380-137a/bx25d installation manual · 2017-11-13 · b2650 and b3350 3rd function valve...
TRANSCRIPT
![Page 1: 380-137A/BX25D installation Manual · 2017-11-13 · b2650 and b3350 3rd function valve installation manual use part# 380-168a 11/13/2017](https://reader034.vdocuments.us/reader034/viewer/2022043005/5f89fb171c1a7b28f43bd557/html5/thumbnails/1.jpg)
B2650 AND B3350
3 RD FUNCTION VALVE INSTALLATION MANUAL
USE PART# 380-168A
11/13/2017
![Page 2: 380-137A/BX25D installation Manual · 2017-11-13 · b2650 and b3350 3rd function valve installation manual use part# 380-168a 11/13/2017](https://reader034.vdocuments.us/reader034/viewer/2022043005/5f89fb171c1a7b28f43bd557/html5/thumbnails/2.jpg)
On the other side of valve locate Port A & B. Install PN# 851-084C MORB in each port. then Install Male Tips to this fitting.
![Page 3: 380-137A/BX25D installation Manual · 2017-11-13 · b2650 and b3350 3rd function valve installation manual use part# 380-168a 11/13/2017](https://reader034.vdocuments.us/reader034/viewer/2022043005/5f89fb171c1a7b28f43bd557/html5/thumbnails/3.jpg)
Assemble Valve.Locate port P & T and install one PN# 811-170C on each port.
![Page 4: 380-137A/BX25D installation Manual · 2017-11-13 · b2650 and b3350 3rd function valve installation manual use part# 380-168a 11/13/2017](https://reader034.vdocuments.us/reader034/viewer/2022043005/5f89fb171c1a7b28f43bd557/html5/thumbnails/4.jpg)
Install Valve Mount Bracket:
Position valve, male tips up then attach PN# 380-256D (Valve Mount Bracket) to loader support frame with 2 HHCS 3/8-16X1 ½ GR5 bolts and flat washers.Tighten to 31 ft.-lbs.
Install Valve Body (810-926C) to Valve Mount Bracket with 2 HSHCS ¼-20X7/8
![Page 5: 380-137A/BX25D installation Manual · 2017-11-13 · b2650 and b3350 3rd function valve installation manual use part# 380-168a 11/13/2017](https://reader034.vdocuments.us/reader034/viewer/2022043005/5f89fb171c1a7b28f43bd557/html5/thumbnails/5.jpg)
Chock tires and jack up the RH rear of tractor, place a jack stand under axle and remove tire.
Remove the seat and bolts from the seat support bracket (both sides). Then remove these for access to the top of the return tank fitting.
![Page 6: 380-137A/BX25D installation Manual · 2017-11-13 · b2650 and b3350 3rd function valve installation manual use part# 380-168a 11/13/2017](https://reader034.vdocuments.us/reader034/viewer/2022043005/5f89fb171c1a7b28f43bd557/html5/thumbnails/6.jpg)
Locate the steel tube from the Power Beyond and remove line.
![Page 7: 380-137A/BX25D installation Manual · 2017-11-13 · b2650 and b3350 3rd function valve installation manual use part# 380-168a 11/13/2017](https://reader034.vdocuments.us/reader034/viewer/2022043005/5f89fb171c1a7b28f43bd557/html5/thumbnails/7.jpg)
Install 48” Hose (841-563C) from the Power Beyond and routed under the tractor to the “P” port. Secure hose with cable ties.
Install adapter (811-133C) 9/16MJIC ¾ MORB and elbow (811-169C) EL 9/16MJIC 9/16 FJIC
![Page 8: 380-137A/BX25D installation Manual · 2017-11-13 · b2650 and b3350 3rd function valve installation manual use part# 380-168a 11/13/2017](https://reader034.vdocuments.us/reader034/viewer/2022043005/5f89fb171c1a7b28f43bd557/html5/thumbnails/8.jpg)
Install with Elbow (851-768C) EL 3/8MBSPP 9/16MJIC.
May require the removal of the Seat Support Stud.
Attach the 62” hose (811-253C) from the “T” port of valve to this location. Secure hoses with cable ties.
Re-attach seat support stud then install the seat support and the seat.
![Page 9: 380-137A/BX25D installation Manual · 2017-11-13 · b2650 and b3350 3rd function valve installation manual use part# 380-168a 11/13/2017](https://reader034.vdocuments.us/reader034/viewer/2022043005/5f89fb171c1a7b28f43bd557/html5/thumbnails/9.jpg)
Install Bulkhead bracket (380-257D) to torque tube of loader with removed hardware.
Install 2 of 851-344C (bulkhead fitting) one in each hole of bracket, as shown. Jam nuts are used to hold them secure to the bracket.
Attach 2 male tips (811-394C) to front side.
![Page 10: 380-137A/BX25D installation Manual · 2017-11-13 · b2650 and b3350 3rd function valve installation manual use part# 380-168a 11/13/2017](https://reader034.vdocuments.us/reader034/viewer/2022043005/5f89fb171c1a7b28f43bd557/html5/thumbnails/10.jpg)
Attach 2 (811-040C) 45 deg. Elbows to the bulkhead adapters.
Attach 2 (851-376C) 86” shielded hoses to JIC side. Run other end of hoses to valve.
![Page 11: 380-137A/BX25D installation Manual · 2017-11-13 · b2650 and b3350 3rd function valve installation manual use part# 380-168a 11/13/2017](https://reader034.vdocuments.us/reader034/viewer/2022043005/5f89fb171c1a7b28f43bd557/html5/thumbnails/11.jpg)
Route hoses along loader arm and through loader loop bracket. Secure where needed with cable ties.
Install 2 female tips (811-870C) on hoses and connect to valve.
![Page 12: 380-137A/BX25D installation Manual · 2017-11-13 · b2650 and b3350 3rd function valve installation manual use part# 380-168a 11/13/2017](https://reader034.vdocuments.us/reader034/viewer/2022043005/5f89fb171c1a7b28f43bd557/html5/thumbnails/12.jpg)
Remove loader knob (pulls off) assemble handle as pictured. Attach handle to stem, make sure wire harness clears set screws. Run wiring down stem (zip tie) to valve wiring harness.
![Page 13: 380-137A/BX25D installation Manual · 2017-11-13 · b2650 and b3350 3rd function valve installation manual use part# 380-168a 11/13/2017](https://reader034.vdocuments.us/reader034/viewer/2022043005/5f89fb171c1a7b28f43bd557/html5/thumbnails/13.jpg)
The two Red (+) wires from the Control Handle will attach to Fuse Holder. Install supplied 10 AMP fuse, attach to Positive (+)battery post.
The two Black wires from Control Handle will need attached to pig tail from the Valve. Connect one Black to Black and one Black to White. (Butt connectors are not supplied). Secure all wiring with cable ties.
Wire Harness from Control handle
To Positive Battery Post
Wire Harness to Valve
Fuse Holder
![Page 14: 380-137A/BX25D installation Manual · 2017-11-13 · b2650 and b3350 3rd function valve installation manual use part# 380-168a 11/13/2017](https://reader034.vdocuments.us/reader034/viewer/2022043005/5f89fb171c1a7b28f43bd557/html5/thumbnails/14.jpg)
Check the following:
Start tractor and check for leaks.
Check tractor hydraulic levels, add as needed.
Check to make sure 3rd function valve energizes and the indicator light on the front correspond to the button being pushed.
If not engaging check the fuse , if it is blown check the wires to make sure the set screws are not pinching the wires.
![Page 15: 380-137A/BX25D installation Manual · 2017-11-13 · b2650 and b3350 3rd function valve installation manual use part# 380-168a 11/13/2017](https://reader034.vdocuments.us/reader034/viewer/2022043005/5f89fb171c1a7b28f43bd557/html5/thumbnails/15.jpg)
11/13/2017