86201026 dial indicator alignment procedure

7/27/2019 86201026 Dial Indicator Alignment Procedure

http://slidepdf.com/reader/full/86201026-dial-indicator-alignment-procedure 1/4

Dial Indicator Alignment ProcedureThe procedure for doing reverse dial indicator alignment is not a difficult one.There are several steps which need to be taken for a successful alignment job.

Step 1

Familiarize with terms, techniques and procedure.*follow all safety rules and procedures

Step 2Learn about the machine you are aligning.

1. Visually check coupling, pipehangers, base bolts, coupling spacing etc.

2. Check for coupling & shaft run out.

Step 3Know the characteristics of your tool. Perform a Sag Check

• A sag check is a test that determines the amount an indicator bracket willsag at a given distance. • How to perform a sag check:Clamp the brackets on a sturdy piece of pipe the same distance they will be whenplaced on the equipment. Zero both indicators on top, then rotate to the bottom.The difference between the top and bottom reading is the sag.

• Sag will always have a negative value, so when allowing for sag on thevertical move always start the dial indicator with a plus(+) reading. For exampleif you have .002" sag; when you zero your indicators on top put the needle on a

+2 instead of zero to compensate for the sag.Step 4Prepare the machine. a. Remove all existing shims from under the feet

-if old shims are to be used, clean them thoroughly.-always use minimum amount of shims.

b. Clean the base thoroughly.-scrape and file away all rust, nicks, and burrs

c. Examine the base bolts and holes.-retap if necessary-replace bolts if necessary

Step 5

Clean mounting surface, file off nicks and burrs.b. Check indicators for sticking and loose needle.c. Aim indicator stem directly toward center line of shaft.

Step 6Measurement -measure distance between the two indicators.

-measure distance between indicator and front feet.-measure distance between front and back feet.

Step 7Layout graph paper

-mark indicator position-mark feet position.-remember to mark + and - signs (this eliminates confusion)



example: graph layout

Step 8Preliminary Horizontal Move

• The horizontal move is the part of the alignment process that aligns theshaft's centerlines from side to side. View the machine from the pump end, zerothe indicators on the left, and then rotate and read on the right. Make sure thatyou always view the pump from the same direction in order for you to keep theleft and right directions correct. There is no sag compensation on the horizontalmove.

For Example:the indicator on the pump reads -8the indicator on the motor reads +10

The shafts are collinear at 1/2 the Total Indicator Reading.• Using graph paper to illustrate the position. Under the indicator positionmark the point that is 1/2 the indicator reading. (-4 for the pump and +5 for themotor) Connect these points and extend the line past the motors feet. This willshow you how much you need to move the motor for horizontal alignment.

These indicator readings mean that you need to move the motor:front foot .006" leftback foot .007" left

You can avoid graphing the horizontal move by zeroing the indicators on the left androtate them to right. Now turn the indicator needles half way to zero and begin to walkthe motor into place by moving the farthest foot toward zero and then the nearest foot.Slowly walk the motor into place by alternating the moves until you obtain two zeroindicator readings.



Now begin the procedure for the vertical move. Be sure to check your equipment forsag and soft foot.

Step 9Check for Soft FootSoft foot is a condition in which one of the feet does not sit flat on the base. The foot orthe base may have been warped. When you tighten the bolt on the foot, the machinerywill distort.

Parallel Soft Foot Angular Soft Foot How to check for Soft Foot

1. Move indicators to 12 o'clock position, depress indicators and then zero.

2. Loosen one base bolt. If indicator moves away form zero, place theamount of shims that will slide under that foot. Retighten bolt and make sure thedial indicator needle does not move. 3. Repeat this procedure for the remaining feet.

Step 10

Perform Vertical Move

The vertical move is the part of the alignment process that aligns the two shaft'scenterlines into their proper up and down position. Usually you will have to add orremove shims in this step. The indicators are zeroed on the top and read at thebottom. (start with a plus + reading if you need to compensate for sag)Example:

the indicator on the pump reads -12the indicator on the motor reads +8

This means that the shafts are one half the total indicator reading from being collinear atthese points.Using a square grid graph paper to illustrate the position. Under the indicator positionmark the point that is half the indicator reading. ( -6 for pump side indicator and +4 forthe motor side indicator) Connect these two points with a line and then continue theline past the lines representing the feet on the motor. The graph now shows that thefront foot needs to have a .003" shim added and the back foot needs to have a .001"

shim added.



Now with your shims in place. Tighten all bolts and take and check your readings. If the readings are within tolerance than your equipment should be aligned.

Step 11

Tighten all bolts and recheck indicator readings.

Step 12

Remove alignment brackets.

The more you become familiar with these steps the faster you will be able to align yourmachinery

86201026 dial indicator alignment procedure

Documents