Report No.: 84-2002/24-00793/14-00







3.1. Mass of vehicle in running order : See Information Document AX700-UL-2002/24-01, 2.1.

3.1.1 Distribution of that mass between the axles

: See Information Document AX700-UL-2002/24-01, 2.1.1.

3.2. Mass of vehicle in running order together with rider

: See Information Document AX700-UL-2002/24-01, 2.2.

3.2.1 Distribution of that mass between the axles


3.3. Maximum technically permissible mass declared by the manufacturer

: See Information Document AX700-UL-2002/24-01, 2.3.

3.3.1 Division of that mass between the axles


3.3.2 Maximum technically permissible mass on the axles


3.4. Vehicle length : 2250 mm

3.5. Vehicle width : 1200 mm

3.6. Vehicle height : 1495 mm

4. Engine

4.1. Manufacturer of engine : See Information Document AX700-UL-2002/24-01, 3.0.

4.2. Make : See Information Document AX700-UL-2002/24-01, 3.1.

4.3. Type : E20

4.4. Spark- or compression-ignition engine : Spark-ignition / compression ignition engine


Test Report No.: 84-2002/24-00793/14-00





4.4.1 Operating cycle : See Information Document AX700-UL-2002/24-01, 3.2.1.1.

4.4.2 Cooling system : See Information Document AX700-UL-2002/24-01, 3.2.7.

4.4.3 Lubrication system : Pressure circulation wet-sump system

4.4.4 Number, arrangement and firing order of cylinders

: See Information Document AX700-UL-2002/24-01, 3.2.1.2.

4.4.5 Bore, stroke and cylinder capacity : See Information Document AX700-UL-2002/24-01, 3.2.1.2.1. - 3.2.1.3.

4.4.6 Full drawing of induction system : See Information Document AX700-UL-2002/24-01, 3.2.8.3.

4.4.7 Compression ratio : See Information Document AX700-UL-2002/24-01, 3.2.1.4.

4.4.8 Maximum net power and maximum net torque

: See Information Document AX700-UL-2002/24-01, 3.2.1.7. - 3.2.1.8., according to SD 95/1/EC, amendment 2006/27/EC



4.4.9 Fuel tank : According to SD 97/24/EC Chapter 6, amendment 2006/120/EC See Information Document AX700-UL-2002/24-01, 3.2.3.

Conformity checks : Requirements fulfilled, for test results see appendix 12; fuel tank report No. 84-97/2406-00603/11

Approval number (installation) : Not applicable

Approval number (component) : See Information Document AX700-UL-2002/24-01, 3.2.3.4.

4.4.10 Fuel supply : See Information Document AX700-UL-2002/24-01, 3.2.4.


Test Report No.: 84-2002/24-00793/14-00





10.15 Anti-tampering measures for mopeds and motorcycles

: Not applicable

Conformity checks : Not applicable


4.4.11 Electrical system : See Information Document AX700-UL-2002/24-01, 3.2.5.

4.4.12 Generator : See Information Document AX700-UL-2002/24-01, 3.2.5.2.

10.3. Electromagnetic compatibility : According to SD 97/24/EC Chapter 8, amendment 2006/120/EC see Information Document AX700-UL-2002/24-01, 3.2.6.8.



10.4. Sound level and exhaust system : According to SD 97/24/EC Chapter 9, amendment 2009/108/EC



10.4.1 Make of exhaust system : See Information Document AX700-UL-2002/24-01, 3.2.9.

10.4.2 Type of exhaust system : One main muffler

10.4.3 Sound level

Stationary noise, dB(A) at min-1 : 85 / 3300

Noise when in motion in dB(A) : 80

4.4.13 Anti-pollution devices : According to SD 97/24/EC Chapter 5, amendment 2009/108/EC


Test Report No.: 84-2002/24-00793/14-00







4.5. Electric traction motor : Not applicable

5. Transmission

Type : Manual / automatic

2.2. Maximum design speed : According to SD 95/1/EC, amendment 2006/27/EC, see Information Document AX700-UL-2002/24-01, 4.6.



10.12. Speedometer : According to SD 2000/7/EC, see Information Document AX700-UL-2002/24-01, 4.7



6. Tyres : According to SD 97/24/EC Chapter 1, amendment 2006/120/EC see Information Document AX700-UL-2002/24-01, 5.2.



Tyres of any tyre manufacturer may be fitted provided that they are of the same dimensions, E/e-mark approved according to ECE-R75 or 97/24/EC, chapter 1 and of a load index of 36 (front tyres) / 42 (rear tyres) or more and a speed index of F (all tyres) or more.


Test Report No.: 84-2002/24-00793/14-00





7. Braking system : According to SD 93/14/EEC, amendment 2006/27/EC, see Information Document AX700-UL-2002/24-01, 7.



8. Installation of lighting and light-signalling devices

: According to SD 2009/67/EC, See Information Document AX700-UL-2002/24-01, 8.2.



9. Lighting and light-signalling devices : According to SD 97/24/EC Chapter 2, amendment 2006/120/EC, see Information Document AX700-UL-2002/24-01, 8.1.

Conformity checks : Requirements fulfilled

Approval number : See Information Document AX700-UL-2002/24-01, 8.1.

10. Miscellaneous

10.16. Coupling devices and their attachment : According to SD 97/24/EC Chapter 10, amendment 2006/120/EC see Information Document AX700-UL-2002/24-01, 9.1.


Approval number : e4*97/24*97/24/10*3026*00

10.13. Identification of controls, tell-tales and indicators

: According to SD 2009/80/EC, see Information Document AX700-UL-2002/24-01, 9.2.


Test Report No.: 84-2002/24-00793/14-00







10.14. Statutory inscriptions : According to 2009/139/EC, see Information Document AX700-UL-2002/24-01, 9.3.



Location of statutory plate : on the right side of rear frame body

10.8. Devices to prevent unauthorized use : According to SD 93/33/EEC, amendment 1999/23/EC, see Information Document AX700-UL-2002/24-01, 9.4.



10.1. Audible warning device : According to SD 93/30/EEC, see Information Document AX700-UL-2002/24-01, 9.5.


Approval number, annex II (installation)

: Not applicable

Approval number, annex I (component)


10.2. Location of rear registration plate : According to SD 2009/62/EC, see Information Document AX700-UL-2002/24-01, 9.6.



Test Report No.: 84-2002/24-00793/14-00






10.6. External projections : According to SD 97/24/EC Chapter 3, amendment 2006/120/EC



B. Information relating solely to two-wheel mopeds and motorcycles

Not applicable


Test Report No.: 84-2002/24-00793/14-00





C. Information relating solely to three-wheel mopeds, motorcycles and quadricycles

10.9. Windows : Without (vehicle without bodywork)

10.5. Rear-view mirrors : According to SD 97/24/EC Chapter 4, amendment 2006/120/EC See Information Document AX700-UL-2002/24-01, C 2.6.


Approval number (installation) : Not applicable

Approval number (component) : See Information Document AX700-UL-2002/24-01, C 2.6.2.

10.11. Anchorages for safety belts : Without (vehicle without bodywork)


Test Report No.: 84-2002/24-00793/14-00





Test minutes of braking system Appendix 2

0. Test condition

0.1. Test date : January 20 to 21, 2014

0.2. Test site : Lu-Kang / Taiwan

1. Test facilities : The test equipment used was in compliance with the Requirements of the directive.

2. Test object(s)

2.1. Type

: AX700-UL

Variant

: Not applicable

Version : Not applicable

2.2. Identification number : RK3AX36204A000003

2.3. Technically permissible mass on axles

Axle 1 [kg]

: 249

Axle 2 [kg] : 293

2.4. Load conditions of the vehicle during the test

Unladen Laden

Axle 1 [kg] 237 217

Axle 2 [kg] 212 327

Total [kg] 449 544

2.5. Number and arrangement of the axles : 2 axles


Test Report No.: 84-2002/24-00793/14-00





2.6. Brief description of the service braking device

: One foot-controlled combined system acting on the all wheels. One supplementary hand-controlled left hand lever acting on the rear axle. One supplementary hand-controlled right hand lever acting on the front axle.

Combined (service brake) : Foot pedal, foot operated, mechanical and hydraulic transfer, disc brakes.

Manufacturer of the brake system : Access Motor Co., Ltd.

Manufacturer of brake pads : Yun Chen Tech. Motor Co., Ltd.

Front (secondary brake) : Right hand lever, manually operated, mechanical and hydraulic transfer, disk brakes


Manufacturer of brake pad : Yun Chen Tech. Motor Co., Ltd.

Rear (secondary brake) : Left hand lever, manually operated, mechanical and hydraulic transfer, disc brakes


Manufacturer of brake pad : Yun Chen Tech. Motor Co., Ltd.

2.7. Other devices (anti-lock, etc..) : Parking brake device: Independent hand lever, purely mechanical device acting on the rear axle.


Test Report No.: 84-2002/24-00793/14-00





3. Test results

3.1. Type-0 test, with engine disconnected / automatic transmission under normal driving condition

Conditions Test speed

Measured performance

Measured force applied to control

(km/h) (m/s2) (N) Unladen, dry brakes

Combined service brake 54 5.7 281

Secondary brake axle 1 54 6.1 180


Laden, dry brakes




3.2. Type-0 test, engine connected : Not applicable



Measured force applied to the controls

(km/h) (m/s2) (N) Unladen, dry brakes braking device applied

30% Vmax. 18 6.0 < 500

55% Vmax. (additional test) 33 5.9 < 500

80% Vmax. (max. 160 km/h) 48 5.9 < 500


Test Report No.: 84-2002/24-00793/14-00





3.3. Type-1 test, (fade test) : Not applicable

Distance between the initiation of two consecutive stops : 1000 m Number of braking : 10




(km/h) (m/s2) (N) Laden, dry brakes


Type 1 test, with engine connected / automatic transmission under normal driving condition : Not applicable




(km/h) (m/s2) (N) Laden, dry brakes

Reference test Combined service brake

54 5.9 387


3.4. Parking brake test (if applicable) : The parking brake devices of all tested versions are

capable of holding the laden vehicle stationary on an 18% up or down gradient.


Test Report No.: 84-2002/24-00793/14-00





Test minutes of coupling devices attachment Appendix 23

0. Test condition

0.1. Test date : May 7 to 14, 2014

0.2. Test site : Lu-Kang / Taiwan

1. Test facilities : The test equipment used was in compliance with the requirements of the directive.

2. Test vehicle(s)

2.1. Type : AX700-UL Variant : Not applicable Version : Not applicable

2.2. Identification number : RK3AX36204A000003

3. Test results : Passed

Unladen mass

348 kg Dynamic test force, F (F=±0.6D)

1.884 kN

Technically permissible maximum mass, T

542 kg Test frequency 4 Hz

Maximum towable mass, R

782 kg Test cycle 2,000,000

D value 3.14 kN

Results

No cracks, fractures or visible external damage

or any permanent distortion after test

S value 35 kg

Dynamic Test

Test angle -15° or +15° -20° or +20°


Issue date: July 16, 2014 Doc. No.: AX700-UL-2002/24-01 Extension Application

PAGE 1 / 20

2002/24/EC INFORMATION DOCUMENT

PART 1

A. INFORMATION RELATING JOINTLY TO MOPEDS, MOTOR CYCLES, MOTOR TRICYCLES AND QUADRICYCLES

0. General

0.1. Make : Access


Variant : N/A

Version : N/A

0.2.1. Commercial name : Access Motor, as option: SS250R, Hammel, Quadzilla, Bogart Patriot, Nexmotor, Tomahawk, Apollo, Spike, Speed, Maverick, TKM ,FOCUS, TENA, TRITON, MAX, APACHE, Burelli, Warrior, GOES

0.3. Means of type identification if stated on vehicle

: ???AX3???????????

0.3.1. Location of that means of identification : On the right side of frame body, see drawing no: 71000-A36-H00

0.4. Vehicle category : L7e

0.5. Name and address of manufacturer Address


0.5.1. Name(s) and address(s) of assembly plants : Access Motor Co., Ltd. No. 5, Chung-Hsin Rd., Chia-Tai Industrial Zone, Tai-Pao City, Chia-Yi Hsien 612, Taiwan

0.6. Name and address of manufacturer‘s authorized representative, if any

: N/A

0.7. Location and method of affixing statutory inscriptions to the chassis

: Riveted on the right side of frame body, see drawing no: 71000-A36-H00

0.7.1. The serial numbering of the type begins with No.

:

RK3AX36204A000001

0.8. Position and method of affixing the component type-approval mark for components and separate technical units

: Components approval marks are fixed by mold , engraving of sticker to the components.



PAGE 2 / 20

1. General arrangement of vehicles

1.1. Photos and/or drawings of a typical vehicle : See drawing no: 70000-A36-H00, 70000-A36-H21, 70000-A36-H30, 70000-A36-H41

1.2. Dimensional drawing of the complete vehicle

: See drawing no: 70000-A36-H00, 70000-A36-H21, 70000-A36-H30, 70000-A36-H41

1.2.1. Wheelbase : 1440± 10 mm

1.3. Number of axles and wheels : Two axles, two wheels on each axle

1.4. Position and arrangement of engine : Central and vertical

1.5. Number of seating positions : 1 or 2

1.6. Hand of drive – left or right : N/A

1.6.1. Vehicle is equipped to be driven in right-hand or left-hand rule of the road traffic

: Right -hand rule of the road traffic

2. Masses

2.0. Unladen mass : 348± 5 kg

2.1. Mass of vehicle in running order : 362± 5 kg

2.1.1. Distribution of that mass between the axles : Front- 199 kg, rear- 163 kg

2.2. Mass of vehicle in running order, together with rider

: 437± 5 kg

2.2.1. Distribution of that mass between the axles : Front- 228 kg, rear- 209 kg

2.3. Maximum technically permissible mass declared by the manufacturer

: 542± 5 kg

2.3.1. Division of that mass between the axles : Front- 249 kg, rear- 293 kg

2.3.2. Maximum technically permissible mass on each of the axles

: Front- 249 kg, rear- 293 kg

2.4. Maximum hill-starting ability at the maximum technically permissible mass declared by the manufacturer

: 10°

2.5. Maximum tow-able mass : 174 kg

2.6. Maximum mass of the combination : 716 kg

3. Engine

3.0. Manufacturer : Access Motor Co., Ltd.

3.1. Make : Access

3.1.1. Type : E20

3.1.2. Location of engine number : Right side of the crankcase

3.2. Spark- or compression-ignition engine

3.2.1. Specific characteristics of the engine

3.2.1.1. Operating cycle : Spark ignition, four stroke



PAGE 3 / 20

3.2.1.2. Number, arrangement and firing order of cylinders

: One, vertical

3.2.1.2.1. Bore : Ø102.0 mm

3.2.1.2.2. Stroke : 84.0 mm

3.2.1.3. Cylinder capacity : 686 cc

3.2.1.4. Compression ratio : 9.2± 0.1: 1

3.2.1.5. Drawings of cylinder head, piston(s), piston rings and cylinder(s)

: See drawing no: 12100-E20-H00, 12200-E20-H00, 13300-E20-000, 13310-E20-000~1, 13310-E20-000~2, 13310-E20-000~3

3.2.1.6. Idling speed min-1 :

Version AX700-U: 1600± 100 min-1

3.2.1.7. Maximum net power output : 10.80 kW at 4400 min-1

3.2.1.8. Net maximum torque : 40.60 Nm at 2000 min-1

3.2.2. Fuel : Diesel/ petrol/ mixture/ LPG/ other

3.2.3. Fuel tank

3.2.3.1. Maximum capacity : 21± 0.2 L

3.2.3.2. Drawing of tank with indication of materials used

: See drawing no: 12100-A27-H00

3.2.3.3. Diagram clearly indicating the position of the tank on the vehicle


3.2.3.4. Approval number of the fuel tank fitted : N/A

3.2.4. Fuel supply

3.2.4.1. Via carburetor(s) : Yes / no

3.2.4.1.1. Make(s) : N/A

3.2.4.1.2. Type(s) : N/A

3.2.4.1.3. Number fitted : N/A

3.2.4.1.4. Settings

3.2.4.1.4.1. Diffusers : N/A

3.2.4.1.4.2. Level in float chamber : N/A

3.2.4.1.4.3. Mass of float : N/A

3.2.4.1.4.4. Float needle : N/A

3.2.4.1.4.5. Fuel curve as a function of the air flow and settings required in order to maintain that curve

: N/A

3.2.4.1.5. Cold-starting system : N/A

3.2.4.1.5.1. Operating principle(s) : N/A

3.2.4.2. By fuel injection (solely in the case of compression ignition)

: Yes / no



PAGE 4 / 20

3.2.4.2.1. Description of system : N/A

3.2.4.2.2. Operating principle direct / indirect / turbulence chamber injection

: N/A

3.2.4.2.3. Injection pump N/A

3.2.4.2.3.1. Make(s) : N/A

3.2.4.2.3.2. Type(s) : N/A

3.2.4.2.3.3. Maximum fuel flow rate mm3 / per stroke or cycle at a pump rotational speed of min-1 or characteristic diagram

: N/A

3.2.4.2.3.4. Injection advance : N/A

3.2.4.2.3.5. Injection advance curve : N/A

3.2.4.2.3.6. Calibration procedure: test bench/engine : N/A

3.2.4.2.4. Regulator N/A

3.2.4.2.4.1. Type : N/A

3.2.4.2.4.2. Cut-off point : N/A

3.2.4.2.4.2.1. Cut-off point under load : N/A

3.2.4.2.4.2.2. Cut-off point under no load : N/A

3.2.4.2.4.3. Idling speed : N/A

3.2.4.2.5. Injection pipework N/A

3.2.4.2.5.1. Length : N/A

3.2.4.2.5.2. Internal diameter : N/A

3.2.4.2.6. Injector(s)

either

N/A

3.2.4.2.6.1. Make(s) : N/A

3.2.4.2.6.2. Type(s) : N/A

3.2.4.2.6.3. Opening pressure or characteristic diagram : N/A

3.2.4.2.7. Cold starting system Either

N/A

3.2.4.2.7.1. Make(s) : N/A

3.2.4.2.7.2. Type(s) : N/A

3.2.4.2.7.3. Description : N/A

3.2.4.2.8. Secondary starting device : N/A

3.2.4.2.8.1. Make(s) : N/A

3.2.4.2.8.2. Type(s) : N/A

3.2.4.2.8.3. Description of system : N/A

3.2.4.3. By fuel injection (solely in the case of spark-ignition)

: Yes / no



PAGE 5 / 20

3.2.4.3.1. Description of system : EFI (Electronic Fuel Injection system integrating with O2 sensor feedback)

3.2.4.3.2. Operating principle: injection into Induction manifold (single/ multiple point)/direct injection/ other(state which)

: Single point injection

3.2.4.3.2.1. Make(s) of the injection pump : BOSCH

3.2.4.3.2.2. Type(s) of the injection pump : marking: F01RB0M081

3.2.4.3.3. Injectors: opening pressure or characteristic diagram

: 300 kPa @ 12V

3.2.4.3.4. Injection advance : 0~360° CA

3.2.4.3.5. Cold-starting system Included in the EFI system

3.2.4.3.5.1. Operating principle(s) : A/F ratio controlled by the EFI system (dependent on the parameter of the water temp.)

3.2.4.3.5.2. Operating/setting limits : -20 °C~ 40 °C

3.2.4.4. Fuel pump : Yes / no

3.2.5. Electrical equipment

3.2.5.1. Nominal voltage : 12V, negative earth

3.2.5.2. Generator

3.2.5.2.1. Type : Shihlin

3.2.5.2.2. Nominal power : 280W

3.2.6. Ignition

3.2.6.1. Make (s) : BOSCH

3.2.6.2. Type(s) : 61115-A36-000

3.2.6.3. Operating principle : Electronic Control Unit

3.2.6.4. Ignition advance curve or operating set point

: See drawing no: 61115-A36-000

3.2.6.5. Static timing : 5° before TDC

3.2.6.6. Points gap : N/A

3.2.6.7. Dwell angle : N/A

3.2.6.8. Anti-radio interference system : Spark plug cap with resistor and resistor spark plug

3.2.6.8.1. Terminology and drawing of anti-radio interference equipment

: Spark plug: NGK R CR8E Ignition coil: see drawing no: 61110-A27-000, 61111-A27-000

3.2.6.8.2. Indication of the nominal DC resistance value and, in the case of resistive ignition lead, statement of nominal resistance per metre

: Plug cap: 10± 1.25 kΩ Spark plug: 5± 1 kΩ

3.2.7. Cooling system : Liquid / air



PAGE 6 / 20

3.2.7.1. Nominal setting for the engine-temperature control device

: Control valve opened when water is more than 75± 4°C

3.2.7.2. Liquid

3.2.7.2.1. Nature of liquid : Long life coolant additive: 50%, water: 50%

3.2.7.2.2. Circulating pump(s) : Yes / no

3.2.7.3. Air

3.2.7.3.1. Blower : Yes / no

3.2.8. Induction system

3.2.8.1. Supercharging : Yes / no

3.2.8.1.1. Make(s) : N/A

3.2.8.1.2. Type(s) : N/A

3.2.8.1.3. Description of system : N/A

3.2.8.2. Intercooler : With / without

3.2.8.3. Description and drawings of induction pipework and accessories (plenum chamber, heating device, additional air intakes, etc.)

: See drawing no: 16410-E20-000

3.2.8.3.1. Description of induction manifold : See drawing no: 16410-E20-000

3.2.8.3.2. Air filter, drawings : See drawing no: 17300-E20-H00, 17300-E20-000-1, 17300-E20-000-2

3.2.8.3.2.1. Make(s) : Cheng Tong

3.2.8.3.2.2. Type(s) : E20 (marking: 17300-E20-000-2)

3.2.8.3.3. Inlet silencer, drawings : See drawing no: 17320-E20-000

3.2.8.3.3.1 Make(s) : Cheng Tong

3.2.8.3.3.2 Type(s) : E20

3.2.9. Exhaust system

3.2.9.1. Drawing of complete exhaust system : See drawing no: 12160-A36-000_01, 12164-A27-H00

3.2.10. Minimum cross-section of the inlet and exhaust ports

: See drawing no: 12200-E20-H00

3.2.11. Induction system or equivalent data

3.2.11.1. Maximum, valve lift, opening and closing angles in relation to the dead centres, or data concerning the settings of other possible systems

: See drawing no: 25100-E20-H00

3.2.11.2. Reference and/or setting ranges : 0.06~0.1 mm

3.2.12. Measures taken against air pollution

3.2.12.1. Device for recycling crankcase gases, solely in the case of four-stroke engines

: See drawing no: 11350-E20-H00 (R-crankcase venthole system)



PAGE 7 / 20

3.2.12.2. Additional anti-pollution devices (if any, and if not covered by another heading)

: No

3.2.12.2.1. Catalytic converter : Yes / no

3.2.12.2.1.1. Number of catalytic converters and elements

: 1

3.2.12.2.1.2. Dimensions, shape and volume of the catalytic converter(s)


3.2.12.2.1.3. Type of catalytic action : 3 way catalytic converter

3.2.12.2.1.4. Total charge of precious metal : See drawing no: 12165-A27-H00

3.2.12.2.1.5. Relative concentration : See drawing no: 12165-A27-H00

3.2.12.2.1.6. Substrtae (structure and material) : See drawing no: 12165-A27-H00

3.2.12.2.1.7. Cell density : 100 cpsi

3.2.12.2.1.8. Type of casing for the catalytic converter(s) : See drawing no: 12165-A27-H00

3.2.12.2.1.9. Location of the catalytic converter(s) : See drawing no: 12160-A36-000_01

3.2.12.2.2. Oxygen sensor : Yes / no

3.2.12.2.2.1. Type : 0258006937 LSF4

3.2.12.2.2.2. Location : See drawing no. 12164-A27-H00

3.2.12.2.2.3. Control range : Rich>600mv, Lean<450mv

3.2.12.2.3. Air injection : Yes / no

3.2.12.2.3.1. Type : Pulse air

3.2.12.2.4. Exhaust gas recirculation : Yes / no

3.2.12.2.4.1. Characteristics : N/A

3.2.12.2.5.. Other systems : N/A

3.2.13. Location of the coefficient of absorption symbol

: N/A

3.3. Electric traction motor

3.3.1. Type : N/A

3.3.1.1. Maximum continuous rated power : N/A

3.3.1.2. Operating voltage : N/A

3.3.2. Battery

3.3.2.1. Number of cells : N/A

3.3.2.2. Mass : N/A

3.3.2.3. Capacity : N/A

3.3.2.4. Location : N/A

3.4. Other motors or combinations of motors : N/A

3.5. Cooling system temperatures permitted by the manufacturer



PAGE 8 / 20

3.5.1. Liquid cooling

3.5.1.1. Maximum temperature at outlet : 90°C

3.5.2. Air cooling : N/A

3.5.2.1. Reference point : N/A

3.5.2.2. Maximum temperature at reference point : N/A

3.6. Lubrication system

3.6.1. Description of system : Lubricant oil splashed to the cylinder camshaft by oil pump

3.6.1.1. Location of oil reservoir : Below the crankcase

3.6.1.2. Feed system : Oil pump

3.6.2. Lubricant mixed with the fuel

3.6.2.1. Percentage : N/A

3.6.3. Oil cooler : Yes / no

3.6.3.1. Drawing(s) : N/A

3.6.3.1.1. Make(s) : N/A

3.6.3.1.2. Type(s) : N/A

4. Transmission

4.1. Diagram of transmission system : See drawing no: 22100-E20-H00

4.2. Type : CVT

4.3. Clutch : Centrifugal

4.4. Gearbox

4.4.1. Type : Automatic / manual

4.4.2. Method of selection : By hand / foot



PAGE 9 / 20

4.5. Gear ratios

N R1 R2 R3 Rt

Minimum continuously variable transmission

1 2 …

Maximum continuously variable transmission

Reverse gear

1:1

1:1

1:1

H gear: 1:4.119 L gear: 1:6.951

H gear: 1:1.955 L gear: 1:3.299

1:7.174

1:3.667

1:3.667

1:3.667

H gear: 1:15.104 L gear: 1:25.489

H gear: 1:7.169 L gear: 1:12.097

1:26.307

N : gear ratio R1 : primary ratio (ratio of engine speed to rotational speed of primary gearbox shaft). R2 : secondary ratio (ratio of rotational speed of primary shaft to rotational speed of secondary shaft in gearbox). R3 : final drive ratio (ratio of rotational speed of gearbox output shaft to rotational speed of driven wheels). Rt : overall ratio

4.5.1. Brief description of the electrical and/or electronic components used in the transmission

: N/A

4.6. Maximum speed of vehicle and gear in which it is reached

:

60 km/h (@ H gear)

4.7. Speedometer

4.7.1. Make(s) : KOSO

4.7.2. Type(s) : A27 or A27-1

4.7.3. Photographs and/or drawings of the complete system

: See drawing no: 63300-A27-H01, 63300-A27-H11, 62120-A27-H00

4.7.4. speed range displayed : 63300-A27-H01: 0~ 150 km/h (0~ 93 mph) 63300-A27-H11: 0~ 199 km/h (0~ 124 mph)

4.7.5. Tolerance of the measuring mechanism of the speedometer

:

km/h 37

Tolerance 0~ +8.1 %

Tolerance Range

0~ 3.0 km/h

4.7.6. Technical constant of the speedometer : Setting parameter: 450 (60 km/h @ 1500 rpm)

4.7.7. Method of operation and description of the drive mechanism

: Magnetic detect, digital display with blue back-lighting



PAGE 10 / 20

4.7.8. Overall transmission ratio of the drive mechanism

: N/A

5. Suspension

5.1. Drawing of suspension arrangement : See drawing no: 70000-A36-H00, 70000-A36-H21, 70000-A36-H30, 70000-A36-H41

5.1.1. Brief description of the electrical and/or electronic components used in the suspension

: N/A

5.2. Tyres (category, dimensions and maximum loading) and rims (standard type)

: Front Category Normal Size AT25×8-12 Max load 155 kg Rim 6×12

Rear Category Normal Size AT25×10-12 Max load 190 kg Rim 7.0×12

5.2.1. Nominal rolling circumference : Front & rear- 1995 mm

5.2.2. Tire pressures recommended by the manufacturer

: 35 kPa

5.2.3. Tyre/ wheel combinations : Front- 25×8-12/ 6×12 Rear- 25×10-12/ 7.0×12

5.2.4. Minimum-speed category symbol compatible with the theoretical maximum design speed of the vehicle

: F

5.2.5. Minimum load-capacity index with the maximum load on each tyre

: Front- 36, rear- 42

5.2.6. Categories of use compatible for the vehicle : Front and rear- normal

6. Steering

6.1. steering gear and control

6.1.1. Type of gear : N/A (handle bar on the front shaft steering)

6.1.2. Brief description of the electrical and/or electronic components used in the steering system

: N/A

7. Braking

7.1. Diagram of braking devices : See drawing no: 31115-A27-H00

7.2. Front and rear brakes, disc and/or drum : Front and rear- disc

7.2.1. Make(s) : Yun Chen, as option: Horng Fuu



PAGE 11 / 20

7.2.2. Type(s) : Yun Chen: Front- 31335-A13-000 (RH), 31336-A13-000(LH) Rear- 31345-A27-000 (RH), 31346-A27-000 (LH)

Horng Fuu: Front- 31335-A13-010 (RH), 31336-A13-010(LH) Rear- 31345-A27-020 (RH), 31346-A27-020 (LH)

7.3. Drawing of parts of the brake system

7.3.1. Shoes and/or pads : N/A

7.3.2. Linings and/or pads : See drawing no: Front- 31337-A13-000~1 Rear- 31337-A03-001~1, 31337-A03-001~2,

7.3.3. Brake levers and/or pedals : Brake levers: see drawing no: 31405-A03-001, 31460-A03-000 Brake pedal: see drawing no: 31408-A27-000

7.3.4. Hydraulic reservoirs : See drawing no: 31405-A03-001, 31460-A03-000, 31406-A27-000 (Yun Chen), 31406-A32-010 (Horng Fuu)

7.4. Other devices: drawing and description : Mechanical parking brake device acting on the rear axle, see drawing no: 31115-A27-H00, 31470-A27-000, 31340-A13-000

7.5. Brief description of the electrical and/or electronic components used in the braking system

: N/A

8. Lighting and light-signaling devices

Trade Mark Type Quantity/

Color Tell Tale Approval No. Remark

Driving lamp JUTE JUTE PJ-H 2 / White

E9-001066 Max 53.4

lux

Passing lamp JUTE JUTE PJ-L 2 / White N.A. E9-001067 --

Front position lamp

JUTE JUTE PJ-H 2 / White Illumination

of speedometer

E9-50R-001066 --

Front direction indicator

WAMA ou SB 82-A003R/L 2 / Amber

E6-50R-000053 --

Front direction indicator (optional)

JUTE JUTE W013 2 / Amber

E4-6R-016962 Version B

Rear direction Indicator

WAMA ou SB 82-A003R/L 2 / Amber

E6-50R-000053 --



PAGE 12 / 20

Rear direction Indicator (optional)

JUTE JUTE TL006 2 / Amber

E9-016395 --

Rear position Lamp

SB SB14-001 1 / Red Illumination

of speedometer

E4-50R-0013256 --

Rear position Lamp (optional)

JUTE JUTE TL006 2 / Red Illumination

of speedometer

E9-026395

Stop lamp SB SB14-001 1 / Red N.A. E4-50R-0013256 --

Stop lamp (optional)

JUTE JUTE TL006 2 / Red N.A. E9-026395

License Plate illuminator

JUTE PL004 1 / White N.A. E4-50R-001780 --

Rear retro reflector

JUTE 9605 JUTE 9605 2 / Red N.A. E13*03R00*03R02*0279*01

--

Rear retro reflector (optional)

JUTE 9823 2 / Red N.A. E11-023578 --

Rear retro reflector

DBM or K-LITE KM-202 2 / Red N.A. E9-021269 --

Rear fog lamp (optional)

FUAN or FOT FUAN 0089 1 / Red

E9-001240 --

8.2. Diagram showing the location of the lighting and light-signalling devices


8.3. Hazard warning lamps : Yes

8.4. Additional requirements relating to special vehicles

: N/A

8.5. Brief description of the electrical and/or electronic components used in the lighting system and in the light-signalling system

: N/A

9. Equipment

9.1. Coupling devices

9.1.1. Type: : Hook/ ring/ other

9.1.2. Photographs and/ or drawing showing the position and the construction of the coupling devices

: See drawing no: 70000-A27-H10-2, 71403-A27-H10, 71402-A20-H01

9.2. Arrangement and identification of controls, tell-tales and indicators



PAGE 13 / 20

9.2.1. Photographs and/or drawings of the arrangement of the symbols, controls, tell-tales and indicators

: See drawing no: 61101-A27-000, 63300-A27-H01

9.3. Statutory inscriptions

9.3.1. Photographs and/or drawings showing the location of the statutory inscriptions and the chassis number


9.3.2. Photographs and/or drawings showing the official part of the inscriptions


9.3.3. Photographs and/or drawings of the chassis number


9.4. Device(s) to protect against unauthorized use

9.4.1. Type of device(s) : Type 1

9.4.2. Summary description of device(s)used : Steering shaft is locked to the frame body by a lock pin, see drawing no: 70000-A36-H00, 70000-A36-H21, 70000-A36-H30, 70000-A36-H41

9.5. Audible warning device(s)

9.5.1 Summary description of device(s) used and : One electromagnetic DC horn

9.5.2. Make(s) : CHEN LEN

9.5.3. Type(s) : CL-2

9.5.4. Type-approval mark : II-E4-000014

9.5.5. Drawing(s) showing the location of the audible warning device(s) in relation to the structure of the vehicle


9.5.6. Details of the method of attachment, including the part of the vehicle structure to which the audible warning device(s) is (are) attached


9.6. Location of rear registration plate : See drawing no: 70000-A36-H00, 70000-A36-H21, 70000-A36-H30, 70000-A36-H41

9.6.1. Inclination of plane in relation to the vertical

: 28°

B. INFORMATION RELATING SOLELY TO TWO-WHEEL MOPEDS AND MOTORCYCLES

Not applicable

C. INFORMATION RELATING SOLELY TO THREE-WHEEL MOPEDS, MOTOR TRICYCLES AND QUADRICYCLES

1. Dimensions and masses



PAGE 14 / 20

1.1. Dimensions to be complied with when building unbodied chassis

1.1.1 Length : 2250± 10 mm

1.1.2. Width : 1200± 10 mm

1.1.3. Unladen height : 1495± 10 mm

1.1.4. Front overhang : 420± 10 mm

1.1.5. Rear overhang : 390± 10 mm

1.1.6. Limit position for centre of gravity of bodied vehicle

: N/A

1.2. Masses

1.2.1. Maximum payload declared by manufacturer

: 105 kg

2. Equipment

2.1. Bodywork

2.1.1. Nature of bodywork : N/A

2.1.2. General dimensional arrangement drawing of inside

: N/A

2.1.3. General dimensional arrangement drawing of outside

: N/A

2.1.4. Materials and methods of manufacture : N/A

2.1.5. Passenger doors, locks and hinges : N/A

2.1.6. Configuration, dimensions, direction and maximum opening angle of doors

: N/A

2.1.7. Drawing of locks and hinges and their location in the doors

: N/A

2.1.8. Technical description of locks and hinges : N/A

2.2. Windscreen and other glazing

2.2.1. Windscreen

2.2.1.1. Materials used : N/A

2.2.2. Other glazing

2.2.2.1. Materials used : N/A

2.3. Windscreen wiper(s) : N/A

2.3.1. Detailed technical description : N/A

2.4. windscreen washer(s) : N/A

2.4.1. Detailed technical description

: N/A

2.5. Defrosting and demisting : N/A

2.5.1. Detailed technical description : N/A

2.6. Rear-view mirror(s)



PAGE 15 / 20

2.6.1. Make : FU

2.6.2. Type-approval mark : L-E11-001087

2.6.3. Variant : N/A

2.6.4. Drawing(s) showing the location of the rear-view mirror(s) in relation to the structure of the vehicle


2.6.5. Detailed information on the method of attachment, including that part of the structure of the vehicle to which the rear-view mirror is attached

: Mirrors are mounted on the handle bar by using screws

2.7. Seats

2.7.1. Number : 1 or 2

2.7.2. Location : Center of vehicle

2.7.3. Coordinates or drawing of the R point

2.7.3.1. Driving seat : N/A

2.7.3.2. Other seats : N/A

2.7.4. Intended seat-back inclination : N/A



2.7.5. Seat adjustment range, where appropriate



2.8. Passenger-compartment heating system

2.8.1. Summary description of type of vehicle in respect of the heating system if this uses heat from the liquid engine coolant

: N/A

2.8.2. Detailed description of the type of the vehicle in respect of the heating system if this uses the cooling air or exhaust gases as a heat source, including

: N/A

2.8.2.1. An overall drawing of the heating system giving its location on the vehicle

: N/A

2.8.2.2. An overall drawing of the heat exchanger used in systems utilizing the heat from the exhaust gases, or of the parts where that exchange takes place

: N/A

2.8.2.3. A sectional drawing of the heat exchanger or parts where heat exchange takes place, together with a statement of the wall thickness, of the materials used and the characteristics of their surface

: N/A



PAGE 16 / 20

2.8.2.4. Specifications regarding the method of manufacture and technical data relating to other major components of the heating system, such as the fan

: N/A

2.9. Safety belts

2.9.1. Number and location of safety belts, together with a reference to the seats where that type of equipment may be installed

: N/A

2.10. Anchorages

2.10.1. Number and location of the anchorages : N/A

2.10.2. Photographs and/or drawings of the bodywork showing the true, effective location and dimensions of the anchorages, together with an indication of the R-point position

: N/A

2.10.3. Drawings of the anchorages and the parts of the structure of the vehicle to which they are attached

: N/A

2.10.4. Designation of the types of belts(*) authorized for attachment to the anchorages on the vehicle

: N/A

2.10.5. Description of a specific type of belt, one anchorage of which is attached to the seat back-rest or incorporates an energy-dissipation device

: N/A



PAGE 17 / 20

PART 2 SEPARATE DIRECTIVE APPROVAL NUMBERS

The following information shall be supplied on the vehicle to be type approved with regard to existing system,

separate technical unit or component approvals(*):

Heading No

Separate Directive No

Subject Approval No (1) Extension date

Variants and

versions covered

18 95/1/EC Maximum torque and maximum net power of engine

-- -- --

19

97/24/EC (C7) Anti-tampering measures for mopeds and motorcycles

-- -- --

20 97/24/EC (C6) Fuel tank -- -- --

25 95/1/EC Maximum design speed of vehicle

-- -- --

26 93/93/EEC Masses and dimensions -- -- --

27 97/24/EC (C10) Trailer coupling devices

-- -- --

28 97/24/EC (C5) Anti-air pollution measures

-- -- --

29 97/24/EC (C1) Tyres -- -- --

31 93/14/EEC Braking system -- -- --

32 2009/67/EC Installation of lighting and light-signalling devices on the vehicle

-- -- --

33 97/24/EC (C2) Lighting and light-signalling devices

-- -- --

34 93/30/EEC Audible warning device

-- -- --

35 2009/62/EC Position for the mounting of rear registration plate

-- -- --



PAGE 18 / 20

Heading No

Separate Directive No

Subject Approval No(1) Extension date

Variants and

versions covered

36 97/24/EC (C8) Electromagnetic compatibility

-- -- --

37 97/24/EC (C9) Sound level and exhaust system

-- -- --

38 97/24/EC (C4) Rear-view mirror(s) -- -- --

39 97/24/EC (C3) External projections -- -- --

40 2009/78/EC Stand (except in the case of vehicles having three or more wheels)

-- -- --

41 93/33/EEC Devices to prevent unauthorized use of the vehicle

-- -- --

42 97/24/EC (C12) Windows; windscreen wipers; windscreen washers; and so on

-- -- --

43 2009/79/EC Passenger hand-hold for two-wheel vehicles

-- -- --

44 97/24/EC (C11) Anchorage points for safety belts and safety belts

-- -- --

45 2000/7/EC Speedometer -- -- --

46 2009/80/EC Identification of controls, tell-tales and indicators

-- -- --

47 2009/139/EC Statutory inscriptions -- -- --

(1) Examples are given in Annex V. (*) Information is not required in respect of systems, separate technical units or components which are to be included in the examination or testing for the granting of whole vehicle type approval. Note: The heading numbers are aligned with Annex I (list of requirements).



PAGE 19 / 20

LIST OF CONTENTS Item Title Drawing No. Notes

1. Frame 71000-A36-H00 2. Vehicle over view 70000-A36-H00 3. Vehicle over view 70000-A36-H21 4. Vehicle over view 70000-A36-H30 5. Vehicle over view 70000-A36-H41 6. Cylinder 12100-E20-H00 7. Cylinder head 12200-E20-H00 8. Piston 13330-E20-000 9. Piston ring (1st) 13310-E20-000~1 10. Piston ring (2nd) 13310-E20-000~2 11. Piston ring (oil) 13310-E20-000~3 12. Fuel cup comp 12100-A27-H00 13. ECU 61115-A36-000 14. Ignition coil 61110-A27-000 15. Plug cap 61111-A27-000 16. Intake pipe 16410-E20-000 17. Air filter Assy 17300-E20-H00 18. Case, AIR/C 17300-E20-000-1 19. Cover, AIR/C 17300-E20-000-2 20. Inlet silencer 17320-E20-000 21. Exhaust muffler comp 12160-A36-000_01 22. Front Exhaust Pipe 12164-A27-H00 23. Valve angle 25100-E20-H00 24. R-crankcase venthole system 11350-E20-H00 25. Catalyst 12165-A27-H00 26. Transmission system 22100-E20-H00 27. Speedometer 63300-A27-H01 28. Speedometer 63300-A27-H11 29. Speedometer system 62120-A27-H00 30. Diagram of braking system 31115-A27-H00 31. Pad (Front) 31337-A13-000~1 32. Inner pad (rear) / Outer pad (rear) 31337-A03-001~1 & ~2 33. Brake lever Ass’y (LH) 31405-A03-001 34. Brake lever Assy (RH) 31460-A03-000 35. Brake pedal 31408-A27-000 36. Master cylinder 31406-A27-000 37. Master cylinder 31406-A32-010 # 38. Mechanical parking brake lever 31470-A27-000 39. Caliper-parking 31340-A13-000 40. Front brake caliper (RH) 31335-A13-000 41. Front brake caliper (LH) 31336-A13-000 42. Rear brake caliper (RH) 31345-A27-000 43. Rear brake caliper (LH) 31346-A27-000 44. Front brake caliper (RH) 31335-A13-010 #



PAGE 20 / 20

45. Front brake caliper (LH) 31336-A13-010 # 46. Rear brake caliper (RH) 31345-A27-020 # 47. Rear brake caliper (LH) 31346-A27-020 # 48. Front and Rear disc 31305-A13-000 49. Telltales, controls and indicators 61101-A27-000 50. Manufacturer’s data plate 71237-A36-H00 51. VIN code 71236-A36-H00 52. Radiator Assembly 15230-A27-000 53. O2 sensor 63215-A27-H00 54. Electrical circuit diagram A27 (AX700) 55. Injector 16250-E20-000 56. Throttle Body 16100-E20-000 57. Overall view 70000-A27-H10-2 # 58. Bracket Assy 71403-A27-H10 # 59. Coupling Ball 71402-A20-H01 #

1

ABD CE

BD CE

23

45

67

887

65

43

R-7301-02-4

A

REV.

修正紀錄 Revision record

0修訂處

核准

日期

修訂者

雍御企業股份有

限公

司A

ccess M

oto

r C

o.,L

td.

製圖 DRAWN

日期 DATE

材質及規格 MATERIAL&SIZE

表面處理 SURFACE FINISH

熱處理 HEAT TREAT

審圖 CHECKED

核准 APPROVED

日期 DATE

圖紙 PAPER

數量 QTY

比例 SCALE

單位 UNIT

圖號 DWG NO.

圖名 DWG NAME

A3

台

mm

Redactor

Approved

Date

Loc

atio

n

21

量產圖發行

蔡濠璘

2014/06/18

腳煞車總泵

31406-A32-010

1

如表

如表

蔡濠璘

2014/06/18

雍御

企業股份有限

公司

圖面

發行管

制章

2014.6.18

雍御

企業股份有限

公司

圖面

量產

圖

2014.6.18

1

ABD CE

BD CE

23

45

67

887

65

43

R-7301-02-4

A

REV.


0修訂處

核准

日期

修訂者


限公

司A

ccess M

oto

r C

o.,L

td.

製圖 DRAWN

日期 DATE




審圖 CHECKED

核准 APPROVED

日期 DATE

圖紙 PAPER

數量 QTY

比例 SCALE

單位 UNIT

圖號 DWG NO.

圖名 DWG NAME

A3

台

mm

Redactor

Approved

Date

Loc

atio

n

21

量產圖發行

蔡濠璘

2014/06/18

前剎車卡鉗總成

-A13-010

1

如表

如表

31335

31336

右左蔡濠璘

2014/06/18

雍御

企業股份有限

公司

圖面

發行

管制

章

2014.6.18

雍御

企業股份有限

公司

圖面

量產

圖

2014.6.18

1

ABD CE

BD CE

23

45

67

887

65

43

R-7301-02-4

A

REV.


0修訂處

核准

日期

修訂者


限公

司A

ccess M

oto

r C

o.,L

td.

製圖 DRAWN

日期 DATE




審圖 CHECKED

核准 APPROVED

日期 DATE

圖紙 PAPER

數量 QTY

比例 SCALE

單位 UNIT

圖號 DWG NO.

圖名 DWG NAME

A3

台

mm

Redactor

Approved

Date

Loc

atio

n

21

量產圖發行

蔡濠璘

2014/06/20

後剎車卡鉗總成

-A27-020

1

如表

如表

31345

31346

右左

雍御

企業股份有限

公司

圖面

發行管

制章

2014.6.26

雍御

企業股份有限

公司

圖面

量產

圖

2014.6.26

蔡濠璘

2014/06/26

1

AG

23

45

610

98

7

34

56

109

87

F E D C B

AG F E D C B

R-7301-02-4

2014

/05

/17

蔡濠璘黑色

ED

N/A

11RE

V.修正

紀錄 Revision record

1修

訂處

核准

日期

修訂

者

雍御

企業

股份

有限

公司

Access M

oto

r C

o.,L

td.

製圖

DRAW

N日

期 D

ATE

材質及

規格

MATERIA

L&S

IZE

表面

處理

SURFACE

FI

NIS

H

熱處理

HEAT TR

EAT

審圖

CHEC

KED

核准

APPR

OVED

日期

DATE

圖紙

PAPE

R

數量

QTY

比例

SCAL

E

單位

UNIT

圖號

DWG

NO.

圖名

DWG

NAM

E

A2

台

mm

Red

actor

App

rove

dDat

eLocation

2

21

蔡濠璘

2014/05/19

Brac

ket

Assy

71403-A

27-

H10

1:2

AA

剖面

A-A

1

3

項次

零件

號

碼

零件

名

稱

材質

數量

17140

3-A

27-

A10

_1

主體

SPHC t=

10.

01

27140

3-A

27-

A10

_2

補強

座SPHC-P

t=3

.0

1

37140

3-A

27-

A10

_3

下補

強板

SPHC-P

t=5

.0

1

註：1.不

得有害之

焊渣及假焊現象。

2.E.D

電著膜厚為

0.015~0.02

5mm，

光澤度

25GU

以上。

3

.焊渣於每

1

²內，不得超過兩

粒以上。

4.品

質如有爭議

以限度樣品為依據。

5.津

銀素材料

號:71403

-A27-A10-A。

2

25 2x

55

8x

45.00A

d3

A

33.00

314.7

10°

152.5

28.0

未標

註之

公差

表

DE

C.

X.

=

± 2

.0

X

.X =

± 1

.0

X

.XX

= ±

0.5

AN

GL

E =

± 2

°

如表列

25

37.6

8

3.5

字深約0.3~0.5mm

O20.00

25

25

x2

x10

25

40

x2

10

局部

詳圖

B

1:1

B

1

D3.68->D3.14; 版0->版1

B5; G3

2014/05

/30

蔡濠璘

1

13.0

3.0

access motor co., ltd.ax700-ul%e7%b3… · 1. trade name or mark of the device : access 2....

Documents