32lg40 training manualdiagramas.diagramasde.com/otros/32lg40-presentation.pdf6 lcd dv august 2008...

32LG4032LG40

Model : 32LG40 32” CLASS LCD HDTV w/ BUILT-IN DVD PLAYER

(31.5" diagonal)Direct View LCDDirect View LCDWith built in DVD PlayerWith built in DVD Player

TRAINING MANUALTRAINING MANUAL

Original 08/12/2008Updated 10/13/2010

LCD DV August 2008 32LG402

OUTLINEOUTLINE

• Main (Digital) Board

• T-CON Board• Ballast Board

Circuit Board Operation, Troubleshooting of :• Switch mode Power Supply

Section 1

Section 2

Contact Information, Preliminary Matters, Specifications,LCD Overview, General Troubleshooting Steps, Signal Distribution, Disassembly Instructions and Voltages


32LG40 LCD Direct View Display

Section 1

This Section will cover Contact Information and remind the Technician of Important Safety Precautions for the Customers Safety as well as the Technician and the Equipment.

Basic Troubleshooting Techniques which can save time and money sometimes can be overlooked. These techniques will also be presented.

This Section will get the Technician familiar with the Disassembly, Identification and Layout of the LCD Display Panel.

At the end of this Section the Technician should be able to Identify the Circuit Boards and have the ability and knowledge necessary to remove and replace safely any Circuit Board or Assembly.

Overview of Topics to be DiscussedOverview of Topics to be Discussed


Important Safety NoticeImportant Safety Notice

The information in this training manual is intended for use by persons possessing an adequate background in electrical equipment, electronic devices, and mechanical systems. In any attempt to repair a major Product, personal injury and property damage can result. The manufacturer or seller maintains no liability for the interpretation of this information, nor can it assume any liability in conjunction with its use. When servicing this product, under no circumstances should the original design be modified or altered without permission from LG Electronics. Unauthorized modifications will not only void the warranty, but may lead to property damage or user injury. If wires, screws, clips, straps, nuts, or washers used to complete a ground path are removed for service, they must be returned to their original positions and properly fastened.

CautionCautionTo avoid personal injury, disconnect the power before servicing this product. If electrical power is required for diagnosis or test purposes, disconnect the power immediately after performing the necessary checks. Also be aware that many household products present a weight hazard. At least two people should be involved in the installation or servicing of such devices. Failure to consider the weight of an product could result in physical injury.

Preliminary Matters (The Fine Print)Preliminary Matters (The Fine Print)


Today’s sophisticated electronics are electrostatic discharge (ESD) sensitive. ESD can weaken or damage the electronics in a manner that renders them inoperative or reduces the time until their next failure. Connect an ESD wrist strap to a ground connection point or unpainted metal in the product. Alternatively, you can touch your finger repeatedly to a ground connection point or unpainted metal in the product. Before removing a replacement part from its package, touch the anti-static bag to a ground connection point or unpainted metal in the product. Handle the electronic control assembly by its edges only. When repackaging a failed electronic control assembly in an anti-static bag, observe these same precautions.

Regulatory InformationRegulatory Information

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna; Increase the separation between the equipment and the receiver; Connect the equipment to an outlet on a different circuit than that to which the receiver is connected; or consult the dealer or an experienced radio/TV technician for help.

ESD NoticeESD Notice (Electrostatic Static Discharge)(Electrostatic Static Discharge)


Customer Service (and Part Sales) (800) 243-0000

Technical Support (and Part Sales) (800) 847-7597

USA Website (GSFS) http://gsfs-america.lge.com

Customer Service Website http://www.us.lgservice.com

Knowledgebase Website http://lgtechassist.com

LG Web Training https://lge.webex.com

LG CS Academy http://ln.lge.com/ilearn

Published August 2008 by LG Technical Support and TrainingLG Electronics Alabama, Inc.

201 James Record Road, Huntsville, AL, 35813.

32LG40, 32LH30, 37LH55, 42LG60, 42LG70, 42LH20, 42LH40, 42LH50, 42LH90, 42SL80, 47LG90, 47LH85, 42LE5500, 47LE850042PG20, 42PJ350, 42PQ20, 42PQ30, 50PG20, 50PJ350, 50PK250, 50PK750, 50PS80, 50PS60, 60PK750, 60PS11, 60PS60, 60PS80

LCD-DV:

PLASMA:

Also available on the Plasma Page:PDP Panel Alignment Handbook, Schematics with Bookmarks

Plasma Control Board ROM Update (Jig required)

LG Contact InformationLG Contact Information

Presentations with Audio/Video and Screen Marks

New Training Materials on New Training Materials on the Learning Academy sitethe Learning Academy site

New: 2010 Models Software Downloads Technical Assistance

http://136.166.4.200


Safety and Handling Regulations

1. Approximately 20 minute pre-run time is required before any adjustments are performed. 2. Refer to the Voltage Sticker on the Switch Mode Power Supply silk screening. (+/- ½ volt). 3. Be cautious of electric shock from the Backlight section, it uses high voltage AC. Check that

the Power Supply and Drive Circuits are completely discharged because of residual current stored before Circuit Board removal.

4. C-MOS circuits are sensitive to static electricity. Use caution when dealing with these IC and circuits.

5. Exercise care when making voltage and waveform checks to prevent costly short circuits from damaging the unit.

6. Be cautious of lost screws and other metal objects to prevent a possible short in the circuitry.

1. Check the appearance of the Replacement Panel and Circuit Boards for both physical damage and part number accuracy.

2. Check the model label. Verify model names and board model matches.3. Check details of defective condition and history. Example: Oscillator failure dead set, etc…

Checking Points to be Considered

OVERVIEW SECTIONOVERVIEW SECTION


Basic Troubleshooting StepsBasic Troubleshooting Steps

Define, Localize, Isolate and Correct

•Define Look at the symptom carefully and determine what circuits could be causing the failure. Use your senses Sight, Smell, Touch and Hearing. Look for burned parts and check for possible overheated components. Capacitors will sometimes leak dielectric material and give off a distinct odor. Frequency of power supplies will change with the load, or listen for relay closing etc. Observation of the front Power LED may give some clues.

•Localize After carefully checking the symptom and determining the circuits to be checked and after giving a thorough examination using your senses the first check should always be the DC Supply Voltages to those circuits under test. Always confirm the supplies are not only the proper level but be sure they are noise free. If the supplies are missing check the resistance for possible short circuits.

•Isolate To further isolate the failure, check for the proper waveforms with the Oscilloscope to make a final determination of the failure. Look for correct Amplitude Phasing and Timing of the signals also check for the proper Duty Cycle of the signals. Sometimes “glitches” or “road bumps” will be an indication of an imminent failure.

•Correct The final step is to correct the problem. Be careful of ESD and make sure to check the DC Supplies for proper levels. Make all necessary adjustments and lastly always perform a Safety AC Leakage Test before returning the product back to the Customer.


This section of the manual will discuss the specifications of the 32LG40“Thin” LCD Direct View Display Panel.

32LG40 Product Information32LG40 Product Information

Side View


Basic SpecificationsBasic Specifications

•720p HD Resolution • 12,000:1 Dynamic Contrast Ratio • Side-loading Progressive Scan DVD Player • Super Multi-Format • 3x HDMI™ 1.3 • AV Mode (Cinema, Sports, Game) • Clear Voice • SimpLink™ Connectivity • Invisible Speaker System • Expert Mode • PC Input • Swivel Stand (Manual)


HD RESOLUTION 720p HD Resolution Pixels: 1365 (H) × 768 (V)High definition television is the highest performance segment of the DTV system used in the US. It’s a wide screen, high-resolution video image, coupled with multi-channel, compact-disc quality sound.

Pixel Count to Resolution ComparisonsPixel Count to Resolution Comparisons

FORMATS480I480P1080I720P1080P

InterlacedProgressiveInterlacedProgressiveProgressive

Interlaced2 Fields to make a Frame

ProgressiveEach Field is a Frame

Think of sync as the Panels “Refresh Rate”

240 Lines480 Lines540 Lines720 Lines1080 Lines

NTSCSDHDHDHD

Possible FrameRates:24FPS30FPS60FPS

768720P Panel720P Logo

BASICPIXEL COUNTS

720P Panel1365 (H) × 768 (V)

1080P Panel1920 (H) x 1080 (V)



INVISIBLE SPEAKER SYSTEMLG’s 2008 line of TVs include a unique invisible speaker system, tuned by renowned audio expert, Mr. Mark Levinson. Speakers are embedded in strategic spots behind the front cabinet and use minute vibrations to turn the entire front bezel into the speaker system. The result is a clean, polished look, and enhanced audio by increasing the “sweet spot” giving a wider sound field.

BUILT-IN SIDE LOADING PROGRESSIVE SCAN DVD PLAYERSave space with the built-in progressive scan DVD player. Side loading player upconvertsDVDs to near 720p resolution and features LG “Super-Multi” technology which plays back almost any recordable disc based media.

LG SIMPLINK™ MULTI-DEVICE CONTROL Allows for convenient control of other LG SimpLink products using the existing HDMI connection.

HDMI (1.3 Deep Color) Digital multi-connectivity HDMI (1.3 Deep color) provides a wider bandwidth (340MHz, 10.2Gbps) than that of HDMI 1.2, delivering a broader range of colors, and also drastically improves the data-transmission speed.



AV Mode "One click" - Cinema, Sports, Game mode.TAKE IT TO THE EDGE is a true multimedia TV with an AV Mode which allows you to choose from 3 different modes of Movies, Video Games and Sports by a single click of a remote control.

Clear Voice Clearer dialogue sound Automatically enhances and amplifies the sound of the human voice frequency range to provide high-quality dialogue when background noise swells.

Save Energy, Save MoneyHome electronic products use energy when they're off to powerfeatures like clock displays and remote controls. Those that haveearned the ENERGY STAR use as much as 60% less energy toperform these functions, while providing the same performance at thesame price as less-efficient models. Less energy means you pay lesson your energy bill. Draws less than 1 Watt in stand by.


Remote ControlRemote Control

1 2 3

4 5 6

7 8 9

0

VOL CH

FAV

MUTE

PAGE

LG

TOP PORTION

BOTTOM PORTIONp/n: MKJ40653818


Side Input Jacks

Rear and Side Input JacksRear and Side Input Jacks

USB

HDMI

CompositeA/V

Main Board

Orientation

ComponentY Pr/Pb

Optical AudioRGB (PC) Audio

RGB (PC)HDMI

RS232Service Only

Remote In

AudioOut

Composite

Current Software Release32LG40-UA-v03.12_080711_Download.epk


Accessing the Service MenuAccessing the Service Menu

REMOTETOP PORTION

SIDE KEYS

Note: Dependant upon the Software Version, a Password may be required to enter the Service Menu.

If a password is required, enter0000

To access the Service Menu.1) Turn the Set On2) Simultaneously, Press and

“Hold” the Menu Key on the Side Key pad and Press and “Hold” the Menu Key on the Remote approximately 5 seconds.

3) If Customer’s Menu appears, continue to hold until it disappears.

4) The Service Menu appears


1) Create an LG_DTV folder on the USB Flash Drive

2) Copy new software (xxx.epk) to "LG_DTV" folder. Make sure to have correct software file.

3) With TV turned on, insert USB flash drive.4) You can see the message

“TV Software Upgrade” (See figure to right)5) Cursor left and highlight "START" Button and

push “Enter” button using the remote control. 6) You can see the download progress Bar.7) Do not unplug until unit has automatically

restarted.8) When download is completed, you will see

“COMPLETE”. 9) Your TV will be restarted automatically.

Software Upgrade ProcedureSoftware Upgrade Procedure

Shows the Currently Installed Version

Shows the Software Version

found on the USB Flash

Drive

Shows the Software file found on the USB Flash

Drive

* CAUTION: Do not remove AC power or the USB Flash Drive. Do not turn off Power, during the upgrade process.


32LG40 Product Measurements32LG40 Product Measurements


This section of the manual will discuss troubleshooting.

Upon completion of this section the Technician will have a better understanding of how to diagnosis and resolve problems.

TROUBLESHOOTING SECTIONTROUBLESHOOTING SECTION


Removing the Back CoverRemoving the Back Cover

The Stand does not need to be removed. Remove the 18 screws shown by arrows.Pay attention to the size and type of screw as there are many different types.

Putting in the improper screw when reassembling may Cause damage.


Circuit Board LayoutCircuit Board Layout Panel p/n EAJ41825601

SideInputs

SideControls

LVDSCables

SpeakersSpeaker rattle.

1) Tighten screws at bottom of cabinet2) Tighten screws holding woofers

T-CON p/nEAT56801301

Ballast p/nEAY56797501


Invisible Speaker System LayoutInvisible Speaker System Layout

Bottom View of Woofer Ports

Woofers

Tweeters Tweeters

Stand Removed

Speaker rattle.1) Tighten screws at bottom of cabinet2) Tighten screws holding woofers


POWER SUPPLY POWER SUPPLY SECTIONSECTION

P201

AC IN

P203 To Main

F1005A/250V

AC IN

To Ballast1 2

ErrorWM-D1INV On/OffBR1GndGndGndGndGnd24V24V24V24V24V

1413121110987654321

n/c

F1013.15A/250V334V Actual

1

Hot Ground

n/cPWR-DIMINVOn/OffACDGndGnd5.2V5.2VGnd12VGnd16.5V

24222018161412108642

Fixed VoltsBR1POWER-ONERRORGndGnd5.2V5.2VGnd12VGnd16.5V

2321191715131197531

SMPS Board LayoutSMPS Board Layout


Power Supply (SMPS) Power Supply (SMPS) Board DrawingBoard Drawing P201

AC IN

P203 To Main

F1005A/250V

AC IN

To Ballast

16.5VGnd12VGnd5.2V5.2VGndGndACDINVOn/OffPWR-DIMn/c

24681012141618202224

16.5VGnd12VGnd5.2V5.2VGndGndERRORPOWER-ONBR1fixedV

1357911131517192123

ErrorWM-D1INV On/OffBR1GndGndGndGndGnd24V24V24V24V24V

1413121110987654321

F1013.15A/250V334V Actual


Power Supply P201 Control Signals from Main Board P800Power Supply P201 Control Signals from Main Board P800


Power Supply Board Test (1) All Board DisconnectedPower Supply Board Test (1) All Board Disconnected

The Power Supply “MUST” be producing STAND-BY +5V before proceeding.

P201 Connector disconnected from the Main BoardAC: Not applied when adding jumper. Applied when making test.

With Power Supply disconnected from other Boards and AC applied, confirm that the Power Supply is producing 5V from either Pins 9, 10, 11 or 12. If not, check fuse. If fuse OK and no 5V, replace Power Supply. If 5V OK then continue.

1st short either pin 9, 10, 11 or 12 (5V) to Pin 19 (PWR) using a 10K resistor.

This turns on the power supply.Confirm that the other low voltage power supplies are activated.

Pins 1 and 2 (16V)Pins 5 and 6 (12V)Pin 18 (AC Detect) goes highFuse F101 Check for 350V (Ballast Voltage)

If any voltage missing, replace Power Supply.

+5V


Power Supply Board Test (2) Checking the BacklightsPower Supply Board Test (2) Checking the Backlights

If the 1st test was successful, continue. Leave original 10K in place.

2nd: To test the Backlights, leave the 10K jumper in place. Plug up the Back light plug P203. Apply AC Power.

Observe the Backlights.If normal, LED1 on the Ballast Board should turn on first, then backlights should turn on and LED1 should go off..

If no backlight activity, confirm the Fuse F101 has approx. 350V on both sides.If on one side, check fuse for open. If no 350V, replace Power Supply.

If 300V present, check P203 for 24V on Pins 1~5. Check P203 Pin 12 for at least 3V (Inverter On/Off).

If yes, confirm Connectors to backlight OK, if OK, then panel defective.

+5V

P2 Connector disconnected from the Main BoardAC: Not applied when adding jumper. Applied when make test.

Ballast will not run if either of the Backlight plugs are removed.


Power Supply Board RemovalPower Supply Board Removal

Disconnect P203, P201 and AC InRemove the 4 screws indicated in the red circles.


Power Supply Connector P201 Odd Pins Voltage and Diode CheckPower Supply Connector P201 Odd Pins Voltage and Diode Check

Resistance taken in Diode Mode with Connectors Removed

0.31V16V0V16.5V1

GndGndGndGnd3

1.69V11.8V0V12V5

GndGndGndGnd7

0.34V5.15V5.15V5.2V9

0.34V5.15V5.15V5.2V11

GndGndGndGnd13

GndGndGndGnd15

1.26VGndGndERR17

OL2.86V0VPWR19

OL1.68V0VBR121

OL3.2V0VN/C23

Diode CheckRun STBYLabelPin

P201 "SMPS" to P800 "Main Board"

GndGndGndGnd4

0.31V16V0V16.5V2

1.69V11.8V0V12V6

0VGndGndGnd8

0.34V5.15V5.15V5.2V10

0.34V5.15V5.15V5.2V12

GndGndGndGnd14

GndGndGndGnd16

OL4.57V5.05VACD18

OL3.29V0VINV On/Off20

OL3.38V0VPWM-DIM22

OL0V0VN/C24



Power Supply Connector P203 Voltage and Diode CheckPower Supply Connector P203 Voltage and Diode Check


OL0V0VERROR14

OL3.40V0VPWM-DIM13

OL3.45V0VINV On-Off12

OL1.67V0VBR111

GndGndGndGnd10

GndGndGndGnd9

GndGndGndGnd8

GndGndGndGnd7

GndGndGndGnd6

0.33V24.52V0V24V5

0.33V24.52V0V24V4

0.33V24.52V0V24V3

0.33V24.52V0V24V2

0.33V24.52V0V24V1


P203 "SMPS" to MCN1 "Ballast Board"


MAIN BOARD SECTIONMAIN BOARD SECTION

P800

P901

P900

P904

P401

P500

P902 P200No ConnectionSoftware DownloadLVDS To T-CON

ToPower

To DVD

To DVD

To DVD

ToFt Keys

To SPK

Reset BCM

IC407 Micro

SideInputs

HDMI

USBTUNERLD800

IC100BCM

IC101Flash

MemoryBCM IC803 9V Reg

IC809 A2.6V BCM Reg

IC807 5V Reg

IC806 A3.3V BCM

IC802 3.3V Reg

IC600HDMI Selector

IC800CVBS Amp

IC304DDR VTT

IC301

IC303

IC300

IC302

IC400 BCM Reset

Q801 5V Sub Switch

IC501 Audio Processorand Output

16V Pins 49~52

IC602 HDMI EDID

IC502Audio Selector

IC402Serial PortInterface

IC201USB 3.3V

X40024Mhz

Q800 SIF

IC601 HDMI EDID

X20054Mhz

Dual Data Registers

IC405 Micro Reset

Q400 Micro Reset

Q802 5V Sub Switch Control

If odd Video problems are

found, use some freeze spray

about IC100 and its circuits,

If video returns to normal, Board

needs to be replaced.


Main Board (Front Side) Regulator Checks 1 of 2Main Board (Front Side) Regulator Checks 1 of 2

3.39V0VReset (Lo-Hi)OUT3

9V0V+9VOUT3GndGndGndGnd2

GndGndGndGnd23.4V0VD3.3V_BCMIN1

12V0V+12VIN1RUNSTBYNAMEFUNCTIONPIN

RUNSTBYNAMEFUNCTIONPINRESET GENERATOR TO IC401 3.3BCM (On Back)IC400

+9V RegulatorIC8031.29V0VDDRO_VTTOn/Off Control4

3.2V0V+5V_SUBIN32.6V0VD2.6V_BCMIN5,6,7

GndGndGndOUT21.29V0VDDRO_VTTOUT3,8

5V0V+3.3VGnd1RUNSTBYNAMEFUNCTIONPIN

RUNSTBYNAMEFUNCTIONPIN2.6V BCMIC304

+3.3V Regulator (3.3V TMDS_SW)IC8023.1V0V+3.3VOUT8

0.6V0.6VReset (Lo-Hi)OUT35V0VUSB_PWR_Out_1OUT7

GndGndGndGnd23.4V0VBCM DDR PowerOn/Off Control3

3.41V3.41V3.3V_MICONIN15V0V+5VIN2

RUNSTBYNAMEFUNCTIONPINRUNSTBYNAMEFUNCTIONPIN

RESET GENERATOR FOR Q400 Micro ResetIC405USB PowerIC201


Main Board (Front Side) Regulator Checks 2 of 2Main Board (Front Side) Regulator Checks 2 of 2

GndGndGndGnd11,18,19,20

n/cn/cn/cn/c14,15

2.66V0VD2.6V_BCMOUT1,2,3,4,5

3.41V0VPower_CTL_2.6VOn/Off Control17

4.98V0.36V+5V_SUBIN6,7,8,10

GndGndGndGndERUNSTBYNAMEFUNCTIONPIN

0V0V3.3VVST_MICONVccCD2.6V/A2.6V_BCM RegulatorIC809

0.6V0.6VResetResetBGndGndGndGnd5

RUNSTBYNAMEFUNCTIONPINn/cn/cn/cn/c4

RESET GENERATOR FOR MICRO IC407Q4005V0V+5VOUT3

GndGndGndGndE3.4V0VPower_CTL_3.3VOn/Off Control2

5V0VST_5VPull DownC8.9V0V+9VIN1

3.29V0VRL_ONOn/Off ControlBRUNSTBYNAMEFUNCTIONPIN

RUNSTBYNAMEFUNCTIONPIND3.3V/A3.3V_BCM RegulatorIC807

CONTROLLER for 5V SUB SWITCH Q801Q8023.4V0.1VD3.3V_BCMOUT4

5V0V+5V_SUBOUT5,6,7,8GndGndGndGnd3

0.28V0VQ802On/Off Control2,45V0.36V+5V_SUBIN2

5V0VST_5VIN1,33.4V0VPower_CTL_3.3VOn/Off Control1


5V SUB SWITCHQ801D3.3V/A3.3V_BCM Regulator turns on LD800IC806


Main Board (Back View) Regulator LayoutMain Board (Back View) Regulator Layout

TUNERTU800

P800

P901

P900

P904

P401

P500

P902P200

IC8083.3V Micon

1

16

IC102HDCP KEY

IC403NVRAM

IC805 A1.2V BCM Reg

IC702EEPROM

Q901 LVDS 12V Switch

Q900Turns on Q901

IC406Micro

EEPROM

X200

SideInputs

IC408SIF Select DVD/BCM

IC701Side HDMI EDID

IC801 1.8V Reg

IC401 BCM Reset

Silk Screen for Pin 1 wrong IC805


Main Board (Back Side) Regulator ChecksMain Board (Back Side) Regulator Checks

Screen Print for Pin No is incorrect, use IC

GndGndGndGnd11,12,18,19,20

0V0Vn/cn/c13, 14,15,16

12.36V0VLVDS 12VOUT5,6,7,81.29V0VD1.2V_BCMOUT1,2,3,4,5

6.16V0VQ900On/Off Control2,43.41V0VPower_CTL_1.2VOn/Off Control17

12.36V0V12VIN1,35V0.38V+5V_SUBIN6,7,8,10


LVDS 12V SWITCHQ901D1.2V/A1.2V BCM REGULATORIC805

0V0VGndGndE3.29V0.26V3.3V_TMDS_SWIN3

0V0VLVDS Switch ControlPull Down 12VC1.8V0V'+1.8V_NTPOUT2

0.75V0VLVDS_PANEL_CTRLControlBGndGndGndGnd1


LVDS 12V SWITCH CONTROLLER Q901Q900+1.8V_NTP REGULATORIC801

GndGndGndGnd43.4V0VBCM_RESETOUT6

3.43V3.43V3.3VST_MICONOUT33.4V0VReset from IC400On/Off Control1

5V5VST_5VIN23.41V0VD3.3V_BCMIN14


ST-BY 3.3V DC-DC CONVERTERIC808BCM RESETIC401


2.4Vp/p24Mhz

With set on or off

X400

Main Board X400 and X200 CheckMain Board X400 and X200 Check

Main BoardX400 Location

Main BoardX200 Location

MAIN Board

660mVp/p54Mhz

Only when set is on

X200

1.49V

1.49V

1.49V

1.49V

TP Use Crystal Side R232 or R233

TP Use Crystal leg top or bottom

IC407Micro


Main Board Tuner Video and SIF Output Check Pin LocationMain Board Tuner Video and SIF Output Check Pin Location

For Easy Access, pop the shield off the tuner

If you leave the shield on you can still access the same pins.

Be careful not to accidentally ground out your test lead on the

shield.

Pin 16 Composite Video

Pin 14 Audio SIF

Pin 3 Tuner B+ (5V)


MAIN Board

Main Board Tuner Video and SIF Output CheckMain Board Tuner Video and SIF Output Check

TunerLocation

1Vp/p 20uSec rate

Pin 16 “Video”Signal

Pin 14 “SIF”Signal

850mVp/p

Using SMTP Color Bar Input

Using SMTP Color Bar Input


Main Board LVDS P902 Output CheckMain Board LVDS P902 Output Check

P902Location

To confirm that the Main Board is outputting Picture Content signals, check P902 (LVDS) cable for output. Check 11~20. This signals vary from each other, but looking for signals like the ones shown below on any of these pins confirm the output of video content.This signal is using standard SMTE Color Bar output from a generator as the input source.

Pin 11

Pin 16

MAIN Board

Remember there are actually10 pins with LVDS signals.This only represents twoWaveforms as an example.


Main Board RemovalMain Board Removal

Disconnect P902, P800, P901, P900, P904, P401 and P500Note: In the top right is a Connector P200. This is an open connection. (Software Upgrades)Remove the 2 screws securing the Side input decorative plastic piece on the right.Remove the 4 screws securing the Main Board indicated below in red.

Remove the Right side decorative plastic piece by removing top and bottom screws.Remove the remaining 6 screws that remove the “Shield” covering the Main Board.Careful at this point, the Board willSwing free of the supports.


Main Board Connector P800 Voltage and Diode CheckMain Board Connector P800 Voltage and Diode Check


OL0V0Vn/c24

OL3.2V0Vn/c23

2.15V3.38V0VVBR-B22

OL1.68V0VBR121

2.15V3.29V0VINV-On/Off20

1.25V2.86V0VRL-ON19

OL4.57V5VAC-DET18

OL3.3V0VVBR-B 5V-MNT17

GndGndGndGnd15, 16

GndGndGndGnd13, 14

1.23V5.15V5VST-5V11, 12

1.23V5.15V5VST-5V9, 10

GndGndGndGnd7, 8

3.03V11.8V0V12V5, 6

GndGndGndGnd3, 4

OL16V0V16V1, 2


P800 Connector "Main" to P201 "SMPS Board"


Main Board Connector P902 LVDS Layout and 12V Circuit Main Board Connector P902 LVDS Layout and 12V Circuit

LVDS Signal Waveforms

Shown on back of Interconnect

Diagram

Panel Control from IC407 Pin 33Q900 turns on Q901 LVDS Switch generating LVDS 12VAll voltages are shown on the Interconnect Diagram

LVDS 12V

For LocationsSee Main BoardBack Side View


Main Board Connector P902 Even Pins Voltage and Diode CheckMain Board Connector P902 Even Pins Voltage and Diode Check


3V3.07V0.4VSize Sel25

Gndn/c0Vn/c23

OLn/c0Vn/c21

1.11V1.14V0VLVDS19

1.11V1.08V0VLVDS17

1.06V1.1V0VLVDS15

1.11V1.2V0VLVDS13

0.98V1.2V0VLVDS11

Gnd0V0VGnd9

Gnd0V0VGnd7

Gnd0V0VGnd5

OL12.3V0VLVDS 12V3

OL12.3V0VLVDS 12V1

Diode CheckRunSBYLabelPin

Gnd0V0VGnd26

OLn/c0Vn/c24

OLn/c0Vn/c22

1.06V1.06V0VLVDS20

1.06V1.13V0VLVDS18

1.05V1.09V0VLVDS16

1.06V1.05V0VLVDS14

0.98V1.1V0VLVDS12

Gnd0V0VGnd10

Gnd0V0VGnd8

Gnd0V0VGnd6

OL12.3V0VLVDS 12V4

OL12.3V0VLVDS 12V2


P902 Connector "Main" to CN1 “T-CON Board"




Gnd0V0VGnd15

0.8V0V2.1VLED-R14

0.8V2.1V0VLED-G13

Gnd0V0VGnd12

OL0V0Vn/c11

2.3V4.1V4.1VIR10

0.8V0V0VPWM-LED9

0.53V5V5VST-5V8

OL0V0Vn/c7

1.4V3.4V3.4VKEY-26

1.4V3.4V3.4VKEY-15

Gnd0V0VGnd4

Gnd0V0VGnd3

1.4V3.4V3.4VKEY42

1.4V3.4V3.4VKEY31


P401 Connector "Main Board" to "Front Keys"




Gnd0V0VGnd13

0.83V0V0Vn/c12

Gnd0V0VGnd11

OL0V0Vn/c10

Gnd0V0VGnd9

OL0.6V0VY8

OL0.8V0VPb7

OL0.8V0VPr6

GndGnd0VGnd5

OL3.3V3.34Vn/c4

OL3.3V3.34Vn/c3

1.60V* 3.3V*3.3VDisc Chedk2

OL3.34V3.34Vn/c1


OL0V0Vn/c26

Gnd0V0VGnd25

OL0V0Vn/c24

OL0V0Vn/c23

Gnd0V0VGnd22

OL0V0Vn/c21

OL2.4V0VDVD-R-In220

Gnd0V0VGnd19

OL2.4V0VDVD-L-In218

OL0V0VDVD-MUTE17

0.83V1.8V3.38VDVD-SPDIF16

OL0V0Vn/c15

OL0.7V0Vn/c14


P904 Connector "Main" to CN401 "DVD Player"

*Pin 2: 3.3V With Disc Player and 0V No Disc Player


Main Board Connectors P900, P901, P500 and P200 Voltage and DiodMain Board Connectors P900, P901, P500 and P200 Voltage and Diode Checke Check


Gnd0VGndGnd4

3V3.4V0.7VDVDP-TXD3

3V3.08V0.7VDVDP-RXD2

1.68V*3.4V*3.4VDisk-Enable1


P900 Connector "Main" to P402 "DVD Player"

0.45V5.010V5V6

Gnd0V0VGnd5

Gnd0V0VGnd4

.099V3.37V3.4VDVDP 3.3V3

Gnd0V0VGnd2

3V12.3V0V12V1


P901 Connector "Main" to CN400 "DVD Player"

2.78V8.15V0VL-4

2.78V8.15V0VL+3

2.78V8.14V0VR-2

2.78V8.14V0VR+1


P500 Connector "Main" to "Speakers"

Gnd0V0VGnd4

OL5V0VSDA3

OL5V0VSCL2

OL5V0VVcc1


P200 Connector "Main" Software Download

*Pin 1: 3.4V with No Disc and 0V with Disc inserted


MCN1

To BacklightRight Side

To BacklightLeft Side

Transformers

Ballast Start Det LED (LED1)

F18A/125V

p/n EAY56797501BALLAST SECTION (With Shield) LAYOUTBALLAST SECTION (With Shield) LAYOUT


Ballast Board Assembly LayoutBallast Board Assembly Layout

MCN1

Ballast Start DetLED LED1

To BacklightRight Side

To BacklightLeft Side

Transformers

F18A/125V


Ballast Transformer WaveformsBallast Transformer Waveforms

T1/T2 Pin 6

Transformers

��

T1/T2 Pin 1

34V p/p 64.89kHz22.2V p/p 220kHz

PrimarySide Warning,

secondary is over 1.2Kv


Ballast Control Signals from Main Board P800Ballast Control Signals from Main Board P800


Backlight Drive Backlight Drive Signal EffectsSignal Effects

PWMDIM manipulates

the Burst Triangle

Oscillator in the ballast drive IC.

ADIM also manipulates

the Burst Triangle

OscillatorBut it is not

used.

WaveformJust for

Explanation, taken from a

different chassis.


Ballast Removal (Heat Sink and Insulators)Ballast Removal (Heat Sink and Insulators)

Protects the Outputs

Insulator

InsulatorShiny Side

Down(Conductive)

Be sure to replace “All”

heat sink materials and

insulators.

Cut Out

AlignmentNotch

Alignment Notch

Heat Transfer MaterialShield

p/n EAY56797501


Ballast Connector MCN1 Voltage and Diode CheckBallast Connector MCN1 Voltage and Diode Check


GndGndGndGnd_214

OL3.40V0VVBR_B13

OL3.45V0VOn/Off12

OL1.67V0VBVR_A11

GndGndGndGnd_110

GndGndGndGnd9

GndGndGndGnd8

GndGndGndGnd7

GndGndGndGnd6

OL24.52V0VVBL5

OL24.52V0VVBL4

OL24.52V0VVBL3

OL24.52V0VVBL2

OL24.52V0VVBL1


MCN1 "Ballast" to P203 "SMPS"


TT--CON (TFT DRIVE) SECTIONCON (TFT DRIVE) SECTION

CN1 LVDS

To Main

Remove Screw

Remove Screw

Remove One Screw at the to of the Brace then Remove LVDS and three screws.

Remove Screw

TT--CON (TFT DRIVE) Board Removal)CON (TFT DRIVE) Board Removal)


TT--CON (TFT Drive) Board LayoutCON (TFT Drive) Board Layout

CN2 CN3

CN1 LVDS

US2

To Main

To TFT Panel To TFT Panel

Use the Connector P902 on Main Board for Voltages and Signal

Readings

3) 0.0V2) 1.8V1) 3.3V

US2

12VF1

6.3V/1.5A

Remember to put the three screws back in for ground purposes.

p/n EAT56801301


TT--CON (TFT Drive) Board DC to DC Converter Voltages for PanelCON (TFT Drive) Board DC to DC Converter Voltages for Panel

The voltages developed by US1 are used on the T-CON and for the X and Y drivers inside the TFT panel.

* The Voltages on CN2 and CN3 must be present for the panel to operate.

US1 Voltages

6.6V483.3V320V16

0V47.6V310V15

6.6V461.8V306.9V14

6.6V454.3V2915.0V13

6.6V44V0V284.8V12

15.0V4312.0V270V11

15.0V4212.0V261.2V10

1.2V4112.0V2521.0V9

0V403.3V2419.708

15.0V393.3V235.4V7

12.0V3811.3V223.3V6

12.0V371.2V211.9V5

0V360V200.7V4

0V350V192.4V3

0V344.3V186.6V2

6.0V331.2V176.6V1

DCPinDCPinDCPin

US1 Voltages


TT--CON Board Removal (LVDS Removal)CON Board Removal (LVDS Removal)

Disconnect CN1 LVDS CableCAUTION: When removing LVDS Cables, be careful. Press the release Tabs to avoid damage to Board or to the Cable itself.

LVDS ConnectorsPress in from the sides and lift out.

Press in Press in


TT--CON Board Connector CN1Voltage and Diode CheckCON Board Connector CN1Voltage and Diode Check


CN1 Connector "T-CON" Odd to P902 "Main"

Gnd0V0VGnd26OL3.07V0.4VSize Sel25

n/cn/c0Vn/c24n/cn/c0Vn/c23

n/cn/c0Vn/c22n/cn/c0Vn/c21

0.88V1.06V0VLVDS200.88V1.14V0VLVDS19

0.88V1.13V0VLVDS180.88V1.08V0VLVDS17

0.88V1.09V0VLVDS160.88V1.1V0VLVDS15



Gnd0V0VGnd10Gnd0V0VGnd9



2.9V12.3V0VLVDS 12V42.9V12.3V0VLVDS 12V3

2.9V12.3V0VLVDS 12V22.9V12.3V0VLVDS 12V1

Diode CheckRunSBYLabelPinDiode

CheckRunSBYLabelPin

Use P902 on the "Main" Board for making Voltage, Diode Mode and Waveform Checks

Outside Pins are Ground and not counted

Press Tabs to Release


DVD Connector InformationDVD Connector Information

The following section covers the Interconnection Voltages and The following section covers the Interconnection Voltages and Resistance checks between the DVD Player and the Main Resistance checks between the DVD Player and the Main Board.Board.


DVD Player Removal (1 of 2)DVD Player Removal (1 of 2)

Remove the 8 Screws Holding the DVD Player in place

RemoveTape


DVD Player Removal (2 of 2)DVD Player Removal (2 of 2)

Disconnect CN400, CN401 and CN402

This screw hidden by tape in previous photo (Step2).

CN402

CN403 Not Used

CN401

CN400


DVD Player RemovedDVD Player RemovedSet will work with DVD Player removed


DVD Connector CN401 Voltage and Diode CheckDVD Connector CN401 Voltage and Diode Check


Gnd0V0VGnd13

0.15V0V0Vnc12

Gnd0V0VGnd11

OL0V0Vnc10

OLGndGndGnd9

OL0.6V0VDVDP-Y8

OL0.8V0VDVDP-Pb7

OL0.8V0VDVDP-Pr6

GndGndGndGnd5

2.34V3.3V3.34Vnc4

3.13V3.3V3.34Vnc3

3.13V*3.4V*3.3VCheck2

3.13V3.34V3.34Vnc1


CN401 Connector "DVD" to P904 "Main"

OL0V0Vnc26

Gnd0V0VGnd25

OL0V0Vnc24

OL0V0Vnc23

Gnd0V0VGnd22

OL0V0Vnc21

1.1V2.4V0VDVDP-R20

Gnd0V0VGnd19

1.1V2.4V0VDVDP-L18

2.3V0V0VDVDP-MUTE17

OL1.8V3.38VSPDIF16

Gnd0V0Vnc15

0.15V0.7V0Vnc14


*Pin 2: 3.4V With Disc Player and 0V No Disc Player

NOTE: If the DVD Player fails, or if any Connector from the DVD Player is open, when selecting the DVD

player as the input, it will show “No Signal” error.


DVD Connector CN400 and CN402 Voltage and Diode CheckDVD Connector CN400 and CN402 Voltage and Diode Check


1.2V5V0VP5V6

GndGndGndGnd5

GndGndGndGnd4

0.78V3.37V3.4VP3.3V3

GndGndGndGnd2

3.22V12.3V0VP12V1



GndGndGndGnd4

OL3.4V0.7VRXD13

OL3.08V0.7VTXD12

OL*3.4V*3.4VGP1011



*Pin 1: 3.4V with No Disc and 0V with Disc inserted


FRONT IR BOARD SECTIONFRONT IR BOARD SECTION

The following section covers the Interconnection Voltages The following section covers the Interconnection Voltages and Diode Mode checks between the Front Board and the and Diode Mode checks between the Front Board and the Main Board and the Front Board and the Side Key Board.Main Board and the Front Board and the Side Key Board.


Front Board Assembly LayoutFront Board Assembly Layout

J2 J1To Main BoardTo Side Keys Board ZD3

3.4V Zener

ZD15V Zener

ZD24.1V Zener


Front Board Assembly Rear View LayoutFront Board Assembly Rear View Layout

POWERBUTTON

IR Receiver

POWER LED


Front Control Connectors J1 and J2 Voltage and Diode CheckFront Control Connectors J1 and J2 Voltage and Diode Check

With all Connectors Removed, Resistance taken in Diode Mode.

Gnd0V0VGnd15

3.2V0V2.1VLED-R14

3.2V2.1V0VLED-G13

Gnd0V0VGnd12

OL0V0Vn/c11

OL4.1V4.1VIR10

2.4V0V0VPWM-LED9

2.7V5V5VST-5V8

OL0V0Vn/c7

OL3.4V3.4VKEY-26

OL3.4V3.4VKEY-15

Gnd0V0VGnd4

Gnd0V0VGnd3

OL3.4V3.4VKEY42

OL3.4V3.4VKEY31


J1 "Front Board" to P401 "Main"

Gnd0V0VGnd8

OL3.41V3.41VKey 47

Gnd0V0VGnd6

OL3.41V3.41VKey 35

Gnd0V0VGnd4

OL3.41V3.41VKey 23

Gnd0V0VGnd2

OL3.4V3.4VKey 11


J2 "Front Board" to P101 "Side Key"


Side Control Key P101 Connector Layout, Voltage and Diode CheckSide Control Key P101 Connector Layout, Voltage and Diode Check

With all Connectors Removed, Resistance taken in Diode Mode.

Gnd0V0VGnd8

OL3.41V3.41VKey 47

Gnd0V0VGnd6

OL3.41V3.41VKey 35

Gnd0V0VGnd4

OL3.41V3.41VKey 23

Gnd0V0VGnd2

OL3.4V3.4VKey 11


P101 "Side Control" to J2 "Front Board"


INTERCONNECT DIAGRAM (11 X 17 FOLDOUT SECTION)INTERCONNECT DIAGRAM (11 X 17 FOLDOUT SECTION)

This section shows the 11X17 foldout thatThis section shows the 11X17 foldout that’’s available in the Paper s available in the Paper and Adobe version of the Training Manual.and Adobe version of the Training Manual.

The Adobe version of this Training Manual allows the viewer to The Adobe version of this Training Manual allows the viewer to zoom in and out making reading of the small text easier.zoom in and out making reading of the small text easier.This Power Point shows a graphical representation of the 11 X 17This Power Point shows a graphical representation of the 11 X 17foldout page so clarity is limited.foldout page so clarity is limited.

P401

LD800

MCN1

54 Meg

24 Mhz

Reset

Grayed Out ICs are located on Back

X400

X200

IC809

IC400

32LG40 INTERCONNECT DIAGRAM

P800

P901

P900

P904

J2 J1

Ballast PWB

Power SupplyMain (Digital) Board

T-CON Board

Front PWB Assembly(Interface)

Side

(Key

) Con

trol

s

P200

P500

A/C In

P203

P201

P202Not Used

SoftwareUpgrades

F101

F100

To Backlight

To Backlight

Right Side

Left Side

CN1

SC100

L

N

A/C Fuse5A / 250V

334V Actual Reading3.15A / 250V Rating

F124V

8A / 150V

IR ReceiverPower Button

To Speakers

P101

P902 Pin 11

P201 Even "SMPS" to P800 "Main PWB"Pin Label STBY Run Diode Check Pin Label STBY Run Diode Check1 16.5V 0V 16V 0.31V 2 16.5V 0V 16V 0.31V3 Gnd Gnd Gnd Gnd 4 Gnd Gnd Gnd Gnd5 12V 0V 11.8V 1.69V 6 12V 0V 11.8V 1.69V7 Gnd Gnd Gnd Gnd 8 Gnd Gnd Gnd 0V9 5.2V 5.15V 0.34V 10 5.2V 5.15V 5.15V 0.34V

11 5.2V 5.15V 0.34V 12 5.2V 5.15V 5.15V 0.34V13 Gnd Gnd Gnd Gnd 14 Gnd Gnd Gnd Gnd15 Gnd Gnd Gnd Gnd 16 Gnd Gnd Gnd Gnd17 ERR 0V 0V 1.26V 18 ACD 5.05V 4.57V OL19 PWR 0V 2.86V OL 20 INV-On/Off 0V 3.29V OL21 BR1 0.1V 1.68V OL 22 PWM-DIM 0V 3.38V OL23 N/C 0V 3.2V OL 24 N/C 0V 0V OL

P201 Odd "SMPS" to P800 "Main PWB"P203 "SMPS" to MCN1 "Ballast PWB"Pin Label STBY Run Diode Check1 24V 0V 24.52V 0.33V2 24V 0V 24.52V 0.33V3 24V 0V 24.52V 0.33V4 24V 0V 24.52V 0.33V5 24V 0V 24.52V 0.33V6 Gnd Gnd Gnd Gnd7 Gnd Gnd Gnd Gnd8 Gnd Gnd Gnd Gnd9 Gnd Gnd Gnd Gnd

10 Gnd Gnd Gnd Gnd11 BR1 1.67V OL12 INV On-Off 3.45V OL13 PWM-DIM 3.40V OL14 ERROR 0V OL

BSM

0V0V0V0V

5.15V5.15V

IC806

IC801

IC807

TUNER

IC803

IC00BCM

P902

IC80

8

Q901

IC401

IC805

Far left and right pins are not counted, they are ground.

F1 6.3V/1.5A

US2

12V

3) 0.0V2) 1.8V1) 3.3V

IC802

Q400IC405

Q900

IC801

LD1Ballast

Drive LED

Example Of LVDS Signal

IC201 IC405 IC806 Q801PIN FUNCTION NAME STBY RUN PIN FUNCTION NAME STBY RUN PIN FUNCTION NAME STBY RUN PIN FUNCTION NAME STBY RUN2 IN +5V 0V 5V 1 IN 3.3V_MICON 3.41V 3.41V 1 On/Off Control Power_CTL_3.3V 0V 3.4V 1,3 IN ST_5V 0V 5V3 On/Off Control BCM DDR Power 0V 3.4V 2 Gnd Gnd Gnd Gnd 2 IN +5V_SUB 0.36V 5V 2,4 On/Off Control Q802 0V 0.28V7 OUT USB_PWR_Out_1 0V 5V 3 OUT Reset (Lo-Hi) 0.6V 0.6V 3 Gnd Gnd Gnd Gnd 5,6,7,8 OUT +5V_SUB 0V 5V8 OUT +3.3V 0V 3.1V IC802 4 OUT D3.3V_BCM 0.1V 3.4V Q802

IC304 PIN FUNCTION NAME STBY RUN IC807 PIN FUNCTION NAME STBY RUNPIN FUNCTION NAME STBY RUN 1 Gnd +3.3V 0V 5V PIN FUNCTION NAME STBY RUN B On/Off Control RL_ON 0V 3.29V3,8 OUT DDRO_VTT 0V 1.29V 2 OUT Gnd Gnd Gnd 1 IN +9V 0V 8.9V C Pull Down ST_5V 0V 5V

5,6,7 IN D2.6V_BCM 0V 2.6V 3 IN +5V_SUB 0V 3.2V 2 On/Off Control Power_CTL_3.3V 0V 3.4V E Gnd Gnd Gnd Gnd4 On/Off Control DDRO_VTT 0V 1.29V IC803 3 OUT +5V 0V 5V Q400

IC400 PIN FUNCTION NAME STBY RUN 4 n/c n/c n/c n/c PIN FUNCTION NAME STBY RUNPIN FUNCTION NAME STBY RUN 1 IN +12V 0V 12V 5 Gnd Gnd Gnd Gnd B Reset Reset 0.6V 0.6V1 IN D3.3V_BCM 0V 3.4V 2 Gnd Gnd Gnd Gnd IC809 C Vcc 3.3VVST_MICON 0V 0V2 Gnd Gnd Gnd Gnd 3 OUT +9V 0V 9V PIN FUNCTION NAME STBY RUN E Gnd Gnd Gnd Gnd3 OUT Reset (Lo-Hi) 0V 3.39V 6,7,8,10 IN +5V_SUB 0.36V 4.98V

17 On/Off Control Power_CTL_2.6V 0V 3.41V1,2,3,4,5 OUT D2.6V_BCM 0V 2.66V

14,15 n/c n/c n/c n/c11,18,19,20 Gnd Gnd Gnd Gnd

5V Sub Switch

5V Sub Switch Controller for Q801

Reset Generator for MICRO IC407Reset Generator for IC401 3.3V BCM (On Back)

Reset Generator for Q400 Micro Reset

2.6V BCM+3.3V Regulator (3.3V TMDS_SW)

USB Power

+9V Regulator

D3.3V/A3.3V_BCM Regulator turns on LD800

D3.3V_BCM Regulator (Also A3.3V_BCM)

D2.6V_BCM Regulator (Also A2.6V_BCM)

IC401 IC808PIN FUNCTION NAME STBY RUN PIN FUNCTION NAME STBY RUN14 IN D3.3V_BCM 0V 3.41V 2 IN ST_5V 5V1 On/Off Control Reset from IC400 0V 3.4V 3 OUT 3.3VST_MICON 3.43V6 OUT BCM_RESET 0V 3.4V 4 Gnd Gnd Gnd Gnd

IC801 Q900PIN FUNCTION NAME STBY RUN PIN FUNCTION NAME STBY RUN1 Gnd Gnd Gnd Gnd B Control LVDS_PANEL_CTRL 0V 0.75V2 OUT +1.8V_NTP 0V 1.8V C Pull Down 12V LVDS Switch Control 0V 0V3 IN 3.3V_TMDS_SW 0.26V 3.29V E Gnd Gnd 0V 0V

IC805 Q901PIN FUNCTION NAME STBY RUN PIN FUNCTION NAME STBY RUN

6,7,8,10 IN +5V_SUB 0.38V 5V 1,3 IN 12V 0V 12.36V17 On/Off Control Power_CTL_1.2V 0V 3.41V 2,4 On/Off Control Q900 0V 6.16V

1,2,3,4,5 OUT D1.2V_BCM 0V 1.29V 5,6,7,8 OUT LVDS 12V 0V 12.36V13, 14,15,16 n/c n/c 0V 0V

11,12,18,19,20 Gnd Gnd Gnd Gnd

Screen Print for Pin No is incorrect, use IC

LVDS 12V Switch

Controller for LVDS 12V Switch Q901

BCM IC100 Reset

+1.8V_NTP Regulator

D1.2V/A1.2V BCM Regulator

ST-BY 3.3V DC-DC Converter

5V3.43V

REGULATORS/ICs ON BACKREGULATORS/ICs ON FRONT

CN2 CN3

TO TFT MODULE

To Force Power Supply On.Disconnect P800 on Main PWB.Jump 5V to pin 19.Ballast and All voltages should turn on.

DVD Drive

CN400

CN401

CN403

CN402

Not Used

IC407Micro

Waveforms for P902Pins 11 through 20

(All waveforms on back of 11X17 fold out)

1.5V1.5V

1.5V

16 16

On then Off after ballast

fires

22V p/p 34V p/p

Pin 1 Pin 6

T1 T2

Secondary over 1.2Kv

Do not run without heat sink attached

*PWM-DIM (PDIM) Pin 13 can vary according to OSD Backlight setting. 0.9V 0% to 3.3V 100%

*PWM-DIM (PDIM) Pin 22 can vary according to OSD Backlight setting. 0.9V 0% to 3.3V 100%

32LG40 LVDS P902 WAVEFORMS

32LG40 LVDS CABLE WAVEFORMS:Waveforms taken using SMTP Color Bar input.All readings give the Scale and Time Base related to scope settings. Top waveform in each image gives a slower rate.10mV at 5uS per division.Bottom waveform shows a blow up sample. 10mV at 2uS per division.

32LG4032LG40Direct View LCD

This concludes the 32LG40 training session.

32lg40 training manualdiagramas.diagramasde.com/otros/32lg40-presentation.pdf6 lcd dv august 2008...

Documents