abu dhabi specification ةينفلا يبظوبأ ريياعم...the abu dhabi quality and...
TRANSCRIPT
Abu Dhabi Specification معايير أبوظبي الفنية
التفتيش على معدات الرفع وملحقاتها
Inspection of Lifting
Equipment and Lifting
Equipment Accessories
ADS 22/2018 22/2018 م أ ف
2
Table of Contents
Sr. Content Page
1 Forward 4
2 Purpose 4
3 Scope 5
4 Definitions 5
5 Requirements 7
6 References 9
7 Appendices 10
Appendix A -
Lists of lifting Equipment’s and Lifting Accessories 11
Appendix B –
LEEA-060 Pictorial Guide to Standards Version 2 October 2017 20
Appendix C –
QCC LE01 Certificate of Thorough Examination -Lifting Gears Safe ,
QCC LE02 Certificate of Thorough Examination -Lifting Gears Unsafe &
QCC LE03 Certificate of Through Examination-Defect Report List V2
20-04-2016
81
3
Amendment Page
To ensure that each copy of this ADS contains a complete record of amendments, the Amendment
Page is updated and issued with each set of revised/new pages of the document. This ADS is a
live document which can be amended when necessary. QCC operates Lifting Equipment and
Accessories Working Group which prepared this document and can review stakeholder
comments in order to review and amend this document, issuing an updated version when
necessary.
Amendment Discard Insert
No
Date
*Sections Changed
Page(s)
Issue no
Page(s)
Issue no
1 Dec/2017 Document launched 7
2 Aug/2018 Appendices 28
4
About the Abu Dhabi Quality & Conformity Council
The Abu Dhabi Quality and Conformity Council (QCC) was established by law No. 3 of 2009,
issued by His Highness Sheikh Khalifa Bin Zayed Al Nahyan, President of the UAE.
QCC is responsible for the development of Abu Dhabi Emirate’s Quality Infrastructure, which
enables industry and regulators to ensure that products, systems, and personnel can be tested and
certified to UAE and International Standards.
Products, Services, and Systems certified by the QCC may receive the Abu Dhabi Trustmark.
The Trustmark is designed to communicate that a product, service, or system conforms to
various safety and performance standards that are set by Abu Dhabi regulators.
1. Foreword
The Lifting Equipment and Accessories Working Group was established in October 2015 to
identify and consolidate all Emirate’s lifting equipment and accessories inspector’s requirements
to perform a lifting equipment and accessories inspection. In order to do so, the working group
examined various existing standards and technical regulations related to the subject. It is
intended also to prioritize the lifting equipment and accessories inspection operational and
planning standards topics to be studied and reviewed at the level of Abu Dhabi Emirate. Abu
Dhabi Specifications (ADS) is developed on subjects that have no clear specifications or local
legislation.
2. Purpose
The ADS for Lifting Equipment and Accessories Inspection is intended to achieve the following:
2.1 Contribution to the achievement of Abu Dhabi Vision.
2.2 Support the expansion of the industry to meet the emerging needs and requirements while
maintaining the best standards.
2.3 Facilitation and enhancement of audit/inspection standard.
5
Acknowledgments
The QCC would like to thank the members of the working group listed below:
# Name Entity
1 Abdelhameed Salah ESMA
2 Ibrahim Khaled Ahmed DMAT
3 Belal Ktaish TÜV SUD MIDDLE EAST
4 John Ewing OSHAD
5 Omar Al Ashram OSHAD
6 Venkatesan C. V TÜV NORD MIDDLE EAST
7 Michael Chatfield TÜV NORD MIDDLE EAST
8 Abdelbaset Shokr Royal
9 Jagadeesan Elumalai BUREAU VERITAS
10 Kevin Crilly LEEA
11 Osama A. Melhem QCC
3. Scope
3.1 This regulation lays down standards for examination/inspection of lifting equipment and
associated accessories within Abu Dhabi. These are primarily addressed to all competent
local authorities, owners of lifting equipment, employers that use lifting equipment whether
hired or owned. This regulation does not cover passenger lifts, elevators or escalators used
in buildings. All concerned shall ensure compliance to the requirements of these standards.
3.2 These specifications are not substitutes for any other legislation issued in the UAE, and
the Inspection Bodies shall comply with the relevant UAE Federal and Abu Dhabi
legislations.
4. Definitions
Approval Body
Abu Dhabi Quality & Conformity Council.
Accredited Body
A body that issues credentials or certifies third parties against official standards and are
themselves formally accredited by accreditation bodies (such as UKAS); hence they are
sometimes known as "accredited certification bodies". The accreditation process ensures that
their certification practices are acceptable, typically meaning that they are competent to test and
certify third parties, behave ethically, and employ suitable quality assurance i.e. LEEA or
equivalent.
Inspection Body
An organization with sufficient competency to enable them to carry inspection and testing of
lifting equipment.
6
Lifting Equipment
Lifting equipment is a generic term used throughout this code to indicate loosely all lifting
accessories, lifting gear and appliances.
Lifting Appliance
A lifting appliance is any machine which is able to raise, lower or suspend a load but excluding
machines incorporating a guided load (i.e. lifts & elevators) and continuous mechanical handling
devices (i.e. conveyors).
Lifting Accessory
The term lifting accessory, or accessory for lifting, is used in current legislation to mean an item
of equipment used to attach the load to the lifting appliance and generally covers equipment
previously referred to as lifting gear or lifting tackle.
Lifting Gear
Lifting gear is any item used to connect a load to a lifting machine or appliance, but which is not
in itself capable of providing any movement to lift or lower the load.
Lifting gear is in some circumstances known as lifting tackle and generally falls within the
definition of lifting accessories referred to in current legislation
Competent Person
For the purpose of thoroughly examining lifting equipment, the definition of a Competent Person
is a person having such practical and theoretical knowledge and experience of the equipment
which is to be thoroughly examined that will enable him/her to detect defects or weaknesses
which is the purpose of the examination to discover and assess their importance to the safety of
the equipment.
The Competent Person should have the maturity to seek such specialist advice and assistance as
may be required to enable him/her to make necessary judgements and be a sound judge of the
extent to which he/she can accept the supporting opinions of other specialists. He/she must be
able to certify with confidence whether it is free from patent defect and suitable in every way for
the duty for which the equipment is required. It is the view of the LEEA that competency can be
a corporate responsibility.
Thorough Examination
A thorough examination is a visual examination carried out by a Competent Person carefully and
critically and, where appropriate, supplemented by other means such as measurement and testing
to check whether the equipment is safe to use.
Notes:
(1) The meaning of this term has become broader because of LOLER and now encompasses any
testing appropriate for the purpose of the thorough examination. The term ‘testing’ includes,
for example, proof load testing, operational testing at lower loads and non-destructive testing.
(2) The period between thorough examinations must be established by management based on
statutory requirements for the equipment, severity of service conditions, nature of the lifts,
prior experience and the recommendation of the Competent Person. In no case must the
period between thorough examinations exceed the statutory requirements given in this
specification.
7
Responsible Person
The term Responsible Person is used to describe a person who has sufficient knowledge and
training to enable him/her to recognize obvious defects and is responsible to his/her employer for
the ‘in-service’ inspection of equipment.
In-Service Inspection
In-service inspection is a visual inspection carried out by the Responsible Person
(owner/user/operator) to check for obvious signs of damage or wear which might affect the
equipment’s fitness for use.
Report of Thorough Examination
A report of a thorough examination is a report issued by the Competent Person giving the results
of the thorough examination, which will detail the defects found or include a statement that the
item is fit for continued safe use. Where the Competent Person has carried out a test as part of
the examination, the report will also contain details of the test.
5. Requirements
Requirements for Lifting Equipment Inspection Bodies
1. Only Inspection Bodies (IB) registered by Abu Dhabi Quality & Conformity Council
(ADQCC) shall be authorized to undertake examinations of lifting equipment and lifting
accessories;
2. To register as an Inspection Body, entities should be able to demonstrate that their facilities,
equipment, inspector qualifications, and inspection activities etc are subject to independent
assessment and ongoing audit by a recognised lead industry body, such as the Lifting
Equipment Engineers Association (LEEA) or equivalent
3. Lifting Equipment Inspection Bodies shall be sufficiently independent and impartial to
allow objective decisions to be made.
4. Lifting Equipment Inspection Bodies shall thoroughly examine the equipment; this
examination should include but not be limited to the parts that are subject to wear and tear,
and deterioration and which could lead to dangerous situations.
5. Thorough examination is needed at several points during the life of lifting equipment:
(a) on initial use or following installation;
(b) periodically during its life to ensure it remains fit for use, i.e. statutory periods
(c) following certain exceptional circumstances, e.g. if it is damaged
6. Every employer shall ensure that lifting equipment is –
(a) thoroughly examined
8
(i) in the case of lifting equipment for lifting persons or an accessory for lifting, at least
every 6 months;
(ii) in the case of other lifting equipment, at least every 12 months; or
(iii) in either case, in accordance with an examination scheme; and
(iv) each time that exceptional circumstances which are liable to jeopardise the safety of
the lifting equipment have occurred; and,
(b) if appropriate for the purpose, is inspected by a competent person at suitable intervals
between thorough examinations,
7. Any examination scheme for lifting machines and accessories should take account of:
a. Their age and condition;
b. The environment in which they are to be used
c. The number of lifting operations and loads lifted.
For guidance refer to LEEA 032 Guidance to written schemes of examination 1st July 2000
8. Employers shall ensure that in the case of cranes with a variable radius a maximum SWL
test is carried out at least once every 4 years in line with the manufacturer’s instructions.
9. The examination scheme shall be preserved in the form of a document, which may be in
electronic format and should be secure from loss or unauthorized modification and it should
be authenticated by the competent person preparing the scheme.
10. The Inspection Body shall ensure that the competent personnel carrying out a thorough
examination have the relevant lifting equipment inspector accreditation from a competent
authority i.e. LEEA or equivalent and have such appropriate practical and theoretical
knowledge and experience of the lifting machines and accessories to enable them to
thoroughly examine, to detect defects or weaknesses and to assess their importance in
relation to the safety and continued use of the lifting equipment.
11. The Inspection Body shall ensure that all equipment used for inspection, measuring and
testing are calibrated in accordance with BS EN ISO 7500-1:2015 by approved calibration
bodies such as Emirates Authority for Standardization & Metrology (ESMA), Abu Dhabi
Quality and Conformity Council, Dubai Municipality and the records of such calibration
are maintained.
12. The Inspection Body shall not certify any lifting machines or lifting accessories without
proper thorough physical examination of the same.
13. The Inspection Body upon carrying out a thorough examination of lifting machines and
accessories shall notify the owner and user of any defect in the lifting equipment which in
their opinion is or could become a danger to persons and the lifting equipment shall be
quarantined or removed from use until the defects have been rectified and the lifting
equipment re-inspected and certified as safe for use.
14. The Inspection Body after undertaking a thorough examination of lifting machines and
accessories shall as soon as is practicable make a report of the thorough examination in
writing authenticated by them to the owner and user of the lifting equipment.
9
6. References
UAE Ministerial Order No 32 1982 Article 20
OSHAD-SF – Code of Practice 34.0 – Safe Use of Lifting Equipment and Lifting
Accessories.
Lifting Operations & Lifting Equipment Regulations 1998 UK Statutory Instrument S.I.
2307
Provision & Use of Work Equipment 1998 Statutory Instrument S.I. 2307
Document reference QCC LE 01 Certificate of Thorough Examination (Lifting
Equipment) – Safe
Document reference QCC LE 02 Certificate of Thorough Examination (Lifting
Equipment) – Unsafe
Document reference QCC LE 03 Defect Report (Lifting Equipment)
LEEA Lifting Equipment Examiners Handbook First Edition 2017
LEEA Lifting Equipment Examiners Quick Reference Guide First Edition 2017
LEEA 032 Written Schemes of Examination
LEEA 017 Process Control Procedures
LEEA 042 Technical Audit Requirements & Guidance
10
7. Appendices
1. Appendix A - Lists of lifting Equipment’s and Lifting Accessories
A-1 Lists of lifting Equipment’s
A-2 Lists of Lifting Accessories
2. Appendix B - Lifting Examiners Guide Document reference: 066
3.
Appendix C - QCC LE01 Certificate of Thorough Examination -Lifting
Gears Safe , QCC LE02 Certificate of Thorough Examination -Lifting
Gears Unsafe & QCC LE03 Certificate of Through Examination-Defect
Report List
C-1 QCC LE01 Certificate of Thorough Examination -Lifting Gears Safe
C-2 QCC LE02 Certificate of Thorough Examination -Lifting Gears Unsafe
C-3 QCC LE03 Certificate of Through Examination-Defect Report List
11
Appendix A – Lists of lifting Equipment’s and Lifting
Accessories
A-1 Lists of lifting Equipment’s
S.NO. Field of Inspection Type and Range of
Inspection Standard
1 Mobile Crane/Crawler crane Test and Thorough
Examination
BS 7121- 1:2016,
BS 7121-2-3:2012
BS 7121-3-2017
2 Overhead Crane/ Gantry
crane
Test and Thorough
Examination BS 7121- 2- 7:2012+A1:2015
3 Tower Crane Test and Thorough
Examination BS 7121- 2- 5:2012
4 Construction Hoist Test and Thorough
Examination BS 7212:2016
5 Window/Painter's Cradle Test and Thorough
Examination BS EN 1808:2015
6 Escalators and passenger
conveyors
Test and Thorough
Examination BS EN 115-1:2017
7 Elevators/Lifts Test and Thorough
Examination
ASME A 17.1:2016
BS EN 81- 50:2014
BS EN 81- 20:2014
BS EN 81- 2 + A3
BS EN 81- 3 + A1
BS EN 81- 70
8 Fork lift Test and Thorough
Examination
BS EN ISO 3691-1:2012
BS EN ISO 3691-6:2015
BS EN ISO 3691-3:2016
BS EN 1459-1:2017
BS EN ISO 3691-2:2016
BS ISO 22915-5:2014
BS ISO 22915-1
12
S.NO. Field of Inspection Type and Range of
Inspection Standard
BS ISO 2330
BS EN ISO 3691-5:2009
BS EN ISO 3691-5
9 Mobile elevating work
platform (man lift)
Test and Thorough
Examination BS EN 280:2013+A1:2015
10 Access and Working
Scaffolds and Special
Scaffolds
Test and Thorough
Examination BS EN 12811-1:2003
11 Specification for tubes for
use in scaffolding
Test and Thorough
Examination
BS EN 39:2001
BS 1139-1.2:1990
12 Specification for couplers
and fittings for use in
tubular scaffolding
Test and Thorough
Examination BS 1139-2.2:2009+A1:2015
13 Specification for
prefabricated mobile access
and working towers
Test and Thorough
Examination BS EN 1004:2004
14 Specification for
prefabricated steel
splitheads and trestles
Test and Thorough
Examination BS 1139-4:1982
15
Specification for materials,
dimensions, design loads
and safety requirements for
service and working
scaffolds made of
prefabricated elements
Test and Thorough
Examination BS EN 12810-1:2003
16
Specification for
prefabricated tower
scaffolds outside the scope
of BS EN 1004, but utilizing
components from such
systems
Test and Thorough
Examination BS 1139-6:2014
17
Boom Blazer (concrete
pumps) -
Building construction
machinery and equipment.
Concrete pumps. Procedure
Test and Thorough
Examination ISO 21573-2:2008
13
S.NO. Field of Inspection Type and Range of
Inspection Standard
for examination of technical
parameters
18 Code of practice for the safe
use of concrete pumps
Test and Thorough
Examination BS 8476:2007
19 Side Boom pipe layer Test and Thorough
Examination BS 7121-14:2005
20 Cranes for Lifting Persons &
Suspended Baskets
Test and Thorough
Examination
BS 7121- 2- 1:2016
BS EN 14502- 1:2010
21 Jib crane Test and Thorough
Examination BS 7333:1990
22 Runway beams/monorail Test and Thorough
Examination BS 2853:2011
23 Lorry loaders Test and Thorough
Examination BS 7121- 2- 4:2013
24 Chain block/ Chain lever
hoist/Tirfor
Test and Thorough
Examination BS EN 13157-2004+A1:2009
25 Vehicle lifts Test and Thorough
Examination BS EN 1493:2010
26 Offshore Pedestal-mounted
Cranes
Test and Thorough
Examination
API spec 2C
BS EN 13852-1:2013
27 Earthmoving equipment
Safety Part-1: General
requirement
Test and Thorough
Examination
BS EN 474-1:2006 +A5:2018
28 Earth- moving machinery-
Safety Part-2: Requirements
for tractor-Dozers
Test and Thorough
Examination BS EN 474-2:2006+A1:2008
29 Earth- moving machinery-
Safety Part-3: Requirements
for loaders
Test and Thorough
Examination BS EN 474-3 :2006 + A1:2009
30 Earth- moving machinery-
Safety Part-4: Requirements
for backhoe loaders
Test and Thorough
Examination BS EN 474-4:2006 + A2:2012
31 Earth- moving machinery-
Safety Part-5: Requirements
for hydraulic excavators
Test and Thorough
Examination BS EN 474-4:2006+A2:2012
14
S.NO. Field of Inspection Type and Range of
Inspection Standard
32 Earth- moving machinery-
Safety Part-6: Requirements
for Dumpers
Test and Thorough
Examination BS EN 474-6:2006+A1:2009
33 Earth- moving machinery-
Safety Part-7: Requirements
for scrapers
Test and Thorough
Examination BS EN 474-7:2006+A1:2009
34 Earth- moving machinery-
Safety Part-8: Requirements
for Graders
Test and Thorough
Examination BS EN 474-8:2006+A1:2009
35 Earth- moving machinery-
Safety Part-9: Requirements
for pipe layers
Test and Thorough
Examination BS EN 474-9:2006+A1:2009
36 Earth- moving machinery-
Safety Part-10:
Requirements for Trenchers
Test and Thorough
Examination BS EN 474-10:2006+A1:2009
37
Earth - moving machinery-
Safety Part-11:
Requirements for earth and
landfill compactors
Test and Thorough
Examination BS EN 474-11:2006+A1:2008
38
Earth - moving machinery-
Safety Part-12:
Requirements for cable
excavators
Test and Thorough
Examination BS EN 474-12:2006+A1:2008
39 Manual floor crane Test and Thorough
Examination
BS7121-2-1:2016
BS7121-1:2016
40 Pallet stacker Test and Thorough
Examination BS ISO 5766:1990
41 Hand pallet truck Test and Thorough
Examination
BS EN ISO 3691-1:2015
BS EN ISO 3691-3:2016
BS EN ISO 3691-5:2012
42 Tele handler Thorough test and
examination
BS 7121- 2- 1: 2012
BS EN 1459-1:2017
BS EN 15830:2012
43 Man raiding winch Thorough test and
examination
"BS EN 14492-1:2006+A1:2009
BS EN 14492-2:2006 +A1:2009
15
S.NO. Field of Inspection Type and Range of
Inspection Standard
44 Life boat davits/ Life raft
davits
Thorough test and
examination
BS ISO15516:2006
BS ISO13122:2011
45 Electric power hoist Thorough test and
examination
BS EN 14492-1:2006+A1:2009
BS EN 14492-2:2006 +A1:2009
46 Pneumatic power hoist Test and Thorough
Examination
BS EN 14492-1:2006+A1:2009
BS EN 14492-2:2006 +A1:2009
47 General purpose floor
mounted winch
Test and Thorough
Examination
BS EN 14492-1:2006+A1:2009
BS EN 14492-2:2006 +A1:2009
48 Port Cranes (RTG –Rubber
tire gantry), Ship to shore
crane (STS)
Test and Thorough
Examination BS 7121- 2- 7: 2012
49 Self-Climbing system Test and Thorough
Examination BS EN 1495:1997+A2:2009
50 A-Frame Gantry Test and Thorough
Examination BS 5744
16
A-2 Lists of lifting Accessories
S.NO. Field of Inspection Type and Range of
Inspection
Standard
1 Chain Sling-Short link chain for
lifting purposes: Safety-
General conditions of
acceptance
Test and Thorough
Examination
BS EN 818- 1 + A1
2 Short link chain for lifting
purposes: Safety- Medium
tolerance chain for chain slings
(Grade 8)
Test and Thorough
Examination
BS EN 818- 2 + A1
3 Short link chain for lifting
purposes: Safety- Medium
tolerance chain for chain slings
(Grade 4)
Test and Thorough
Examination
BS EN 818- 3 + A1
4 Short link chain for lifting
purposes: Safety- Chain
slings(Grade 8)
Test and Thorough
Examination
BS EN 818- 4 + A1
5 Short link chain for lifting
purposes: Safety- Chain
slings(Grade 4)
Test and Thorough
Examination
BS EN 818- 4 + A1
6 Short link chain for lifting
purposes: Safety- Chain
slings(Grade 4)
Test and Thorough
Examination
BS EN 818- 5 + A1
7 Short link chain for lifting
purposes: Safety- Chain slings-
Specification for information
for use and maintenance to be
provided by the manufacturer
Test and Thorough
Examination
BS EN 818- 6 + A1
8 Short link chain for lifting
purposes: Safety- Fine tolerance
hoist chain- Grade T (Types T,
DAT and DT)
Test and Thorough
Examination
BS EN 818- 7 + A1
9 Shackle Test and Thorough
Examination
BS EN 13889 + A1
10 Components for slings-Safety-
Part 1: Forged steel components
(Grade 8)
Test and Thorough
Examination
BS EN 1677- 1 + A1
17
S.NO. Field of Inspection Type and Range of
Inspection
Standard
11 Components for slings: Safety-
Part-2:Forged steel lifting
hooks with latch (Grade 8)
Test and Thorough
Examination
BS EN 1677- 2 + A1
12 Components for slings: Safety-
Part-3: Forged steel self-locking
hooks (Grade 8)
Test and Thorough
Examination
BS EN 1677- 3 + A1
13 Components for slings: Safety-
Part-4: Links (Grade 8)
Test and Thorough
Examination
BS EN 1677- 4 + A1
14 Components for slings-Safety-
Part-5: Forged steel lifting
hooks with latch (Grade 4)
Test and Thorough
Examination
BS EN 1677- 5 + A1
15 Components for slings-Safety-
Part-6: Links (Grade 4)
Test and Thorough
Examination
BS EN 1677- 6 + A1
16 Wire Rope Sling-Steel wire rope
slings-Safety —Part 1: Slings
for general lifting service
Test and Thorough
Examination
BS EN 13414- 1 + A2
17 Steel wire rope slings —Safety -
Part 2: Specification for
information for use and
maintenance to be provided by
the manufacturer
Test and Thorough
Examination
BS EN 13414- 2 + A2
18 Steel wire rope slings —Safety
—Part 3: Grommets and cable-
laid slings
Test and Thorough
Examination
BS EN 13414- 1: 2003 + A2:
2008
19 Textile slings (web & round) Test and Thorough
Examination
BS EN 1492- 1 + A1
BS EN 1492- 2 + A1
20 Eyebolt Test and Thorough
Examination
BS EN ISO 3266:2010 + A1
21 Spreader beam / lifting beam Test and Thorough
Examination
BS EN 13155 + A2
22 Hooks-Components for slings-
Safety- Part 1: Forged steel
components (Grade 8)
Test and Thorough
Examination
BS EN 1677- 1 + A1
23 Components for slings: Safety-
Part-2:Forged steel lifting
hooks with latch (Grade 8)
Test and Thorough
Examination
BS EN 1677- 2 + A1
18
S.NO. Field of Inspection Type and Range of
Inspection
Standard
24 Components for slings: Safety-
Part-3: Forged steel self-locking
hooks (Grade 8)
Test and Thorough
Examination
BS EN 1677- 3 + A1
25 Components for slings: Safety-
Part-4: Links (Grade 8)
Test and Thorough
Examination
BS EN 1677- 4 + A1
26 Components for slings-Safety-
Part-5: Forged steel lifting
hooks with latch (Grade 4)
Test and Thorough
Examination
BS EN 1677- 5 + A1
27 Components for slings-Safety-
Part-6: Links (Grade 4)
Test and Thorough
Examination
BS EN 1677- 6 + A1
28 Magnet lifting Test and Thorough
Examination
BS EN 13155 + A2
29 Vacuum lifters Test and Thorough
Examination
BS EN 13155 + A2
30 Pad Eyes Test and Thorough
Examination
BS EN ISO 10855-1:2018
BS EN ISO 10855-3:2018
31 Jacks (hydraulic/ pneumatic) Test and Thorough
Examination
BS EN 1494:2000+A1:2008
32 Offshore containers and
associated lifting sets. Periodic
inspection, examination and
testing
Test and Thorough
Examination
BS EN ISO 10855-1:2018
BS EN ISO 10855-3:2018
BS EN ISO 10855-2:2018
33 Clamps (plate and beam) Test and Thorough
Examination
BSEN 13155 2003+A2 2009
34 Beam trolley Test and Thorough
Examination
BS EN 13157
35 Fall arrestor Test and Thorough
Examination
BS EN 353-1
BS EN 353-2
BS EN 360
36 Full body harness Test and Thorough
Examination
BS EN 361
37 Rigging screws (turnbuckles) Test and Thorough
Examination
BS 4429
38 Cargo nets Test and Thorough
Examination
BS 6756
39 Flexible intermediate bulk
container (FIBC)
Test and Thorough
Examination
BS EN ISO 21898
BS EN ISO 21898:2005
19
S.NO. Field of Inspection Type and Range of
Inspection
Standard
40 Pulley Blocks Test and Thorough
Examination
BS EN 13157:2004+A1:2009
41 Inertia Reel Test and Thorough
Examination
BS EN 353-1
BS EN 353-2
BS EN 360
42 Personal rescue tripod Test and Thorough
Examination
BS EN 1496
BS EN 795
43 Man basket/frog carrier Test and Thorough
Examination
BS EN 14502-1:2010
BS EN ISO 10855-1:2018
BS EN ISO 10855-3:2018
20
Appendix B - Lifting Examiners Guide Document reference: 066
21
Lifting Examiners Guide Document reference: 066
Published by the LIFTING EQUIPMENT ENGINEERS ASSOCIATION
3 Osprey Court, Kingfisher Way Hinchingbrooke Business Park
Huntingdon PE29 6FN United Kingdom
Tel: + 44 (0) 1480 432801 Fax: + 44 (0) 1480 436314 E-mail: [email protected] Website: www.leeaint.com
22
CONTENTS 1.0 Introduction Page 1 2.0 Electric Overhead Travelling Cranes Page 2 2.1 EOTC Defined Scope of Thorough Examination Page 3 3.0 Hand Chain Blocks Page 4 3.1 Hand Chain Blocks Defined Scope of Thorough Examination Page 5 4.0 Hand Operated Lever Hoist Page 6 4.1 Hand Operated Lever Hoist Defined Scope of Thorough Examination Page 7 5.0 Jaw Winch Page 8 5.1 Jaw Winch Defined Scope of Thorough Examination Page 9 6.0 Power Operated Hoists Page 10 6.1 Power Operated Hoists Defined Scope of Thorough Examination Page 11 7.0 Winches Page 12 7.1 Winches Defined Scope of Thorough Examination Page 13 8.0 Travelling Girder Trolleys Page 14 8.1 Travelling Girder Trolleys Defined Scope of Thorough Examination Page 15 9.0 Beam Clamps Page 16 9.1 Beam Clamps Defined Scope of Thorough Examination Page 17 10.0 Slewing Jib Cranes Page 18 10.1 Slewing Jib Cranes Defined Scope of Thorough Examination Page 19 11.0 Runways Page 20 11.1 Runways Defined Scope of Thorough Examination Page 21 12.0 Mobile Gantries Page 22 12.1 Mobile Gantries Defined Scope of Thorough Examination Page 23 13.0 Jacks Page 24 13.1 Jacks Defined Scope of Thorough Examination Page 25 14.0 Chain Slings Page 26 14.1 Chain Slings Defined Scope of Thorough Examination Page 27 15.0 Wire Rope Slings Page 28 15.1 Wire Rope Slings Defined Scope of Thorough Examination Page 29 16.0 Flat Woven Webbing Slings Page 30 16.1 Flat Woven Webbing Slings Defined Scope of Thorough Examination Page 31
23
17.0 Man-made Fibre Roundslings Page 32 17.1 Man-made Fibre Roundslings Defined Scope of Thorough Examination Page 33 18.0 Fibre Rope Slings Page 34 18.1 Fibre Rope Slings Defined Scope of Thorough Examination Page 35 19.0 Shackles Page 36 19.1 Shackles Defined Scope of Thorough Examination Page 37 20.0 Eyebolts Page 38 20.1 Eyebolts Defined Scope of Thorough Examination Page 39 21.0 Lifting Beams, Spreaders and Frames Page 40 21.1 Lifting Beams, Spreaders and Frames Defined Scope of Thorough Examination Page 41 22.0 Plate Handling Clamps Page 42 22.1 Plate Handling Clamps Defined Scope of Thorough Examination Page 43 23.0 Rigging Screws & Turnbuckles Page 44 23.1 Rigging Screws & Turnbuckles Defined Scope of Thorough Examination Page 45 24.0 Barrel Lifters Page 46 24.1 Barrel Lifters Defined Scope of Thorough Examination Page 47 25.0 Crane Forks Page 48 25.1 Crane Forks Defined Scope of Thorough Examination Page 49 26.0 Magnetic Lifters Page 50 26.1 Magnetic Lifters Defined Scope of Thorough Examination Page 51 27.0 Vacuum Lifters Page 52 27.1 Vacuum Lifters Defined Scope of Thorough Examination Page 53 28.0 C Hooks Page 54 28.1 C Hooks Defined Scope of Thorough Examination Page 55
24
1.0 Introduction This pocket guide should be used for guidance purposes only. It’s been developed as an aide memoir to the lifting examiner on site and provides a generic defined scope of thorough examination for common standard forms of lifting equipment. In this document we refer to the safe working load; this should be marked on the lifting equipment and it refers to the maximum load as assessed by a competent person which an item of lifting equipment may raise, lower or suspend under particular service conditions. To avoid confusion, the working load limit will be defined as the maximum load to be lifted that an item of lifting equipment is designed to raise, lower or suspend. By way of explanation, the working load limit is the load value assigned to the maximum safe working load under ideal conditions (by calculation), and in most cases the working load limit and the safe working load will be the same. However, depending upon the conditions of use, it may be necessary for the competent person to reduce this to a lower safe working load and it is in these cases that the working load limit and the safe working load will differ. For the purposes of this guidance document we will only use the term safe working load although the reader should be aware it may also refer to the working load limit. The CE marking is stylised mark affixed to an item by the manufacturer, or other responsible person to
signify that the equipment complies with all relevant European Directives.
Page 1
25
2.0 Electric Overhead Travelling Cranes
Page 2
26
2.1 Electric Overhead Travelling Cranes Defined Scope of Thorough Examination
The following components should be included in the defined scope of thorough examination for an Electric Overhead Crane. Note - This list is not exhaustive.
ls, axles, bearings and brakes
along the double girder bridge
anism, this should include the motor, the brake, couplings, gearbox, drum and bearings. The gearbox should be properly lubricated
block and hooks for distortion, corrosion and wear
orage point and the winch drum
that may pose a safety threat
the down shop conductor system
s and buttons are identifiable
ls are functioning as intended
ning correctly (if applicable)
rates correctly (if applicable)
switches are working correctly
signs of damage and corrosion
rity of the crane installation
signs of damage and corrosion
signs of damage and corrosion
Page 3
27
3.0 Hand Chain Blocks
Page 4
Top Hook
Cover
Load Hook
Hand Chain
Load Chain
End Stops
Chain Striper
Pinion Shaft
Ratchet Wheel
Hand Chain Wheel Brake Hub
Drive Gear
28
3.1 Chain Block Defined Scope of Thorough Examination
The following components should be included in the defined scope of thorough examination for a Chain Block. Note - This list is not exhaustive.
r
ta, measurements should be taken and a maximum allowance of 8% wear is recommended
hain
Page 5
29
4.0 Hand Operated Lever Hoist
Page 6
Top Hook
Bottom Hook
Load Chain
Lever
Pocketed Load Wheel
Pinion Shaft Brake Hub
Hand Wheel
Ratchet Wheel
Drive Gear
Chain Striper Change Over Gear
30
4.1 Lever Hoist Defined Scope of Thorough Examination The following components should be included in the defined scope of thorough examination for a Lever Hoist. Note - This list is not exhaustive.
first layer and top layer
k for distortion, wear, cracks and gouges
taken and a maximum allowance of 8% wear is recommended
osion
and properly lubricated
Page 7
31
5.0 Jaw Winches
Page 8
Markings Shear Pins
Operating Levers
Rope Release Anchorage
Casing
Rope Termination
Rope Guide
32
5.1 Jaw Winch Defined Scope of Thorough Examination The following components should be included in the defined scope of thorough examination for Jaw Winches. Note - This list is not exhaustive.
eck for opening of the throat
from the rope guide
eck hydraulic operating lines for wear
Page 9
33
6.0 Power Operated Hoists
Pneumatic Hoist
Electric Hoist
Page 10
Supply Hose
Pendant Controlled
Motor
Trolley
Chain
Bottom Hook
Bottom Hook
Pendant Controlled
Motor
34
6.1 Power Operated Hoists Defined Scope of Thorough Examination
The following components should be included in the defined scope of thorough examination for Power Operated Hoists. Note - This list is not exhaustive.
Check for end stops or slack end anchorage
eck the working set limits are working appropriately
ses for damage, leaks or ice formation
Page 11
35
7.0 Winches
Manual Winch
Electric Winch
Pneumatic Winch
Page 12
36
7.1 Winches Defined Scope of Thorough Examination The following components should be included in the defined scope of thorough examination for Winches. Note - This list is not exhaustive.
distortion, kinks, wear or corrosion
throat
e brake.
tor for any defects, damage or incorrect operation
Page 13
37
8.0 Travelling Girder Trolleys
Manual hand pushed trolley
Geared trolley with anti-tilt device
Page 14
Load Bar
Side Plates
Hand Chain
Load suspension
point
Anti Tilt
Anti-drop
Trolley wheel
Treads and Flanges Wheels, axles, gears,
bearings, and bushes
Markings
38
8.1 Travelling Girder Trolleys Defined Scope of Thorough Examination The following components should be included in the defined scope of thorough examination for Travelling Girder Trolleys. Note - This list is not exhaustive.
marking of the safe working load
ley
-tilt devices have been adjusted
connection of the security between the chain hoist and the trolley
Page 15
39
9.0 Beam Clamps
Adjustable Beam Clamp
Non-adjustable Beam Clamp
Page 16
40
9.1 Beam Clamps Defined Scope of Thorough Examination The following components should be included in the defined scope of thorough examination for Beam Clamps. Note - This list is not exhaustive. The marking should be either by means of a suitable metal tab permanently attached or by stamping, provided that no mechanical property of the clamp is significantly impaired.
representative
e gripping range mark
equipment or 50 kg whichever is the less
recommended
ect nuts and bolts are used for the locking arrangements
maximum allowance of 8% wear is recommended
Page 17
41
10.0 Slewing Jib Cranes
Page 18
Over braced configuration King Post
Slewing Jib Arm
Hoist
Foundation Bolts
42
9.1 Slewing Jib Cranes Defined Scope of Thorough Examination
The following components should be included in the defined scope of thorough examination for Slewing Jib Cranes. Note - This list is not exhaustive.
rer and, if appropriate, the supplier
nstalled and tightened
f the load runs away from the jib arm. These are indications of overloading
ck that the slewing jib arm has a certificate of test loading
age (if applicable)
Page 19
43
11.0 Runways
Free standing runway structure
Page 20
44
11.1 Runways Defined Scope of Thorough Examination The following components should be included in the defined scope of thorough examination for Runways. Note - This list is not exhaustive.
s and taper washers (if applicable)
wheels
and bent or distorted base plates
ase of built in runways, check for any signs of cracking walls or crumbling brickwork
surface of the track should be clean from contaminants such as dirt or debris
Page 21
45
12.0 Mobile Gantries
A frame mobile gantry
Goalpost gantry supporting a beam and a powered hoist
Page 22
46
12.1 Mobile Gantries Defined Scope of Thorough Examination The following components should be included in the defined scope of thorough examination for Mobile Gantries. Note - This list is not exhaustive.
ers
structural members pivot
bent axles, seized bearings and collapsed housing
ich should prevent movement of the wheel. Similarly, rotational locks must prevent the castor from swivelling.
pporting members for signs of deformation, check the bracing, tie bars and lateral stifening members for signs of damage, distortion or deformation
nd twisted web.
Page 23
47
13.0 Jacks
Mechanical Jack
Hydraulic Jack
Page 24
48
13.1 Jacks Defined Scope of Thorough Examination The following components should be included in the defined scope of thorough examination for Jacks. Note - This list is not exhaustive.
signed to carry throughout the whole stroke
base of the jack is not twisted or bent preventing the jack from sitting solidly on the floor
of the seals and other load bearing components
no jerking and the ram should fully retract when the process is over. Important to note that hydraulic rams retract by gravity, so once it has lowered the movement of the ram will slow considerably
of the jack
load bearing components.
or cracks and damage
Page 25
49
14.0 Chain Slings
Two leg sling
Single leg sling
Page 26
50
14.1 Chain Slings Defined Scope of Thorough Examination The following components should be included in the defined scope of thorough examination for Chain Slings. Note - This list is not exhaustive. These should be on a substantial metal tag or label permanently attached to the master link or to a link immediately adjacent to it. The information may also be marked on the master link provided that its mechanical properties are not impaired.
s
es to the vertical (if applicable)
cessive corrosion and heat discoloration of the chain
Page 27
51
15.0 Wire Rope Slings
Two leg sling
Single leg sling
Terminal Fittings
Page 28
Markings
Thimble
Tapered Ferrule
52
15.1 Wire Rope Slings Defined Scope of Thorough Examination The following components should be included in the defined scope of thorough examination for Wire Rope Slings. Note - This list is not exhaustive. Markings should be by means of a suitable plate, preferably in a low stress area. If the marking is in a load-bearing part of the ferrule or master link, care should be taken to ensure that the mechanical properties of the ferrule or link are not impaired.
of leg slings
Check the ferrule for signs of corrosion and cracking
or wear and compare dimensions against the manufacturers data, measurements should be taken and a maximum allowance of 8% wear is recommended
-service is compatible with the rope manufacturing lubricant
Page 29
53
16.0 Flat Woven Webbing Slings
Choke Hitch
Parallel Basket Hitch
Basket Hitch (0-45° to vertical)
Page 30
54
16.1 Flat Woven Webbing Slings Defined Scope of Thorough Examination
The following components should be included in the defined scope of thorough examination for Flat Woven Webbing Slings. Note - This list is not exhaustive.
it passes through terminal fittings as this is a point of high wear.
ensions against the manufacturers data, measurements should be taken and a maximum allowance of 8% wear is recommended
heck there is no damage to the stitching or any looseness of the threads
adation
causing internal abrasion
Page 31
55
17.0 Man-made Fibre Roundslings
Choke Hitch
Parallel Basket Hitch
Basket Hitch (0-45° to vertical)
Page 32
56
17.1 Man-made Fibre Roundslings Defined Scope of Thorough Examination The following components should be included in the defined scope of thorough examination for Man-made Fibre Roundslings. Note - This list is not exhaustive. The information shall be marked both legibly and indelibly, on a durable label fixed directly onto the roundsling. It shall be marked in a type size of not less than 1.5mm in height. A section of the label shall be stitched under the cover which shall also be marked with this information for reference purposes.
evant standard marking
the manufacturers data, measurements should be taken and a maximum allowance of 8% wear is recommended
abrasion
signs of chemical damage. In an advanced state, surface powdering could occur or loss of colouring of the outer cover
Page 33
57
18.0 Fibre Rope Slings
Single leg sling
Page 34
Thimble
Soft eye
58
18.1 Fibre Rope Slings Defined Scope of Thorough Examination The following components should be included in the defined scope of thorough examination for Fibre Rope Slings. Note - This list is not exhaustive. The marking shall be in a type size of no less than 1.5mm in height. One suitable method for applying the marking is to inscribe the details onto a plastic sleeve threaded on the rope and shrunk to it, with a clear plastic sleeve shrunk over the marked sleeve to protect it from soiling.
working load mark
ecifying the number of leg slings
mbles for cracks or deformation
not cause for concern unless it becomes excessive
areas of abrasion
he fibre
-violet radiation
Page 35
59
19.0 Shackles
Bow Shackle
Dee Shackle
Correctly marked HTS Shackle
Page 36
Body
Crown
Bearing Points
Pin
Jaw Opening
Grade
Traceability Code
ID
Safety Pin Nut & Bolt
60
19.1 Shackles Defined Scope of Thorough Examination The following components should be included in the defined scope of thorough examination for Shackles. Note - This list is not exhaustive.
for a clear identification mark
he shackle
manner which will not impair the mechanical properties of the pin (if applicable) (13mm in diameter and above)
egibly and indelibly marked with the grade or traceability code (if applicable) (13mm in diameter and below)
be taken and a maximum allowance of 8% wear is recommended
Page 37
61
20.0 Eyebolts
Dynamo Eyebolt
Collared Eyebolt
Swivel Hoist Ring Eyebolt
Page 38
Shank
Area for Marking
Thread Runout
Eye
Thread Runout
Collar
Shank
Eye
Weld
Swivel Hoist
Eye
62
20.1 Eyebolts Defined Scope of Thorough Examination The following components should be included in the defined scope of thorough examination for Eyebolts. Note - This list is not exhaustive. Each eyebolt shall be legibly and permanently marked in a manner that does not impair its mechanical strength. The symbols shall be no less than 3mm in high. In the case of collar and dynamo eyebolts, the symbols shall be marked on raised flat areas positioned on both sides of the lower parts of the eye. In the case of eyebolts with links, the symbols shall be marked on the side of the link.
of the manufacturer and, if appropriate, the supplier
M denotes ISO metric threads, coarse series, including the diameter designation – ‘M24’
BSW denotes BS Whitworth threads, including the thread diameter – ‘𝟏𝟐⁄ BSW’
UNC denotes unified coarse threads, including the accepted UNC thread diameter – ‘𝟏𝟐⁄UNC’
allowance of 8% wear is recommended (if applicable)
link for wear and compare it to the manufacturers data, measurements should be taken and a maximum allowance of 8% wear is recommended (if applicable)
the presence of contaminants
the collar for contaminants or debris (if applicable)
63
Page 39
21.0 Lifting Beams, Spreaders and Frames
H beam with multiple attachment points
Spreader beam
Lifting Frame
64
Page 40
21.1 Lifting Beams, Spreaders and Frames Defined Scope of Thorough Examination The following components should be included in the defined scope of thorough examination for Lifting Beams, Spreaders and Frames. Note - This list is not exhaustive.
ings
or distortion
be taken and a maximum allowance of 8% wear is recommended
on
chain slings, synthetic web slings, plate clamps, hooks, turnbuckles, should all be inspected in accordance with the respective sections of this code
may have dents or localised buckling
es of structural steel sections for signs of damage
Page 41
65
22.0 Plate Handling Clamps
Page 42
Eye
Screws
Casing
Spring
Lever
Teeth
66
22.1 Plate Handling Clamps Defined Scope of Thorough Examination The following components should be included in the defined scope of thorough examination for Plate Handling Clamps. Note - This list is not exhaustive.
ackle is free from distortion
be taken and a maximum allowance of 8% wear is recommended
Page 43
67
23.0 Rigging Screws & Turnbuckles
Turnbuckle with screwed fork terminal fittings
Turnbuckle with screwed trapezoidal
Turnbuckle with screwed eye
Page 44
Locknuts
End Terminations
Internal & external Threads
68
23.1 Rigging Screws & Turnbuckles Defined Scope of Thorough Examination The following components should be included in the defined scope of thorough examination for Rigging Screws & Turnbuckles. Note - This list is not exhaustive.
Mechanisms
e attachment points for wear and compare it to the manufacturers data, measurements should be taken and a maximum allowance of 8% wear is recommended
or signs of corrosion
Rigging Screw with screwed eyes
Page 45
69
24.0 Barrel Lifters
Top gripping barrel lifters
End gripping barrel lifters
Side gripping barrel lifters
Page 46
70
24.1 Barrel Lifters Defined Scope of Thorough Examination The following components should be included in the defined scope of thorough examination for Barrel Lifters. Note - This list is not exhaustive.
e WLL or 50kg, whichever is the less
eye for signs of wear and damage
ck the clamping faces of the lifter for signs of chips and cracks
Page 47
71
25.0 Crane Forks
Page 48
Automatic
Adjustment
Mechanism
Fork Arms
Mas
t
End Terminations Cross Member
Grab Handle
72
25.1 Crane Forks Defined Scope of Thorough Examination The following components should be included in the defined scope of thorough examination for Crane Forks. Note - This list is not exhaustive.
lifter if it exceeds 5% of the WLL or 50kg, whichever is the less
s of wear
points for wear, damage, corrosion and cracking
sits level on the ground
Page 49
73
26.0 Magnetic Lifters
Electro-permanent magnetic lifter
Portable magnetic lifter
Page 50
74
26.1 Magnetic Lifters Defined Scope of Thorough Examination The following components should be included in the defined scope of thorough examination for Magnetic Lifters. Note - This list is not exhaustive.
imum permissible loading mark, this number is based on various parameters such as: the material of the load, thickness, surface and the air gap between the load and the magnet as well as the lifting capacity of the suspension
fting eye for signs of wear and damage, measurements should be taken and a maximum allowance of 8% wear is permitted
nd its state of charge
rs the power supply and provides a warning of at least 10 minutes in length, before the supply reaches the level where the load will be released
he magnet from being switched on again until the battery has reached the minimum level at which the low power warning is not activated
Page 51
75
27.0 Vacuum Lifters
Multi head vacuum lifter with integral vacuum pump
Vacuum lifter with multiple lifting pads
Page 52
76
27.1 Vacuum Lifters Defined Scope of Thorough Examination The following components should be included in the defined scope of thorough examination for Vacuum Lifters. Note - This list is not exhaustive.
y marked if it exceeds 5% of the WLL or 50kg, whichever is the less
warning: ‘Warning – Load must not be lifted above 1.8m’ must be fitted
device must warn the user that the danger range has been reached.
ttings & Mechanisms
the hoses and couplings for signs of leakage
the vacuum systems including the vacuum reservoirs and vacuum pads is in place
or powered type vacuum lifters must function in the event of a power failure
Page 53
77
28.0 C Hooks
C Hook with protective cover
78
28.1 C Hooks Defined Scope of Thorough Examination The following components should be included in the defined scope of thorough examination for C Hooks. Note - This list is not exhaustive.
or a clear Identification mark
of the C-Hook if it exceeds 5% of the WLL or 50kg, whichever is the less
-levelling crane forks, it should be checked for free movement and correct alignment in the unloaded condition
Check that all the nuts, bolts and pinks are secured in such a way that they will not become loose when they are in use
ion
Page 55
79
Appendix C-QCC LE01 (Template)
Certificate of Thorough Examination-Lifting Gears Safe
C-1 Certificate of Thorough Examination –(Lifting Gears Safe)
Date of Through Examination: Date Of Report: Report number:
Refrences(s) Color Code
Name and Address of employer for whom the thorough
examination was made:
Address of premises at which the examination was
made:
Description and identification of the equipment: Safe
working
load(s):
Date of
manufacture if
known:
Date of last
thorough
examination:
Date of Last Proof Load Test: Date of Next Proof Load Test:
Is this this the first examination after installation or
assembly at a new site or location?
If the answer to the above question is YES
Has the equipment been installed
correctly?
Yes No
Yes No
Was the examination carried out:
Within an interval of 6
months?
Within an interval of 12
months?
In accordance with an
examination scheme?
After the occurrence of
exceptional circumstances?
Yes No
Yes No
Yes No
Yes No
Identification of any part found to have a defect which is or could become a danger to persons and a
description of the defect: (If none state NONE)
Is the above a defect which is of immediate danger to persons Yes No
Is the above a defect which is not yet but could become a danger to
persons: (If yes state the date by when)
Yes by:
Particular of any repair, renewal or alteration required to remedy the defect identified above:
Particular of any tests carried out as part of the examination: (if none state NONE)
IS THEIS EQUIPMENT FIR FOR PURPOSE? Yes No
Name & Qualification of person
making this report:
Name of person
authenticating this report:
Latest date by which next thorough
examination must be carries out:
Name and address of employer of persons making and authenticating this report:
80
C-2 (Template)
Certificate of Thorough Examination –(Lifting Gears Unsafe)
Date of Through Examination: Date Of Report: Report number:
Refrences(s) Color Code
Name and Address of employer for whom the thorough
examination was made:
Address of premises at which the examination was
made:
Description and identification of the equipment: Safe
working
load(s):
Date of
manufacture if
known:
Date of last
thorough
examination:
Date of Last Proof Load Test: Date of Next Proof Load Test:
Is this this the first examination after installation or
assembly at a new site or location?
If the answer to the above question is YES
Has the equipment been installed
correctly?
Yes No
Yes No
Was the examination carried out:
Within an interval of 6
months?
Within an interval of 12
months?
In accordance with an
examination scheme?
After the occurrence of
exceptional circumstances?
Yes No
Yes No
Yes No
Yes No
Identification of any part found to have a defect which is or could become a danger to persons and a
description of the defect: (If none state NONE)
Is the above a defect which is of immediate danger to persons Yes No
Is the above a defect which is not yet but could become a danger to
persons: (If yes state the date by when)
Yes by:
Particular of any repair, renewal or alteration required to remedy the defect identified above:
Particular of any tests carried out as part of the examination: (if none state NONE)
IS THEIS EQUIPMENT FIR FOR PURPOSE? Yes No
Name & Qualification of person
making this report:
Name of person
authenticating this report:
Latest date by which next thorough
examination must be carries out:
Name and address of employer of persons making and authenticating this report:
81
Appendix C- QCC LE03 (Template)
Certificate of Through Examination-Defect Report List
Signature: Date:
QCC LE03 Certificate of Through Examination-Defect Report List
Equipment
Identification
Number
Equipment
Description
Identification of
Defective Parts
Is the Defect of
Immediate
Danger
If not Immediate
Danger when will
it become a
Danger without
Rectification
Particulars of Any
Repair, Renewal
or Alternation to
Remedy the
Defects