43.35” (LENGTH OF INNER LIQUID HE RESERVIOR)

CONNECTION CHAMBER: FF 4.75” FF: FLANGE-TO-FLANGE DISTANCE

10.45” TO 12.45”

6.35” TO 8.35” (JACK -2” TO 0) (BOTTOM OF HE COLD FINGER TO A-A FOCAL POINT)

COARSE-Z JACK + RNN FF 5.7” TO 7.7”

NIPPLE 3.56”

2.47”

50.4” (BETWEEN BOTTOM OF CAGE AND MIDDLE OF CONNECTION CHAMBER) = 42.55” + (7.85” BASED ON SCANNING POSITION AT JACK @ -0.5”)

PROBE/SCANNER HEIGHT 1.42”

(36MM SPECIFIED BY

INTEMATIX) BOTTOM PLATE THICKNESS

0.25”

~ 3.33” TO 5.33”

SCANNING POSITION: Z-STAGE (ATTOCUBE – FULL RANGE

15MM) EXTENSION ~ 0.43” (11MM) JACK AT -0.5” (THIS DIMENSION

DETERMINES HEIGHT OF SPM CAGE – POSSIBLE RANGE -0.2” TO -0.8”)

TRANSFER POSITION: Z-STAGE ~ 0 => JACK NEEDS TO GO DOWN ~1” (@ -1.5”)

10-PIN FEEDTHROUGH FOR SIGNALS (2 FOR TUNNELING CURRENT)HV CABLES (PZT) GO UP THROUGH THE CONNECTION CHAMBER

3.86”

LIQUID N2 CRYO-SHIELD/ANCHOR

COARSE-Z JACK: FF 4.27” TO 6.27” (-2” TO 0)

RNN: DIFFERENTIALLY PUMPED ROTARY PLATFORM – POLAR ROTATION

~ 7.33 TO 8.19”

0.84”

FEMALE SMA CONNECTOR

LENGTH OF RF CABLE:53.9” (FROM BOTTOM OF PROBE CAGE TO FACE OF MALE SMA CONNECTOR) 50.4” + ~0.5” (BENT SECTION IN MIDDLE OF CONNECTION CHAMBER) + 3” (STRAIGHT SECTION BEYOND BENT TO FACE OF MALE CONNECTOR)

A U-SHAPED SECTION NEEDS TO BE ADDED TO EACH OF THE RF CABLES BELOW THE CAGE TO CONNECT TO THE PROBETHE “U’ SECTIONS NEED TO FIT WITHIN A CYLINDER OF HEIGHT 2” BY ID 2.37”

LENGTH OF RF CABLE:53.9” (FROM BOTTOM OF PROBE CAGE TO FACE OF MALE SMA CONNECTOR) 50.4” + ~0.5” (BENT SECTION IN MIDDLE OF CONNECTION CHAMBER) + 3” (STRAIGHT SECTION BEYOND BENT TO FACE OF MALE CONNECTOR)

A U-SHAPED SECTION NEEDS TO BE ADDED TO EACH OF THE RF CABLES BELOW THE CAGE TO CONNECT TO THE PROBETHE “U’ SECTIONS NEED TO FIT WITHIN A CYLINDER OF HEIGHT 2” BY ID 2.37”

FEMALE SMA CONNECTOR

RF CABLE

2.47”

43.35” (LENGTH OF INNER LIQUID HE RESERVIOR)

CONNECTION CHAMBER: FF 4.75” FF: FLANGE-TO-FLANGE DISTANCE

10.45” TO 12.45”

6.35” TO 8.35” (JACK -2” TO 0) (BOTTOM OF HE COLD FINGER TO A-A FOCAL POINT)

COARSE-Z JACK + RNN FF 5.7” TO 7.7”

NIPPLE 3.56”

2.47”

PROBE/SCANNER HEIGHT 1.42”

(36MM SPECIFIED BY

INTEMATIX) BOTTOM PLATE THICKNESS

0.4”

~ 3.33” TO 5.33”

SCANNING POSITION: Z-STAGE (ATTOCUBE – FULL RANGE

15MM) EXTENSION ~ 0.39” (10MM) JACK AT -0.5” (THIS DIMENSION

DETERMINES HEIGHT OF SPM CAGE – POSSIBLE RANGE -0.2” TO -0.8”)

TRANSFER POSITION: Z-STAGE ~ 0 => JACK NEEDS TO GO DOWN ~1” (@ -1.5”)

10-PIN FEEDTHROUGH FOR SIGNALS (2 FOR TUNNELING CURRENT)HV CABLES (PZT) GO UP THROUGH THE CONNECTION CHAMBER

3.86”

LIQUID N2 CRYO-SHIELD/ANCHOR

COARSE-Z JACK: FF 4.27” TO 6.27” (-2” TO 0)

RNN: DIFFERENTIALLY PUMPED ROTARY PLATFORM – POLAR ROTATION

~ 7.33 TO 8.19”

0.84”

FEMALE SMA CONNECTOR

LENGTH OF RF CABLE:53.9” (FROM BOTTOM OF PROBE CAGE TO FACE OF MALE SMA CONNECTOR) 50.4” + ~0.5” (BENT SECTION IN MIDDLE OF CONNECTION CHAMBER) + 3” (STRAIGHT SECTION BEYOND BENT TO FACE OF MALE CONNECTOR)

A U-SHAPED SECTION NEEDS TO BE ADDED TO EACH OF THE RF CABLES BELOW THE CAGE TO CONNECT TO THE PROBETHE “U’ SECTIONS NEED TO FIT WITHIN A CYLINDER OF HEIGHT 2” BY ID 2.37”

LENGTH OF RF CABLE:53.9” (FROM BOTTOM OF PROBE CAGE TO FACE OF MALE SMA CONNECTOR) 50.4” + ~0.5” (BENT SECTION IN MIDDLE OF CONNECTION CHAMBER) + 3” (STRAIGHT SECTION BEYOND BENT TO FACE OF MALE CONNECTOR)

A U-SHAPED SECTION NEEDS TO BE ADDED TO EACH OF THE RF CABLES BELOW THE CAGE TO CONNECT TO THE PROBETHE “U’ SECTIONS NEED TO FIT WITHIN A CYLINDER OF HEIGHT 2” BY ID 2.37”

FEMALE SMA CONNECTOR

RF CABLE

Updated version 8/23/07

9.67” =(50.55”+2.47”-43.35”)

50.55” (BASED ON SCANNING POSITION AT JACK @ -0.5”)

5.6

5”

39.25”

~ 17” TO THE TABLE