5ce23d01

8/2/2019 5CE23d01

1/23

QUICK START GUIDEQUICK START GUIDE

Whats in the delivery?

Getting started

The first steps

PC utility software

Document no.: 4189340603A

SW version 3.0X.X or later

Generator Paralleling Controller, GPC-3Generator Protection Unit, GPU-3/GPU-3 Hydro

Paralleling and Protection Unit, PPU-3

8/2/2019 5CE23d01

2/23

GPC-3/GPU-3/GPU-3 Hydro/PPU-3 Quick Start Guide

DEIF A/S Page 2 of 23

Table of contents

1. ABOUT THIS DOCUMENT .................................................................................................... 3GENERAL PURPOSE ...................................................................................................................... 3INTENDED USERS.......................................................................................................................... 3CONTENTS/OVERALL STRUCTURE.................................................................................................. 3

2. WARNINGS AND LEGAL INFORMATION ........................................................................... 4LEGAL INFORMATION AND RESPONSIBILITY..................................................................................... 4ELECTROSTATIC DISCHARGE AWARENESS ..................................................................................... 4SAFETY ISSUES ............................................................................................................................ 4DEFINITIONS ................................................................................................................................ 4

3. WHATS IN THE DELIVERY? ............................................................................................... 5STANDARD DELIVERY.................................................................................................................... 5OPTIONAL DELIVERY ..................................................................................................................... 6

4. GETTING STARTED .............................................................................................................. 8CONNECTING THE DEVICES ........................................................................................................... 8BASIC WIRING FOR GPU-3 AND GPU-3HYDRO ........................................................................... 10BASIC WIRING FOR GPC-3 AND PPU-3 ....................................................................................... 12

5. THE FIRST STEPS .............................................................................................................. 14BASIC AC VALUES ...................................................................................................................... 14

6. PC UTILITY SOFTWARE .................................................................................................... 17INSTALLATION............................................................................................................................. 17GETTING CONNECTED WITH THE UNIT .......................................................................................... 18READ PARAMETERS FROM THE DEVICE ........................................................................................ 19BASIC CONFIGURATION OF A DEVICE USING THE UTILITY SOFTWARE.............................................. 20

7. CONFIGURING THE SPEED GOVERNOR AND AVR OUTPUTS ..................................... 21

8/2/2019 5CE23d01

3/23



1. About this documentGeneral purpose

This document is the Quick Start Guide for the Multi-line 2 GPC (Generator ParallelingController), GPU (Generator Protection Unit) and PPU (Paralleling and Protection Unit). Thedocument mainly includes general product information, mounting instructions and wiringdescriptions.

The general purpose of this Quick Start Guide is to help the user with the first steps of installingand using the unit.

Intended users

This Quick Start Guide is mainly intended for the panel builder in charge. On the basis of thisdocument, the panel builder designer will give the electrician the information he needs in order toget started to install the unit. For detailed electrical drawings, the Installation Instructions mustbe used.

Contents/overall structure

This document is divided into chapters, and in order to make the structure simple and easy touse, each chapter will begin from the top of a new page.

Please make sure that you also read the Installation Instructions beforestarting to work with the Multi-line 2 controller and the gen-set to becontrolled. Failure to do this could result in human injury or damage to theequipment.

8/2/2019 5CE23d01

4/23



2. Warnings and legal information

This chapter includes important information about general legal issues relevant in the handlingof DEIF products. Furthermore, some overall safety precautions will be introduced andrecommended. Finally, the highlighted notes and warnings, which will be used throughout thisdocument, are presented.

Legal information and responsibility

DEIF takes no responsibility for installation or operation of the generator set. If there is any doubtabout how to install or operate the generator controlled by the unit, the company responsible forthe installation or the operation of the set must be contacted.

Electrostatic discharge awareness

Sufficient care must be taken to protect the terminals against static discharges during theinstallation. Once the unit is installed and connected, these precautions are no longer necessary.

Safety issues

Installing the unit implies work with dangerous currents and voltages. Therefore, the installationof the unit should only be carried out by authorised personnel who understand the risks involvedin the working with live electrical equipment.

Definitions

Throughout this document a number of notes with helpful user information will be presented. Toensure that these are noticed, they will be highlighted in order to separate them from the generaltext.

Note symbol

Warnings

Be aware of the hazardous live currents and voltages. Do not touch any ACmeasurement inputs as this could lead to injury or death.

The notes provide general information which will be helpful for the reader to

bear in mind.

The warnings indicate a potentially dangerous situation which could result indeath, personal injury or damaged equipment if certain guidelines are notfollowed.

The units are not to be opened by unauthorised personnel. If opened anyway, thewarranty will be lost.

8/2/2019 5CE23d01

5/23



3. Whats in the delivery?

Standard delivery

The main unit

Standard display unit, DU-2

Layout is option dependent.

Display cable, 3m Installation Instructions

8/2/2019 5CE23d01

6/23



Optional delivery

Display cable with plugs, 6m (option J2)

PC cable for option N programming - Ethernet cable crossed (option J4)

Display cable with plugs, 1m (option J6)

PC cable for utility software (option J7)

8/2/2019 5CE23d01

7/23



Additional standard display, DU-2 (option X2)

Display unit, DU-2 DC/DC converter 2 x CANbus cable 3m

Layout is option dependent.

Additional operator panel, AOP-1 (option X3)

AOP-1 0.5m cable

Additional operator panel, AOP-2 (option X4)

AOP-2 DC/DC converter 2 x CANbus cable 3m

8/2/2019 5CE23d01

8/23



4. Getting started

Connecting the devices

Connecting the display with the main unit

Connect the SUB-D display cable to the main unit and the display unit as shown in the belowpicture.

Connecting the power supply to the main unit

Terminal 1: +24V DC

Terminal 2: 0V DC

787776757473 96 979594929190 938988878586838482818079

7271697068676566626359 60 6 15856575553 54 645251504947464443 45 4841403837 39 42

Service port DisplayPMS CAN

Engine CAN

Power

Self check ok

Alarm inhibit

Option M4

Terminal 98: +24V DC

Terminal 99: 0V DC

8/2/2019 5CE23d01

9/23



Connecting the additional operator panel, AOP-1 (optional)

Connecting the additional operator panel, AOP-2 (optional)

The CAN cable for the CANbus communication between the display unit of main unit no.1 and theAOP-2 has to be connected to the CAN port (CAN 2) of the display unit (DU-2) and the CAN port(CAN 1) of the AOP-2 as shown in the below drawing.

The AOP-2 can be placed up to 200m from the main display. The AOP-2 requires a separatepower supply unit, while the display receives the power supply through the display cable from themain unit.

For further information about the installation of multiple displays and AOP-2s,please refer to the document Description of Option X.

AOP-1 cable0.5m

Display unit,DU-2

AOP-1

8/2/2019 5CE23d01

10/23



Basic wiring for GPU-3 and GPU-3 Hydro

AC wiring

8/2/2019 5CE23d01

11/23



DC wiring

8/2/2019 5CE23d01

12/23



Basic wiring for GPC-3 and PPU-3

AC wiring

For further information, please refer to the document Installation Instructions.

8/2/2019 5CE23d01

13/23



DC wiring

8/2/2019 5CE23d01

14/23



5. The first steps

Basic AC values

This chapter guides you through the most essential parameters which have to be adjustedbefore you can start using the unit.

The setpoints can either be adjusted from the display unit or by using the DEIF utility software.The following examples will show how to adjust the parameters from the display unit.

All settings are reached by placing the cursor under SETUP (in the main page) and pressingENTER.

Place the cursor under SYST and press ENTER.

8/2/2019 5CE23d01

15/23



Place the cursor under GEN and press ENTER.

Place the cursor under the setting you require and press ENTER.

8/2/2019 5CE23d01

16/23



Generator nominal settings 1

No. Setting Min.

Max.

Factory

setting

Notes Ref. Description

6000 Nominal settings 1

6001 Nom. settings 1 Frequency 48.0Hz62.0Hz

50.0Hz DesignersReference

Handbook

The selection ofnominal settings to be

used is set in 6006. A

binary input or selection

in M-logic can also be

used.

The range of nom.

voltage and nom.

power depends on the

selected range in 9030

Scaling.

6002 Nom. settings 1 Power10kW

20000kW480kW

6003 Nom. settings 1 Current0A

9000A867A

6004 Nom. settings 1 Voltage100V

25000V400V

6005 Nom. settings 1 RPM100 RPM

4000 RPM1500 RPM

6006 Nom. settings 1 Set1

41

To adjust the transformer settings, use the or push-button to get to the transformerpage.

VT and CT settings

No. Setting Min.

Max.

Factory

setting


6040 G transformer

6041 G transformer U primary100V

25000V400V

Designers

Reference

Handbook

If no voltage

transformer is present,

the primary and

secondary side values

are set to generatornominal value.

6042 G transformer U secondary100V

690V

400V

6043 G transformer I primary5A

9000A1000A

6044 G transformer I secondary1A

5A5A

6050 Busbar settings

6051 BB settings U primary100V

25000V400V

Designers

Reference

Handbook

If no voltage

transformer is present,

the primary and

secondary side values

are set to generator

nominal value.

6052 BB settings U secondary100V

690V400V

6053 BB settings U BB nom.100V

25000V400V

8/2/2019 5CE23d01

17/23



6. PC utility software

Installation

1. Go to www.deif.com2. Select Download centre3. Select Software download4. Select Multi-line 2 utility software V.3.X in the dropdown menu5. Fill in your e-mail address and click Submit.

Subsequently you will receive an e-mail containing a link. Click the link and follow theinstructions.

The USW is now installed on your computer.

Installation of USB drivers

On Windows Vista machines, the USB drivers are installed automatically.

This is the procedure on Windows XP machines:

When you connect the DEIF product, Windows XP will launch two Hardware Wizards. Twodrivers are installed, so please let Windows execute both Found new Hardware Wizard.

We recommend letting the Hardware Wizard install the software automatically by choosing theRecommended option. If the Advanced option is chosen, the needed files are available fromthe USW3 installation folder (default: C:\Program Files\DEIF\USW3\) in the USB driverfiles/source PreInstaller folder.

Please select Continue Anyway if a Hardware Installation warning (see figure below) appearsduring the installation.

8/2/2019 5CE23d01

18/23



Getting connected with the unit

Connect the service port to the USB on the computer (option J7 or option J3).

Click the Utility Software 3 icon on the desktop or in the Windows Start menu.

Desktop icon: Quick launch and Start menu icon:

Utility Software 3.lnk

The below window appears.

Open Windows devicemanager.

Check the COM portused for communi-cation, and make surethe settings corres-

pond to the applicationsettings.

Open the applicationsettings by clicking thisicon.

Click the Connect icon.

8/2/2019 5CE23d01

19/23



Read parameters from the device

After retrieving all the parameters, the device is ready to be configured.

Open the Parameterslist.

Click the Readparametersicon.

8/2/2019 5CE23d01

20/23



Basic configuration of a device using the utility software

When the parameters have been uploaded, the below options will be available.

The parameters can be configured as follows.

Click a parameter, and the below dialogue box will appear.

The parameter setpoint has now been changed and downloaded to the device.

For further information, please refer to the document General Guidelines forCommissioning.

Click this or use thebar to adjust thesetpoint, and thenclick Write and OK.

Click the Gentab.

8/2/2019 5CE23d01

21/23



7. Configuring the speed governor and AVR outputs

Dependent on the hardware configuration, relays or analogue outputs can be used for speedgovernor and AVR control.

The settings used for this are the following:

No. Setting Min.

Max.

Factory

setting


2600 Relay control

2601 Relay control GOV ON time10 ms

6500 ms500 ms

Designers

Reference

Handbook

GPU:

Option G2

This menu is only

available if Relay

is selected in

menu 2781.

2602 Relay control GOV periodtime

50 ms32500 ms

2500 ms Normally used:Relay 65 for

increase and relay

67 for decrease.2603 Relay control Increase relayNot used

Option dep.Relay 65

2604 Relay control Decrease relayNot used

Option dep.Relay 67

2720 Relay control (AVR)

2721 Relay control AVR ON time10 ms

3000 ms100 ms

Option:

AVR control

(D1)

Relay outputs for

voltage/VAr/power

factor control.

This menu is only

available if Relay

is selected in

menu 2782.

Normally used:

Relay 69 for

increase and relay

71 for decrease.

2722 Relay control AVR per time50 ms

1500 ms500 ms

2723 Relay control U increaseNot used

Option dep.Relay 69

2724 Relay control U decreaseNot used

Option dep.Relay 71

2780 Regulator output

2781 Reg. output GOVRelay

EICRelay

Designers

Reference

Handbook

GPU:

Option G2

Selection of the

speed output:

Relay, analogue

or engine

interface

communication.

Analogue and EIC

are optiondependent.

2782 Reg. output AVRRelay

AnalogueRelay

Option:

AVR control

(D1)

Generator voltage

control based on

relay or analogue

output signals.

Analogue

selection is only

available if option

E1, E2, EF2, EF4

or F2 is present.

8/2/2019 5CE23d01

22/23



No. Setting Min.

Max.

Factory setting Notes Ref. Description

5980 Governor output

5981 Governor output Output A

Disabled

AO66AO71 Disabled

Option E

and F

Normally used:

Analogue output66

5990 AVR output

5991 AVR output Output A

Disabled

AO66

AO71

Disabled

Option D Normally used:

Analogue output

71

AVR control requires option D1.

Analogue outputs require option E1, E2, EF2, EF4 or EF5.

For further information, please refer to the document General Guidelines forCommissioning.

8/2/2019 5CE23d01

23/23



For further information, please check the following documents:

GPC-3 Designers Reference Handbook Document no. 4189340587GPU-3 Designers Reference Handbook Document no. 4189340584GPU-3 Hydro Designers Reference Handbook Document no. 4189340588PPU-3 Designers Reference Handbook Document no. 4189340583

GPC-3/GPU-3/GPU-3 Hydro/PPU-3 Installation Instructions Document no. 4189340582GPC-3/GPU-3/GPU-3 Hydro/PPU-3 Operators Manual Document no. 4189340579

DEIF A/S reserves the right to change any of the above.

5ce23d01

Documents