8mm curved glass door v06-06-2014(30adjustment) · glass breakage claims will not be accepted after...
TRANSCRIPT
FOR OFFSET(EXTENDED) ITEMS,DECIDE WHICH HAND IS
REQUIRED BEFORE INSTALLATION.
V06/06/2014
ASSEMBLY INSTRUCTIONS
8mm CURVED GLASS DOOR
BEFORE YOU START, HERE IS SOME IMPORTANT INFORMATION
1) General Information
2) Addition notes
Please inspect this product upon delivery. any missing parts or manufacturing
defects must be reported immediately to the supplier. Damage of defects reported
later will not be accepted. TAKE CARE WHEN HANDLING GLASS PARTS-AVOID
HEAVY CONTACT BETWEEN THE GLASS EDGES AND ANY HARD SURFACE.
Glass breakage claims will not be accepted after the product has been unpacked.
Please note--alumimium is a soft metal, and undergoes a series of extrusion.
fabrication, polishing and anodising processes in order to create your finished
shower enclosure. Some light surface marks are normal, and is a result of the
manufacturing processes. Quality control has ensured that this item is of a good
standard, and is fit for purpose.
Please read these instructions carefully before starting installation.Special care should be taken when drilling walls to avoid hidden pipes or electrical cables.
Note: this product is heavy and may require two people to install.
TOOLS REQUIRED
This product is heavy and may require two people to install.
Ø3mm Drill bit
Ø6mm Drill bit
Pencil
Spirit level
Tape measure
DESCRIPTION DESCRIPTIONPART IMAGE PART IMAGE
Drill
Flat-headScrewdriver
Cross headScrewdriver
Hammer
Silicone Sealant
1
ASSEMBLY INSTRUCTIONS-DRAWING
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(12)
(13)
(9)
(14)
(10)
(15)
(17)
(18)
(19)
(20)
(21)
(22)
(23)
(24)
(25)
(26)
(27)
(28)
(11)
(16)
2x Vertical Seal(Fixed Panel)
2x Bottom Guide Blocks
2x Vertical Seal (Moving Door)
2x Bottom Seals
1xDrip Strip
2x Moving Doors
2x Screw Cover Caps
2x Screws 4X30 (Round Head)
2x Magnet Seals
2x Handles
2x Cover Caps(Wall Post)
2x Cover Caps(Vertical Profile)
2x Cover Caps(Top Rail)
4x Screws (Sink Head)
2x Washers(Top Rail)
2x Glass Fixing Part A
2x Glass Fixing Part B
1x Guide Rail
3x Door Stops
4x Rollers
4x Safety Knobs
2x Fixed Panels
6x Screw Cover Caps
6x Screws 4x12
6x Screw Cover Cap Washers
8x Screws 4x30 (Pan Head)
2x Wall Posts
8x Wall Plugs
(1)
(2)
(3)
(4)
(5)
(6)(7) (8) (9) (10) (11) (12) (13) (14)
(15)
(16)
(17)
(18)(19)
(20)
(21)
(22)
(23)
(24)(25)(26)(27)(28)
2
3
ASSEMBLY INSTRUCTIONS
If you require help, we advise you firstly contact a competent plumber
Installation Steps
Step 1THESE DIMENSIONS ASSUME THE WALLS ARE PLUMB AND THE SHOWER TRAY IS LEVEL, AND THAT THE WALLS ARE TILED DOWN TO THE TOP OF THE TRAY USING A 10mm TILE/WET WALL PANEL.
15
10
15 15
15
10
900900
216 216
R550
MAKE SURE THE TRAY IS LEVEL, USING A SPIRIT LEVEL, BEFORE INSTALLING THIS
SHOWER PANEL / DOOR.
Step 2
Step 3
x4
x4
x4
x44x30
x4
x4
x4
x4
6mm
4x30
Ø6mm
Take care not to damage wall surface
15
4
x2
x2 x2
x2
x2
Ø3mm
Make sure the glass frame is nowcentral between the wall profiles
Step 4
Step 5
5
Step 6
Step 7
6
A A
x6
x6
x6
x6
Take care not to drill to the glass
Step 8
Step 9
How to adjust the width of the Quad
Minimum 10mm internal overlap required
Glass panel
Glass panel
Vertical profile
Vertical profile
Wall profile
Wall profile
Wall
Wall
Maximum adjustment
Minimum adjustment
7
INSIDE VIEW INSIDE VIEW
Sil icone
Step 10
Step 11
8
Sil icone
Step 13
Step 12
B
A
B
A
9
Silicone (outside edge only) where the vertical profiles meet the wall, and the fixed glass panels meet the tray
Step 14
10
CARE AND MAINTENANCE
COMMITMENT TO QUALITY
1) AFTER CARE INSTRUCTIONS
2) MAINTENANCE
Regularly clean your shower product with warm soapy water
Clean the plastic parts with a cloth and mild detergent. Never
use any abrasive creams, dissolvents, acetone or detergents
and disinfectants that contain chlorine. The supplier acceptsno liability for any type of use of care other than those contained
in these instructions. The supplier reserves the right to introduce
technical changes without notice.
It is our intention that the quality and functions of this productare of the highest standard. If you require help we advise you
firstly contact a competent plumber. However we understand that
this may not always be the case, so should you experience
any problems please contact out customer services quoting
the following:
Product name: 8mm Quad Enclosure
Product code:
Customer help line number:0344 804 48 48
to prevent lime scale build up. Do not use abrasive cleaning
fluids or materials, or strong chemical cleaners as this will
damage the product surface.
QDD8008 QDD9008 OQD1288 OQD1298
11
12
HFLQ888/ R/HFLQ888 HFLQ899/HFLQ899R, KEY6157, SPA6109
The packaging you have received with your product is 100% recyclable.It must be disposed of in a safe and environmentally friendly way.We suggest you take it to the local landfill site and discard in the designated bins.