3600 series 3600 series heavy duty pumps...complete packaged pump solutions 1300 allpumps (255 786) ...
TRANSCRIPT
COMPLETE PACKAGED PUMP SOLUTIONS 1300 ALLPUMPS (255 786) www.allpumps.com.au
33GE
AR p
umps
Gear PumPs 3600 SERIES
3600 Series Heavy Duty PumpsGeneral Purpose Pumps for Mixing, Blending, Recirculating, Fixed and Mobile Transfer
Up to 468 GPM • Up to 125 PSIThese pumps operate smoothly and with equal efficiency in either direction of rotation. They effectively handle heavy, viscous materials such as asphalt, molasses, roofing compounds, and printing inks, as well as fuel oils, gasolines, and similar thin liquids.
Pumps can be supplied in several materials of construction, with or without built-in relief valves. Pumps can be assembled either hi-drive or low-drive, and are available with conventional packed box or lapped-face mechanical shaft seal. They can be direct driven or driven through a built-in gear reduction with a wide range of ratios. These pumps operate equally well regardless of the mounting configuration or the direction of rotation.
FeaturesQuiet-Running Helical Gears• Heat treated cast-iron pumping gears are accurately
machined for quiet, efficient operation and long life.
• The pumping gears are keyed to their shafts with a sliding fit and are easily replaced.
• Accurate machining insures proper meshing, and reduces friction and vibration.
Long-Lasting Bearing Surfaces• Bearings are special wear-resistant, high-lead
bronze. Iron and carbon bearings are available.
• Four heavy duty sleeve bearings give positive support to pumping gears and insure long, efficient service.
• Bearing grooves allow circulation of the liquid being pumped for lubrication & control of bearing temperature.
• Outboard drive shaft bearing supports external radial loads and absorbs thrust loads.
Precision-Ground Shafts• The steel shafts are induction hardened in the
bearing and sealing areas and are precision ground to exacting standards for maximum life.
• Hardened stainless steel shafts available.
Rugged Housing• Standard castings are cast iron.
• Precise manufacturing tolerances provide minimum clearances for maximum pumping efficiency.
• Large, hardened steel dowel pins insure positive alignment between the faceplate, case, and backplate.
COMPLETE PACKAGED PUMP SOLUTIONS 1300 ALLPUMPS (255 786) www.allpumps.com.au
34Gear PumPs
3600 SERIES
MODELTHEORETICAL CAPACITY
MAXIMUM SPEEDMAXIMUM FLOw AT MAXIMUM SPEED (0 DISCHARGE PRESSURE)
MAXIMUM PRESSURE
PORT CONNECTION
3611/3711 416.4 CC/REV 750 RPM 18.6 M3/HR 8.6 Bar 2" BSP
4611/4711 416.4 CC/REV 750 RPM 18.6 M3/HR 8.6 Bar 2" BSP
3617/3717 643.5 CC/REV 750 RPM 28.8 M3/HR 8.6 Bar 2" BSP
4617/4717 643.5 CC/REV 750 RPM 28.8 M3/HR 8.6 Bar 3" BSP
3622/3722 832.8 CC/REV 750 RPM 37.2 M3/HR 8.6 Bar 3" BSP
4622/4722 832.8 CC/REV 600 RPM 37.2 M3/HR 8.6 Bar 4" BSP
3632/3732 1211.33 CC/REV 900 RPM 65.4 M3/HR 8.6 Bar 3" BSP
3635/3735 1324.89 CC/REV 600 RPM 50.4 M3/HR 8.6 Bar 3" BSP
3643/3743 1627.73 CC/REV 900 RPM 87.9 M3/HR 8.6 Bar 3" BSP
3648/3748 1817.0 CC/REV 900 RPM 106.2 M3/HR 8.6 Bar 4" BSP
3658/3758 2195.53 CC/REV 600 RPM 82.9 M3/HR 8.6 Bar 4" BSP
4658/4758 2195.53 CC/REV 600 RPM 82.9 M3/HR 8.6 Bar 4" BSP
STANDARD OPTION
Housing Cast Iron
Shafts Steel Stainless Steel
Gears Hardened Iron Stainless Steel
Bearings BronzeCarbonIronGlass/PTFE
Packing Graphite Filament Teflon
Mechanical Seal Carbon/Stainless (Nitrile Elastomers)
Viton ElastomersTeflon Elastomers
Performance
Materials of Construction
N.B.: Not all combinations are available on all pump models.
COMPLETE PACKAGED PUMP SOLUTIONS 1300 ALLPUMPS (255 786) www.allpumps.com.au
35GE
AR p
umps
Gear PumPs 3600 SERIES
Model Number Designation3(i)
6(ii)
17(iii)
HBFRV(iv)
8851(v)
(i) Port Orientation 3 – 3600 Series with right angle ports
(ii) Shaft Sealing 6 – Packing 7 – Mechanical Seal
(iii) Flowrate in US Gallons/100 Revolutions 11 = 0.416 L/Rev (0.11 gpr) 17 = 0.644 L/Rev (0.17 gpr) 22 = 0.833 L/Rev (0.22 gpr) 32 = 1.211 L/Rev (0.32 gpr) 35 = 1.32 L/Rev (0.35 gpr) 43 = 1.63 L/Rev (0.43 gpr) 48 = 1.82 L/Rev (0.48 gpr) 58 = 2.20 L/Rev (0.58 gpr)
(iv) Pump Head Arrangement H – Pump without outboard bearing HB – Pump with outboard bearing F – Pump with flanged connections (bolt on threaded flange) RV – Pump with integral pressure relief valve
(v) Specialty Code 8851 = BSP(F) Connections
COMPLETE PACKAGED PUMP SOLUTIONS 1300 ALLPUMPS (255 786) www.allpumps.com.au
36Gear PumPs
3600 SERIES
Key Components
BEARINGSFour heavy duty sleeve bearings give positive support to pumping gears and ensure long, efficient service. A special wear-resistant, high-lead bronze bearing is standard on 3600 Series Pumps. For thin non-abrasive liquids we offer optional carbon bearings, as well as iron bearings for abrasive liquids. The bearings are grooved to allow circulation of the liquid being pumped for lubrication & control of bearing temperature
GEARSThe helical pumping gears are machined from heat treated cast iron because of its excellent wear resistance.
For chemical pumping applications, the standard gears can be replaced with stainless steel or bronze. An optional Delrin® idler gear can be used for quieter operation when running thin liquids.
SHAFTSStandard steel shafts are induction hardened in the bearing and sealing areas, and are precision ground to exacting standards for maximum life. Hardened stainless steel shafts are also available upon request.
HOUSINGOur rugged cast-iron housings are manufactured to precise tolerances, providing minimum clearances for maximum pumping efficiency. Large, hardened steel dowel pins ensure positive alignment between the faceplate, case, and backplate.
GASKETS3600 Series Pumps come standard with fiber gaskets that are used up to 212oF/100oC. For higher temperature applications (up to 450oF/232oC) we offer other optional gasket materials.
COMPLETE PACKAGED PUMP SOLUTIONS 1300 ALLPUMPS (255 786) www.allpumps.com.au
37GE
AR p
umps
Gear PumPs 3600 SERIES
Relief Valves & JacketingRELIEF VALVEIn the event of overpressure situations, our adjustable relief valve protects personnel and equipment by returning liquids to the suction side of the pump. Various spring sizes can be specified to handle a wide range of operating conditions.
Roper Pump’s inverted poppet relief valve is designed without close fitting guides that can clog and cause excessive pressures when the valve does not open freely. The valve will provide protection in only one direction of rotation. However it can be positioned easily to either side of the pump to accommodate flow direction.
BI-DIRECTIONAL RELIEF VALVE*Roper Pump’s integral bi-directional pressure relief valve offers reliable protection of your personnel and equipment, regardless of which direction you are pumping. You can reverse flow without disabling pressure relief operability, or compromising operator safety. Based on our rugged and time proven standard relief valves, this offers you a lighter weight, lower cost alternative compared to externally plumbed systems.
JACKETING**Whether the fluid to be pumped must be heated, cooled, or maintained at a specific temperature, a jacketed Roper pump will handle difficult-to-pump materials such as Bunker C, molasses, asphalt mixes, refined sugars, creosote, printing ink, and other viscous fluids which require temperature control for satisfactory handling.
Roper Pump jacketed pumps provide efficient heat transfer to the packing, seal relief valve, bearing areas, and endplates of the pump. The jackets are suitable for use with steam, hot or cold water, heat transfer oil, etc., as heating or cooling mediums.
Jacketing is available on the faceplate only, backplate only, or on both.
*Available on 11, 17 and 22 sizes
**Jacketing is not available on 32, 43 and 48 sizes
COMPLETE PACKAGED PUMP SOLUTIONS 1300 ALLPUMPS (255 786) www.allpumps.com.au
38Gear PumPs
3600 SERIES
Pump Seals
MECHANICAL SEALMechanical seals are for those applications where product leakage is unacceptable. Under proper conditions the mechanical seal has a longer service life than the packed box and does not require adjustment. The standard mechanical seal is an elastomeric bellows type seal. A PTFE wedge seal is also available.
PACKED BOXOur standard packing is suited for general purpose applications, and is easily replaced with split ring packing. For optimum performance, the gland should be adjusted to allow slight seepage. Standard packing is graphite, with several optional packing materials available for applications involving high temperatures or mildly corrosive liquids, or those requiring compatibility with food products.
TRIPLE LIP SEALOffering the same high degree of sealing reliability as a mechanical seal, triple lip seals are better suited for viscous products that tend to set up while the pump is idle, such as resins, glues and paints. The lips create an effective barrier to product leakage, and will move freely upon resumption of pumping a thickening substance. In cases where extreme circumstances can cause catastrophic failure of mechanical seals, the resilient nature of the triple lip seal makes it relatively immune to sudden failure.
COMPLETE PACKAGED PUMP SOLUTIONS 1300 ALLPUMPS (255 786) www.allpumps.com.au
39GE
AR p
umps
Gear PumPs 3600 SERIES
H &
HB
B
HG
BH
& H
GH
B
F
F
F
F
G
G
O
O
V
V
P
P
PORT
PORT
KEY
PORT
PORT
PORT
PORT
F
F
F
F H
H
HG
H
O
O
P
P
P
P
PORT
PORT
R
E
E
E
E
R
R
R
E
E
E
E
NU
C
C
C
C
N
U
D
NM
NM
NM
NM
W
W
N
N
X
X
U
U D
D
D
K
K
K
K
Dimensions90° Ports
COMPLETE PACKAGED PUMP SOLUTIONS 1300 ALLPUMPS (255 786) www.allpumps.com.au
40Gear PumPs
3600 SERIES
IN[MM]
3600 SERIES CD
E F GH
HOLE DIAMETER
K N NM O P R U V w X KEY PORTSHIGH
NO
OU
TBO
ARD
BEA
RIN
G
11
H & HRV (SPEC G) 15.97
[405]
6.44[163]
0.88[22]
2.75[69]
0.75[19]
0.56[14]
5[127]
2.58[65]
10.34[262]
10.75[273]
3.62[91] 19.57
[497]
1.06[26.9]
4[101]
N/A N/A
.25 SQ. x 1.50
2 NPT TAPPED
HF&HFRV (SPECG)
11.54[293]
4.3[109]
2 NPT FLANGE
17
H & HRV (SPEC G) 16.72
[424]1.83[46]
10.75[273]
3.62[91] 20.33
[516]
2 NPT TAPPED
HF&HFRV (SPECG)
11.54[293]
4.3[109]
2 NPT FLANGE
22 HF&HFRV (SPECG)
18.59[472]
2.2[55]
11.46[291]
12.16[308]
6.41[162]
22.19[563]
4.41[112]
3 NPT FLANGE
35
H&HRV19.53[496] 9.25
[234]5.19[131]
1.5[38]
0.69[17]
9.25[234]
2.15[54]
11.96[303]
15.63[397]
6.88[175] 23.04
[585] 1.437[36.5]
6[152]
.38 SQ. x 1.62
3 NPT TAPPED
HF & HFRV
16.66[423]
7.91[200]
3 NPT FLANGE
58 HF&HFRV (SPECG)
22.51[571]
2.29[58]
13.52[343]
17.35[441]
8.1[205]
26.02[660]
6.28[159]
4 NPT FLANGE
NO
OU
TBO
ARD
BEA
RIN
G
11
HB & HBRV 19.32
[490]
6.44[163]
0.88[22]
2.75[69]
0.75[19]
0.56[14]
5[127]
3.45[87]
13.69[347]
10.75[273]
3.62[91] 22.92
[582]
1[25.4]
4[101]
N/A N/A
.25 SQ. x 1.50
2 NPT TAPPED
HBF & HBFRV
0.62[15]
11.54[293]
4.3[109]
2 NPT FLANGE
17
HB & HBRV 20.07
[509] 0.75[19]
2.7[68]
10.75[273]
3.62[91] 23.67
[601]
2 NPT TAPPED
HBF & HBFRV
11.54[293]
4.3[109]
2 NPT FLANGE
22 HBF & HBFRV
21.57[547]
14.4[366]
12.16[308]
6.41[162]
25.17[639]
4.41[112]
3 NPT FLANGE
35
HB & HBRV 23.69
[601] 9.25[234]
5.19[131]
1.5[38]
0.69[17]
9.25[234]
3.25[82]
16.12[409]
15.63[397]
6.88[174] 27.2
[690] 1.25[31.75]
6[152]
3 NPT TAPPED
HBF & HBFRV
16.66[423]
7.91[200]
3 NPT FLANGE
58 HBF & HBFRV
26.53[673]
17.54[445]
17.35[440]
8.1[205]
30.04[763]
6.28[159] .38 SQ. x 2.25 4 NPT
FLANGE
NO
OU
TBO
ARD
BEA
RIN
G
11
GHB & GHBRV 20.47
[519]
6.44[163]
0.88[22]
2.75[69]
0.75[19]
0.56[14]
5[127]
1.74[44]
14.83[376]
10.75[273]
3.62[91] 24.07
[611]
1[25.4]
4[101] 3.523
[89]10.24[260] .25 SQ. x 1.50
2 NPT TAPPED
GHBF & GHBFRV
0.62[15]
11.54[293]
4.3[109]
2 NPT FLANGE
17
GHB & GHBRV 21.97
[558] 0.75[19]
15.58[395]
10.75[273]
3.62[91] 25.57
[649]
2 NPT TAPPED
GHBF & GHBFRV
11.54[293]
4.3[109]
2 NPT FLANGE
22 GHBF & GHBFRV
23.47[596]
16.33[414]
12.16[308]
6.41[162]
27.07[687]
4.41[112]
3 NPT FLANGE
35
GHB & GHBRV 25.88
[657] 9.25[234]
5.19[131]
1.5[38]
0.69[17]
9.25[234]
2.29[58]
18.31[465]
15.63[397]
6.88[174] 29.39
[746] 1.125[28.58]
6[152] 4.189
[106]11.25[285]
.25 SQ. x 1.50
3 NPT TAPPED
GHBF & GHBFRV
16.66[423]
7.91[200]
3 NPT FLANGE
58 GHBF & GHBFRV
28.72[729]
19.73[501]
17.35[440]
8.1[205]
32.23[818]
6.28[159] .25 SQ. x 1.50 4 NPT
FLANGE
COMPLETE PACKAGED PUMP SOLUTIONS 1300 ALLPUMPS (255 786) www.allpumps.com.au
41GE
AR p
umps
3.25[82]
11.50[292]
3.15[80]
2.65[67]
1.91[48]
3.00[76]
3.00[76]
2.29[58]
R
C
NM
.25 SQ X 1.5 KEY
1.125 [28.58]
6.84 [173]
6.09 [157] 5.10 [129]
PORT
4.19 [106]
1.75 [44]
0.625[15]
11.25 [285]
3.25[82]
11.50[292]
3.15[80]
2.65[67]
1.91[48]
3.94[100]
3.00[76]
3.00[76]
1116
6.40 [162]HI-DRIVE
3.75 [95]LO-DRIVE
1.25 [31.75]
0.625 [15]
R
C
NM
.25 SQ X 2.25 KEY
FOUR HOLES
6.84 [173]
6.09 [157] 5.10 [129]
HI-DRIVE
LO-DRIVE
PORT
6.40[163]
3.75[95] VARIABLE
3.25[82]
11.50[292]
3.15[80]
2.65[67]
1.91[48]
3.00[76]
3.00[76]
2.29[58]
R
C
NM
.25 SQ X 1.5 KEY
1.125 [28.58]
6.84 [173]
6.09 [157] 5.10 [129]
PORT
4.19 [106]
1.75 [44]
0.625[15]
11.25 [285]
3.25[82]
11.50[292]
3.15[80]
2.65[67]
1.91[48]
3.94[100]
3.00[76]
3.00[76]
1116
6.40 [162]HI-DRIVE
3.75 [95]LO-DRIVE
1.25 [31.75]
0.625 [15]
R
C
NM
.25 SQ X 2.25 KEY
FOUR HOLES
6.84 [173]
6.09 [157] 5.10 [129]
HI-DRIVE
LO-DRIVE
PORT
6.40[163]
3.75[95] VARIABLE
3.25[82]
11.50[292]
3.15[80]
2.65[67]
1.91[48]
3.00[76]
3.00[76]
2.29[58]
R
C
NM
.25 SQ X 1.5 KEY
1.125 [28.58]
6.84 [173]
6.09 [157] 5.10 [129]
PORT
4.19 [106]
1.75 [44]
0.625[15]
11.25 [285]
3.25[82]
11.50[292]
3.15[80]
2.65[67]
1.91[48]
3.94[100]
3.00[76]
3.00[76]
1116
6.40 [162]HI-DRIVE
3.75 [95]LO-DRIVE
1.25 [31.75]
0.625 [15]
R
C
NM
.25 SQ X 2.25 KEY
FOUR HOLES
6.84 [173]
6.09 [157] 5.10 [129]
HI-DRIVE
LO-DRIVE
PORT
6.40[163]
3.75[95] VARIABLE
Gear PumPs 3600 SERIES
DimensionsAngled Gears
COMPLETE PACKAGED PUMP SOLUTIONS 1300 ALLPUMPS (255 786) www.allpumps.com.au
42Gear PumPs
3600 SERIES
IN[MM]
3600 SERIES C NM R PORTS
NO
OU
TBO
ARD
BE
ARIN
G
32
HF & HFRV
20.48[520]
12.25[311]
21.40[544] 3 NPT FLANGE
43 22.10[561]
13.07[332]
23.02[585] 3 NPT FLANGE
48 23.19[589]
13.66[347]
24.21[615] 4 NPT FLANGE
NO
OU
TBO
ARD
BE
ARIN
G
32
HBF & HBFRV
23.67[601]
15.44[392]
24.58[624] 3 NPT FLANGE
43 25.32[643]
16.29[414]
26.24[666] 3 NPT FLANGE
48 27.02[686]
17.38[441]
27.93[709] 4 NPT FLANGE
NO
OU
TBO
ARD
BE
ARIN
G
32
GHBF & GHBFRV
25.82[656]
17.59[447]
26.74[679] 3 NPT FLANGE
43 27.43[697]
18.40[467]
28.35[720] 3 NPT FLANGE
48 28.63[727]
19.00[482]
29.55[751] 4 NPT FLANGE
COMPLETE PACKAGED PUMP SOLUTIONS 1300 ALLPUMPS (255 786) www.allpumps.com.au
43GE
AR p
umps
Gear PumPsA SERIES
A Series General Purpose PumpsGeneral Purpose Pumps for Pressure Lubrication, Hydraulic Service, Fuel Supply and General Transfer
Up to 59 GPM • Up to 300 PSIRoper A Series pumps are adaptable to a wide range of applications pumping clean fluids, such as pressure lubrication, hydraulic service, fuel supply or general liquid transfer.
These pumps are designed to operate at standard motor speeds, with provisions for flange or foot mounting. The internal bearings are lubricated by the fluid being pumped. With only two moving parts, the pumps run quietly.
They are manufactured and assembled with close tolerances, and regularly tested to insure dependable performance. Factory assembled for clockwise rotation (facing the pump drive shaft end), most may be reassembled for operation with equal efficiency
in a counter-clockwise rotation.
• Designed to operate at standard motor speeds
• Bi-directional rotation
Quiet-Running Helical GearsAccurate machining insures:
• Proper meshing
• Reduced friction and vibration
• Quiet, efficient operation
• Long life
Long-Lasting Bearing Surfaces• Bearings are special wear-resistant, high-lead
bronze. (Iron and carbon bearings are available.)
• Four heavy duty sleeve bearings give positive support to pumping gears and insure long, efficient service.
Precise, Rugged, Maintenance-Friendly Design• All castings are cast iron.
• Precise manufacturing tolerances provide minimum clearances for maximum pumping efficiency.
• Large, hardened steel dowel pins insure positive alignment between the faceplate, case, and backplate
Features
COMPLETE PACKAGED PUMP SOLUTIONS 1300 ALLPUMPS (255 786) www.allpumps.com.au
44Gear PumPs
A SERIES
Model Number Designation
2(i)
AM(ii)
21(iii)
(i) General Arrangement 1 = Foot Mount
17 = Flange Mount
25 = Base Mount
33 = Close Coupled
(ii) Sealing arrangement AL – Lip Seal AM – Mechanical Seal
AP – Packed Box
(iii) Flowrate in US Gallons/100 Revolutions 005 = 0.002 L/Rev 01 = 0.004 L/Rev 02 = 0.008 L/Rev 03 = 0.011 L/Rev 06 = 0.023 L/Rev 08 = 0.034 L/Rev 12 = 0.049 L/Rev 16 = 0.064 L/Rev 21 = 0.083 L/Rev 27 = 0.102 L/Rev 32 = 0.125 L/Rev 40 = 0.159 L/Rev
2 = Foot Mount with Relief Valve
18 = Flange Mount with Relief Valve
26 = Base Mount with Relief Valve
34 = Close Coupled with Relief Valve
COMPLETE PACKAGED PUMP SOLUTIONS 1300 ALLPUMPS (255 786) www.allpumps.com.au
45GE
AR p
umps
Gear PumPs A SERIES
MODELTHEORETICAL CAPACITY
MAXIMUM SPEEDMAXIMUM FLOw AT MAXIMUM SPEED (0 DISCHARGE PRESSURE)
MAXIMUM PRESSURE
PORT CONNECTION
005 1.9 CC/REV 3600 RPM .41m3/HR 20 Bar 3/8" BSP
01 3.8 CC/REV 3600 RPM .82m3/HR 20 Bar 3/8" BSP
02 7.6 CC/REV 3600 RPM 1.6m3/HR 20 Bar 3/8" BSP
03 11.4 CC/REV 3600 RPM 2.5m3/HR 20 Bar 3/4" BSP
06 22.7 CC/REV 1800 RPM 2.5m3/HR 10 Bar 11/4" BSP
08 34.1 CC/REV 1800 RPM 3.7m3/HR 10 Bar 11/4" BSP
12 49.2 CC/REV 1800 RPM 5.3m3/HR 10 Bar 11/4" BSP
16 64.4 CC/REV 1800 RPM 7.0m3/HR 10 Bar 11/4" BSP
21 83.3 CC/REV 1800 RPM 9.0m3/HR 10 Bar 11/2" BSP
27 102.2 CC/REV 1800 RPM 11.0m3/HR 10 Bar 2" BSP
32 124.9 CC/REV 1800 RPM 13.5m3/HR 10 Bar 2" BSP
40 159.0 CC/REV 1800 RPM 17.2m3/HR 10 Bar 2" BSP
STANDARD OPTION
Housing Cast iron Ductile iron
Shafts Steel
Gears Steel Ductile iron
Bearings Bronze ironCarbon
Packing Graphite Filament Teflon
Lip Seal Nitrile viton
Mechanical Seal Carbon/stainless (Nitrile elastomers)
Viton elastomersTeflon elastomers
Performance
Materials of Construction
N.B.: Not all combinations are available on all pump models.
COMPLETE PACKAGED PUMP SOLUTIONS 1300 ALLPUMPS (255 786) www.allpumps.com.au
46Gear PumPs
A SERIES
PUMP C R PUMP C R
17A-005 5-9/16[141] 18A-01 6-15/16
[176]
18A-005 6-3/4[171] 17A-02 6-3/16
[157]
17A-01 5-13/16[148] 18A-02 7-3/8
[187]
PUMP C R PUMP C R
1A-06 10-15/32[266] 1A-12 11-5/16
[287]
2A-06 12-5/32[309] 2A-12 13
[330]
1A-08 10-3/4[273] 1A-16 11-7/8
[301
2A-08 12-7/16[316] 2A-16 13-9/16
[344]
PUMP B C F N-M R S
1A-21 3[76]
12-5/8[321]
1[25]
9[229]
1-1/2[38]
2A-21 3[76]
1[25]
9[229]
14-5/16[364]
1-1/2[38]
1A-27 3-3/4[95]
13-3/8[340]
1-3/8[35]
9-3/8[238]
2[51]
2A-27 3-3/4[95]
1-3/8[35]
9-3/8[238]
15-1/16[382]
2[51]
1A-32 4-1/2[114]
14-1/8[359]
1-3/4[44]
9-3/4[248]
2[51]
2A-32 4-1/2[114]
1-3/4[44]
9-3/4[248]
15-13/16[402]
2[51]
1A-40 4-1/2[114]
14-1/8[359]
1-3/4[44]
9-3/4[248]
2[51]
2A-40 4-1/2[114]
1-3/4[44]
9-3/4[248]
15-13/16[402]
2[51]
Size 005 Through 02 (flange mounted)
Size 06 Through 16 (foot mounted)
Size 21 Through 16 (foot mounted)R (RELIEF VALVE)
N-M
B
F
4[102]
S (N.P.T. PORT EACH SIDE)
C (PLAIN)
2-1/4MIN.[57]
3/4[19]
2-3/4[70]
FOUR HOLES 9/16 DIA. [14]
1 DIA.[25.4]
3-3/32[79]
2-3/4[70]
6-1/8[156]
1/2[13]
3-1/2[89]
3-1/2[89]
F
1/4 X 1WOODRUFF KEY
R (RELIEF VALVE)
C (PLAIN)
6-3/8[162]
29/32[23]
2-1/4MIN.[57]
3/4[19]
2-3/4[70]
5/8[16]
5/8[16]
1-1/4 DIA. N.P.T. PORTEACH SIDE [32]
FOUR HOLES 9/16 DIA. [14]
1 DIA.[25.4]
4[102]
2-3/4[70]
6-1/8[156]
1/2[13]
3-1/4[83]
3-1/4[83]
1/4 X 1WOODRUFF KEY
2-1/8[54]
2.123 [54]2.122 [54]
2 (RV)[51]
1-5/8[41]
EQUALLY SPACED ON 2-3/4 DIA. B.C.THREE HOLES 1/4-20 UNC THREAD
3-7/8[98]
3/8N.P.T[10]
R(RV)
3-1/8[79]
1-1/2[38]
1/2[12.7]
1/2[13]
C(PLAIN)
1/8 X 1/2WOODRUFF KEY
R (RELIEF VALVE)
N-M
B
F
4[102]
S (N.P.T. PORT EACH SIDE)
C (PLAIN)
2-1/4MIN.[57]
3/4[19]
2-3/4[70]
FOUR HOLES 9/16 DIA. [14]
1 DIA.[25.4]
3-3/32[79]
2-3/4[70]
6-1/8[156]
1/2[13]
3-1/2[89]
3-1/2[89]
F
1/4 X 1WOODRUFF KEY
R (RELIEF VALVE)
C (PLAIN)
6-3/8[162]
29/32[23]
2-1/4MIN.[57]
3/4[19]
2-3/4[70]
5/8[16]
5/8[16]
1-1/4 DIA. N.P.T. PORTEACH SIDE [32]
FOUR HOLES 9/16 DIA. [14]
1 DIA.[25.4]
4[102]
2-3/4[70]
6-1/8[156]
1/2[13]
3-1/4[83]
3-1/4[83]
1/4 X 1WOODRUFF KEY
2-1/8[54]
2.123 [54]2.122 [54]
2 (RV)[51]
1-5/8[41]
EQUALLY SPACED ON 2-3/4 DIA. B.C.THREE HOLES 1/4-20 UNC THREAD
3-7/8[98]
3/8N.P.T[10]
R(RV)
3-1/8[79]
1-1/2[38]
1/2[12.7]
1/2[13]
C(PLAIN)
1/8 X 1/2WOODRUFF KEY
R (RELIEF VALVE)
N-M
B
F
4[102]
S (N.P.T. PORT EACH SIDE)
C (PLAIN)
2-1/4MIN.[57]
3/4[19]
2-3/4[70]
FOUR HOLES 9/16 DIA. [14]
1 DIA.[25.4]
3-3/32[79]
2-3/4[70]
6-1/8[156]
1/2[13]
3-1/2[89]
3-1/2[89]
F
1/4 X 1WOODRUFF KEY
R (RELIEF VALVE)
C (PLAIN)
6-3/8[162]
29/32[23]
2-1/4MIN.[57]
3/4[19]
2-3/4[70]
5/8[16]
5/8[16]
1-1/4 DIA. N.P.T. PORTEACH SIDE [32]
FOUR HOLES 9/16 DIA. [14]
1 DIA.[25.4]
4[102]
2-3/4[70]
6-1/8[156]
1/2[13]
3-1/4[83]
3-1/4[83]
1/4 X 1WOODRUFF KEY
2-1/8[54]
2.123 [54]2.122 [54]
2 (RV)[51]
1-5/8[41]
EQUALLY SPACED ON 2-3/4 DIA. B.C.THREE HOLES 1/4-20 UNC THREAD
3-7/8[98]
3/8N.P.T[10]
R(RV)
3-1/8[79]
1-1/2[38]
1/2[12.7]
1/2[13]
C(PLAIN)
1/8 X 1/2WOODRUFF KEY
COMPLETE PACKAGED PUMP SOLUTIONS 1300 ALLPUMPS (255 786) www.allpumps.com.au
47GE
AR p
umps
Gear PumPs A SERIES
PUMP C R PUMP C R
17A-06 6-25/32[172] 17A-12 7-5/8
[194]
18A-06 8-15/32[215] 18A-12 9-5/16
[237]
17A-08 7-1/16[179] 17A-16 8-3/16
[208]
18A-08 8-3/4[222] 18A-18 9-3/4
[248]
PUMP C B-G R S
17A-21 8-15/16[227]
5-5/16[135]
1-1/2[38]
18A-21 5-5/16[135]
10-5/8[270]
1-1/2[38]
17A-27 9-11/16[246]
5-11/16[144]
2[51]
18A-27 5-11/16[144]
11-3/8[289]
2[51]
17A-32 10-7/16[265]
6-1/16[154]
2[51]
18A-32 6-1/16[154]
12-1/8[308]
2[51]
17A-40 10-7/16[265]
6-1/16[154]
2[51]
18A-40 6-1/16[154]
12-1/8[308]
2[51]
Size 06 Through 16 (flange mounted)
Size 21 Through 40 (flange mounted)
Size 003 (flange mounted) Size 003 (foot mounted)
1-9/16[40]
7-7/8 (RV) [200]
6-11/16 (PLAIN) [170]
3-29/32[99]
1-11/16[43]
2.1232.122[54]
1-9/16[40]
2-1/16(RV) [52]
THREE HOLES 1/4-20 UNC THREADEQUALLY SPACED ON 2-3/4 BIA. B.C.
3-1/8[79]
15/32[12]
1/2[12.7]
1-1/4[32]
1-3/4[44]
1/8 X 1/2 WOODRUFF KEY
3/4 N.P.T. (BOTH SIDES)[19]
2-1/16 (RV)[52]
1-9/16[40]
1-7/8[48]
3-21/32[60]
2-3/8[93]
1-7/8[48]
4-1/2[114]
3/8[10]
1-9/16[40]
4-7/8[124]
1-1/4[32]
7-7/8 (RV) [200]
TWO HOLES13/32 DIA. [10]
1/2[12.7]
6-11/16 (PLAIN) [170]
1/8 X 1/2 WOODRUFF KEY
1-3/8[35]
1-29/32[48]
3/4 N.P.T. (BOTH SIDES) [19]
R (RELIEF VALVE)
B-G3-11/16[94]
7/16[11]
3/16[5]
29/32[23]
S (N.P.T. PORT EACH SIDE)
C (PLAIN)
2-1/4MIN.[57]
3/4[19]
1 DIA.[25.4]
1/4 X 1WOODRUFF KEY
3-1/2[89]
3-1/2[89]
7-1/2 DIA.[191]
SIX HOLES9/16 DIA. [14]EQUALLY SPACEDON 6-7/16 DIA. [164]BOLT CIRCLE
4.000 DIA.3.998
R (RELIEF VALVE)
C (PLAIN)
3-1/4[83]
3-1/4[83]
2-11/16[68]
2-1/4MIN.[57]
3/4[19]
1 DIA.[25.4]
3/16[5]
7/16[11]
29/32[23]
1-1/4 N.P.T.PORT EACH SIDE [32]
3-11/16[94]
7-1/2 DIA. [191]
SIX HOLES 9/16 DIA. [14]EQUALLY SPACED ON 6-7/16 [164] DIA. BOLT CIRCLE
4.000 DIA.3.998
1/4 X 1WOODRUFF KEY
1-9/16[40]
7-7/8 (RV) [200]
6-11/16 (PLAIN) [170]
3-29/32[99]
1-11/16[43]
2.1232.122[54]
1-9/16[40]
2-1/16(RV) [52]
THREE HOLES 1/4-20 UNC THREADEQUALLY SPACED ON 2-3/4 BIA. B.C.
3-1/8[79]
15/32[12]
1/2[12.7]
1-1/4[32]
1-3/4[44]
1/8 X 1/2 WOODRUFF KEY
3/4 N.P.T. (BOTH SIDES)[19]
2-1/16 (RV)[52]
1-9/16[40]
1-7/8[48]
3-21/32[60]
2-3/8[93]
1-7/8[48]
4-1/2[114]
3/8[10]
1-9/16[40]
4-7/8[124]
1-1/4[32]
7-7/8 (RV) [200]
TWO HOLES13/32 DIA. [10]
1/2[12.7]
6-11/16 (PLAIN) [170]
1/8 X 1/2 WOODRUFF KEY
1-3/8[35]
1-29/32[48]
3/4 N.P.T. (BOTH SIDES) [19]
R (RELIEF VALVE)
B-G3-11/16[94]
7/16[11]
3/16[5]
29/32[23]
S (N.P.T. PORT EACH SIDE)
C (PLAIN)
2-1/4MIN.[57]
3/4[19]
1 DIA.[25.4]
1/4 X 1WOODRUFF KEY
3-1/2[89]
3-1/2[89]
7-1/2 DIA.[191]
SIX HOLES9/16 DIA. [14]EQUALLY SPACEDON 6-7/16 DIA. [164]BOLT CIRCLE
4.000 DIA.3.998
R (RELIEF VALVE)
C (PLAIN)
3-1/4[83]
3-1/4[83]
2-11/16[68]
2-1/4MIN.[57]
3/4[19]
1 DIA.[25.4]
3/16[5]
7/16[11]
29/32[23]
1-1/4 N.P.T.PORT EACH SIDE [32]
3-11/16[94]
7-1/2 DIA. [191]
SIX HOLES 9/16 DIA. [14]EQUALLY SPACED ON 6-7/16 [164] DIA. BOLT CIRCLE
4.000 DIA.3.998
1/4 X 1WOODRUFF KEY
1-9/16[40]
7-7/8 (RV) [200]
6-11/16 (PLAIN) [170]
3-29/32[99]
1-11/16[43]
2.1232.122[54]
1-9/16[40]
2-1/16(RV) [52]
THREE HOLES 1/4-20 UNC THREADEQUALLY SPACED ON 2-3/4 BIA. B.C.
3-1/8[79]
15/32[12]
1/2[12.7]
1-1/4[32]
1-3/4[44]
1/8 X 1/2 WOODRUFF KEY
3/4 N.P.T. (BOTH SIDES)[19]
2-1/16 (RV)[52]
1-9/16[40]
1-7/8[48]
3-21/32[60]
2-3/8[93]
1-7/8[48]
4-1/2[114]
3/8[10]
1-9/16[40]
4-7/8[124]
1-1/4[32]
7-7/8 (RV) [200]
TWO HOLES13/32 DIA. [10]
1/2[12.7]
6-11/16 (PLAIN) [170]
1/8 X 1/2 WOODRUFF KEY
1-3/8[35]
1-29/32[48]
3/4 N.P.T. (BOTH SIDES) [19]
R (RELIEF VALVE)
B-G3-11/16[94]
7/16[11]
3/16[5]
29/32[23]
S (N.P.T. PORT EACH SIDE)
C (PLAIN)
2-1/4MIN.[57]
3/4[19]
1 DIA.[25.4]
1/4 X 1WOODRUFF KEY
3-1/2[89]
3-1/2[89]
7-1/2 DIA.[191]
SIX HOLES9/16 DIA. [14]EQUALLY SPACEDON 6-7/16 DIA. [164]BOLT CIRCLE
4.000 DIA.3.998
R (RELIEF VALVE)
C (PLAIN)
3-1/4[83]
3-1/4[83]
2-11/16[68]
2-1/4MIN.[57]
3/4[19]
1 DIA.[25.4]
3/16[5]
7/16[11]
29/32[23]
1-1/4 N.P.T.PORT EACH SIDE [32]
3-11/16[94]
7-1/2 DIA. [191]
SIX HOLES 9/16 DIA. [14]EQUALLY SPACED ON 6-7/16 [164] DIA. BOLT CIRCLE
4.000 DIA.3.998
1/4 X 1WOODRUFF KEY
1-9/16[40]
7-7/8 (RV) [200]
6-11/16 (PLAIN) [170]
3-29/32[99]
1-11/16[43]
2.1232.122[54]
1-9/16[40]
2-1/16(RV) [52]
THREE HOLES 1/4-20 UNC THREADEQUALLY SPACED ON 2-3/4 BIA. B.C.
3-1/8[79]
15/32[12]
1/2[12.7]
1-1/4[32]
1-3/4[44]
1/8 X 1/2 WOODRUFF KEY
3/4 N.P.T. (BOTH SIDES)[19]
2-1/16 (RV)[52]
1-9/16[40]
1-7/8[48]
3-21/32[60]
2-3/8[93]
1-7/8[48]
4-1/2[114]
3/8[10]
1-9/16[40]
4-7/8[124]
1-1/4[32]
7-7/8 (RV) [200]
TWO HOLES13/32 DIA. [10]
1/2[12.7]
6-11/16 (PLAIN) [170]
1/8 X 1/2 WOODRUFF KEY
1-3/8[35]
1-29/32[48]
3/4 N.P.T. (BOTH SIDES) [19]
R (RELIEF VALVE)
B-G3-11/16[94]
7/16[11]
3/16[5]
29/32[23]
S (N.P.T. PORT EACH SIDE)
C (PLAIN)
2-1/4MIN.[57]
3/4[19]
1 DIA.[25.4]
1/4 X 1WOODRUFF KEY
3-1/2[89]
3-1/2[89]
7-1/2 DIA.[191]
SIX HOLES9/16 DIA. [14]EQUALLY SPACEDON 6-7/16 DIA. [164]BOLT CIRCLE
4.000 DIA.3.998
R (RELIEF VALVE)
C (PLAIN)
3-1/4[83]
3-1/4[83]
2-11/16[68]
2-1/4MIN.[57]
3/4[19]
1 DIA.[25.4]
3/16[5]
7/16[11]
29/32[23]
1-1/4 N.P.T.PORT EACH SIDE [32]
3-11/16[94]
7-1/2 DIA. [191]
SIX HOLES 9/16 DIA. [14]EQUALLY SPACED ON 6-7/16 [164] DIA. BOLT CIRCLE
4.000 DIA.3.998
1/4 X 1WOODRUFF KEY
COMPLETE PACKAGED PUMP SOLUTIONS 1300 ALLPUMPS (255 786) www.allpumps.com.au
48Gear PumPs
A SERIES
PUMP B C F N-M R S
1AE-19 3[76]
12-5/8[321]
1[25]
9[229]
1-1/2[38]
2AE-19 3[76]
1[25]
9[229]
14-13/16[376]
1-1/2[38]
1AE-29 4-1/2[114]
14-1/8[359]
1-3/4[44]
9-3/4[248]
2[51]
2AE-29 4-1/2[114]
1-3/4[44]
9-3/4[248]
15-13/16[402]
2[51]
Size 19 Through 29 (foot mounted)
Size 54 (foot mounted)
Size 75 (foot mounted)
Ø1.00[25.4]
1-7/8 [48]
3/4[19]
1/4 x 1 WOODRUFF KEY
2 N.P.T. (OPPOSITE SIDE) [51]
2 N.P.T. [51]
FOUR HOLES 9/16 DIA. [14]
1/2 [12.7]
7-1/8[181]
6 [152] 6 [152]
5[127] 4-3/32
[104]
5-3/8 [137] 5-3/8 [137]
4-1/2 [114]
1-3/4 [44]
1-3/4 [44]
12 [305]
9-3/4 [248]
20-5/16 (RELIEF VALVE) [516]
18-5/8 (PLAIN) [473]
1-7/8 [48]
N-M
R(RELIEF VALVE)
B
3/4[19]
C(PLAIN)
Ø1.00[25.4]
3-3/32[79]
4[102]
S(N.P.T. PORT EACH SIDE)
FOUR HOLES 9/16 DIA. [14]
2-3/4 [70] 2-3/4 [70]
3-1/2 [89] 3-1/2 [89]
1/2 [12.7]
6-1/8[156]
1/4 x 1WOODRUFF KEY
4-3/32 [104]
14-1/4 [362]
24-13/16 (RELIEF VALVE) [630]
1-3/4 [44]
1-3/4 [44]
4-1/2 [114]
Ø1.00[25.4]
1-7/8 [48]
23-1/8 (PLAIN) [587]
3/4 [19]
1/4 x 1WOODRUFF KEY
2-1/2 N.P.T. BOTH SIDES [64]
FOUR HOLES 9/16 DIA. [14]
5-3/8 [137]
6 [152] 6 [152]
1/2 [12.7]
5[127]
7-1/8[181]
5-3/8 [137]
Ø1.00[25.4]
1-7/8 [48]
3/4[19]
1/4 x 1 WOODRUFF KEY
2 N.P.T. (OPPOSITE SIDE) [51]
2 N.P.T. [51]
FOUR HOLES 9/16 DIA. [14]
1/2 [12.7]
7-1/8[181]
6 [152] 6 [152]
5[127] 4-3/32
[104]
5-3/8 [137] 5-3/8 [137]
4-1/2 [114]
1-3/4 [44]
1-3/4 [44]
12 [305]
9-3/4 [248]
20-5/16 (RELIEF VALVE) [516]
18-5/8 (PLAIN) [473]
1-7/8 [48]
N-M
R(RELIEF VALVE)
B
3/4[19]
C(PLAIN)
Ø1.00[25.4]
3-3/32[79]
4[102]
S(N.P.T. PORT EACH SIDE)
FOUR HOLES 9/16 DIA. [14]
2-3/4 [70] 2-3/4 [70]
3-1/2 [89] 3-1/2 [89]
1/2 [12.7]
6-1/8[156]
1/4 x 1WOODRUFF KEY
4-3/32 [104]
14-1/4 [362]
24-13/16 (RELIEF VALVE) [630]
1-3/4 [44]
1-3/4 [44]
4-1/2 [114]
Ø1.00[25.4]
1-7/8 [48]
23-1/8 (PLAIN) [587]
3/4 [19]
1/4 x 1WOODRUFF KEY
2-1/2 N.P.T. BOTH SIDES [64]
FOUR HOLES 9/16 DIA. [14]
5-3/8 [137]
6 [152] 6 [152]
1/2 [12.7]
5[127]
7-1/8[181]
5-3/8 [137]
Ø1.00[25.4]
1-7/8 [48]
3/4[19]
1/4 x 1 WOODRUFF KEY
2 N.P.T. (OPPOSITE SIDE) [51]
2 N.P.T. [51]
FOUR HOLES 9/16 DIA. [14]
1/2 [12.7]
7-1/8[181]
6 [152] 6 [152]
5[127] 4-3/32
[104]
5-3/8 [137] 5-3/8 [137]
4-1/2 [114]
1-3/4 [44]
1-3/4 [44]
12 [305]
9-3/4 [248]
20-5/16 (RELIEF VALVE) [516]
18-5/8 (PLAIN) [473]
1-7/8 [48]
N-M
R(RELIEF VALVE)
B
3/4[19]
C(PLAIN)
Ø1.00[25.4]
3-3/32[79]
4[102]
S(N.P.T. PORT EACH SIDE)
FOUR HOLES 9/16 DIA. [14]
2-3/4 [70] 2-3/4 [70]
3-1/2 [89] 3-1/2 [89]
1/2 [12.7]
6-1/8[156]
1/4 x 1WOODRUFF KEY
4-3/32 [104]
14-1/4 [362]
24-13/16 (RELIEF VALVE) [630]
1-3/4 [44]
1-3/4 [44]
4-1/2 [114]
Ø1.00[25.4]
1-7/8 [48]
23-1/8 (PLAIN) [587]
3/4 [19]
1/4 x 1WOODRUFF KEY
2-1/2 N.P.T. BOTH SIDES [64]
FOUR HOLES 9/16 DIA. [14]
5-3/8 [137]
6 [152] 6 [152]
1/2 [12.7]
5[127]
7-1/8[181]
5-3/8 [137]