abu dhabi specification ينفلا يبظوبأ ريياعم · ads 9-2014 4102 - 9 ف أ م. 1 ......
TRANSCRIPT
-
Abu Dhabi Specification أبوظبي الفنية معايير
ضبط الجودة في مختبرات الفحص و المعايرة
Quality Control in Testing and Calibration Laboratories
)مسودة نهائية ( Final draft) )
ADS 9-2014 4102 - 9م أ ف
-
1
Table of Contents Page
About Abu Dhabi Quality and Conformity Council 3
Introduction 3
Scope 3
Acknowledgement 4
Terms and Definitions 5
Application 6
Responsibility 6
General requirements for laboratories 6
Internal quality control 9
External quality assessment scheme 9
Final Provisions 10
Appendix 1 11
-
2
Amendment Page
To ensure that each controlled copy of this ADS contains a complete record of amendments, the
Amendment Page is updated and issued with each set of revised/new pages of the document.
This ADS is a live document which can be amended when necessary. QCC conducts what it
takes to make this document available to all and collects all observations on it. QCC prepares for
a meeting of the Quality Control Laboratories Working Group to discuss the comments made on
the document in order to review and amend it.
Amendment
Discard
Insert
No
Date
*Sections Changed
Page(s)
Issue no
Page(s)
Issue
no
Document launched - - 11 1
-
3
-
4
QCC would like to thank the members of the
Working Group listed below. The membership of the QCC Working Group is as
follows:
Entity Name
Abu Dhabi Health Services Company.
(SEHA)
Dr. Laila Abdel Wareth (chair)
1
Abu Dhabi Health Services Company
(SEHA)
Dr.Eman Alzaabi 2
Abu Dhabi Health Services Company
(SEHA)
Dr. Issam Ateig 3
Health Authority - Abu Dhabi (HAAD) Dr. Fatima ALQahwagi 4
Health Authority - Abu Dhabi (HAAD) Hala Abdulrahman 5
Emirates Authority For standardization
and Metrology (ESMA)
Eng. Mekhled Alzaben 6
Emirates Authority For standardization
and Metrology (ESMA)
Eng. Oraib ALDmour 7
National Reference Laboratory (NRL) Dr. Reem El Bahtimi 8
Central Testing Laboratories (CTL)-
QCC
Dr. Riyad Shareef 9
Intertek Company Eng. Waleed Rusheidat 10
Abu Dhabi Quality and Conformity
Council- QCC
Dr. Rehab Al Ameri 11
Abu Dhabi Quality and Conformity
Council- QCC
Eng. Osama Melhem 12
Abu Dhabi Quality and Conformity
Council- QCC
Eng. Husain Al Bazzi 13
Abu Dhabi General Services
(Musanada)
Eng.Hasan Siraji 14
Abu Dhabi Quality and Conformity
Council- QCC-CTL
Salama AlDhahiri 15
Abu Dhabi Quality and Conformity
Council- QCC-CTL
Maha AlMarzouqi 16
Abu Dhabi Municipality (ADM) Eng.Jamal Al Hadidi 17
Alhoty Laboratories. Anoop Mony 18
Abu Dhabi Quality and Conformity
Council- QCC
Dr. Waill AlOmari
(Coordinator)
19
http://www.seha.ae/seha/enhttp://www.seha.ae/seha/enhttps://www.facebook.com/eman.alzaabi.7?ref=br_rs&fref=browse_searchhttp://www.seha.ae/seha/enhttp://ae.linkedin.com/pub/eng-mekhled-alzaben-esma/62/b57/23http://www.nrl.ae/http://silla.ae/3537/reem-el-bahtimi
-
5
QUALITY CONTROL IN TESTING AND CALIBRATION LABORATORIES
An operation that, under specified conditions, in a first step, establishes
a relation between the quantity values with measurement uncertainties provided by
measurement standards as well as corresponding indications with associated
measurement uncertainties, and in a second step, uses this information to establish
a relation to obtain a measurement result from an indication.
Chain of Traceability: metrological traceability of measurement result where the
metrological reference is the definition of a measurement unit through its practical
realization.
extreme value of measurement error, with respect to a
known reference quantity value, permitted by specifications or regulations for a given
measurement, measuring instrument, or measuring system.
material, sufficiently homogeneous and stable with
reference to specified properties, which has been established to be fit for its
intended use in measurement or in examination of nominal properties.
repeatable calibration checks performed by the laboratory,
at appropriate intervals, to maintain confidence in the calibration status of
measuring and all test equipment’s that affect the measurement results
concerned.
-
6
-
-
-
-
7
-
-
-
-
-
-
8
-
-
-
-
-
9
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
10
-
-
-
-
-
-
11
---
----
-
12
المراجع :
- ISO/IEC 17025 General requirements for the competence of testing and calibration laboratories. - OIML V1: International vocabulary of terms in legal metrology (VIML)
للتنمية الصناعية والتعدينالعربية عليها من قبل المنظمة وترجمته الموافق - - ISO Gguide 34: General requirements for the competence of reference
material producers. - OIML D10: Guidelines for the determination of calibration Intervals of measuring instruments, 2007. - ILAC-G24: Guidelines for the determination of calibration Intervals of
measuring instruments, 2007. - BIPM: Evaluation of Measurement data- Guide to the expression of
Uncertainty in measurement, JCGM 100:2008. - Statistical Quality Control for Quantitative Measurement Procedures:
Principles and Definitions; Approved Guideline-Third Edition.C24-A3 Volume 26 No .25.
- ISO 7870-1:2014, Control Charts-Part 1: General Guidelines. - ISO 7870-2:2013, Control Charts- Part 2: Shewhart Control Charts. - ISO 7870-3:2012, Control Charts- Part 3: Acceptance of Control
Charts. - ISO 7870-4:2011, Control Charts- Part 4, Cumulative Sum Charts. - ISO 7870-5:2014, Control Charts- Part 5, Specialized Control Charts.
بشأن الالئحة التنفيذية لتنظيم 11/6/9002( تاريخ 5/1قرار مجلس إدارة هيئة اإلمارات للمواصفات والمقاييس رقم ) -
( بشأن 9006( لسنة )11( من قرار مجلس الوزراء رقم )16أعمال المقاييس القانونية في الدولة، صادر بموجب المادة ) وتعديالته. الوطني للقياسالنظام
6