-4gb sd memory card - p/n otch550881 -ac adapter - p/n … · 2019. 11. 11. · mvciw as de. using...

15
11/10/2019 01-023 • Updating Control Units/Modules (Revised 05/15/2009) • 2002 Honda Civic • MotoLogic https://www.motologic.com/car/0b2cd630-3db7-012c-0340-19005f6e69db/article/03827370-5489-012c-1ea7-001b2106f1f9?returnPath=%2Fcar%2F… 1/15 Report a problem with this article Service Bulletin 01-023 April 10, 2010 Honda Vehicles With Programmable Control Units/Modules Applies To: Updating Control Units/Modules (Supersedes 01-023, dated May 15, 2009, to revise the information marked by the black bars) This service bulletin describes these subjects: REVISION SUMMARY Who to contact for questions or problems when Under REQUIRED TOOLS AND EQUIPMENT, the using Honda-supplied updating equipment or the iN MVCI was added. (pg. 1). Under UPDATING TIPS AND PRECAUTIONS, MVCI information was added. Required Tools and Equipment - MVCI (pg. 2) UPDATING WITH THE MVCI was added. - GNA600 (pg. 2) - HDS Tablet (pg. 3) The procedures in this service bulletin are used - HDS Pocket Tester (pg. 3) and referenced in other service bulletins. - HIM (pg. 3) Most 2002 and later Hondas have reprogrammable Updating Tips and Precautions (pg. 3) control units/modules. To update (reprogram) any of Updating with the MVCI (pg. 5) these control units/modules, you need the vehicle you’re working on and one of these systems: Updating with the GNA600 MVCI unit with latest control module (CM) update - GNA600 Updating in Pass-Thru Mode (pg. 7) software installed - GNA600 Updating in Storage Mode (pg. 9) GNA600 gateway device and an iN workstation with the latest HDS software installed Updating with the HDS Tablet and the HDS Pocket Tester (pg. 10) HDS Tablet with the latest HDS software installed Updating with the HIM HDS Pocket Tester with the latest HDS software installed - HIM Updating in Pass-Thru Mode (pg. 12) - HIM Updating in Storage Mode (pg. 13) HIM and an iN workstation with the latest HDS software installed - Diagnosing HIM Error Codes (pg. 15) - HIM Self-Test (pg. 15) A compatible J2534 device and a PC with Honda's J2534 software installed NOTE: Whenever you install a new, reprogrammable control unit/module, check that it has the latest software, and update it if needed. WARRANTY CLAIM INFORMATION Skill Level: Repair Technician Refer to the specific service bulletin for the symptom you are repairing. QUESTIONS ABOUT THE UPDATING EQUIPMENT OR THE INTERACTIVE NETWORK For questions about the Honda-supplied updating equipment, call American Honda’s Special Tools hotline at 800-346-6327. For questions about the iN, call the iN Support Center at 800-245-4343. 1 of 15 © 2010 American Honda Motor Co., Inc. – All Rights Reserved ATB 22475-43652 (1004) CUSTOMER INFORMATION: The information in this bulletin is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely maintain your vehicle. These procedures should not be attempted by “do-it-yourselfers,” and you should not assume this bulletin applies to your vehicle, or that your vehicle has the condition described. To determine whether this information applies, contact an authorized Honda automobile dealer.

Upload: others

Post on 28-Nov-2020

1 views

Category:

Documents


0 download

TRANSCRIPT

Page 1: -4GB SD Memory Card - P/N OTCH550881 -AC Adapter - P/N … · 2019. 11. 11. · MVCIw as de. using Honda-supplied updating equipment or the iN •Under UPDATING TIPS AND PRECAUTIONS,

11/10/2019 01-023 • Updating Control Units/Modules (Revised 05/15/2009) • 2002 Honda Civic • MotoLogic

https://www.motologic.com/car/0b2cd630-3db7-012c-0340-19005f6e69db/article/03827370-5489-012c-1ea7-001b2106f1f9?returnPath=%2Fcar%2F… 1/15

Report a problem with this article

Service Bulletin 01-023April 10, 2010Honda Vehicles With Programmable Control Units/ModulesApplies To:

Updating Control Units/Modules(Supersedes 01-023, dated May 15, 2009, to revise the information marked by the black bars)

This service bulletin describes these subjects:REVISION SUMMARY• Who to contact for questions or problems when• Under REQUIRED TOOLS AND EQUIPMENT, the

using Honda-supplied updating equipment or the iNMVCI was added.(pg. 1).• Under UPDATING TIPS AND PRECAUTIONS,

MVCI information was added. • Required Tools and Equipment- MVCI (pg. 2)• UPDATING WITH THE MVCI was added.- GNA600 (pg. 2)- HDS Tablet (pg. 3)The procedures in this service bulletin are used - HDS Pocket Tester (pg. 3)and referenced in other service bulletins.- HIM (pg. 3)

Most 2002 and later Hondas have reprogrammable • Updating Tips and Precautions (pg. 3)control units/modules. To update (reprogram) any of

• Updating with the MVCI (pg. 5)these control units/modules, you need the vehicleyou’re working on and one of these systems: • Updating with the GNA600• MVCI unit with latest control module (CM) update

- GNA600 Updating in Pass-Thru Mode (pg. 7)software installed- GNA600 Updating in Storage Mode (pg. 9)• GNA600 gateway device and an iN workstation with

the latest HDS software installed • Updating with the HDS Tablet and the HDS PocketTester (pg. 10)• HDS Tablet with the latest HDS software installed

• Updating with the HIM• HDS Pocket Tester with the latest HDS softwareinstalled - HIM Updating in Pass-Thru Mode (pg. 12)

- HIM Updating in Storage Mode (pg. 13)• HIM and an iN workstation with the latest HDSsoftware installed - Diagnosing HIM Error Codes (pg. 15)

- HIM Self-Test (pg. 15)• A compatible J2534 device and a PC with Honda'sJ2534 software installed NOTE: Whenever you install a new, reprogrammable

control unit/module, check that it has the latestsoftware, and update it if needed.

WARRANTY CLAIM INFORMATIONSkill Level: Repair TechnicianRefer to the specific service bulletin for the symptomyou are repairing.

QUESTIONS ABOUT THE UPDATING EQUIPMENTOR THE INTERACTIVE NETWORKFor questions about the Honda-supplied updatingequipment, call American Honda’s Special Toolshotline at 800-346-6327.For questions about the iN, call the iN Support Centerat 800-245-4343.

1 of 15© 2010 American Honda Motor Co., Inc. – All Rights Reserved ATB 22475-43652 (1004)

CUSTOMER INFORMATION: The information in this bulletin is intended for use only by skilled technicians who have the proper tools, equipment,and training to correctly and safely maintain your vehicle. These procedures should not be attempted by “do-it-yourselfers,” and you should not assumethis bulletin applies to your vehicle, or that your vehicle has the condition described. To determine whether this information applies, contact anauthorized Honda automobile dealer.

Page 2: -4GB SD Memory Card - P/N OTCH550881 -AC Adapter - P/N … · 2019. 11. 11. · MVCIw as de. using Honda-supplied updating equipment or the iN •Under UPDATING TIPS AND PRECAUTIONS,

11/10/2019 01-023 • Updating Control Units/Modules (Revised 05/15/2009) • 2002 Honda Civic • MotoLogic

https://www.motologic.com/car/0b2cd630-3db7-012c-0340-19005f6e69db/article/03827370-5489-012c-1ea7-001b2106f1f9?returnPath=%2Fcar%2F… 2/15

GNA600:REQUIRED TOOLS AND EQUIPMENT(No longer available for purchase)NOTE: Updating for most control units/modules can be

done with any of the following tools.

MVCI:(Available through the Honda Tool and EquipmentProgram; call 888-424-6857)

• GNA600 KitNOTE: For more information on kit contents, refer tothe GNA600 User Guide on ISIS.- GNA600 Unit - P/N TDS35540400- PC USB Interface Cable - P/N TDS35525406- DLC Cable - P/N TDS35541433- Power Supply Unit - P/N TDS60678010- Power Supply Cord - P/N TDS35481214- Trigger Switch Adapter Block (Yellow) -

P/N TDS35541434- Trigger Switch - P/N TDS35541359

• iN Workstation

• MVCI KitNOTE: For more information on kit contents, refer tothe MVCI User Guide or Honda Tool and EquipmentProgram on ISIS.- MVCI Unit - P/N OTCH5528542- PC USB Interface Cable - P/N OTCH550421- OBD-II 16P Cable (DLC Cable) - P/N OTC3825-32- AC Adapter - P/N OTCH550207- 4GB SD Memory Card - P/N OTCH550881

2 of 15 01-023

Page 3: -4GB SD Memory Card - P/N OTCH550881 -AC Adapter - P/N … · 2019. 11. 11. · MVCIw as de. using Honda-supplied updating equipment or the iN •Under UPDATING TIPS AND PRECAUTIONS,

11/10/2019 01-023 • Updating Control Units/Modules (Revised 05/15/2009) • 2002 Honda Civic • MotoLogic

https://www.motologic.com/car/0b2cd630-3db7-012c-0340-19005f6e69db/article/03827370-5489-012c-1ea7-001b2106f1f9?returnPath=%2Fcar%2F… 3/15

HIM:HDS Tablet:• HIM - P/N TDS35570101P/N TDSGDS2200

(No longer available for purchase)(No longer available for purchase)

YELLOW REDLED LEDGREENLED

CABLE

MODULEBOX ENTER

BUTTONHDS Pocket Tester:P/N TDS3557011401 • CAN daughterboard - T/N TDS35571228(no longer available for purchase) NOTE: To use the HIM on 2006 and later vehicles,

the CAN daughterboard must be installed.• PC Interface Cable - P/N VET-01002832• AC Power Supply - Model No. TDS606791700• iN Workstation

UPDATING TIPS AND PRECAUTIONS• If you’re updating a control module/unit on a new

vehicle, make sure all its fuses were installed at PDI.• To prevent control unit/module damage, do not

operate anything electrical (audio system, brakes,A/C, power windows, moonroof, etc.) during theupdate.

• Make sure the HDS Tablet, the HDS Pocket Tester,or the iN workstation has the latest version of HDSsoftware. The HDS version number is on the HDSstart-up screen. To find the latest HDS softwareinformation on ISIS, select Search by Vehicle,select Technical Library, expand the ServiceNewsbranch, select Keyword (All Models), enterkeywords HDS VERSION, then select the latestarticle.

01-023 3 of 15

Page 4: -4GB SD Memory Card - P/N OTCH550881 -AC Adapter - P/N … · 2019. 11. 11. · MVCIw as de. using Honda-supplied updating equipment or the iN •Under UPDATING TIPS AND PRECAUTIONS,

11/10/2019 01-023 • Updating Control Units/Modules (Revised 05/15/2009) • 2002 Honda Civic • MotoLogic

https://www.motologic.com/car/0b2cd630-3db7-012c-0340-19005f6e69db/article/03827370-5489-012c-1ea7-001b2106f1f9?returnPath=%2Fcar%2F… 4/15

iN Workstation:NOTE: The screen below is from an iN workstation.The HDS tablet and pocket tester screens are NOTE: The HDS tablet and pocket tester screens aresimilar. similar.

Note: Before reprogramming, please test the vehicle battery and only proceed if the result is good. Ensure the vehicle is connected to abattery booster while reprogramming the control module.

2.016.015.USE.WIN32 DD-MMM-YYYY

HDS VERSION DATABASE UPDATE

• Make sure the Database Update listed in a Honda • If the Database Update listed in the service bulletin isservice communication (service bulletin, product later than that shown by the software, please see theupdate, iN message, etc.) is the same or earlier than the procedures for software installation in thethe ones listed on the Reprogramming screen of the following documents in Tool Information on ISIS (goMVCI (on the MVCI, select CM Update Mode, then to General Publications, then Tool Information):select Reprogramming), or on the Updating Honda - MVCI User Guide (see HDS MVCI FirmwareControl Modules screen on the HDS tablet, the HDS Update section)pocket tester, or the iN workstation.- Honda Diagnostic System (HDS) Tablet SetupMVCI: Instructions- Installation Instructions for HDS ( see PC Software

CM Update Mode for the GNA600, HIM or Pocket Tester ID)• Do not connect an additional power supply to theVer. XXXXXX updating equipment when it is connected to the

vehicle; power is supplied through the DLC.Database Update• To ensure that the control module/unit is notDD-MM-YYYY permanently damaged during updating, verify that

Press ENTER the vehicle’s 12-volt battery is fully charged beforestarting an update.NOTE: If the vehicle’s 12-volt battery drops below 10volts during the update, the programming status barmay go past 100 percent, or the updating tool maydisplay an error message.

• If you have a problem during an update (D4/immobilizer indicator flashes, update tool freezes,etc.), you can minimize the chances of damaging thecontrol unit/module by doing one or more of theseactions:- CRITICAL: Keep the ignition switch in ON (II).- Connect a jumper battery (DO NOT connect a

battery charger).- Disconnect the updating tool from the vehicle’s

DLC.- Reboot the updating tool.- Reconnect the updating tool to the vehicle’s DLC,

and retry the updating procedure.

4 of 15 01-023

Page 5: -4GB SD Memory Card - P/N OTCH550881 -AC Adapter - P/N … · 2019. 11. 11. · MVCIw as de. using Honda-supplied updating equipment or the iN •Under UPDATING TIPS AND PRECAUTIONS,

11/10/2019 01-023 • Updating Control Units/Modules (Revised 05/15/2009) • 2002 Honda Civic • MotoLogic

https://www.motologic.com/car/0b2cd630-3db7-012c-0340-19005f6e69db/article/03827370-5489-012c-1ea7-001b2106f1f9?returnPath=%2Fcar%2F… 5/15

5. The CM Update software information appears.UPDATING WITH THE MVCIPress ENTER to continue.Make sure you have the latest control module (CM)NOTE: If the Database Update is an earlier versionUpdate software loaded from your HDS PC to yourthan the one listed in a Honda serviceMVCI. For loading instructions and other details, refercommunication (service bulletin, product update, iNto the MVCI User Guide on ISIS. The Database Updatemessage, etc.), press ESC, then update your MVCIversion appears when you select Reprogramming,before continuing.then press ENTER.

1. Connect the DLC cable to the MVCI and to thevehicle’s DLC. CM Update Mode

2. Turn the ignition switch to ON (II). The MVCIVer. XXXXXautomatically boots up.

Database UpdateHost Status DD-MM-YYYY

Press ENTERWaiting forHost Connection...

6. Wait for the MVCI to check the vehicle forPress Enter to Config... reprogrammable systems. This may take up to 90

seconds.

CM Update Mode3. Press the ENTER button on the MVCI to see theUser Config menu. Select CM Update Mode.

Checking theReprogrammableUser ConfigVehicle systemDLC Voltage

MVCI SetupUser CustomizeCM Update Mode 7. If there are multiple reprogrammable systems that

need to be updated, select the applicable system.Press ENTER to continue, or press ESC to exit.

4. Select Reprogramming, then press ENTER.System SelectionNOTE: Use these MVCI default settings:

PGM-FISetting 1-Destination: USA

AT (CVT)Language: American English

IMA MotorSetting 2 -Auto Detect: Yes

IMA BatteryContinuous Mode: NoFor more information on these settings, refer to theMVCI User Guide.

CM Update ModeReprogrammingDisplay ErrorSetting 1Setting 2

01-023 5 of 15

Page 6: -4GB SD Memory Card - P/N OTCH550881 -AC Adapter - P/N … · 2019. 11. 11. · MVCIw as de. using Honda-supplied updating equipment or the iN •Under UPDATING TIPS AND PRECAUTIONS,

11/10/2019 01-023 • Updating Control Units/Modules (Revised 05/15/2009) • 2002 Honda Civic • MotoLogic

https://www.motologic.com/car/0b2cd630-3db7-012c-0340-19005f6e69db/article/03827370-5489-012c-1ea7-001b2106f1f9?returnPath=%2Fcar%2F… 6/15

11. Wait for the MVCI to update the control unit/8. The current program ID, the recommended update,module.and other details appear. Press ENTER to

continue, or press ESC to exit.

CM Update ModeCM Update Mode Programming...Current Program ID Do not turn off theXXXXXXXXX ignition switchRecommendedUpdateSystem

12. After the MVCI finishes updating the control unit/XXXXXXXXX module, turn the ignition switch to LOCK (0) whenProgram ID directed by the MVCI.

XXXXX-XXX-XXXX 13. Turn the ignition switch back to ON (II) within 60Model seconds to complete the updating procedure.

NOTE: The MVCI has a countdown timer. If you doXXXXXXXXX not turn the ignition switch to ON (II) within 60Update Description seconds, the MVCI sets an error code.

XXXXXXXXX CM Update ModeTurn the ignitionSwitch to ON within 609. Wait for the MVCI to copy the data for updating the

vehicle. seconds.45 secs to goCM Update Mode

Copying...

10. After the MVCI has copied the files, a confirmationscreen appears. Press ENTER to update thecontrol unit/module, or press ESC to exit.

CM Update ModePress the “Enter”Button to begin theControl moduleProgram update

6 of 15 01-023

Page 7: -4GB SD Memory Card - P/N OTCH550881 -AC Adapter - P/N … · 2019. 11. 11. · MVCIw as de. using Honda-supplied updating equipment or the iN •Under UPDATING TIPS AND PRECAUTIONS,

11/10/2019 01-023 • Updating Control Units/Modules (Revised 05/15/2009) • 2002 Honda Civic • MotoLogic

https://www.motologic.com/car/0b2cd630-3db7-012c-0340-19005f6e69db/article/03827370-5489-012c-1ea7-001b2106f1f9?returnPath=%2Fcar%2F… 7/15

UPDATING WITH THE GNA60014. After finishing the updating procedure, the MVCIgives you the option of updating the same system NOTE: For more information on the GNA600, refer toon another vehicle. For more information on the GNA600 User’s Guide. This guide is on ISIS, underupdating several vehicles, see the MVCI User the Tool Information heading.Guide.

Two modes of updating can be used with the GNA600:Pass-Thru mode and Storage mode. Use Pass-Thru

CM Update Mode mode when the GNA600 can be connected to an iNworkstation and the vehicle at the same time. Use

The Control Module Storage mode when the GNA600 cannot be connectedto the iN workstation and the vehicle at the same time.Update is complete.

Do you want to GNA600 Updating in Pass-Thru Mode1. If not already done, load the latest HDS PCrepeat this system software onto your iN workstation. For loading

update on another instructions, refer to the Tool Informationpublication Installation Instructions for HDS PCvehicle? Software on ISIS.

If YES, Press ENTER NOTE: If the latest software is not loaded and youdo a control unit/module update, the software mayindicate the vehicle has the latest update when it

If NO, Press ESC doesn’t. Updates not done with the latestsoftware are not covered under warranty.

After update is 2. From the iN workstation desktop, select CMcomplete, Update (ECU Rewrite).

check/diagnose any 3. Connect the USB PC interface cable to the iNworkstation and to the GNA600. Click on the ToolsDTCs in each button on the right side of the screen, and make

applicable system. sure the interface device is set to GNA600.4. Return to the Updating Honda Control ModulesUse the Check All. main screen, and click on Pass-thru-Mode.

DTC function.Updating Honda Control Modules

Note: Before reprogramming, please test the vehicle battery and only proceed if the result is good. Ensure the vehicle isconnected to a battery booster while reprogramming the control module.

15. If an error occurs during the updating procedure, an Please select “Pass thru Mode” to update vehicle Control Please select “Storage Mode” to update vehicle ControlModule using the Interface Device connected to the host Module using the Interface Device disconnected from the

error message appears. Keep the ignition switch in PC. host PC.

ON (II). Press ENTER to display the error code.Refer to the CM Update Error Code Table in theMVCI User Guide for more information about thecode and its solutions.

Application Version V6.17.01

Caution Database Update 16-MAR-2009

AN ERROR HASOCCURRED! 5. Connect the DLC cable to the GNA600 and to theKEEP IGNITION ON TO vehicle’s DLC.

PREVENT CONTROLMODULE DAMAGE

Press ENTER.

01-023 7 of 15

Page 8: -4GB SD Memory Card - P/N OTCH550881 -AC Adapter - P/N … · 2019. 11. 11. · MVCIw as de. using Honda-supplied updating equipment or the iN •Under UPDATING TIPS AND PRECAUTIONS,

11/10/2019 01-023 • Updating Control Units/Modules (Revised 05/15/2009) • 2002 Honda Civic • MotoLogic

https://www.motologic.com/car/0b2cd630-3db7-012c-0340-19005f6e69db/article/03827370-5489-012c-1ea7-001b2106f1f9?returnPath=%2Fcar%2F… 8/15

8. Confirm the control module update by Program ID6. Turn the ignition switch to ON (II), and wait until theand Program Part No. Make sure this correspondsgreen No. 2 LED on the GNA600 stays on. Click onwith any information provided in the service bulletinthe check mark to continue.for the update you are doing. Click on Yes tocontinue. Within a few seconds, the CM Updatesoftware loads the program file onto the GNA600.

1. At the vehicle, turn the ignition switch ON (II), the connect the Interface Device to the OBDIIDLC. Please wait for about 30 seconds for the Interface Device to power up and becomeready for use. Then the Green and Yellow LEDs will start to flash alternately. Confirm the Control Module Update

2. Wait until the Green LED glows steadily.

3. Press the “Enter” button on the screen and follow the on-screen instructions. Update SelectedCurrent Program

Program ID: NA3269Program ID: NAA600

Control Module Part No.: 37828-RNA-325Control Module Part No.: 37829-RNA-A61

Program Part No.: 37885-RNA-325Program Part No.: 37805-RNA-A61NOTE: If the interface device LEDs do not match the images above, there is a possibility that an error or mode from aprevious session has not be cleared.

Is this the Update that you want?In order to re-initialize the interface device, disconnect it from the OBDII DLC and the designated power supply beforebeginning the above steps.

Each updatable vehicle system is checked to makesure it is current. Any systems needing an updateare listed on the screen. Highlight the system youwant to update, then click on the check mark to 9. Click on the check mark to begin the control unit/continue. module update.NOTE: Update the systems one at a time. NOTE: To avoid control unit/module damage, do

not interrupt the update.10. Within 60 seconds of update completion, turn the

ignition switch to LOCK (0) and then back to ON(II).These systems on this vehicle have an update available. Update each system separately.

11. Once the software verifies that the control unit/PGM-FI

module has been successfully updated, click onA/T (CVT)

Yes to update another identical vehicle, or click onNo to exit the update program.

Updating Honda Control Modules

The Control Module update is complete.

Do you want to repeat this system update on another vehicle?

7. Verify that the Program ID and the Program PartNo. are for the vehicle you are updating, then clickon the check mark.

After update is complete, check/diagnose any DTCs in each applicable system. Use the Check All DTCs function.Update Information

Current Program ID

NAA610

Recommended Update

System PGM-FI

Program ID NA3250

Program Part No. 37886-RNA-325

Control Module Part No. 37826-RNA-325

Model Civic

Update Description AC out on accel update

8 of 15 01-023

Page 9: -4GB SD Memory Card - P/N OTCH550881 -AC Adapter - P/N … · 2019. 11. 11. · MVCIw as de. using Honda-supplied updating equipment or the iN •Under UPDATING TIPS AND PRECAUTIONS,

11/10/2019 01-023 • Updating Control Units/Modules (Revised 05/15/2009) • 2002 Honda Civic • MotoLogic

https://www.motologic.com/car/0b2cd630-3db7-012c-0340-19005f6e69db/article/03827370-5489-012c-1ea7-001b2106f1f9?returnPath=%2Fcar%2F… 9/15

NOTE: Update the systems one at a time.GNA600 Updating in Storage Mode1. If not already done, load the latest HDS PC

software onto your iN workstation. For loading System Selection

instructions, refer to the ISIS publication InstallationInstructions for HDS PC Software. These systems on this vehicle have an update available. Update each system separately.

NOTE: If the latest software is not loaded and youPGM-FIdo a control unit/module update, the software may A/T (CVT)

indicate the vehicle has the latest update when itdoesn’t. Updates not done with the latestsoftware are not covered under warranty.

2. From the iN workstation desktop, select CMUpdate (ECU Rewrite).

3. Click on the Tools button on the right side of thescreen, and make sure the interface device is set toGNA600.

4. Return to the Updating Honda Control Modules 8. Verify that the Program ID and the Program Partmain screen, then click on Storage Mode and No. are correct, then click on the check mark.follow the on-screen instructions.

5. Take the GNA600 to the vehicle. Connect the DLC Update Information

cable to the GNA600 and to the vehicle’s DLC. Current Program ID

NAA610

6. Turn the ignition switch to ON (II), and wait until the Recommended Update

green No. 2 LED on the GNA600 stays on. Turn the System PGM-FI

ignition switch to LOCK (0), and disconnect the Program ID NA3250

DLC cable from the vehicle. 37886-RNA-325Program Part No.

Control Module Part No. 37826-RNA-325

CivicModel#2 LED (GREEN) Update Description AC out on accel update

7. Connect the USB PC interface cable to the iNworkstation and to the GNA600. Connect the power 9. Confirm the control module update by Program IDsupply unit and power supply cord to the GNA600. and Program Part No. Make sure this correspondsThe GNA600 does a self-check and, after about 30 with any information provided in the service bulletinseconds, its yellow No. 1 and green No. 2 LEDs for the update you are doing. Click on Yes toflash. continue. Within a few seconds, the CM Update

software loads the program file onto the GNA600.

Confirm the Control Module Update

Current Program Update Selected

Program ID: NAAII Program ID: NA3291

Control Module Part No.: 37820-RNA-A61 Control Module Part No.: 37820-RNA-325

Each updatable vehicle system is checked to make Program Part No.: 37815-RNA-A61 Program Part No.: 37825-RNA-325

sure it is current. Any systems needing an update Is this the Update that you want?

are listed on the screen. Highlight the system youwant to update, then click on the check mark tocontinue.

01-023 9 of 15

Page 10: -4GB SD Memory Card - P/N OTCH550881 -AC Adapter - P/N … · 2019. 11. 11. · MVCIw as de. using Honda-supplied updating equipment or the iN •Under UPDATING TIPS AND PRECAUTIONS,

11/10/2019 01-023 • Updating Control Units/Modules (Revised 05/15/2009) • 2002 Honda Civic • MotoLogic

https://www.motologic.com/car/0b2cd630-3db7-012c-0340-19005f6e69db/article/03827370-5489-012c-1ea7-001b2106f1f9?returnPath=%2Fcar%2… 10/15

UPDATING WITH THE HDS TABLET AND THE HDS10. Disconnect the GNA600 from the USB PC interfacePOCKET TESTERcable, then connect the trigger switch adapter block

(yellow) and the trigger switch to the GNA600 as NOTE: This procedure explains how to update with theshown below. (The DLC cable should still be HDS tablet. Updating with the HDS pocket tester isconnected to the GNA600.) similar, but the user interface is modified to fit its

smaller screen.1. If not already done, load the latest HDS PC

software onto your HDS tablet or HDS pockettester. Refer to the instructions included with theHDS Installation Disc.NOTE: If the latest software is not loaded and youdo a control unit/module update, the software mayindicate the vehicle has the latest update when itdoesn’t. Updates not done with the latestsoftware are not covered under warranty.

2. On the HDS Switchboard screen, click on the CMupdate icon.

TRIGGERSWITCH BUTTON

11. Reconnect the DLC cable to the vehicle’s DLC.

12. Turn the ignition switch to ON (II), and wait until thegreen No. 2 LED on the GNA600 stays on. Pressand release the trigger switch button.

13. The yellow No. 1 LED blinks, and the green No. 2LED stays on. This indicates that the control unit/module is being updated.NOTE: To avoid control unit/module damage, do CM UPDATE ICONnot interrupt the update.

3. Turn the ignition switch to ON (II), and connect theDLC cable to the vehicle’s DLC. In the UpdatingHonda Control Modules screen, click on thecheck mark.

Updating Honda Control Modules

14. When the No. 1 LED stays on and the No. 2 LEDgoes off, turn the ignition switch to LOCK (0). Note: Before reprogramming, please test the vehicle battery and only proceed if the result is

good. Ensure the vehicle is connected to a battery booster while reprogramming the controlmodule.

Turn the ignition switch ON (II), then connect HDS Table to the vehicle’s DLC.

15. Turn the ignition switch to ON (II). When the No. 1and No. 2 LEDs stay on, the control unit/module isupdated. Application Version V6.15.04

Database Update 18-DEC-2008

16. Turn the ignition switch to LOCK (0), and Each updatable vehicle system is checked to makedisconnect the DLC cable from the vehicle. To do sure it is current. Any systems needing an updatethe same update on an identical vehicle, repeat are listed on the screen. Highlight the system yousteps 11 thru 16. want to update, then click on the check mark to

continue.

10 of 15 01-023

Page 11: -4GB SD Memory Card - P/N OTCH550881 -AC Adapter - P/N … · 2019. 11. 11. · MVCIw as de. using Honda-supplied updating equipment or the iN •Under UPDATING TIPS AND PRECAUTIONS,

11/10/2019 01-023 • Updating Control Units/Modules (Revised 05/15/2009) • 2002 Honda Civic • MotoLogic

https://www.motologic.com/car/0b2cd630-3db7-012c-0340-19005f6e69db/article/03827370-5489-012c-1ea7-001b2106f1f9?returnPath=%2Fcar%2… 11/15

6. In the HDS Tablet Programming screen, click onNOTE: Update the systems one at a time.the check mark after programming is completed.

System Selection

Programming

These systems on this vehicle have an update available. Update each system separately.Update is being programmed on the HDS Tablet.

PGM-FIA/T (CVT) Programming the HDS Tablet is complete.

Go on to the control module reprogramming procedures.

4. Verify that the Program ID and the Program Part7. In the Updating Honda Control Modules screen,No. are correct, then click on the check mark.

click on the check mark.Update Information

Updating Honda Control ModuleCurrent Program ID

ZAA110

Recommended Update

Program ID ZA4080

Program Part No. 37805-PZA-408

control Module Part No. 37820-PZA-408

TO AVOID PERMANENT CONTROL MODULE DAMAGE, DO NOT TURN OFFYear 2004THE VEHICLE IGNITION SWITCHModel Civic

Engine LDA1

Trans MT

update Description P0420 update

0%

5. Confirm the control module update by Program IDNOTE: To avoid permanent control moduleand Program Part No. Make sure this correspondsdamage, do not turn the ignition switch to LOCK (0)with any information provided in the service bulletinduring the update.for the update you are doing. Click on Yes to

continue. Within a few seconds, the CM Update 8. When updating is complete, follow the screensoftware loads the program file onto the HDS prompts to turn the ignition switch to LOCK (0), andtablet. then to ON (II). To update another system, return tothe Updating Honda Control Modules screen byclicking on the exit button on the right side of theConfirm the Control Module Update

screen.Current Program Update Selected

Program ID: ZAA110 Program ID: ZA4080

Control Module Part No.: 37820-PZA-A11 Control Module Part No.: 37820-PZA-408

Program Part No.: 37805-PZA-A11 Program Part No.: 37805-PZA-408

EXIT BUTTONIs this the Update that you want?

01-023 11 of 15

Page 12: -4GB SD Memory Card - P/N OTCH550881 -AC Adapter - P/N … · 2019. 11. 11. · MVCIw as de. using Honda-supplied updating equipment or the iN •Under UPDATING TIPS AND PRECAUTIONS,

11/10/2019 01-023 • Updating Control Units/Modules (Revised 05/15/2009) • 2002 Honda Civic • MotoLogic

https://www.motologic.com/car/0b2cd630-3db7-012c-0340-19005f6e69db/article/03827370-5489-012c-1ea7-001b2106f1f9?returnPath=%2Fcar%2… 12/15

6. Turn the ignition switch to ON (II), and wait until theUPDATING WITH THE HIMgreen No. 1 LED on the HIM stays on. Click on theTwo updating modes can be used with the HIM: Pass-check mark to continue.Thru mode and Storage mode. Pass-Thru mode is

used when the HIM can be connected to an iNworkstation and the vehicle at the same time. Storage Updating Honda Control Modules

mode is used when the HIM cannot be connected tothe iN workstation and the vehicle at the same time. 1. At the vehicle, turn the ignition switch ON (II), then connect the Interface Device in the OBDII

DLC. The Green and Yellow LEDs flash alternately.

2. Wait until the Green LED glows steadily.HIM Updating in Pass-Thru ModeNOTE: If the red No. 3 LED on the HIM comes on or 3. Press the “Enter” button on the screen and follow the on-screen instruction.

flashes during the update, go to Diagnosing HIM ErrorCodes.1. If not already done, load the latest HDS PC

software onto your iN workstation. For loadingApplication Version V6.17.01

instructions, refer to the Tool Information Database Update 16-MAR-2009

publication Installation Instructions for HDS PCSoftware on ISIS.NOTE: If the latest software is not loaded and youdo a control unit/module update, the software may Each updatable vehicle system is checked to makeindicate the vehicle has the latest update when it sure it is current. Any systems needing an updatedoesn’t. Updates not done with the latest are listed on the screen. Highlight the system yousoftware are not covered under warranty. want to update, then click on the check mark to

continue.2. From the iN workstation desktop, select CMNOTE: Update the systems one at a time.Update (ECU Rewrite).

3. Connect the PC interface cable to the iNSystem Selectionworkstation and to the HIM.

4. Return to the Updating Honda Control Modules These systems on this vehicle have an update available. Update each system separately.

main screen, and click on Pass-thru-Mode.PGM-FIA/T (CVT)

Note: Before reprogramming, please test the vehicle battery and only proceed if the result is good. Ensure the vehicle is connected to abattery booster while reprogramming the control module.

7. Verify that the Program ID and the Program PartApplication Version V6.13.09

No. are for the vehicle you are updating, then clickDatabase Update 01-SEP-2008

on the check mark.

Update Information

5. Connect the HIM to the vehicle’s DLC. Current Program ID

NAA610

Recommended Update

System PGM-FI

Program ID NA3250

Program Part No. 37886-RNA-325

Control Module Part No. 37826-RNA-325

Model Civic

Update Description AC out on accel update

12 of 15 01-023

Page 13: -4GB SD Memory Card - P/N OTCH550881 -AC Adapter - P/N … · 2019. 11. 11. · MVCIw as de. using Honda-supplied updating equipment or the iN •Under UPDATING TIPS AND PRECAUTIONS,

11/10/2019 01-023 • Updating Control Units/Modules (Revised 05/15/2009) • 2002 Honda Civic • MotoLogic

https://www.motologic.com/car/0b2cd630-3db7-012c-0340-19005f6e69db/article/03827370-5489-012c-1ea7-001b2106f1f9?returnPath=%2Fcar%2… 13/15

11. Once the software verifies that the control unit/8. Confirm the control module update by Program IDmodule has been successfully updated, click onand Program Part No. Make sure this correspondsYes to update another identical vehicle, or click onwith any information provided in the service bulletinNo to exit the update program.for the update you are doing. Click on Yes to

continue. Within a few seconds, the CM Updatesoftware loads the program file onto the HIM. Updating Honda Control Modules

Confirm the Control Module Update

The Control Module update is complete.Update SelectedCurrent Program

NA3269Program ID:NAA600Program ID:

37828-RNA-325Control Module Part No.:37829-RNA-A61Control Module Part No.:

Do you want to repeat this system update on another vehicle?37885-RNA-325Program Part No.:37805-RNA-A61Program Part No.:

Is this the Update that you want?

After update is complete, check/diagnose any DTCs in each applicable system. Use the Check All DTCs function.

HIM Updating in Storage ModeNOTE: If the red No. 3 on the HIM comes on or flashes9. Click on the check mark to begin the control unit/ during the update, go to Diagnosing HIM Error Codes.module update.1. If not already done, load the latest HDS PCNOTE: To avoid control unit/module damage, do software onto your iN workstation. For loadingnot interrupt the update. instructions, refer to the Tool Information

publication Installation Instructions for HDS PCSoftware on ISIS.Programming

NOTE: If the latest software is not loaded and youUpdate is being programmed on the Interface Device.

do a control unit/module update, the software mayindicate the vehicle has the latest update when itProgramming the Interface Device is complete.

doesn’t. Updates not done with the latestPress the Enter button on the screen to continue the conrol module reprogramming procedures.

software are not covered under warranty.2. From the iN workstation desktop, select CM

Update (ECU Rewrite).3. Click on the tools button on the right side of the

screen, and make sure the interface device is set toHIM.

10. Within 60 seconds of update completion, turn theignition switch to LOCK (0) and then back to ON TOOLS BUTTON(II).

4. Return to the Updating Honda Control Modulesmain screen, then select Storage Mode and followthe on-screen instructions.

5. Take the HIM to the vehicle, and connect it to thevehicle’s DLC.

6. Turn the ignition switch to ON (II), and wait until thegreen No. 1 LED on the HIM stays on. Turn theignition switch to LOCK (0), and disconnect the HIMfrom the vehicle.

01-023 13 of 15

Page 14: -4GB SD Memory Card - P/N OTCH550881 -AC Adapter - P/N … · 2019. 11. 11. · MVCIw as de. using Honda-supplied updating equipment or the iN •Under UPDATING TIPS AND PRECAUTIONS,

11/10/2019 01-023 • Updating Control Units/Modules (Revised 05/15/2009) • 2002 Honda Civic • MotoLogic

https://www.motologic.com/car/0b2cd630-3db7-012c-0340-19005f6e69db/article/03827370-5489-012c-1ea7-001b2106f1f9?returnPath=%2Fcar%2… 14/15

9. Confirm the control module update by Program ID7. Connect the PC interface cable to the iNand Program Part No. Make sure this correspondsworkstation and to the HIM. Connect the powerwith any information provided in the service bulletinsupply unit and power supply cord to the HIM. Afterfor the update you are doing. Click on Yes toseveral seconds, the green and yellow LEDs flash.continue. Within a few seconds, the CM UpdateEach updatable vehicle system is checked to makesoftware loads the program file onto the HIM.sure it is current. Any systems needing an update

are listed on the screen. Highlight the system youwant to update, then click on the check mark to Confirm the Control Module Update

continue.Current Program Update Selected

NOTE: Update the systems one at a time. Program ID: NAAII Program ID: NA3291

Control Module Part No.: 37820-RNA-A61 Control Module Part No.: 37820-RNA-325

Program Part No.: 37815-RNA-A61 Program Part No.: 37825-RNA-325

System Selection Is this the Update that you want?

These systems on this vehicle have an update available. Update each system separately.

PGM-FIA/T (CVT)

10. Disconnect the HIM from the PC interface cable.11. Reconnect the HIM to the vehicle’s DLC.

12. Turn the ignition switch to ON (II), and wait until thegreen No. 1 LED on the HIM stays on. Press and8. Verify that the Program ID and the Program Part release the ENTER button on the HIM.No. are correct, then click on the check mark.

13. The green No. 1 LED stays on, and the yellow No.2 LED blinks. This indicates that the control unit/Update Information

module is being updated.Current Program ID

NOTE: To avoid control unit/module damage, doNAA610

not interrupt the update.Recommended Update

System PGM-FI

14. When the yellow No. 2 LED stays on, turn theProgram ID NA3250

Program Part No. 37886-RNA-325

ignition switch to LOCK (0).Control Module Part No. 37826-RNA-325

Model Civic

15. Turn the ignition switch to ON (II). When the greenUpdate Description AC out on accel update

No. 1 and the yellow No. 2 LEDs stay on, thecontrol unit/module is updated.

16. Turn the ignition switch to LOCK (0), anddisconnect the HIM from the vehicle. To do thesame update on an identical vehicle, repeat steps11 thru 16.

14 of 15 01-023

Page 15: -4GB SD Memory Card - P/N OTCH550881 -AC Adapter - P/N … · 2019. 11. 11. · MVCIw as de. using Honda-supplied updating equipment or the iN •Under UPDATING TIPS AND PRECAUTIONS,

11/10/2019 01-023 • Updating Control Units/Modules (Revised 05/15/2009) • 2002 Honda Civic • MotoLogic

https://www.motologic.com/car/0b2cd630-3db7-012c-0340-19005f6e69db/article/03827370-5489-012c-1ea7-001b2106f1f9?returnPath=%2Fcar%2… 15/15

HIM Self-TestDiagnosing HIM Error CodesIf you suspect there’s a problem with the HIM, reviewIf the red No. 3 LED on the HIM came on or wasthe instructions in this service bulletin to make sure youflashing during the update, do this:are using it correctly. If you still think there’s a problem,1. Leave the ignition switch in ON (II) while you do this self-test:disconnect the HIM from the vehicle’s DLC.1. If not already done, load the latest HDS software2. If not already done, load the latest HDS software

onto the iN workstation.onto the iN workstation.3. Connect the HIM to the iN workstation. Connect the 2. Restart the CM Update application on the iN

small end of the PC interface cable to the PC port workstation.on the HIM.

3. On the right side of the screen, click on the tools4. If not already done, connect the PC end of the blue button.PC interface cable to the 9P serial port on the iNworkstation.

5. Connect the 110 VAC/12 VDC power supply to theHIM and to a wall outlet.

TOOLS BUTTON6. Restart the CM Update application on the iNworkstation.

4. Click on HIM Self-Test Procedure.7. On the right side of the screen, click on the viewerror button. 5. Follow the on-screen instructions to run the HIM

self-test.6. If the self-test indicates a problem with the HIM, call

the Special Tools hotline at 800-346-6327 for repairinstructions.VIEW ERROR BUTTON

8. Click on View Error at the bottom of the screen todisplay the problem encountered while the HIMwas connected to the vehicle.• If you get a Code 40 error message (usually

caused by a communication error between theHIM and the workstation), do this:- Do the HIM self-test procedure (see HIM Self-

Test).- Move the blue PC interface cable to another

communication port on the back of thecomputer.

- If one of the communication ports on the backof the computer has another cable connectedto it, disconnect that cable, leave itdisconnected during the HIM procedure, andconnect the blue PC interface cable to thatport.

- Connect the HIM to another computer. (SomeiN workstations require an internalcommunication port setup procedure. For help,call the iN Support Center at 800-245-4343.)

• If you get a Code 50 error message (usuallycaused by a communications error between theHIM and the vehicle’s DLC), do this:- Diagnose and clear any DTCs. (The control

unit/module must be free of DTCs before youcan update it.)

- Make sure there’s a good connection betweenthe HIM and the DLC.

- Retry the update using the procedures in thisservice bulletin or on the back of the HIM.

- If needed, call Tech Line for further help.

01-023 15 of 15