6210pto & 6210xt manual p.w. 10.30.2017.doc - 1 - salsco€¦ · 2) raise and lower till the...
TRANSCRIPT
O:\Manuals\6210..6210XT CHIPPER\6210PTO & 6210XT MANUAL P.W. 10.30.2017.doc - 1 -
O:\Manuals\6210..6210XT CHIPPER\6210PTO & 6210XT MANUAL P.W. 10.30.2017.doc - 2 -
TABLE OF CONTENTS
MODELS 6210PTO & 6210XT CHIPPER
COVER & TABLE OF CONTENTS…………………………………..……..….Pages 1 - 2
STATEMENT OF FACT …………………………………..…………..…….……… Page 3
SPECIFICATIONS & FEATURES ……………………..………………..……….Page 4 - 5
MACHINE REGISTRATION ………………………………………….....…….…….Page 6
SAFETY & OPERATING INSTRUCTIONS ………………………..…....…….Pages 7 – 9
HOW TO CUT A DRIVE SHAFT ………………………….………….………..…..Page 10
SERVICE & MAINTENANCE INSTRUCTIONS ………….………………..……..Page 11
TORQUE CHART. …………………………….……………..………………..……Pages 12
PARTS DIAGRAMS …………………………………….…….…....….………Pages 13 - 27
WARRANTY POLICY/PROCEDURE ………………………….….………..……...Page 28
COPY OF WARRANTY CLAIM FORM….……...…………….……...….………...Page 29
COPY OF DEALER DELIVERY REPORT & WARRANTY CARD………………Page 30
SERVICE SCHEDULE LOG ………………………………………....……………...Page 31
SALSCO, INC.
105 School House Rd., Cheshire, CT 06410
800-872-5726, 203-271-1682, 203-271-2596(Fax)
[email protected], www.salsco.com
O:\Manuals\6210..6210XT CHIPPER\6210PTO & 6210XT MANUAL P.W. 10.30.2017.doc - 3 -
STATEMENT OF FACT
You have just purchased the highest quality, most dependable, PTO Chipper, 6210 and 6210XT on
the market today. This unit has the ability to meet exact standards and perform for years with
minimum downtime. HOWEVER, it cannot read nor will it understand this manual no matter how
long you leave it on top of the machine.
It is your responsibility to read and understand this manual; it is also your responsibility to be
certain this information is passed along to anyone who is expected to operate this equipment.
Should you choose not to read, understand and pass along the information provided you, please
expect equipment failure and possible injuries to persons around this equipment.
For the safety of the operator, it is imperative that this manual is carefully read and understood.
Once you have read this manual, it is your responsibility to be sure that all new operators read and
understand this manual, especially all cautions stated.
As a manufacturer of equipment, we have a responsibility to design a safe piece of equipment.
NOTE: The important safeguards and instructions in this manual are not meant to cover all possible
conditions and situations that may occur. It must be understood that common sense, caution, and
care are factors, which cannot be built into any product. These factors must be supplied by the
person(s) caring for and operating this equipment.
ONLY YOU CAN PREVENT ACCIDENTS!!
O:\Manuals\6210..6210XT CHIPPER\6210PTO & 6210XT MANUAL P.W. 10.30.2017.doc - 4 -
O:\Manuals\6210..6210XT CHIPPER\6210PTO & 6210XT MANUAL P.W. 10.30.2017.doc - 5 -
O:\Manuals\6210..6210XT CHIPPER\6210PTO & 6210XT MANUAL P.W. 10.30.2017.doc - 6 -
MACHINE REGISTRATION
MANUFACTURED BY: SALSCO, INC.
105 School House Rd., Cheshire, CT 06410
800-872-5726, 203-271-1682, 203-271-2596 (Fax)
[email protected] www.salsco.com
THIS MANUAL COVERS MODEL (s): 6210PTO and MODEL 6210XT CHIPPERS
This company reserves the right to discontinue, add improvements to, or change the design of any model
or product at any time without obligation to improve existing machines, either by changing the design or
adding new parts.
It has been and will continue to be the policy of SALSCO to update existing machines at its own
discretion. Whenever possible, new designs will be made in such a way that they can be "Retro Fit" if so
desired.
Record in the space provided below the model and serial number of this unit. Please retain these
numbers for future reference.
No parts orders will be accepted WITHOUT MODEL NUMBERS OR PART NUMBERS. All part
numbers are listed in this manual.
_____________________________________________ ___________________
Serial Number Model Number
NOTE: Be sure to complete your warranty card. This will insure immediate processing of any warranty
claims.
READ AND UNDERSTAND THIS MANUAL BEFORE STARTING THE MACHINE
1/06
O:\Manuals\6210..6210XT CHIPPER\6210PTO & 6210XT MANUAL P.W. 10.30.2017.doc - 7 -
CAUTIONS
READ THOROUGHLY THE OPERATOR SAFETY INSTRUCTIONS ON THE FOLLOWING THREE
PAGES, WHICH ARE THE AMERICAN NATIONAL STANDARD OF POWERED
SHREDDERS/GRINDERS, SAFETY SPECIFICATIONS PROVIDED BY ANSI AND THE O.P.E.I.
THE FOLLOWING CAUTIONS ARE PROVIDED BY SALSCO AS A QUICK REFERENCE ONLY
AND ARE NOT MEANT TO REPLACE THE PRECAUTIONS ON THE FOLLOWING PAGES.
1. ALWAYS use protective eyewear when machine is in operation.
2. ALWAYS use gloves and wear ear protection when machine is in operation.
3. NEVER put hands, legs or any part of your body into or near Chipper intake or discharge openings.
4. NEVER run machine with guards or shaft cover removed.
5. ALWAYS allow machine to cool off, BE SURE machine has stopped completely, and disconnect drive
shaft from tractor before attempting any maintenance, or repair.
6. NEVER stand in front of chipper infeed hopper. It is possible for a chip or piece of wood to be thrown
out.
7. BE SURE the machine and tractor is parked on a dry level surface before starting operation.
8. DO NOT operate with loose clothing or long unrestrained hair. Be sure vines and branches are not
wrapped around your body parts.
9. DO NOT operate on ice or any other slippery surface. Be sure area around machine is clear and clean.
You do not want to trip into the machine.
10. NEVER leave machine running unattended, especially around youngsters or persons not instructed in
the safe operation of this machine.
11. READ and understand federal guidelines provided with this manual.
NEVER run machine without connecting the 3-point to the tractor!
O:\Manuals\6210..6210XT CHIPPER\6210PTO & 6210XT MANUAL P.W. 10.30.2017.doc - 8 -
BRUSH CHIPPERS
ANSI Z133.1-2006 American National Standard for Arboricultural Operations
Safety Requirements
O:\Manuals\6210..6210XT CHIPPER\6210PTO & 6210XT MANUAL P.W. 10.30.2017.doc - 9 -
BRUSH REMOVAL AND CHIPPING
ANSI Z133.1-2006 American National Standard for Arboricultural Operations
Safety Requirements
O:\Manuals\6210..6210XT CHIPPER\6210PTO & 6210XT MANUAL P.W. 10.30.2017.doc - 10 -
HOW TO CUT A DRIVE SHAFT
1) Attach the implement to the tractor. Raise and lower it, BE SURE it's angle is correct and there is
nothing hitting.
2) Raise and lower till the stub PTO shaft on the tractor and the implement are the closest to each other
they can be.
3) Take a measurement TIP TO TIP on the stub shafts. EXAMPLE: Let's say 28" tip to tip is the measurement
you made.
4) Lay the drive shaft on the bench. Close it ALL THE WAY and measure from inside of each yoke to the other.
Don't forget the yoke must fit over the stub shaft. That's why you measure from inside the yoke. EXAMPLE:
Let's say the drive shaft is 60" from yoke to yoke when it's in its most closed state.
28" is what we want!
60" is what we have!
Take 60"- 28" = 32" from each side
THAT'S THE AMOUNT THAT SHOULD BE CUT FROM EACH HALF OF THE DRIVE SHAFT.
5) NOTES: To remember
A - DON'T forget the yoke must fit over the stub shaft.
B - You can cut it again EASIER than you can add.
SAFETY FIRST – ALWAYS WEAR PROTECTIVE GEAR
WHEN WORKING WITH/ON, EQUIPMENT/TOOLS!
O:\Manuals\6210..6210XT CHIPPER\6210PTO & 6210XT MANUAL P.W. 10.30.2017.doc - 11 -
6210PTO & 6210XT
SERVICE SCHEDULE
1. Whenever service is to be done to a PTO implement, be sure to disconnect the drive shaft.
2. GREASE all bearings daily. DO NOT OVER GREASE. Wipe extra grease off bearings.
3. To sharpen blades: Remove hopper or open door (depending on which model machine). Remove blades
and replace with sharpened ones. It is recommended that you replace the hardware whenever replacing
blades. Be sure to follow the torque specifications in your manual. Be sure to clean mounting surface before
bolting on new blades. Be sure to use Locktite when replacing hardware.
4. Bed knife adjustment: This adjustment varies from 1/16” to 1/4”. The larger the opening, between bed
knife and chip blades, the faster the wood will feed and the harder the machine will have to work. The
smaller the opening, the slower it will feed and the less work the machine will have to do. We recommend
1/8” to 3/16”.
5. Be sure you double-check all nuts and bolts for tightness. A loose bolt can cause total destruction of the
machine.
6. Keep machine clean and free from dirt.
SERVICE SCHEDULE AS
NEEDED
DAILY WEEKLY
CLEAN MACHINE
GREASE DISC SHAFT
BEARING
SHARPEN CHIPPER BLADES
CHECK & ADJUST BED
KNIFE
CHECK ALL NUTS & BOLTS
X
X
X OR
X OR
X
X
X
X
X
X
NEVER, UNDER ANY CIRCUMSTANCES, RUN THE WHEN UNIT IT IS OPEN OR AT ANY TIME
DURING SERVICE OR ROUTINE MAINTENANCE.
O:\Manuals\6210..6210XT CHIPPER\6210PTO & 6210XT MANUAL P.W. 10.30.2017.doc - 12 -
BOLT SIZE Thds Per Inch SAE Grade 5 SAE Grade 8
¼ 20
28
10
---
14
---
5/16 18
24
19
---
29
---
3/8 16
24
33
---
47
---
7/16 14
20
54
---
78
---
½ 13
20
78
---
119
---
9/16 12
18
114
---
169
---
5/8 11
11
154
---
230
---
¾ 10
10
257
---
380
---
7/8 9
9
382
---
600
---
1 8
8
587
---
700
---
Below is a quick reference chart for various “Flat Head
Cap Screws” and the torque recommendations.
VALUES ARE STATED IN FOOT POUNDS
O:\Manuals\6210..6210XT CHIPPER\6210PTO & 6210XT MANUAL P.W. 10.30.2017.doc - 13 -
O:\Manuals\6210..6210XT CHIPPER\6210PTO & 6210XT MANUAL P.W. 10.30.2017.doc - 14 -
O:\Manuals\6210..6210XT CHIPPER\6210PTO & 6210XT MANUAL P.W. 10.30.2017.doc - 15 -
O:\Manuals\6210..6210XT CHIPPER\6210PTO & 6210XT MANUAL P.W. 10.30.2017.doc - 16 -
O:\Manuals\6210..6210XT CHIPPER\6210PTO & 6210XT MANUAL P.W. 10.30.2017.doc - 17 -
O:\Manuals\6210..6210XT CHIPPER\6210PTO & 6210XT MANUAL P.W. 10.30.2017.doc - 18 -
O:\Manuals\6210..6210XT CHIPPER\6210PTO & 6210XT MANUAL P.W. 10.30.2017.doc - 19 -
O:\Manuals\6210..6210XT CHIPPER\6210PTO & 6210XT MANUAL P.W. 10.30.2017.doc - 20 -
O:\Manuals\6210..6210XT CHIPPER\6210PTO & 6210XT MANUAL P.W. 10.30.2017.doc - 21 -
O:\Manuals\6210..6210XT CHIPPER\6210PTO & 6210XT MANUAL P.W. 10.30.2017.doc - 22 -
O:\Manuals\6210..6210XT CHIPPER\6210PTO & 6210XT MANUAL P.W. 10.30.2017.doc - 23 -
O:\Manuals\6210..6210XT CHIPPER\6210PTO & 6210XT MANUAL P.W. 10.30.2017.doc - 24 -
O:\Manuals\6210..6210XT CHIPPER\6210PTO & 6210XT MANUAL P.W. 10.30.2017.doc - 25 -
O:\Manuals\6210..6210XT CHIPPER\6210PTO & 6210XT MANUAL P.W. 10.30.2017.doc - 26 -
- 27 -
- 28 -
- 29 -
WARRANTY POLICY
Please remember to complete and return your Warranty Card and Dealer Delivery Report. Warranty Claims will not be considered if the Warranty Card and Dealer Delivery Report have not been returned to Salsco.
Your Salsco Commercial or Turf Equipment product is a commercial type product and is normally manufactured and sold for commercial or
industrial use. Salsco will, for the original purchaser, for one (1) year from the date of purchase (90 days if used for rental purposes)
repair or replace, free of charge, any SALSCO part or parts found to be defective in material, workmanship or both. Any transportation
or shipping charges will be borne by the purchaser. If, during the warranty period stated above, the product does not function properly due to
defect, simply contact Salsco and follow the Warranty Procedures included in this manual.
This warranty does not include:
Incidental or consequential damages and is exclusive of any implied warranties. Normal maintenance parts, including, but not limited to hoses, chains, belts, filters, lubricants, etc.
Parts or components, which are covered under the original manufacturer warranty, including, but not limited to engines, pumps, and
motors.
WARRANTY PROCEDURE
In order for Salsco to consider your warranty claims in a timely manner you must follow the simple procedures listed below:
MACHINE OR PART FAILURE
a) Call our service department for helpful instruction on how to correct or repair the problem. Preventive maintenance will also be suggested.
b) When ordering parts for Warranty issues, you MUST retain possession of the old parts in question until notified with respect to returning the
parts to Salsco or other disposition.
c) Warranty Claims MUST be filed within 30-days from completion of the work performed. Contact our office for an electronic warranty claim
form.
d) Fill in all information requested on warranty claim form, a copy of which is included in this manual, (date of purchase, company name,
address, etc.). List all parts used. Make sure part numbers are correct. You can obtain these from your manual. (include good description of
problem; i.e. “leaking from spool” rather than “leaking”).
e) It is our goal to consider and reach a disposition on each Warranty Claim within 30-days from the date that it is received. Therefore it is
important that you respond promptly to any request for further information. Claims with no response to inquiries will be closed as “denied
for lack of response” 90-days from the date of request.
f) Email, Fax or Send Warranty Claim form to our Warranty Department. – Warranty on parts most often requires return of the parts that
were replaced. DO NOT DISCARD OLD PARTS UNTIL YOU HAVE RECEIVED A DETERMINATION AS TO WHETHER THESE
PARTS MUST BE RETURNED.
g) Our Warranty Department will contact and instruct you on how to return the Parts to Salsco on an RA #. Returns MUST be made within 30-
Days from issuance of RA #. FREIGHT CHARGES ON RETURN OF PARTS IS THE RESPONSIBILITY OF THE CUSTOMER.
Normal pre-delivery adjustments are not covered under warranty. Labor Warranties are based on reasonable time allowances as determined
by Salsco, Inc. and paid at 75% of posted labor rate. TRAVEL TIME IS NOT REIMBURSED UNDER THE WARRANTY POLICY.
h) Be sure to put the RA form inside the box that you are shipping back, also be sure to put on the outside of the box “Return of Goods” and the
RA #.
i) Ship returns via a traceable method such as UPS Ground Service. Be sure that the shipment is insured for the appropriate value. If uninsured
parts are lost, we cannot issue a credit.
PLEASE NOTE: Warranty forms should be filled out completely. PREVENTIVE MAINTENANCE IS YOUR BEST INSURANCE AGAINST EQUIPMENT FAILURE. BE SURE TO READ THIS
MANUAL, ESPECIALLY THE MAINTENANCE, OPERATING AND CAUTION SECTIONS.
SALSCO, INC., 105 School House Rd. Cheshire, CT 06410 800-872-5726, 203-271-1682 203-271-2596 (Fax) [email protected], www.salsco.com
- 30 -
- 31 -
- 32 -