8. 9. - unt digital library/67531/metadc722881/... · 1,tfortest 2. commercial grade survey 3....

2. To: (Receiving Organization) I 3. From: (Originating Organization) I 4. Related EDT No.: - - Distribution 5 . Proj./Prog.lDept./Div.:

SNF Project NIA 6. Design Authority/ Design Agenucog. 7. Purchase Order No.:

Enm.: Spent Nuclear Fuel Project 8. Originator Remarks: NIA

I C. V& Katwijk

11. Receiver Remarks: 11A. Design Baseline Document? [I Yes [XI No

NIA 14. Required Response Date:

NIA 9. Equip./Component No.:

NIA 10. System/Bldg./Facility:

Spent Nuclear Facility 12. Major Assm. Dwg. No.:

N/A 13. Pennitlpemit Application No.:

15. DATA TRANSMITTED (F) (G) (H) (A) (B) DocumentlDraw4ngNo. (C) (D) (E) Title or Description of Data Approval Reason Origi- lrem Sheet Rev. Transmitled Desig- for nator NO. NO. NO. mor Trans D i s p

mittal sition

(1) Receiv-

er D i s p sition

0 MKS Baratron MCO Absolute PIessure Q 2 1 1 SNF-3892 Transmitter

16. KEY

NIA

I I I I I I I

ED-7400-172-1

SNF-3892, Rev. 0

MKS Baratron MCO Absolute Pressure Transmitter

Carl Van Katwijk Numatec Hanford Co, Richland, WA 99352 U.S. Department of Energy Contract DE-AC06-96RL13200

EDTECN: 626265 U C 620 Org Code: 2G300 B&R Code: 39EW40400

Charge Code: lOSSS9/AOOO Total Pages: \ 8

Key Words: Absolute Pressure Transmitter - MCO

Abstract: M K S Baratron MCO Absolute Pressure Transmitter CGI-SNF-D- 13-P4-0 19

TRADEMARK DISCLAIMER. Reference herein to any specific commercial product, p r w , or rervice by trade mine, trademark, manufachlrer, or otherwise, d m not necessarily canajrue rn hp?v jls mdorrement, recommendation, or Favoring by the United States Government or any agency thereof or its contracton or s~lxontra~tors

Printed in the United State ofAmerica. To obtain copies ofthis document, contact: Deament Control Services, P.O. Box 950, Mailstop H6-08, Richland WA 99352, Phone (509) 372-2420; Fax (509) 376-4989.

/

Approved for Public Release A-6400-073 (01/97) GEF321

Rev. No. 0 Commercial Grade Item Upgrade Dedication Form CGI NO. CGI-SNF-D-l3-P4-019 Page I of 12

SNF- 3892 ECNNo. NA Title: MKS BARATRON MCO ABSOLUTE PRESSURE TRANSMITTER

Item No.: NA I Manufacturer: I Supplier:

Mfg. PaltlModel No.: Supplier's PIN:

End Use Description:

Equipment No.: He-PT-1'35

Specification No.: Manufacturer: Past P.O. No.: NA W-441-P4 Rev. 2 MKS Instruments

Manufacturer's ParV Model No.: MKS Baratron PT 430C A 00100

1, Is the Item available from a catalogue from a qualified NQAl supplier interface Engineer or BTR)?

[ ] YES (go to #2 below) [ X ] NO (go to procedure step 5.3.2, proceed to dedicate Item

company name &type phone 2. List of Candidate qualified s u p p l i e r s a m p ' L-4 1 2 r , \ q t

NA

Equipment Supplier (if different from manufacturer): TBD Equip. Supplier's Part No.: NA

3. Recommended Procurement Strategy(co0rdinate with project CGI interface Engineer or BTR): NA

1. Question #I: Is the Item subject to design or specification requirements that are unique to nuclear facilities or activities? [ 1 YES (lhe Item is not commercial grade) [ X I NO (continue)

[ ] NO (the item is not commercial grade) [ X I YES (continue)

2. Question #2: Is the Item used in applications other than nuclear facilities or activities?

12/21/98

Commercial Grade Item Upgrade Dedication Form CGI NO. CGI-SNF-D-13-P4-019 ECNNo. NA

Title: MKS BARATRON MCO ABSOLUTE PRESSURE TRANSMITTER

I. Question #3: Is the Item ordered from manufacturer/supplier on the basis or specifications set folth in the manufacturers catalog?

[ ] NO (the Item is not commercial grade) [ X I YES (continue)

Rev. No. 0

Page 2 of 12 SNF-3832

X ] Item is being purchased from a non ESL manufacturer supplier as commercial grade to be used in a Safety Class

]

]

Item is being purchased from a non ESL manufacturer supplier as commercial grade to be used in a Safety Significant application. Item was purchased from a non ESL manufacturer supplier as commercial grade to be used in a Safety Class application. Item was purchased from a non ESL manufacturer supplier as commercial grade to be used in a Safely Significant application.

]

] Other (line-for like', simi ar. substtAon replacement eva uabon)

&!!?k 1. PaiVComponent Safety Function: I. Pressure Boundary 2. 3. 3. PaiVComponent Functional Mode:

Maintain Pressure Boundary After Seismic Event

Safely Function #I:

[ ] , Active - Mechanical or Electrical change of state is required to occur for the component to perform its safety function [ X ] Passive - Change of state is not required for the component to perform its safely function

[ ] Active - Mechanical or Electrical change of state is required to occur for the component to perform its safety function . [ X ] Passive -Change of state is not required for the component to perform its safety function

[ ] Active - Mechanical or Electrical change of state is required to occur for the component to perform its safety function. [ ] Passive - Change of state is not required for the component to perform its safety function

Safety Function #2:

Safely Function #3:

C. Host Component Safety Function ( i applicable):

2. 3.

1212 1/98

Commercial Grade Item Upgrade Dedication Form ECNNo. NA CGINO. CGI-SNF-D-13-P4-019 Titlc: MKS BARATRON MCO ABSOLUTE PRESSURE TRANSMITTER

D. Failure Mode($ and the effects on component or system safetyfunction (see Worksheet 1): 1. PT process connection break/PT body break - inleakage of air. 2. Inaccurate pressure signal due to damage from pressure outside instrument

3. indicator range.

Rev. No. 0


5

Environmental Qualification Required: If yes: Environmental Qualification Requirements Yes[ 1 Limiting Environmental Conditions: No [ X I Required Safety Functions:

Environmental Condition B Qualification Period:

Natural Phenomena Hazard (NPH) Design Required: If yes: NPH Design Requirements Performance Category: PC-3 NPH Design Req'ts.: Seismic Condition B Yes [ X I

No I 1 Required Safety Functions: Pressure Boundary HNF-PRO-97, Rev. 0 Integrity

W-441-P4, Rev. 2

[ X ] Safety Class (SC) [ ] General Selvice [ ] Safety Significant (SS) If partkomponent classification is different from host componentlsystem, document basis.

National CodesEtandards: Safety Analysis Report (SAR): Drawings: H-1-82161, Rev. 2 IEEE 344, SA-S5.I. S5.4, HNF-SD-SNF-SAR-002, HNF-SD-SNF-SEL-002, Rev. 4 S18.1, S20 Rev. 4A

Vendor ManuaVManufacturer/Supplier Information: MKS Instruments Baratron Absolute Pressure Transmitters 400 Series

12/21/98

Commercial Grade Item Upgrade Dedication Form CGI NO. CGI-SNF-D-13-P4-019 ECNNo. h%

Title: MKS BARATRON MCO ABSOLUTE PRESSURE TRANSMITTER

Rev. No. 0


Seismic Condition B Notes and Legend: 1. The instrument has ceramic electrodes and nonmetallic terminal

strips. These materials are not subject to Degradation at 4OoF and 60% RH or 115OF and 22% RH and are suitable for Condition B application.

2. Maintain pressure boundary after Seismic event. W-441 -P4, Rev. 2, Appendix L, page L-12, provides a seismic testing plan for these components at a (TBDI seismic spectra. "Confinement" leakage acceptance criteria is < I O 4 scdsec.

3. Pressure test at 110% of design accident condition pressure of 150 psig (Destructive Test). Vendor sheet states overpressure limit of 35 psig, consequently this test is considered to be a destructive test.

4. Testing (Seismic and pressure boundary) is being performed for PT-1'08 (CGCSNF-D-07-P4-010). Both instruments are Baratron Series 400 and have identical pressure boundaries. Destructive testing of PT-1'08 will provide verification of the critical characteristics for this component.

I Notes 2 and 4

Document: Vendor Specifications: HNF-SD-SNF-SEL-002 Rev. 4 1. Item Identification Critical Characteristics Nameplate Data

Modellpart Number

Housing

Process Connection 2. Physical Critical Characteristics (for Material, Body

Material, Process Connection 3. Performance Critical Characteristics (for Pressure Boundary

Repeatability

Inputloutput Voltage/ Operating Rangel Accuracy

Insulation Resistance Environmental

I 1 . T I I X Acceptance Method: 1. Special Test and Inspection

1, IN for Inspection 1,TforTest

2. Commercial Grade Survey 3. Source Verification 4. Vendor/ltem History

Method

(necessary for reasonable assurance that the Item delivered is the Item specified)

Per Vendor Manual 1. IN X 430C AOOIOO 1, IN X NEMA 4 1, IN X %.- 18 NPT 1,IN X

reasonable assurance that the Item delivered is the Item specified)

Cast Aluminum 1.T X Stainless Steel 1.T X reasonable assurance that the Item will perform its intended safety function(s)) Pressure Test at Pressure of 165 Psig (No X Leakage) Notes 3 and 4

NA

NA

1. T

NA

Note 1

12/21/98

Commercial Grade Item Upgrade Dedication Form ECNNo. NA CGI NO. CGI-SNF-D-13-P4-019 ~ i t k MKS BARATRON MCO ABSOLUTE PRESSURE TRANSMITTER

12/21/98

Rev. No. 0


Commercial Grade Item Upgrade Dedication Form ECNNo. NA CGINo. CGI-SNF-D-13-P4-019 TU^: MKS BARATRON MCO ABSOLUTE PRESSURE TRANSMITTER

WORKSHEET 1 DETERMINATION OF FAILURE MECHANlSMSlMODES

SeDaration of a solid accomoanied bv little or no Yes [ ] No [X I , If Yes, indicate failure

Rev. No. 0


Fracture

Corrosion

Erosion

Open Circuit

Short Circuit

Blockage

Seizure

Unacceptable Vibration

Loss of Properties

Excess Strain

Mechanical Creep

Ductile Fracture

macroscopic plastic deformation

The gradual deterioration of a material due to chemical or electrochemical reactions, such as oxidation, between the material and its environment. Destruction of materials by the abrasive action of moving fluids, usually accelerated by the presence of solid palticles carried with the fluid. An electrical circuit that is unintentionally broken so that there is no cmplete path for current flow.

An abnormal connection by which an electrical current is connected to ground, or to some conducting body, resulting in excessive current flow. Clogging of a filtering medium resulting in the inability to perform its purification function or blockage of flow. Binding of a normally moving item through excessive pressure, temperature, friction, jamming.

Mechanical oscillations produced are beyond the defined permissible limits due to unbalancing, poor support, or rotation at critical speeds.

A loss of mechanical and physical properties of a material due to exposure to high temperatures, radiation exposure. Under the action of excessive external forces the material of the part has been deformed or distorted.

From prolonged exposure to high temperature and stress, the object will show a slow change in its physical (shape and dimension) and mechanical characteristics. Fracture characterized by tearing of metal accompanied by appreciable gross plastic

Yes [ ] No [X I ; If Yes, indicate failure Mode

Yes [ ] No [ XI; If Yes, indicate failure Mode

Yes [ ] No [XI; If Yes, indicate failure Mode



Yes [ ] No [ XI; If Yes, indicate failure Mode

Yes [ 1 No [XI; If Yes, indicate failure

Yes [ ] No [XI; If Yes, indicate failure Mode

Yes [ 1 No [X I ; If Yes, indicate failure Mode



deformaton Sect1011 2 Additional Failure Modes AppflcabIe to the Component Under Evaluation

1. Process Connection Break

2. Transmitter Body Break

3. Diaphragm Assembly Loss

4. Deformation due to excessive Dressure.

12/2 1/98

Commercial Grade Item Upgrade Dedication Form ECNNo. NA CGINO. CGI-SNF-D-13-P4-019 Title: MKS BARATRON MCO ABSOLUTE PRESSURE TRANSMITTER

SPECIAL TESTm

Rev. No. 0


Item Description: Baratron Absolute Pressure Transmitter

Svstem#: 13

Manufacturer (Addresflhone):

MKS Instruments

Six Shattuck Road

Andover, MA 01810

(800) 227-8766

P.O. #

I N P - 1 x 1 1 x 1 1 x 1 1 x 1 I 1 1 1 1 1 1 1 1 1 1 1 I 1 - - * see -

rm Poot Ted ~

I 1 1 1 I 1 I 1 1 x 1 1 x 1 1 x 1 1 1 1 1 1 1 [ X I - -

- I 1 I 1 I 1 I 1 I 1 1 1 1 1 1 1 1 1 1 1

PECTION VEIUFICATION N f

Equip #: He-PT-1*35 Model,#: BARATRON PT 430C AOOIOO

Supplier (Addressphone):

,RISTICS TO BE VERIFIED BY METHOD 1.

1. Nameplate Data

2. Modellpart Number

3. Housing

4. Process Connection

5. Material, Body

6. Material, Process Connection

7. Pressure Boundary

8. Repeatability

9. Inputloutput Voltage Operating RangelAccuracy

I O . Insulation Resistance

ttachment G of Desk Instruction for Samphng Sue Characteristic: Nameplate Data

Sample Size*: All Items

Acceptance Criteria: Per Vendor Manual

Receipt Inspection Plan / Report #:

References (see Section 7): Baratron Absolute Pressure Transmitter 400 Series

1212 1/98

Commercial Grade Item Upgrade Dedication Form ECNNo. NA CGI NO. CGI-SNF-D-13-P4-019 Title: MKS BARATRON MCO ABSOLUTE PRESSURE TRANSMITTER

Characteristic: Modellpart Number


Acceptance Criteria: 430C AOOIOO


References (see Section 7 ) :

Rev. No. 0


Characteristic: Housing


Acceptance Criteria: NEMA 4


References (see Section 7):

Characteristic: Process Connection


Acceptance Criteria: '/4 - 18 NPT Receipt Inspection Plan I Report #:

References (scc Scction 7)

SECTlON 4 BY SPECLA

* See Attachment G of Desk Instruction for Sampling Size

[ ] Purchaser

[ ] Supplier/Manufacturer**

[ ]Other

TestAnspection Location:

Characteristic for Test: Material, Body

Acceptance Criteria: Cast Aluminum

Sample Size*: Normal Sampling Size

Actual Test Value:

Test Plan and Report #:

Characteristic for Test: Material, Process Connection

Acceptance Criteria: Stainless Steel

Sample Size*: Normal Sampling Size

Actual Test Value:

Test Plan and Report #.



12/21/98

Rev NO. 0 Commercial Grade Item Upgrade Dedication Form Page 9 of 12

SNF-3892 ECNNo. NA CGI No. CGI-SNF-D-13-P4-019 Title: MKS BARATRON MCO ABSOLUTE PRESSURE TRANSMITTER

Characteristic for Test: Pressure Boundary

Acceptance Criteria: Pressure Test at Pressure of 165 Psig (No Leakage)

Sample Size*: Destructively Test Only One Item. Pressure boundary testing is being performed for PT-1 *OS (CGl-SNF-D-07-P4-010). Both instruments are Baratron Series 400 and have identical pressure boundaries. Destructive testing of PT-1'08 will provide verification of the critical characteristics for this component.

Actual Test Value:


Characteristic for Test: Seismic Condition B

Acceptance Criteria: Maintain Pressure Boundary After Seismic Event. W-441 -P4, Rev. 2, Appendix L, page L-12, provides a seismic testing plan for these components at a (TBD) seismic spectra. "Confinement" leakage acceptance criteria is < 10-4 scclsec. Sample Size*: Seismic Testing is being performed for PT-1 *OS (CGl-SNF-D-07-P4-010). Both instruments are Baratron Series 400 and have identical pressure boundaries. Destructive testing of of PT-1 *OS will provide verification of the critical characteristics for this component.

Actual Test Value:


Characteristic for Test: Acceptance Criteria: . Sample Size*:

Actual Test Value:


Characteristic:

Acceptance criteria:

Sample Size*:

Actual Test Value:


Test Plan and Report #: References (see Section 7):

**lf SuppliedManufacturer or Other, Refer to CGI Checklist-2 for Support Information

12/21/98

Rev. No. 0 Commercial Grade Item Upgrade Dedication Form Page 12of 12

S N F - 3 8 9 2 ECNNo. NA CGI NO. CGESNF-D-13-P4-019 Title: MKS BARATRON MCO ABSOLUTE PRESSURE TRANSMITTER

SechonG ContactsrPhe Numbers 1 Name Phone I

Design Authority 0 I QA 0 I oc 0 I

[ ] DesignCalculations

[ ] Installation Instructions

[ ] Operation Instructions

I 1 Calibration Instructions

I 1 Mannfacturer’s Recommended Suare Parts List I I [ ] Other:

Procurement Documents

[ ] Certificate of ConformanceKompliance

I 1 Seismic Qualification Certificate

I 1 EnvironmentaI Onalification Certificate I I [ ] Test Report (s):

[ ] Inspection Report (s):

[

[

I 1 WeldRecords

] CMTRs for ASME Pressure Retaining Materials

] Valve Seat Leakage Report

I 1 Material Traceabilitv Record I I

12/21/98