TRUNNION MOUNTED BALL VALVE

INSTALLATION, MAINTENANCE, & REPAIR MANUAL

ABC Corporation • 3245 S. HattieOklahoma City, Oklahoma 73129

Telephone: (405) 677-3321 • Fax: (405) 677-3917Email:Balon@balon.com • www.balon.com

ABCMade in USA

2016 Balon Corporation©

ABC Rev.3.01.06.17Page 1

Balon Trunnion Mounted Ball Valve Storage 2Balon Trunnion Mounted Ball Valve Installation 2Balon Trunnion Mounted Ball Valve Operation 2 & 3Balon Trunnion Mounted Ball Valve Maintenance 3Secondary Sealing in Trunnion Mounted Ball Valves 3

WARNING: BEFORE ATTEMPTING TO REPAIR A VALVE THAT HAS BEEN IN SERVICE BE SURE TO BLOCK THE ENDS AND SLOWLY OPEN AND CLOSE THE VALVE TO VENT ANY INTERNAL PRESSURE.

10" through 12" ANSI Class 150 (285 PSI WP) Dimensional Data 410" through 12" ANSI Class 150 (285 PSI WP) Material Description 58" through 12" ANSI Class 300 (740 PSI WP) Dimensional Data 68" through 12" ANSI Class 300 (740 PSI WP) Material Description 74" through 12" ANSI Class 600 (1480 PSI WP) Dimensional Data 84" through 12" ANSI Class 600 (1480 PSI WP) Material Description 94" ANSI Class 900 (2220 PSI WP) Dimensional Data 104" ANSI Class 900 (2220 PSI WP) Material Description 11Balon Contact Information 12

TABLE OF CONTENTS

ABCRev.3.01.06.17

BALON TRUNNION MOUNTED BALL VALVE STORAGEBalon Corporation ships ball valves in the open position. In order to protect valves during shipment, Balon ships trunnion mounted valves in cardboard cartons or wooden boxes. The hand wheels on gear-operated valves are removed and secured to the valves for shipment.

Valves should always be stored in the fully open position and should be kept indoors under clean, dry conditions.

BALON TRUNNION MOUNTED BALL VALVE INSTALLATION

Balon ball valves seal bi-directionally and may be installed in either direction.

Valves should be installed in the open position. Flange end protectors should be left in place while valves are being handled and should not be removed until final installation. Heavy valves should be lifted into position using suitable straps. The straps should be positioned around the conduits near the flanges or through the eye bolts, if provided. The straps should never be positioned around a gear operator, handwheel, or actuator.

Industry accepted make-up practice should be followed when installing flanged end valves.

Trash, such as welding slag, dirt, sand, and other foreign matter, should always be flushed from the line before operating any valve.

Piping systems are often pressure tested prior to being placed in service. Assure that all valves are in the open position during the introduction of the test medium. With valves in the open position or partially open position, valve shell testing may be done at a pressure up to 1.5 times the rated working pressure of the valves. Valves should be kept in the open position or partially open position during shell testing. Valve shell testing should never be done with the valves in the closed position.

With valves in the fully closed position, valve seat testing may be done at pressures up to 1.1 times the rated working pressure of the valves.

With all valves in the fully open position to avoid the entrapment of debris, the pressure test medium should be completely eliminated from the system after testing has been completed. Water that is allowed to remain trapped inside valves can freeze. Water that freezes inside valves can damage the valves and any pipe, fittings, or equipment directly or indirectly connected to the valve.

BALON TRUNNION MOUNTED BALL VALVE OPERATION

A ball valve is designed to be used in the fully open or fully closed position. On gear operated valves, the position indicator is located on the top of the gear box. To open the valve, rotate the handwheel counterclockwise. To close the valve, rotate the handwheel clockwise. Using a ball valve in the partially open position can result in seat damage and, under certain conditions, damage to other valve components or to pipe, fittings, or equipment directly or indirectly connected to the valve. Applying excessive torque in an attempt to turn a ball beyond its 90 degree stop point could damage the valve stops and misalign the ball. A valve should always be operated within the pressure and temperature limits designated by the manufacturer.

Page 2

ABC Rev.3.01.06.17

It is good practice to operate any valve periodically in order to assure that the ball is able to move freely.

The Balon trunnion mounted ball valve is equipped with a body bleed fitting that can be used for draining the body cavity or for performing a double block and bleed procedure. Draining the body can be done with the valve in either the closed or the open position. The double block and bleed procedure must be performed with the valve in the closed position. Locate the bleed fitting and determine the position of the bleed hole. Be aware that fluid and debris will be vented under pressure through this hole. Position yourself and others safely out of line of venting pressure. To prevent the inadvertent removal of the bleed fitting, place a backup wrench on the body of the bleed fitting, assuring that the backup wrench does not cover the bleed hole. With another wrench, carefully and slowly loosen the hex head on the bleed fitting, allowing pressure, fluid, and debris to vent.

Note that a trunnion mounted ball valve can unexpectedly release residual pressure from the body cavity past the downstream seat. Valve users should exercise caution by protecting personnel and equipment from spontaneous pressure release.

WARNING! Under certain circumstances it is possible for trash and debris to effectively plug the body bleed fitting. This can give the false impression that the body cavity is depressurized. Before attempting to dismantle any ball valve, the valve should be opened and closed a complete cycle to assure that there is no pressure trapped within the body cavity.

MAINTENANCE FOR BALON TRUNNION MOUNTED BALL VALVES

Balon trunnion mounted ball valves require no regular maintenance to maintain proper operation and sealing. Balon stems require no adjustment or greasing for proper sealing and operation.

SECONDARY SEALING IN BALON TRUNNION MOUNTED BALL VALVES

Balon trunnion mounted valves are equipped with grease injection fittings that may be used when attempting to restore the seat seal or to deliver grease to the surface of the ball. Grease should be injected into the upstream injection fitting when attempting to restore the seat seal. Always assure the compatibility of injected grease with the valve components and the medium in the line.

Before using grease injection fittings, assure that the valve is in the fully closed position. Each grease fitting is equipped with a protective cap that must be removed before grease can be injected. Place a backup wrench on the body of the injection fitting and, using a separate wrench, carefully remove the protective cap. Never remove the grease fitting from the valve while the valve is under pressure.

Connect a grease gun to the fitting and inject an appropriate volume of grease. If the valve fails to seal after the injection of a reasonable volume of grease, turn the handwheel gently back and forth, moving the ball against the seat in order to assist the spread of the grease over the seat surface and dislodge debris. Then repeat the grease injection procedure.

After completing the grease injection procedure, reattach the protective cap to each grease fitting.

Page 3

ABC Rev.3.01.06.17

BALON TRUNNION MOUNTED BALL VALVE 10" and 12" ANSI CLASS 150 (285 PSI WP)

Page 4

Dimensional Data

SIZE

CATALOG NUMBER

PORT A B C D E F G LBS.STANDARD TRIMCARBON STEEL

BALL & STEM

NACE TRIMCARBON STEELBALL & STEM*

NACE TRIM316 SS

BALL & STEM*

10x10x10 10F-T13-RF 10F-T13CN-RF* 10F-T13SN-RF* 10 21.00 10.5 5.25 13.26 20 13.56 15.25 937.512x12x12 12F-T13-RF 12F-T13CN-RF* 12F-T13SN-RF* 12 24.00 12.00 3.04 18.85 20 11.85 20.60 1481

* NACE Valves are also available in low temp. Call factory for details.

ABC Rev.3.01.06.17

BALON TRUNNION MOUNTED BALL VALVE 10" and 12" ANSI CLASS 150 (285 PSI WP)

Material DescriptionITEM PART NAME STANDARD TRIM CARBON STEEL NACE STAINLESS STEEL NACE

1 Body ASTM A216 WCB/A105 ASTM A216 WCB/A105 ASTM A216 WCB/A1052 Adapter ASTM A216 WCB/A105 ASTM A216 WCB/A105 ASTM A216 WCB/A1053 Ball Carbon Steel

Nickel Chrome PlatedCarbon SteelNickel Chrome Plated

316 Stainless Steel

4 Seat Carrier Carbon SteelNickel Chrome Plated

Carbon SteelNickel Chrome Plated

316 Stainless Steel

5 Seat Insert Nylon/Acetal Nylon/Acetal Nylon/Acetal6 Stem Carbon Steel Carbon Steel 316 Stainless Steel7 Stem O-Ring Buna-N Fluorocarbon Fluorocarbon8 Stem Thrust Washer TFE TFE TFE9 Snap Ring Carbon Spring Steel Carbon Spring Steel Carbon Spring Steel

10 Stem Key Steel Key Stock Steel Key Stock Steel Key Stock11 Seat O-Ring Buna-N Fluorocarbon Fluorocarbon12 Fireseal Graphite Graphite Graphite13 Fireseal Support Ring Stainless Steel Stainless Steel Stainless Steel14 Spring Inconel X-750 Inconel X-750 Inconel X-75015 Body O-Ring Buna-N Fluorocarbon Fluorocarbon16 Bearing Block Carbon Steel Carbon Steel Stainless Steel17 Trunnion Bearing 316 SS/TFE 316 SS/TFE 316 SS/TFE18 Bleed Fitting* 316 Stainless Steel 316 Stainless Steel 316 Stainless Steel19 Sealant Injection Fitting Alloy Steel Alloy Steel Alloy Steel20 Internal Check Fitting 316 Stainless Steel 316 Stainless Steel 316 Stainless Steel21 Nuts ASTM A194 2H ASTM A194 2HM ASTM A194 2HM22 Studs ASTM A193 B7 ASTM A193 B7M ASTM A193 B7M23 Stem Bearing Glass/TFE Glass/TFE Glass/TFE24 Hexhead Capscrew Alloy Steel Alloy Steel Alloy Steel25 Lock Washer Alloy Steel Alloy Steel Alloy Steel26 Adapter Plate Ductile Iron Ductile Iron Ductile Iron27 Capscrews Alloy Steel Alloy Steel Alloy Steel28 Gear Operator Ductile Iron Ductile Iron Ductile Iron29 Handwheel Carbon Steel Carbon Steel Carbon Steel

* 3/8" NPT

Page 5

ABCRev.3.01.06.17

BALON TRUNNION MOUNTED BALL VALVE 8" Through 12" ANSI CLASS 300 (740 PSI WP)

Page 6

Dimensional Data

SIZE

CATALOG NUMBER

PORT A B C D E F G LBS.STANDARD TRIMCARBON STEEL

BALL & STEM

NACE TRIMCARBON STEELBALL & STEM*

NACE TRIM316 SS

BALL & STEM*

8x8x8 8F-T33-RF 8F-T33CN-RF* 8F-T33SN-RF* 8 19.75 9.37 5.25 11.75 20 11.56 13.67 68410x10x10 10F-T33-RF 10F-T33CN-RF* 10F-T33SN-RF* 10 22.38 11.2 3.04 17.83 20 13.25 19.57 120012x12x12 12F-T33-RF 12F-T33CN-RF* 12F-T33SN-RF* 12 25.50 12.75 3.04 18.85 20 11.85 20.60 1670

* NACE Valves are also available in low temp. Call factory for details.

ABC Rev.3.01.06.17Page 7

BALON TRUNNION MOUNTED BALL VALVE 8" Through 12" ANSI CLASS 300 (740 PSI WP)

Material DescriptionITEM PART NAME STANDARD TRIM CARBON STEEL NACE STAINLESS STEEL NACE

1 Body ASTM A216 GR WCB/A105 ASTM A216 GR WCB/A105 ASTM A216 WCB/A1052 Adapter ASTM A216 WCB/A105 ASTM A216 WCB/A105 ASTM A216 WCB/A1053 Ball Carbon Steel

Nickel Chrome PlatedCarbon SteelNickel Chrome Plated

316 Stainless Steel

4 Seat Carrier Carbon SteelNickel Chrome Plated

Carbon SteelNickel Chrome Plated

316 Stainless Steel

5 Seat Insert Nylon/Acetal Nylon/Acetal Nylon/Acetal6 Stem Carbon Steel Carbon Steel 316 Stainless Steel7 Stem O-Ring Buna-N Fluorocarbon Fluorocarbon8 Stem Thrust Washer TFE TFE TFE9 Snap Ring Carbon Spring Steel Carbon Spring Steel Carbon Spring Steel

10 Stem Key Steel Key Stock Steel Key Stock Steel Key Stock11 Seat O-Ring Buna-N Fluorocarbon Fluorocarbon12 Fireseal Graphite Graphite Graphite13 Fireseal Support Ring Stainless Steel Stainless Steel Stainless Steel14 Spring Inconel X-750 Inconel X-750 Inconel X-75015 Body O-Ring Buna-N Fluorocarbon Fluorocarbon16 Bearing Block Carbon Steel Carbon Steel Stainless Steel17 Trunnion Bearing 316 SS/TFE 316 SS/TFE 316 SS/TFE18 Bleed Fitting* 316 Stainless Steel 316 Stainless Steel 316 Stainless Steel19 Sealant Injection Fitting Alloy Steel Alloy Steel Alloy Steel20 Internal Check Fitting 316 Stainless Steel 316 Stainless Steel 316 Stainless Steel21 Nuts ASTM A194 2H ASTM A194 2HM ASTM A194 2HM22 Studs ASTM A193 B7 ASTM A193 B7M ASTM A193 B7M23 Stem Bearing Glass/TFE Glass/TFE Glass/TFE24 Hexhead Capscrew Alloy Steel Alloy Steel Alloy Steel25 Lock Washer Alloy Steel Alloy Steel Alloy Steel26 Adapter Plate Ductile Iron Ductile Iron Ductile Iron27 Capscrews Alloy Steel Alloy Steel Alloy Steel28 Gear Operator Ductile Iron Ductile Iron Ductile Iron29 Handwheel Carbon Steel Carbon Steel Carbon Steel

* 3/8" NPT

ABCRev.3.01.06.17 Page 8

BALON TRUNNION MOUNTED BALL VALVE 4" THROUGH 12" ANSI CLASS 600 (1480 PSI WP)

Dimensional Data

SIZE

CATALOG NUMBER

PORT

A B

C D E F G LBS.STANDARD TRIMCARBON STEEL

BALL & STEM

NACE TRIMCARBON STEEL

BALL & STEM

NACE TRIM316 SS

BALL & STEM RF RTJ RF RTJ

4x4x4 4F-T63 4F-T63CN* 4F-T63SN* 4 17 17.12 9 8.56 3.04 8.06 13 8.75 9.68 3096x6x6 6F-T63 6F-T63CN* 6F-T63SN* 6 22 22.12 11 11.06 4.06 9.69 20 11.19 11.31 5608x8x8 8F-T63 8F-T63CN* 8F-T63SN* 8 26 26.12 13 13.06 5.25 11.75 20 11.56 13.68 998

10x10x10 10F-T63 10F-T63CN* 10F-T63SN* 10 31 31.12 15.5 15.56 3.038 17.82 26 14.00 19.57 155012x12x12 12F-T63 12F-T63CN* 12F-T63SN* 12 33 33.12 16.5 16.56 3.04 18.53 26 14.00 20.28 2320

ABC Rev.3.01.06.17Page 9

BALON TRUNNION MOUNTED BALL VALVE 4" THROUGH 12" ANSI CLASS 600 (1480 PSI WP)

Material DescriptionITEM PART NAME STANDARD TRIM CARBON STEEL NACE STAINLESS STEEL NACE

1 Body ASTM A216 WCB/A105 ASTM A216 WCB/A105 ASTM A216 WCB/A1052 Adapter ASTM A216 WCB/A105 ASTM A216 WCB/A105 ASTM A216 WCB/A1053 Ball Carbon Steel

Nickel Chrome PlatedCarbon SteelNickel Chrome Plated

316 Stainless Steel

4 Seat Carrier Carbon SteelNickel Chrome Plated

Carbon SteelNickel Chrome Plated

316 Stainless Steel

5 Seat Insert Nylon/Acetal Nylon/Acetal Nylon/Acetal6 Stem Carbon Steel Carbon Steel 316 Stainless Steel7 Stem O-Ring Buna-N Fluorocarbon Fluorocarbon8 Stem Thrust Washer TFE TFE TFE9 Snap Ring Carbon Spring Steel Carbon Spring Steel Carbon Spring Steel

10 Stem Key Steel Key Stock Steel Key Stock Steel Key Stock11 Seat O-Ring Buna-N Fluorocarbon Fluorocarbon12 Fireseal Graphite Graphite Graphite13 Fireseal Support Ring Stainless Steel Stainless Steel Stainless Steel14 Spring Inconel X-750 Inconel X-750 Inconel X-75015 Body O-Ring Buna-N Fluorocarbon Fluorocarbon16 Bearing Block Carbon Steel Carbon Steel Stainless Steel17 Trunnion Bearing 316 SS/TFE 316 SS/TFE 316 SS/TFE18 Spacer Block Stainless Steel Stainless Steel Stainless Steel19 Bleed Fitting* 316 Stainless Steel 316 Stainless Steel 316 Stainless Steel20 Sealant Injection Fitting Alloy Steel Alloy Steel Alloy Steel21 Internal Check Fitting 316 Stainless Steel 316 Stainless Steel 316 Stainless Steel22 Nuts ASTM A194 2H ASTM A194 2HM ASTM A194 2HM23 Studs ASTM A193 B7 ASTM A193 B7M ASTM A193 B7M24 Stem Bearing Glass/TFE Glass/TFE Glass/TFE25 Hexhead Capscrew Alloy Steel Alloy Steel Alloy Steel26 Lock Washer Alloy Steel Alloy Steel Alloy Steel27 Adapter Plate Ductile Iron Ductile Iron Ductile Iron28 Capscrews Alloy Steel Alloy Steel Alloy Steel29 Gear Operator Ductile Iron Ductile Iron Ductile Iron30 Handwheel Carbon Steel Carbon Steel Carbon Steel

* 3/8" NPT

ABC Rev.3.01.06.17

* NACE Valves are also available in low temp. Call factory for details.

Dimensional Data

SIZE

CATALOG NUMBER

PORT

A B

C D E F G LBS.STANDARD TRIMCARBON STEEL

BALL & STEM

NACE TRIMCARBON STEEL

BALL & STEM

NACE TRIM316 SS

BALL & STEM RF RTJ RF RTJ

4x4x4 4F-T93 4F-T93CN* 4F-T93SN* 4 18 18.12 9 9.06 3.04 8.06 13 8.75 9.68 331

BALON TRUNNION MOUNTED BALL VALVE 4" ANSI CLASS 900 (2220 PSI WP)

Page 10

ABC Rev.3.01.06.17

Material DescriptionITEM PART NAME STANDARD TRIM CARBON STEEL NACE STAINLESS STEEL NACE

1 Body ASTM A216 WCB/A105 ASTM A216 WCB/A105 ASTM A216 WCB/A1052 Adapter ASTM A216 WCB/A105 ASTM A216 WCB/A105 ASTM A216 WCB/A1053 Ball Carbon Steel

Nickel Chrome PlatedCarbon SteelNickel Chrome Plated

316 Stainless Steel

4 Seat Carrier Carbon SteelNickel Chrome Plated

Carbon SteelNickel Chrome Plated

316 Stainless Steel

5 Seat Insert Nylon/Acetal Nylon/Acetal Nylon/Acetal6 Stem Carbon Steel Carbon Steel 316 Stainless Steel7 Stem O-Ring Buna-N Fluorocarbon Fluorocarbon8 Stem Thrust Washer TFE TFE TFE9 Snap Ring Carbon Spring Steel Carbon Spring Steel Carbon Spring Steel

10 Stem Key Steel Key Stock Steel Key Stock Steel Key Stock11 Seat O-Ring Buna-N Fluorocarbon Fluorocarbon12 Fireseal Graphite Graphite Graphite13 Fireseal Support Ring Stainless Steel Stainless Steel Stainless Steel14 Spring Inconel X-750 Inconel X-750 Inconel X-75015 Body O-Ring Buna-N Fluorocarbon Fluorocarbon16 Bearing Block Carbon Steel Carbon Steel Stainless Steel17 Trunnion Bearing 316 SS/TFE 316 SS/TFE 316 SS/TFE18 Spacer Block Stainless Steel Stainless Steel Stainless Steel19 Bleed Fitting* 316 Stainless Steel 316 Stainless Steel 316 Stainless Steel20 Sealant Injection Fitting Alloy Steel Alloy Steel Alloy Steel21 Internal Check Fitting 316 Stainless Steel 316 Stainless Steel 316 Stainless Steel22 Nuts ASTM A194 2H ASTM A194 2HM ASTM A194 2HM23 Studs ASTM A193 B7 ASTM A193 B7M ASTM A193 B7M24 Stem Bearing Glass/TFE Glass/TFE Glass/TFE25 Hexhead Capscrew Alloy Steel Alloy Steel Alloy Steel26 Lock Washer Alloy Steel Alloy Steel Alloy Steel27 Adapter Plate Ductile Iron Ductile Iron Ductile Iron28 Capscrews Alloy Steel Alloy Steel Alloy Steel29 Gear Operator Ductile Iron Ductile Iron Ductile Iron30 Handwheel Carbon Steel Carbon Steel Carbon Steel

* 3/8" NPT

BALON TRUNNION MOUNTED BALL VALVE 4" ANSI CLASS 900 (2220 PSI WP)

Page 11

ABC Corporation 3245 S. Hattie

Oklahoma City, Oklahoma 73129 Telephone: (405) 677-3321

Fax: (405) 677-3917

balon@balon.com • www.balon.com

Page 12