742 236 k

936.

3540

Sub

ject

to

alte

ratio

n. Input 4 x 7-16 female

Connector position Bottom

Adjustment 2x, Position bottommechanism continuously adjustable

Weight 14.6 kg

Wind load Frontal: 650 N (at 150 km/h)Lateral: 100 N (at 150 km/h)Rearside: 700 N (at 150 km/h)

Max. wind velocity 200 km/h

Packing size 1574 x 360 x 130 mm

Height/width/depth 1319 / 323 / 71 mm

Mechanical specifications

XXPol Panel 1710–2200/1710–2200 65°/65° 18/18dBi 0°–10°/0°–10°T

1710–2200–45°

1710–2200+45°

7-16 7-16

1710–2200+45°

7-16

1710–2200–45°

7-16

2-Multi-band PanelDual PolarizationHalf-power Beam WidthAdjust. Electr. Downtiltset by hand or by optional RCU (Remote Control Unit)

1710–22001710–2200

XX

65°65°

0°–10°0°–10°

742 236Type No.

Frequency range1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2200 MHz

Polarization +45°, –45°; +45°, –45° +45°, –45°; +45°, –45° +45°, –45°; +45°, –45°

Gain 4 x 17.6 dBi 4 x 17.8 dBi 4 x 18 dBi

Horizontal Pattern:

Half-power beam width 64° 64° 62°

Front-to-back ratio Copolar: > 30 dB Copolar: > 30 dB Copolar: > 30 dBTotal power: > 25 dB Total power: > 25 dB Total power: > 25 dB

Cross polar ratioMaindirection 0° Typically: 25 dB Typically: 25 dB Typically: 25 dBSector ±60° > 10 dB > 10 dB > 10 dB

Vertical Pattern:

Half-power beam width 7° 6.8° 6.5°

Electrical tilt 0°–10°, continuously adjustable

Sidelobe suppression for first 0° ... 5° ... 10° T 0° ... 5° ... 10° T 0° ... 5° ... 10° Tsidelobe above main beam 20 ... 18 .... 16 dB 20 ... 18 ... 16 dB 16 ... 18 ... 16 dB

Impedance 50 Ω

VSWR < 1.5

Isolation, between inputs > 30 dB

Intermodulation IM3 < –150 dBc (2 x 43 dBm carrier)

Max. power per input 300 W (at 50 °C ambient temperature)

1710–2200

Horizontal Pattern Vertical Pattern0°–10° electrical downtilt

64°130°

dB

10

3

0

dB

10

3

0

7°


10

3

0

64°125°

dB

1850 – 1990 MHz: +45°/–45° Polarization

6.8°

dB

10

3

0



10

3

0

62°120°

dB


6.5°

dB

10

3

0

742 236 of 4

KATHREIN-Werke KG . Anton-Kathrein-Straße 1 – 3 . P.O. Box 10 04 44 . 83004 Rosenheim . Germany . Phone +49 8031 184-0 . Fax +49 8031 184-973

Internet: www.kathrein.de

936.

3540

Sub

ject

to

alte

ratio

n.

Material: Reflector screen: Aluminum. Radiator: Tin-plated zinc.Flat fiberglass radome: The max. radome depth is only 71 mm. Fiber-glass material guarantees optimum performance with regards to stability,stiffness, UV resistance and painting. The colour of the radome is grey.All screws and nuts: Stainless steel.

Grounding: The metal parts of the antenna including the mounting kit and the innerconductors are DC grounded.

Environmental conditions: Kathrein cellular antennas are designed to operate under the environ-mental conditions as described in ETS 300 019-1-4 class 4.1 E. The antennas exceed this standard with regard to the following items:– Low temperature: –55 °C– High temperature (dry): +60 °C

Ice protection: Due to the very sturdy antenna construction and theprotection of the radiating system by the radome, the antenna remainsoperational even under icy conditions.

Environmental tests: Kathrein antennas have passed environmental tests as recommended in ETS 300 019-2-4. The homogenous design of Kathrein’s antennafamilies use identical modules and materials. Extensive tests have beenperformed on typical samples and modules.

6472

20

Adjustmentmechanism

with integrated scale

1319

1384

1529

9

1710–2200 Left

–45° –45°+45°

Right 1710–2200+45°

RCURCU

Layout of interface

48254

41 71 98

323

Bottom view

For downtilt mounting use the clamps for an appropriate mast diameter together with the downtilt kit.Wall mounting: No additional mounting kit needed.

Accessories (order separately)

738 546 1 clamp Mast: 50 – 115 mm diameter 1.0 kg 2



737 974 1 downtilt kit Downtilt angle: 0° – 16° 2.8 kg 1

Type No. Description RemarksWeight Units perapprox. antenna

AccessoriesGeneral Information

of 4 742 236



Please note: As a result of more stringent legal regulations and judgements regarding product liability, we are obliged to point out certain risks that may arise when products are used under extraordinary operatingconditions.

The mechanical design is based on the environmental conditions as stipulated in ETS 300 019-1-4 and therebyrespects the static mechanical load imposed on an antenna by wind at maximum velocity. Wind loads arecalculated according to DIN 1055-4. Extraordinary operating conditions, such as heavy icing or exceptionaldynamic stress (e.g. strain caused by oscillating support structures), may result in the breakage of an antenna or even cause it to fall to the ground. These facts must be considered during the site planning process.

The installation team must be properly qualified and also be familiar with the relevant national safetyregulations.The details given in our data sheets have to be followed carefully when installing the antennas andaccessories.The limits for the coupling torque of RF-connectors, recommended by the connector manufacturersmust be obeyed.

Any previous datasheet issues have now become invalid.

936.

3540

Sub

ject

to

alte

ratio

n.

742 236 of 4



Remove the protective cap. Set downtilt angle by rotating theadjustment wheel.

0° – max.°

max.° – 0°

Manual adjustment procedure:

General Instructionsfor Adjustment Mechanism

Description of the adjustment mechanism (protective cap removed):

➀ Adjustment wheel with twist-lockfunction.

➁ Downtilt spindle with integratedscale.

➀ Thread for fixing the protectivecap or the RCU (Remote ControlUnit).

➁ Gearwheel for RCU power drive.

2

12

1

To set the downtilt angle exactly,you must look horizontally at thescale. The lower edge of the gear-wheel must be used for alignment.

Optional: RCU (Remote Control Unit) for remote-controlled downtilt adjustment:

For a description of RCU installation please refer to the respective data sheet.

Screw on the protective cap again.

936.

3540

Sub

ject

to

alte

ratio

n.

of 4 742 236



General Instructions for Feederline Installation on Panels with four Connectorsarranged on two Levels

Please note: In order not to damage the interfaces, please make sure that only the right tools are used.Tighten the feederline connector interfaces solely by using a common torque-wrench with a suitable wrenchwidth.

Attachment of the feederline connector and RCU (optional):In order to protect the adjustment mechanism the protective caps have to be attached duringfeederline installation!

Start with the rearside located inter-face no. 1.

Place the connector carefully and fix thenut using a torque-wrench (according tothe manufacturers guidelines).

The further sequence for the installationis: feederlines no. 2, 3, 4.

After feederline installation the optionalremote control units (RCU) can bemounted if required.

For a full description of RCU installationplease refer to the respective data sheet.

Please note: Additional weather sealing of correctly installed feederline connector interfaces is not required,nor is it recommended by the connector manufacturers.

Description of connector arrangement:

There are four interfaces for feeding the antennalocated at the bottom.

The connectors are mounted at two levels in order to facilitate feederlineinstallation.

12

34

742 236 k

Documents