a837 disassembly & reassembly
TRANSCRIPT
SAMSUNG Proprietary-Contents may change without notice11-1
This Document can not be used without Samsung's authorization
11. Disassembly and Assembly Instructions
11-1 Disassembly
1) Remove SCREW CAP 2points at REAR. 1) Release SCREW 2points.
1) Puts screw driver in the groove and lift hook. 1) Move along REAR COVER and disjoint hook.
1 2
3 4
1) Be care of the scratch.
SAMSUNG Proprietary-Contents may change without notice
Disassembly and Assembly Instructions
11-2
This Document can not be used without Samsung's authorization
1) After remove REAR COVER release SCREW 3point.1) After open 3points at hook using a decomposition
tool, separate FRONT and REAR.
1) Remove KEYPAD. 1) Release SCREW 4points.
5 6
7 8
SAMSUNG Proprietary-Contents may change without notice
Disassembly and Assembly Instructions
11-3
This Document can not be used without Samsung's authorization
1) Presses PBA with finger at REAR back and separates
PBA in REAR.1) Extract connector by tweezers.
1) Release INTENNA SCREW 2points. 1) Release SHIELD CAN SCREW 3points.
9 10
11 12
SAMSUNG Proprietary-Contents may change without notice
Disassembly and Assembly Instructions
11-4
This Document can not be used without Samsung's authorization
1) Presses shaft by tweezers and separates FRONT and
Folder ASSY.1) Separates FRONT and Folder ASSY.
1) Remove SCREW CAP 6points. 1)Release SCREW 6points.
13 14
15 16
SAMSUNG Proprietary-Contents may change without notice
Disassembly and Assembly Instructions
11-5
This Document can not be used without Samsung's authorization
1) Separates UPPER and LOWER. 1) Remove unelectrical conduction TAPE.
1) Separate CON TO CON in connector. 1) Separate SPAEKER 2ea of LOWER.
17 18
19 20
SAMSUNG Proprietary-Contents may change without notice
Disassembly and Assembly Instructions
11-6
This Document can not be used without Samsung's authorization
1) Separate CON TO CON and Rubber Ring in connector. 1) Motor, RCV, Camera exclusion by tweezers
1) Separates LCD and LOWER. END.
21 22
23 24
SAMSUNG Proprietary-Contents may change without notice
Disassembly and Assembly Instructions
11-7
This Document can not be used without Samsung's authorization
1) After LCD safe arrival, place MOTOR, RECEIVER,
CAMERA safely.1) Insert CON TO CON connector
2) After inserting SPK into LOWER safely, Arrange
wires.1)Attach non-conductive TAPE.
1 2
3 4
11-2 Assembly
SAMSUNG Proprietary-Contents may change without notice
Disassembly and Assembly Instructions
11-8
This Document can not be used without Samsung's authorization
1) Arrange Packing Rubber on each point carefully.1) Assemble UPPER and LOWER.
2) Check whether Packing Rubber is arranged or not.
1) Turn each Screw to the right(6EA). 1) Attach Screw Cap(6EA).
5 6
7 8
SAMSUNG Proprietary-Contents may change without notice
Disassembly and Assembly Instructions
11-9
This Document can not be used without Samsung's authorization
1) Assemble Folder ASSY and Front.
2) Press shaft by tweezers and put it in the front
groove.
1) Turn Antenna Screw to the right(2EA).
1) Turn Shieldcan Screw to the right(3EA). 1) Insert CON-TO-CON to PBA connector
9 10
1) Take care about tearing CON-TO-CON FPCB
11 12
SAMSUNG Proprietary-Contents may change without notice
Disassembly and Assembly Instructions
11-10
This Document can not be used without Samsung's authorization
1) First, give a slope to the PBA leaning IF connector
and then put down PBA in Rear.
1) Turn PBA Screw to the right(4EA).
1) Put down the KEYPAD.
2) Press the KEYPAD wholly to seal the Rear.
1) First, hook the Front on the left side of Rear(2
point.) and then right side of Rear(2 point).
2) Finally, hook it on bottom of Rear.(1 point).
13 14
15 16
SAMSUNG Proprietary-Contents may change without notice
Disassembly and Assembly Instructions
11-11
This Document can not be used without Samsung's authorization
1) Turn Rear Screw to the right(3EA).1) After Assemble Rear Cover, Turn Screw to the
right(2EA).
1) Insert Screw Cap(2EA).
17 18
19