a. general clarifications - clinton county, iowa · 4. window types 26 and 28 are replacing windows...

DOCUMENT 00 0492 VE COORDINATION ADDENDUM NO. 2

Clinton County Justice Center – Bid Package #4 VE Coordination CDs

VE Coordination Addendum # 2/ August 8, 2017 416315-0

00 0492-1

DATE: August 8, 2017 PROJECT NAME: Clinton County Justice Center – Bid Package #4 VE Coordination CDs This Addendum forms a part of the bidding and contract documents. This Addendum supersedes and supplements all portions of the original bidding and contract documents dated, July 14, 2017 and Addendum #1 issued July 27, 2017, with which it conflicts. ACKNOWLEDGE RECEIPT OF THIS ADDENDUM IN THE SPACE PROVIDED ON THE BID FORM. FAILURE TO DO SO MAY SUBJECT THE BIDDER TO DISQUALIFICATION.

A. GENERAL CLARIFICATIONS

1. Footings for the building will be complete before installation of underground conduits. The contractor is responsible for including in the bid core drilling of foundations to install conduits.

2. Clinton County Justice Center is tax exempt. Awarded contractors will be required to provide documentation as per Samuels Group’s procedures.

3. At the connection to the existing Courthouse windows tagged as type 25 as seen on sheet A122B are not being replaced. Existing windows to remain.

4. Window types 26 and 28 are replacing windows in the existing Courthouse. Type 26 are interior and type 28 are exterior to the new Lobby, see elevation 4B/A302. All opening dimensions to be field verified for window sizing.

5. The stair in SPV 1034 is to have handrails on both sides.

6. See sheets A200, A201, and A202 for updates such as but not limited to masonry expansion joint locations and window tags.

7. Plumbing Fixture Schedule: Refer to previously issued construction documents dated 2-17-2017. Only revisions were issued with the VE Coordination package.

8. Evidence locker configurations / 4-Post shelving will be addressed during review of submittals with Owner’s coordination.

9. See attached Schedule as prepared by Samuels Group.

B. SPECIFICATIONS

1. SECTION 00 2419

a. ADD REVISED Section 00 2419 Bid Categories for work as attached to this addendum.

2. SECTIONS 00 4100 & 01 2300

a. CLARIFICATION: There are no alternates for the VE Coordination construction documents.

3. SECTION 06 4100

a. REPLACE Section 06 4100 Architectural Wood Casework with REVISED Section 06 4100 Architectural Wood Casework as attached to this addendum.




00 0492-2

4. SECTION 08 7100

a. REPLACE Section 08 7100 Door Hardware with REVISED Section 08 7100 Door Hardware as attached to this addendum.

5. SECTION 11 4000

a. REPLACE Section 11 4000 Foodservice Equipment with REVISED Section 11 4000 Foodservice Equipment as attached to this addendum.

b. CLARIFICATIONS:

1. Item A111405: Shelving Unity, Starter, Metal, Wire: (3) 24 x 36 units will be located in Cooler 1084 and Freezer 1090; refer to drawing A161K.

2. Item A111407: Shelving, Wire: (10) Stationary shelving units should be provided. See revision to specification.

3. Item A111410: Ice Maker: Electric is 115V/60/1PH not 208-230V/60/1Ph as specified. Model number for remote system is F-1001MRJ. Water filter model # is H9320-52. Remote Compressor model # is URC-5F.

4. Item A111411: Shelving Unit, Starter, Metal, Wire: This item to be 24 x 24.

5. Item A111417: Dishtable, Accessory: Refer to drawing A161K.

6. Item A111418: Waste Can: Item to be Owner Furnished, Owner Installed (OFOI).

7. Item 111422: Pant Leg Condensate Ducts: Provided and installed by Mechanical Subcontractor.

8. Item A111423: Dishwasher, Conveyor Type: electric is 10 kw Heater.

9. Item A111430 is a Hobart Flood Slicer – please submit substitution available for correctional package if available.

10. Item A111432: Work Table, 96” Long: Contractor to PROVIDE Chicago Faucet #201-AGN10AE3SWG319CP. Contractor to PROVIDE Elkay lever drains – size to match drain in sink, 1-1/2” outlet.

11. Item A111434: Shelf, wall-Mount: Specification is correct. Provide (2) 12 x 72 wall mounted shelves. The 12 x 60 equipment was incorrectly tagged, see drawing A161K.

12. Item A111442: Kettle, Electric, Table Top: No, Faucet provided by Plumbing Contractor.

13. Item A111447: Convection Oven, Gas: Item to be Owner Furnished, Contractor Installed (OFCI).

14. Item A111448: See revision to specification as attached to this addendum.

15. Item A111450: Oven, Microwave: Model # is HDC212.

6. SECTION 26 3213

a. CLARIFICATION The maintenance agreement required by paragraphs 3.7.A though 3.7.E will be provided as part of the Owners pre-purchase agreement. No allowance is required from contractor.




00 0492-3

C. DRAWINGS

1. SHEET S201

a. CLARIFICATION: Sheet S201 Bracing Elevations is part of the VE Coordination plans and was included. A copy of S201 is attached for convenience.

2. SHEET S114B (Detail 6C/S114B and 6E/S512)

a. CLARIFICATION: The large HSS section at the curved roof is a HSS16x8x3/8.

3. SHEET E00S

a. CLARIFICATION Fixture type EX is an existing post top acorn fixture to be relocated from the south sidewalk of the existing courthouse. Provide new concrete base per detail and replacement lamp and ballast for fixture.

4. SHEET A101

a. CLARIFICATION: Columns B4 and B7 have been changed to HSS8x8x1/2.

b. CLARIFICATION: Add roof drains where indicated as attached to this addendum.

5. SHEET A131B

a. ADD smooth finish EIFS system to entrance soffit; ADD remaining Lobby ceiling as indicated on plan as attached to this addendum.

6. SHEET A161K

a. CLARIFICATIONS: Refer to specification Section 11 4000 clarifications as listed above.

7. SHEETS A200, A201, A202

a. CLARIFICATIONS: Updates such as but not limited to masonry expansion joint locations and window tags as attached to this addendum.

8. SHEET A604

a. REMOVE window types 21 and 23 as noted on attached drawing.

b. ADD curtain wall type 15 on attached drawing.

9. SHEET E102B

a. ADD keynote E55: “ONE 4 FOOT SECTION CONNECTED TO LIFE SAFETY CIRCUIT.”

10. SHEET E501

a. CHANGE Electrical data for Ice Machine A111410 in the kitchen equipment schedule to 120V/1, 15.2 FLA, 20/1 circuit breaker. Wiring shall remain as scheduled.

11. SHEET E601

a. ADD fixture type L12D to the schedule: 2" x 2" x 4'-0" HORIZONTAL LENGTH LED SUSPENDED DIRECT, EXTRUDED ALUMINUM HOUSING, WITH 1' VERTICAL LIGHT, WITH ONE-PIECE LENS OVER THE 90DEG CORNER, ACRYLIC SATIN LENS MEDIUM DIFFUSE, LED, 400 LUMENS/FT, 4000K, 0-10V LED DRIVER, 277 V, GAMMALUX GB22D2, METALUMEN RM2D, NULITE RP2, SEE DETAIL 4D ON SHEET E500 FOR LIGHT FIXTURE CONFIGURATION.




00 0492-4

b. CLARIFICATION Fixtures types L11, L11A, and L11B are shown and dimensioned in the Lobby and at the top of the stairs on sheet E102B.

12. SHEET E603

a. CHANGE in schedule for panel LRL-K circuit breaker for the ice machine shall be 20/1 in lieu of 15/2. Provide an additional 20/1 circuit breaker in unused space.

D. APPROVED MANUFACTUERS

The following manufacturers are approved for this project, provided the materials and systems meet the requirements of these Contract Documents. This approval does not waive any requirements or conditions of the Contract Documents for any material, system, or manufacturer.

SECTION ITEM SUBSTITUTION

04 7200 Cast Stone MarcStone, LLC – must meet all requirements including but not limited to size, shape, color,

texture, etc.

08 1416 Wood Veneer Doors VT Industries

08 3113 Access Panels Acudoor Fire-Rated Uninsulated Access Panel FB-5060

08 3323 Overhead Doors Rhynor TC200

08 4413 Curtain Wall EFCO Series 5600

08 4413 Door EFCO D300

08 7100 Door Hardware – Electrical Products

Von Duprin (On KIT, Allegion Connect)

08 7100 Door Hardware – Door Monitoring

Schlage Electronics 679-05

08 7100 Door Hardware – Mortise Locks, Exit Devices

Schlage Primus

08 7100 Door Hardware – Latch Device Schlage Mortise Locks

08 7100 Door Hardware – Hanging Device

Ives

08 7100 Mechanical Locks and Latching Allegion, Schlage Multi Point Lockset – only for BP4 - VE

08 7100 Power Transfer Devices Ives Butt and continuous Hinges – only for BP4 - VE

08 7100 Hanging Device Allegion Ives – only for BP4 - VE

08 7100 Electronic Accessories Allegion – only for BP4 - VE

08 7100 Conventional Exit Devices Allegion

11 4000 Item A111456 Model HL400-8STD

Model HL400-4STD

21 1100 Preaction Sprinkler Valve Tyco DV-5

E. ATTACHMENTS

1. 00 2419 Bid Categories (Samuels Group)

2. Schedule (Samuels Group)

3. Section 06 4100

4. Section 08 7100

5. Section 11 4000

6. A101




00 0492-5

7. A131B

8. A161K

9. A200

10. A201

11. A202

12. A604

13. S201

Prepared By: Shive-Hattery, Inc.

END OF DOCUMENT 00 0492

I hereby certify that this engineering document was prepared by me or under my direct personal supervision and that I am a duly licensed Professional Engineer under the laws of the State of Iowa.

Signature Date

Printed or typed name

Michael S. Lewis. AIA

License Number 03968

My License Renewal Date is:

06-30-2019

Pages, Sheets, or Divisions covered by this Seal: This Addendum

wcdegro

Image

Clinton County Justice Center Project # 4163150

Clinton County Justice Center The Samuels Group

Bid Package #4

VE Coordination

BID CATEGORIES

Project # 4163150 7-27-2017 (revised 8-9-2017) 00 2419-1

SECTION 00 2419

BID CATEGORIES FOR WORK PART 1 - GENERAL 1.01 DESCRIPTION

A. Subcontractors are to bid individual Bid Categories as a Prime Contractor to the Owner following

the bidding procedures. A Bid Bond is required.

B. This Section is intended to clarify the scope of work in each Bid Category. Each Bid Category includes all provisions of Division 1 Specifications.

C. When "L&M" is referenced, it shall mean "Labor and Material", when "L" is referenced, it shall mean

"Labor" and when "M" is referenced, it shall mean "Material".

D. The Clarification's listed with some of the Bid Categories are included for the basic understanding of the Scope of Work within the Bid Category, and is not intended to define the limits of the Work for a complete installation. This shall not relieve any Trade Contractor of the requirements within the technical Sections as they are listed.

1.02 BID CATEGORIES

Bid Categories referenced in this Section are for work to be performed at the: Clinton County LEC, 612 North 2nd Street, Clinton, IA 52733.

1.03 SCOPE OF WORK

A. The Bid Categories are constructed to follow as closely as possible the CSI format of the Contract Documents. However, some Bid Categories may contain more than one specification section and/or parts thereof.

B. Local custom and trade-union jurisdictional settlements do not control the scope-of-work included in

each Trade Contract. When a potential jurisdictional dispute or similar interruption of construction activities is first identified or threatened, the affected Contracts shall promptly negotiate a reasonable settlement to avoid or minimize the pending interruption and its delays.

C. Unless noted otherwise, all labor, material and equipment for each specification section is to be

included for each Bid Category.

D. Each Trade Contractor will be responsible for their own cutting and patching, unless indicated differently in the drawings.

E. Project Manager and Foreman are required to attend progress meetings starting 2 weeks prior to

commencement of that Contractors work through completion of contractors work.

F. All Contractors are bound to Division 00 and 01 Requirements.



Bid Package #4

VE Coordination

BID CATEGORIES

Project # 4163150 7-27-2017 (revised 8-9-2017) 00 2419-2

1.04 BID CATEGORIES

1.1 BID CATEGORIES LIST

BID CATEGORY NO. 1 GENERAL REQUIREMENTS

Division 00 – PROCUREMENT AND CONTRACTING REQUIREMENTS

00 01 01 – PROJECT TITLE PAGE

00 01 05 – CERTIFICATE PAGE

00 01 10 – TABLE OF CONTENTS

00 11 16 – INVITATION TO BID

00 21 13 - INSTRUCTIONS TO BIDDERS

00 24 19 - BID CATEGORIES FOR WORK (and WORK SEQUENCE)

00 31 00 – AVAILABLE PROJECT INFROMATION

00 41 00 - BID FORM

00 52 00 – AGREEMENT FORM

00 61 13 – PERFORMANCE AND PAYMENT BOND FORM

00 72 00 - GENERAL CONDITIONS

AIA DOCUMENT A232-2009

INSURANCE REQUIREMENTS

00 80 09 – DEFAULT AND TERMINATION

RIDER A – LABOR OR LABOR/MATERIAL SUPPLIERS ONLY

RIDER A – MATERIAL SUPPLIERS ONLY

RIDER C – TRADE CONTRACTORS AND MATERIAL SUPPLIES

Division 01 – GENERAL REQUIREMENTS

01 11 00 – SUMMARY OF WORK

01 20 00 – PRICE AND PAYMENT PROCEDURES

01 2100 - ALLOWANCES



Bid Package #4

VE Coordination

BID CATEGORIES

Project # 4163150 7-27-2017 (revised 8-9-2017) 00 2419-3

01 30 00 – ADMINISTRATION REQUIREMENTS

01 40 00 – QUALITY REQUIREMENTS (Owner’s Testing & Inspections)

01 41 00 – REQUIRED MOCK UP AND PREINSTALLATION

01 42 19 – REFERENCE STANDARDS

01 45 33 – CODE REQUIRED SPECIAL INSPECTIONS

01 50 00 – TEMPORARY FACILITIES AND CONTROLS

01 60 00 - PRODUCTS REQUIREMENTS

01 61 16 – VOLATILE ORGANIC COMPOUND (VOC) CONTENT RESTRICTIONS.

01 70 00 – EXECUTION AND CLOSEOUT PROCEDURES

01 78 00 – CLOSEOUT

01 79 00 – DEMONSTRATION AND TRAINING

GEOTECHNICAL REPORT / SITE CLASS LETTER

BID CATEGORY NO. 1 – GENERAL CONSTRUCTION PACKAGE – COMBINED BID CATEGORIES AS

INDICATED BELOW (All L&M)

STATUS: REBID

03 30 00 – CAST-IN-PLACE CONCRETE L & M

03 35 11 – CONCRETE FLOOR FINISHES L & M

03 35 20 – GROUND AND POLISHED L & M

05 12 00 – STRUCTURAL STEEL FRAMING M

05 21 00 – STEEL JOISTS FRAMING M

05 31 00 – STEEL DECK M

05 50 00 – METAL FABRICATIONS M

05 51 13 – METAL PAN STAIRS M

05 52 13 – PIPE AND TUBE RAILINGS M

07 13 00 – SHEET WATERPROOFING L & M

07 21 00 – THERMAL INSULATION L & M

07 21 19 – FOAMED-IN-PLACE INSULATION L & M

07 24 00 – EXTERIOR INSULATION AND FINISH SYSTEM L & M

07 27 26 – FLUID APPLIED MEMBRANE AIR BARRIER L & M

07 81 00 – APPLIED FIREPROOFING L & M



Bid Package #4

VE Coordination

BID CATEGORIES

Project # 4163150 7-27-2017 (revised 8-9-2017) 00 2419-4

07 81 23 – INTUMESCENT MASTIC FIREPROOFING L & M

07 27 26 – FLUID APPLIED MEMBRANE AIR BARRIERS L & M

07 90 00 – PRE-COMPRESSED FIRE RATED SEALANT SYTEM L & M

07 92 00 – JOINT SEALANT L & M

07 92 00 – JOINT SEALANT - DETENTION L & M

08 11 13 – STANDARD HOLLOW MENTAL DOORS AND FRAMES L & M

08 14 16 – FLUSH WOOD DOORS L & M

08 31 00 – ACCESS DOORS AND PANELS L & M

08 31 13 – SECURITY ACCESS DOORS AND FRAMES L & M

08 56 59 – SERVICE AND TELLER WINDOW UNITS L & M

08 70 00 – HARDWARE L & M

08 33 13 – COILING COUNTER DOORS L & M

08 33 23 – OVERHEAD COILING DOORS L & M

08 36 13 – SECTIONAL DOORS L & M

08 40 13 – FIRE-RATED GLAZED WALLS L & M

08 44 13 – GLAZED ALUMINUM CURTAIN WALLS L & M

08 80 00 – GLAZING L & M

09 21 16 – GYPSUM BOARD ASSEMBLES/DENS GLASS L & M

09 22 16 – NON-STRUCTURAL METAL FRAMING L & M

05 40 00 – COLD-FORMED METAL FRAMING L & M

09 30 00 – TILING L & M

09 51 00 – ACOUSTICAL CEILINGS L & M

09 57 53 – SECURITY CEILINGS ASSEMBLE L & M

09 84 15 – ACOUSTICAL CEILING BAFFLES L & M

09 65 00 - RESILIENT FLOORING L & M

09 68 13 – TILE CARPETING L & M

09 67 23 – EPOXY RESINOUS FLOOR AND WALL SYSTEM L & M

09 69 00 – ACCESS FLOORING L & M

09 77 33 – GLASS FIBER REINFORCED PLASTIC PANELS L & M

09 90 00 – INTERIOR PAINTING L & M

09 11 13 – EXTERIOR PAINTING L & M

09 96 00 – HIGH-PERFORMANCE COATINGS L & M



Bid Package #4

VE Coordination

BID CATEGORIES

Project # 4163150 7-27-2017 (revised 8-9-2017) 00 2419-5

10 18 00 – TELEVISION AND PROJECTOR MOUNTS L & M

10 21 13 – TOILET COMPARTMENTS L & M

10 26 01 – WALL AND CORNER GUARD L & M

10 44 00 – FIRE PROTECTION SPECIALTY L & M

10 51 00 – LOCKERS L & M

10 51 10 – EVIDENCE LOCKERS L & M

10 51 11 – HIGH SENSITY MOBILE STORAGE L & M

10 55 00 – PACKAGE DROP L & M

10 75 00 – FLAGPOLES L & M

10 80 00 – TOILET ACCESSORIES L & M

11 13 19.23 – STATIONARY LOADING DOCK LIFTS L & M

11 13 50 – PROTECTIVE RAILING SYSTEM L & M

12 24 00 – WINDOW SHADES L & M

12 50 00 – INTERIOR FURNITURE L & M

CLARIFICATIONS:

Include all materials for above Sections unless noted otherwise.

Coordinate all work with other Trade Contractors as required.

All field measurements / verification are included in this bid category. All temporary barricades, enclosures and protection are this Trade Contractors responsibility.

Trade Contractor is responsible for their cleanup.

BID CATEGORY NO. 3 CONCRETE

STATUS: REBID

03 30 00 – CAST-IN-PLACE CONCRETE L & M

03 35 11 – CONCRETE FLOOR FINISHES L & M

03 35 20 – GROUND AND POLISHED L & M

CLARIFICATIONS:

a. Include all labor and materials for above Sections unless noted otherwise.

b. Coordinate all work with other Trade Contractors as required.

a. All temporary barricades, enclosures and protection are this Trade Contractors

responsibility.

b. Trade Contractor is responsible for their cleanup.



Bid Package #4

VE Coordination

BID CATEGORIES

Project # 4163150 7-27-2017 (revised 8-9-2017) 00 2419-6

c. Sealer for concrete floors.

BID CATEGORY NO. 4 MASONRY

STATUS: ACCEPTED – B&B MASONRY

04 20 00 – UNIT MASONRY L & M

04 72 00 – CAST STONE MASONRY L & M

07 20 00 – RIGID INSULATION L & M

07 27 26 – FLUID APPLIED MEMBRANE AIR BARRIER L & M

CLARIFICATIONS:

Include all labor and materials for above Sections unless noted otherwise.

Include all layout for the above Bid Category.


All temporary barricades, enclosures and protection are this Trade Contractors responsibility.

Trade Contractor is responsible for the removal of debris to an approved landfill.


Protect all concrete floors while laying up walls. Many floors are to have exposed concrete finish.

Include all temporary heat and winter protection to protect work.

Include all masonry reinforcement including safety precautions. Safety caps on all rebar are required.

All mixing of mortar and grout will be performed outside the building.

Include all cutting and patching required to complete the work.

Include setting of loose steel lintels, angels, plates and sleeves imbedded in masonry wall, material supplied by others.

Include grouting of Security Hollow Metal Frames if needed.

Include all Firestopping at top of walls.

BID CATEGORY NO. 5 METALS

STATUS: REBID

05 12 00 – STRUCTURAL STEEL FRAMING M

05 21 00 – STEEL JOISTS FRAMING M

05 31 00 – STEEL DECK M

05 50 00 – METAL FABRICATIONS M

05 51 13 – METAL PAN STAIRS M

05 52 13 – PIPE AND TUBE RAILINGS M

CLARIFICATIONS:

Include all labor and for above Sections unless noted otherwise.



Bid Package #4

VE Coordination

BID CATEGORIES

Project # 4163150 7-27-2017 (revised 8-9-2017) 00 2419-7


BID CATEGORY NO. 5A METALS – ERECTION

STATUS: ACCEPTED – CEDAR VALLEY STEEL

05 12 00 – STRUCTURAL STEEL FRAMING L

05 21 00 – STEEL JOISTS FRAMING L

05 31 00 – STEEL DECK L

05 50 00 – METAL FABRICATIONS L

05 51 13 – METAL PAN STAIRS L

05 52 13 – PIPE AND TUBE RAILINGS L

CLARIFICATIONS:



Provide all hoisting equipment to do you scope of work. Any pads/timbers for outrigger is this contractor’s responsibility.


Safety rails are this Trade Contractors responsibility.

Trade Contractor is responsible for the removal of debris to an approved landfill.


Include all cutting and patching required to complete the work.

BID CATEGORY NO. 7B ROOFING

STATUS: ACCEPTED – BLACK HAWK ROOFING

07 22 00 – ROOF AND DECK INSULATION L & M

075323 – TGO-ETHYTLENE-PROPYLENE-DIENE-MONOMER ROOFING FULLY ADHERED L & M

07 54 00 .01 – 60 MIL EPDM ROOF WARRANTY L & M

07 62 00 – SHEET METAL FLASHING AND TRIM L & M

CLARIFICATIONS:







Bid Package #4

VE Coordination

BID CATEGORIES

Project # 4163150 7-27-2017 (revised 8-9-2017) 00 2419-8

BID CATEGORY NO. 7C EXTERIOR INSULATION AND FINISH SYSTEM

STATUS: REBID

07 24 00 – EXTERIOR INSULATION AND FINISH SYSTEM L & M

CLARIFICATIONS:






Include all temporary heat and winter protection to protect work.

BID CATEGORY NO. 7D FIRESTOPPING AND JOINT SEALANT

STATUS: REBID

07 90 00 – PRE-COMPRESSED FIRE RATED SEALANT SYSTEM L & M

07 92 00 – JOINT SEALANT L & M

07 92 10 – JOINT SEALANT - DETENTION L & M

CLARIFICATIONS:





BID CATEGORY NO. 7E APPLIED FIREPROOFING

STATUS: REBID

07 81 00 – APPLIED FIREPROOFING L & M

07 81 23 – INTUMESCENT MASTIC FIREPROOFING L & M

CLARIFICATIONS:






Bid Package #4

VE Coordination

BID CATEGORIES

Project # 4163150 7-27-2017 (revised 8-9-2017) 00 2419-9


BID CATEGORY NO. 7F FLUID-APPLIED MEMBRANE & WATERPROOFING

STATUS: REBID

07 13 00 – SHEET WATERPROOFING L & M

07 27 26 – FLUID-APPLIED MEMBRANE AIR BARRIES L & M

CLARIFICATIONS:





BID CATEGORY NO. 8A DOORS

STATUS: REBID

08 11 13 – STANDARD HOLLOW MENTAL DOORS AND FRAMES M

08 14 16 – FLUSH WOOD DOORS M

08 56 59 – SERVICE AND TELLER WINDOW UNITS M

08 70 00 – HARDWARE M

CLARIFICATIONS:

Include all materials for above Sections unless noted otherwise. .

BID CATEGORY NO. 8B OVERHEAD DOORS/COILING

STATUS: REBID

08 33 13 – COILING COUNTER DOORS L & M

08 33 23 – OVERHEAD COILING DOORS L & M

08 36 13 – SECTIONAL DOORS L & M

CLARIFICATIONS:



Bid Package #4

VE Coordination

BID CATEGORIES

Project # 4163150 7-27-2017 (revised 8-9-2017) 00 2419-10


Include all layout for the above Sections.


Contractor is responsible for all field verification.

Trade Contractor is responsible for their own cleanup.

Include blocking and metal closure strips that are an integral part of the installation. Touch up all framing members as required.

Coordinate all hardware and hardware installation.

BID CATEGORY NO. 8C ALUMINUM STOREFRONTS

STATUS: REBID

08 40 13 – FIRE-RATED GLAZED WALLS L & M

08 44 13 – GLAZED ALUMINUM CURTAIN WALLS L & M

08 80 00 – GLAZING L & M

CLARIFICATIONS:






Include blocking and metal closure strips that are an integral part of the installation. Touch up all framing members as required.

Coordinate all hardware and hardware installation.

BID CATEGORY NO. 9 DRYWALL

STATUS: REBID

07 21 00 – THERMAL INSULATION L & M

07 21 19 – FOAMED-IN-PLACE INSULATION L & M

09 21 16 – GYPSUM BOARD ASSEMBLES/DENS GLASS L & M

09 22 16 – NON-STRUCTURAL METAL FRAMING L & M

05 40 00 – COLD-FORMED METAL FRAMING L & M

CLARIFICATIONS:






Bid Package #4

VE Coordination

BID CATEGORIES

Project # 4163150 7-27-2017 (revised 8-9-2017) 00 2419-11

All temporary barricades, enclosures and protection are this Trade Contractor’s

responsibility.

Trade Contractor is responsible for their own cleanup. Contractor is responsible for

scraping drywall mud off the floor prior to the flooring install.

Include any cutting and patching necessary to complete the specified work.

Include all batt insulation and metal deck closure strips at top of all partitions that terminate to the top or bottom of roof deck.

BID CATEGORY NO. 9A TILING

STATUS: REBID

09 30 00 – TILING L & M

CLARIFICATIONS:






Include filling and patching of minor floor imperfections and depressions where tile

work is scheduled.

BID CATEGORY NO. 9B CEILINGS

STATUS: REBID


09 51 00 – ACOUSTICAL CEILINGS L & M

09 57 53 – SECURITY CEILINGS ASSEMBLE L & M

09 84 15 – ACOUSTICAL CEILING BAFFLES L & M

CLARIFICATIONS:






Include any cutting and patching necessary to complete the specified work, including

ceiling panel cuts to accommodate boxes for electrical devices and lights, etc.

Verify per plans the areas the existing ceiling and grid to remain.



Bid Package #4

VE Coordination

BID CATEGORIES

Project # 4163150 7-27-2017 (revised 8-9-2017) 00 2419-12

BID CATEGORY NO. 9C FLOORING

STATUS: REBID

09 65 00 - RESILIENT FLOORING L & M

09 68 13 – TILE CARPETING L & M

CLARIFICATIONS:






Include filling and patching of minor floor imperfections and depressions where resilient

and carpet are scheduled.

Include all transition strips where adjacent work is next to resilient.

BID CATEGORY NO. 9E EPOXY RESINOUS FLOOR AND WALL SYSTEM

STATUS: REBID

09 67 23 – EPOXY RESINOUS FLOOR AND WALL SYSTEM L & M

CLARIFICATIONS:





BID CATEGORY NO. 9F ACCESS FLOORING

STATUS: REBID

09 69 00 – ACCESS FLOORING L & M

CLARIFICATIONS:





BID CATEGORY NO. 9G PAINTING & WALLCOVERING

STATUS: REBID



Bid Package #4

VE Coordination

BID CATEGORIES

Project # 4163150 7-27-2017 (revised 8-9-2017) 00 2419-13

09 90 00 – INTERIOR PAINTING L & M

09 11 13 – EXTERIOR PAINTING L & M

09 96 00 – HIGH-PERFORMANCE COATINGS L & M

CLARIFICATIONS:



Include touch up paining and repairs to finish painted surfaces where damaged by

other Trades prior to final acceptance.



responsibility.


Include touch up paining and repairs to finish painted surfaces where damaged by

other Trades prior to final acceptance.

BID CATEGORY NO. 10 SPECIALTIES

STATUS: REBID

10 18 00 – TELEVISION AND PROJECTOR MOUNTS M

10 21 13 – TOILET COMPARTMENTS M

10 26 01 – WALL AND CORNER GUARD M

10 44 00 – FIRE PROTECTION SPECIALTY M

10 55 00 – PACKAGE DROP M

10 75 00 – FLAGPOLES M

10 80 00 – TOILET ACCESSORIES M

CLARIFICATIONS:







Bid Package #4

VE Coordination

BID CATEGORIES

Project # 4163150 7-27-2017 (revised 8-9-2017) 00 2419-14

BID CATEGORY NO. 10A LOCKERS

STATUS: REBID

10 51 00 – LOCKERS M

10 51 10 – EVIDENCE LOCKERS M

CLARIFICATIONS:





BID CATEGORY NO. 10B HIGH DENSITY MOBILE STORAGE

STATUS: REBID

10 51 11 – HIGH DENSITY MOBILE STORAGE L & M

CLARIFICATIONS:





BID CATEGORY NO. 11 STATIONARY LOADING DOCK LIFTS

STATUS: REBID

11 13 19.23 – STATIONARY LOADING DOCK LIFTS L & M

CLARIFICATIONS:







Bid Package #4

VE Coordination

BID CATEGORIES

Project # 4163150 7-27-2017 (revised 8-9-2017) 00 2419-15

BID CATEGORY NO. 11B LAUNDRY EQUIPMENT

STATUS: REBID

11 20 00 – LAUNDRY EQUIPMENT L & M

CLARIFICATIONS:






BID CATEGORY NO. 11C FOODSERVICE EQUIPMENT

STATUS: REBID

11 40 00 – FOODSERVICE EQUIPMENT L & M

CLARIFICATIONS:






BID CATEGORY NO. 12 WINDOW SHADES

STATUS: REBID

12 24 00 – WINDOW SHADES L & M

CLARIFICATIONS:








Bid Package #4

VE Coordination

BID CATEGORIES

Project # 4163150 7-27-2017 (revised 8-9-2017) 00 2419-16

BID CATEGORY NO. 14 CONVEYING EQUIPMENT

STATUS: REBID

14 20 10 – PASSENGER ELEVATORS L & M

14 24 00 – HYDRAULIC ELEVATORS L & M

14 28 17 – PASSENGER ELEVATOR CONTROL SYSTEM L & M

14 28 19 – ELEVATOR EQUIPMENT L & M

CLARIFICATIONS:


Furnishing and installation of the adhered masonry veneer.




BID CATEGORY NO. 21 FIRE SUPPRESSION

STATUS: ACCEPTED – COMPANY ONE SPRINKLERS


21 11 00 – FACILITY FIRE-SUPPRESSION WATER-SERVICE PIPING L & M

21 13 00 – FIRE SUPPRESSION SPRINKLER SYSTEMS L & M

CLARIFICATIONS:



Include field measurements.

Coordinate with other Trade Contractor as necessary.

Trade Contractor is responsible for work related firestopping/fire resistive caulking.


Include concrete pads for fire protection equipment.

Fire Protection Contractor will provide all fire protection coordination drawings for

review by other trades. Coordination meetings will be scheduled as needed.

Includes bid categories Division 00, and 01 as applicable

BID CATEGORY NO. 22 PLUMBING

STATUS: ACCEPTED – NORTHWEST MECHANICAL



Bid Package #4

VE Coordination

BID CATEGORIES

Project # 4163150 7-27-2017 (revised 8-9-2017) 00 2419-17

08 31 00 – Access Doors and Panels L & M

22 0500 – Common Work Results for Plumbing L & M

22 0519 – Meters and Gauges for Plumbing Piping L & M

22 0523 – General Duty Valves for Plumbing Piping L & M

22 0529 – Hangers and Supports for Plumbing Piping and Equipment L & M

22 0553 – Identification for Plumbing Piping and Equipment L & M

22 0700 – Plumbing Insulation L & M

22 1116 – Domestic Water Piping L & M

22 1119 – Domestic Water Piping Specialties L & M

22 1123 - Domestic Water Pumps L & M

22 1316 – Sanitary Waste and Vent Piping L & M

22 1319 – Sanitary Waste Piping Specialties L & M

22 1413 – Facility Storm Drainage Piping L & M

22 1423 – Storm Drainage Piping Specialties L & M

22 1429 – Sump Pumps L & M

22 3100 – Domestic Water Softeners L & M

22 3400 – Fuel-Fired Domestic Water Heaters L & M

22 4000 – Plumbing Fixtures L & M

CLARIFICATIONS:




responsibility.



Furnish only any steel embed or sleeve required in any concrete or masonry walls.

Coordinate with other Trade Contractors as required.

Include concrete pads for plumbing equipment.

Include all hook ups to the water, sanitary and storm sewer system, (5) feet outside the

building foundation wall.

Plumbing Contractor will provide all plumbing coordination drawings for review by other

trades. Coordination meetings will be scheduled as needed.



Bid Package #4

VE Coordination

BID CATEGORIES

Project # 4163150 7-27-2017 (revised 8-9-2017) 00 2419-18

All exterior site utilities have been previously bid and awarded.

Any floor to floor penetrations to be completed during off hours.

Includes bid categories Division 00, and 01 as applicable.

BID CATEGORY NO. 23 HEATING, VENTILATING, AND AIR-CONDITIONING (HVAC)

STATUS: ACCEPTED – NORTHWEST MECHANICAL

08 31 00 – Access Doors & Panels L & M

08 91 00 – Louvers L & M

23 05 00 - Common Work Results for HVAC L & M

23 05 13 - Common Motor Requirements for HVAC Equipment L & M

23 05 19 - Meters and Gages for HVAC Piping L & M

23 05 23 - General-Duty Valves for HVAC Piping L & M

23 05 29 - Hangers and Supports for HVAC Piping and Equipment L & M

23 05 48 - Vibration and Seismic Controls for HVAC Piping and Equipment L & M

23 05 53 - Identification for HVAC Piping and Equipment L & M

23 05 93 - Testing, Adjusting, and Balancing for HVAC L & M

23 07 00 - HVAC Insulation L & M

23 08 00 - Mechanical Commissioning Requirements L & M

23 09 00 - Instrumentation and Control for HVAC L & M

23 21 13 - Hydronic Piping L & M

23 21 23 - Hydronic Pumps L & M

23 23 00 - Refrigerant Piping L & M

23 25 00 - HVAC Water Treatment L & M

23 31 13 - Metal Ducts L & M

23 31 16 - Non-Metal Ducts L & M

23 33 00 - Air Duct Accessories L & M

23 34 16 - Centrifugal HVAC Fans L & M

23 34 23 - HVAC Power Ventilators L & M

23 36 00 - Air Terminal Units L & M



Bid Package #4

VE Coordination

BID CATEGORIES

Project # 4163150 7-27-2017 (revised 8-9-2017) 00 2419-19

23 37 13 - Diffusers, Registers, and Grilles L & M

23 37 23 - HVAC Gravity Ventilators L & M

23 38 13 - Commercial-Kitchen Hoods L & M

23 52 16 - Condensing Boilers L & M

23 64 26 - Rotary-Screw Water Chillers L & M

23 73 13 - Modular Central-Station Air-Handling Units L & M

23 73 14 – Modular Central-Station Air-Handling Units L & M

23 74 23 – Packaged, Direct-Fired, Outdoor, Heating – Only Makeup Air Units L & M

23 8 125 - Computer Room Air Conditioners - Ceiling Mounted L & M

23 82 19 Fan Coil Units L & M

23 82 39 – Electric Unit Heaters L & M

23 82 39.10 – Hot Water Unit Heaters L & M

CLARIFICATIONS:



Any minor temporary barricades, enclosures and protection are this Trade Contractor’s

responsibility.



Furnish only any steel embed or sleeve required in any concrete or masonry walls. Coordinate with

Trade Contractors as necessary.

Any HVAC work in corridor space to be weekend work.

Provide concrete pads for mechanical equipment.

HVAC Contractor will provide all HVAC coordination drawings for review by other trades. Coordination meetings will be scheduled as needed.


BID CATEGORY NO. 26 ELECTRICAL

STATUS: REBID


26 05 00 – COMMON WORK RESULTS FOR ELECTRICAL L & M

26 05 01 – MINOR ELECTRICAL DEMOLITION L & M



Bid Package #4

VE Coordination

BID CATEGORIES

Project # 4163150 7-27-2017 (revised 8-9-2017) 00 2419-20

26 05 19 – LOW-VOLTATE ELECTRICAL POWER CONDUCATORS AND CABLE L & M

26 05 26 – GROUNDING AND BONDING FOR ELECTRICAL SYSTEMS L & M

26 05 29 – HANGERS AND SUPPORTS FOR ELECTRICAL SYSTEMS L & M

26 05 34 – CONDUIT L & M

26 05 37 – BOXES L & M

26 05 53 – IDENTIFICATION FOR ELECTRICAL SYSTEMS L & M

26 05 73 – POWER SYSTEM STUDY L & M

26 09 18 – REMOTE CONTROL SWITCHING DEVICES L & M

26 09 23 – LIGHTING CONTROL DEVICES L & M

26 22 00 – LOW-VOLTAGE TRANSFORMERS L & M

26 24 13 – SWITCHBOARDS L & M

26 24 16 – PANELBOARDS L & M

26 27 17 – EQUIPMENT WIRING L & M

26 27 26 – WIRING DEVICES L & M

26 28 13 – FUSES L & M

26 28 18 – ENCLOSED SWITCHES L & M

26 29 13 – ENCLOSED CONTROLLERS L & M

26 29 23 – VARIABLE-FREQUENCY MOTOR CONTROLLERS L & M

26 32 13 – ENGINE GENERATORS L & M

26 36 00 – TRANSFER SWITCHES L & M

26 43 00 – SURGE PROTECTIVE DEVICES L & M

26 51 00 – INTERIOR LIGHTING L & M

26 56 00 – EXTERIOR LIGHTING L & M

CLARIFICATIONS:



All temporary barricades, enclosures and protection are this Trade Contractor’s responsibility.

Furnish only any steel embed or sleeve required in any concrete or masonry walls. Coordinate with Trade Contractors as necessary.

Include all necessary framing/support layouts for coordination with other Trade Contractors.



Include all temporary power, panels and temporary lighting.

Include concrete pads for electrical equipment.

Any work in corridor space shall be scheduled for off hours.

Electrical Contractor will provide all Electrical coordination drawings for review by other trades. Coordination meetings will be scheduled as needed.




Bid Package #4

VE Coordination

BID CATEGORIES

Project # 4163150 7-27-2017 (revised 8-9-2017) 00 2419-21

BID CATEGORY NO. 27 COMMUNICATIONS

STATUS: REBID

27 05 28 – PATHWAYS FOR COMMUNICATIONS SYSTEMS L & M

27 05 44 – SLEEVES & SLEEVE SEALS FOR COMMUNICATIONS PATHWAYS & CABLING

L & M

27 11 00 – COMMUNICATIONS EQUIPMENT ROOM FITTINGS L & M

27 13 00 – COMMUNICATIONS BACKBONE CABLING L & M

27 15 00 – COMMUNICATIONS HORIZONTAL CABLING L & M

27 51 17 – PUBLIC ADDRSS SYSTEMS L & M

CLARIFICATIONS:




Furnish only any steel embed or sleeve required in any concrete or masonry walls. Coordinate with Trade Contractors as necessary.




Include all temporary power panels and temporary lighting.





Electrical Contractor will provide all Electrical coordination drawings for review by other trades.

Coordination meetings will be scheduled as needed.

l. Includes bid categories Division 00, and 01 as applicable



Bid Package #4

VE Coordination

BID CATEGORIES

Project # 4163150 7-27-2017 (revised 8-9-2017) 00 2419-22

BID CATEGORY NO. 28 ELECTRONIC SAFETY & SECURITY

STATUS: REBID

28 05 13 – CONDUCTORS & CABLES FOR ELECTRONIC SAFETY & SECURITY L & M

28 05 28 – PATHEAYS FOR ELECTRONIC SAFETY & SECURITY L & M

28 31 11 – DIGITAL, ADDRESSABLE FIRE ALARM SYSTEM L & M

CLARIFICATIONS:












BID CATEGORY 28A COMBINED ELECTRICAL, COMMUNICATIONS, AND ELECTRONIC SAFETY AND SECURITY. INCLUDES SPECIFICATIONS AND CLARIFICATION UNDER EACH BID CATEGORY.



Bid Package #4

VE Coordination

BID CATEGORIES

Project # 4163150 7-27-2017 (revised 8-9-2017) 00 2419-23

BID CATEGORY NO. 32 EARTHWORK

STATUS: ACCEPTED – LARRY DETTERMAN INC.

32 11 23 – DENSE GRADED BASE L & M

32 12 16 – ASPHALT PAVING L & M

32 13 13 – PORTLAND CEMENT CONCRETE PAVING L & M

32 17 23 – PAVEMENT MARKINGS L & M

CLARIFICATIONS:

a. Include all labor and materials for above Sections unless noted otherwise.

b. Coordinate all work with other Trade Contractors as required.

c. All temporary barricades, enclosures and protection are this Trade Contractors

responsibility.

d. Trade Contractor is responsible for their own cleanup.

e. Include all cutting and patching required to complete the work.

f. Include protection of underground utilities; locate public and private underground

utilities prior to excavation.

g. Include necessary grading to allow for placement of plantings.

h. Include earthwork related to slab on grade and exterior improvements

i. Include earthwork and base drives, parking lots, sidewalks, curbs and gutter and finish

grading to =/- 1/10 foot.

j. Include removal of all excess dirt within the shown construction limits from the site at

the completion of the projects.

k. Install and maintain silt fence. Visit site to verify quantity and extent of work. After

completion of project, remove and dispose of silt fence and stakes. Final grade as

required.

l. Include all safety material necessary to protect personnel in and from open trenches or

excavations. Excavations shall be closed as soon as possible.

m. Include subgrade preparation and test rolling.

n. Include all labor and equipment necessary to remove existing site paving, concrete

curb and gutter, sidewalks, trees and miscellaneous landscaping as shown on Sheet

C100. Contractor is responsible for removal of all demo materials off site.

END OF SECTION 00 24 19

Activity ID Activity Name Start Finish

6982 Clinton6982 Clinton Co LEC 07-Mar-17 08:00 AM A

15-Apr-19 04:00 PM

6982.2 Firs6982.2 First Floor Jail 07-Mar-17 08 31-Jan-19 04:00 P

A1010 Excavate Footings & Foundations 07-Mar-17 08 27-Mar-17 04:00 PA10 Mobilization 07-Mar-17 08A1020 Footing & Pads 28-Mar-17 08 24-Apr-17 04:00 PA1030 Foundation Walls 13-Apr-17 08 13-Apr-17 04:00 PA1031 Backfill Foundation Walls 28-Jul-17 08 03-Aug-17 04:00 PA20 Out to Bid 28-Jul-17 08A1050 Underground Plumbing 04-Aug-17 0 07-Sep-17 04:00 PA1070 Addendum 1 08-Aug-17 0A30 Bids Due 15-Aug-17 0A40 Recomendation Presentation 17-Aug-17 0A50 County Board Approval 21-Aug-17 0A1060 Underground Electric 22-Sep-17 0 26-Oct-17 04:00 PMA1100 Slab on Grade 27-Oct-17 08 02-Nov-17 04:00 PA1040 Steel Erection/Column and Beams 03-Nov-17 08 30-Nov-17 04:00 PA1120 Security Cells Installation/Pod Control/Stairs 15-Nov-17 08 05-Dec-17 04:00 PA1080 Exterior Masonry 01-Dec-17 08 11-Jan-18 04:00 PA1140 Detention Finish Welding 06-Dec-17 08 30-Jan-18 04:00 PA1041 Install Bar Joist 06-Dec-17 08 26-Dec-17 04:00 PA1102 Hollow Metal Frames 06-Dec-17 08 12-Dec-17 04:00 PA1042 Metal Decking 15-Dec-17 08 28-Dec-17 04:00 PA1071 Exterior Metal Studs 27-Dec-17 08 16-Jan-18 04:00 PA1090 Roofing 29-Dec-17 08 11-Jan-18 04:00 PA1101 Detention Frames & Embeds 29-Dec-17 08 25-Jan-18 04:00 PA1160 Interior Metal Studs 17-Jan-18 08 13-Mar-18 04:00 PA1081 Exterior Sheeting 17-Jan-18 08 06-Feb-18 04:00 PA1082 Brick 24-Jan-18 08 03-Apr-18 04:00 PA1130 Interior Masonry 26-Jan-18 08 19-Apr-18 04:00 PA1162 Plumbing Roughins 14-Feb-18 08 31-Jul-18 04:00 PMA1163 HVAC Roughins 14-Feb-18 08 31-Jul-18 04:00 PMA1164 Sprinkler Roughins 14-Feb-18 08 10-Jul-18 04:00 PMA1161 Electrical Roughin's 21-Feb-18 08 07-Aug-18 04:00 PA1150 Install Windows and Storefront 04-Apr-18 08 01-May-18 04:00 PA1170 Insulation 25-Jul-18 08 07-Aug-18 04:00 PA1180 Drywall 01-Aug-18 0 25-Sep-18 04:00 PA1200 Tape and Finish 22-Aug-18 0 25-Sep-18 04:00 PA1190 Install Walk-in Freezer & Cooler 05-Sep-18 0 11-Sep-18 04:00 PA1201 Painting 12-Sep-18 0 16-Oct-18 04:00 PMA1280 Install Sprinkler heads 20-Sep-18 0 17-Oct-18 04:00 PMA1330 Set up Video Visitation 24-Sep-18 0 05-Oct-18 04:00 PMA1260 Install Detention Furnishings 26-Sep-18 0 23-Oct-18 04:00 PMA1270 Ceilings 26-Sep-18 0 09-Oct-18 04:00 PMA1360 Install Camera's 26-Sep-18 0 02-Oct-18 04:00 PMA1220 Install Lockers 01-Oct-18 08 05-Oct-18 04:00 PMA1230 Detention Ceilings 01-Oct-18 08 23-Nov-18 04:00 PA1250 Laundry Equipment 01-Oct-18 08 05-Oct-18 04:00 PMA1210 Set up Master Control 03-Oct-18 08 30-Oct-18 04:00 PMA1290 Flooring 08-Oct-18 08 16-Nov-18 04:00 PA1690 Security Electronics 17-Oct-18 08 11-Dec-18 04:00 PA1300 Doors & Hardware 22-Oct-18 08 23-Nov-18 04:00 PA1320 Install 911 Furniture 29-Oct-18 08 02-Nov-18 04:00 PA1310 Bathroom Partitions 05-Nov-18 08 09-Nov-18 04:00 PA1340 Test & Balance 26-Nov-18 08 21-Dec-18 04:00 PA1350 Test all Detention Equipment 12-Dec-18 08 25-Dec-18 04:00 PA1370 Final Cleaning 26-Dec-18 08 01-Jan-19 04:00 PA1380 Punch Out 02-Jan-19 08 03-Jan-19 04:00 PA1390 Complete Punch Items 04-Jan-19 08 17-Jan-19 04:00 P

6982.2.1 Sec6982.2.1 Second Floor 29-Dec-17 08 31-Jan-19 04:00 PA1400 Structural Steel 29-Dec-17 08 11-Jan-18 04:00 PA1410 Roof Bar Joists 12-Jan-18 08 25-Jan-18 04:00 PA1420 Roof Decking 26-Jan-18 08 08-Feb-18 04:00 PA1430 Pour Topping 09-Feb-18 08 15-Feb-18 04:00 PA1440 Roofing 16-Feb-18 08 01-Mar-18 04:00 PA1441 Metal Studs 02-Mar-18 08 29-Mar-18 04:00 PA1442 Install Hollow Metal Frames 30-Mar-18 08 05-Apr-18 04:00 PA1480 Sprinkler Roughins 13-Jun-18 08 07-Aug-18 04:00 PA1460 Plumbing Roughins 20-Jun-18 08 28-Aug-18 04:00 PA1470 HVAC Roughins 20-Jun-18 08 28-Aug-18 04:00 PA1450 Electrical Roughins 27-Jun-18 08 04-Sep-18 04:00 PA1490 Insulation 05-Sep-18 0 11-Sep-18 04:00 PA1500 Drywall 12-Sep-18 0 09-Oct-18 04:00 PMA1510 Tape and Finish 10-Oct-18 08 13-Nov-18 04:00 PA1520 Painting 31-Oct-18 08 04-Dec-18 04:00 PA1540 Ceilings 14-Nov-18 08 27-Nov-18 04:00 PA1570 Install Camera's 21-Nov-18 08 04-Dec-18 04:00 PA1541 Flooring 21-Nov-18 08 04-Dec-18 04:00 PA1530 Mechanical Finishes 28-Nov-18 08 25-Dec-18 04:00 PA1560 Install Casework 28-Nov-18 08 18-Dec-18 04:00 PA1550 Install Doors and Hardware 05-Dec-18 08 18-Dec-18 04:00 PA1580 Test and Balance 26-Dec-18 08 08-Jan-19 04:00 PA1590 Final Clean 09-Jan-19 08 15-Jan-19 04:00 PA1600 Punch Out 16-Jan-19 08 17-Jan-19 04:00 PA1610 Complete Punch list 18-Jan-19 08 31-Jan-19 04:00 PA1620 Complete with Building 31-Jan-19 04:00 P

6982.1 Exte6982.1 Exterior Sitework 01-Sep-17 0 15-Apr-19 04:00 P

A1000 Site Utilities 01-Sep-17 0 21-Sep-17 04:00 PA1001 Demo Existing Jail 01-Mar-19 08 21-Mar-19 04:00 PA1630 Site Grading 22-Mar-19 08 26-Mar-19 04:00 PA1640 Install Stone Base 27-Mar-19 08 28-Mar-19 04:00 PA1650 Exterior Concrete/Sidewalks 29-Mar-19 08 04-Apr-19 04:00 PA1660 Asphalt 05-Apr-19 08 08-Apr-19 04:00 P

8 04 11 18 25 02 09 16 23 30 06 13 20 27 03 10 17 24 01 08 15 22 29 05 12 19 26 03 10 17 24 31 07 14 21 28 04 11 18 25 04 11 18 25 01 08 15 22 29 06 13 20 27 03 10 17 24 01 08 15 22 29 05 12 19 26 02 09 16 23 30 07 14 21 28 04 11 18 25 02 09 16 23 30 06 13 20 27 03 10 17 24 03 10 17 24 31 07 14 21 28 05 12 19 26 02 09 16 23June 2017 July 2017 August 2017 September 2017 October 2017 November 2017 December 2017 January 2018 February 2018 March 2018 April 2018 May 2018 June 2018 July 2018 August 2018 September 2018 October 2018 November 2018 December 2018 January 2019 February 2019 March 2019 April 2019 May 2019 June 2019

15-Apr-19 04:00 PM, 6982 Clinton Co LEC

31-Jan-19 04:00 PM, 6982.2 First Floor Jail

Backfill Foundation WallsOut to Bid

Underground PlumbingAddendum 1

Bids DueRecomendation Presentation

County Board ApprovalUnderground Electric

Slab on GradeSteel Erection/Column and Beams

Security Cells Installation/Pod Control/StairsExterior Masonry

Detention Finish WeldingInstall Bar Joist

Hollow Metal FramesMetal Decking

Exterior Metal StudsRoofing

Detention Frames & EmbedsInterior Metal Studs

Exterior SheetingBrick

Interior MasonryPlumbing RoughinsHVAC Roughins

Sprinkler RoughinsElectrical Roughin's

Install Windows and StorefrontInsulation

DrywallTape and Finish

Install Walk-in Freezer & CoolerPaintingInstall Sprinkler heads

Set up Video VisitationInstall Detention Furnishings

CeilingsInstall Camera's

Install LockersDetention Ceilings

Laundry EquipmentSet up Master Control

FlooringSecurity Electronics

Doors & HardwareInstall 911 Furniture

Bathroom PartitionsTest & Balance

Test all Detention EquipmentFinal CleaningPunch Out

Complete Punch Items31-Jan-19 04:00 PM, 6982.2.1 Second Floor

Structural SteelRoof Bar Joists

Roof DeckingPour Topping

RoofingMetal Studs

Install Hollow Metal FramesSprinkler Roughins

Plumbing RoughinsHVAC Roughins

Electrical RoughinsInsulation

DrywallTape and Finish

PaintingCeilings

Install Camera'sFlooring

Mechanical FinishesInstall CaseworkInstall Doors and Hardware

Test and BalanceFinal CleanPunch Out

Complete Punch listComplete with Building

15-Apr-19 04:00 PM, 6982.1 Exterior Sitework

Site UtilitiesDemo Existing Jail

Site GradingInstall Stone Base

Exterior Concrete/SidewalksAsphalt

Clinton Co LEC Classic Schedule Layout Rods layout 3 02-Aug-17 03:25 PM

Actual WorkRemaining Work

Critical Remaining WorkMilestone

Summary Page 1 of 2 TASK filter: All Activities© Oracle Corporation

Activity ID Activity Name Start Finish

A1670 Landscaping 09-Apr-19 08 15-Apr-19 04:00 PA1680 Sitework Complete 15-Apr-19 04:00 P

8 04 11 18 25 02 09 16 23 30 06 13 20 27 03 10 17 24 01 08 15 22 29 05 12 19 26 03 10 17 24 31 07 14 21 28 04 11 18 25 04 11 18 25 01 08 15 22 29 06 13 20 27 03 10 17 24 01 08 15 22 29 05 12 19 26 02 09 16 23 30 07 14 21 28 04 11 18 25 02 09 16 23 30 06 13 20 27 03 10 17 24 03 10 17 24 31 07 14 21 28 05 12 19 26 02 09 16 23June 2017 July 2017 August 2017 September 2017 October 2017 November 2017 December 2017 January 2018 February 2018 March 2018 April 2018 May 2018 June 2018 July 2018 August 2018 September 2018 October 2018 November 2018 December 2018 January 2019 February 2019 March 2019 April 2019 May 2019 June 2019

LandscapingSitework Complete

Clinton Co LEC Classic Schedule Layout Rods layout 3 02-Aug-17 03:25 PM

Actual WorkRemaining Work

Critical Remaining WorkMilestone

Summary Page 2 of 2 TASK filter: All Activities© Oracle Corporation

Clinton County Justice Center Bid Package #4 VE Coordination

ARCHITECTURAL WOOD

CASEWORK Project # 4163150 07-14-2017

(Addenda #2 issue date 08-08-2017)

06 4100-1

SECTION 06 4100 - REVISED

ARCHITECTURAL WOOD CASEWORK

PART 1 GENERAL

1.1 SECTION INCLUDES

A. Specially fabricated cabinet units.

B. Cabinet hardware.

C. Factory finishing.

D. Custom wood ceiling panels, lobby areas.

1.2 RELATED REQUIREMENTS

A. Section 06 1000 - Rough Carpentry: Support framing, grounds, and concealed blocking.

B. Section 12 3600 - Countertops.

C. Section 08 8000 - Glazing: Glass for casework.

1.3 REFERENCE STANDARDS

A. AWI/AWMAC/WI (AWS) - Architectural Woodwork Standards; 2014.

B. BHMA A156.9 - American National Standard for Cabinet Hardware; 2010.

C. NEMA LD 3 - High-Pressure Decorative Laminates; 2005.

D. AWI/AWMAC/WI (AWS) - Architectural Woodwork Standards; 2014.

E. BHMA A156.9 - American National Standard for Cabinet Hardware; 2010.

F. NEMA LD 3 - High-Pressure Decorative Laminates; 2005.

1.4 SUBMITTALS

A. See Section 01 3000 - Administrative Requirements, for submittal procedures.

B. Shop Drawings: Indicate materials, component profiles, fastening methods, jointing details, and accessories.

1. Minimum Scale of Detail Drawings: 1-1/2 inch to 1 foot (1:8).

2. Provide the information required by AWI/AWMAC/WI (AWS).

3. Include certification program label.

C. Product Data: Provide data for hardware accessories.

D. Samples: Submit actual samples of architectural cabinet construction, minimum 12 inches (300 mm) square, illustrating proposed cabinet, countertop, and shelf unit substrate and finish.

E. Samples: Submit actual sample items of proposed pulls, hinges, shelf standards, and locksets, demonstrating hardware design, quality, and finish.

http://www.awinet.org/

http://global.ihs.com/doc_detail.cfm?rid=BSD&document_name=ANSI%20A156.9

http://global.ihs.com/doc_detail.cfm?rid=BSD&document_name=NEMA%20LD%203







Bid Package #4 VE Coordination

06 4100-2 07-14-2017 (Addenda #2 issue date 08-08-

2017)

1.5 QUALITY ASSURANCE

A. Fabricator Qualifications: Company specializing in fabricating the products specified in this section with minimum five years of documented experience.

1. Shop that employs skilled workers who custom fabricate products similar to those required for this project and whose products have records of successful in-service performance. Shop can demonstrate their products are fabricated in accordance with the AWI's Quality Certification Program standards and requirements.

1.6 DELIVERY, STORAGE, AND HANDLING

A. Protect units from moisture damage.

1.7 FIELD CONDITIONS

A. During and after installation of custom cabinets, maintain temperature and humidity conditions in building spaces at same levels planned for occupancy.

PART 2 PRODUCTS

2.1 CABINETS

A. Quality Grade: Unless otherwise indicated provide products of quality specified by AWI/AWMAC/WI (AWS) for Custom Grade.

B. Plastic Laminate Faced Cabinets: Custom grade.

2.2 WOOD-BASED COMPONENTS

A. Wood fabricated from old growth timber is not permitted.

2.3 LAMINATE MATERIALS

A. Manufacturers:

1. Formica Corporation: www.formica.com.

2. Panolam Industries International, Inc\Nevamar: www.nevamar.com.

3. Wilsonart: www.wilsonart.com.

4. Substitutions: See Section 01 6000 - Product Requirements.

B. High Pressure Decorative Laminate (HPDL): NEMA LD 3, types as recommended for specific applications.

C. Provide specific types as scheduled.

1. Horizontal Surfaces: HGS, 0.048 inch (1.22 mm) nominal thickness, through color, colors as scheduled, finish as scheduled.

2. Vertical Surfaces: VGS, 0.028 inch (0.71 mm) nominal thickness, through color, colors as scheduled, finish as scheduled.

3. Cabinet Liner: CLS, 0.020 inch (0.51 mm) nominal thickness, through color, colors as scheduled, finish as scheduled.

4. Laminate Backer: BKL, 0.020 inch (0.51 mm) nominal thickness, undecorated; for application to concealed backside of panels faced with high pressure decorative laminate.






07-14-2017 (Addenda #2 issue date 08-08-

2017)

06 4100-3

2.4 ACCESSORIES

A. Adhesive: Type recommended by fabricator to suit application.

B. Fasteners: Size and type to suit application.

C. Bolts, Nuts, Washers, Lags, Pins, and Screws: Of size and type to suit application; galvanized or chrome-plated finish in concealed locations and stainless steel or chrome-plated finish in exposed locations.

D. Concealed Joint Fasteners: Threaded steel.

E. Metal Reveal: 2-inch anodized aluminum reveal at Lobby Reception desk. Basis-of-Design Product: Stylmark Flat Bar 110051: 2” x ½”.”

2.5 WOOD CEILING PANLELS – WOOD-BASED COMPONENT

A. Quality Grade – Custom

B. Wood Veneer Faced Cabinet

1. Exposed Surfaces: HPVA Grade A, species as indicated by finishes, plain sliced, slip-matched.

2. Stain, color, and texture as indicated.

3. Direction of grain as indicated.

2.6 HARDWARE

A. Hardware: BHMA A156.9, types as recommended by fabricator for quality grade specified.

B. Adjustable Shelf Supports: Standard side-mounted system using recessed metal shelf standards and coordinated self rests, satin chrome finish, for nominal 1 inch (25 mm) spacing adjustments.

1. Product: 255 manufactured by Knape and Vogt.

C. Adjustable Shelf Supports: Standard back-mounted system using surface mounted metal shelf standards and coordinated cantilevered shelf brackets, satin chrome finish, for nominal 1 inch (25 mm) spacing adjustments.

1. Product: 85/185 Series manufactured by Knape and Vogt.

D. Drawer and Door Pulls: Bar Pull.

1. Product: Cornerstone Collection, brushed satin nickel manufactured by Studio 917 Available through Holdahl Co,

E. Cabinet Locks: Keyed cylinder, two keys per lock, master keyed, steel with chrome finish.

1. Product: Cabinet Lock manufactured by Medeco.

F. Catches: Magnetic.

G. Drawer Slides:

1. Type: Extension types as scheduled.

2. Static Load Capacity: Commercial grade.






2017)

3. Mounting: Side mounted.

4. Stops: Integral type.

5. Manufacturers

a. Accuride International, Inc: www.accuride.com. b. Grass America Inc: www.grassusa.com. c. Hettich America, LP: www.hettichamerica.com. d. Knape & Vogt Manufacturing Company: www.knapeandvogt.com.

H. Hinges: European style concealed self-closing type, steel with satin finish.

2.7 FABRICATION

A. Assembly: Shop assemble cabinets for delivery to site in units easily handled and to permit passage through building openings.

B. Fitting: When necessary to cut and fit on site, provide materials with ample allowance for cutting. Provide matching trim for scribing and site cutting.

C. Plastic Laminate: Apply plastic laminate finish in full uninterrupted sheets consistent with manufactured sizes. Fit corners and joints hairline; secure with concealed fasteners. Slightly bevel arises. Locate counter butt joints minimum 2 feet (600 mm) from sink cut-outs.

D. Matching Wood Grain: Comply with requirements of quality standard for specified Grade and as follows:

1. Provide center matched panels at each elevation.

E. Mechanically fasten back splash to countertops as recommended by laminate manufacturer at 16 inches (400 mm) on center.

F. Provide cutouts for plumbing fixtures. Verify locations of cutouts from on-site dimensions. Prime paint cut edges.

2.8 SHOP FINISHING

A. Sand work smooth and set exposed nails and screws.

PART 3 EXECUTION

3.1 EXAMINATION

A. Verify adequacy of backing and support framing.

B. Verify location and sizes of utility rough-in associated with work of this section.

3.2 INSTALLATION

A. Install work in accordance with AWI/AWMAC/WI (AWS) requirements for grade indicated.

B. Set and secure custom cabinets in place, assuring that they are rigid, plumb, and level.

C. Use fixture attachments in concealed locations for wall mounted components.

D. Use concealed joint fasteners to align and secure adjoining cabinet units.

E. Carefully scribe casework abutting other components, with maximum gaps of 1/32 inch (0.79 mm). Do not use additional overlay trim for this purpose.






2017)

06 4100-5

F. Countersink anchorage devices at exposed locations. Conceal with solid wood plugs of species to match surrounding wood; finish flush with surrounding surfaces.

G. Adhere cork tack surface to substrate with adhesive design to bond to cork and substrate material.

3.3 ADJUSTING

A. Adjust installed work.

B. Adjust moving or operating parts to function smoothly and correctly.

3.4 CLEANING

A. Clean casework, counters, shelves, hardware, fittings, and fixtures.

END OF SECTION





2017)


DOOR HARDWARE

Project # 4163150 07-14-2017 (Addenda #2 issue date 08-08-

2017)

08 7100-1

SECTION 08 7100 - REVISED

DOOR HARDWARE

PART 1 GENERAL

1.1 RELATED DOCUMENTS

A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections, apply to this Section.

1.2 SUMMARY

A. This Section includes commercial door hardware for the following:

1. Swinging doors.

2. Other doors to the extent indicated.

B. Door hardware includes, but is not necessarily limited to, the following:

1. Mechanical door hardware.

2. Electromechanical door hardware.

3. Automatic operators.

4. Cylinders specified for doors in other sections.

C. Codes and References: Comply with the version year adopted by the Authority Having Jurisdiction.

1. ANSI A117.1 - Accessible and Usable Buildings and Facilities.

2. ICC/IBC - International Building Code.

3. NFPA 70 - National Electrical Code.

4. NFPA 80 - Fire Doors and Windows.

5. NFPA 101 - Life Safety Code.

6. NFPA 105 - Installation of Smoke Door Assemblies.

7. UL/ULC and CSA C22.2 - Standards for Automatic Door Operators Used on Fire and Smoke Barrier Doors and Systems of Doors.

8. State Building Codes, Local Amendments.

D. Standards: All hardware specified herein shall comply with the following industry standards:

1. ANSI/BHMA Certified Product Standards - A156 Series

2. UL10C - Positive Pressure Fire Tests of Door Assemblies

1.3 SUBMITTALS

A. Product Data: Manufacturer's product data sheets including installation details, material descriptions, dimensions of individual components and profiles, operational descriptions and finishes.


DOOR HARDWARE Bid Package #4 VE Coordination


2017)

B. Door Hardware Schedule: Prepared by or under the supervision of supplier, detailing fabrication and assembly of door hardware, as well as procedures and diagrams. Coordinate the final Door Hardware Schedule with doors, frames, and related work to ensure proper size, thickness, hand, function, and finish of door hardware.

1. Format: Comply with scheduling sequence and vertical format in DHI's "Sequence and Format for the Hardware Schedule."

2. Organization: Organize the Door Hardware Schedule into door hardware sets indicating complete designations of every item required for each door or opening. Organize door hardware sets in same order as in the Door Hardware Sets at the end of Part 3. Submittals that do not follow the same format and order as the Door Hardware Sets will be rejected and subject to resubmission.

3. Content: Include the following information:

a. Type, style, function, size, label, hand, and finish of each door hardware item.

b. Manufacturer of each item.

c. Fastenings and other pertinent information.

d. Location of door hardware set, cross-referenced to Drawings, both on floor plans and in door and frame schedule.

e. Explanation of abbreviations, symbols, and codes contained in schedule.

f. Mounting locations for door hardware.

g. Door and frame sizes and materials.

h. Warranty information for each product.

4. Submittal Sequence: Submit the final Door Hardware Schedule at earliest possible date, particularly where approval of the Door Hardware Schedule must precede fabrication of other work that is critical in the Project construction schedule. Include Product Data, Samples, Shop Drawings of other work affected by door hardware, and other information essential to the coordinated review of the Door Hardware Schedule.

C. Shop Drawings: Details of electrified access control hardware indicating the following:

1. Wiring Diagrams: Upon receipt of approved schedules, submit detailed system wiring diagrams for power, signaling, monitoring, communication, and control of the access control system electrified hardware. Differentiate between manufacturer-installed and field-installed wiring. Include the following:

a. Elevation diagram of each unique access controlled opening showing location and interconnection of major system components with respect to their placement in the respective door openings.

b. Complete (risers, point-to-point) access control system block wiring diagrams.

c. Wiring instructions for each electronic component scheduled herein.

2. Electrical Coordination: Coordinate with related sections the voltages and wiring details required at electrically controlled and operated hardware openings.



DOOR HARDWARE


2017)

08 7100-3

D. Keying Schedule: After a keying meeting with the owner has taken place prepare a separate keying schedule detailing final instructions. Submit the keying schedule in electronic format. Include keying system explanation, door numbers, key set symbols, hardware set numbers and special instructions. Owner must approve submitted keying schedule prior to the ordering of permanent cylinders/cores.

E. Informational Submittals:

1. Product Test Reports: Indicating compliance with cycle testing requirements, based on evaluation of comprehensive tests performed by manufacturer and witnessed by a qualified independent testing agency.

F. Operating and Maintenance Manuals: Provide manufacturers operating and maintenance manuals for each item comprising the complete door hardware installation in quantity as required in Division 01, Closeout Submittals.


A. Manufacturers Qualifications: Engage qualified manufacturers with a minimum 5 years of documented experience in producing hardware and equipment similar to that indicated for this Project and that have a proven record of successful in-service performance.

B. Installer Qualifications: A minimum 3 years documented experience installing both standard and electrified door hardware similar in material, design, and extent to that indicated for this Project and whose work has resulted in construction with a record of successful in-service performance.

C. Door Hardware Supplier Qualifications: Experienced commercial door hardware distributors with a minimum 5 years documented experience supplying both mechanical and electromechanical hardware installations comparable in material, design, and extent to that indicated for this Project. Supplier recognized as a factory direct distributor by the manufacturers of the primary materials with a warehousing facility in Project's vicinity. Supplier to have on staff a certified Architectural Hardware Consultant (AHC) available during the course of the Work to consult with Contractor, Architect, and Owner concerning both standard and electromechanical door hardware and keying.

D. Source Limitations: Obtain each type and variety of door hardware specified in this section from a single source unless otherwise indicated.

1. Electrified modifications or enhancements made to a source manufacturer's product line by a secondary or third party source will not be accepted.

2. Provide electromechanical door hardware from the same manufacturer as mechanical door hardware, unless otherwise indicated.

E. Each unit to bear third party permanent label demonstrating compliance with the referenced standards.

F. Keying Conference: Conduct conference to comply with requirements in Division 01 Section "Project Meetings." Keying conference to incorporate the following criteria into the final keying schedule document:

1. Function of building, purpose of each area and degree of security required.

2. Plans for existing and future key system expansion.

3. Requirements for key control storage and software.




2017)

4. Installation of permanent keys, cylinder cores and software.

5. Address and requirements for delivery of keys.

G. Pre-Submittal Conference: Conduct coordination conference in compliance with requirements in Division 01 Section "Project Meetings" with attendance by representatives of Supplier(s), Installer(s), and Contractor(s) to review proper methods and the procedures for receiving, handling, and installing door hardware.

1. Prior to installation of door hardware, conduct a project specific training meeting to instruct the installing contractors' personnel on the proper installation and adjustment of their respective products. Product training to be attended by installers of door hardware (including electromechanical hardware) for aluminum, hollow metal and wood doors. Training will include the use of installation manuals, hardware schedules, templates and physical product samples as required.

2. Inspect and discuss electrical roughing-in, power supply connections, and other preparatory work performed by other trades.

3. Review sequence of operation narratives for each unique access controlled opening.

4. Review and finalize construction schedule and verify availability of materials.

5. Review the required inspecting, testing, commissioning, and demonstration procedures

H. At completion of installation, provide written documentation that components were applied to manufacturer's instructions and recommendations and according to approved schedule.

1.5 DELIVERY, STORAGE, AND HANDLING

A. Inventory door hardware on receipt and provide secure lock-up and shelving for door hardware delivered to Project site. Do not store electronic access control hardware, software or accessories at Project site without prior authorization.

B. Tag each item or package separately with identification related to the final Door Hardware Schedule, and include basic installation instructions with each item or package.

C. Deliver, as applicable, permanent keys, cylinders, cores, access control credentials, software and related accessories directly to Owner via registered mail or overnight package service. Instructions for delivery to the Owner shall be established at the "Keying Conference".

1.6 COORDINATION

A. Templates: Obtain and distribute to the parties involved templates for doors, frames, and other work specified to be factory prepared for installing standard and electrified hardware. Check Shop Drawings of other work to confirm that adequate provisions are made for locating and installing hardware to comply with indicated requirements.

B. Door Hardware and Electrical Connections: Coordinate the layout and installation of scheduled electrified door hardware and related access control equipment with required connections to source power junction boxes, low voltage power supplies, detection and monitoring hardware, and fire and detection alarm systems.

C. Door and Frame Preparation: Doors and corresponding frames are to be prepared, reinforced and pre-wired (if applicable) to receive the installation of the specified electrified, monitoring, signaling and access control system hardware without additional in-field modifications.



DOOR HARDWARE


2017)

08 7100-5

1.7 WARRANTY

A. General Warranty: Reference Division 01, General Requirements. Special warranties specified in this Article shall not deprive Owner of other rights Owner may have under other provisions of the Contract Documents and shall be in addition to, and run concurrent with, other warranties made by Contractor under requirements of the Contract Documents.

B. Warranty Period: Written warranty, executed by manufacturer(s), agreeing to repair or replace components of standard and electrified door hardware that fails in materials or workmanship within specified warranty period after final acceptance by the Owner. Failures include, but are not limited to, the following:

1. Structural failures including excessive deflection, cracking, or breakage.

2. Faulty operation of the hardware.

3. Deterioration of metals, metal finishes, and other materials beyond normal weathering.

4. Electrical component defects and failures within the systems operation.

C. Standard Warranty Period: One year from date of Substantial Completion, unless otherwise indicated.

D. Special Warranty Periods:

1. Ten years for mortise locks and latches.

2. Five years for exit hardware.

3. Twenty five years for manual surface door closer bodies.

4. Five years for motorized electric latch retraction exit devices.

5. Two years for electromechanical door hardware.

1.8 MAINTENANCE SERVICE

A. Maintenance Tools and Instructions: Furnish a complete set of specialized tools and maintenance instructions as needed for Owner's continued adjustment, maintenance, and removal and replacement of door hardware.

PART 2 PRODUCTS

2.1 SCHEDULED DOOR HARDWARE

A. General: Provide door hardware for each door to comply with requirements in Door Hardware Sets and each referenced section that products are to be supplied under.

B. Designations: Requirements for quantity, item, size, finish or color, grade, function, and other distinctive qualities of each type of door hardware are indicated in the Door Hardware Sets at the end of Part 3. Products are identified by using door hardware designations, as follows:

C. Named Manufacturer's Products: Product designation and manufacturer are listed for each door hardware type required for the purpose of establishing requirements. Manufacturers' names are abbreviated in the Door Hardware Schedule.




2017)

D. Substitutions: Requests for substitution and product approval for inclusive mechanical and electromechanical door hardware in compliance with the specifications must be submitted in writing and in accordance with the procedures and time frames outlined in Division 01, Substitution Procedures. Approval of requests is at the discretion of the architect, owner, and their designated consultants.

2.2 HANGING DEVICES

A. Hinges: ANSI/BHMA A156.1 certified butt hinges with number of hinge knuckles as specified in the Door Hardware Sets.

1. Quantity: Provide the following hinge quantity, unless otherwise indicated:

a. Two Hinges: For doors with heights up to 60 inches.

b. Three Hinges: For doors with heights 61 to 90 inches.

c. Four Hinges: For doors with heights 91 to 120 inches.

d. For doors with heights more than 120 inches, provide 4 hinges, plus 1 hinge for every 30 inches of door height greater than 120 inches.

2. Hinge Size: Provide the following, unless otherwise indicated, with hinge widths sized for door thickness and clearances required:

a. Widths up to 3’0”: 4-1/2” standard or heavy weight as specified.

b. Sizes from 3’1” to 4’0”: 5” standard or heavy weight as specified.

3. Hinge Weight and Base Material: Unless otherwise indicated, provide the following:

a. Exterior Doors: Heavy weight, non-ferrous, ball bearing or oil impregnated bearing hinges unless Hardware Sets indicate standard weight.

b. Interior Doors: Standard weight, steel, ball bearing or oil impregnated bearing hinges unless Hardware Sets indicate heavy weight.

4. Hinge Options: Comply with the following where indicated in the Hardware Sets or on Drawings:

a. Non-removable Pins: Provide set screw in hinge barrel that, when tightened into a groove in hinge pin, prevents removal of pin while door is closed; for the all out-swinging lockable doors.

5. Acceptable Manufacturers:

a. Hager Companies (HA).

b. McKinney Products (MK).

B. Continuous Geared Hinges: ANSI/BHMA A156.26 Grade 1-600 certified continuous geared hinge. with minimum 0.120-inch thick extruded 6060 T6 aluminum alloy hinge leaves and a minimum overall width of 4 inches. Hinges are non-handed, reversible and fabricated to template screw locations. Factory trim hinges to suit door height and prepare for electrical cut-outs.


a. Ives (IV).

b. McKinney Products (MK).



DOOR HARDWARE


2017)

08 7100-7

c. Pemko Manufacturing (PE).

2.3 POWER TRANSFER DEVICES

A. Concealed Quick Connect Electric Power Transfers: Provide concealed wiring pathway housing mortised into the door and frame for low voltage electrified door hardware. Furnish with Molex™ standardized plug connectors and sufficient number of concealed wires (up to 12) to accommodate the electrified functions specified in the Door Hardware Sets. Connectors plug directly to through-door wiring harnesses for connection to electric locking devices and power supplies. Wire nut connections are not acceptable.


a. Pemko Manufacturing (PE) - EL-CEPT Series.

b. Securitron (SU) - EL-CEPT Series.

c. Von Duprin (VD) - EPT-10 Series.

B. Electric Door Wire Harnesses: Provide electric/data transfer wiring harnesses with standardized plug connectors to accommodate up to twelve (12) wires. Connectors plug directly to through-door wiring harnesses for connection to electric locking devices and power supplies. Provide sufficient number and type of concealed wires to accommodate electric function of specified hardware. Provide a connector for through-door electronic locking devices and from hinge to junction box above the opening. Wire nut connections are not acceptable. Determine the length required for each electrified hardware component for the door type, size and construction, minimum of two per electrified opening.

1. Provide one each of the following tools as part of the base bid contract:

a. McKinney Products (MK) - Electrical Connecting Kit: QC-R001.

b. McKinney Products (MK) - Connector Hand Tool: QC-R003.


a. McKinney Products (MK) - QC-C Series.

2.4 CYLINDERS AND KEYING

A. General: Cylinder manufacturer to have minimum (10) years’ experience designing secured master key systems and have on record a published security keying system policy.

B. Source Limitations: Obtain each type of keyed cylinder and keys from the same source manufacturer as locksets and exit devices, unless otherwise indicated.

C. Cylinders: Original manufacturer cylinders complying with the following:

1. Mortise Type: Threaded cylinders with rings and cams to suit hardware application.

2. Rim Type: Cylinders with back plate, flat-type vertical or horizontal tailpiece, and raised trim ring.

3. Bored-Lock Type: Cylinders with tailpieces to suit locks.

4. Mortise and rim cylinder collars to be solid and recessed to allow the cylinder face to be flush and be free spinning with matching finishes.

5. Keyway: Manufacturer’s Standard.




2017)

D. Patented Keyway Cylinders: ANSI/BHMA A156.5, Grade 1, certified cylinders employing a utility patented and restricted keyway requiring the use of patented controlled keys. Provide bump resistant, fixed core cylinders as standard with solid recessed cylinder collars. Cylinders are to be factory keyed where permanent keying records will be established and maintained.

1. Provide a 6 pin multi-level master key system comprised of patented controlled keys and security and high security cylinders operated by one (1) key of the highest level. Geographical exclusivity to be provided for all security and high security cylinders and UL437 certification where specified.

a. Level 1 Cylinders: Provide utility patented controlled keyway cylinders that are furnished with patented keys available only from authorized distribution.

b. Level 2 Cylinders: Provide utility patented controlled keyway and side bar locking incorporating unique angled bottom pins for geographical exclusivity. Cylinders constructed to provide protection against bumping and picking.

c. Level 3 Cylinders: Provide utility patented controlled keyway and side bar locking incorporating unique angled bottom pins for geographical exclusivity. Cylinders to be UL437 certified and constructed to provide protection against bumping, picking, and drilling.

d. Refer to hardware sets for specified levels.


a. Sargent Manufacturing (SA) - Degree DG1 or XC Series.

b. Corbin Russwin (RU) - Access 3 Series.

a. Medico 3 Rim + Mortise

b. To match system in existing Courthouse per Owner requirement.

E. Keying System: Each type of lock and cylinders to be factory keyed.

1. Conduct specified "Keying Conference" to define and document keying system instructions and requirements.

2. Furnish factory cut, nickel-silver large bow permanently inscribed with a visual key control number as directed by Owner.

3. New System: Key locks to a new key system as directed by the Owner.

F. Key Quantity: Provide the following minimum number of keys:

1. Change Keys per Cylinder: Two (2)

2. Master Keys (per Master Key Level/Group): Five (5).

3. Construction Keys (where required): Ten (10).

G. Construction Keying: Provide construction master keyed cylinders.

H. Key Registration List (Bitting List):

1. Provide keying transcript list to Owner's representative in the proper format for importing into key control software.



DOOR HARDWARE


2017)

08 7100-9

2. Provide transcript list in writing or electronic file as directed by the Owner.

I. Key Control Cabinet: Provide a key control system including envelopes, labels, and tags with self-locking key clips, receipt forms, 3-way visible card index, temporary markers, permanent markers, and standard metal cabinet. Key control cabinet shall have expansion capacity of 150% of the number of locks required for the project.


a. Lund Equipment (LU).

b. MMF Industries (MM).

c. Telkee (TK).

J. Key Control Software: Provide one network version of "Key Wizard" branded key management software package that includes one year of technical support and upgrades to software at no charge. Provide factory key system formatted for importing into “Key Wizard” software.

2.5 MECHANICAL LOCKS AND LATCHING DEVICES

A. Mortise Locksets, Grade 1 (Heavy Duty): ANSI/BHMA A156.13, Series 1000, Operational Grade 1 certified. Locksets are to be manufactured with a corrosion resistant steel case and be field-reversible for handing without disassembly of the lock body.


a. Corbin Russwin Hardware (RU) - ML2000 Series.

b. Sargent Manufacturing (SA) - 8200 Series.

c. Schlage (SC) - L9000 Series.

B. Multi-Point Locksets: Vertical rod locking devices designed for openings requiring multiple latching points within one locking mechanism. Rods are retracted by dual mounted outside lever trim controls available in a variety of ANSI/BHMA operational functions. Option for single top latching only eliminates the need for bottom strikes.


a. Corbin Russwin Hardware (RU) - MP9800 Series.


2.6 ELECTROMECHANICAL LOCKING DEVICES

A. Electromechanical Mortise Locksets, Grade 1 (Heavy Duty): Subject to same compliance standards and requirements as mechanical mortise locksets, electrified locksets to be of type and design as specified below.

1. Electrified Lock Options: Where indicated in the Hardware Sets, provide electrified options including: outside door lock/unlock trim control, latchbolt and lock/unlock status monitoring, deadbolt monitoring, and request-to-exit signaling. Support end-of-line resistors contained within the lock case. Unless otherwise indicated, provide electrified locksets standard as fail secure.

2. Energy Efficient Design: Provide lock bodies which have a holding current draw of 15mA maximum, and can operate on either 12 or 24 volts. Locks are to be field configurable for fail safe or fail secure operation.




2017)

3. High Security Monitoring: Provide lock bodies which have built-in request to exit monitoring and are provided with accompanying door position switches. Provide a resistor configuration which is compatible with the access control system.


a. Corbin Russwin Hardware (RU) - ML20900 Series.


c. Schlage (SC) - L9000 EL/EU/RX Series.

2.7 LOCK AND LATCH STRIKES

A. Strikes: Provide manufacturer's standard strike with strike box for each latch or lock bolt, with curved lip extended to protect frame, finished to match door hardware set, unless otherwise indicated, and as follows:

1. Flat-Lip Strikes: For locks with three-piece antifriction latchbolts, as recommended by manufacturer.

2. Extra-Long-Lip Strikes: For locks used on frames with applied wood casing trim.

3. Aluminum-Frame Strike Box: Provide manufacturer's special strike box fabricated for aluminum framing.

4. Double-lipped strikes: For locks at double acting doors. Furnish with retractable stop for rescue hardware applications.

B. Standards: Comply with the following:

1. Strikes for Mortise Locks and Latches: BHMA A156.13.

2. Strikes for Bored Locks and Latches: BHMA A156.2.

3. Strikes for Auxiliary Deadlocks: BHMA A156.36.

4. Dustproof Strikes: BHMA A156.16.

2.8 CONVENTIONAL EXIT DEVICES

A. General Requirements: All exit devices specified herein shall meet or exceed the following criteria:

1. At doors not requiring a fire rating, provide devices complying with NFPA 101 and listed and labeled for "Panic Hardware" according to UL305. Provide proper fasteners as required by manufacturer including sex nuts and bolts at openings specified in the Hardware Sets.

2. Where exit devices are required on fire rated doors, provide devices complying with NFPA 80 and with UL labeling indicating "Fire Exit Hardware". Provide devices with the proper fasteners for installation as tested and listed by UL. Consult manufacturer’s catalog and template book for specific requirements.

3. Except on fire rated doors, provide exit devices with hex key dogging device to hold the pushbar and latch in a retracted position. Provide optional keyed cylinder dogging on devices where specified in Hardware Sets.



DOOR HARDWARE


2017)

08 7100-11

4. Devices must fit flat against the door face with no gap that permits unauthorized dogging of the push bar. The addition of filler strips is required in any case where the door light extends behind the device as in a full glass configuration.

5. Electromechanical Options: Subject to same compliance standards and requirements as mechanical exit devices, electrified devices to be of type and design as specified in hardware sets. Include any specific controllers when conventional power supplies are not sufficient to provide the proper inrush current.

6. Lever Operating Trim: Where exit devices require lever trim, furnish manufacturer's heavy duty escutcheon trim with threaded studs for thru-bolts.

a. Lock Trim Design: As indicated in Hardware Sets, provide finishes and designs to match that of the specified locksets.

b. Where function of exit device requires a cylinder, provide a cylinder (Rim or Mortise) as specified in Hardware Sets.

7. Vertical Rod Exit Devices: Where surface or concealed vertical rod exit devices are used at interior openings, provide as less bottom rod (LBR) unless otherwise indicated. Provide dust proof strikes where thermal pins are required to project into the floor.

8. Narrow Stile Applications: At doors constructed with narrow stiles, or as specified in Hardware Sets, provide devices designed for maximum 2” wide stiles.

9. Dummy Push Bar: Nonfunctioning push bar matching functional push bar.

10. Rail Sizing: Provide exit device rails factory sized for proper door width application.

11. Through Bolt Installation: For exit devices and trim as indicated in Door Hardware Sets.

B. Conventional Push Rail Exit Devices (Heavy Duty): ANSI/BHMA A156.3, Grade 1 certified panic and fire exit hardware devices furnished in the functions specified in the Hardware Sets. Exit device latch to be stainless steel, pullman type, with deadlock feature.


a. Corbin Russwin Hardware (RU) - ED4000 / ED5000 Series.


c. Von Duprin (VD) - 35A/98 XP Series.

C. Tube Steel Removable Mullions: ANSI/BHMA A156.3 removable steel mullions with malleable-iron top and bottom retainers and a primed paint finish.

1. Provide keyed removable feature where specified in the Hardware Sets.

2. Provide stabilizers and mounting brackets as required.

3. Provide electrical quick connection wiring options as specified in the hardware sets.


a. Corbin Russwin Hardware (RU) - 700/900 Series.

b. Sargent Manufacturing (SA) - 980S Series.

c. Von Duprin (VD) - 9954 Series.




2017)

2.9 DOOR CLOSERS

A. All door closers specified herein shall meet or exceed the following criteria:

1. General: Door closers to be from one manufacturer, matching in design and style, with the same type door preparations and templates regardless of application or spring size. Closers to be non-handed with full sized covers including installation and adjusting information on inside of cover.

2. Standards: Closers to comply with UL-10C for Positive Pressure Fire Test and be U.L. listed for use of fire rated doors.

3. Cycle Testing: Provide closers which have surpassed 15 million cycles in a test witnessed and verified by UL.

4. Size of Units: Comply with manufacturer's written recommendations for sizing of door closers depending on size of door, exposure to weather, and anticipated frequency of use. Where closers are indicated for doors required to be accessible to the physically handicapped, provide units complying with ANSI ICC/A117.1.

5. Closer Arms: Provide heavy duty, forged steel closer arms unless otherwise indicated in Hardware Sets.

6. Closers shall not be installed on exterior or corridor side of doors; where possible install closers on door for optimum aesthetics.

7. Closer Accessories: Provide door closer accessories including custom templates, special mounting brackets, spacers and drop plates as required for proper installation. Provide through-bolt and security type fasteners as specified in the hardware sets.

B. Door Closers, Surface Mounted (Large Body Cast Iron): ANSI/BHMA A156.4, Grade 1 surface mounted, heavy duty door closers with complete spring power adjustment, sizes 1 thru 6; and fully operational adjustable according to door size, frequency of use, and opening force. Closers to be rack and pinion type, one piece cast iron body construction, with adjustable backcheck and separate non-critical valves for closing sweep and latch speed control.


a. Corbin Russwin Hardware (RU) - DC8000 Series.

b. LCN Closers (LC) - 4040XP Series.

c. Norton Door Controls (NO) - 9500 Series.

d. Sargent Manufacturing (SA) - 281 Series.

2.10 AUTOMATIC DOOR OPERATORS

A. General: Provide operators of size recommended by manufacturer for door size, weight, and movement; for condition of exposure; and for compliance with UL 325. Coordinate operator mechanisms with door operation, hinges, and activation devices.

1. Fire-Rated Doors: Provide door operators for fire-rated door assemblies that comply with NFPA 80 for fire-rated door components and are listed and labeled by a qualified testing agency.



DOOR HARDWARE


2017)

08 7100-13

B. Electrohydraulic Door Operators: Self-contained low-pressure units with rack and pinion design contained within a cast aluminum housing. Door closing speed controlled by independent hydraulic adjustment valves in the sweep and latch range of the closing cycle. Operator is to provide conventional door closer opening and closing forces unless the power operator motor is activated. Unit is to include an adjustable hydraulic backcheck valve to cushion the door speed if opened violently. Non-handed units for both push and pull side applications.

C. Brackets and Reinforcements: Manufacturer's standard, fabricated from aluminum with nonferrous shims for aligning system components.

D. Standard: Certified ANSI/BHMA A156.19.

1. Performance Requirements:

a. Opening Force if Power Fails: Not more than 15 lbf required to release a latch if provided, not more than 30 lbf required to manually set door in motion, and not more than 15 lbf required to fully open door.

b. Entrapment Protection: Not more than 15 lbf required to prevent stopped door from closing or opening.

E. Configuration: Surface mounted. Door operators to control single swinging and pair of swinging doors.

F. Operation: Power opening and spring closing operation capable of meeting ANSI A117.1 accessibility guideline. Provide time delay for door to remain open before initiating closing cycle as required by ANSI/BHMA A156.19. When not in automatic mode, door operator to function as manual door closer with fully adjustable opening and closing forces, with or without electrical power.

1. On-off switch to control power to be key switch operated.

G. Features: Operator units to have full feature adjustments for door opening and closing force and speed, backcheck, motor assist acceleration from 0 to 30 seconds, time delay, vestibule interface delay, obstruction recycle, and hold open time from 0 up to 30 seconds.

H. Provide outputs and relays on board the operator to allow for coordination of exit device latch retraction, electric strikes, magnetic locks, card readers, safety and motion sensors and specified auxiliary contacts.

I. Activation Devices: Provide activation devices in accordance with ANSI/BHMA A156.19 standard, for condition of exposure indicated and for long term, maintenance free operation under normal traffic load operation. Coordinate activation control with electrified hardware and access control interfaces. Activation switches are standard SPST, with optional DPDT availability.

J. Signage: As required by cited ANSI/BHMA A156.19 standard for the type of operator.


a. Horton Automatics (HO) - 4000 Series.

b. LCN Closers (LC) - 4640 Series.

c. Norton Door Controls (NO) - 6000 Series.




2017)

2.11 DOOR STOPS AND HOLDERS

A. General: Door stops and holders to be of type and design as specified below or in the Hardware Sets.

B. Door Stops and Bumpers: ANSI/BHMA A156.16, Grade 1 certified door stops and wall bumpers. Provide wall bumpers, either convex or concave types with anchorage as indicated, unless floor or other types of door stops are specified in Hardware Sets. Do not mount floor stops where they will impede traffic. Where floor or wall bumpers are not appropriate, provide overhead type stops and holders.


a. Ives (IV).

b. Rockwood Manufacturing (RO).

C. Overhead Door Stops and Holders: ANSI/BHMA A156.6, Grade 1 certified overhead stops and holders to be surface or concealed types as indicated in Hardware Sets. Track, slide, arm and jamb bracket to be constructed of extruded bronze and shock absorber spring of heavy tempered steel. Provide non-handed design with mounting brackets as required for proper operation and function.


a. Glynn Johnson (GJ).

b. Rixson Door Controls (RF).

c. Sargent Manufacturing (SA).

2.12 ARCHITECTURAL SEALS

A. General: Thresholds, weatherstripping, and gasket seals to be of type and design as specified below or in the Hardware Sets. Provide continuous weatherstrip gasketing on exterior doors and provide smoke, light, or sound gasketing on interior doors where indicated. At exterior applications provide non-corrosive fasteners and elsewhere where indicated.

B. Smoke Labeled Gasketing: Assemblies complying with NFPA 105 that are listed and labeled by a testing and inspecting agency acceptable to authorities having jurisdiction, for smoke control ratings indicated, based on testing according to UL 1784.

1. Provide smoke labeled perimeter gasketing at all smoke labeled openings.

C. Fire Labeled Gasketing: Assemblies complying with NFPA 80 that are listed and labeled by a testing and inspecting agency acceptable to authorities having jurisdiction, for fire ratings indicated, based on testing according to UL-10C.

1. Provide intumescent seals as indicated to meet UL10C Standard for Positive Pressure Fire Tests of Door Assemblies, and NPFA 252, Standard Methods of Fire Tests of Door Assemblies.

D. Sound-Rated Gasketing: Assemblies that are listed and labeled by a testing and inspecting agency, for sound ratings indicated.

E. Replaceable Seal Strips: Provide only those units where resilient or flexible seal strips are easily replaceable and readily available from stocks maintained by manufacturer.



DOOR HARDWARE


2017)

08 7100-15

F. Acceptable Manufacturers:

1. National Guard Products (NG).

2. Pemko Manufacturing (PE).

3. Reese Enterprises, Inc. (RE).

2.13 ELECTRONIC ACCESSORIES

A. Door Position Switches: Door position magnetic reed contact switches specifically designed for use in commercial door applications. On recessed models the contact and magnetic housing snap-lock into a 1" diameter hole. Surface mounted models include wide gap distance design complete with armored flex cabling. Provide SPDT, N/O switches with optional Rare Earth Magnet installation on steel doors with flush top channels.


a. Securitron (SU) - DPS Series.

B. Power Supplies: Provide Nationally Recognized Testing Laboratory Listed 12VDC or 24VDC (field selectable) filtered and regulated power supplies. Include battery backup option with integral battery charging capability in addition to operating the DC load in event of line voltage failure. Provide the least number of units, at the appropriate amperage level, sufficient to exceed the required total draw for the specified electrified hardware and access control equipment.


a. Securitron (SU) - BPS Series.

b. Von Duprin (VD) - PS.

2.14 FABRICATION

A. Fasteners: Provide door hardware manufactured to comply with published templates generally prepared for machine, wood, and sheet metal screws. Provide screws according to manufacturers recognized installation standards for application intended.

2.15 FINISHES

A. Standard: Designations used in the Hardware Sets and elsewhere indicate hardware finishes complying with ANSI/BHMA A156.18, including coordination with traditional U.S. finishes indicated by certain manufacturers for their products.

B. Provide quality of finish, including thickness of plating or coating (if any), composition, hardness, and other qualities complying with manufacturer's standards, but in no case less than specified by referenced standards for the applicable units of hardware

C. Protect mechanical finishes on exposed surfaces from damage by applying a strippable, temporary protective covering before shipping.




2017)

PART 3 EXECUTION

3.1 EXAMINATION

A. Examine scheduled openings, with Installer present, for compliance with requirements for installation tolerances, labeled fire door assembly construction, wall and floor construction, and other conditions affecting performance.

B. Notify architect of any discrepancies or conflicts between the door schedule, door types, drawings and scheduled hardware. Proceed only after such discrepancies or conflicts have been resolved in writing.

3.2 PREPARATION

A. Hollow Metal Doors and Frames: Comply with ANSI/DHI A115 series.

B. Wood Doors: Comply with ANSI/DHI A115-W series.

3.3 INSTALLATION

A. Install each item of mechanical and electromechanical hardware and access control equipment to comply with manufacturer's written instructions and according to specifications.

1. Installers are to be trained and certified by the manufacturer on the proper installation and adjustment of fire, life safety, and security products including: hanging devices; locking devices; closing devices; and seals.

B. Mounting Heights: Mount door hardware units at heights indicated in following applicable publications, unless specifically indicated or required to comply with governing regulations:

1. Standard Steel Doors and Frames: DHI's "Recommended Locations for Architectural Hardware for Standard Steel Doors and Frames."

2. Wood Doors: DHI WDHS.3, "Recommended Locations for Architectural Hardware for Wood Flush Doors."

3. Where indicated to comply with accessibility requirements, comply with ANSI A117.1 "Accessibility Guidelines for Buildings and Facilities."

4. Provide blocking in drywall partitions where wall stops or other wall mounted hardware is located.

C. Retrofitting: Install door hardware to comply with manufacturer's published templates and written instructions. Where cutting and fitting are required to install door hardware onto or into surfaces that are later to be painted or finished in another way, coordinate removal, storage, and reinstallation of surface protective trim units with finishing work specified in Division 9 Sections. Do not install surface-mounted items until finishes have been completed on substrates involved.

D. Thresholds: Set thresholds for exterior and acoustical doors in full bed of sealant complying with requirements specified in Division 7 Section "Joint Sealants."

E. Storage: Provide a secure lock up for hardware delivered to the project but not yet installed. Control the handling and installation of hardware items so that the completion of the work will not be delayed by hardware losses before and after installation.



DOOR HARDWARE


2017)

08 7100-17

3.4 FIELD QUALITY CONTROL

A. Field Inspection: Supplier will perform a final inspection of installed door hardware and state in report whether work complies with or deviates from requirements, including whether door hardware is properly installed, operating and adjusted.

3.5 ADJUSTING

A. Initial Adjustment: Adjust and check each operating item of door hardware and each door to ensure proper operation or function of every unit. Replace units that cannot be adjusted to operate as intended. Adjust door control devices to compensate for final operation of heating and ventilating equipment and to comply with referenced accessibility requirements.

3.6 CLEANING AND PROTECTION

A. Protect all hardware stored on construction site in a covered and dry place. Protect exposed hardware installed on doors during the construction phase. Install any and all hardware at the latest possible time frame.

B. Clean adjacent surfaces soiled by door hardware installation.

C. Clean operating items as necessary to restore proper finish. Provide final protection and maintain conditions that ensure door hardware is without damage or deterioration at time of owner occupancy.

3.7 DEMONSTRATION

A. Instruct Owner's maintenance personnel to adjust, operate, and maintain mechanical and electromechanical door hardware.

3.8 DOOR HARDWARE SETS

A. The hardware sets represent the design intent and direction of the owner and architect. They are a guideline only and should not be considered a detailed hardware schedule. Discrepancies, conflicting hardware and missing items should be brought to the attention of the architect with corrections made prior to the bidding process. Omitted items not included in a hardware set should be scheduled with the appropriate additional hardware required for proper application and functionality.

B. Manufacturer’s Abbreviations:

1. MK-McKinney

2. PE-Pemko

3. SA-Sargent

4. RO-Rockwood

5. RF-Rixson

6. NO-Norton

7. SU-Securitron




2017)

Hardware Schedule

Set: 1.0

Doors: 1034A, 1034D

2 Continuous Hinge CFM83SLI-HD1 PT x Height

Required PE

1 Exit Device DG3 53 55 56 AD8410 106 x Less

Pull US32D SA

1 Exit Device 53 55 56 AD8410 US32D SA

2 Pull RM201 Mtg-Type 1XHD US32D RO

2 Concealed Overhead Stop 1-X36 630 RF

1 Door Closer 281 P10 EN SA

1 Drop Plate 281D EN SA

1 Blade Stop Spacer 581-2 EN SA

1 Door Operator 6060 689 NO

1 Threshold 253x3AFG PE

1 Rain Guard 346A TKSP8 PE

2 Sweep 3452CNB TKSP8 PE

2 Electric Power Transfer EL-CEPT SU

2 ElectroLynx Harness QC-C1500P (Frame - EPT to

Power/Controller) MK

2 ElectroLynx Harness QC-CxxxP (Door - EPT to Elec. Exit

Device) MK

2 Position Switch DPS-M / W SU

2 Actuator 505 NO

1 Power Supply BPS-24-2 SU

1 Set Of Wiring Diagrams 00

Notes: Doors normally closed, latched and secure.

Entry by pull when doors electrically dogged down as programmed by access control system, actuators as

programmed by access control system or by key override.

Free egress at all times.

Weatherstripping provided by aluminum door supplier.

https://www.openingsstudio.com/AAOS/AAOS/CutSheetViewer.jsp?IDS=135578307,


https://www.openingsstudio.com/AAOS/AAOS/CutSheetViewer.jsp?IDS=73028572,20753919,



















DOOR HARDWARE


2017)

08 7100-19

Set: 2.0

Doors: 1034B, 1034C

2 Continuous Hinge CFM83SLI-HD1 PT x Height

Required PE

1 Exit Device DG3 53 55 56 AD8410 106 x Less

Pull US32D SA

1 Exit Device 53 55 56 AD8410 US32D SA

2 Pull RM201 Mtg-Type 1XHD US32D RO

2 Concealed Overhead Stop 1-X36 630 RF


1 Drop Plate 281D EN SA

1 Blade Stop Spacer 581-2 EN SA

1 Door Operator 6060 689 NO





Device) MK


2 Actuator 505 NO




Entry by pull when doors electrically dogged down as programmed by access control system, actuators as

programmed by access control system or by key override.

Remote pushbutton to override system and lock doors down.


Weatherstripping provided by aluminum door supplier.

Pushbutton provided by security contractor.




















2017)

Set: 3.0

Doors: 1040B, 1040C

2 Continuous Hinge CFM83HD1 PT x Height Required PE

1 Removable Mullion L980S PC SA

1 Fail Secure Electric Exit Device DG3 53 55 8876 ETL US32D SA

1 Exit Device 53 55 8810 ETL US32D SA

1 Cylinder DG3 980C1 US26D SA

2 Surface Overhead Stop 9-X36 630 RF

2 Door Closer 281 PD10 EN SA

2 Kick Plate K1050 10" x 2" LDW 4BE CSK US32D RO



1 Gasketing 2891APK TKSP8 PE

1 Mullion Gasketing 5110BL PE


2 Astragal 18041CNB TKSP8 PE





Device) MK




Notes: Doors normally closed, latched and secured.

Entry by valid card read or key override.


Card reader provided by security contractor.
























DOOR HARDWARE


2017)

08 7100-21

Set: 4.0

Doors: 1092, 1093


1 Exit Device DG3 53 55 8804 ETL US32D SA












Device) MK




Notes: Door normally closed, latched and secured.

Entry by key override. Latch bolt monitor (53-) to signal access control system that door is secured.

Request to exit switch (55-) to signal valid exit has occurred.





















2017)

Set: 5.0

Doors: 1074B


1 Fail Secure Electric Exit Device DG3 53 55 8876 ETL US32D SA












Device) MK




Notes: Door normally closed, latched and secure.






















DOOR HARDWARE


2017)

08 7100-23

Set: 6.0

Doors: 1033A


1 Removable Mullion L980S PC SA

2 Exit Device 53 55 8810 US32D SA

1 Cylinder DG3 980C1 US26D SA







1 Mullion Gasketing 5110BL PE







Device) MK





No entry - exit only doors.

























2017)

Set: 7.0

Doors: 1065B


1 Fail Secure Electric Lock DG3 LX RX 8273 LNL US26D SA











1 ElectroLynx Harness QC-CxxxP (Door - EPT to Elec.

Lock) MK






Egress by valid card read or key override.

Card reader on both sides of door provided by security contractor.



















DOOR HARDWARE


2017)

08 7100-25

Set: 8.0

Doors: 2084B














Lock) MK





Egress onto roof by valid card read or key override.

Free egress into stairwell at all times.


Set: 9.0

Doors: 1012

6 Hinge TA2714 4-1/2" x 4-1/2" US26D MK

2 Exit Device 12 NB8710 US32D SA

2 Door Closer 281 O EN SA


2 Wall Stop 400 US26D RO

1 Gasketing S88D PE

1 Astragal S772D PE



























2017)

Set: 10.0

Doors: 2044A

6 Hinge TA2714 4-1/2" x 4-1/2" US26D MK

1 Fail Secure Electric Exit Device 53 55 NB8774 ETL US32D SA

1 Exit Device DG3 53 55 NB8706 ETL US32D SA




1 Gasketing S88D PE






Exit Device) MK








Set: 11.0

Doors: 1033, 1081B, 1088

6 Hinge TA2714 4-1/2" x 4-1/2" US26D MK

2 Multi-Point Lock DG3 12 NB 701315 ETL US26D SA




1 Gasketing S88D PE


1 Removable Center Mullion (door 1081B only)

























DOOR HARDWARE


2017)

08 7100-27

Set: 12.0

Doors: 2048C

3 Hinge TA2714 4-1/2" x 4-1/2" US26D MK

1 Exit Device DG3 8804 ETL US32D SA




1 Gasketing S88D PE

Set: 13.0

Doors: 2013A, 2044C

3 Hinge TA2714 4-1/2" x 4-1/2" US26D MK

1 Fail Secure Electric Exit Device DG3 12 53 55 8876 ETL US32D SA




1 Gasketing S88D PE





Exit Device) MK






























2017)

Set: 14.0

Doors: 2047

3 Hinge TA2714 4-1/2" x 4-1/2" US26D MK

1 Fail Secure Electric Exit Device DG3 12 53 55 8876 ETL US32D SA




1 Gasketing S88D PE





Exit Device) MK








Set: 15.0

Doors: 2084A

3 Hinge TA2714 4-1/2" x 4-1/2" US26D MK

1 Fail Safe Electric Exit Device DG3 12 53 55 8875 ETL US32D SA




1 Gasketing S88D PE





Exit Device) MK
































DOOR HARDWARE


2017)

08 7100-29

Notes: Door normally closed, latched and unlocked.

Free egress and ingress under normal operation.

Remote push button to lock down stairwell side of door to limit access to corridor.

Entry by key override when door locked down.


Push button provided by security contractor.

Set: 16.0

Doors: 1084

3 Hinge TA2714 4-1/2" x 4-1/2" US26D MK

1 Exit Device 8815 ETL US32D SA




Set: 17.0

Doors: 2044B

3 Hinge TA2714 4-1/2" x 4-1/2" US26D MK

1 Exit Device DG3 8813 ETL US32D SA




Set: 18.0

Doors: 1080

3 Hinge TA2714 4-1/2" x 4-1/2" US26D MK





1 Gasketing S88D PE





Lock) MK



























2017)







Set: 19.0

Doors: 2034

3 Hinge TA2714 4-1/2" x 4-1/2" US26D MK





1 Gasketing S88D PE





Lock) MK
























DOOR HARDWARE


2017)

08 7100-31

Set: 20.0

Doors: 1064, 1065A, 1066

3 Hinge TA2714 4-1/2" x 4-1/2" US26D MK





1 Gasketing S88D PE





Lock) MK








Set: 21.0

Doors: 1065D

3 Hinge TA2714 4-1/2" x 4-1/2" US26D MK





1 Gasketing S88D PE





Lock) MK

































2017)



Egress by valid card read or key override.

Card reader both side of door provided by security contractor.

Set: 22.0

Doors: none

3 Hinge TA2714 4-1/2" x 4-1/2" US26D MK

1 Fail Safe Electric Lock DG3 LX RX 8270-24V LNL US26D SA




1 Gasketing S88D PE





Lock) MK






Remote push button to lock down corridor side of door to limit access to room.



















DOOR HARDWARE


2017)

08 7100-33

Set: 23.0

Doors: 1083

3 Hinge (heavy weight) T4A3786 5" x 4-1/2" US26D MK





1 Gasketing S88D PE





Lock) MK










Set: 24.0

Doors: 1081A, 1081B






1 Gasketing S88D PE





Lock) MK
































2017)








Set: 25.0

Doors: 1075, 1076A, 1076B, 2019, 2028, 2028A, 2048A

3 Hinge TA2714 4-1/2" x 4-1/2" US26D MK

1 Storeroom Lock DG3 8204 LNL US26D SA




1 Gasketing S88D PE

Set: 26.0

Doors: 1032, 1062A, 2049

3 Hinge TA2714 4-1/2" x 4-1/2" US26D MK





1 Gasketing S88D PE

Set: 27.0

Doors: 1014






1 Gasketing S88D PE





















DOOR HARDWARE


2017)

08 7100-35

Set: 28.0

Doors: 2048B






1 Gasketing S88D PE

Set: 29.0

Doors: 1029, 1077, 1078A

3 Hinge TA2714 4-1/2" x 4-1/2" US26D MK

1 Office Lock DG3 8205 LNL US26D SA




1 Gasketing S88D PE

Set: 30.0

Doors: 1025

3 Hinge TA2714 4-1/2" x 4-1/2" US26D MK





1 Gasketing S88D PE

Set: 31.0

Doors: 2042, 2043

3 Hinge TA2714 4-1/2" x 4-1/2" US26D MK

1 Passage Set 8215 LNL US26D SA




1 Gasketing S88D PE




























2017)

Set: 32.0

Doors: 2033B

3 Hinge TA2714 4-1/2" x 4-1/2" US26D MK





1 Gasketing S88D PE

Set: 33.0

Doors: 1027, 1028

3 Hinge TA2714 4-1/2" x 4-1/2" US26D MK

1 Privacy Set 49 8265 LNL US26D SA




1 Gasketing S88D PE

Set: 34.0

Doors: 1079

3 Hinge TA2714 4-1/2" x 4-1/2" US26D MK





1 Gasketing S88D PE





















DOOR HARDWARE


2017)

08 7100-37

Set: 35.0

Doors: 1015

3 Hinge TA2714 4-1/2" x 4-1/2" US26D MK





1 Gasketing S88D PE





Lock) MK










Set: 36.0

Doors: 1042, 1067

3 Hinge TA2714 4-1/2" x 4-1/2" US26D MK

1 Classroom Lock DG3 8237 LNL US26D SA




Set: 37.0

Doors: 2034B

3 Hinge TA2714 4-1/2" x 4-1/2" US26D MK



























2017)

Set: 38.0

Doors: 1039, 1062

3 Hinge TA2714 4-1/2" x 4-1/2" US26D MK





Set: 39.0

Doors: 1061, 1070

3 Hinge TA2714 4-1/2" x 4-1/2" US26D MK





Set: 40.0

Doors: none

3 Hinge TA2714 4-1/2" x 4-1/2" US26D MK





Set: 41.0

Doors: 1087




























DOOR HARDWARE


2017)

08 7100-39

Set: 42.0

Doors: 2012, 2020B




Set: 43.0

Doors: 1085, 2015, 2016, 2017, 2018, 2023, 2024, 2025, 2026, 2027, 2030, 2033A, 2038, 2039, 2040,

2041, 2046, 2050, 2051

3 Hinge TA2714 4-1/2" x 4-1/2" US26D MK



Set: 44.0

Doors: 1078B

3 Hinge TA2714 4-1/2" x 4-1/2" US26D MK





Set: 45.0

Doors: 1035

3 Hinge TA2714 4-1/2" x 4-1/2" US26D MK
























2017)

Set: 46.0

Doors: 2045

3 Hinge TA2714 4-1/2" x 4-1/2" US26D MK





Set: 47.0

Doors: 1021B, 1022B, 1023B, 1024B

3 Hinge TA2714 4-1/2" x 4-1/2" US26D MK



Set: 48.0

Doors: 2032

3 Hinge TA2714 4-1/2" x 4-1/2" US26D MK






Set: 49.0

Doors: 1036, 1037, 1038, 1042A, 1048, 1082, 2011, 2035, 2036

3 Hinge TA2714 4-1/2" x 4-1/2" US26D MK






















DOOR HARDWARE


2017)

08 7100-41

Set: 50.0

Doors: 1069, 1071

3 Hinge TA2714 4-1/2" x 4-1/2" US26D MK





Set: 51.0

Doors: 1010B, 1053C, 1053D, 1065C

1 Cylinder DG3 x Type Required US32D SA

1 Balance of hardware supplied with

door 00

Set: 52.0

Doors: 1033B

2 Hinge TA2714 4-1/2" x 4-1/2" US26D MK



Mark Hardware

1010B 51.0

1012 9.0

1014 27.0

1015 35.0

1017 22.0

1018 22.0

1019 22.0

1020 22.0

1021B 47.0

1022B 47.0

1023B 47.0

1024B 47.0

1025 30.0

1027 33.0

1028 33.0

1029 29.0













2017)

1032 26.0

1033 6.0

1033A 40.0

1034A 1.0

1034B 2.0

1034C 2.0

1034D 1.0

1035 45.0

1036 49.0

1037 49.0

1038 49.0

1039 38.0

1040B 3.0

1040C 3.0

1042 36.0

1042A 49.0

1048 49.0

1053C 51.0

1053D 51.0

1061 39.0

1062 38.0

1062A 26.0

1065B 7.0

1065C 51.0

1065D 21.0

1066 20.0

1067 36.0

1069 50.0

1070 39.0

1071 50.0

1074B 5.0

1075 25.0

1076A 25.0

1076B 25.0

1077 29.0

1078A 29.0

1078B 44.0

1079 34.0

1080 18.0

1081A 24.0

1081B 24.0

1082 49.0



DOOR HARDWARE


2017)

08 7100-43

1083 23.0

1084 16.0

1085 43.0

1087 41.0

1088 11.0

1092 4.0

1093 4.0

2011 49.0

2012 42.0

2013A 13.0

2015 43.0

2016 43.0

2017 43.0

2018 43.0

2019 25.0

2020B 42.0

2023 43.0

2024 43.0

2025 43.0

2026 43.0

2027 43.0

2028 25.0

2028A 25.0

2030 43.0

2032 48.0

2033A 43.0

2033B 32.0

2034 19.0

2034B 37.0

2035 49.0

2036 49.0

2038 43.0

2039 43.0

2040 43.0

2041 43.0

2042 31.0

2043 31.0

2044A 10.0

2044B 17.0

2044C 13.0

2045 46.0

2046 43.0




2017)

2047 14.0

2048A 25.0

2048B 28.0

2048C 12.0

2049 26.0

2050 43.0

2051 43.0

2084A 15.0

2084B 8.0

END OF SECTION


FOODSERVICE

EQUIPMENT Project # 4163150 07-14-2017

(Addenda #2 Issue date 08-08-2017

11 4000-1

SECTION 11 4000

FOODSERVICE EQUIPMENT – REVISED ADDENDUM #2

PART 1 - GENERAL

1.1 RELATED DOCUMENTS

A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section.

1.2 SUMMARY

A. This Section includes equipment for foodservice facilities indicated on the Drawings.

B. Related Sections include the following:

1. Division 03 Section "Cast-in-Place Concrete" for the following:

a. Requirements for slab depressions. (Walk-in Freezer/Cooler)

2. Division 05 Section "Metal Fabrications" for equipment supports.

3. Division 22 & 23 Sections “Mechanical” for plumbing and HVAC systems.

4. Division 26 Section “Electrical” for general electrical systems.

5. Division 21, 22, and 23 Sections for supply and exhaust fans; exhaust ductwork; service roughing-ins; drain traps; atmospheric vents; valves, pipes, and fittings; fire-extinguishing systems; and other materials required to complete foodservice equipment installation.

6. Division 23 Section "Commercial Kitchen Hoods" for ventilation hoods.

7. Division 26 Sections for connections to fire alarm systems, wiring, disconnect switches, and other electrical materials required to complete foodservice equipment installation.

8. PLUMBING DEVICES, FAUCETS, VALVES, FITTINGS, TEMPERATURE REGULATORS, AND SIMILAR ITEMS, shall be furnished and installed by the Plumbing Subcontractor unless specified in the Itemized Specifications.

9. ELECTRICAL EQUIPMENT AND DEVICES, SWITCHES, STARTERS, AND CONTROLS, in fabricated equipment items shall be factory installed and of the proper type in accordance with the National Electrical Code. All devices shall be listed or recognized by Underwriters’ Laboratories, Inc. Set controls that are mounted on vertical surfaces of fabricating fixtures, into recessed die - stamped stainless steel cups or otherwise indent to prevent damage. EC shall provide electrical devices not supplied or specified herein.

1.3 DEFINITIONS & ABBREVIATIONS

A. NATIONAL SANITATION FOUNDATION (NSF). Construct Equipment in compliance with the standards of the National Sanitation Foundation and in full compliance with the Public Health Regulations of the County and State. Each piece of equipment shall have the “seal of approval” label of the National Sanitation Foundation.


FOODSERVICE EQUIPMENT Bid Package #4 VE Coordination

11 4000-2 07-14-2017 (Addenda #2 issue date 08-08-2017)

1.4 REGULATIONS AND STANDARDS

A. Construct equipment in compliance with the following applicable codes, regulations, and standards. In case of conflict between the following standards, the most stringent requirements shall govern:

1. Americans with Disabilities Act (ADA).

2. American Gas Association (AGA).

3. American National Standards Institute (ANSI).

4. American Society of Heating, Refrigerating and Air-Conditioning Engineers (ASHRAE).

5. American Society of Mechanical Engineers (ASME).

6. American Society for Testing and Materials (ASTM).

7. National Electrical Code (NEC).

8. National Electrical Manufacturers Association (NEMA)

9. National Fire Protection Association (NFPA). 10. Underwriters Laboratories Inc. (UL)

1.5 ABBREVIATIONS

A. In accordance with the Construction Manager’s (CMa) bid categories, the following Sub-contractors with related Work, which shall not be limited to the partial list, are:

1. EC - Electrical Sub-contractor

2. FSEC - Foodservice Equipment Sub-contractor

3. HVAC - Heating, Ventilating and Air Conditioning Sub-contractor

4. PC - Plumbing Sub-contractor

5. MC - Mechanical Sub-contractor

1.6 SUBMITTALS

A. Product Data: For each type of product indicated. Include the following:

1. Manufacturer's model number.

2. Options, accessories, and components that will be included for Project.

3. Clearance requirements for access and maintenance.

4. Utility service connections for water, drainage, power, and fuel; include roughing-in dimensions.

B. Shop Drawings: For fabricated equipment and special needs as required within these written specifications for successful project completion. Include plans, elevations, sections, roughing-in dimensions, fabrication details, utility service requirements, and attachments to other work.

C. Coordination Drawings: For foodservice facilities.

1. Indicate locations of foodservice equipment and connections to utilities.

2. Key equipment using same designations as indicated on Drawings.

3. Include plans and elevations; clearance requirements for equipment access and maintenance; details of support for equipment; and utility service characteristics.

4. Include details of seismic bracing for equipment if required by local code.

D. Samples for Initial Selection: For units with factory-applied color finishes.

E. Samples for Verification: For each factory-applied color finish required, in manufacturer's standard sizes.



FOODSERVICE

EQUIPMENT 07-14-2017


11 4000-3

F. Operation and Maintenance Data: For foodservice equipment to include in emergency, operation, and maintenance manuals. In addition to items specified in Division 01 Section "Closeout Procedures & Operation and Maintenance Data," include the following:

1. Product Schedule: For each foodservice equipment item, include the following:

a. Designation indicated on Drawings.

b. Manufacturer's name and model number.

c. List of factory-authorized service agencies including their addresses and telephone numbers.

G. Warranty: Special warranty specified in this Section.


A. NSF Standards: Provide equipment that bears NSF Certification Mark or UL Classification Mark certifying compliance with applicable NSF/ANSI standards.

B. BISSC Standards: Provide bakery equipment that complies with BISSC's "Sanitation Standards for the Design and Construction of Bakery Equipment and Machinery."

C. UL Certification: Provide electric and fuel-burning equipment and components that are evaluated by UL for fire, electric shock, and casualty hazards according to applicable safety standards and that are UL certified for compliance and labeled for intended use.

D. Steam Equipment: Provide steam-generating and direct-steam heating equipment that is fabricated and labeled to comply with ASME Boiler and Pressure Vessel Code.

E. Regulatory Requirements: Install equipment to comply with the following:

1. ASHRAE 15, "Safety Code for Mechanical Refrigeration."

2. NFPA 54, "National Fuel Gas Code."

3. NFPA 70, "National Electrical Code."

4. NFPA 96, "Ventilation Control and Fire Protection of Commercial Cooking Operations."

F. Seismic Restraints: Comply with SMACNA's "Kitchen Ventilation Systems and Food Service Equipment Fabrication and Installation Guidelines," Appendix A, "Seismic Restraint Details," if required by code unless otherwise indicated.

G. Pre-installation Conference: Conduct conference at Project site to comply with requirements in Division 01 Section "Project Management and Coordination."

1.8 PROJECT CONDITIONS

A. Field Measurements: Indicate measurements on Coordination Drawings.

1.9 COORDINATION

A. Coordinate foodservice equipment layout and installation with other work including electrical, mechanical equipment, plumbing equipment, and fire-suppression system components.

B. Coordinate location and requirements of utility service connections.

C. Coordinate size, location, and requirements of the following:

1. Overhead equipment supports.

2. Equipment bases.

3. Floor depressions.




4. Insulated floors.

5. Floor areas with positive slopes to drains.

6. Floor sinks and drains serving foodservice equipment.

7. Roof curbs, equipment supports, and penetrations.

8. Equipment that requires thru-wall or in-wall installation.

D. MECHANICAL AND ELECTRICAL ROUGH-INS. Examine roughed-in mechanical and electrical services, and installation of floors, walls, columns and conditions under which the work is to be installed. Notify the Construction Manager and Trade Sub-contractor of unsatisfactory conditions for proper installation of food service equipment.

1. Visit the job site to check mechanical and electrical rough-ins, prior to the installation of concrete floor.

2. Cost to relocate or add utility lines due to failure of the Foodservice Equipment Contractor Subcontractor to indicate their proper location on the rough-in shop drawings, will be assumed by the Foodservice Sub-Contractor.

3. THOUROUGHLY REVIEW Architectural, Mechanical and Electrical Drawings, and visit the project site as necessary to coordinate construction of all partitions prior to delivery of food service equipment.

4. PROVIDE information to all trades at an early date a list of all equipment requirements that are relevant to that trade. Assist with hook-ups as necessary.

E. GENERAL INFORMATION CONCERNING EQUIPMENT AND WALK-IN INSTALLATION

1. FSEC shall ASSEMBLE AND ERECT ALL EQUIPMENT ITEMS in the locations shown on the Drawings. Set up items plumb and level, ready for final plumbing, electrical, and ventilating connections.

2. FSEC shall seal BETWEEN WALLS and dissimilar materials. For example at sinks, tables, and dish tables where backsplashes sit against walls. Sealant shall be appropriate for each specific location or application. Sealant shall be CLEAR silicone, applied in a narrow smooth bead, unless specific circumstances or condition merit a different application.

3. FSEC shall INSTALL CLOSURE PANELS, TRIM STRIPS, and WALL FLASHING where required with matching metal using mastic or other fastener made of stainless steel or non-corrosive material. Trim Strips at top of backsplashes are not permitted. Equipment must fit within ¼” of walls.

4. MC shall INSTALL INTERCONNECTING REFRIGERATION PIPING and insulation required for the walk-in cooler/freezer. All piping and insulation routed in the ceiling plenum shall comply with ASTM E-84 flame spread 25/smoke density-50). COORDINATE installation with general contractor.

5. FSEC shall COMPLETE ERECTION OF ALL WALK-IN PANELS, including all necessary sealant.

6. FSEC shall INSTALL BEAM AND POST SECTIONS in accordance with manufacturer’s recommendations in the location indicated on the plan if required.



FOODSERVICE



11 4000-5

7. EC shall MOUNT ALL INTERIOR CEILING LIGHTS where indicated. EC to wire all lights to “J” boxes and wire freezer condenser and evaporator, with defrost timer. EC shall also wire all other components, such as alarms, pressure relief ports, door & window heaters, etc.

8. FSEC shall HANG EVAPORATOR COILS where indicated on drawing.

9. FSEC shall coordinate and SET CONDENSING UNITS WHERE INDICATED. Coordinate with Roofing Sub-contractor. FSEC shall install all refrigeration lines. EC to install electrical wiring between condensing unit and evaporator coils and make final connections. EC to inter-wire freezer condenser and evaporator with time clock.

10. MC/PC to INSTALL HEAT TAPE and INSULATION ON FREEZER and COOLER DRAIN LINES and INSULATE REFRIGERATION LINES.

11. Review this item with the plumbing sub-contractor to insure correct installation. COPPER CONDENSATE line from evaporator to discharge outside of walk-in. Furnish “P” trap in drain line outside of freezer. Furnish drain line heater in freezer before insulating drain line. “T” freezer drain line with cooler drain line inside of cooler and discharge outside of walk-in. PLUMBING CONTRACTOR shall provide and install copper drain lines from evaporators to floor sink. Plumbing contractor to provide and install heat tape and insulation for drain lines. PC to provide a P-trap on drain line at exterior of freezer/cooler ahead of termination at floor sink.

12. FSEC shall FOAM ALL PENETRATIONS before sealing with silicone.

13. FSEC shall TAG AND LABEL ALL KEYS with plastic identification tags and deliver to the owner.

14. EC to make all necessary electrical connections to switches, lights, condensers, evaporators, pressure relief ports, door heaters, etc. to insure a complete installation per manufacturer instructions.

15. EC shall wire lights and fan switches on exhaust hood. EC to provide shunt trip.

16. EC shall provide conduit from the Ansul system to the pull-down station.

17. Mechanical gas shunt trip valve to be provided by the FSEC to the PC.

1.10 TESTING AND DEMONSTRATING EQUIPMENT

A. DELAY START-UP of food service equipment until lines have been tested, balanced, and adjusted for pressure, voltage and similar considerations; and until water lines have been cleaned and treated for sanitation.

B. TEST EACH EQUIPMENT ITEM to demonstrate that it is operating properly, and that controls and safety devices are functioning. Repair or replace equipment that is found to be defective or operating with excess noise or vibration.

C. FINAL TEST AND DEMONSTRATION OF EQUIPMENT shall be conducted by the Food Service Equipment Subcontractor in the presence of the Owner or his representative after all connections have been made. Notify the architect and consultant of start-up and demonstration dates. Qualified technicians (Manufacturers Representatives) shall instruct Owner personnel in proper function, adjustment methods, maintenance and care of each piece of equipment herein specified, to the complete satisfaction of the Owner. The respective manufacturer’s representative shall demonstrate all cooking equipment. FSEC project manager needs to be present at time of all demonstrations.




D. SCHEDULE DEMONSTRATION OF EQUIPMENT with Owner. Provide written notice of demonstration date to the Architect and Construction Manager, at a minimum of 14 days prior the scheduled date.

PART 2 - PRODUCTS

2.1 MANUFACTURERS

A. In other Part 2 articles where titles below introduce lists, the following requirements apply to product selection:

1. Available Products: Subject to compliance with requirements, products that may be incorporated into the Work include, but are not limited to, products specified.

2. Products: Subject to compliance with requirements, provide one of the products specified. If only one product is specified provide that product only.

3. Available Manufacturers: Subject to compliance with requirements, manufacturers’ offering products that may be incorporated into the Work include, but are not limited to, manufacturers specified.

4. Manufacturers: Subject to compliance with requirements, provide products by one of the manufacturers specified. If only one product is specified provide that product only.

5. Basis-of-Design Product: The design for foodservice equipment item is based on the product named. Subject to compliance with requirements, provide either the named product or a comparable product by one of the other manufacturers specified.

6. All equipment shall be the latest manufacturers’ model. Equipment specified by model number shall include all standard and any optional accessories as specified.

7. All equipment including custom and/or customized equipment shall each have a model number that includes the code *M125 or *M127 as a suffix. This code is known as the Specifier Identification System. It is not to be removed by the bidders. Its purpose is to identify the specifier to the vendors providing equipment in the event it is necessary to communicate questions, clarifications and comments, from prior to bid award through the final purchase. It is to be used on all correspondence including fax and email when communicating with manufacturers’ representatives and factories.

B. All equipment specified herein shall be basis of design products unless noted as “No Substitution”. Foodservice Equipment Contractor shall submit for approval all requests for substitution against basis of design product at least two weeks prior to bid submittal.

2.2 FABRICATED EQUIPMENT

A. Where specifications state a basis-of-design product or Custom Fabricator in the manufacturer category, the FSEC can select a fabricator who will build the piece of equipment around the specifications of the basis-of-design product providing that the fabricator produce shop drawings for submittal and that the fabricator meets the requirements as specified in this section and as described below.

B. Plant, Personnel and Facilities. Fabricated equipment described in the following specifications other than by name or catalog numbers, shall be manufactured by an equipment fabricator who has the plant, personnel and engineering facilities to properly design, detail and manufacture high quality foodservice equipment. The fabricator is subject to the approval of the architect and consultant.



FOODSERVICE



11 4000-7

C. The fabricator shall have been engaged in the manufacture and distribution of foodservice equipment for the past ten years, or longer, as required under the Contract, as his principal product.

D. Standard products and materials specified herein shall be furnished by manufacturers regularly engaged in the production of such materials, products and equipment and shall be of the manufacturers latest design that complies with the written specifications.

E. A competent foreman or supervisor and qualified workers shall be provided for installation of equipment and to counsel with other trades in regard to the installation and connections.

F. Materials:

1. Stainless Steel: ASTM A 666, with No. 4 finish (directional satin finish) on exposed surfaces.

2. Galvanized Steel: ASTM A 653/A 653M, G90 coating designation; commercial-quality, cold-rolled steel that is zinc coated by the hot-dip process and chemically treated.

2.3 ITEMIZED SPECIFICATIONS

A. Item No. A111401 - Sink, Mop

1. Basis of Design Product: Advance Tabco Model 9-OP-40 A

2. Available Manufacturers: Universal Stainless, Two Rivers Fabrication

3. Mop Sink, floor mounted, 20" Left to Right, 16" Front to Back, 12" high water level, 2" drain, stainless steel construction. Provide (1) Service Faucet, (1) Mop Drip Tray and (1) Hose & Hanger. Furnish (1) Utility Shelf, 8" wide x 36" long.

B. Item No. A111402 - Floor Trough

1. Basis of Design Product: Eagle Group Model FT-2436-FG


3. Floor Trough, 24" x 36", 14 gauge type 304 stainless steel all-welded construction, built-in pitch, secured with anchor straps, stainless steel waste cup with removable stainless steel basket, accommodates up to 4" diameter waste pipe, subway style fiberglass grating.

C. Item No. A111403 - Cleaning System, Pressure

1. Spray Master Model 300-WAL-5107 NO SUBSTITUTIONS

2. SMT-600-W Wall Mount Pressure Washer Cleaning System, 2.2gpm @ 1100psi, 115v, adjustable chemical & sanitizer injectors, 3 cylinder CAT plunger pump, SMT-200-RW manual rewind hose reel, 50' hi-pressure hose, 36" spray gun assembly, Flo-Thru quick disconnects, pressure gauge, stainless steel cover & frame, (2) 1 gallon chemical baskets. Provide Warranty - Two year parts & one year labor.

D. Item No. A111404 - Tray Rack - Cold Food Trays

1. Food Warming Equip Model RRB-26 NO SUBSTITUTIONS

2. Rethermalizer/Holding Roll-In Rack, for RH-RB-26 & 26 HO, capacity 26 wire baskets, Stainless steel construction, 5" casters.




E. Item No. A111405 - Shelving Unit, Starter, Metal, Wire

1. Basis of Design Product: Eagle Group Model S4-74-2460E

2. Available Manufacturers: Metro

3. Wire Shelving Starter Unit, (4) 24"W x 48"L wire shelves, (2) 24"Wx36"L, (6) 74"H posts, green epoxy finish with antimicrobial protection, NSF approved.

F. Item No. A111406 - Shelving Unit, Starter, Metal, Wire



3. Wire Shelving Starter Unit, (4) 18"W x 60"L wire shelves, (4) 74"H posts, green epoxy finish with antimicrobial protection, NSF approved.

G. Item No. A111407 - Shelving, Wire



3. Wire Shelving, 24"W x 48"L, green epoxy finish w/MICROGARD™ antimicrobial protection, NSF. Provide Mobile Unit Kit, single density, for 24"W unit, includes: 74" posts, casters, all parts & hardware for one unit, green epoxy finish. Furnish (2) Stationary End/intermediate Unit Kit, single density, all hardware & 74" post for connecting one stationary end or intermediate unit to track, green epoxy finish, MUST BE ANCHORED TO FLOOR. Provide (1) Overhead Track Kit, single density, 18.5 ft. Delete per addendum #2; VE Coordination documents.

H. Item No. A111408 - Walk-In Combination Cooler/Freezer

1. Thermo-Kool (Mid South Industries) NO SUBSTITUTION Model: TK

2. Description: Two-compartment unit, with (1) cooler and (1) freezer compartments. Actual 12'-8" x 19'-0" x 8'-6"H, field verify. Unit shall be furnished with insulated 4” thick floor panels that will be recessed into the floor and top-coated with concrete and resinous coating (by others).

a. Wall, Floor and Ceiling Panels: Interlocking insulating panels.

1) All panels shall consist of metal pans formed to precise dimensions. Insulation shall be “foamed in place”, 4” thick, low ozone depleting HCFC 22 blown Class I urethane foam classified according to UL723 (ASTM-E-84) as tested by UL, Inc. The 4” core material shall have a flame spread of 25 or less and a smoke density of 250 or less.

2) The urethane foam is foamed in-place to bond to the inner surfaces of metal pans having a thermal conductivity (k-factor) of not more than 0.125 BTU/hr/sq. ft. per degrees Fahrenheit, and, an overall coefficient of heat transfer (U factor) of no more than .031. The R factor shall be 32. The prefabricated urethane foam panels shall be supplied with a Class I fire hazard classification according to UL723 (ASTM-E-84) as tested by UL, Inc. Panels shall have a flame spread rating of 25 or less with a certifying UL, Inc. label.

3) Perimeter of panels shall be formed of pre-formed high-density urethane. High- density perimeters will prevent cam locks from stretching during installation, assure vapor and air-tight joints, increase dimensional stability to minimize the possibility of panel deflection and to help prevent pre-installation damage and panel deterioration due to moisture at seams.



FOODSERVICE



11 4000-9

4) Panels shall be covered by a ten year warranty.

5) Panel locking assemblies shall be self-aligning and self-centering pin assembly sets. Rotation of cam-action arm shall pull and lock panels together. Locking devices must be secured in high-density perimeters to insure proper seal. Locking devices in low-density foam perimeters secured by barbed anchors will not be accepted. Provide a minimum of three locks per vertical seam.

6) Panel gaskets shall be NSF approved double-beaded vinyl.

b. Doors: (2) 34” x 76”. Doors shall be flush mounted and UL listed. Each door shall be equipped with one PVC accordion type removable gasket with magnetic core at top and along the side perimeter. An adjustable wiper gasket shall be mounted along the bottom edge of each door. A 14 gauge reinforced steel “U” channel frame with integrally welded backup plates for hinges is to encompass the entire perimeter of the door opening and be foamed in place to give extra rigidity and support to the frame to prevent racking, distortion, warping and twisting of the door. Door swing shall be as close to 180 degrees as possible.

1) Hinges: Self-closing and spring loaded; two (2) per door. 9” modified strap, cam- lift design hinges with lift-off capability made of high-pressure zinc die cast highly polished chrome.

2) Latch: Edge-mounted, positive-type latch with cylinder lock.

(a) Include safety-release handle that opens door from inside when door is locked.

c. Options and Accessories:

1) Vision port. Provide 14” x 14” peep windows in each door.

2) Pressure relief port.

3) Anti-condensate heater at freezer doors must be located behind a removable heavy gauge stainless steel trim for easy access.

4) Kick-plates: On all doors, Interior and Exterior, aluminum tread-plate 36”H.

5) Two (2) vinyl strip curtains to fit 34” x 76” opening.

4. Exposed Exterior Finish: 20 gauge, Type 304, #3 Finish, Stainless Steel.

5. Unexposed Exterior Finish: .040 Stucco Aluminum

6. Interior Finish: Stucco Aluminum

7. Ceiling: White Stucco Aluminum

8. Vapor-proof Lighting Fixtures: Incandescent fixture.

a. Control: Neon pilot light and toggle switch located on exterior of door panel.

b. Quantity: One per compartment, located on door panel.

c. Provide (4) fluorescent light fixtures (2 for cooler, 2 for freezer).




9. Refrigeration System Freezer: Item #8.4 - Thermo-Kool Model MOHO31L63: Air-cooled condensing unit, pre-wired, preassembled, remote, low temperature. Condensing Unit Amps: 14.38. R-404A Refrigerant, sealed hermetic, 11,540 BTU capacity @ -10F Room Temp. 3 HP, 208-230/60/3. Provide (Item #8.3) Evaporator coil Model SME-1301, 208- 230/60/1, Amps: 1.5. Operating Temperature: -10 degree F.

10. Refrigeration System Cooler: Item #8.2 - Thermo-Kool Model MOHO15X63: Air-cooled condensing unit, pre-wired, preassembled, remote, medium temperature. Condensing Unit Amps: 9.4. R-404A Refrigerant, sealed hermetic, 15,090 BTU capacity @ 35F Room Temp. 1.5 HP, 208-230/60/3. Provide (Item #8.1) Evaporator coil Model SM-1340, 115/60/1, Amps: 2.7. Operating Temperature: 38 degree F.

11. Temperature Monitoring System: Provide (2) Audio/Visual Alarm System devices.

a. Weiss, Model XWA11V-4N1FO, alarm and light managers with 5’-0” temp. probe, magnetic switch, and external buzzer. Electronic monitoring and remote audible alarm system that warns when temperatures exceed 10 deg F above or below set temperature. Furnish (2) two illuminated mushroom buttons, mounted, wired to Weiss alarm system to create a panic alarm.

12. Closure Panels and Trim: Match exposed exterior finish of panels for both sides to walls and top to ceiling. Verify Finished Ceiling height.

13. Furnish control kit to include; Expansion valve, dryer, sight glass, temperature control, pump down solenoid valve, freezer time clock, pressure control, suction line vibration eliminator, and coil mounting kit.

I. Item A111408 (Sub Item No. 08.1) - Evaporator, Cooler

1. Thermo-Kool Model TK - SEE ITEM #08

2. Evaporator, Cooler

J. Item A111408 (Sub Item No. 08.2) - Condenser, Cooler


2. Condenser, Cooler

K. Item A111408 (Sub Item No. 08.3) - Evaporator, Freezer


2. Evaporator, Freezer

L. Item A111408 (Sub Item No. 08.4) - Condenser, Freezer


2. Condenser, Freezer

M. Item A111409 - Rack Shelving System, Can,

2. Basis of Design Product: Eagle Group Model CRC4 System-2436


4. Wire Shelving Can Rack System, (4) 24"W x 36"L wire shelves, (4) 63"H posts, chrome finish with four 7-3/4”Wx27”dx11-1/2”H can rack mounts, NSF approved.



FOODSERVICE



11 4000-11

N. Item No. A111410 - Ice Maker, Flake-Style with Compatible Bin (for size indicated).

1. Hoshizaki Model F-1002MAJ

2. Ice Maker, Flake-Style, remote air-cooled, remote condenser (specified separately), maximum 980-lb. production/24 hours, stainless steel finish, "snow" style flaked ice, R-404A refrigerant, 208-230v/60/1.

3. Accessories:

a. 1 ea. 2-Year parts & labor on entire machine.

b. 1 ea. 5-Year parts on compressor & air-cooled condenser.

c. 1 ea. NOTE: 3 wire with neutral for 115V required.

d. 1 ea. Model BD-500SF Ice Bin, hinged bottom door & top view windows, approximately 500-lb. ice storage capacity, for top-mounted ice maker, stainless steel construction, universal top included, with die cast legs, protected w/HoshiGuard antimicrobial agent.

e. 1 ea. Universal top kit included.

f. 1 ea. 5-Year parts & labor for bin.

g. 1 ea. Model URC-6F Remote Condenser, R-404A refrigerant, 115v/60/1, for F-1001MRH(-C).

h. 1 ea. Model R404-3546-2 35' Pre-Charged Tubing Kit, R-404 refrigerant, for URC-6F.

i. 1 ea. Model 9320-22H Water Filter Assembly, HC-H Filter with HoshiGuard Antimicrobial Agent, Class 1 T & O, coarse filtration, for double

O. Item No. A111411 - Shelving Unit, Starter, Metal, Wire



3. Wire Shelving Starter Unit, (4) 24"W x 36"L wire shelves, (4) 74"H posts, green epoxy finish with antimicrobial protection, NSF approved.

P. Item No. A111412 - Rack, Dunnage

1. Basis of Design Product: Eagle Group Model DR-2460E

2. Available Manufacturers: Metro, New Age

3. Dunnage Rack, square bar, 1-tier, 24"W x 60"L x 8"H, weight capacity 2000 lbs., all welded aluminum construction, NSF

Q. Item No. A11413 - Rack, Pot & Pan (Fully Enclosed with Prison Package)

1. Basis of Design Product: New Age Model 1290PP





3. Pot & Pan Rack, mobile, 4 tier, 21"D x 28"L x 68"H, 1200 lb. capacity, aluminum construction, 5" stem casters (#C450), shipped knocked down, NSF certified

R. Item No. A111414 - Serving Counter, Hot Food, Electric

1. Piper Products/Servolift Eastern Model 2HFSL

2. Elite Serving Counter, Hot Food, Electric, 50"L x 19"D x 36"H, mobile modular design, slim line style, s/s open base w/under shelf, with two 12" x 20" hot food wells, s/s top & legs, w/5" casters, NSF, UL 240V/60/1ph

3. Accessories:

a. 1 ea. 1-Year warranty parts and labor from date of purchase.

b. 1 ea. 240V/60/1ph

c. 2 ea. Bottom accessible elements, per well.

d. 1 ea. Model DRN-32 Common drains & manifold for Elite Systems, for two openings - 32"W.

S. Item No. – Not Used

T. Item No. A111415 - Serving Counter, Cold Pan

1. Piper Products/Servolift Eastern Model 2-CMSL

2. Elite Cold Food Serving Counter, slim line style, 50"L x 19"W x 36"H, 2-pan size, 5" dp, mechanically cooled, mobile modular design w/interlocking mech., 14 ga. s/s top, s/s front, end panels, louvered panel, under shelf & Sliding doors, 5" casters, NSF, UL

3. Accessories:


b. 1 ea. 220/240V.

U. Item No. – Not Used

V. Item No. A111416 - Spare No.

W. Item No. A111417 - Dishtable, Accessory

1. Basis of Design Product: Eagle Group Model 606299


3. Rack Shelf, 60"L, tubular design, 1-5/8" dia. full length tubing, wall mounted, KD

X. Item No. A111418 - Waste Can (Owner Furnished / Owner Installed)

Y. Item No. A111419 - Dishtable, 'L' Shape

1. Basis of Design Product: Eagle Group Model SDTCR-72-14/3


3. Soiled Dishtable, corner design, 72" x 87", "L" shape, for right-to-left operation, 20"x20"x5"deep pre-rinse sink as located on drawing, scrap block, 14 gauge type 304 stainless steel top, stainless steel tubular legs, crossrails, gussets & feet. Provide (1) Scrap Basket, (1) Rack Slide and (1) Scrap Trough, 5"W x 2"D, 1-1/2" center drain opening, removable basket with handles, stainless steel construction.



FOODSERVICE



11 4000-13

Z. Item No. A111420 - Hose Reel with Spray

1. Basis of Design Product: Fisher Model 29661

2. Available Manufacturers: T & S Brass

3. Hose Reel Assembly, under counter reel rinse with utility spray valve, 12 feet of 3/8" ID hose that will withstand 140° F water temperature, hose has a 200 lb. working pressure rating, 3/8" inlets NPT female.

AA. Item No. A111421 - Pre-Rinse Faucet, Backsplash Mount



3. Pre-Rinse Assembly, splash-mounted mixing valve, 8" c/c, with spring action flexible gooseneck, with spray head (1.15 gallons per minute @ 60 PSI), with wall bracket.

AB. Item No. A111422 - Pant-leg condensate ducts (Two required)

1. Pant-leg condensate ducts - By Mechanical Sub-Contractor

AC. Item No. A111423 - Dishwasher, Conveyor Type

1. Basis of Design Product: Stero Model ER66S

2. Available Manufacturers: NO SUBSTITUTIONS

3. Dishwasher with Power Scrapper, conveyor type, high temp. water saver, two tank, 232 racks per/hour, tank heat to be specified, auto fill, shut-down timer, recirculated power wash, fresh water 180° final sanitizing power rinse, stainless steel front panel, tank & hood, (1) 1 HP, (1) 2 HP, NSF, UL 921,ENERGY STAR®. Right to Left operation 480v/60/3 ph. Mounted circuit breakers (voltage over 250v) Electric 10 kw heater (thermostatic control & low water cut-off). Furnish Top mounted inter-plumbed booster heater, 70 degree rise, 30 KW. Provide Cold water Aquastat for scrapper. Furnish (1) Table limit switch and (2) Vent cowls. Provide machine as a medium security prison package.

AD. Item No. A111424 – Not Used

AE. Item No. A111425 - Dishtable, Straight

1. Basis of Design Product: Eagle Group Model CDTL-84-14/3

2. Available Manufacturers: Universal Stainless, Tw\o Rivers Fabrication

3. Clean Dishtable, straight design, 24"L, for right-to-left operation, 14 gauge type 304 stainless steel top, stainless steel tubular legs, crossrails, gussets & feet. Provide 6’ full undershelf, 14/304 stainless steel.

AF. Item No. A111426 - Floor Trough

1. Specifier I.D. #M125

2. Basis of Design Product: Eagle Group Model FT-1272-FG





4. Floor Trough, 12" x 60", 14 gauge type 304 stainless steel all-welded construction, built-in pitch, secured with anchor straps, stainless steel waste cup with removable stainless steel basket, accommodates up to 4" dia. waste pipe, subway style fiberglass grating

AG. Item No. A111427 - Sink, Three (3) Compartment

1. Basis of Design Product: Eagle Group Model FN2060-3-36-14/3


3. Sink, Three Compartment, stainless steel, with 18" left & right-hand drainboards, 20" front-to-back x 20"W compartment, 14"D, with 13” H splash, stainless steel open frame base, boxed crossrails, 14/304 stainless steel. Provide stainless steel undershelf under drainboards, 36” L with short legs. Furnish holes for mounting hatco sink heater. Provide (1) Disposal provision package, includes weldment only for collar which is furnished by others, control panel bracket weldment, and holes for pre-rinse & anti-siphon vacuum breaker. Furnish stainless steel apron to cover sink bowls.

AG.1. Item A111427 (Sub Item No. 27.1) - Faucet, Backsplash Mount (2 REQUIRED)



4. Faucet, wall/backsplash mount, 8" c/c, 16" long swing spout, 1/2" inlets.

AG.2. Item A111427 (Sub Item No. 27.2) - Drain, Lever Handle (3 REQUIRED)



3. DrainKing Waste Valve, with flat strainer, 12 GPM drain rate, cast red brass body.

AG.3. Item A111427 (Sub Item No. 27.3) - Sink Heater, Electric (1 REQUIRED)

1. Hatco Model 3CS2-9B NO SUBSTITUTIONS

2. Hydro-Heater Sanitizing Sink Heater, Electric, undersink design, stainless steel front, powder coated body, low water cut-off, electronic temperature monitor, for 21"-25" square sink area, 9kw, 3-ph balanced. Includes 24/7 parts & service assistance. 208v/50/60/3-ph, 25 amps (balanced). Stainless steel body & base, all. Provide Security package (one way screws and control cover) and (1) Flush hose, cleaning brush, stopper and adapter.

AK. Item No. 28 - Sink, Hand, Wall Mount (2 REQUIRED)

1. Basis of Design Product: Eagle Group Model HSA-10-FA-PE

2. Available Manufacturers: No Substitutions

3. Hand Sink, pedestal mounted base, 14-3/4" x 18-7/8" with 7-1/2" backsplash, stainless steel construction, electronic eye gooseneck spout, P-trap, tail piece, basket drain deep-drawn seamless design-positive drain, NSF approved. Provide MicroGuard™ antimicrobial finish on bowl only. Furnish (1) Emergency Eye Wash Unit, faucet-mount, fits in place of aerator on spout, two dust covers, pull valve activates fountain, polished chrome finish (For installation on dish room sink.) (1) Anti-Scald Valve, for use with faucet-mount emergency eye wash unit, automatic shutdown with either hot or cold water failure, strainer, flow regulator. Provide (1) Temperature Adjustment Valve for each sink, for electronic handsinks only, built-in check valves, to mix hot and cold water. Furnish Side Mount Wall Brackets, one pair per sink, fits standard HSA models only.



FOODSERVICE



11 4000-15

AL. Item A111429 - Stand, Equipment

1. Basis of Design Product: Hobart Model CUTTER-TABLE3


3. Table Model 205025 with feet, 27" x 32", one shelf, for food cutters. Provide (1) Set of 4 casters (2 locking type).

AM. Item A111430 - Food Slicer

1. Basis of Design Product: Hobart Model 2712C+BUILDUP


3. Slicer, Correctional, semi-automatic, angle feed, 12" stainless steel CleanCut knife, MICROBAN Poly-V- belt, permanent ring guard, 2-speed tilt remove auto stainless steel carriage, stainless steel knife cover, lock controls, top mounted sharpener without stone, aluminum base with tilt, tamper resistant.

4. 1-Year parts, labor & travel time during normal working hours w/in the USA. 120/60/1 with lockable controls. Furnish correctional sharpener kit.

AN. Item A111431 - Food Processor, Electric

1. Basis of Design Product: Mannhart, Inc Model M2000-3


3. Vegetable Cutter, continuous gravity feed, 600-650 lbs/hr slicing & 650-800 lbs/hr dicing capacity, removable hinged feed hopper lid with magnetic safety lock, dual feed openings with safety pusher, wiper blade ejection system, HD motor with poly-v-belt, polished cast aluminum & s/s housing, includes training CD. 1/2 HP, 115v/60/1, 8.5 amps, made in USA, NSF, UL listed. One year parts & labor warranty (cutting edges & dicing grids not included). Furnish (1) Accessory Package, includes SLICER-S2, SLICER-S3, SLICER-S11, SHRED-SH3, DICE-D11, SLICER-J6X6; for M2000 & M3000 vegetable cutters, made in USA, NSF.

AO. Item A111432 Work Table, 96" Long

1. Basis of Design Product: Eagle Group Model T3096SE-BS


3. Work Table, 30"W x 96"L, 14 gauge type 304 stainless steel top with 4-1/2" backsplash, rolled front edge, sq. turndown ends, 18 gauge stainless steel undershelf, 1-5/8" O.D. 16 gauge stainless steel legs adjustable stainless steel feet. Provide drawer assembly, 3 tier, stainless steel cabinet, roller track, 22 1/2" X 24" X 22" deep , guides, roller slides, removable stainless steel pan, no legs, NSF. Furnish (2) sink, 20" x 20" x 14" bowls, for 30"W tables, complete with basket drain as located on FS drawing.

4. Provide apron in front of sink or cutout, 16 gauge stainless steel. All welded construction, legs, undershelf, sink bowls and top. Furnish (2) Lever Waste Standard Valve, 3-1/2" industry standard sink opening, 1-1/2" drain outlet, flat strainer, stainless steel. Provide (1) Faucet, deck-mounted, 8" centers, 10" swing spout, lever handles, 3/4" inlets.

AP. Item A111433 – Spare No.




AQ. Item A111434 - Shelf, Wall Mount

1. Basis of Design Product: Eagle Group Model 600WS1272HD


3. Shelf, Wall-Mounted, 14 gauge 304 stainless steel, 12"W x 6 feet long.

AR. Item A111435 - Spare No.

AS. Item A111436 - Disposer

1. Basis of Design Product: InSinkErator Model SS-300-15C-AS101

2. Available Manufacturers: Salvajor

3. Complete Disposer Package, with 15" diameter bowl, 6 5/8" diameter inlet, with removable splash baffle, 3 HP motor, stainless steel construction, includes 2 syphon breakers, 2 solenoid valves, 2 flow control valves, programmable AS101 control panel, automatic water saving function, auto reversing, timed run, post flush. 1 yr. parts & labor warranty from date of installation. Provide short disposer body height, 3-1/2" shorter than std. -27, 460v/60 /3-ph, 2.5 amps. Furnish offset chute, mounts between disposer and sink bowl. Provide (1) 15" sink bowl cover and (1) Cast iron waste outlet flange. Provide (3) flanged feet for floor mounting. Provide (1) tamper proof screw kit, for securing InSinkErator control panels, includes 4 screws, opening tool.

AT. Item A111437 - Disposer

1. Basis of Design Product: InSinkErator Model SS-300-7-AS101

2. Available Manufacturers: Salvajor

3. Complete Disposer Package, sink mount system, 6 5/8" diameter inlet, with #7 collar adaptor for sink installation, 3 HP motor, stainless steel construction, includes 2 syphon breakers, 2 solenoid valves, 2 flow control valves, removable splash baffle, stainless steel sink stopper, programmable AS101 control panel, automatic water saving function, auto reversing, timed run, post flush.1 yr. parts & labor warranty from date of installation. Furnish short disposer body height, 3-1/2" shorter than std. -27, 460v/60 /3-ph, 2.5 amps. Furnish (3) flanged feet for floor mounting. Provide (1) Cast iron waste outlet flange, (1) disposer throat guard, 6-5/8" opening only, requires 11292A and (1) tamper proof screw kit, for securing InSinkErator control panels, includes 4 screws, opening tool.

AU. Item A111438 - Shelving Unit on Dolly Truck

1. Basis of Design Product: Nexel Model D2436PS

2. Dolly Truck, 4 wire shelves, 24"W, 36"L, 63" posts, 5" polyurethane wheel plate casters (2 swivel, 2 rigid) 1200-lb. capacity, dolly base is steel w/chrome finish, corner rubber bumpers, stainless steel.

AV. Item A111439 - Conveyor, Tray Make-Up

1. Basis of Design Product: Piper Products/Servolift Eastern Model SSC-12

2. Conveyor, Tray Make-Up, 12"L, non-powered skate-wheel conveyor, nylon rollers, stainless steel roller frames, designed for gravity operation, stainless steel construction.



FOODSERVICE



11 4000-17

3. Accessories:


b. 1 ea. 12" Raceway

c. 4 ea. 240V/60/1 outlet, specify amp draw, price per outlet

d. 1 ea. Cord & plug, 100 amp max.

e. 12 ea. Rollers removable in sections, per linear foot.

f. 6 ea. Casters in lieu of legs (6 required) priced per ea.

AW. Item A111440 – Cabinet, Meal Tray Delivery

1. Basis of Design Product: Piper Products/Servolift Eastern Model TQM2-L28-1418

2. Tray Delivery Cart w/Doors, low-profile double compartment, for 14” x 18” trays, capacity 28 trays, stainless steel construction, (6) 6” casters (4 swivel with brakes, 2 fixed, mounted in center).

3. Accessories:

a. 2 ea. NOTE: Tray sizes vary by manufacturer to insure a proper fit, a tray sample or actual tray dimensions must be provided.

b. 2 ea. NOTE: All dimensions are approximate; please contact factory for actual dimensions.

c. 2 ea. Stainless steel top rail

d. 2 ea. Top mounted transport latches (one per door)

AX. Item A11141 - Reach-In Refrigerator

1. Basis of Design Product: NOR-LAKE, Inc. AdvantEDGE Model NLR49-S

2. Two-door reach in refrigerator.

a. Exterior Finish: Stainless steel exterior front, sides and doors. Top, bottom and back are galvanized.

b. Interior Finish: Liner and door stainless steel.

c. Insulation: Complete cabinet and door, foamed-in-place polyurethane.

d. Hardware: Heavy duty, pivot hinges; key locks, curved handle with recessed pocket, self-adjusting magnetic gasket, (4) 4” dia. Casters, (4) vinyl coated shelves per door.

e. Instrumentation: Microprocessor with digital display for temp adjustment.

f. Refrigeration: Complete bottom mounted refrigeration system with copper tube, ceiling mounted aluminum fin evaporator. Condensate collected and automatically evaporated forma n energy efficient air over wick style vaporizer. Recessed drain lien in cabinet back. Refrigerant flow controlled by capillary tube. R-134a refrigerant. Operating temps +34oF to +38oF.

g. Approvals: UL, C-UL, ETL Sanitation and Energy Star listed.




AY. Item A111442 -Kettle, Electric, Table Top

1. Basis of Design Product: Vulcan Hart Model K12ETT NO SUBSTITUTIONS

2. Tilting Kettle, Electric, 12-gallon capacity, 2/3 jacketed counter top model, 316 stainless steel liner with embossed gallon/liter markings, heavy bar rim, stainless steel splash proof console on right with faucet bracket, cleaning lock, 50 psi, 12.0kW. 1 year limited parts & labor warranty. 480v/60/3. Provide (1) Stand, 29-1/2" wide, for Electric Counter Kettles, stainless steel frame & flanged feet, 1-1/2" NPT drain outlet, includes sliding drain pan.

BA. Item A111443 - Tilting Skillet/Braising Pan, Electric

1. Basis of Design Product: Vulcan Hart Model VE40 NO SUBSTITUTIONS

2. Braising Pan, electric, 40-gallon capacity, 46" wide open base, manual tilt, 9" deep stainless steel pan with gallon markings, pouring lip & removable strainer, spring assist cover with drip edge, pan holder, water tight solid state controls, includes L faucet bracket, 12" stainless steel legs with adjustable flanged feet, 12kw 480v/60/3ph, 16 kw, 23 amps. 1 year limited parts & labor warranty, standard. Provide motor driven pan lift, 2" draw-off valve left, straight, with strainer and (1) double pantry deck mount faucet, with 12" riser & 12" swivel spout. Enclosed box faucet bracket, add 3". Furnish catch can with bail handle & drain hose for DOV.

BB. Item A111444 - Floor Trough

1. Basis of Design Product: Eagle Group Model FT-2436-SG


3. Floor Trough, 24" x 36", anti-splash, 14 gauge type 304 stainless steel all-welded construction, built-in pitch, secured with anchor straps, stainless steel waste cup with removable stainless steel basket, accommodates up to 4" diameter waste pipe, subway style fiberglass grating.

BC. Item A111445 - Griddle, Counter Unit, Gas

1. Basis of Design Product: Montague Company Model DG2472-SAT

2. Available Manufactures: No substitutions.

3. Legend 72" Heavy-Duty Griddle, gas, 1" thick ground & polished steel plate, 24" deep grill area, (6) snap action thermostatic controls, safety pilot ignition, 3/4" NPT rear manifold with pressure regulator, s/s front, 4" adjustable s/s legs, 180,000 BTU, One year parts and labor warranty, std. Natural gas. Provide Solid State Thermostat in lieu of std. snap action T-stat. Furnish three automatic pilot re-lights. Provide equipment stand, stainless steel with lower shelf. 34-1/2" working height and casters with 5" wheel 6" OA (set of 6). Furnish (1) 48” - ¾” flexible quick disconnect gas hose and restraining device.

BD. Item A111446 - Fryer Battery, Gas

1. Basis of Design Product: Pitco Frialator Model 2-SSH55RSSTCS/FD

2. Available Manufactures: No substitutions

3. Solstice Supreme High Efficiency Fryers, gas, (2) 40-50lb oil capacity full tanks, solid state thermostats, boil out & melt cycle, drain valve interlock, matchless ignition, self-clean burner, downdraft protection, drawer filtration, stainless steel tank, front & sides, total 200,000 BTU, ENERGY STAR® Natural gas.



FOODSERVICE



11 4000-19

4. Provide casters, set of 4, for fryer battery, gas connector hose, 3/4" connection, for castered equipment, 48" long, with quick disconnect couplings, restraining device & thermal shut-off. Provide (1) pack Filter Paper, envelope, heavy duty, 18-1/2" x 20-1/2", (1) Clean Out Rod, for cleaning fryer drain line and (1)Fryer Cleaning Brush, high temperature, Teflon.

BE. Item A111447 - Convection Oven, Gas (Owner Furnished Contractor Installed – OFCI) per Addenda#2 VE Coordination Documents

1. Basis of Design Product: Blodgett Oven Model DFG100XCEL DOUBLE

2. Available Manufactures: No substitutions

3. Xcel Convection Oven, gas, double-deck, standard depth, solid state manual controls, 2-speed fan, EZ slide rack with (4) racks & (11) positions, porcelain crumb tray, halogen interior lights, simultaneous operated doors with glass, stainless steel front, sides & top, 6" stainless steel legs, flue connector, 80,000 BTU each. (2) Two year parts, (1) one year labor and (5) five year door parts warranty. Natural gas, (2) 115v/60/1-ph, 10.0 amps, 3/4 hp, cord & plug. Provide (1) Draft diverter (1) S/S interior liner (per deck) and (1) Solid stainless steel back (per deck). Furnish 4-1/4" low profile casters (set) in lieu of legs.

4. Provide (1) Gas manifold for double ovens, and (1) (2) 48" flexible gas hose w/quick disconnect & restraining device.

BF. Item A111448- Exhaust Hood w/Fire Suppression

1. See Division 23, Section “Commercial Kitchen Hood’ for ventilation hood requirements. Provided and Installed by Mechanical Contractor. (per Addenda #2 VE Coordination Documents)

2. Furnish and set in place per Division 23 specifications, using most stringent condition, or as follows: Delete item # BE.2 in its entirety per Addenda #2 VE Coordination documents.

a. Engineered Exhaust Hood w/ Fire Suppression and integral Capture-jet fan technology.

b. Two Sections, #48L @ 132”L x 54”D x 24”H, with 12”L fire cabinet. #48R @ 145”L x 54”D x 24”H, both 18 gauge, type 304 stainless steel where exposed and unexposed surfaces. #48L-2226 CFM Exhaust @ 0.431”. #48R-1664 CFM Exhaust @ 0.509”

c. Supply Plenum, Two Sections, #48L @ 145” L x 24”D. #48R @ 145” L x 24”D. #48L-1631 CFM Supply @ 0.197 S.P. #48R-1631 CFM Supply @ 0.197 S.P.

d. Filter Removal Tool

e. Incandescent Lighting.

f. Fire Cabinet with switches for fans and lights in #29L.

g. Stainless steel closure panels to ceiling.

h. Ansul R102 pre-engineered wet chemical system per UL300. Pre-piped to include exhaust duct and plenum with stainless steel drops, remote pull station. Microswitches and cartridge.

i. Final field installation by Certified Technician.




j. T.A.B. (Test Air Balance) Ports; KSA S/S Filters 93-98% Efficient on Particulate in the 5-10 Micron Range Based on ASTM-F2519-05; Exhaust Volume Based on ASTM-f1704-05 and F2474-05

k. Standard stainless steel backsplash to extend entire distance between walls. Splicing strips as required. Stainless steel enclosure to finished ceiling (verify ceiling height).

l. Provide shunt-trip to mechanical contractor. Schedule inspection and testing by qualified Ansul representative.

BG. Item A111449 - Cart, Dish

1. Basis of Design Product: Piper Products/Servolift Eastern Model 339-3487

2. Disch Cart, double, shelf size 27-1/4" x 34", NSF, stainless steel construction

3. Accessories:


b. 1ea. Model 341-3479 Dust cover, plastic, use with Model 339-3487, double dish cart

c. 1 ea. Model-R Rotating bumpers.

BH. Item A111450 -Oven, Microwave

1. Basis of Design Product: Amana Commercial Products Model HDC21

2. Available Products: No Substitutions

3. C-Max Microwave Oven, 2100 watts, compact, stackable, stainless steel interior & exterior, X2 quantity pad, 11 power levels, 100 memory settings, auto voltage sensor, side hinged door, full 3 year warranty, 20 amp, 208-240V, 60Hz, NEMA 6-20.

BI. Item A111451 - Pot Rack, Ceiling Mount

1. Basis of Design Product: Advance Tabco SC-72


3. Pot Rack, Ceiling Hung, triple bar design with ceiling hangers, 72"L, with stainless steel two-prong sliding hooks, constructed of 3/16" x 2" stainless steel, NSF.

BJ. Item A111452 - Table, Work

1. Basis of Design Product: Eagle Group Model T3072SE


3. Work Table, 30"W x 72"L, 14 gauge type 304 stainless steel top with box Marine edges all sides, 18 gauge stainless steel undershelf, 1-5/8" O.D. 16 gauge stainless steel legs, adjustable stainless steel feet, NSF. Provide left hand mounted microwave shelf 24” X 24” as shown on FS drawing. Include Item #52.1 Sink, Drop-In Eagle Group Model CDI-22-22-13.5-1. Sink Bowl, Drop In, 1 compartment, 22"W x 22" front-to-back x 13-1/2"D, 18 gauge stainless steel construction, with goose neck faucet located as shown on FS drawing. Provide (1) set of stainless steel flanged feet.

BK. Item A111453 - Spare No.



FOODSERVICE



11 4000-21

BL. Item A11454 - RETHERM OVEN

1. Basis of Design Product: Food Warming Equip Model RH-RB-26


3. Rethermalizer/Holding for Roll-In Rack, electric, dual-cycle, (2) dutch doors, standard controls with max. 350° F range, capacity (1) RRB-26 (sold separately) holds 26 wire baskets, stainless steel construction, 6" legs.

BM. Item A111455 - Cart, Tray Transport, Enclosed

1. Basis of Design Product: Food Warming Equip Model PTS-0609-1015-56HA


BN. Item A11456 - Food Mixer

1. Basis of Design Product: Hobart Model HL400-8STDDEL


3. Legacy Planetary Mixer, 1.5 hp, 200-240/50/60/1, 40-qt., 3 fixed speeds, gear-driven transmission, program recipe timer, #12 taper attach hub, manual bowl lift, bowl guard, SS Bowl, "B" beater, "D" whip, "ED" dough hook, scraper, truck, ingredient chute.

BO. Item A11457 - Table, Work

1. Basis of Design Product: Eagle Group Model T3072SE-BS


3. Work Table, 36"W x 84"L, 16 gauge type 430 stainless steel top with 4-1/2" backsplash, rolled front edge, sq. turndown ends, 16 gauge stainless steel 1-5/8" O.D. & 1-1/4" O.D. side & rear crossrails, legs, stainless steel bullet feet.

BP. Item A11458 - Bin, Ingredient

1. Basis of Design Product: Cambro Model IBS27-148

2. Available Manufacturers: EQUAL

3. Ingredient Bin, mobile, 27 gallon capacity, 1-pc seamless polyethylene bin, 2-pc sliding polycarbonate lid, S-hook on front (scoop NOT included), (4) 3" heavy duty casters (2 front swivel, 2 fixed), white with clear cover. Provide (1) Scoop per bin.

BQ. Item A111459 - Spare No.

BR. Item A111460 - Sink, Scullery, 1 Compartment

1. Basis of Design Product: Eagle Group Model FN2016-1-14/3


3. Sink, One Compartment, stainless steel, 20" front-to-back x 16"W compartment, 14"D, with 9 1/2"H splash, stainless steel open frame base, boxed crossrails, 14/304 stainless steel.




BS. Item A111461 - Cart, Utility

1. Basis of Design Product: Lakeside Manufacturing Model 615

2. Available Manufacturers: EQUAL

3. Bussing Cart, enclosed back and sides, 4 shelf, shelf size 15-1/2" x 24", stainless steel angle frame with push handle, 300 lb. capacity.

BT. Item A111462 - Floor Trough

1. Basis of Design Product: IMC/Teddy Model CFT-1236-PFG

2. CFT Floor Trough, 12" wide x 36" long x 4" deep, with drain & (PFG) pultruded fiberglass grating, grey Provide flashing frame/clamping ring, for waterproof membrane, for 12" width trough (includes screws, price per foot) and Beehive strainer, each.

PART 3 - EXECUTION

3.1 INSTALLATION

A. Install foodservice equipment level and plumb, according to manufacturer's written instructions.

B. Connection of equipment to utilities shall be performed by the trades. Coordinate and answer questions pertinent to the proper connection.

C. Provide cutouts in equipment, neatly formed, where required to run service lines through equipment to make final connections.

1. Complete equipment assembly where field assembly is required.

a. Provide closed butt and contact joints that do not require filler.

1) Grind field welds on stainless-steel equipment smooth, and polish to match adjacent finish.

(a) Install equipment with access and maintenance clearances that comply with manufacturer's written installation instructions and requirements of authorities having jurisdiction.

(b) Install closure-trim strips and similar items requiring fasteners in a bed of sealant.

(c) Install joint sealant in joints between equipment and abutting surfaces with continuous joint backing, unless otherwise indicated. Produce airtight, watertight, vermin-proof, sanitary joints.

3.2 CLEANING AND PROTECTING

A. After completing installation of equipment, repair damaged finishes.

B. Clean and adjust equipment as required to produce ready-for-use condition.

C. Protect equipment from damage during remainder of the construction period.



FOODSERVICE



11 4000-23

3.3 DEMONSTRATION

A. Engage a factory-authorized service representative to train Owner's maintenance and kitchen personnel to adjust, operate, and maintain foodservice equipment. Refer to Division 01 Section "Closeout Procedures & Demonstration and Training."

END OF SECTION

ROOF LEGEND

PLAN MARK DESCRIPTION REFERENCE

1/4"

FT.TAPERED INSULATION N/A

STRUCTURAL STRUCTURAL SLOPE N/A

DESIGNATES ROOF TYPE, SEE ROOF NOTES.X N/A

KEYNOTES N/A?

1

A1.0

DESIGNATES DETAIL MARKSEE DETAIL 1 ON

SHEET A1.0

N/A

LADDER

PARAPET WALL REFER TO ROOF PLAN

PRIMARY ROOF DRAIN & SECONDARY OVERFLOW ROOF DRAIN W/ SUMP

DETAIL 2A SHEET A521DETAIL 2D SHEET A521

OD

DS CONDUCTOR HEAD AND DOWNSPOUTDETAILS 2A & 2G SHEET A520

SPLASH BLOCK DETAIL 2G SHEET A520

VTR VENT THROUGH ROOF DETAIL 2F SHEET A520

LIGHT MONITORS DETAIL 6C SHEET A520

EXHAUST FAN DETAIL 2D SHEET A520

GRAVITY FLOW ROOF VENT DETAIL 2D SHEET A520

ROOF TOP UNIT DETAIL 2D SHEET A520RTU

OS OVERFLOW SCUPPERDETAILS 4A & 4B SHEET A520

DETAIL C6 SHEET A504

DOOR THRESHOLD DETAIL 4E SHEET A520

SP SUPPORT POST DETAIL 2F SHEET A520

C CONDUIT PENETRATION DETAIL 2F SHEET A520

RAIL MOUNTED UNIT DETAIL 5F SHEET A520

DUCT PENETRATION DETAIL 2D SHEET A520

L.5

STRUCTURAL

STRUCTURAL

STRUCTURAL

STRUCTURAL

ST

RU

CT

UR

AL

ST

RU

CT

UR

AL

1/4

"

FT

1/4

"

FT

1/4

"

FT

1/4

"

FT

1/2

"FT

1/2

"FT

1/2

"FT

1/2

"FT

1/2

"FT

1/2

"FT

1/2

"FT

1/4

"

FT

1/4

"

FT

1/4"

FT

ST

RU

CT

UR

AL

1/2"FT

1/2"

FT

1/2"

FT

1/2"FT

DS DS

DS

A

B.2

D

C

E

F.1

G

H

I

A B C

D

F G J

2

3

4

7

9

10

E

M

6

5

2.2

N

2.6

2x

1x

H L

1y

1

E.7 F.5

2y

8

K

5.3

A.5 B.5

9.2

11

1.9

3D

A513

3D

A513

3D

A513

1/4"

FT

1/4"

FT

K

1/2

"FT

1/2

"FT

1/2"

FT

1/2"FT

1/2

"FT

6D

A513

Sim

4F

A520

2zE.9 K.8

F.2F

1/4

"

FT

1/4

"

FT

1/4

"

FT

1/2

"

FT

1/2

"FT

1/2

"FT

1/2

"FT

1/2

"FT

6A

A520

SIM

6F

A513

Sim

6D

A513

Sim

1/2

"FT

1/2

"

FT

1/2

"FT

4C

A520

3D

A513

1/4

"

FT

1/4

"

FT

4C

A520

B.1

1/2

"FT

1/2

"FT

1/4

"

FT

1/4

"

FT

RTU

5E

A520

5E

A520

4C

A520

1/4

"

FT

1/4

"

FT

6B

A509

Sim

6C

A520

6C

A520

S

S

6E

A520

Sim

6E

A520

Sim

6E

A520

Sim

6E

A520

Sim

A07.15TYP.

A07.15

TYP.

TYP.

DS DS

TYP.

A07.16A07.16

TYP.

A07.16A07.16

TYP.

A07.16A07.16

TYP.

A07.16A07.16

TYP.

A07.15

TYP.

A07.17

TYP.

A07.16A07.16

TYP.

SPSP

MAINTENANCE BUILDING IS UNDER A SEPARATE CONTRACT AND SHALL NOT BE INCLUDED IN THE BASE BID

A07.32

A07.17

RTU

1/2"

FT

1/2"FT

1/2

"FT

A07.15

TYP.

A07.15TYP.

10'-0"

A516

2G

A516

2G

SOUTH CANOPY IS PART OF BASE BID. ALTERNATE #5 IS WITHOUT SOUTH CANOPY

A07.15

TYP.

MECHANICAL UNITS ON ROOF AREA "H" SHALL BE INSTALLED ON RAIL CURBS RUNNINGEAST AND WEST. REFER TO DETAIL 5F SHEET A520.

A13.05

A13.07

4C

A520

6G

A520

K.1

1/2"

FT

1/2

"FT

1/2"

FT

1/2

"FT

1/2"

FT

1/2

"FT

1/2"

FT

1/2

"FT

1/2

"FT

1/2"

FT

1/2"

FT

1/2

"FT

1/4

"

FT

1/4

"

FT

AD2VE

AD2VE

AD2VE

AD2VE

AD2VE

AD2VE

AD2VE

ROOF PLAN GENERAL NOTES:

A. ROOF PLAN LAYOUT, LOCATION, AND SECTIONS WERE TAKEN FROM EXISTING BUILDING PLANS AND FIELD CONDITIONS. THE CONTRACTOR SHALL VERIFY ALL CONDITIONS.

B. THE EXACT LOCATION AND ELEVATION OF ALL PUBLIC UTILITIES MUST BE DETERMINED BY THE CONTRACTOR. IT SHALL BE THE RESPONSIBILITY OF THE CONTRACTOR TO ASCERTAIN WHETHER ANY ADDITIONAL UTILITIES OTHER THAN THOSE SHOWN ON THE PLANS MAY BE PRESENT.

C. REMOVE EXISTING ROOF SYSTEMS DOWN TO THE EXISTING DECKS.D. REMOVE EXISTING SHEET METAL, UNLESS NOTED OTHERWISE, AND REPLACE

WITH NEW AS PLANS SHOW. ALL PERIMETER WOOD BLOCKING SHALL BE OF UNIFORM HEIGHT AND OF A MINIMUM HEIGHT TO MATCH THE THICKNESS OF THE NEW INSULATION SYSTEM. THE CONTRACTOR SHALL VERIFY HEIGHT OF ALL WOOD BLOCKING.

E. THE CONTRACTOR SHALL FIELD VERIFY ALL DIMENSIONS OF BUILDING AND DRAIN LOCATIONS BEFORE ORDERING TAPERED INSULATION MATERIALS. SUBMIT TAPERED INSULATION LAYOUT PLAN. SEE SPECIFICATION SECTION 07 22 00 FOR SYSTEM DESCRIPTION.

F. ALL EXISTING METAL HOODS, VENTS, CAPS, ETC., REMOVED AND REINSTALLED DURING CONSTRUCTION SHALL BE PROPERLY REFASTENED TO PROVIDE WATERTIGHT CONDITIONS.

G. RAISE ALL CURBS AND VENTS WHICH DO NOT MEET THE 8" MINIMUM FLASHING HEIGHT REQUIREMENT.

H. FLASH ALL SCUPPERS, CURBS, VENTS AND STACKS AS SHOWN IN PLAN. REFER TO MANUFACTURER'S STANDARD DETAILS AND RECOMMENDATIONS FOR ANY MISCELLANEOUS DETAILS NOT SHOWN IN THE PLANS.

I. USE OF MANUFACTURER-APPROVED PENETRATION POCKET WILL NOT BE PERMITTED UNLESS APPROVAL IS OBTAINED IN WRITING FROM SHIVE-HATTERY, INC. PRIOR TO INSTALLATION.

J. PROVIDE DISCONNECT AND RECONNECT OF MECHANICAL AND ELECTRICAL EQUIPMENT AS REQUIRED TO ACCOMMODATE INSTALLATION OF NEW ROOF SYSTEM AND INCREASE IN HEIGHT OF CURB. VERIFY EQUIPMENT IS OPERATIONAL WHEN WORK IS COMPLETE. COORDINATE THIS WORK WITH THE OWNER.

K. CONTRACTOR SHALL BE RESPONSIBLE FOR MAINTAINING WATER TIGHT CONDITIONS AT ALL TIMES DURING CONSTRUCTION.

L. CONTRACTOR SHALL BE RESPONSIBLE FOR THE PROTECTION OF THE ROOF SYSTEM ON THE BUILDING. A MINIMUM LAYER OF 1.5" INSULATION WITH A LAYER OF 1/2" PLYWOOD SHALL BE LAID OVER THE ROOF SYSTEM IN A CONTINUOUS FASHION AS WORK PROGRESSES AROUND THE BUILDING. ANY DAMAGE TO THE ROOF SYSTEM WILL BE THE CONTRACTORS RESPONSIBILITY TO REPAIR.

M. CONTRACTOR SHALL BE RESPONSIBLE FOR THE PROTECTION AND REPAIR OF ANY DAMAGE CAUSED DURING CONSTRUCTION TO THE SURROUNDING GROUNDS. (GRASS, CONCRETE, ETC.)

N. CONTRACTOR SHALL BE RESPONSIBLE FOR THE RAISING/LOWERING OF EXISTING ROOF DRAINS TO FACILITATE THE INSTALLATION OF NEW INSULATION SYSTEM.

O. REPLACE ANY DAMAGED BROKEN OR MISSING DRAIN GRATES, CLAMPING RINGS AND BOLTS WITH NEW. NEW DRAIN PARTS SHALL MATCH EXISTING DRAIN DESIGN. NEW DRAIN GRATES SHALL BE METAL. EXISTING PLASTIC DRAIN GRATES SHALL BE REPLACED WITH METAL DRAIN GRATES. ALL DRAINS SHALL BE TESTED AND MADE OPERATIONAL PRIOR TO COMPLETION OF PROJECT.

P. KEYNOTE LIST IS SPECIFIC TO THIS SHEET.Q. COORDINATE ROOF MOUNTED CAMERAS WITH SECURITY PACKAGE.

ROOF TYPES:

BASE BID:

ROOF LEVEL A & G60 MIL EPDM FULLY ADHERED .5" COVER BOARD2.5" POLYISOCYANURATE INSULATION 2.0" POLYISOCYANURATE INSULATIONVAPOR BARRIERMETAL DECK

ROOF LEVELS D & I60 MIL EPDM FULLY ADHERED.5" COVER BOARDTAPERED POLYISOCYANURATE INSULATION 1/4" SLOPE, 1.5" STARTVAPOR BARRIERMETAL DECK

ROOF LEVELS B, B.2, C, E, F, & H60 MIL EPDM FULLY ADHERED.5" COVER BOARDTAPERED POLYISOCYANURATE INSULATION 1/4" SLOPE, 2.5" STARTVAPOR BARRIERMETAL DECK

ROOF LEVELS J & B.160 MIL EPDM FULLY ADHERED.5" COVER BOARDTAPERED POLYISOCYANURATE INSULATION 1/4" SLOPE, 3.5" STARTVAPOR BARRIERMETAL DECK

ROOF LEVEL F.260 MIL EPDM FULLY ADHERED.5" COVER BOARDTAPERED POLYISOCYANURATE INSULATION 1/4" SLOPE, 4" STARTVAPOR BARRIERMETAL DECK

ROOF LEVEL K & K.160 MIL EPDM FULLY ADHERED.5" COVER BOARDTAPERED POLYISOCYANURATE INSULATION 1/4" SLOPE, 4.5" STARTVAPOR BARRIERMETAL DECK

ROOF LEVEL F.160 MIL EPDM FULLY ADHERED.5" COVER BOARDTAPERED POLYISOCYANURATE INSULATION 1/4" SLOPE, 3.5" STARTCONCRETE DECK

ALTERNATE BID:

ROOF LEVEL L60 MIL EPDM FULLY ADHERED.5" COVER BOARDTAPERED POLYISOCYANURATE INSULATION 1/4" SLOPE, 2.5" STARTVAPOR BARRIERMETAL DECK

4125 W

esto

wn P

kw

y, S

uite 1

00 | W

est D

es M

oin

es, Io

wa 50266

515.2

23.8

104 | fax 5

15.2

23.6

022 | w

ww

.shiv

e-h

attery

.com

6

5

4

3

BA D E

1

FC G

2

Iow

a | Illi

nois

| India

na

DR

AW

N:

AP

PR

OV

ED

:

ISS

UE

D F

OR

:

DA

TE

:

FIE

LD

BO

OK

:

PR

OJE

CT

NO

:

H

BA D E FC G H

6

5

4

3

1

2

Printe

d:

CLIN

TO

N C

OU

NT

Y J

US

TIC

E C

EN

TE

R

VE

CO

OR

DIN

AT

ION

SE

T

612

N 2

ND

ST

| C

LIN

TO

N, IA

527

32

A101

RO

OF

PLA

N

FO

R C

ON

ST

RU

CT

ION

41

63

15

0

MS

L

Au

thor

20

17

-07

-14

KEYNOTE LEGEND

KEY NOTE

A07.15 ALL TAPERED INSULATION USED TO CREATE ADEQUATEDRAINAGE BEHIND MECHANICAL UNITS AND FORCRICKETS/SADDLES SHALL BE SLOPED AT 1/2"/FT AND SET INA LAYER OF FOAM ADHESIVE.

A07.16 CONTRACTOR SHALL BE RESPONSIBLE FOR THEPROTECTION OF THE ROOF SYSTEM ON THE BUILDING. AMINIMUM LAYER OF 1 1/2" INSULATION WITH A LAYER OF 1/2"PLYWOOD SHALL BE LAID OVER THE ROOF SYSTEM IN ACONTINUOUS FASHION AS WORK PROGRESSES AROUNDTHE BUILDING. ANY DAMAGE TO THE ROOF SYSTEM WILL BETHE CONTRACTORS RESPONSIBILITY TO REPAIR.

A07.17 CONTRACTOR TO FURNISH AND INSTALL MANUFACTURERAPPROVED WALKWAY PADS IN INDICATED LOCATIONS,CONTRACTOR SHALL CUT A 6" WIDE SECTION OUT OF THEWALKWAY PADS IN VALLEY LINES OF CRICKETS/SADDLES.

A07.32 3.5" OF POLYISOCYANURATE INSULATION SHALL BEINSTALLED IN THE INDICATED AREA OVER THE METAL DECKPORTION OF ROOF AREA C. THE SPECIFIED ROOF SYSTEMSHALL THEN BE INSTALLED ON TOP. THE INSULATION OVERTHE CONCRETE DECK PORTION OF ROOF AREA C SHALL BESET IN A LAYER OF FOAM ADHESIVE SIMILAR TO ROOF AREAF.1. REFER TO DETAIL 6F SHEET A520 FOR A SIMILAR VAPORBARRIER TO ROOF MEMBRANE TIE IN DETAIL AT THE DECKTRANSITION.

A13.05 OWNER PROVIDED, OWNER INSTALLED RADIO ANTENNA.CONTRACTOR TO PROVIDE ALL NEEDED ROUGH IN TOPREPARE FOR OWNER INSTALLATION.

A13.07 OWNER PROVIDED OWNER INSTALLED COMMUNICATIONSARRAY / DISH. CONTRACTOR TO PROVIDE ALL NEEDEDROUGH-IN.

TRUE NORTH

NORTHPLAN

3/32" = 1'-0"6AROOF PLAN

VE

AD

20

8-0

3-2

01

7R

evis

ion

6

OSOSOSOS

S S

VOCATIONAL

OFFICE /

MEDICAL

SCREENING

1020

TOILET

1037

TOILET

1039

PUBLIC

VISITATION

1021B

PUBLIC

VISITATION

1022B

PUBLIC

VISITATION

1023B

PUBLIC

VISITATION

1024B

INMATE

VISITATION

1021A

INMATE

VISITATION

1022A

INMATE

VISITATION

1023A

INMATE

VISITATION

1024A

JAIL DEPUTY

WORK AREA

1025

JAIL ADMIN

OFFICE

1029

STAFF

TOILET

1036

DRESS IN /

OUT

1069

DRESS IN /

OUT

1071

SECURITY

ELECTRONICS

1068

PADDED

HOLDING

CELL

1051

HOLDING

CELL

1050

VEHICLE

EVIDENCE

1065

STAFF

VESTIBULE /

EVIDENCE

RELEASE

1074B

SPV

1074A

CORRIDOR

1073STAFF

DINING

1080

STORAGE

1070

EVIDENCE

PROCESSING

/ STORAGE

1064

VIDEO

COURT

1067

WEAPONS /

DRUGS

1066

HOLDING

CELL

1057

HOLDING

CELL

1056

HOLDING

CELL

1055

GROUP

HOLDING

CELL

1054

GROUP

HOLDING

CELL

1049

S.P.V. / O.W.I.

1052

VEHICLE

SALLYPORT

1053

EVIDENCE

DROP OFF

1063

SPV

1026

WOMEN'S

LOCKER

1027

BREAK

ROOM

1035

MEN'S

LOCKER

1028

STORAGE

1032

SPV

1031

VESTIBULE

1034

MECHANICAL

1040

JC/STORAGE

1061

HOLDING

CELL

1060

HOLDING

CELL

1059

HOLDING

CELL

1058

NURSE

WORK AREA

1043

EXAM

1042

MED TOILET

1042A

STORAGE

1062

ISOLATION /

MED CELL

1045

ISOLATION /

MED CELL

1046

ISOLATION /

MED CELL

1047

STAFF

TOILET

1048

MEDICAL

WING

1044

BOOKING

1041

ASSISTANT

JAIL ADMIN

OFFICE

1078

STAFF

TOILET

1079

PROPERTY

STORAGE

1072

ACP210' - 0" AFF

E.T.S.

E.T.S.

E.T.S.

STAIR

1084

D F G J

2

3

4

7

10

E M

6

5

2.2

N

2.6

2x

1x

H L1y

1

E.7 F.5

2y

8

K

9.2

11

1.9

OPEN TO ABOVE

JC

1038

E.T.S.

CORRIDOR

1016A

CORRIDOR

1016B

MSC28' - 0" AFF ACP2

8' - 0" AFF

ACP210' - 0" AFF

GYP510' - 0" AFF

ACP111' - 1" AFF

ACP18' - 0" AFF

GYP48' - 0" AFF

ACP18' - 0" AFF

GYP48' - 0" AFF

ACP18' - 0" AFF

ACP18' - 0" AFF

MSC28' - 0" AFF

ACP28' - 0" AFF

ACP28' - 0" AFF

GYP210' - 0" AFF

GYP38' - 0" AFF

GYP210' - 0" AFF

ACP18' - 0" AFF

GYP18' - 0" AFF

GYP28' - 0" AFF

GYP18' - 0" AFF

ACP28' - 0" AFF

ACP18' - 0" AFF

ACP18' - 0" AFF

ACP18' - 0" AFF

ACP28' - 0" AFF

GYP58' - 0" AFF

ACP18' - 0" AFF

ACP28' - 0" AFF

ACP18' - 0" AFF

GYP28' - 6" AFF

ACP18' - 0" AFF

GYP28' - 0" AFF

MSC28' - 0" AFF

MSC28' - 0" AFF

MSC28' - 0" AFF

MSC28' - 0" AFF

GYP28' - 0" AFF

ACP28' - 0" AFF

2zE.9 K.8

2C

A502

5B

A502

A10.16A10.16

A10.16

A10.16

ELECTRICAL

1062A

E.T.S.

VENDING

1033A

AREA B

AREA A

AR

EA

A

AR

EA

B

AR

EA

B

AR

EA

C

AR

EA

B

AR

EA

C

6D

A515

6D

A515

6E

A504

6B

A504

6E

A515

6E

A515

1" EIFS FOR SOFFIT - SMOOTHFINISH

SOFFIT VENT - 4X24

C JC J

E.T

.S.

ETS

COOLER

1089

FREEZER

1090

KITCHEN

1083

LAUNDRY

1081

ACP110' - 0" AFF

GR

AIN

GR

AIN

7' - 6"

7' - 6"

7' - 4"

7' - 4"

MSC110' - 0" AFF

5'-5 1/4"

A09.22

ETS

EQ

EQ

ACP18' - 0" AFF

ACP18' - 0" AFF

ACP18' - 0" AFF

ACP18' - 0" AFF

GYP411' - 0" AFF

STAIR

1030A

STAIR

1030

GYP510' - 0" AFF

15' - 0"

13' - 0"

15' - 0"

15' - 8"

15' - 0"

15' - 8"

15' - 8"

115' - 0"

A08.28 A08.28

A08.19

A08.19

A09.46 A09.46

A09.46

A09.46

10' - 0"

10' - 0"

10' - 0"

A09.23

A09.23

A09.23 A09.23

A09.23

A09.23

A09.23

A09.23

A09.23

A09.23

A09.23

EJ

EJ

EJ

EJ

EJ

EJ

EJ

EJEJ

EJ

EJ

EJ

EJ

EJ

EJ

EJ

EJ

EJ

EJ

EJ

EJ

EJ

EJ

EJ

EJ

EJ

EJ

EJ

FIXTURE - 12' A.F.F.






15' - 8"

ACP114' - 0" AFF

ACP116' - 0" AFF

ACP116' - 0" AFF

ACP116' - 0" AFF

10' - 0"

ACP110' - 0" AFF

ACP110' - 0" AFF

WD1

CP2

CP2

CP2

CP2

CP2

CP2

CP2

GYP211' - 0" AFF

A09.22GYP2

8' - 0" AFF

A10.26

A10.26A10.26

A10.26

AD2VE

AD2VE

AD2VE

REFLECTED CEILING PLAN LEGEND

SUPPLY - CEILING MOUNT

RETURN DUCT w/ GRILLE -CEILING MOUNT

SUPPLY DUCT w/ GRILLE -CEILING MOUNT

FIRE ALARM SPEAKER-STROBE

EXIT FIXTURE - WALL MOUNT

RECTANGULAR DUCT -CEILING MOUNT

FIRE ALARM STROBE

F

S

F

LED OR FLUORESCENT INDUSTRIAL FIXTURE -CEILING MOUNTED

LED OR FLUORESCENT PENDANT FIXTURE - CEILING MOUNTED

FLUORESCENT FIXTURE -RECESSED IN CEILING

RETURN GRILLE - CEILING MOUNT

2X2 - LAY IN

2X4 - LAY IN

CEILING EQUIPMENT:

HVAC EQUIPMENT:

FIRE PROTECTION EQUIPMENT:

CORNER MOUNT SECURITY FIXTURE

RECESSED SQUARE CAN LIGHT

RECESSED LINEAR LIGHT

SUSPENDED LINEAR LIGHT

REFLECTED CEILING PLAN LEGEND

ACP1: 2' x 2' SQUARE ACOUSTIC CEILING PANELS

GYP1: MOISTURE RESISTANT GYPSUM BOARD CEILING o/ METAL LATH o/ METAL STUD FRAMING AT 16" O.C.

GYP2: GYPSUM BOARD CEILING o/ METAL STUD FRAMING AT 16" O.C.

NOTE: REFER TO FINISH SPECIFICATION LEGEND FOR MORE INFORMATION

ACP2: 2' x 2' SQUARE ACOUSTIC CEILING PANELS w/ SECURITY (HOLD-DOWN) CLIPS

EXPOSED TO STRUCTURE, E.T.S.

MSC2: METAL SECURITY CEILING

CEILING BY OTHERS. NOT PART OF THIS BID PACKAGE.

BAF1: SUSPENDED VERTICAL LINEAR ACOUSTIC PANELS (ACOUSTIC BLADES)

GYP4: MOISTURE RESISTANT GYPSUM BOARD CEILING o/ METAL STUD FRAMING AT 16" O.C.

GYP3: IMPACT RESISTANT GYPSUM BOARD CEILING o/ METAL STUD FRAMING AT 16" O.C.

WD1: WOOD CEILING ASSEMBLY

EQ EQ

VA

RIE

S

SMOOTH FINISH EIFS SYSTEM

MSC1: STAINLESS STEEL METAL SECURITY CEILING

GYP 5: 2-HOUR FIRE-RATED GYPSUM BOARD CEILING o/ METAL STUD FRAMING AT 16" O.C.

4125 W

esto

wn P

kw

y, S

uite 1

00 | W

est D

es M

oin

es, Io

wa 50266

515.2

23.8

104 | fax 5

15.2

23.6

022 | w

ww

.shiv

e-h

attery

.com

6

5

4

3

BA D E

1

FC G

2

Iow

a | Illi

nois

| India

na

DR

AW

N:

AP

PR

OV

ED

:

ISS

UE

D F

OR

:

DA

TE

:

FIE

LD

BO

OK

:

PR

OJE

CT

NO

:

H

BA D E FC G H

6

5

4

3

1

2

Printe

d:

KEY PLAN

A

B

C

CLIN

TO

N C

OU

NT

Y J

US

TIC

E C

EN

TE

R

VE

CO

OR

DIN

AT

ION

SE

T

612

N 2

ND

ST

| C

LIN

TO

N, IA

527

32

A131B

RE

FLE

CT

ED

CE

ILIN

G P

LA

NS

-JA

ILF

OR

CO

NS

TR

UC

TIO

N

41

63

15

0

MS

L

SA

F, K

MH

20

17

-07

-14

TRUE NORTH

NORTHPLAN

1/8" = 1'-0"6CREFLECTED CEILING PLAN - JAIL

KEYNOTE LEGEND

KEY NOTE

A07.21 SOFFIT VENT - 4X24

A07.22 1" EIFS FOR SOFFIT - SMOOTH FINISH

A08.19 12" X24" WALL LOUVER TOP AND BOTTOM OF WALL

A08.28 12X36 SOFFIT VENT

A09.22 ALIGN

A09.23 ALL EXPOSED CEILING AREAS TO BE PAINTED. THISINCLUDES BUT IS NOT LIMITED TO EXPOSEDCONDUIT, STRUCTURE, MECHANICAL DUCT, PIPESAND MISC CEILING DEVICES

A09.46 ACOUSTICAL GRID SYSTEM 6" TRIM RETURN

A10.16 SHOWER CURTAIN ROD

A10.26 FOR ALL EXPOSED STRUCTURAL STEEL SUPPORTINGSECOND LEVEL, CONTRACTOR TO APPLYINTUMESCENT PAINT - COLOR TO MATCH NONPROTECTED EXPOSED STRUCTURAL STEEL

VE

AD

20

8-0

3-2

01

7R

evis

ion

6

5. ALL HORIZONTAL GYPSUM BOARD CEILINGS TO BE PAINTED CP1PER FINISH SPEC SCHEDULE. ALL WET LOCATIONS AND TOILETROOMS TO RECEIVE ECP1 UNO.

4. ALL AREAS NOTED AS MSC1 TO RECEIVE SECURITY SEALANT ATEXPOSED JOINTS AND STRUCTURAL SHELF AND ANGLES, REFERTO STRUCTURAL DRAWINGS FOR LOCATIONS.

3. REFER TO MECHANICAL SCHEDULES FOR DIFFUSER TYPES.

2. REFER TO ELECTRICAL FIXTURE SCHEDULE FOR FIXTURE TYPES.

1. COORDINATE PLACEMENT OF ALL MECHANICAL ELECTRICAL,PLUMBING, FIRE PROTECTION AND SECURITY SYSTEMS WITH THECEILING SYSTEM COMPONENTS, SPECIFICALLY, INCLUDINGACCESS PANEL LOCATIONS. IDENTIFY ANY POTENTIAL CONFLICTSFOR RESOLUTION PRIOR TO INSTALLATION. ALL DEVICES TO BECENTERED IN ACOUSTIC PANEL, UNLESS OTHERWISE NOTED.

CEILING PLAN GENERAL NOTES

SPECIALTY EQUIPMENT SCHEDULE GENERAL NOTES:

PROVIDER/INSTALLER CODES:A CONTRACTOR FURNISHED; CONTRACTOR INSTALLED (CFCI)B CONTRACTOR FURNISHED; OWNER INSTALLED (CFOI)C OWNER FURNISHED; CONTRACTOR INSTALLED (OFCI)D OWNER FURNISHED; OWNER INSTALLED (OFOI)E CONTRACTOR FURNISHED; CONTRACTOR INSTALLED (CFCI)

AS PART OF DETENTION/SECURITY BID PACKAGE

1. ALL NON-TAGGED EQUIPMENT AND FURNITURE SHOWN FOR REFERENCE ONLY.2. REFER TO SEC SHEETS FOR SECURITY EQUIPMENT.3. KEYNOTE LIST IS SPECIFIC TO THIS SHEET.

A111401

A111405 A111405

A111405 A111405

A111406

A111406 A111406 A111406

A111405

A111405

A111407

A111407

A111407

A111407

A111407

A111407

A111407

A111407

A111409

A111409

A111409

A111412

A111412

A111412 A111412

D111418

D111418

D111418

A111423

D111418 A111438

A111450

A111452

A111461

A111461

A111461

C111447

A111443

A111445

A111446

A111442

A111444

A111449

A111426A111426

A111462

A111462

A111428

A111428

A111452

A111451

A111429

A111430

A111434 A111431

A111432

A111456

A111457

A111458

A111458

A111458

A111458 A111454

A111402

A111455

A111455

A111402

A111410

A111448

A111422

A111422

A111403

A111427

A111421

A111436

A111434

A111425

A111420

A111417

A111437

A111440 A111440

A111440A111414 A111415

A111440

A111414 A111415

A111441

A111405A111404

A111404

A111404

D112803

ELECTRICAL

1091

CELL C1

1002A

CELL C2

1002B

JC

1002F

DRY FOOD

STORAGE /

COMMISSARY

1088

CHEM

STORAGE /

JC

1087

DOCK DROP

OFF

1086

FREEZER

1090

COOLER

1089

STAIR

1084

KITCHEN

1083

FOOD

SERVICE -

COOK

1085

A102805

A102805

A102805

A03.01

A03.01

A03.01

A111301

AR

EA

A

AR

EA

B

AR

EA

A

AR

EA

B

A104402

A111439

A111408

A111407

A111407

A111411

A111401

A111419

A111413

A111460

A111411

AD2VE

AD2VE

AD2VE

AD2VE

AD2VE

AD2VE

AD2VE

4125 W

esto

wn P

kw

y, S

uite 1

00 | W

est D

es M

oin

es, Io

wa 50266

515.2

23.8

104 | fax 5

15.2

23.6

022 | w

ww

.shiv

e-h

attery

.com

6

5

4

3

BA D E

1

FC G

2

Iow

a | Illi

nois

| India

na

DR

AW

N:

AP

PR

OV

ED

:

ISS

UE

D F

OR

:

DA

TE

:

FIE

LD

BO

OK

:

PR

OJE

CT

NO

:

H

BA D E FC G H

6

5

4

3

1

2

Printe

d:

CLIN

TO

N C

OU

NT

Y J

US

TIC

E C

EN

TE

R

VE

CO

OR

DIN

AT

ION

SE

T

612

N 2

ND

ST

| C

LIN

TO

N, IA

527

32

A161K

FU

RN

ITU

RE

&E

QU

IPM

EN

TP

LA

N -

KIT

CH

EN

FO

R C

ON

ST

RU

CT

ION

41

63

15

0

MS

L

RC

B

20

17

-07

-14

SPECIALTY EQUIPMENT SCHEDULE

PROVIDER/

INSTALLER TAG ID DESCRIPTION

C 111447 CONVECTION OVEN

D 102801 PAPER TOWEL DISPENSER

D 102802 SOAP DISPENSER

D 102806 TOILET PAPER DISPENSER

D 111418 WASTE CAN

D 111909 CABINET

D 111911 AFIS MACHINE

D 111915 COMMISSARY KIOSK

D 111916 PERSONAL METAL DETECTOR

D 111917 PACKAGE SCANNER

D 111919 VIDEO COURT MONITOR

D 111920 BLOOD DRYING SHELF

D 111922 BREATHALYZER

D 111930 LOCKABLE CABINET

D 111936 VIDEO VISITATION

D 111938 SELF-CONTAINED VENT HOOD

D 111941 WALL CLOCK, MOUNT ABOVE TV

D 111945 VIDEO VISITATION BOOTH

D 111946 DETENTION PAYPHONE

D 111983 SELF-CONTAINED VENT HOOD

D 112801 WORKSTATION FURNITURE - 6'x6' DESK

D 112802 WORKSTATION FURNITURE - 7'x7' DESK

D 112803 WORK STATION CHAIR

D 112804 MOLDED PLASTIC CHAIR

D 112805 OFFICE SIDE CHAIR

D 112806 CREDENZA (LENGTH PER PLAN)

D 112807 FILE CABINET - 4-DRAWER

D 112808 FLOOR COPIER

D 112809 42" DIAMETER CONFERENCE TABLE &CHAIRS

D 112810 OFFICE DESK

D 112811 36" x 60" TABLE

D 112812 MODULAR WORKSTATION & PANELS

D 112813 CONFERENCE TABLE

D 112814 CONFERENCE CHAIR

D 112815 INTERVIEW TABLE

D 112816 T.V.

D 112817 STACKABLE CONFERENCE CHAIRS

D 112818 CONFERENCE FOLDING TABLE

D 112819 ROUND END TABLE

D 112820 CHAIR - WAITING ROOM

D 112821 CHAIR - RECLINER

D 112822 DISPATCH CONTROL TABLE

D 112823 END TABLE

D 112824 BED

D 112825 30" x 72" TABLE

D 112826 DISPATCH WORKSTATION

D 112830 STORAGE PEDISTAL

D 112833 WALL MOUNTED PROJECTION SCREEN

D 112834 GUN REGISTRY KIOSK

D 113101 REFRIGERATOR & FREEZER

D 113102 MICROWAVE

D 113103 ADA UNDERCOUNTER REFRIGERATOR

D 113104 LOCKABLE REFRIGERATOR & FREEZER

D 113105 REFRIGERATOR & FREEZER W/ ICEMAKER

D 114601 VENDING MACHINE

D 117201 EXAM TABLE

E 111901 DETENTION WALL MOUNTED BUNK -DOUBLE

E 111902 DETENTION WALL MOUNTED BUNK -SINGLE

E 111903 DETENTION WALL MOUNTED STOOL

E 111904 DETENTION FLOOR MOUNTED STOOL

E 111905 DETENTION WALL MOUNTED DESK

E 111906 DETENTION STOOL-STYLE TABLE - 4SEATS ROUND


E 111908 DETENTION MIRROR

E 111923 GUN LOCKER


E 111925 SECURITY CONTROL WORKSTATION

E 111926 DETENTION WALL MOUNTED SHELF

E 111927 DETENTION HOOK

E 111928 CUFF BENCH

E 111929 FIRE RATED PACKAGE PASS

E 111932 SHOWER SEAT

E 111933 DETENTION GRAB BARS

E 111934 DETENTION WALL MOUNTED BENCH

E 111935 DETENTION SHOWER CURTAIN

E 111937 DETENTION WALL MOUNTED SWIVELSTOOL

E 111939 LOCKABLE PACKAGE PASS THROUGH

SPECIALTY EQUIPMENT SCHEDULE

PROVIDER/

INSTALLER TAG ID DESCRIPTION

A 088301 3 INCH FRAME PARAMETRIC MIRROR

A 102803 GRAB BARS

A 102804 CHANGING STATION

A 102805 MOP-BROOM HOLDER W/ 3 HOLDERS 24"W

A 102807 SANITARY PRODUCT DISPOSAL UNIT -SURFACE MOUNTED

A 102808 GRAB BARS

A 102810 COAT HOOK

A 102811 SHOWER CURTAIN

A 104401 FULLY RECESSED FIRE EXTINGUISHERCABINET

A 104402 BRACKET MOUNTED FIREEXTINGUISHER

A 104403 PARTIALLY RECESSED FIREEXTINGUISHER

A 104404 PARTIALLY RECESSED DRY FIREEXTINGUISHER

A 104405 SECURE RECESSED FIREEXTINGUISHER CABINET

A 105101 LOCKERS

A 111301 DOCK LIFT

A 111401 MOP SINK. SEE PLUMBING DRAWINGS

A 111402 FLOOR TROUGH

A 111403 PRESSURE CLEANING SYSTEM

A 111404 TRAY RACK - COLD FOOR TRAYS

A 111405 WIRE SHELVING STARTER UNIT

A 111406 WIRE SHELVING STARTER UNIT 18" X 60"

A 111407 WIRE SHELVIN

A 111408 WALK-IN COMBINATION COOLER/FREEZER

A 111409 CAN RACK

A 111410 ICE MACHINE

A 111411 WIRE SHELVING

A 111412 DUNNAGE RACK

A 111413 RACK, POT & PAN

A 111414 SERVING COUNTER

A 111415 SERVING COUNTER

A 111417 RACK SHELF

A 111419 DISHTABLE "L" SHAPE

A 111420 HOSE REEL W/SPRAY

A 111421 PRE-RINSE FAUCET

A 111422 PANT-LEG CONDENSATE DUCTS - BYMECHANICAL

A 111423 DISHWASHER

A 111425 STRAIGHT DISHTABLE


A 111427 THREE-COMPARTMENT SINK W/ 24"DRAIN BOARDS

A 111428 WALL MOUNTED HAND SINK. SEEPLUMBING DRAWINGS.

A 111429 PREP TABLE

A 111430 FOOD SLICER

A 111431 FOOD PROCESSOR

A 111432 WORK TABLE W/ TWO-COMPARTMENTSINK

A 111434 WALL MOUNTED SHELF

A 111436 DISPOSER

A 111437 DISPOSER

A 111438 SHELVING UNIT ON DOLLY TRUCK

A 111439 TRAY MAKE-UP CONVEYOR

A 111440 MEAL TRAY DELIVERY CABINET

A 111441 REFRIGERATOR

A 111442 KETTLE

A 111443 TILTING SKILLET/ BRASING PAN


A 111445 STEEL COOKING GRIDDLE

A 111446 FRYER

A 111448 EXHAUST HOOD W/FIRE SUPPRESSION

A 111449 DISH CART

A 111450 MICROWAVE OVEN

A 111451 CEILING MOUNTED POT RACK

A 111452 WORK TABLE

A 111454 RETHERM OVEN

A 111455 ENCLOSED TRAY TRANSPORT

A 111456 FOOD MIXER

A 111457 WORK TABLE

A 111458 INGREDIENT BIN

A 111460 SCULLERY SINK

A 111461 UTILITY CART


A 111912 PASS-THRU EVIDENCE LOCKER

A 111913 DRYER

A 111914 WASHER

A 111931 REFRIGERATED PASS-THRU EVIDENCELOCKER

A 111942 STATIONARY 24" WIDE CARRIAGE UNIT

A 111943 OPERABLE 36" WIDE CARRIAGE UNITWITH CENTER DIVIDER

A 111944 OPERABLE 24" WIDE CARRIAGE UNITWITH CENTER DIVIDER

A 112803 WORK STATION CHAIR

A 112827 CEILING MOUNTED TV BRACKET

A 112828 PNEUMATIC TUBE

A 112829 WALL MOUNTED TV BRACKET @ 8'-0"AFF, TV PROVIDED BY OWNER, TYP.

A 112831 CEILING MOUNTED PROJECTOR MOUNT,PROJECTOR PROVIDED BY OWNER

A 112832 90" TV MONITOR WALL BRACKET, TVPROVIDED BY OWNER

A 112835 WALL MOUNTED TV BRACKET, TVPROVIDED BY OWNER

A 117202 SHARPS CONTAINER

A 117203 GENERIC WALL MOUNTED GLOVEDISPENSER

A 129401 CROWD CONTROL

TRUE NORTH

NORTHPLAN

1/4" = 1'-0"6E

FURNITURE & EQUIPMENT PLAN - FIRST FLOOR KITCHEN

KEYNOTE LEGEND

KEY NOTE

A03.01 4' H CONCRETE FILLED PIPE BOLLARD.

VE

AD

20

8-0

3-2

01

7R

evis

ion

6

AD2VE

AD2VE

AD2VE

100' - 0"LEVEL 1 - T.O. SLAB

127' - 0"T.O.S. SECOND FLOOR

114' - 0"T.O.S LEVEL 2

119' - 2"LOW Lobby Roof T/T

108' - 4"MEZZANINE

102' - 0"EXIST. LEVEL 1

115' - 1 1/2"EXIST. LEVEL 2

5B

A300

132' - 0"T.O.S. LOBBY

2C

A505

3C

A505

4A

A301

6B

A318

6E

A314

6G

A313

6G

A312 DFGJ EMN HL E.7F.5K

95' - 0"EXISTING BASEMENT

A202

4D

A202

6A

2z E.9K.8

115' - 8"BOT OF LINTEL

117' - 8"HIGH ROOF OFFSET

114' - 8"BOT OF LINTEL2

6B

A319

121' - 8"TOP OF PARAPET

41 41 41 41 41 41 41 41 41

41

135' - 0"TOP OF WALL - HIGH

ROOF

A04.16

A04.16

A04.16

A04.16

A04.16

E J E J E J E J E J E J E J E J E J E J E J E J E J E J E J E J E J E J

100' - 0"LEVEL 1 - T.O. SLAB


114' - 0"T.O.S LEVEL 2

108' - 4"MEZZANINE

125' - 0"T.O.S. HOUSING

118' - 0"T.O.S. VSP

132' - 0"T.O.S. LOBBY

2A

A301

3C

A300

2 3 4 7 9 10652.2 2.61 85.3 9.2 111.9

A08.13

A07.02

A08.10

A04.04

A202

4A

E J E J

E J E J E J E J E JE JE JE JE J

2D

A602

E J

2'-0" 2'-0"

E J E J

A02.07

2C

A300

A07.01A07.01


24'-0" 24'-0" 4'-0"



E JE J E JE J E J E J E J E J E J E J E J E J E J E J E J E J E JE JE JE J


27 27 27 27 27 27 27 27 27

?

27 27 27 27 27


ROOF

E J

100' - 0"LEVEL 1 - T.O. SLAB


114' - 0"T.O.S LEVEL 2

108' - 4"MEZZANINE


4D

A301

132' - 0"T.O.S. LOBBY

123' - 4"T.O.S. FUTURE HOUSING

2D

A301ABCD A.5B.5

A202

4G

A07.02

3'-0"19'-11 5/8" 19'-11 5/8" 20'-0 3/4"

E J E J E J E J




E J E JE JE JE JE JE J E JE J E JE J E JE J E JE J


41 41 41 41 27 27 27 27 27 27 27 27 27


ROOF

AD2VE

E J E J E J E J E J E J E J E J

100' - 0"LEVEL 1 - T.O. SLAB

114' - 0"T.O.S LEVEL 2

108' - 4"MEZZANINE

1011

E J

3'-0" 3'-0"

E J

A07.02

A07.02



100' - 0"LEVEL 1 - T.O. SLAB

118' - 0"T.O.S. VSP

2A

A301

10 11

A07.02

A08.12

3'-0"

E JE JE JE JE J




100' - 0"LEVEL 1 - T.O. SLAB

3'-0" 3'-0"

E J E J E J

A02.07



APPLY BRICK PATTERN TO MAINTENANCE BUILDING FACADE - ALL ELEVATIONS -TYPICAL. MAINTENANCE BUILDING WALLS CAN BE UTILIZED FOR MOCK UP PURPOSES. SEE 5D/6D A202 FOR BRICK PATTERN DIAGRAMS

100' - 0"LEVEL 1 - T.O. SLAB

F.V

.

15

'-4

"

3'-0" 3'-0"

E J E J

A07.02


100' - 0"LEVEL 1 - T.O. SLAB

E J E J E J E J E J E J

AD.01AD.01

AD.02AD.02

FIE

LD

VE

RIF

Y

10

'-0

"

6B

A515

A02.07

6Ea

A515

A02.09

A02.09

A02.08

6E

A515


100' - 0"LEVEL 1 - T.O. SLAB

E J E J E J E J

3'-0" 3'-0"

A02.07

6D

A515

5D

A515

A02.08115' - 8"

BOT OF LINTEL

4125 W

esto

wn P

kw

y, S

uite 1

00 | W

est D

es M

oin

es, Io

wa 50266

515.2

23.8

104 | fax 5

15.2

23.6

022 | w

ww

.shiv

e-h

attery

.com

6

5

4

3

BA D E

1

FC G

2

Iow

a | Illi

nois

| India

na

DR

AW

N:

AP

PR

OV

ED

:

ISS

UE

D F

OR

:

DA

TE

:

FIE

LD

BO

OK

:

PR

OJE

CT

NO

:

H

BA D E FC G H

6

5

4

3

1

2

Printe

d:

CLIN

TO

N C

OU

NT

Y J

US

TIC

E C

EN

TE

R

VE

CO

OR

DIN

AT

ION

SE

T

612

N 2

ND

ST

| C

LIN

TO

N, IA

527

32

A200

EX

TE

RIO

RE

LE

VA

TIO

NS

-N

OR

TH

& W

ES

TF

OR

CO

NS

TR

UC

TIO

N

41

63

15

0

MS

L

DLP

20

17

-07

-14

1/8" = 1'-0"2ANORTH ELEVATION - LOBBY

1/8" = 1'-0"5B

WEST ELEVATION

KEYNOTE LEGEND

KEY NOTE

A02.07 OWNER WILL PROVIDE NEW METAL COPING CAP UNDERSEPARATE CONTRACT.

A02.08 EXISTING DOOR

A02.09 EXISTING OVERHEAD DOOR

A04.04 FACE BRICK, FIELD, UTILITY SIZE - MORTAR PATTERN A

A04.16 BRICK TYPE 2 - DARK GREY BRICK - SEE 5D/6D A202

A07.01 ALUMINUM METAL PLATE WALL PANELS

A07.02 PREFINISHED METAL COPING

A08.10 ALUMINUM CURTAIN WALL

A08.12 OVERHEAD DOOR

A08.13 SECURITY SCREEN WITH OVERHEAD COILING SHUTTER

AD.01 OWNER WILL REMOVE EXISTING SCUPPER AND DOWNSPOUTAND INSTALL NEW LEADERHEAD AND DOWNSPOUT UNDERSEPARATE CONTRACT.

AD.02 REMOVE AND REINSTALL EXISTING LIGHT WITH BOXEXTENDER

1/8" = 1'-0"4CNORTH ELEVATION - HOUSING

1/8" = 1'-0"4APARTIAL ELEVATION EAST LOADING DOCK

1/8" = 1'-0"5A

PARTIAL WEST ELEVATION -VSP

1/8" = 1'-0"6A

MAINTENANCE BUILDING - NORTH ELEVATION 1/8" = 1'-0"

6CMAINTENANCE BUILGING - EAST ELEVATION

1/8" = 1'-0"6E

MAINTENANCE BUILDING - SOUTH ELEVATION 1/8" = 1'-0"

6GMAINTENANCE BUILDING - WEST ELEVATION

BP

4A

D3

03

-16

-201

7R

evis

ion

4

VE

AD

20

8-0

3-2

01

7R

evis

ion

6

MORTAR TYPES:

MORTAR 1: RAKED JOINTSMORTAR 2: FLUSH JOINTSMORTAR PATTERN A: 3-COURSES MORTAR 2 FLUSH JOINTS 1-COURSE MORTAR 1: RAKED BED JOINTS WITH FLUSH HEAD JOINTS

100' - 0"LEVEL 1 - T.O. SLAB


114' - 0"T.O.S LEVEL 2

108' - 4"MEZZANINE


115' - 1 1/2"EXIST. LEVEL 2


5B

A300

118' - 0"T.O.S. VSP

132' - 0"T.O.S. LOBBY

2D

A301

4A

A301

D F G JE M NH LE.7 F.5 K

A07.01

A08.09

A08.09

A08.12

139' - 0 1/16"EXIST. LEVEL 4

3'-0"2'-8" 3'-0" 3'-0" 6'-0"

E J E J E J E J E J E J E J

3'-0"

E J

E JE J

E JE J

E JE JE JE J

E J

E JE J E J

E J E J E J E J E J E J E J E J E J E J E J E J E J E J E J E J E JE J E J E JA07.02

E JE J E J E JE J

A02.07

5B

A505

BASE BID INCLUDES SOUTH CANOPY. BID ALTERNATE #5 IS WITHOUT SOUTH CANOPY.

E J E J



ROOF

E JE J

AD2VE

100' - 0"LEVEL 1 - T.O. SLAB


114' - 0"T.O.S LEVEL 2

5.3

108' - 4"MEZZANINE


115' - 1 1/2"EXIST. LEVEL 2

6A

A301

118' - 0"T.O.S. VSP

132' - 0"T.O.S. LOBBY

2A

A301

3C

A300

A311

6D

34710 6 5 2.22.6 189.211

3'-0"

E J E J E J E J E J E J E J



3'-0"

A07.02

A07.02

A04.10

A04.05

E J E J

A08.09

6'-0"

2'-0

"




E J

E J



ROOF

95 95AD2VE

100' - 0"LEVEL 1 - T.O. SLAB

114' - 0"T.O.S LEVEL 2

108' - 4"MEZZANINE

110' - 4"CONTROL ROOM


4D

A301 132' - 0"T.O.S. LOBBY

2D

A301

6A

A314

A B C DA.5 B.5

3'-0"

E J E J

E J E J E J E J

E J E J

E J E J

E JE JA07.02

A04.05

A04.10

A03.01

A02.07

A07.01

E J

3'-0"

A08.09

A08.09

20'-0" 24'-0" 24'-0"

E JE J E J E J E J E J E J E J E J E J E J E J E J E J E JE J


27 27 27 27 27 27 27 27 27 27


ROOF

4125 W

esto

wn P

kw

y, S

uite 1

00 | W

est D

es M

oin

es, Io

wa 50266

515.2

23.8

104 | fax 5

15.2

23.6

022 | w

ww

.shiv

e-h

attery

.com

6

5

4

3

BA D E

1

FC G

2

Iow

a | Illi

nois

| India

na

DR

AW

N:

AP

PR

OV

ED

:

ISS

UE

D F

OR

:

DA

TE

:

FIE

LD

BO

OK

:

PR

OJE

CT

NO

:

H

BA D E FC G H

6

5

4

3

1

2

Printe

d:

CLIN

TO

N C

OU

NT

Y J

US

TIC

E C

EN

TE

R

VE

CO

OR

DIN

AT

ION

SE

T

612

N 2

ND

ST

| C

LIN

TO

N, IA

527

32

A201

EX

TE

RIO

RE

LE

VA

TIO

NS

-S

OU

TH

& E

AS

TF

OR

CO

NS

TR

UC

TIO

N

41

63

15

0

MS

L

DLP

, R

CB

20

17

-07

-14

1/8" = 1'-0"2A

SOUTH ELEVATION - JAIL

1/8" = 1'-0"6BEAST ELEVATION

KEYNOTE LEGEND

KEY NOTE

A02.07 OWNER WILL PROVIDE NEW METAL COPING CAPUNDER SEPARATE CONTRACT.

A03.01 4' H CONCRETE FILLED PIPE BOLLARD.

A04.05 FACE BRICK, ACCENT, UTILITY SIZE - MORTAR 1

A04.10 FACE BRICK, FIELD, UTILITY SIZE- MORTAR 1

A07.01 ALUMINUM METAL PLATE WALL PANELS


A08.09 BASE BID: ALUMINUM CURTAIN WALL

A08.12 OVERHEAD DOOR

1/8" = 1'-0"4DSOUTH ELEVATION - HOUSING

VE

AD

20

8-0

3-2

01

7R

evis

ion

6

MORTAR TYPES:


114' - 0"T.O.S LEVEL 2


132' - 0"T.O.S. LOBBY

6E

A315

7910 89.2

A07.02

A08.09

A05.22



ROOF

E J E J

AD2VE


114' - 0"T.O.S LEVEL 2

132' - 0"T.O.S. LOBBY

3E

A505

6A

A3167 8

A04.05

E JE J



ROOF


114' - 0"T.O.S LEVEL 2

132' - 0"T.O.S. LOBBY

A08.09

2424121' - 8"

TOP OF PARAPET


ROOF

E J E J

E J E J


114' - 0"T.O.S LEVEL 2

5B

A300

6G

A313

F HE.7 F.5 K

A04.10

A08.09

24 24 24 24 24 24 24121' - 8"

TOP OF PARAPET

100' - 0"LEVEL 1 - T.O. SLAB


114' - 0"T.O.S LEVEL 2


C

A202

6GE JE JE JE JE J

E JE JE JE J






ROOF

100' - 0"LEVEL 1 - T.O. SLAB

C

MORTAR TYPES:


2'-8

"

ALIGN. WITH COLUMN BASE OFFSET

STOP PATTERN AT 117'-8" HIGH ROOF OFFSET

3 COURSES MORTAR 2

1 COURSE MORTAR 1

3 COURSES MORTAR 2

1 COURSE MORTAR 1

1 COURSE MORTAR 1

3 COURSES MORTAR 2

MORTAR 2 UP ALIGN WITH WATERFALL BRICK AT LOBBY

AREA COLUMNS

SEE 6E / A202 FOR

MORTAR PATTERN

LOCATION DIAGRAM

100' - 0"LEVEL 1 - T.O. SLAB

5B

A300

132' - 0"T.O.S. LOBBY

GJ H2z

EJ AT CORNER

EJ AT CORNER

E J

ALUMINUM CURTAINWALL






ROOF

E J E J E J E J E J

E J E J E J E J E J

100' - 0"LEVEL 1 - T.O. SLAB

132' - 0"T.O.S. LOBBY

21 1.9

E JE J

ALUMINUM CURTAINWALL






ROOF

2'-0"2'-0"

E J E J E J E J

100' - 0"LEVEL 1 - T.O. SLAB

132' - 0"T.O.S. LOBBY

6G

A312

F EE.7E.9

E JE J

ALUMINUM CURTAIN WALL





6B

A319



ROOF

E J

4125 W

esto

wn P

kw

y, S

uite 1

00 | W

est D

es M

oin

es, Io

wa 50266

515.2

23.8

104 | fax 5

15.2

23.6

022 | w

ww

.shiv

e-h

attery

.com

6

5

4

3

BA D E

1

FC G

2

Iow

a | Illi

nois

| India

na

DR

AW

N:

AP

PR

OV

ED

:

ISS

UE

D F

OR

:

DA

TE

:

FIE

LD

BO

OK

:

PR

OJE

CT

NO

:

H

BA D E FC G H

6

5

4

3

1

2

Printe

d:

CLIN

TO

N C

OU

NT

Y J

US

TIC

E C

EN

TE

R

VE

CO

OR

DIN

AT

ION

SE

T

612

N 2

ND

ST

| C

LIN

TO

N, IA

527

32

A202

EX

TE

RIO

RE

LE

VA

TIO

NS

-E

NLA

RG

ED

ELE

VA

TIO

NS

FO

R C

ON

ST

RU

CT

ION

41

63

15

0

MS

L

DLP

20

17

-07

-14

1/8" = 1'-0"2BPARTIAL EAST ELEVATION - HOUSING LEVEL 2

1/8" = 1'-0"2APARTIAL WEST ELEVATION - LEVEL 2

1/8" = 1'-0"D2PARTIAL EAST ELEVATION - LEVEL 2

1/8" = 1'-0"E2PARTIAL SOUTH ELEVATION - LEVEL 2

1/4" = 1'-0"4G

ENLARGED NORTH ELEVATION

KEYNOTE LEGEND

KEY NOTE

A04.05 FACE BRICK, ACCENT, UTILITY SIZE - MORTAR1

A04.10 FACE BRICK, FIELD, UTILITY SIZE- MORTAR 1

A05.22 ROOF ACCESS LADDER


A08.09 BASE BID: ALUMINUM CURTAIN WALL

A08.10 ALUMINUM CURTAIN WALL

3/4" = 1'-0"6GMORTAR PATTERN DETAIL

1/4" = 1'-0"4D

ENLARGED NORTH ELEVATION - LOBBY 1/4" = 1'-0"

4AENLARGED WEST ELEVATION

1/4" = 1'-0"6A

ENLARGED NORTH ELEVATION - LOBBY

VE

AD

20

8-0

3-2

01

7R

evis

ion

6

MORTAR TYPES:


5DMORTAR TYPE DIAGRAM

NO MORTAR PATTERN FOR JAIL HOUSING

APPLY MORTAR PATTERN TO AL MASONRY THIS SIDE OF BUILDING

APPLY MORTAR PATTERN TO FACILITIES BUILDING FACADE. NOTE: THIS SEPARATED BUILDING MAY BE USED FOR MOCK UP WALL CONTRUCTION OF MOTAR PATTERNS

6D

BRICK COLOR / TYPELOCATION DIAGRAM

BRICK COLOR 2 - DARK BRICK

BRICK COLOR 2 - DARK BRICK

NOTE: ALL OTHER AREAS, BRICK COLOR 1 -RED BRICK

5/8" GYPSUM BOARD

METAL STUD FRAMING, SEE PARTITION TYPES

SEALANT, BOTH SIDES

GLAZING

EQ EQ

5/8" GYPSUM BOARD


SEALANT w/ BACKER ROD, BOTH SIDES

GLAZING

ALUMINUM STOREFRONT

TYPE 17 TYPE 182

"

3'-8

"

2"

3'-2

"

TYPE 24

2" 3'-8" 2"

IG-2

TYPE 13

2"

3'-8

"

2"

3'-2

"

2" 5'-9" 2" 5'-9" 2"

TYPE 26

2"

3'-8

"

2"

2" 2'-0" 2"

FIELD VERIFY OPENING IN EXISTING WALL

2"

3'-8

"

2"

4'-0

"

2AA603

4AA603

45 MINUTE RATED FRAME AND GLASS-COLOR TO MATCH EXISTING

NOTE: FIELD VERIFY ALL OPENINGS PRIOR TO ORDERING - TYPICAL

5AA603

6AA603

TYPE 28

EXTERIOR WINDOW

5'-0

"

3'-2"

REPLACEMENT WINDOW TO MATCH MULLIONS, COLOR, MATERIAL AND GLAZING COLOR OF WINDOW SYSTEMS IN ADJACENT EXISTING COURTHOUSE

2"

3'-8

"

2"

3'-2

"

2" 3'-8" 2"

TYPE 11

2"

3'-8

"

2"

3'-0

"

2"

5'-8"

2"

2" 5'-8" 2"

TYPE 95

7'-1 3

/8"

2"

1'-8

"2

"

2" 5'-8" 2"

IG-2

IG-2

G-1 G-1 G-1 RG-2G-1G-1

6'-0

"

4'-0"

2"

5'-8

"2

"

2" 3'-8" 2"

TYPE 41

EXTERIOR WINDOW

4'-0"

4'-0

"

2"

3'-8

"2

"

2"3'-8"

2"

TYPE 27

AD2VE

5/8" GYPSUM BOARD


SEALANT, BOTH SIDES

GLAZING

STOREFRONT FRAMING

EQEQ

5/8" GYPSUM BOARD

METAL STUD BOX HEADER

SEALANT, BOTH SIDES

GLAZING

EQ EQ

5/8" GYPSUM BOARD


SEALANT, BOTH SIDES

FIRE-RATED STRUCTURAL GLAZING

FIRE-RATED STOREFRONT FRAMING

EQEQ

BLOCKING w/ MINERAL WOOL FILLER

METAL CORNER BEAD

5/8" GYPSUM BOARD

SEALANT, BOTH SIDES



MINERAL WOOL FILLER

EQEQ

METAL STUD FRAMING

METAL CORNER BEAD

5/8" GYPSUM BOARD

METAL STUD BOX HEADER



MINERAL WOOL FILLER

EQEQ

METAL STUD FRAMING

SEALANT, BOTH SIDES

METAL CORNER BEAD

GLAZING TYPE GLASS COMPONENTS

IG-1 INSULATED GLAZING UNIT

IG-2 INSULATED GLAZING UNIT - TINTED

RG-1 FRAMELESS INTERIOR FIRE RATED GLAZED OPENING

RG-2 INTERIOR FIRE RATED GLAZED OPENING

G-1 INTERIOR VISION GLAZING

G-2 INTERIOR SAFTEY GLAZING

G-3 INTERIOR FIRE RATED SAFTEY GLAZING

6A

A501

2'-9 5/8"3'-5 1/4" (+ / -)3'-0"

5F

A603

6D

A603

6D

A603

6G

A604

4F

A603

2'-10

"7

'-2

"

7'-0

"

FIRE RATED STRUCTURAL GLAZING, INTUMESCENTSEALANT @ BUTT JOINTS AND FIRE-RATED MULLIONS.

4EA604

5E

A60

4

10

'-0

"

3'-5 1/4"

7'-0

"

4'-0

"

15'-0"

3'-9" 3'-9" 3'-9" 3'-9"

IG-1

4125 W

esto

wn P

kw

y, S

uite 1

00 | W

est D

es M

oin

es, Io

wa 50266

515.2

23.8

104 | fax 5

15.2

23.6

022 | w

ww

.shiv

e-h

attery

.com

6

5

4

3

BA D E

1

FC G

2

Iow

a | Illi

nois

| India

na

DR

AW

N:

AP

PR

OV

ED

:

ISS

UE

D F

OR

:

DA

TE

:

FIE

LD

BO

OK

:

PR

OJE

CT

NO

:

H

BA D E FC G H

6

5

4

3

1

2

Printe

d:

CLIN

TO

N C

OU

NT

Y J

US

TIC

E C

EN

TE

R

VE

CO

OR

DIN

AT

ION

SE

T

612

N 2

ND

ST

| C

LIN

TO

N, IA

527

32

A604

INT

ER

IOR

ST

OR

EF

RO

NT

&C

UR

TA

INW

ALL

TY

PE

S, D

ET

AIL

SA

ND

GE

NE

RA

LIN

FO

RM

AT

ION

FO

R C

ON

ST

RU

CT

ION

41

63

15

0

MS

L

KM

H

20

17

-07

-14

3" = 1'-0"4GALUMINUM STOREFRONT JAMB - STUD WALL

3" = 1'-0"5GALUMINUM STOREFRONT JAMB - STUD WALL

1/4" = 1'-0"

FRAME ELEVATIONS - NON-DETENTION

3" = 1'-0"6G

ALUMINUM STOREFRONT SILL - STUD WALL

3" = 1'-0"3G

ALUMINUM STOREFRONT HEAD - STUD WALL

3" = 1'-0"6E

FIRE-RATED STOREFRONT SILL - STUD WALL

3" = 1'-0"5EFIRE-RATED STOREFRONT JAMB - STUD WALL

3" = 1'-0"4EFIRE-RATED STOREFRONT HEAD - STUD WALL

BP

4A

D3

03

-16

-201

7R

evis

ion

4

VE

AD

20

8-0

3-2

01

7R

evis

ion

6

1/4" = 1'-0"2ESF-INT-5

1/4" = 1'-0"2DSF-INT-4

1/4" = 1'-0"15TYPE 15

AD2VE

1 1x

HSS4x4x1/4

W8x13

HSS4x4x1/4

T/PIER

100'-8"

T/S

108'-8"

T/S

116'-6"

T/S

119'-2"

COLUMN PER PLAN

COLUMN PER PLAN

4' - 0"

S201

2D

S201

6B

DESIGN ANGLE BRACING THIS ELEVATION FOR 5k TENSION AND 5k COMPRESSION

W10x15

W10x15

SIMS201

6ASIM

HSS6x6x1/4

1' - 8 1/4"

SIM

E.7E.9

3' - 5 5/8"

W8x13

HSS4x4x1/4

COLUMN PER PLAN

COLUMN PER PLAN

S201

2D


HSS4x4x1/4

W10x15

T/PIER

100'-8"

T/S

108'-8"

T/S

116'-6"

T/S

119'-2"

W10x15

S201

6A

S201

6B

1

HSS4x4x1/4

W8x13

HSS4x4x1/4

4' - 3 3/4"

1x

COLUMN PER PLAN

COLUMN PER PLAN

S201

2D

S201

6B


SIM

SIM

S201

6A

W10x15

W10x15

SIM

T/PIER

100'-8"

T/S

108'-8"

T/S

116'-6"

T/S

119'-2"

11x

HSS6x4x1/4

W8x24

HSS6x4x1/4

COLUMN PER PLAN

COLUMN PER PLAN

11' - 10"

T/PIER

100'-8"

T/S

108'-8"

T/S

119'-2"

S201

6A

S201

2D


W18x35

L K.8

T/PIER

100'-8"

3' - 5 5/8"

HSS4x4x1/4

W8x13

HSS4x4x1/4

COLUMN PER PLAN

COLUMN PER PLAN

S201

2D


T/S

108'-8"

T/S

119'-2"

1 1x

W8x24

COLUMN PER PLAN

COLUMN PER PLAN

S201

2D

11' - 6 3/8"


HSS6x4x1/4

HSS6x4x1/4

HSS6x6x1/4

W18x35

T/PIER

100'-8"

T/S

108'-8"

T/S

119'-2"

HSS4x4x1/4

W8x13

HSS4x4x1/4

T/PIER

100'-8"

LK.8

3' - 5 5/8"

COLUMN PER PLAN

COLUMN PER PLAN

S201

2D


W14x22

T/S

108'-8"

T/S

119'-2"

B A.5B.5

W16x36 W16x36

HSS6x6x1/4 HSS6x6x1/4

W10x49

HSS6x6x1/4H

SS6x6x1/4H

SS4x4x1/4

W10x49

HSS6x6x1/4HSS6x6x1/4

HSS6x6x1/4

DBE 125'-0"

T/S 113'-6 1/2"

FFE 100'-0"

(8K COMPRESSION,

8K TENSION) (8K COMPRESSION,

8K TENSION)

(8K COMPRESSIO

N,

8K TENSION)

(8K COMPRESSION,

8K TENSION)

(8K COMPRESSION,

8K TENSION)

(8K COMPRESSIO

N,

8K TENSION) (8

K COMPRESSION,

8K TENSION)

(8K COMPRESSIO

N,

8K TENSION)C

OLUMN PER PLAN

COLUMN PER PLAN

COLUMN PER PLAN

26' - 11"26' - 11"

S201

5B

S201

5A

S201

6A

TYP8"

BA.5 B.5

W16x36 W16x36


W10x49

HSS6x6x1/4H

SS6x6x1/4

W10x49

HSS6x6x1/4HSS6x6x1/4

HSS6x6x1/4 H

SS6x6x1/4

(8K COMPRESSION,

8K TENSION)

(8K COMPRESSIO

N,

8K TENSION)

(8K COMPRESSION,

8K TENSION)

(8K COMPRESSION,

8K TENSION)

(8K COMPRESSION,

8K TENSION)

(8K COMPRESSION,

8K TENSION)

(8K COMPRESSIO

N,

8K TENSION)

(8K COMPRESSION,

8K TENSION)

COLUMN PER PLAN

COLUMN PER PLAN

COLUMN PER PLAN

26' - 11" 26' - 11"

DBE 125'-0"

T/S 113'-6 1/2"

FFE 100'-0"

S201

5B

S201

5A

S201

6A

TYP8"

3 4 7 9

W21x44

HSS6x6x1/4H

SS6x6x1/4

W10x49

HSS6x6x1/4H

SS6x6x1/4

HSS6x6x1/4 H

SS6x6x1/4

W10x49

HSS6x6x1/4H

SS6x6x1/4

W21x44W14x48

5.2 6.2

(9K COMPRESSIO

N,

5K TENSION) (9

K COMPRESSION,

5K TENSION)

(14K COMPRESSION,

9K TENSION)

(14K COMPRESSION,

9K TENSION)

(9K COMPRESSIO

N,

5K TENSION)

(9K COMPRESSION,

5K TENSION)

(14K COMPRESSION,

9K TENSION)

(14K COMPRESSION,

9K TENSION)

DBE 125'-0"

5"

FFE 100'-0"

20' - 6" 10' - 3" 20' - 6" 10' - 3" 20' - 6"

COLUMN PER PLAN

COLUMN PER PLAN

COLUMN PER PLAN

COLUMN PER PLAN

COLUMN PER PLAN

COLUMN PER PLAN

T/S 113'-6 1/2"

S201

5A

S201

5B

S201

6A

W10x49 W10x49

TYP8"

S513

5E

W10x49

2"

MIN

4"

BRACE W.P.

BRACE

SLOTTED HSS BRACE PER PLAN

ERECTION BOLT

-

T/FTG

PER PLAN

GUSSET PLATE (3/8" MINIMUM)

NOTE: STEEL FABRICATOR TO SIZE GUSSET PLATE, WELDS AND CONNECTIONS FOR FORCES INDICATED ON PLAN AND THE BRACED FRAME ELEVATIONS

COLUMN PER PLAN

1"


DEPTH

1/2 BM

BRACE W.P.

ERECTION BOLT

BEAM PER PLAN

T/S

113'-6 1/2"


SLOTTED HSS BRACE PER ELEVATION

4" MIN


-

DEPTH

1/2 BEAM

T/S

PER PLAN

DOUBLE CLIP ANGLE CONN. w/ 3/4"ø BOLTS (FULLY PRETENSION)

BRACE

BRACE W.P.

COLUMN PER PLAN (FLANGE NOT SHOWN FOR CLARITY)

ERECTION BOLT



BEAM PER PLAN

1"

MIN.

4"

METAL DECK PER PLAN, ORIENTATION VARIES

-


ANGLE BRACE PER ELEVATION

BRACE

COLUMN PER PLAN

BRACE W.P.

T/FTG

PER PLAN

1"


5.2 6.2

DBE

125'-0"

B/S

123'-3"

T/WALL

118'-0"

20' - 6"

4' - 9 5/8" 8' - 6" 4' - 2"

HSS6x6x1/4

HSS6x6x1/4

HSS6x6x1/4

OPEN

5C

S513

6C

S512

5E

S511


L8x6x3/8xCONT LEDGER NOT SHOWN FOR CLARITY

W14x48

INSIDE FACE OF CMU

INSIDE FACE OF CMU

NOTE: STEEL FABRICATOR TO SIZE GUSSET PLATE, WELDS AND CONNECTIONS TO COLUMNS FOR FORCES INDICATED ON PLAN AND THE BRACED FRAME ELEVATIONS

BEAM PER PLAN


DOUBLE CLIP ANGLE CONN. w/ 3/4"Ø BOLTS

COLUMN PER PLAN

BRACE

BRACE W.P.

GUSSET PLATE(1/2" MINIMUM)

ERECTION BOLT

DEPTH

1/2 BEAM

T/S

PER PLAN

-

BRACE


GUSSET PLATE(3/8" MINIMUM)

ERECTION BOLT

TYPTYP

4125 Westown Pkwy, Suite 100 | West Des Moines, Iowa 50266

515.223.8104 | fax 515.223.6022 | www.shive-hattery.com

6

5

4

3

BA D E

1

FC G

2

Iowa | Illinois | Indiana

DRAWN:

APPROVED:

ISSUED FOR:

DATE:

FIELD BOOK:

PROJECT NO:

H

BA D E FC G H

6

5

4

3

1

2

Printed:

CLINTON COUNTY JUSTICE CENTER

VE COORDINATION SET

612 N 2ND ST | CLINTON, IA 52732

S201

BRACING

ELEVATIONS

FOR CONSTRUCTION

4163150

ASC

JRM

2017-07-14

0 1/4" = 1'-0"4EGRID E.7 BRACING

6' 0 1/4" = 1'-0"4FGRID 1 BRACING

6' 0 1/4" = 1'-0"4HGRID E.9 BRACING

6'

0 1/4" = 1'-0"6DGRID L BRACING

6' 0 1/4" = 1'-0"6EGRID 1 BRACING

6' 0 1/4" = 1'-0"6FGRID K.8 BRACING

6' 0 1/4" = 1'-0"6HGRID 1x BRACING

6'

0 1/8" = 1'-0"3ABRACING ELEVATION GRID 2

12' 0 1/8" = 1'-0"3CBRACING ELEVATION GRID 10

12'

0 1/8" = 1'-0"2ABRACING ELEVATION - GRID A

12'

0 1" = 1'-0"5ABRACING DETAIL AT COL BASE

1'-6" 0 1" = 1'-0"5BBRACING CONN. AT BEAM MIDPOINT

1'-6"

0 1" = 1'-0"6A

BRACING DETAIL AT TOPOF COL

1'-6"

0 1" = 1'-0"2DBRACING DETAIL

1'-6"

0 1/4" = 1'-0"2EBRICK SUPPORT ELVATION

6'

0 1" = 1'-0"6BHSS BRACING DETAIL

1'-6"