9' vertical lift with slide-out keyboard tray for flat panel ... cardboard spacer until...

1 of 22888-25-003-02 rev.F • 1/04

Ergonomic Mounting Height Instructions . . . 2

Required Tools . . . . . . . . . . . . . . . . . 2

Components. . . . . . . . . . . . . . . . . . . 3

Wall Anchorage Requirements . . . . . . . . 4 OSHPD . . . . . . . . . . . . . . . . . . 5 Standard . . . . . . . . . . . . . . . . . 7

Monitor Attachment . . . . . . . . . . . . . . 9

Keyboard Attachment . . . . . . . . . . . . .12

Dimensions . . . . . . . . . . . . . . . . . . .16

Adjustment. . . . . . . . . . . . . . . . . . .17

Cover Installationand Cable Routing . . . . . . . . . . . . . . .20

Trouble Shooting. . . . . . . . . . . . . . . .22

USA 1-800-888-8458Europe +31 20 312.29.39

9" Vertical Lift with Slide-out Keyboard Tray for Flat

Panel Monitor & KeyboardOSHPD Mount or Standard Mount

User's Guide

WARNING: Ergotron's Wall Mounted 9" Vertical Lift must be securely attached to your wall. Because wall construction varies widely and your ultimate mounting method is out of Ergotron’s control, it is imperative that you consult with appropriate local engineering, architectural, or construction personnel to ensure that the 9" Vertical Lift is mounted properly to handle applied loads.

2 of 22888-25-003-02 rev.F • 1/04

1 Determine Ergonomic Mounting Height

- M"

51.5"- M"

M

(1,714.5mm)

=H"

=H"

TO FLOOR

H" (H mm)

21

21

NO OSHPD REVIEW REQUIRED

3 of 22888-25-003-02 rev.F • 1/04

A B C D E

1

2

3

4

5

6

7

#8-324x

M4x10mm M4x20mm

4x

1/4-20 x 1-1/2"

4x4x4x8x

4x

1x

1x

1x2x

2x 1x

2x

1x

5/32"(3 97mm)

( )

3/16"(4 76mm)

( )

7.825198.755

2.08853.023

30.125765.175

12.000304.800

.88822.543

27.750704.850

4X Ø .500PILOT HOLE

12.700

PILOT HOLE

X

OUTLINE OF 9"VERTICAL LIFT SYSTEM

MOUNTING HEIGHT EQUATION FOR SITTINGAPPLICATIONS:

52.00 (1321MM) - X = H

X = DISTANCE FROM THE TOP OF THE MONITORSCREEN TO THE CENTER OF THE MOUNTINGSCREW PATTERN (SEE PICTORIAL)

H = HEIGHT FROM FLOOR TO MOUNTING HEIGHTLINE (ABOVE)

MOUNTING HEIGHT LINE:(OBTAINED BY SOLVINGEQUATION BELOW)

MOUNTING HEIGHT EQUATION FOR STANDINGAPPLICATIONS:

67.50 (1715MM) - X = H

X = DISTANCE FROM THE TOP OF THE MONITORSCREEN TO THE CENTER OF THE MOUNTINGSCREW PATTERN

H = HEIGHT FROM FLOOR TO MOUNTING HEIGHTLINE (ABOVE)

1. REFER TO THE MANUAL.

2. MEASURE THE DISTANCE FROM THE TOP OF THE MONITOR

SCREEN TO THE CENTER OF THE MOUNTING SCREW PATTERN.

3. DETERMINE ERGONOMICLLY CORRECT VIEWING HEIGHT BY

USING EQUATION ABOVE (OR BELOW).

4. MARK THE DETERMINED VALUE FOR H, ON THE WALL.

5. ALIGN MOUNTING HEIGHT LINE TO MARK ON THE WALL.

USING A LEVEL, LEVEL THE TEMPLATE, THEN TACK IN PLACE.

6. CLEARLY MARK THE POSITIONS FOR FOUR PILOT HOLES

INTO THE WALL.

7. DRILL THE FOUR PILOT HOLES.

H H

ERGOTrON

SIZE DWG. NO.

DREV.

DATEDRAWN CHECKED

TITLE

C888-122MJS 1/21/99

MANUAL,VISUAL GUIDE,TEMPLATE,TO MOUNT 9" VERTICAL LIFT SYSTEMTO WALL

OBSOLETEPART NUMBER

888-122STATUS

888-122-01 ACTIVE - AS SHOWN

HCS

#8-32 x 3/16"

10x

#8-32 x 3/8"

2x

3/32"(2 38mm)

1/8"(3 15mm)

1x

Mounting Hole Template1x

#8-32 x 5/16"

2x

10x

CAUTION: Do Not remove cardboard spacer until instructed to do so.


4 of 22888-25-003-02 rev.F • 1/04

METHOD ALIGHT GAUGE METAL STUD WALLS

METHOD BWOOD STUD WALLS OSHPD OSHPD

5 6

WARNING: Follow these instructions to ensure that the Ergotron 9" Vertical Lift is mounted according to standards established by OSHPD to handle applied loads. Failure to comply with standards established by OSHPD may result in property damage and personal injury.

2 Wall Anchorage RequirementsCalifornia OSHPD Anchorage Pre-approval Number OPA-0620 In compliance with standards established for the anchorage and installation of instrument support sys-tems by the California Offi ce of Statewide Health Planning and Development (OSHPD), Ergotron, Inc. has obtained pre-approval for two 9" Vertical Lift mounting methods. These mounting methods are limited to use with the following components on the following types of walls: a Light Gauge Metal Stud Walls (24 gauge minimum) - page 5 b Wood Stud Walls (#2 Him Fir, Douglas Fir or better) - page 6The Engineer of Record must verify the wall design using the forces specifi ed in CBC Section 1632A, using AP=2.5 and RP=3.0 for the forces due to the component, combined with the lateral force of the wall itself, computed using the weight of the wall with AP=1.0 and RP=3.0. Most instrumentation weighs well below the maximum load ratings. It is impractical to attempt to meet specifi c load requirements based on given weights of vari-ous instruments and the potential for changing instruments. Consequently, all installations must meet the maximum load ratings. The design of the wall studs is by the engineer of record. Inspection of the anchorage by OSHPD is required prior to the installation of the mount system.Compliance with these written instructions, beginning on page 5, is required for the installation of the system.

Standard Anchorage - page 7This manual also provides information on mounting Ergotron 9" Vertical Liftin situations that do not require California OSHPD compliance.

5 of 22888-25-003-02 rev.F • 1/04

a1.5"min.

4"min.

a Construct metal stud wall with components shown below.

b Go to "step 1", page 2 to determine ergonomic mounting height, then continue with "step c", below.

c Mount lift chassis to wall as shown below, then proceed to "step 3", page 9.

12 gauge, 1.5" x 4" metal backing - minimum

1"

1"

.76"

.76"

The design of the wall studs is by the engineer of record.

#12-14 fasteners(fi ve per angle bracket)

2"x2"x18 gauge steel angle brackets x 4" long (two per cross member)

24 gauge metal studs - minimum

#12-14 Hilti Kwik Flex fasteners. NOTE: Screws are to be placed in the vertical center of the backing.

OSHPD METHOD ALIGHT GAUGE METAL STUD WALLS

cb

2

6 of 22888-25-003-02 rev.F • 1/04

3x4, #2 Hem Fir, Douglas Fir or better wood blockings

The design of the wall studs is by the engineer of record. OSHPD METHOD BWOOD STUD WALLS

Minimum 2x4 @ 16" on center, #2 Hem Fir, Douglas Fir or better wood studs

Simpson A34 framing angles (four per blocking)

10d x 1-1/2" long nails (eight per framing angle)

#12 wood screws with 2-1/2" penetration in the Ergotron mount-ing bracket. NOTE: Screws are to be placed in thevertical center of the 3x4 backing.

a Construct wood stud wall with components shown below.

b Go to "step 1", page 2 to determine ergonomic mounting height, then continue with "step c", below.

c Mount lift chassis to wall as shown below, then proceed to "step 3", page 9.

ca b2

7 of 22888-25-003-02 rev.F • 1/04

PILOT HOLE4X

12.700

.500

M = MONITOR SCREEN HEIGHT

DIVIDED BY 2

PILOT HOLE

TOUSETHISTEMPLATE:

1.REFERTOTHEMANUAL.

2.MEASURETHEHEIGHTOFONLYTHE

SCREENONYOURMONITOR.

3.DETERMINEERGONOMICALLYCORRECT

VIEWINGHEIGHTBYUSINGEQUATION

ABOVE (ORBELOW).

4.MARKTHEDETERMINEDVALUEFORH,

ONTHEW

ALL.

5.ALIGNMOUNTINGHEIGHTLINETOMARK

ONTHEWALL.USINGALEVEL, LE

VEL

THETEMPLATE, THENTACK INPLACE.

6.CLEARLYMARKTHEPOSITIONSFOR

FOURPILOTHOLES INTOTHEWALL.

7.DRILL THEFOURPILOTHOLES.

OUTLINE OF 9"

VERTICAL LIFT

SYSTEM

MOUNTINGHEIGHTLINE:

(OBTAINEDBYSOLVING

EQUATIONBELOW)

MOUNTINGHEIGHTEQUATION

FORSTANDINGAPPLICATIONS:

67.50[1715

mm] MINUSM=H

M=MONITOR'SSCREENHEIGHT

DIVIDEDBY 2 (SEEPICTORAL)

H=HEIGHTFROMFLOORTO

MOUNTINGHEIGHTLINE (ABOVE)


FORSITTINGAPPLICATIONS:

52.00 [132

1mm] MINUSM=H


DIVIDEDBY 2(SEEPICTORAL)

H=HEIGHTFROMFLOORTO


H

H

PILOT HOLE4X

12.700

.500


DIVIDED BY 2

PILOT HOLE

TOUSETHISTEMPLATE:

1.REFERTOTHEMANUAL.





ABOVE (ORBELOW).


ONTHEW

ALL.



VEL





OUTLINE OF 9"

VERTICAL LIFT

SYSTEM

MOUNTINGHEIGHTLINE:

(OBTAINEDBYSOLVING

EQUATIONBELOW)



67.50[1715

mm] MINUSM=H



H=HEIGHTFROMFLOORTO




52.00 [132

1mm] MINUSM=H



H=HEIGHTFROMFLOORTO


H

H

TOFLO

OR

H"(H mm)

PILOT HOLE4X

12.700

.500


DIVIDED BY 2

PILOT HOLE

TOUSETHISTEMPLATE:

1.REFERTOTHEMANUAL.





ABOVE (ORBELOW).


ONTHEW

ALL.



VEL

THETEMPLATE, THENTACK IN PLACE.




OUTLINE OF 9"

VERTICAL LIFT

SYSTEM

MOUNTINGHEIGHTLINE:

(OBTAINED BYSOLVING

EQUATIONBELOW)



67.50[1715

mm] MINUSM=H



H=HEIGHTFROMFLOORTO




52.00 [132

1mm] MINUSM=H



H=HEIGHTFROMFLOORTO


H

H

PILOT HOLE4X

12.700

.500


DIVIDED BY 2

PILOT HOLE

TOUSETHIS TEMPLATE:

1.REFERTOTHEMANUAL.





ABOVE (ORBELOW).


ONTHEW

ALL.


ON THEWALL.USINGALEVEL, LE

VEL





OUTLINE OF 9"

VERTICAL LIFT

SYSTEM

MOUNTINGHEIGHTLINE:

(OBTAINED BYSOLVING

EQUATIONBELOW)



67.50[1715

mm] MINUSM=H



H=HEIGHTFROMFLOORTO




52.00 [132

1mm] MINUSM=H



H=HEIGHTFROMFLOORTO


H

H

½" (12.8mm)

*NOTE: If mounting with

different hardware than provided, drill

appropriate size holes.

STANDARD ANCHORAGE TO SHEETROCK WALL

b Use level, pencil and provided template to mark ergonomic mounting height.

c Center punch holes for wall anchors.

d Drill anchor holes with 1/2" diameter bit* e Remove template from wall.

a Go to "step 1", page 2 to determine ergonomic mounting height, then return to "step b", below.

WARNING: The Wall Mounted 9" Vertical Lift must be securely attached to your wall. Because wall construction varies widely and your ultimate mounting method is out of Ergotron’s control, it is imperative that you consult with appropriate local engineering, architectural, or construction personnel to ensure that the 9" Vertical Lift is mounted properly to handle applied loads.


8 of 22888-25-003-02 rev.F • 1/04

f g h i

If, after consulting with appropriate local engineering, architectural, or construction personnel it is determined that wall anchor hardware should be used, install as shown:

4x1/4-20 x 1-1/2"

3/32"(2 38mm)

1/8(3 15mm

5/32"(3.97mm)

j Mount lift chassis to wall with four, 1/4-20x1-1/2" screws and 5/32" hex wrench, provided.

STANDARD ANCHORAGE TO SHEETROCK WALLFor applications where compliance to OSHPD is not required.

f Push anchor plate into hole.

g Pull loop back so plate opens fl at against inside surface of wall.

h Push collar into hole.

i Snap off loop.


9 of 22888-25-003-02 rev.F • 1/04

75 mm 100 mm

Identify the hole mounting pattern dimensions on the back of your monitor and follow appropriate instructions on next page. • 75 mm VESA® FDMI™ Standard Hole Mount*

• 100 mm VESA® FDMI™ Standard Hole Mount* • Non-Standard Hole Mount: contact Ergotron*

•

*VESA® (Video Electronics Standard Association) FDMI™ (Flat Display Mounting Interface) Standard Hole Mount

3 Remove spacer

4 Attach monitor bracket

a Lower keyboard bracket.

b Remove cardboard spacer.

a b

X mm

USA 1-800-888-8458Europe +31 20 312.29.39

WARNING: If your monitor uses a screw size which is different than those provided with your Ergotron mounting solution, use the screws provided with the monitor as those provided may damage your monitor.

WARNING: Injury may result if the cardboard spacer is removed without fi rst lowering the keyboard bracket. DO NOT remove the cardboard spacer before lowering the keyboard bracket.


10 of 22888-25-003-02 rev.F • 1/04

Recessed Mount

4xM4x20mm

4x4x

M4x10mm

Flat Mount

4x#8-32 x 3/16"

a Attach 75-100mm adaptor to monitor bracket.

b Attach 75-100mm adaptor/monitor bracket to monitor.

75 mmVESA® FDMI™

100 mmVESA® FDMI™

4xM4x20mm 4x

4xM4x10mm

Recessed MountFlat Mount


11 of 22888-25-003-02 rev.F • 1/04

5 Mount monitor to lift

a b c d

WARNING: The monitor will not be securely attached to the 9" Vertical Lift until the Locking Pin passes through the tab on the Quick Release

Bracket. Do not leave the monitor unsupported until you are certain the Locking Pin is in place.

d

a Lower monitor into position as shown.

b Pull up on locking pin.

c Swing bottom of monitor toward wall.

d Push locking pin down into tab as far as it will go.


12 of 22888-25-003-02 rev.F • 1/04

6 Attach keyboard pivot

7 Attach keyboard tray

20" - 22"(508-559mm)

recommended

4x#8-32 x 5/16"

4x#8-32 x 5/16"


13 of 22888-25-003-02 rev.F • 1/04

a Determine which keyboard features can be utilized while maintaining minimum profi le: Measure and note distance from center of hole mounting pattern to bottom of monitor; compare to diagram below, and proceed to the corresponding "step b".

5mm)

)

A

21

8 Keyboard tray position based on monitor size

b Remove extension from keyboard tray.

A≤8¾"(222.25mm)

B≤7"(177.8mm)

C≤13"(330mm) N/A

DCB

mm)

A

CenterLine ofmounting

holes

Back of MonitorA,B,C,D


14 of 22888-25-003-02 rev.F • 1/04

C D

b Install wrist rest (sold separately):

B

b Adjust keyboard tray extension: loosen screws with hex wrench, slide the extension to desired position, retighten screws.


15 of 22888-25-003-02 rev.F • 1/04

x

x

21

2.1. 3. 4. 5.

Alcohol Prep

Sterile

Alcohol Prep

Sterile

9 Mount keyboard to tray


16 of 22888-25-003-02 rev.F • 1/04

Dimensions

29.38"(746.3 mm)

11.79"(299.6 mm)

Front View

29.38"(746.3 mm)

4.4"(112 mm)

1.46"(37 mm)

1"(25 mm)

7.25"(184 mm)

16.5"(419 mm)

9" min. -12" max.(230 mm - 300 mm)

Side View

9 Keyboard mount (continued)


17 of 22888-25-003-02 rev.F • 1/04

MonitorPivot

±5o

a

After completion of installation steps, evaluate pivot function for your specifi c installation. Ergotron‛s pivot joints are fac-tory set to provide the proper pivot control and moving force for the majority of users. If excessive force is required to adjust your setup, or if your monitor or keyboard do not remain in the desired position, pivot adjustment may be required. Instructions for adjustment of the pivots can be found in the following pages.

1/2"

a Tilt monitor through the entire 10° range.

b If monitor pivot needs adjustment, remove monitor and tighten or loosen as required. NOTE: adjust at each pivot point equally.


18 of 22888-25-003-02 rev.F • 1/04

90°

KeyboardPivot

1/2"

b a Tilt Keyboard Tray, with keyboard attached, through the entire 90° range.

b If Keyboard Tray pivot needs adjustment, tighten or loosen as required.NOTE: adjust at each pivot point equally.


19 of 22888-25-003-02 rev.F • 1/04

Vertical Lift

c a With all components loaded, move monitor and keyboard to highest and lowest positions.

b If adjustment is needed, tighten or loosen as required.


20 of 22888-25-003-02 rev.F • 1/04

a Remove monitor.

b Attach front cover.

10 Attach covers and cable clips

2x

#8-32 x 3/8"

10x

#8-32 x 3/16"

2x 2x

c Attach cable clips and side covers. NOTE: The four cable clips can be attached at any of the holes located along the top, bottom and sides of the lift chassis using the same screws that secure the side covers. Re-attach monitor after front and side covers are attached.

a

b

c


21 of 22888-25-003-02 rev.F • 1/04

NOTE:Leave enough slack in the cables for unrestrictedmovement.

10x

d

e

f

d Reattach monitor.

e Slide-on keyboard covers.

f Route and organize cables with provided ties.


22 of 22888-25-003-02 rev.F • 1/04

© 2004 Ergotron, Inc. All rights reserved.

Patents Pending and Patented U.S. & Foreign. Ergotron is a registered trademark of Ergotron, Inc. Reproduction of this material in whole or part for any purpose other than that authorized by Ergotron, Inc. is prohibited.

Weight Capacity The combined load capacity of the system (keyboard and monitor) ranges from 5-30 lbs. (2.3 - 13.6 kg).

Monitor Pivot

Keyboard PivotLift Tension

c b

a

? Troubleshooting

Symptom Probable Cause Solution

Monitor and Keyboard drift upward or downward.

Vertical Lift Tension needs adjust-ment.

Monitor tilts too easily or with diffi culty. Monitor Pivot needs adjustment.

Keyboard Tray tilts too easily or with diffi culty. Keyboard Pivot needs adjustment.

Keyboard Tray does not fold up under the monitor.

Keyboard Tray confi guration does not work with your monitor size.

See Keyboard Tray Arrangements in Step 8a, page 13.

Ergotron USA 1-800-383-1916Ergotron Europe +31 20 312.29.39

c

a

b

18

16

17


9' vertical lift with slide-out keyboard tray for flat panel ... cardboard spacer until...

Documents