80001/e1 texrope ib vsml-group.ru/f/texrope-remni-katalog.pdf · 2020-03-03 · 1 texrope ®...

Industrial Catalogue

E2/80001

1

TEXROPE ® Industrial Catalogue

TEXROPE® is synonymous with a com-plete range of industrial belts includingclassical belts, narrow-section belts,double-V belts, multi-ribbed belts, vari-able-speed drive belts, flat belts andsynchronous belts. This range, whichcomplies with international standards,covers a large variety of applications.

The present catalogue describes the fullTEXROPE® range, and also contains sizelistings. Product description is precededby two practical tools:

• the “selection table - new drives” willhelp you to determine which type ofbelt is best suited to the applicationin mind;

• the “selection table - replacements”enables you to identify the type ofbelt to be replaced even when theoriginal marking is no longerreadable.

2

List of contents

Selection tables

New drives p. 3

Replacements p. 4

V-belts

TEXROPE® S 84 Wrapped classical-section belts p. 6

TEXROPE® VP 2 Wrapped narrow-section belts p. 10

TEXROPE® HFX Raw edge narrow-section belts p. 14

Other belts

TEXROPE® VSX V-ribbed belts p. 16

TEXROPE® VRX Variable-speed drive belts to ISO 1604or with “VNN” non-standard profiles p. 18

TEXROPE® HEXAGO Wrapped double-V belts p. 20

TEXROPE® LM Belts for agricultural machinery p. 21

TEXROPE® MULTI 84 Classical-section banded V-belts p. 22

TEXROPE® MULTI VP 2 Narrow-section banded V-belts p. 23

TEXROPE® COMBITEX™ Flexible link V-belts p. 24

TEXROPE® MA 3 Flat belts with protected edges p. 25

TEXROPE® SPEEDFLEX® Endless flat belts p. 26

Synchronous belts & flexible couplings

TEXROPE® STB Synchronous belts with STBtrapezoidal tooth profile p. 28

TEXROPE® HTD®150 Synchronous belts with improved HTD® profile p. 30

SYNCHROPOWER® Polyurethane belts p. 32

TEXROPE® LL Open-ended synchronous belts withSTB or HTD® tooth profile p. 35

TEXROPE® DF Double-sided synchronous belts withSTB or HTD® tooth profile p. 36

TEXROPE® CFX Flexible couplings p. 38

Tools

TEXROPE® ATX Laser alignment device p. 40

Special constructions, advice, care and maintenance

®: Registered trademark of the Gates Corporation.

List of contents

3

Selection table - new drives

The purpose of this table is to direct the user faced with a drive problem towards the TEXROPE® belt type whichis best suited to the application.

(1) Special cases only

(2) Agricultural machinery

(3) Generally, single belt

(4) Distributed on both sides

(5) Polyurethane belts leave no stains onpaper or other material

(6) Depends on the pulleys, materials andbalancing.

KeyThe indications are relative, and can be interpreted asfollows:

Not a feasible solution or one strongly advisedagainst with this type

* Possible, but not really recommended** Good*** Very good**** Excellent

Criterion not relevant to this type

Selection table - new drives

S 84 VP 2 HFX VSX SPEEDFLEX® VRX LMSynchronisation requiredNew drive * * * * * * * * * (1) (2)Maximum power (kW) 400 500 600 500 300 100 10 (3)Reduced shaft loads * * * * * * * * * * * * *Max. linear velocity (6) 35 m/s 40 m/s 45 m/s 50 m/s 55 m/s 50 m/sSmall diam. possible * * * * * * * * * * * * * * * *Overall dimensions * * * * * * * * * * * * * *Considerable torque variations * * * * * * * * * * * * * * *Friction clutch * * * * * * *Reverse bending * * * * * * * * * * * *Linear displacementSerpentine drive * * *Speed variation * * *Required cleanliness

This table does not replace the technical manuals nor any advice given by your TEXROPE® distributor.

STB HTD®150 SYNCHROPOWER® LL DFSynchronisation required * * * * * * * * * * * * *New drive * * * * * * *Maximum power (kW) 200 400 70 50 (4)Reduced shaft loads * * * * * * * * * * * *Max. linear velocity (6) 60 m/s 60 m/s 75 m/s 60 m/sSmall diam. possibleOverall dimensions * * * * * * * * *Considerable torque variations * * * * * * * * *Friction clutchReverse bending * * * * * * * * * * *Linear displacement * * * * * * * * *Serpentine drive * * * * * * * * * *Speed variationRequired cleanliness * * * * (5)

4

This table enables you, when dealing with an existing drive, to readily identify the belt to be replaced even ifthe marking is illegible or the belt has been partially destroyed. For column four, use Table B "V-belt cross-sections" on the next page.

A - Identification of the belt type- Define the family: flat, toothed, ribbed or V-belt- Verify the type of elastomer: rubber, polyurethane,...

Selection table - replacements

Family

STEPS FLAT FLAT TOOTHED FLAT RIBBED V-BELTS(synchronous)

N° 1 THICKNESS (mm) TOOTH PROFILE NUMBER OF RIBS CROSS-SECTIONCurved, (male) MEASUREMENT (mm)

trapezoidal,... Top widthx height (refer to table)

N° 2 WIDTH (mm) PITCH BETWEEN TEETH PITCH BETWEEN RIBS ANGLE EVALUATION(mm) (mm)

To be taken over 10 teeth Take the maximum width A variable-speed belt for more accuracy. of the ribs and divide by may be concerned.

the number of ribs.

N° 3 INSIDE LENGTH (mm) NUMBER OF TEETH EFFECTIVE LENGTH WRAPPING(mm) (YES/NO?)

To be multiplied by Is measured at the rib bottom.the pitch to obtain NOTCHEDthe pitch length. (YES/NO?)

N° 4 WIDTH (mm) OUTSIDEOR DATUM LENGTHLength conversion as

per catalogue.For measurement

of a datum length: unrollthe belt flat on its back.

PLEASE REFER TO THE TEXROPE® INDUSTRIAL CATALOGUE

EXAMPLE Thickness: 2.2 mm Tooth: trapezoidal No of ribs: 8 Section: 13 x 10Pitch: 5.08 mm Angle: 38°

Width: 40 mm No. of teeth: 60 Pitch: 4.70 mm Raw edge(Lp = 304.8 mm)

Length: 1400 mm Width: 9.53 mm Length: 2705 mm Length: 1400 mm(i.e. 37/100th inch)

␣ CATALOGUE SPEEDFLEX® TEXROPE® STB TEXROPE® VSX TEXROPE® HFX DESIGNATION TYPE 2 - 1400 120 XL 037 2705 L 8 XPA 1400

OF 4 CM


MEASURED LENGTH: if the belt is worn, take elongation during service (except for synchronous belts) intoaccount. Take the next lowest length in the catalogue.

For V-belts Ld = datum length replaces the former Lp = pitch length as per ISO 1081.

5

B - V-belt cross-sections


width x height (mm) narrow section classical section agricultural VRX variable speed

6.0 x 4.0 Y6.4 x 4.1 RMA 2L8.0 x 5.0 DIN 89.7 x 5.6 RMA 3L9.7 x 8.0 XPZ / SPZ / 3V

10.0 x 6.0 Z12.7 x 7.9 RMA 4L12.7 x 10.0 XPA / SPA13.0 x 6.0 VNN13.0 x 8.0 A15.8 x 13.5 5V16.3 x 13.0 XPB / SPB16.8 x 9.7 RMA 5L17.0 x 6.0 W 1617.0 x 11.0 B18.6 x 15.0 DIN 1920.0 x 12.5 DIN 2021.0 x 7.0 W 2022.0 x 8.0 VNN22.0 x 14.0 C22.0 x 18.0 XPC / SPC25.0 x 16.0 DIN 2525.0 x 23.0 8V25.4 x 12.7 HI26.0 x 8.0 W 2528.0 x 8.0 VNN31.8 x 15.1 HJ32.0 x 16.0 AGRI32.0 x 19.0 D33.0 x 10.0 W 31.537.0 x 10.0 VNN38.0 x 25.0 E38.1 x 17.5 HK42.0 x 13.0 W 4044.5 x 19.8 HL47.0 x 13.0 VNN50.8 x 22.2 HM52.0 x 16.0 W 5055.0 x 16.0 VNN57.7 x 24.4 HN60.7 x 25.3 HO65.0 x 20.0 W 6383.0 x 26.0 W 80

104.0 x 32.0 W 100

Cross-sections in bold are available from stock.

All Texrope® antistatic V-belts are in accordance with the antistatic requirements as stated in EN 13463-5 - “Non-electrical equipment intended for use in potentially explosive atmospheres - Part-5: protection by constructural safety”- and can as such be used in the conditions described in the Directive 94/9/EC - ATEX.

6

F F 3F3F

The calculation procedure described in the manual "TEXROPE® V-belt drives" (ref. E2/80002) provides all theinformation needed to calculate a drive system using TEXROPE® S 84 belts.

TEXROPE ® S 84Wrapped classical-section V-belts

The first V-belt introduced on international markets was the classical-sectionwrapped V-belt.

The boom in V-belts owes much to the "wedge effect". For a given statictension, this effect virtually triples a classical V-belt's sidewall contactsurface compared to that of a flat belt - simply as a result of the beltgeometry.Overall grip and power ratings are also tripled at standard speeds.

Overall size is reduced by about 25%.

The big advantage of TEXROPE® S 84 belts lies in the excellent balance betweenthe load-carrying capacity of the tensile member and the drive capacity providedby the grip of the sidewalls.

Construction and features• The MONOCORD tensile member consists of specially treated high-

strength polyester cord to transmit tensile forces and withstandoccasional or recurrent shockloads.

• The fabric jacket provides grip, protection against external agents and resistance to abrasion.• The belt compound converts tensile forces on the sidewalls into longitudinal forces in the tensile member.• The belt has good resistance to mineral oils and temperatures between -30°C and +60°C (+80°C for short

periods).• The belt conforms to standards ISO 4184, DIN 2215, NF T-47 141 and BS 3790.• It meets ISO standard 1813 for static conductivity.• The belts are length-stable and do not need to be matched in sets (except E section belts with code length

system). The symbol confirms their stabilisation.

ApplicationsIn industry, calculations are rarely carried out any more for new drives equipped with classical-section belts.The application of TEXROPE® S 84 belts is mainly in the replacement market.

Physical characteristics

TEXROPE ® S 84

84 B 255 1706475 17 X 6450 LI

WWd

T

Measuring datum circumference

Ld = datum lengthLe = outside lengthLi = inside length

LdLe

Li F

Z A B C D E 25Nom. section W x T (mm) 10 x 6 13 x 8 17 x 11 22 x 14 32 x 19 38 x 25 25 x 16Datum width Wd (mm) 8.50 11 14 19 27 32 21Weight (g/m) 64 108 188 310 590 900 420Min. pulley diameter (mm) 63 71 112 170 300 450 224Le - Ld (mm) 15 16 22 34 51 66 35Ld - Li (mm) 22 30 43 52 75 82 61

7TEXROPE ® S 84

TEXROPE ® S 84

1000425 Z15 1/2 400 4221000435 Z16 415 4351000442 Z17 425 4501000455 Z17 1/4 438 4601000487 Z18 480 5001000505 Z18 3/4 490 5051000515 Z19 500 5151000520 Z19 1/2 505 5201000528 Z20 515 5401000540 Z20 1/2 525 5501000578 Z22 560 5901000584 Z22 1/4 565 5951000615 Z23 3/4 600 6301000621 Z24 608 6351000640 Z25 630 6501000667 Z25 1/2 655 6751000690 Z26 670 6901000714 Z27 700 7251000743 Z28 1/2 725 7501000755 Z29 730 7551000790 Z30 1/2 775 8001000795 Z30 3/4 780 8051000800 Z31 785 8101000838 Z32 820 8451000890 Z34 1/4 870 8901000900 Z34 1/2 875 9001000925 Z36 915 9351000970 Z37 950 9701000990 Z38 1/4 970 9901001000 Z38 1/2 980 10001001010 Z39 990 10101001020 Z40 1000 10201001060 Z41 1050 10701001150 Z44 1125 11521001180 Z46 1165 11851001200 Z47 1180 12001001220 Z47 1/2 1194 12201001238 Z48 1230 12501001250 Z49 1235 12601001275 Z49 1/2 1250 12751001295 Z50 1270 12951001305 Z50 1/2 1285 13051001327 Z51 1300 13271001340 Z52 1320 13501001362 Z53 1346 13621001395 Z54 1371 13951001420 Z55 1400 14201001475 Z57 1450 14751001500 Z58 1475 15001001525 Z59 1500 15251001540 Z59 1/2 1515 15401001550 Z60 1524 15501001580 Z61 1550 15801001600 Z62 1575 16001001625 Z63 1600 16251001650 Z64 1626 16501001675 Z65 1651 16801001700 Z66 1675 17001001725 Z67 1700 17251001750 Z68 1725 17501001775 Z69 1750 17751001800 Z70 1775 18001001825 Z71 1800 18251001850 Z72 1829 18501001875 Z73 1850 18751001925 Z75 1900 19251001950 Z76 1930 19501002000 Z78 1975 20001002025 Z79 2000 2025

1700695 B26 650 6901700745 B28 710 7451700772 B29 745 7851700790 B30 750 7901700825 B31 790 8351700860 B32 825 8601700870 B32 1/4 830 8701700875 B32 1/2 835 8751700900 B34 850 9001700919 B35 889 9301700925 B35 3/4 895 9401700934 B36 900 9501700960 B36 3/4 920 9651700970 B37 925 9701700995 B37 1/2 950 9851701000 B38 965 10101701019 B38 1/2 975 10201701026 B39 1000 10401701065 B40 1030 10651701085 B41 1040 10851701100 B42 1060 11051701130 B42 1/2 1075 11101701145 B43 1100 11451701150 B44 1110 11501701159 B44 1/2 1120 11601701165 B45 1150 11851701200 B46 1175 12101701230 B46 1/2 1190 12301701235 B47 1200 12351701250 B47 1/4 1207 12501701261 B48 1215 12651701270 B48 1/2 1225 12751701280 B49 1250 12901701295 B49 1/2 1275 13181701305 B50 1290 13301701328 B51 1300 13401701365 B52 1320 13651701375 B52 1/2 1350 13901701385 B53 1360 14051701400 B53 1/2 1372 14201701407 B54 1400 14401701428 B55 1410 14501701465 B55 1/2 1422 14651701480 B56 1435 14801701500 B57 1450 15001701520 B58 1473 15201701533 B58 1/2 1485 15331701552 B59 1500 15501701580 B59 1/2 1520 15601701585 B60 1525 15651701595 B61 1550 15951701615 B61 1/2 1575 16151701620 B62 1590 16301701634 B63 1600 16351701670 B64 1625 16701701686 B65 1650 16901701710 B65 1/2 1676 17201701720 B66 1697 17351701740 B66 1/2 1700 17401701745 B67 1707 17451701755 B67 1/4 1715 17551701763 B68 1725 17701701774 B69 1750 17951701800 B69 1/2 1761 18051701813 B70 1775 18201701838 B71 1800 18501701864 B72 1829 18751701885 B73 1850 18951701916 B74 1880 19251701938 B75 1900 1945

Z - 10 x 6Belt code RMA Li Ld

Code mm mm

1300441 A16 425 4551300483 A18 457 4901300505 A19 475 5051300555 A20 525 5551300570 A21 540 5701300595 A22 565 5951300620 A23 590 6201300630 A23 1/2 600 6301300635 A24 610 6401300663 A25 630 6631300675 A25 1/2 650 6801300684 A26 670 7001300716 A27 700 7301300745 A28 710 7451300755 A28 1/2 740 7701300767 A29 750 7801300775 A29 1/2 760 7901300794 A30 767 8001300810 A31 775 8101300825 A31 1/2 800 8251300835 A32 805 8351300838 A32 1/4 825 8551300840 A32 1/2 838 8601300850 A32 3/4 841 8701300857 A33 850 8751300869 A33 1/4 855 8801300900 A34 875 9001300905 A34 1/2 889 9191300912 A35 900 9301300945 A36 914 9451300955 A36 1/2 925 9551300960 A37 950 9751300971 A37 1/4 965 10001300993 A38 975 10101301004 A38 1/2 985 10151301045 A40 1016 10451301055 A40 1/2 1030 10601301060 A41 1041 10701301085 A41 1/2 1060 10951301093 A42 1075 11001301110 A43 1090 11201301120 A43 1/2 1105 11351301130 A44 1120 11451301155 A44 1/2 1130 11601301165 A45 1143 11651301175 A45 1/2 1150 11751301193 A46 1180 12051301220 A47 1200 12201301235 A47 1/2 1210 12351301244 A48 1225 12551301270 A48 1/2 1240 12651301278 A48 3/4 1250 12801301280 A49 1270 12951301310 A50 1280 13101301318 A50 1/2 1290 13181301321 A51 1300 13301301335 A51 1/2 1315 13451301355 A52 1320 13551301360 A52 1/2 1335 13651301385 A53 1350 13851301400 A54 1375 14001301410 A54 1/2 1400 14301301421 A55 1410 14401301447 A56 1422 14551301473 A57 1450 14851301500 A58 1475 15051301515 A59 1500 15251301545 A60 1525 15601301580 A61 1550 15801301610 A62 1575 1610

A - 13 x 8Belt code RMA Li Ld

Code mm mm

A - 13 x 8Belt code RMA Li Ld

Code mm mm

B - 17 x 11Belt code RMA Li Ld␣

Code mm mm

1301620 A62 1/2 1600 16201301625 A63 1615 16451301651 A64 1625 16551301670 A65 1650 16801301710 A66 1676 17061301730 A67 1700 17301301750 A67 1/2 1725 17551301756 A68 1750 17751301785 A69 1760 17901301800 A70 1775 18101301828 A71 1800 18351301854 A72 1825 18601301880 A73 1854 18851301905 A74 1880 19151301931 A75 1900 19401301960 A76 1930 19601301981 A77 1960 19901302003 A78 1980 20101302025 A79 2000 20401302060 A80 2032 20651302085 A81 2060 20901302109 A82 2083 21151302130 A83 2100 21301302140 A83 1/2 2120 21501302150 A84 2134 21651302180 A84 1/2 2150 21801302190 A85 2160 22001302220 A86 2200 22201302235 A87 2215 22451302250 A88 2240 22701302295 A89 2261 22951302315 A90 2286 23201302336 A91 2306 23451302370 A92 2337 23701302387 A93 2360 23951302413 A94 2383 24201302445 A95 2413 24451302470 A96 2438 24751302489 A97 2464 24951302525 A98 2500 25301302565 A100 2540 25701302616 A102 2591 26201302667 A104 2650 26801302699 A105 2680 27101302750 A107 2725 27501302768 A108 2743 27751302819 A110 2800 28301302877 A112 2845 28851302920 A114 2896 29201302950 A115 2921 29501302971 A116 2946 29801303000 A117 2972 30001303022 A118 3000 30301303080 A120 3048 30851303175 A124 3150 31801303283 A128 3250 32901303335 A130 3305 33351303380 A132 3350 33801303436 A134 3404 34361303485 A136 3454 34851303507 A137 3477 35151303580 A140 3550 35801303660 A143 3630 36601303690 A144 3660 36901303713 A145 3685 37131303780 A148 3750 37801303835 A150 3800 38351304038 A158 4000 4045

8

1701960 B76 1920 19751702000 B77 1950 20001702010 B78 1981 20201702040 B79 2000 20401702070 B80 2032 20701702092 B81 2060 21001702120 B82 2083 21301702143 B83 2108 21551702169 B84 2120 21701702197 B85 2160 22051702215 B86 2185 22251702245 B87 2200 22451702270 B88 2240 22801702295 B89 2255 22951702322 B90 2286 23301702340 B91 2300 23501702372 B92 2332 23801702395 B93 2360 24051702423 B94 2395 24351702448 B95 2400 24501702477 B96 2450 24851702500 B97 2465 25101702535 B98 2500 25451702560 B99 2520 25601702575 B100 2540 25851702610 B101 2565 26101702626 B102 2600 26351702640 B103 2615 26551702688 B104 2650 26851702706 B105 2667 27151702726 B106 2700 27501702778 B108 2750 27901702828 B110 2800 28401702884 B112 2845 28901702941 B114 2900 29551702970 B115 2930 29701702981 B116 2950 29901703034 B118 3000 30401703087 B120 3048 30951703150 B122 3107 31501703182 B124 3150 31901703225 B125 3175 32251703250 B126 3210 32501703270 B127 3227 32701703290 B128 3250 33001703337 B130 3297 33501703370 B131 3327 33701703387 B132 3350 33951703420 B133 3390 34301703455 B134 3415 34651703504 B136 3450 35001703535 B137 3505 35351703550 B138 3507 35501703582 B139 3550 35901703644 B142 3600 36441703698 B144 3658 37051703744 B146 3700 37441703774 B147 3750 37801703896 B151 3850 38901703905 B152 3861 39051703955 B154 3912 39551703990 B156 3962 40101704052 B158 4000 40601704150 B162 4115 41601704225 B165 4200 42401704277 B167 4250 42951704432 B173 4394 44401704500 B175 4450 45001704530 B177 4500 45451704612 B180 4572 4620

1704670 B182 4625 46701704733 B185 4699 47401704770 B186 4725 47701704784 B187 4750 47951704930 B192 4880 49301704945 B193 4902 49451704992 B195 4953 50001705038 B197 5000 50451705350 B208 5300 53501705370 B210 5334 53801705640 B220 5600 56401705698 B223 5665 57051706044 B236 6000 60441706098 B240 6065 61051706332 B248 6300 63401706440 B253 6400 64401706475 B255 6450 64851706544 B256 6500 65441706600 B259 6550 66001706740 B264 6700 67451706858 B270 6825 68651706945 B273 6900 69451707044 B276 7000 70441707132 B280 7100 71401707618 B300 7585 76251708010 B315 7970 80101709160 B360 9120 9160

2201130 C41 1/2 1070 11202201150 C43 1090 11502201215 C45 1/2 1180 12352201225 C46 1200 12502201285 C48 1235 12852201310 C50 1260 13102201341 C51 1295 13502201370 C51 1/2 1320 13702201395 C52 1350 13952201430 C53 1375 14302201441 C55 1410 14602201485 C56 1435 14852201510 C57 1460 15102201550 C58 1500 15502201565 C60 1535 15852201625 C61 1574 16252201650 C62 1600 16502201665 C63 1625 16752201700 C64 1650 17002201705 C65 1676 17252201750 C66 1700 17502201776 C68 1750 18002201820 C69 1778 18362201830 C70 1800 18502201847 C70 1/2 1815 18652201881 C72 1842 19002201910 C73 1/2 1880 19352201951 C75 1930 19702202000 C76 1956 20002202030 C77 1981 20302202050 C78 2000 20502202076 C79 1/2 2032 20902202105 C81 2083 21252202145 C82 2100 21652202180 C83 2120 21802202200 C84 2159 22002202210 C85 2184 22302202279 C87 1/2 2240 23002202305 C89 2286 23302202335 C90 2311 23552202385 C91 2337 23852202406 C92 1/2 2375 24252202435 C93 2388 24352202475 C94 2413 24752202480 C95 2438 24902202490 C96 2450 25102202508 C97 2464 25252202550 C97 1/2 2500 25502202560 C98 2510 25602202575 C99 2540 25952202615 C100 2560 26152202635 C101 2591 26452202660 C102 2605 26602202675 C103 2616 26752202698 C104 2667 27152202719 C105 2685 27352202735 C106 2692 27502202805 C107 2750 28052202820 C108 2762 28202202838 C110 2800 28602202890 C111 2840 28902202897 C112 2870 29152202955 C113 2896 29552202975 C114 2921 29752202985 C115 2950 29902203000 C116 2965 30202203041 C118 3000 30602203100 C120 3068 31202203185 C122 3135 31852203195 C124 3175 3215

2203300 C127 3250 33002203303 C128 3268 33202203346 C129 3302 33552203370 C130 3325 33702203385 C131 3350 33952203397 C132 3373 34252203448 C134 3404 34602203515 C136 3477 35352203600 C140 3550 36152203655 C141 3597 36552203700 C143 3658 37102203711 C144 3678 37302203742 C145 3700 37602203803 C147 3750 38102203830 C148 3772 38302203915 C151 3861 39152203940 C153 3912 39602204045 C157 4000 40652204120 C159 4064 41202204163 C162 4122 41802204270 C165 4212 42702204320 C167 4267 43202204400 C170 4350 44002204445 C173 4413 44652204540 C177 4500 45652204625 C180 4587 46452204794 C187 4750 48102204880 C189 4826 48802205005 C195 4967 50252205048 C196 5000 50552205080 C197 5025 50802205226 C203 5182 52352205250 C204 5200 52502205353 C208 5300 53602205400 C210 5340 54002205410 C211 5372 54302205540 C216 5500 55402205645 C220 5600 56652205710 C223 5690 57302205780 C225 5715 57802205845 C228 5800 58452206044 C236 6000 60602206101 C240 6062 61202206300 C247 6250 63002206345 C248 6300 63652206390 C250 6340 63902206480 C255 6450 65002206744 C265 6700 67602206861 C270 6822 68802207030 C276 7000 70302207145 C280 7100 71652207250 C285 7248 73002207544 C297 7500 75602207621 C300 7582 76402207735 C303 7685 77352207885 C309 7835 78852208045 C314 8000 80652208381 C330 8342 84002208544 C335 8500 85602208765 C345 8730 87802209146 C360 9107 91652210045 C394 10000 100652210670 C420 10632 106902211245 C440 11200 112652212320 C484 12270 12320

B - 17 x 11Belt code RMA Li Ld

Code mm mm

B - 17 x 11Belt code RMA Li Ld

Code mm mm

C - 22 x 14Belt code RMA Li Ld

Code mm mm

C - 22 x 14Belt code RMA Li Ld

Code mm mm

TEXROPE ® S 84

TEXROPE ® S 84

9

3202075 D79 2000 20753202354 D90 2300 23703202430 D93 2360 24303202500 D96 2425 25003202575 D98 2500 25753202720 D104 2650 27203202858 D110 2800 28753203040 D116 2965 30253203075 D118 3000 30753203118 D120 3048 31353203213 D124 3150 32303203275 D126 3200 32753203321 D128 3251 33353203413 D132 3350 34253203533 D137 3475 35503203616 D140 3550 36253203710 D143 3658 37253203729 D144 3670 37453203819 D148 3750 38253204000 D154 3915 40003204063 D158 4000 40803204181 D162 4125 42003204302 D167 4250 43253204370 D170 4310 43853204463 D173 4394 44803204560 D177 4500 45753204643 D180 4572 46603204810 D187 4750 48253204960 D192 4875 49603205023 D195 4953 50403205330 D207 5270 53453205375 D208 5300 53753205420 D210 5350 54353205663 D220 5600 56803205726 D223 5670 57403205795 D225 5715 57953206000 D233 5925 60003206075 D236 6000 60753206103 D240 6045 61203206300 D248 6245 63203206363 D250 6300 63803206475 D255 6415 64903206766 D266 6700 67753206863 D270 6805 68803207163 D280 7100 71803207245 D287 7239 73153207623 D300 7565 76403208063 D317 8000 80803208383 D330 8325 84003208569 D335 8500 85753208765 D345 8700 87803209148 D360 9090 91653209560 D374 9500 95753209950 D390 9880 99503210063 D394 10000 100803210673 D420 10615 106903211263 D443 11200 112803212193 D480 12135 122103212557 D494 12500 125753213718 D540 13660 137353215243 D600 15185 15260

3803085 E117 3000 30853804080 E157 4000 41053804660 E180 4600 46853805040 E195 5000 50653805430 E210 5375 54553805680 E220 5600 57053806102 E240 6050 61253806380 E248 6300 64053806862 E270 6800 68903807180 E280 7100 72053807622 E300 7550 76503708080 E315 8000 81053808382 E330 8350 84103809147 E360 9100 91753810080 E394 10000 101053810672 E420 10600 107003811280 E440 11200 113053812192 E480 12150 122203813717 E540 13650 137453815242 E600 15200 15270

2501600 1600 16602501670 1670 17302501800 1800 18602501900 1900 19602501950 1950 20102502000 2000 20602502050 2050 21102502120 2120 21802502200 2200 22602502240 2240 23002502325 2325 23852502360 2360 24202502450 2450 25102502500 2500 25602502650 2650 27102502700 2700 27602502800 2800 28602502950 2950 30102503000 3000 30602503150 3150 32102503350 3350 34102503550 3550 36102503750 3750 38102503950 3950 40102504000 4000 4060

D - 32 x 19Belt code RMA Li Ld

Code mm mm

E - 38 x 25Belt code RMA Li Ld

Code mm mm

25 - 25 x 16Belt code Li Ld

mm mm mm

TEXROPE ® S 84

TEXROPE ® S 84

Longer lengths in B, C and Dsections are available on request.Dimensions in bold are availablefrom stock.

10

ApplicationsHigh performance of the tensile member, balance and sidewall height: the TEXROPE® VP 2 wrapped narrow-section belt is capable of transmitting more power, other circumstances being equal. This means reduced drivesize and costs.

TEXROPE ® VP 2

TEXROPE ® VP 2Wrapped narrow-section V-belts

The TEXROPE® VP 2 belt has a deeper cross-section than the classical-section belt, but uses the same top width. The increased height of itssidewalls ensures excellent grip and thus, greater power ratings. Theincreased power capacity is also due to the special strength of the tensilemember. The belt can operate at higher linear speeds.The TEXROPE® VP 2 narrow-section belt allows the design of more compactdrives.

Construction and features• The MONOCORD tensile member consists of specially treated high-

strength polyester cord to transmit tensile forces and withstandoccasional or recurrent shockloads.

• The fabric cover provides grip, protection against external agentsand resistance to abrasion.

• The belt compound converts tensile forces on the sidewalls intolongitudinal forces in the tensile member.

• The belt has good resistance to mineral oils and temperatures be-tween -30°C and +60°C (+80°C for short periods).

• The belt conforms to international standards ISO 4184, DIN 7753(geometry), NF T-47 141 and BS 3790.

• It meets ISO standard 1813 for static conductivity.• The belts are length-stable and do not need to be measured for

installation in sets. The symbol confirms their stabilisation.

VP 2 1500 SPZ

Power rating (at 1450 rpm)

Physical characteristicsWWr

T


Ld = datum lengthLe = outside length

SPZ SPA SPB SPC 19Nom. section W x T (mm) 9.7 x 8 12.7 x 10 16.3 x 13 22 x 18 18.6 x 15Datum width Wd (mm) 8.50 11 14 19 16Weight (g/m) 68 120 194 375 270Min. pulley diameter (mm) 71 90 140 200 180Le - Ld (mm) 13 18 22 30 25

LdLe

F

Wd

Puissance (kW)

16

10

7

5

140 160 180 Ø mm

7,4

10,4 SPB

B

11TEXROPE ® VP 2

TEXROPE ® VP 2

The TEXROPE® VP 2 narrow-section belt is available also in 3V and 5V sections defined by standardsRMA/MTPA IP 22 and ASAE S 211.5. All the belts have the qualities of classical-section belts, including lengthstabilisation. They are particularly suitable for equipment designed to American standards. They also conformto ISO standard 1813 for anti-static requirements.The belt designation contains the section code 3V or 5V followed by the length code. The latter is a rounding-off of the effective length measured in 1/10 inch.

3V 5VNom. section bp x hb (mm) 9.65 x 7.8 15.8 x 13.5Datum width Wd (mm) 8.5 14Weight (g/m) 68 194Min. pulley diameter (mm) 67.3 180Leff - Ld (mm) to RMA 3.6 11.3

The calculation procedure described in the manual "TEXROPE® V-belt drives" (ref. E2/80002) provides all theinformation needed to calculate a drive system using TEXROPE® VP 2 belts.



Ld = datum lengthLeff = effective length

bpWr

hb

LdLeff

F

Wd

12

SPZ 500SPZ 512SPZ 515SPZ 530SPZ 545SPZ 560SPZ 562SPZ 580SPZ 600SPZ 612SPZ 615SPZ 630SPZ 637SPZ 650SPZ 662SPZ 670SPZ 687SPZ 690SPZ 697SPZ 710SPZ 717SPZ 722SPZ 730SPZ 737SPZ 750SPZ 758SPZ 762SPZ 772SPZ 775SPZ 787SPZ 800SPZ 812SPZ 825SPZ 837SPZ 850SPZ 862SPZ 875SPZ 887SPZ 900SPZ 912SPZ 922SPZ 925SPZ 937SPZ 950SPZ 962SPZ 975SPZ 987SPZ 1000SPZ 1012SPZ 1024SPZ 1030SPZ 1037SPZ 1047SPZ 1060SPZ 1077SPZ 1087SPZ 1090SPZ 1112SPZ 1120SPZ 1127SPZ 1137SPZ 1150SPZ 1162SPZ 1171SPZ 1180SPZ 1187SPZ 1202SPZ 1212SPZ 1220SPZ 1237SPZ 1250

SPZBelt code Ld

Datum length (mm) (mm)

SPZBelt code Ld


SPABelt code Ld


SPABelt code Ld


TEXROPE ® VP 2

SPZ 1262SPZ 1280SPZ 1287SPZ 1312SPZ 1320SPZ 1327SPZ 1337SPZ 1347SPZ 1360SPZ 1362SPZ 1387SPZ 1400SPZ 1412SPZ 1437SPZ 1450SPZ 1462SPZ 1487SPZ 1500SPZ 1512SPZ 1537SPZ 1550SPZ 1562SPZ 1587SPZ 1600SPZ 1612SPZ 1637SPZ 1650SPZ 1662SPZ 1687SPZ 1700SPZ 1737SPZ 1750SPZ 1762SPZ 1787SPZ 1800SPZ 1812SPZ 1837SPZ 1850SPZ 1862SPZ 1887SPZ 1900SPZ 1937SPZ 1950SPZ 1987SPZ 2000SPZ 2037SPZ 2060SPZ 2120SPZ 2137SPZ 2180SPZ 2187SPZ 2240SPZ 2287SPZ 2300SPZ 2360SPZ 2430SPZ 2500SPZ 2580SPZ 2650SPZ 2720SPZ 2800SPZ 2900SPZ 3000SPZ 3070SPZ 3150SPZ 3250SPZ 3350SPZ 3450SPZ 3550

SPA 750SPA 757SPA 775SPA 782SPA 800SPA 807SPA 825SPA 832SPA 850SPA 857SPA 875SPA 882SPA 900SPA 907SPA 925SPA 932SPA 950SPA 957SPA 975SPA 982SPA 1000SPA 1007SPA 1030SPA 1032SPA 1060SPA 1082SPA 1090SPA 1107SPA 1120SPA 1132SPA 1150SPA 1157SPA 1180SPA 1207SPA 1220SPA 1232SPA 1250SPA 1257SPA 1272SPA 1280SPA 1282SPA 1307SPA 1320SPA 1332SPA 1357SPA 1360SPA 1382SPA 1400SPA 1407SPA 1425SPA 1432SPA 1450SPA 1457SPA 1482SPA 1500SPA 1507SPA 1532SPA 1550SPA 1557SPA 1582SPA 1600SPA 1607SPA 1632SPA 1650SPA 1657SPA 1682SPA 1700SPA 1707SPA 1732SPA 1750SPA 1757SPA 1782

SPA 1800SPA 1807SPA 1832SPA 1850SPA 1857SPA 1882SPA 1900SPA 1907SPA 1925SPA 1932SPA 1950SPA 1957SPA 1982SPA 2000SPA 2032SPA 2057SPA 2060SPA 2082SPA 2120SPA 2132SPA 2180SPA 2182SPA 2207SPA 2227SPA 2232SPA 2240SPA 2282SPA 2300SPA 2307SPA 2332SPA 2360SPA 2382SPA 2430SPA 2432SPA 2475SPA 2482SPA 2500SPA 2532SPA 2580SPA 2582SPA 2607SPA 2632SPA 2650SPA 2682SPA 2720SPA 2732SPA 2782SPA 2800SPA 2832SPA 2882SPA 2900SPA 2932SPA 2982SPA 3000SPA 3032SPA 3070SPA 3082SPA 3150SPA 3182SPA 3250SPA 3282SPA 3350SPA 3382SPA 3450SPA 3550SPA 3650SPA 3750SPA 3870SPA 4000SPA 4250SPA 4500

TEXROPE ® VP 2

500512515530545560562580600612615630637650662670687690697710717722730737750758762772775787800812825837850862875887900912922925937950962975987

100010121024103010371047106010771087109011121120112711371150116211711180118712021212122012371250

126212801287131213201327133713471360136213871400141214371450146214871500151215371550156215871600161216371650166216871700173717501762178718001812183718501862188719001937195019872000203720602120213721802187224022872300236024302500258026502720280029003000307031503250335034503550

750757775782800807825832850857875882900907925932950957975982

1000100710301032106010821090110711201132115011571180120712201232125012571272128012821307132013321357136013821400140714251432145014571482150015071532155015571582160016071632165016571682170017071732175017571782

18001807183218501857188219001907192519321950195719822000203220572060208221202132218021822207222722322240228223002307233223602382243024322475248225002532258025822607263226502682272027322782280028322882290029322982300030323070308231503182325032823350338234503550365037503870400042504500

13

Dimensions in bold are available from stock.Superior lengths in SPB and SPC sections are available on request.

5VBelt code Le = OutsideRMA Code length (mm)

SPBBelt code Ld


SPCBelt code Ld


19Belt code Le

(mm)

3VBelt code Le = OutsideRMA Code length (mm)

TEXROPE ® VP 2

SPB 1250SPB 1280SPB 1320SPB 1360SPB 1400SPB 1450SPB 1500SPB 1550SPB 1600SPB 1650SPB 1700SPB 1750SPB 1800SPB 1850SPB 1900SPB 1950SPB 2000SPB 2060SPB 2120SPB 2180SPB 2240SPB 2300SPB 2360SPB 2430SPB 2500SPB 2530SPB 2580SPB 2650SPB 2720SPB 2800SPB 2840SPB 2850SPB 2900SPB 3000SPB 3070SPB 3150SPB 3250SPB 3350SPB 3450SPB 3550SPB 3650SPB 3750SPB 3870SPB 4000SPB 4120SPB 4250SPB 4370SPB 4500SPB 4620SPB 4750SPB 4870SPB 5000SPB 5300SPB 5600SPB 6000SPB 6300SPB 6700SPB 7100SPB 7500SPB 8000

SPC 2000SPC 2120SPC 2240SPC 2360SPC 2500SPC 2650SPC 2800SPC 3000SPC 3150SPC 3350SPC 3460SPC 3550SPC 3750SPC 4000SPC 4250SPC 4500SPC 4750SPC 5000SPC 5300SPC 5600SPC 6000SPC 6300SPC 6700SPC 7100SPC 7500SPC 8000SPC 8500SPC 9000SPC 9500SPC 10000SPC 10600SPC 11200SPC 11800SPC 12500

1901475 15001901600 16251901675 17001901700 17251901775 18001901800 18251901875 19001901900 19251902000 20251902075 21001902120 21451902175 22001902275 23001902360 23851902375 24001902475 25001902500 25251902575 26001902625 26501902675 27001902800 28251902875 29001903000 30251903075 31001903150 31751903175 32001903550 35751903750 3775

TEXROPE ® VP 2

5V 500 12725V 530 13525V 560 14225V 600 15225V 630 16025V 670 17025V 710 18075V 750 19075V 800 20225V 850 21625V 900 22875V 950 24175V 1000 25525V 1060 26925V 1120 28475V 1180 29975V 1250 31725V 1320 33725V 1400 35725V 1500 38125V 1600 40675V 1700 43225V 1800 45725V 1900 48225V 2000 50925V 2120 53825V 2240 56925V 2360 59925V 2500 63525V 2650 67225V 2800 71225V 3000 76225V 3150 80225V 3350 85225V 3550 9022

3V 250 6413V 265 6733V 280 7013V 300 7613V 315 8003V 335 8473V 355 8993V 375 9613V 400 10223V 425 10853V 450 11423V 475 12103V 500 12703V 530 13493V 560 14103V 600 15233V 630 16093V 670 17093V 710 18083V 750 19083V 800 20283V 850 21503V 900 23003V 950 24133V 1000 25383V 1060 26883V 1120 28433V 1180 30133V 1250 31733V 1320 33633V 1400 3563

125012801320136014001450150015501600165017001750180018501900195020002060212021802240230023602430250025302580265027202800284028502900300030703150325033503450355036503750387040004120425043704500462047504870500053005600600063006700710075008000

20002120224023602500265028003000315033503460355037504000425045004750500053005600600063006700710075008000850090009500

1000010600112001180012500

14

Construction and features

• Top fabric.• High-strength specially treated tensile cords.• Compound reinforced with anti-abrasion fibres.• Optimised moulded notches, ensuring excellent flexibility.• Significant reduction of bending stresses.• Good resistance to mineral oils and to temperatures between -30°C

and +60°C (+80°C for short periods).• Conforms to standards DIN 7753, NF T-47 141 and

BS 3790.• Meets ISO standard 1813 for static conductivity.• All belts are length-stable (not marked with code length system).

Raw edge narrow-section V-belts combine maximum transverse rigiditywith excellent longitudinal flexibility.Today, TEXROPE® HFX, or "high flexibility belts" give even better perfor-mance. The new notch profile reduces bending stresses while flexingaround pulleys, enabling the use of pulleys smaller than those used forother raw edge belts. This means that more compact, and hence moreeconomical drives can be designed, and much greater speed ratiosachieved. On traditional diameter pulleys, the reduction in bending stresseshas the effect of increasing belt life. The TEXROPE® HFX belt is the firstchoice for narrow-section belt drives.

TEXROPE ® HFXRaw edge narrow-section V-belts

TEXROPE ® HFX

HFX 1500 XPA

ApplicationsThe significant power rating increase and the use of small-diameter pulleys are decisive for the drive design.Investment costs can be optimised substantially. The anti-wear properties and the cooling effect provided by thenotching result in increased belt life and reduced maintenance costs.


The calculation procedure described in the manual "TEXROPE® V-belt drives" (ref. E2/80002) provides all theinformation needed to calculate a drive system using TEXROPE® HFX belts.

XPZ XPA XPB XPCNominal section W x T (mm) 10 x 8 13 x 10 16.3 x 13 23 x 18Datum width Wd (mm) 8.5 11 14 19Weight (g/m) 69 123 195 334Min. pulley diameter (mm) 50 63 90 140Le - Ld (mm) 13 18 22 30

WWd

T

Ld Le

F


Ld = datum lengthLe = outside length

Wd

Power rating (at 1450 rpm)

Power (kW)

min. pulley diameter (mm)

7.8 kW

11 kW

Ø 1

60 m

m

XPB

SPB

B

90 112 140

100 132 140 150 160 180 Ø mm2

16141210

8

6

4

3

15

XPA 732XPA 750XPA 757XPA 775XPA 782XPA 800XPA 825XPA 832XPA 850XPA 857XPA 875XPA 882XPA 900XPA 907XPA 925XPA 932XPA 950XPA 957XPA 975XPA 982XPA 1000XPA 1007XPA 1030XPA 1060XPA 1082XPA 1090XPA 1107XPA 1120XPA 1132XPA 1142XPA 1150XPA 1157XPA 1172XPA 1180XPA 1207XPA 1220XPA 1232XPA 1250XPA 1257XPA 1272

TEXROPE ® HFX

TEXROPE ® HFX

XPZ 600XPZ 630XPZ 660XPZ 670XPZ 687XPZ 710XPZ 722XPZ 737XPZ 750XPZ 762XPZ 775XPZ 787XPZ 800XPZ 817XPZ 825XPZ 837XPZ 850XPZ 862XPZ 875XPZ 887XPZ 900XPZ 917XPZ 925XPZ 937XPZ 950XPZ 962XPZ 975XPZ 987XPZ 1000XPZ 1012XPZ 1030XPZ 1037XPZ 1060XPZ 1080XPZ 1087XPZ 1110XPZ 1120XPZ 1137XPZ 1150XPZ 1162XPZ 1180XPZ 1212XPZ 1220XPZ 1237XPZ 1250XPZ 1280XPZ 1287XPZ 1320XPZ 1337XPZ 1360XPZ 1400XPZ 1412XPZ 1437XPZ 1450XPZ 1487XPZ 1500XPZ 1537XPZ 1550XPZ 1587XPZ 1600XPZ 1650

XPB 1000XPB 1060XPB 1120XPB 1180XPB 1250XPB 1320XPB 1400XPB 1500XPB 1600XPB 1700XPB 1800XPB 1900XPB 2000XPB 2120XPB 2240XPB 2360XPB 2500XPB 2650XPB 2800XPB 3000XPB 3150XPB 3350XPB 3550XPB 3750XPB 4000XPB 4250XPB 4500XPB 4750

XPZBelt code

Datum length (mm)

XPZBelt code

Datum length (mm)

XPABelt code

Datum length (mm)

XPBBelt code

Datum length (mm)

XPC 2000XPC 2120XPC 2240XPC 2360XPC 2500XPC 2650XPC 2800XPC 3000XPC 3150XPC 3350XPC 3550XPC 3750XPC 4000XPC 4250XPC 4500XPC 4750

XPCBelt code

Datum length (mm)

XPA 1282XPA 1307XPA 1320XPA 1332XPA 1360XPA 1382XPA 1400XPA 1442XPA 1450XPA 1462XPA 1482XPA 1500XPA 1507XPA 1522XPA 1532XPA 1550XPA 1557XPA 1582XPA 1600XPA 1607XPA 1632XPA 1650XPA 1682XPA 1700XPA 1732XPA 1750XPA 1782XPA 1800XPA 1850XPA 1900XPA 1950XPA 2000XPA 2060XPA 2120XPA 2180XPA 2240XPA 2360XPA 2500XPA 2650XPA 2800XPA 3000XPA 3150XPA 3350XPA 3550XPA 3750XPA 4000

XPZ 1700XPZ 1750XPZ 1800XPZ 1850XPZ 1900XPZ 1950XPZ 2000XPZ 2120XPZ 2240XPZ 2360XPZ 2500XPZ 2650XPZ 2800XPZ 3000XPZ 3150XPZ 3350XPZ 3550

XPABelt code

Datum length (mm)

Dimensions in bold are available from stock.

16

TEXROPE ® VSXV-ribbed belts

TEXROPE ® VSX

The TEXROPE® VSX belt combines the high flexibility and light weight offlat belts with the grip of V-belts thanks to the high power ratings createdby the special rib profile.

VSX 1222 J

Construction and features• The top layer is fabric-reinforced resisting reverse bending and

possible wear caused by a back idler.• The specially treated high-strength tensile member withstands the

stresses with reduced and stable elongation.• The longitudinally ribbed high-grip elastomer base offers a large contact surface.• Good resistance to mineral oils and temperatures between -30°C and +60°C (+80°C for short periods).• Suitable for PH, PJ, PK, PL and PM pulley profiles as specified in DIN 7867 and ISO 9982; suitable for H, J,

K, L and M pulley profiles as specified in RMA IP-26 and ASAE S 211.5 standards.• Meets ISO standard 9982.• Meets ISO standard 1813 for static conductivity.

ApplicationsFor a given application, the belt is cut to the required number of ribs thus perfectly matching the requiredpower rating. This makes it possible to obtain a unique, customised belt with the optimum overall size.Vibrations are reduced and there is no need for the matching of sets. These are the key qualities of theTEXROPE® VSX belt.

h

e


The belt code refers to the effective length in mm measured at the top of the pulleys, i.e. at the root of the beltribs.

The calculation procedure described in the manual "TEXROPE® V-ribbed belt drives" provides all the informa-tion needed to calculate a drive system using TEXROPE® VSX belts. Only available in French.

H J K L MCentre distance e (mm) 1.60 2.34 3.56 4.70 9.40Height h (mm) 3.0 3.5 6.0 9.5 16.5Weight per rib (g/m) 5.9 8.4 20 30.9 124.1Min. pulley diameter (mm) 13 20 40 75 180Min. reverse bend diameter (mm) 32 45 70 140 300

Power (kW)

1.75

1.25

1.00

Width

17

PJ356 14.00PJ381 15.00PJ406 16.00PJ432 17.00PJ457 18.00PJ483 19.00PJ508 20.00PJ559 22.00PJ584 23.00PJ610 24.00PJ660 26.00PJ711 28.00PJ723 28.50PJ737 29.00PJ762 30.00PJ813 32.00PJ838 33.00PJ864 34.00PJ914 36.00PJ955 37.60PJ965 38.00

PJ1016 40.00PJ1041 41.00PJ1067 42.00PJ1092 43.00PJ1105 43.50PJ1110 43.70PJ1118 44.00PJ1123 44.20PJ1130 44.50PJ1136 44.70PJ1150 45.30PJ1168 46.00PJ1194 47.00PJ1200 47.30PJ1222 48.00PJ1233 48.50PJ1244 49.00PJ1262 49.70PJ1270 50.00PJ1280 50.40PJ1300 51.20PJ1309 51.50PJ1321 52.00PJ1333 52.50PJ1355 53.40PJ1371 54.00PJ1397 55.00PJ1428 56.20PJ1439 56.70PJ1473 58.00PJ1549 61.00PJ1600 63.00PJ1651 65.00PJ1663 65.50PJ1752 69.00PJ1854 73.00PJ1895 74.60PJ1910 75.20PJ1930 76.00PJ1956 77.00

TEXROPE ® VSX

TEXROPE ® VSX

JBelt code Length

(length mm) inches

JBelt code Length

(length mm) inches

MBelt code Length

(length mm) inches

PM2286 90.00PM2388 94.00PM2515 99.00PM2693 106.00PM2832 111.50PM2921 115.00PM3010 118.50PM3124 123.00PM3327 131.00PM3531 139.00PM3734 147.00PM4089 161.00PM4191 165.00PM4470 176.00PM4648 183.00PM5029 198.00PM5410 213.00PM6121 241.00PM6502 256.00PM6883 271.00PM7646 301.00PM8408 331.00PM9169 361.00PM9931 391.00

Dimensions in bold are availablefrom stock.TEXROPE® VSX H and K sectionsare available on request.

LBelt code Length

(length mm) inches

PL954 37.50PL991 39.00

PL1075 42.30PL1270 50.00PL1333 52.50PL1371 54.00PL1397 55.00PL1422 56.00PL1562 61.50PL1613 63.50PL1664 65.50PL1715 67.50PL1765 69.50PL1803 71.00PL1842 72.50PL1943 76.50PL1981 78.00PL2019 79.50PL2070 81.50PL2096 82.50PL2134 84.00PL2197 86.50PL2235 88.00PL2324 91.50PL2362 93.00PL2477 97.50PL2515 99.00PL2705 106.50PL2743 108.00PL2845 112.00PL2895 114.00PL2921 115.00PL2997 118.00PL3086 121.50PL3124 123.00PL3289 129.50PL3327 131.00PL3493 137.50PL3696 145.50

PJ1981 78.00PJ1992 78.40PJ2083 82.00PJ2210 87.00PJ2337 92.00PJ2489 98.00

18

The performance levels of a variable-speed drive depend very much on thequality of the belt. TEXROPE® VRX belts optimise all drive characteristics:the power or torque achieved at each speed, uniform operation, reducednoise, easier maintenance, etc...TEXROPE® offers two ranges of variable-speed belts:- a range which meets international standard ISO 1604 (section W 16 to

W 100) "Vari-Phi TEXROPE".- a range of non-standard "VNN"

belts, specific to certain Europeanvariable-speed drives.

ApplicationsAll these characteristics, together with a longer belt life, enable variable-speed belts to achieve optimumperformances whether on simple symmetrical variable-speed pulleys, variable-speed units or units with integralgear reducers.

TEXROPE ® VRXVariable-speed drive belts to ISO 1604Variable-speed drive belts with "VNN" non-standard profiles

TEXROPE ® VRX

Vari-Phi TEXROPE® standard variable-speed beltsDeveloped in partnership with Brook Hansen, a specialist in mechanical variable-speed drives, the Vari-PhiTEXROPE® "W"-section variable-speed belts embody an entirely new design which enables them to run excel-lently over reduced-diameter pulleys, while maintaining high transverse rigidity.

Construction and features• The belt consists of heavy fabric cover, a high-strength specially treated MONOCORD tensile member and

an anti-abrasion compound reinforced with oriented fibres.• The moulded notch of these belts has been completely redefined so as to ensure optimum distribution of the

stresses: the fatigue due to centering is decreased substantially, which considerably reduces the appearanceof signs of wear (cracking).

• Produced with tight manufacturing tolerances, the TEXROPE® VRX belt has an angle of 28° for standardsections, and 26° or 28° for "VNN" sections.

• The large-base bevelling reduces the edge stresses.

T

W

Wp

α°


ISO 1604 sections W 16 W 20 W 25 W 31.5 W 40 W 50Nom. section W x T (mm) 17 x 6 21 x 7 26 x 8 33 x 10 42 x 13 52 x 16Pitch width Wp (mm) 16 20 25 31.5 40 50

ISO 1604 sections W 63 W 80 W 100Nom. section W x T (mm) 65 x 20 83 x 26 104 x 32Pitch width Wp (mm) 63 80 100

"VNN" sections, W x T (mm) 13 x 6 22 x 8 28 x 8 37 x 10 47 x 13 55 x 16Angle α° 26 26 26 28 28 28

Geometry of the sections

VRX 37x10x1250LI

19

450 W 16500 W 16560 W 16630 W 16800 W 16

560 W 20630 W 20710 W 20800 W 20900 W 20

1000 W 201120 W 201250 W 20

710 W 25800 W 25900 W 25

1000 W 251120 W 251250 W 251400 W 251600 W 25

900 W 31.51000 W 31.51120 W 31.51250 W 31.51400 W 31.51600 W 31.51800 W 31.5

1000 W 401120 W 401250 W 401400 W 401500 W 401600 W 401700 W 401800 W 402000 W 402240 W 402500 W 40

1120 W 501250 W 501400 W 501600 W 501700 W 501800 W 502000 W 502240 W 502500 W 502800 W 503150 W 50

TEXROPE ® VRX

TEXROPE ® VRX

ISO 1604 sectionsBelt codeLp mm

1600 W 631800 W 632000 W 632240 W 632500 W 632800 W 633150 W 633550 W 634000 W 63

ISO 1604 sectionsBelt codeLp mm

13 x 6 x 600 13 x 6 600 26°13 x 6 x 650 13 x 6 650 26°13 x 6 x 700 13 x 6 700 26°13 x 6 x 750 13 x 6 750 26°13 x 6 x 800 13 x 6 800 26°13 x 6 x 850 13 x 6 850 26°13 x 6 x 900 13 x 6 900 26°

22 x 8 x 600 22 x 8 600 26°22 x 8 x 650 22 x 8 650 26°22 x 8 x 700 22 x 8 700 26°22 x 8 x 750 22 x 8 750 26°22 x 8 x 800 22 x 8 800 26°22 x 8 x 850 22 x 8 850 26°22 x 8 x 900 22 x 8 900 26°22 x 8 x 950 22 x 8 950 26°22 x 8 x 1000 22 x 8 1000 26°22 x 8 x 1060 22 x 8 1060 26°22 x 8 x 1120 22 x 8 1120 26°

28 x 8 x 600 28 x 8 600 26°28 x 8 x 650 28 x 8 650 26°28 x 8 x 700 28 x 8 700 26°28 x 8 x 750 28 x 8 750 26°28 x 8 x 800 28 x 8 800 26°28 x 8 x 850 28 x 8 850 26°28 x 8 x 900 28 x 8 900 26°28 x 8 x 950 28 x 8 950 26°28 x 8 x 1000 28 x 8 1000 26°28 x 8 x 1060 28 x 8 1060 26°28 x 8 x 1120 28 x 8 1120 26°28 x 8 x 1180 28 x 8 1180 26°28 x 8 x 1250 28 x 8 1250 26°28 x 8 x 1320 28 x 8 1320 26°28 x 8 x 1400 28 x 8 1400 26°28 x 8 x 1500 28 x 8 1500 26°

37 x 10 x 750 37 x 10 750 28°37 x 10 x 800 37 x 10 800 28°37 x 10 x 850 37 x 10 850 28°37 x 10 x 900 37 x 10 900 28°37 x 10 x 950 37 x 10 950 28°37 x 10 x 1000 37 x 10 1000 28°37 x 10 x 1060 37 x 10 1060 28°37 x 10 x 1120 37 x 10 1120 28°37 x 10 x 1180 37 x 10 1180 28°37 x 10 x 1250 37 x 10 1250 28°37 x 10 x 1320 37 x 10 1320 28°37 x 10 x 1400 37 x 10 1400 28°37 x 10 x 1500 37 x 10 1500 28°37 x 10 x 1600 37 x 10 1600 28°37 x 10 x 1700 37 x 10 1700 28°

47 x 13 x 900 47 x 13 900 28°47 x 13 x 1000 47 x 13 1000 28°47 x 13 x 1060 47 x 13 1060 28°47 x 13 x 1120 47 x 13 1120 28°47 x 13 x 1180 47 x 13 1180 28°47 x 13 x 1250 47 x 13 1250 28°47 x 13 x 1320 47 x 13 1320 28°47 x 13 x 1400 47 x 13 1400 28°47 x 13 x 1500 47 x 13 1500 28°47 x 13 x 1600 47 x 13 1600 28°47 x 13 x 1700 47 x 13 1700 28°47 x 13 x 1800 47 x 13 1800 28°47 x 13 x 2000 47 x 13 2000 28°47 x 13 x 2240 47 x 13 2240 28°

55 x 16 x 1180 55 x 16 1180 28°55 x 16 x 1250 55 x 16 1250 28°55 x 16 x 1320 55 x 16 1320 28°55 x 16 x 1400 55 x 16 1400 28°55 x 16 x 1500 55 x 16 1500 28°55 x 16 x 1600 55 x 16 1600 28°55 x 16 x 1700 55 x 16 1700 28°55 x 16 x 1800 55 x 16 1800 28°55 x 16 x 2000 55 x 16 2000 28°55 x 16 x 2240 55 x 16 2240 28°

"VNN" sectionsBelt code Section Li Angle

(mm)

"VNN" sectionsBelt code Section Li Angle

(mm)

Dimensions in bold are availablefrom stock.

20

TEXROPE ® HEXAGOWrapped double-V belts

TEXROPE ® HEXAGO

The TEXROPE® HEXAGO double-V belt was developed forserpentine drives over V-grooved pulleys.

HBB 318 BB 122

Construction and features• Construction comparable to that of TEXROPE® S 84 classical V-belts.• Protected by a fabric cover.• MONOCORD high-strength tensile member.• The sections of this belt are designed for B and C section pulleys and

are designated HBB and HCC in accordance with standardASAE S 211.5.

• Good resistance to mineral oils and temperatures between -30°C and +60°C (+80°C for short periods).• Meets anti-static requirements (ISO 1813).

ApplicationsCurrently, its main area of application is in agricultural machinery.


hb

bb

bx

For further details on belt codes and minimum supplyrequirements, do not hesitate to consult us.

HBB HCCbb (mm) 17 23bx (mm) 11.8 16.8hb (mm) 13.5 17.5

HCC

Belt code RMA Code Leff (mm)

HCC 311 CC 118 3110HCC 316 CC 120 3160HCC 322 CC 122 3220HCC 326 CC 124 3260HCC 327 CC 124 3270HCC 331 CC 126 3310HCC 334 CC 127 3340HCC 352 CC 134 3520HCC 360 CC 137 3600HCC 367 CC 140 3670HCC 412 CC 157 4120HCC 420 CC 161 4200HCC 452 CC 173 4520HCC 463 CC 177 4630HCC 501 CC 192 5010HCC 518 CC 199 5180

HBB

Belt code RMA Code Leff (mm)

HBB 318 BB 122 3180HBB 382 BB 147 3820HBB 400 BB 154 4000HBB 415 BB 160 4150HBB 420 BB 162 4200HBB 441 BB 170 4410HBB 445 BB 172 4450HBB 453 BB 175 4530HBB 500 BB 194 5000HBB 533 BB 207 5330HBB 564 BB 220 5640


21

ApplicationsThis belt has been specially designed for:

• general-purpose or professional lawnmowers,• rotary cultivators,• mechanical hoes,• power reapers,• brushwood clearing machines,• scarifiers,• pick-up balers, etc.

TEXROPE ® LMBelts for agricultural machinery

LM 16 x 885 Lp

The TEXROPE® LM “Special Agricultural Machinery" belt has beendesigned to cope with the stresses specific to agricultural machineryapplications. It is the perfect belt for:- small-diameter pulleys: small bending radius- tensioners: reverse bending- clutching by idler: frequent slipping- very variable torque: shockloaded.

The TEXROPE® LM belt allows premium performance over small-diameterpulleys, more progressive clutching, more uniform performances and alonger service life.

Construction and features• The "super-low" section allows the belt to easily flex around small-

diameter pulleys. Stress fatigue is considerably reduced.• Because of sidewalls with optimised friction coefficient, clutch en-

gagement takes place progressively, until the maximum power istransmitted.

• Thanks to its raw edge, full-profile construction the belt transmits uniform power and gives long-lastingservice.


The TEXROPE® LM belt can be manufactured in all pitch lengths from 500 to 1800 mm in the followingsections:• 10 mm x 5 mm compatible with SPZ standard pulleys• 13 mm x 6 mm compatible with SPA standard pulleys• 16 mm x 7 mm compatible with SPB standard pulleys

LM 10 LM 13 LM 16Nom. section W x T (mm) 10 x 5 13 x 6 16 x 7Pitch width Wp (mm) 8 11 14Min. pulley diameter (mm) 50 63 90

TEXROPE ® LM

WWp

T

22

TEXROPE ® MULTI 84Classical-section banded V-belts

TEXROPE ® MULTI 84

The TEXROPE® MULTI 84 belt has been created by joining several classical-section strands to one single belt. This banded belt eliminates the need formatched sets, and prevents floating of the belts when clutching idlers areused.

MULTI 84 4000 HB3

Construction and features• The belt components are comparable to those of TEXROPE® S 84

belts.• The banded construction reduces belt whip by damping the vibra-

tions.• This banded belt consists of classical A, B or C belts, joined by a fabric-reinforced tie-band laid across the

top. Use of a flat idler is possible.• The belts have good resistance to mineral oils and temperatures between -30°C and +60°C (+80°C for short

periods).• They also meet anti-static requirements (ISO 1813) .

ApplicationsTEXROPE® MULTI 84 banded V-belts are particularly suited:• To replace a set of classical section belts on drives containing an idler. To solve whipping in drives subject to

frequent shocks or recurrent vibrations.• To high power agricultural drives, with or without clutching by idler.


When replacing a belt on an existing drive, it is advisable to check the centre distance of the pulley grooveswhich must comply with ISO standard 5290 as follows: HA centre distance 15.9 mm, HB centre distance19.05 mm, HC centre distance 25.4 mm.Consequently, these belts are compatible only with pulleys for banded belts of section B and C as specified byISO standard 4183.

HA HB HCSection A B CPulleys for belts dual/single dual/single dual/singlePulley standard ASAE S 211.5 ASAE S 211.5 ASAE S 211.5Centre distance of grooves e (mm) 15.9 19.05 25.4Le - Ld (mm) 16 22 34

DesignationThe designation of TEXROPE® MULTI 84 belts, in accordance with ISO standard 5290, refers to the number ofstrands, the section code HA, HB or HC and the effective length.

For further details on belt codes and minimum supply requirements, do not hesitate to contact us.

e

23

Construction and features• The belt components are comparable to those of TEXROPE® VP 2

belts.• This banded belt consists of 5V section strands (SPB compatible),

joined by a fabric tie-band laid across the top. Use of a flat idler ispossible.

• The belts have good resistance to mineral oils and temperatures between -30°C and +60°C (+80°C for shortperiods).

• They also meet anti-static requirements (ISO 1813).

15 J SPBSection SPB SPBPulleys for belts ‘dual’ ‘single’Pulley standard ISO 5290 ISO 4183Centre distance of grooves e (mm) 17.5 19.0Le - Ld (mm) 22 22

TEXROPE ® MULTI VP 2Narrow-section banded V-belts

TEXROPE ® MULTI VP 2

MULTI VP2 4/15J 3630 LE

The set of belts is replaced by a single belt, making installation easier andreducing vibrations as soon as they occur so that there is no belt whip.

ApplicationsTEXROPE® MULTI VP 2 belts are particularly suitable for drives with a tensioning or clutching idler on theback of the belt. They can also be used advantageously in drives subject to frequent shocks or variations intorque.

The spacing between the pulley grooves must comply with ISO standard 5290, i.e. 15 J for centre distance17.5 mm. These values differ from those in ISO standard 4183 specified for single-grooved pulleys of SPBsection.


DesignationIn accordance with ISO standard 5290, the designation of TEXROPE® MULTI VP 2 belts contains the number ofstrands, the section code (15 J for 5V sections) and the effective length.For further details on belt codes and minimum supply requirements, do not hesitate to contact us.

e

24

TEXROPE ® COMBITEX™Flexible link V-belts

The CombiTex™ V-belt consists of polyurethane links reinforced with polyes-ter fabric. This repair V-belt ensures a reliable performance even on thetoughest drives. CombiTex™ belts come in the same A, B and C cross-sections as conventional V-belts and can be installed on existing pulleyswithout any adaptation of the system. They are suitable for a large varietyof industrial applications and allow easy installation on hard-to-reachplaces.

Available from stock on rolls of 20 m.

Construction and features• High-tech polyurethane links reinforced with several plies of polyester

fabric build a tough, yet flexible belt.• The unique polyurethane compound is virtually immune to chemicals,

abrasion, oil, grease, water, steam and common industrial solvents.• The unique construction features high strength combined with low stretch;

it dampens transmitted engine vibrations extending the bearing life andreducing noise levels.

Available cross-sections

Section WidthA 13 mmB 17 mmC 22 mm

TEXROPE ® COMBITEX™

25

TEXROPE ® MA 3Flat belts with protected edges

The TEXROPE® MA 3 belt is a flat endless belt wrapped on all four sides.The fabric jacket is resistant to mineral oil splashing and exhibits goodabrasion resistance. The extra high-strength MONOCORD tensile memberand the specially developed compound are tailored to medium and heavy-duty drives.These properties make the belts particularly suitable for drives with clutch-ing idler and stepped speed pulleys such as those found on agriculturalmachinery.The TEXROPE® MA 3 belt meets anti-static requirements. It is 5.5 mm thickand weighs 690 g/m x 10 cm width.The TEXROPE® MA 3 belt is available in 18 widths and various lengths.For further details on belt codes and minimum supply requirements, do nothesitate to contact us.

AGRI 3000 x 120

TEXROPE ® MA 3

26

TEXROPE ® SPEEDFLEX®

Endless flat belts


Construction and features• It is tough and sufficiently flexible to withstand shocks and its tension

is constantly adjusted to optimise the stresses on the shafts.• Manufactured in sleeves of different lengths, it forms a thin and

symmetrical belt.• The continuous MONOCORD tensile member, manufactured in strengths corresponding to the belt type, can

cope with all power levels.• Its controlled flexibility enables it to be finely adjusted to power requirements.• Two fabric-reinforced faces have a high coefficient of friction and sufficient elasticity to pass around small-

diameter pulleys.• Can be cut to the width required for the application.

SPEEDFLEX TYPE 2 01500

The MONOCORD tensile member, inserted between two fabric-reinforcedfaces, imparts grip, flexibility and high strength to the SPEEDFLEX® belt. Itselasticity enables it to withstand shocks and stresses on the shafts. It isavailable in three strengths and can readily be adapted to therequirements of the drive.

ApplicationsSPEEDFLEX® is a lightweight belt which can cope with high speedswithout the centrifugal force reducing the drive capacity too much. As itis symmetrical, it will run in either direction and is particularly appropri-ate for serpentine drives. Being flat, it can be used on very smallpulleys, permitting large speed ratio drives.Available in three belt types and in many different lengths, and cut tothe required width, it covers a wide range of power levels.

e


The belt is measured on flat pulleys at the above measuring load F.The length tolerance (measured in tensioned state) is ±1%.The length of the belt in the free state is about 1% shorter than the nominal length.The calculation procedure in the manual "TEXROPE® Industrial Flat Belts" gives all the information required tocalculate a drive using TEXROPE® SPEEDFLEX®. Only available in French.

TYPE I TYPE II TYPE IIIApproximate thickness e (mm) 1.9 2.2 3Weight per 10 cm belt width (g/m) 240 270 400Available widths (mm) 15 up to 600 15 up to 600 300 up to 600Recommended min. pulley diameter (mm) 25 50 100

27TEXROPE ® SPEEDFLEX®

500 x x530 x x560 x x600 x x630 x x670 x x690 x x710 x x730 x x750 x x775 x x800 x x825 x x850 x x875 x x900 x x925 x x950 x x975 x x

1000 x x1030 x x1060 x x1090 x x1120 x x1150 x x1180 x x1215 x x1250 x x1285 x x1320 x x1360 x x1400 x x1450 x x1500 x x1550 x x1600 x x1650 x x1700 x x1750 x x1800 x x1850 x x1900 x x

SPEEDFLEX®

Length Type I Type II Type III(mm)

SPEEDFLEX®


1950 x x2000 x x2060 x x2120 x x2180 x x2240 x x2300 x x2360 x x2430 x x2500 x x2575 x x2650 x x2725 x x2800 x x2900 x x3000 x x3075 x x3150 x x3250 x x3350 x x3450 x x3550 x x3650 x x3750 x x3875 x x4000 x x4125 x x4250 x x4375 x x4500 x x4625 x x4750 x x4875 x x5000 x x5150 x x5300 x x5450 x x5600 x x5750 x x6000 x x6150 x x6300 x x

SPEEDFLEX®


6500 x x6700 x x6900 x x7100 x x7300 x x7500 x x7750 x x8000 x x8250 x x8500 x x8750 x x9000 x x9250 x x9500 x x9750 x x

10000 x x10300 x10600 x10900 x11200 x11500 x11800 x12150 x12500 x12850 x13200 x13600 x14000 x14500 x15000 x15500 x16000 x16500 x17000 x17500 x18000 x18500 x19000 x19500 x20000 x


Dimensions in bold are available from stock.TEXROPE® SPEEDFLEX® is only available in slabs. Please contact our sales department for more information.

28

TEXROPE ® STBSynchronous belts withtrapezoidal tooth profile

TEXROPE ® STB

The TEXROPE® STB synchronous belt with trapezoidal tooth profile providesa positive drive by the meshing of belt teeth with the pulley grooves, i.e.with no belt slip. The lightness of the belt, the fact that the tension is usedsolely for the necessary tractive force and that there is no lubricationrequired make it possible to simplify the drive design. Investment andmaintenance costs are thus considerably reduced.

Construction and features• This synchronous belt with standard trapezoidal tooth profile is

available in XL, L, H and XH profiles.• The tensile member provides tensile strength with virtually no stretch.• The flexible rubber top cover protects the tensile cords.

• The precision-moulded teeth provide ideal meshing.• The abrasion-resistant cover protects the teeth in their contact with the pulleys.• The covering also reduces noise.• The belt is resistant to commonly used oils and temperatures between -25°C and +100°C.• The meshing of the teeth prevents belt slip and speed variations, thus ensuring perfect synchronisation and a

positive drive.• The absence of metal-to-metal contact and the flexible meshing of the teeth considerably reduce the noise of

the synchronous system.• Complies with ISO standard 5296.

ht

p

40°

hs

ApplicationsThe positive belt drive, which uses the tension solely for tractive force, and the wide range of power levelscovered by the TEXROPE® STB synchronous belt make drive systems more compact and efficient and reducemaintenance costs.This belt range covers all industrial positive drive applications from hand-held tools to automated productionlines and includes machine tools and printing machines, etc.


STB 510 H 100NE PAS PLIERDO NOT CRIMPNICHT KNICKEN NON PIEGARE

STB 510 H 100

The calculation procedure in the manual "TEXROPE® Synchronous Belts" (ref. E/80019) gives all the informa-tion needed to calculate a drive using TEXROPE® STB belts. Only available in French and Italian.

XL L H XHPitch p (mm) 5.080 9.525 12.700 22.225Tooth height ht (mm) 1.27 1.91 2.29 6.35Nominal height hs (mm) 2.3 3.5 4.0 11.4Belt unit weight (g/m) for 1 mm width 2.4 3.2 3.9 11.3Min. pulley diameter in number of teeth 10 10 14 18Min. pitch diameter (mm) 16.17 30.32 56.6 127.34

29

Code mm XL L H XH

60 XL 152.4 3070 XL 177.8 3580 XL 203.2 4090 XL 228.6 45

100 XL 254.0 50110 XL 279.4 55120 XL 304.8 60130 XL 330.2 65140 XL 355.6 70150 XL 381.0 75160 XL 406.4 80170 XL 431.8 85180 XL 457.2 90190 XL 482.6 95200 XL 508.0 100210 XL 533.4 105220 XL 558.8 110230 XL 584.2 115240 XL 609.6 120250 XL 635.0 125260 XL 660.4 130

TEXROPE ® STB

TEXROPE ® STB

H

Belt code Lp (mm) N° of teeth

240 H 609.6 48270 H 685.8 54300 H 762.0 60330 H 838.2 66360 H 914.4 72390 H 990.6 78420 H 1066.8 84450 H 1143.0 90480 H 1219.2 96510 H 1295.4 102540 H 1371.6 108570 H 1447.8 114600 H 1524.0 120630 H 1600.2 126660 H 1676.4 132700 H 1778.0 140750 H 1905.0 150800 H 2032.0 160850 H 2159.0 170900 H 2286.0 180

1000 H 2540.0 2001100 H 2794.0 2201250 H 3175.0 2501400 H 3556.0 2801700 H 4318.0 340

L


124 L 314.3 33150 L 381.0 40187 L 476.3 50202 L 514.4 54210 L 533.4 56225 L 571.5 60240 L 609.6 64255 L 647.7 68270 L 685.8 72285 L 723.9 76300 L 762.0 80322 L 819.2 86345 L 876.3 92367 L 933.5 98390 L 990.6 104420 L 1066.8 112450 L 1143.0 120480 L 1219.2 128510 L 1295.4 136540 L 1371.6 144600 L 1524.0 160

XH


507 XH 1289.0 58560 XH 1422.4 64630 XH 1600.2 72700 XH 1778.0 80770 XH 1955.8 88840 XH 2133.6 96980 XH 2489.2 112

1120 XH 2844.8 1281260 XH 3200.4 1441400 XH 3556.0 1601540 XH 3911.6 1761750 XH 4445.0 200

XL


025 6.4 x037 9.5 x050 12.7 x075 19.1 x x100 25.4 x x150 38.1 x200 50.8 x x300 76.2 x x400 101.6 x

Standard widths:

Dimensions in bold are available from stock.The XXH belt is available on request.TEXROPE® STB belts are also available in slabs. Please consult TEXROPE® price list for more information on available widths.

30

TEXROPE ® HTD ®150Synchronous belts withimproved HTD® profile

TEXROPE ® HTD ®150

TEXROPE® HTD®150 is a universal synchronous belt transmitting up to 50%more power than the standard TEXROPE® HTD® belt. It is available in 8Mand 14M pitches and fits in HTD® 8 mm and 14 mm pulleys. No need toreplace the drive system, TEXROPE® HTD®150 ensures a perfect fit.

The belt also offers the benefits of standard HTD® belts which originate fromthe characteristics of its curved tooth profile:• High efficiency positive drive yielding significant cost savings;• Requires only minimum maintenance;• Reduces noise.

Construction• Body and teeth are made of a premium anti-static compound

meeting ISO 9563 (a certificate of conformity is supplied onrequest).

• The strong tensile cords provide the belt with its excellent flex lifeand resistance to elongation. Re-tensioning is unnecessary.

• The curvilinear tooth profile improves stress distribution, enhances load capacity and significantly reducesnoise levels. The teeth are made of a shear resistant rubber compound. They are accurately pitched andengage precisely with the pulley grooves.

• Good resistance to various oils and temperatures from -25°C to +100°C.• The flexible backing protects the cords against abrasive agents and major oils and contaminants.• The anti-abrasion facing protects the contact surfaces and also minimises noise levels.


ApplicationsTEXROPE® HTD®150 belts are suitable for all heavy-duty standard synchronous drive applications. They aretotally compatible with HTD® belts and can be mounted on any drive using 8M and 14M HTD® profile pulleys.They are designed to satisfy the power requirements of industrial and agricultural applications such as pumpsand blowers, agricultural equipment and machine tools.

The calculation procedure in the manual “TEXROPE® Synchronous belts” (ref. E/80019) ␣ gives all the informa-tion needed to calculate a drive using TEXROPE® HTD®150 belts. Only available in French and Italian.

hsht

p

8M 14MPitch p (mm) 8 14Tooth height ht (mm) 3.4 6.0Belt height hs (mm) 5.6 10.0Belt unit weight (g/m) for 1 mm width 5.5 9.6Minimal pulley outside diameter in number of teeth 22 28Minimal pitch diameter (mm) 56.02 124.78

HTD 1® 50HTD 1® 50

HTD 150 1778 14M1778 14M

31

Code mm 8M 14M



14MBelt Lp (mm) N° of teeth

reference

966 - 14M 966 691190 - 14M 1190 851400 - 14M 1400 1001610 - 14M 1610 1151778 - 14M 1778 1271890 - 14M 1890 1352100 - 14M 2100 1502310 - 14M 2310 1652450 - 14M 2450 1752590 - 14M 2590 1852800 - 14M 2800 2003150 - 14M 3150 2253500 - 14M 3500 2503850 - 14M 3850 2754326 - 14M 4326 3094578 - 14M 4578 3274956 - 14M 4956 354

8MBelt Lp (mm) N° of teeth

reference

384 - 8M 384 48 480 - 8M 480 60 560 - 8M 560 70 600 - 8M 600 75 640 - 8M 640 80 720 - 8M 720 90 800 - 8M 800 100 840 - 8M 840 105880 - 8M 880 110920 - 8M 920 115960 - 8M 960 1201040 - 8M 1040 1301120 - 8M 1120 1401200 - 8M 1200 1501280 - 8M 1280 1601440 - 8M 1440 1801600 - 8M 1600 2001760 - 8M 1760 2201800 - 8M 1800 2252000 - 8M 2000 2502400 - 8M 2400 3002600 - 8M 2600 3252800 - 8M 2800 3503048 - 8M 3048 3813280 - 8M 3280 4103600 - 8M 3600 4504400 - 8M 4400 550

20 20 x30 30 x40 40 x50 50 x55 55 x85 85 x x115 115 x170 170 x

Standard widths:

Dimensions in bold are available from stock.TEXROPE® HTD®150 belts are also available in slabs. Please consult TEXROPE® price list for more information on available widths.TEXROPE® HTD® 5M is available on request.

32

SynchroPower®

Polyurethane belts with metric pitch

SynchroPower®

SynchroPower® polyurethane metric pitch belts offer an optimal price/quality ratio. They provide maximum power transmission combined withperfect tooth meshing and tight and accurate tolerances. These belts canrun at linear speeds up to 75 m/s. Thanks to its improved flex fatigue life,the belt has a substantially increased service life.

Construction and features• Tough and flexible polyurethane compound provides consistent

quality.• Steel tensile member ensures high resistance to elongation.• Fixed centre distances are possible.

• Good resistance to various oils, ozone, abrasion and temperatures from -30°C to +80°C.• Efficiency to 98%.


ApplicationsSynchroPower® polyurethane belts with metric pitch are the ideal solution for applications in office machines,paper industry, mixers, domestic appliances, compressors, film projectors, sewing machines and toys, andespecially for applications where hygiene is of the utmost importance.

T2.5 T5 T10Pitch p (mm) 2.5 5.0 10.0Tooth height ht (mm) 0.7 1.2 2.5Belt height hs (mm) 1.3 2.2 4.5Min. pulley diameter in number of teeth 10 10 12Min. pitch diameter (mm) 7.95 15.91 38.19

AT5 AT10Pitch p (mm) 5.0 10.0Tooth height ht (mm) 1.2 2.5Belt height hs (mm) 2.7 5.0Min. pulley diameter in number of teeth 12 12Min. pitch diameter (mm) 19.09 38.19

hsht

ht

ht

hs

hsht

DL-T5 DL-T10Pitch p (mm) 5.0 10.0Tooth height ht (mm) 1.2 2.5Belt height hs (mm) 3.4 7.0Min. pulley diameter in number of teeth 10 12Min. pitch diameter (mm) 15.91 38.19

33

SynchroPower®

Endless construction

SynchroPower®

T10


T10 260 260 26T10 370 370 37T10 400 400 40T10 410 410 41T10 440 440 44T10 500 500 50T10 530 530 53T10 560 560 56T10 600 600 60T10 610 610 61T10 630 630 63T10 660 660 66T10 690 690 69T10 700 700 70T10 720 720 72T10 750 750 75T10 780 780 78T10 810 810 81T10 840 840 84T10 880 880 88T10 890 890 89T10 900 900 90T10 920 920 92T10 960 960 96T10 970 970 97T10 980 980 98T10 1010 1010 101T10 1080 1080 108T10 1110 1110 111T10 1140 1140 114T10 1150 1150 115T10 1210 1210 121T10 1240 1240 124T10 1250 1250 125T10 1300 1300 130T10 1320 1320 132T10 1350 1350 135T10 1390 1390 139T10 1400 1400 140T10 1420 1420 142T10 1460 1460 146T10 1500 1500 150T10 1560 1560 156T10 1610 1610 161T10 1750 1750 175T10 1780 1780 178T10 1880 1880 188T10 1960 1960 196T10 2250 2250 225

DL-T5


DL-T5 410 410 82DL-T5 460 460 92DL-T5 590 590 118DL-T5 620 620 124DL-T5 750 750 150DL-T5 815 815 163DL-T5 860 860 172DL-T5 940 940 188DL-T5 1100 1100 220

DL-T10


DL-T10 260 260 26DL-T10 530 530 53DL-T10 630 630 63DL-T10 660 660 66DL-T10 720 720 72DL-T10 840 840 84DL-T10 980 980 98DL-T10 1210 1210 121DL-T10 1240 1240 124DL-T10 1250 1250 125DL-T10 1320 1320 132DL-T10 1350 1350 135DL-T10 1420 1420 142DL-T10 1610 1610 161DL-T10 1880 1880 188

T5


T2.5


T2.5 120 120* 48T2.5 145 145* 58T2.5 160 160 64T2.5 177 177.5 71T2.5 180 180 72T2.5 200 200 80T2.5 230 230 92T2.5 245 245 98T2.5 265 265 106T2.5 285 285 114T2.5 290 290 116T2.5 305 305 122T2.5 317 317.5 127T2.5 330 330 132T2.5 380 380 152T2.5 420 420 168T2.5 480 480 192T2.5 500 500 200T2.5 600 600 240T2.5 620 620 248T2.5 650 650 260T2.5 680 680 272T2.5 780 780 312T2.5 880 880 352T2.5 915 915 366T2.5 950 950 380T2.5 1185 1185 474

T5 150 150* 30T5 185 185 37T5 200 200 40T5 210 210 42T5 215 215 43T5 220 220 44T5 225 225 45T5 245 245 49T5 250 250 50T5 255 255 51T5 260 260 52T5 270 270 54T5 280 280 56T5 295 295 59T5 305 305 61T5 330 330 66T5 340 340 68T5 350 350 70T5 355 355 71T5 365 365 73T5 390 390 78T5 400 400 80T5 410 410 82T5 420 420 84T5 455 455 91T5 475 475 95T5 480 480 96T5 500 500 100T5 510 510 102T5 525 525 105T5 545 545 109T5 550 550 110T5 560 560 112T5 575 575 115T5 590 590 118T5 610 610 122T5 620 620 124T5 630 630 126T5 650 650 130T5 660 660 132T5 690 690 138T5 720 720 144T5 750 750 150T5 780 780 156T5 815 815 163T5 830 830 166T5 840 840 168T5 885 885 177T5 900 900 180T5 940 940 188T5 990 990 198T5 1075 1075 215T5 1100 1100 220T5 1160 1160 232T5 1215 1215 243T5 1315 1315 263T5 1380 1380 276

Available as single belts and inslabs of 300 mm width.

* Slabs only available in240 mm width.





Dimensions in bold are availablefrom stock.

34

4 4 x6 6 x x x8 8 x x x

10 10 x x x x x x x12 12 x x x x x16 16 x x x x x x20 20 x x x x25 25 x x x x x x32 32 x x x x x50 50 x x x x

Standard widths for single belts:

AT10 500 500 50AT10 560 560 56AT10 610 610 61AT10 660 660 66AT10 700 700 70AT10 730 730 73AT10 780 780 78AT10 800 800 80AT10 810 810 81AT10 840 840 84AT10 890 890 89AT10 920 920 92AT10 960 960 96AT10 980 980 98AT10 1010 1010 101AT10 1050 1050 105AT10 1080 1080 108AT10 1150 1150 115AT10 1210 1210 121AT10 1250 1250 125AT10 1320 1320 132AT10 1400 1400 140AT10 1500 1500 150AT10 1600 1600 160AT10 1700 1700 170AT10 1800 1800 180

AT5


AT5 225 225 45AT5 255 255 51AT5 275 275 55AT5 280 280 56AT5 300 300 60AT5 340 340 68AT5 375 375 75AT5 390 390 78AT5 420 420 84AT5 455 455 91AT5 500 500 100AT5 545 545 109AT5 600 600 120AT5 610 610 122AT5 630 630 126AT5 660 660 132AT5 720 720 144AT5 750 750 150AT5 780 780 156AT5 825 825 165AT5 975 975 195AT5 1050 1050 210AT5 1125 1125 225AT5 1500 1500 300

SynchroPower®

Endless construction

SynchroPower ®


AT10


SynchroPower®

Open-ended construction

T profile Widthmm / code

T5 6, 10, 16, 25, 32, 50

T10 16, 25, 32, 50, 75, 100

AT profile Widthmm / code

AT5 6, 10, 16, 25, 32, 50

AT10 16, 25, 32, 50, 75, 100

STB profile Widthmm / code

L 037, 050, 075, 100, 150

H 050, 075, 100, 150, 200, 300, 400

Steel tensile memberOnly available on rolls of 50 m

Code mm T2.5 T5 T10 DL-T5 DL-T10 AT5 AT10



35

TEXROPE ® LLOpen-ended synchronous belts with STB or

HTD® tooth profile

TEXROPE ® LL

TEXROPE® LL synchronous open-ended rubber belts are available in STB(trapezoidal) or HTD® (curved) profiles and with two types of tensilemember:- standard, i.e. glass-fibre;- metal, i.e. steel cords (with the word STEEL on the belt).TEXROPE® LL belts are cut straight. Their teeth, which are strictly at rightangles to the edges, guarantee precise positioning in all applications withlinear movement.LL HTD 8M-20

STB profile

HTD® profile

Available on rolls of 30 m.Dimensions in bold are available from stock.3M and 5M belts are available on request.

Belt code Width(mm)

LL XL 025 6.35LL XL 031 7.94LL XL 037 9.53LL XL 050 12.70LL L 037 9.53LL L 050 12.70LL L 075 19.05LL L 100 25.40LL H 050 12.70LL H 075 19.05LL H 100 25.40LL H 150 38.10LL H 200 50.80LL H 300 76.20

Belt code Width(mm)

LL 8M 10 10LL 8M 15 15LL 8M 20 20LL 8M 30 30LL 8M 50 50LL 8M 85 85LL 14M 25 25LL 14M 40 40LL 14M 55 55LL 14M 85 85LL 14M 115 115

The calculation procedure in the manual “TEXROPE® Synchronous belts” (ref. E/80019) ␣ gives all the informa-tion needed to calculate a drive using TEXROPE® Long Length belts. Only available in French and Italian.

ht

p

40°

hs


XL L H XHPitch p (mm) 5.080 9.525 12.700 22.225Tooth height ht (mm) 1.27 1.91 2.29 6.35Nominal height hs (mm) 2.3 3.5 4.0 11.4Belt unit weight (g/m) for 1 mm width 2.4 3.2 3.9 11.3Min. pulley diameter in number of teeth 10 10 14 18Min. pitch diameter (mm) 16.17 30.32 56.6 127.34


hsht

p

8M 14MPitch p (mm) 8 14Tooth height ht (mm) 3.4 6.0Belt height hs (mm) 5.6 10.0Belt unit weight (g/m) for 1 mm width 5.5 9.6Minimal pulley outside diameter in number of teeth 22 28Minimal pitch diameter (mm) 56.02 124.78

36

TEXROPE ® DFDouble-sided synchronous belts with STBor HTD® tooth profile

TEXROPE® DF double-sided endless belts, in STB (trapezoidal) or HTD®

(curved) profiles, are designed for synchronous drives with contra-rotatingshafts.TEXROPE® DF belts are particularly suitable for serpentine drives. Theirperfect symmetry enables the power rating to be distributed anywherebetween the two faces.

Physical characteristicsSTB profile

HTD® profile

TEXROPE ® DF

p

hs e

STB profile HTD® profileXL L H 8M 14M

Pitch p (mm) 5.08 9.53 12.7 8 14Nominal height hs (mm) 3.0 4.5 5.8 8.3 14.9Thickness between teeth e (mm) 0.5 0.8 1.4 1.4 2.8Belt unit weight (g/m) for 1 mm width. 1.9 3.2 4.6 7.2 12.3

The calculation procedure in the manual “TEXROPE® Synchronous belts” (ref. E/80019) ␣ gives all the informa-tion needed to calculate a drive using TEXROPE® DF belts. Only available in French and Italian.

hs

p

e

37

H


360 H 914.4 72390 H 990.6 78420 H 1066.8 84450 H 1143.0 90480 H 1219.2 96510 H 1295.4 102540 H 1371.6 108570 H 1447.8 114600 H 1524.0 120630 H 1600.2 126660 H 1676.4 132700 H 1778.0 140750 H 1905.0 150800 H 2032.0 160850 H 2159.0 170900 H 2286.0 180

1000 H 2540.0 2001100 H 2794.0 2201250 H 3175.0 2501400 H 3556.0 2801700 H 4318.0 340

14M


1610 - 14M 1610 1151778 - 14M 1778 1271890 - 14M 1890 1352100 - 14M 2100 1502310 - 14M 2310 1652450 - 14M 2450 1752590 - 14M 2590 1852800 - 14M 2800 2003150 - 14M 3150 225

L


210 L 533.4 56225 L 571.5 60

240 L 609.6 64255 L 647.7 68270 L 685.8 72285 L 723.9 76300 L 762.0 80

322 L 819.2 86345 L 876.3 92367 L 933.5 98390 L 990.6 104

420 L 1066.8 112450 L 1143.0 120480 L 1219.2 128510 L 1295.4 136540 L 1371.6 144

600 L 1524.0 160

8M


XL


150 XL 381.0 75160 XL 406.4 80

170 XL 431.8 85180 XL 457.2 90190 XL 482.6 95200 XL 508.0 100210 XL 533.4 105

220 XL 558.8 110230 XL 584.2 115240 XL 609.6 120250 XL 635.0 125

260 XL 660.4 130

␣

Standard widths:Code mm 8M 14M

20 20 x30 30 x40 40 x50 50 x55 55 x85 85 x x

480 - 8M 480 60560 - 8M 560 70600 - 8M 600 75640 - 8M 640 80720 - 8M 720 90800 - 8M 800 100880 - 8M 880 110960 - 8M 960 120

1040 - 8M 1040 1301120 - 8M 1120 1401200 - 8M 1200 1501280 - 8M 1280 1601440 - 8M 1440 1801600 - 8M 1600 2001760 - 8M 1760 2201800 - 8M 1800 2252000 - 8M 2000 2502400 - 8M 2400 3002800 - 8M 2800 350


TEXROPE ® DF

TEXROPE ® DF

Code mm XL L H

025 6.4 x037 9.5 x050 12.7 x075 19.1 x x100 25.4 x x150 38.1 x200 50.8 x300 76.2 x

38

TEXROPE® CFXFlexible couplings

The new TEXROPE® CFX flexible couplings are strong, highly efficient,positive couplings capable of absorbing load pulsation and shocks.TEXROPE® CFX couplings are recommended for general use, but also giveexcellent performance in troublesome conditions.

Construction and features• Flexible sleeve featuring axially moulded internal teeth.• Two end pieces with grooves to mate with teeth of the sleeve. To each shaft

one end piece can be attached.• High resistance to shock loads with a high torsional resilience.• Noise and vibration reduction: the high damping factor and progressive

torsional stiffness of the sleeve reduces transmitted noise and vibration aidingthe elimination of resonance effects.

• Overload protection: sleeve can act as a “fuse” preventing damage to expensive components in cases of machine blockages.

• Tolerance to misalignment: in normal use the coupling tolerates up to 7° axialmisalignment, with no significant reduction in service life.

• Easy installation by eye shaft alignment; no precise measurements required.• No need for lubrication as the elastomeric teeth of the sleeve positively fit with

the grooves of the end fittings and there is no metal-to-metal contact.• No end thrust: construction prevents the transmission of lateral thrust from one shaft to another.• Low cost: low initial cost and low maintenance costs due to the simplified design.• Versatility: because supplied in minimum plain bore (with set screw) end pieces can be bored to size.

TEXROPE ® CFX

The drive design procedure in the brochure E2/80026 gives all the information needed to calculate a drive using TEXROPE® CFX couplings.

39

Complete Rubber sleeve End piececoupling

Ref A B C D E F min. F max. G Hplain bore bore

mm mm mm mm mm mm mm mm mm

CFX 11 24.5 13.3 18.5 18.0 5.6 4.0 9.0 1.0 2.8CFX 21 56.0 40.0 29.0 30.0 8.0 8.0 15.0 2.0 4.0CFX 33 58.7 39.7 38.1 36.5 9.5 9.5 15.9 1.6 4.8CFX 43 58.7 39.7 44.5 41.3 9.5 9.5 22.2 1.6 4.8CFX 56 61.9 39.7 58.7 52.4 11.1 14.0 30.2 1.6 5.6CFX 66 69.1 40.5 74.6 69.9 14.3 14.0 35.0 2.4 7.1CFX 76 87.4 54.0 88.9 82.6 16.7 12.7 41.3 3.2 8.7CFX 86 87.4 54.0 103.2 95.3 16.7 12.7 47.6 3.2 8.7

Note: End pieces are supplied in minimum plain bore with set screw.

B

G

A

F DC

HE

TEXROPE ® CFX

TEXROPE® CFX


40

TEXROPE® ATXLaser alignment device

Noise, wear on pulleys, belts and bearings, vibrations and in the endmachine downtime may all be caused by improper pulley alignment. Thecurrent method to measure misalignment is putting a straight edge up to thepulleys. A much faster and more accurate method is ensured by the uniquelaser alignment device, TEXROPE® ATX. Mounted in a few seconds, thelaser line projected onto the targets allows you to quickly ascertain andcorrect misalignment. The TEXROPE® ATX identifies parallel as well asangular misalignment between the pulleys. The laser line is projected on the targets and when the line lies inthe slots of the targets, the machine is in the right position. The result is fast and precise alignment.

The TEXROPE® ATX laser alignment device is so light it can be mounted on non-magnetic pulleys with thedouble sided adhesive tape. It can be used on both horizontally and vertically mounted machines and issuitable for pulley diameters of 60 mm and larger.

Construction• For both V-belts and synchronous belts.• Shows parallel and angular misalignment between the pulleys.• Much faster and more accurate than measuring with earlier, conventional

methods.• For both horizontally and vertically mounted machines.• Alignment can be made by one operator.• Also suitable for non-magnetic pulleys.• Calibration accuracy: offset < 0.5 mm; angle < 0.1°.• Targets: 2 pieces magnet targets with adjustable centre line.

Technical characteristics• Pulley diameters ≥ 60 mm• Beam angle 78°• Measurement distance 10 m (33 ft)• Battery 1 x R6 (AA) 1.5 V• Battery operation 8 hours continuously• Laser class 2• Output power < 1 mW• Laser wave length 635 – 670 nm• Temperature range -10°C up to +50°C• Housing ABS plastics• Back plate Anodised aluminium• Weight 0.25 kg• Dimensions: W 147 mm x H 87 mm x D 28 mm

NOTE: THE TEXROPE® ATX SHOULD NOT BE USED IN EXPLOSIVE RISK AREAS.

TEXROPE ® ATX

Special constructionsSubject to minimum order quantities, we can supply TEXROPE® belts with special characteristics. Pleasecontact us.

AdviceAdvice is of course, an integral part of the TEXROPE® service. Our calculation manuals are available onrequest. Our Distributors are also able to advise you and help you calculate drives thanks to the necessarysoftware and training they have been given. The multilingual TEXROPE® drive design software runsunder Windows. Available on CD-ROM(E/80008), the program simplifies the drive calculation of V-belts and synchronous belts depending on thecriteria and limitations specified by the user.The software runs under Windows 95, 98, 2000, NT or Millennium and requires a Pentium 133 processor orhigher.In difficult cases our application engineers can do the calculations for you. Ranging from the simple task ofchecking an existing drive to the design of new equipment, TEXROPE® can supply all you need to ensure aperfectly operating drive system.

Care and maintenanceTo get the best out of your TEXROPE® belt drive, here are some tips on care and maintenance.- Storage:

Drive belts can be stored for long periods in a clean, properly ventilated stockroom at normal ambienttemperature, away from direct sunlight, UV radiation and ozone.They may be reeled, but must not be stacked under excessive loads; they may not be bent, squeezed ortightly folded.They can be stored vertically on pegs provided that the pegs do not have sharp edges and are of a suffi-ciently large diameter.

- Installation:Pulleys must be very clean and have the correct profile.The shafts must be parallel, the pulley grooves must be correctly aligned, and the belts fitted without forcing.If there is an idler, it must have a recommended minimum diameter and be positioned on the slack side soas to ensure a big enough arc of contact on the small pulley.If one or more belts in a drive system should fail, the complete set must be replaced.

- Tensioning:The life of a belt largely depends on the proper tension. You should follow the tensioning instructions and,after the drive has been run in, check the tension using the deflection or elongation method.

- Maintenance:Belt maintenance is usually a matter of checking the belt for cleanliness, alignment and tension.But it is also important to keep the other drive components in good condition and, in particular, to checkpulley wear, the condition and lubrication of bearings, the rigidity of structures and parallel alignment of theshafts.

TEXROPE® web siteYou can visit TEXROPE® on www.texrope.com, where you will find a detailed company and product descrip-tion. Surfing from one product to another is no problem and product information can be easily downloaded.Information on the TEXROPE® services includes contact details of the sales team, advice of application engi-neers and distributors and an overview of the marketing communication support.An online e-mail function allows you to get directly in touch with the right person. Our Distributors can alsoinstall a link between their own web site and the TEXROPE® site, in order to offer their customers at all timesthe latest information on TEXROPE® products.

The manufacturers reserve the right to amend details where necessary. © Gates S.A. 2003 Printed in Belgium - 10/03.

Important:

Every effort has been made to ensure that the information contained in this manual is complete and accurate. Nevertheless,the manufacturer cannot be held responsible for errors or omissions which have occurred after its release for printing; or for the use of itsproducts in special or exceptional circumstances if a TEXROPE® representative has not been consulted beforehand about the suitability ofthe intended application.This issue is released October 2003 and supersedes all previous versions. If your catalogue is more than2 years old, please consult a TEXROPE® representative to check whether you have the latest version.

Your TEXROPE® distributor:

DeutschlandTEXROPE®

Industrieriemen␣Haus Gravener Straße 191-193D - 40764 LangenfeldTl : (49) 2173 / 795-0Fx : (49) 2173 / [email protected]

ItaliaTEXROPE®

Cinghie IndustrialiVia Senigallia 18(Int. 2 - Blocco A - Edificio 1)I - 20161 Milano MITl : (39) 02 / 66 21 62 24

(39) 02 / 66 21 62 25Fx : (39) 02 / 66 22 10 [email protected]

FranceTEXROPE®

Courroies IndustriellesB.P. 37Zone IndustrielleF - 95380 LouvresTl : (33) 1 / 34 47 41 31Fx : (33) 1 / 34 72 60 [email protected]

80001/e1 texrope ib vsml-group.ru/f/texrope-remni-katalog.pdf · 2020-03-03 · 1 texrope ®...

Documents