77a76 classic american style twist pen kit instructions classic american style twist pen kit... ·...
TRANSCRIPT
“O”
From Setup To Sanding: These are the supplies we suggest you have on hand to com-
plete this pen kit:
� Letter “O” Pen Maker’s Bit
� 2 - 3⁄4" x 3⁄4" x 23⁄16" Pen Blanks
� Pen Mandrel
� Classic American Style Bushings (06R07)
� Thick CA or 5-Minute Epoxy
� Drill or Drill Press
� Sandpaper/Micro-Mesh
� Barrel Trimmer
� Pen Press
� Eye & Ear Protection
� Dust Mask
Cutting & Drilling Blanks: Note: Additional length has been
added to the overall length of the
blank to accommodate for squaring
the ends of the blank.
Gluing Blanks to Tubes: Rough the entire surface of the tube using 180-grit paper.
Next, using either a thick CA or 5-Minute Epoxy, apply adhe-sive to both the tube and the inside of the blank. To secure the brass tube into the inside of the blank make sure to rotate the tube as you insert it into the blank. This will help ensure even coverage of the adhesive and a much more secure bond.
Squaring the Blank to Length: When squaring the blanks to length work only to the brass.
Removing brass will affect the overall length of the blank
which is critical to the proper operation of the pen.
Mandrel Preparation:
Turning & Finishing the Blanks: The Body diameter must match exactly to the .396" diameter
bushing. If this diameter is not precisely obtained, the Cap
and Body will not operate properly, causing them to bind.
Once the upper barrel has been turned down to the proper
diameter a portion of the Cap must be
parted off for the pen assembly pro-
cess. Measure up from the bottom of
the Cap Blank 1/8" and make a mark.
remove the material to the brass, taking
care not to damage the brass tube. If
77A76
8/28/2015 Product : #123360, #144869, #148718, Product : #123360, #144869, #148718, Product : #123360, #144869, #148718, Product : #123360, #144869, #148718,
#123108, #123109, #147076, #148780#123108, #123109, #147076, #148780#123108, #123109, #147076, #148780#123108, #123109, #147076, #148780 Classic American Style
Twist Pen Kits
Woodcraft, 406 Airport Industrial Park, P.O. Box 1686, Parkersburg, WV 26102-1686
• 2014 by Woodcraft Supply, LLC. “Helping You Make Wood Work” is a registered trademark of Woodcraft Supply, LLC.
.396" .396"
23⁄16"
“O”
Drill
3⁄4" 2- Blanks
.496"
Sand
Body Cap
3⁄4"
.496"
1⁄8"
necessary clean any remaining material/glue from the tube
prior to assembly.
With the lathe spinning, begin sanding with 120-grit paper
and progress through the finer grits finishing at 320-grit. Once
finished with sanding apply a finish of your choice.
Pen Assembly:
Cap: � Press the Finial Clip Bushing (I) tapered end first, flush into
the .496" diameter, non-tenon end of the Finished Cap (H).
� Assemble the Center Band (G) which consists of three
pieces (G1, G2, G3). Once assembled, press onto the brass
tenon created during the turning process. If the Center Band
(G) is loose, we recommend carefully gluing it into place with
a small drop of CA glue.
Body: � Press Nib (A) into tapered end of the Nib Holder (B).
� Next slide the Accent Band (C) onto the post of the Nib
Holder (B). If assembling a Woodcraft Gold kit the Accent
Band will consist of three pieces (C1, C2, C3) that will need to
be assembled as shown in the above image.
� Press the Nib Assembly (A, B, C) into one end of the .396"
diameter end of the Finished Body (D).
� Press the Twist Mechanism Holder (E) into the opposite
end of the .396" diameter end of the Finished Body (D).
� Slide Spring (L) small end first onto the Ink Refill (M).
� Insert the Ink Refill (M) through the opening of the Twist
Mechanism Holder (E).
� Place the Twist Mechanism (F) over the Ink Refill (M) and
thread onto the Twist Mechanism Holder (E).
� Insert the threads of the Finial (K) through the opening of
Clip (J) and thread into the Finial Clip Bushing (I).
� To complete the assembly use a clamp or vise that will
open at least 6". Place the Finished Cap (H) over the end of
the Twist Mechanism (F) and align the wood grain or pattern
if necessary. Press the two halves together. This process will
join the Finial Clip Bushing (I) and the Twist Mechanism (F)
securing the two halves. If the pen top has not been secured
to the bottom, unthread the Finial (K) leaving approximately 1/16" gap and press again until the Finial is flush. This action
will further seat the Finial Clip Bushing (I) and engage the
Twist Mechanism (F).
77A76
8/28/2015 Product : #123360, #144869, #148718, Product : #123360, #144869, #148718, Product : #123360, #144869, #148718, Product : #123360, #144869, #148718,
#123108, #123109, #147076, #148780#123108, #123109, #147076, #148780#123108, #123109, #147076, #148780#123108, #123109, #147076, #148780 Classic American Style
Twist Pen Kits
Woodcraft, 406 Airport Industrial Park, P.O. Box 1686, Parkersburg, WV 26102-1686
• 2014 by Woodcraft Supply, LLC. “Helping You Make Wood Work” is a registered trademark of Woodcraft Supply, LLC.
H
E C D A
G
B F
I
J
M
K
L
C1, C2, C3
G1, G2, G3
Woodcraft Gold
Kits Only