310643w, displacement pumps, repair, english€¦ · equipment manuals. read fluid and solvent...
TRANSCRIPT
310643WEN
Repair
Displacement PumpUse only genuine Graco replacement parts. Use of non-Graco replacement parts may void warranty.
3300 psi (22.7 MPa, 227 bar) Maximum Working Pressure
Model 248204, Series AUltraMax II and Ultimate MX II 695/795ASM Zip-Spray 2700 Plus, 3100 PlusASM AllPro Mach 8600 Plus and 11000 PlusASM H2700 Plus
Model 255968, Series AASM 3600G Plus
Model 248205, Series AUltraMax II and Ultimate MX II 1095/1595
Model 249059, Series ATexSpray Mark V
Model 249057, Series ATexSpray Mark V
Model 277069, Series ALineLazer 3900, ES2000
Model 277070, Series A LineLazer 5900
Model 253056, Series AMark IV
Model 257146, Series AIronman 300E and Ironman 500G
Important Safety InstructionsRead all warnings and instructions in this manual. Be familiar with the controls and the proper usage of the equipment. Save these instructions.
ti2311
Warnings
2 310643W
Table of ContentsWarnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Parts - Pump 248204, 277069, 255968 . . . . . . . . . 14Parts - Pump 248205, 249057, 249059,
277070, 257146 . . . . . . . . . . . . . . . . . . . . . . . . 15
Parts - Pump 253056 . . . . . . . . . . . . . . . . . . . . . . . 16Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Graco Standard Warranty . . . . . . . . . . . . . . . . . . . . 1
WarningsThe following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When these symbols appear in the body of this manual or on warning labels, refer back to these Warnings. Product-specific hazard symbols and warnings not covered in this section may appear throughout the body of this manual where applicable.
WARNINGEQUIPMENT MISUSE HAZARDMisuse can cause death or serious injury.• Do not exceed the maximum working pressure or temperature rating of the lowest rated system
component. See Technical Data in all equipment manuals.• Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all
equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete information about your material, request MSDS from distributor or retailer.
• Turn off all equipment and follow the Pressure Relief Procedure when equipment is not in use.• Check equipment daily. Repair or replace worn or damaged parts immediately with genuine manu-
facturer’s replacement parts only.• Do not alter or modify equipment. Alterations or modifications may void agency approvals and create
safety hazards.• Use equipment only for its intended purpose. Call your distributor for information.• Do not use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or flu-
ids containing such solvents.• Comply with all applicable safety regulations.
MOVING PARTS HAZARDMoving parts can pinch, cut or amputate fingers and other body parts.• Keep clear of moving parts.• Do not operate equipment with protective guards or covers removed.• Pressurized equipment can start without warning. Before checking, moving, or servicing equipment,
follow the Pressure Relief Procedure and disconnect all power sources.
SKIN INJECTION HAZARDHigh-pressure spray is able to inject toxins into the body and cause serious bodily injury. In the event that injection occurs, get immediate surgical treatment.• Do not aim the gun at, or spray any person or animal.• Keep hands and other body parts away from the discharge. For example, do not try to stop leaks with
any part of the body.• Always use the nozzle tip guard. Do not spray without nozzle tip guard in place.• Do not leave the unit energized or under pressure while unattended. When the unit is not in use, turn
off the unit and follow the Pressure Relief Procedure for turning off the unit.• Always engage the trigger lock when not spraying. Verify the trigger lock is functioning properly.
Service
310643W 3
Service
Pressure Relief ProcedureFollow the Pressure Relief Procedure whenever you see this symbol.
1. Engage trigger lock.
2. Turn ON/OFF switch to OFF.
3. Unplug power cord.
4. Disengage trigger lock. Hold metal part of gun against grounded metal pail and trigger gun into pail to relieve pressure.
5. Engage the trigger lock.
6. Open all fluid drain valves in the system, having a waste container ready to catch drainage. Leave drain valve(s) open until you are ready to spray again.
7. If you suspect the spray tip or hose is clogged or that pressure has not been fully relieved after follow-ing the steps above, VERY SLOWLY loosen tip guard retaining nut or hose end coupling to relieve pressure gradually, then loosen completely. Clear hose or tip obstruction.
Pump Repair Kits
Tools Needed• Vise
• 12 in. adjustable, open-end wrench (2)
• Hammer (20 oz maximum)
• Small screwdriver
• Throat Seal Liquid
• Pick or long small screwdriver
Cleaning and Inspecting PartsClean and inspect parts. Pay particular attention to the ball seats in the intake valve and piston, which must have no nicks or wear, and to the inside of the sleeve and the outside of the piston rod, which must not be worn or scratched. Replace worn or damaged parts.
NOTE: Remove and clean sleeve when repacking pump.
This equipment stays pressurized until pressure is manually relieved. To help prevent serious injury from pressurized fluid, such as skin injection, splashing fluid and moving parts, follow the Pressure Relief Procedure when you stop spraying and before cleaning, checking, or servicing the equipment.
Pump Repair Kit
248204, 255968 248212253056 287825248205, 249057, 249059, 257146
248213
COMPONENT RUPTURE HAZARDTo reduce the risk of serious injury from pressurized fluid, never use sharp or pointed tools to remove sleeve. If the sleeve cannot be removed easily, return the sleeve and cylinder to a Graco distributor for removal.
Service
4 310643W
Repair When Pump is Separated From Sprayer
Disassembling the Pump
1. Remove packing nut (202) and o-ring (228).
2. Unscrew intake valve from cylinder.
3. Disassemble intake valve. Clean and inspect o-ring (227). NOTE: A pick may be required to remove o-ring.
4. Tap piston rod out of cylinder with a hammer or flip over and tap piston rod out against a bench.
5. Remove piston rod from sleeve, or remove sleeve from cylinder. Mark IV models: Remove sleeve spacer (230) from sleeve.
ti7566a
228
202
ti7569a
ti7570e
211
215
214
212
213
227
ti23115a
NOTE: Sleeve may come out of cylinder with piston rod.
ti7571a
ti7572a
Service
310643W 5
6. Unscrew piston valve from piston rod. Clean and inspect parts. The piston has a special thread lock-ing/sealing patch. Do not remove the patch. The patch allows four disassembly/assembly procedures before it is necessary to apply thread sealant to the threads.
7. Remove packings and glands from piston rod.
8. Remove throat packings and glands from cylinder. Discard throat packings and glands.
Assembling the Pump1. Soak all leather packings in SAE 30W oil for 1 hour
minimum prior to assembly. Stack male gland (204) on piston rod. Alternately stack UHMWPE (208) and leather (218) packings (note orientation) on piston rod. Install female gland (217). Install piston wiper (216) (note orientation) and backup washer (229) on piston valve (210). Threads are good for four repackings. Use thread sealant on piston valve threads after four repackings.
COMPONENT RUPTURE HAZARDTo reduce the risk of serious injury from pressurized fluid, do not clean or wipe the piston valve threads. Cleaning the piston valve threads could destroy the special sealing patch and cause the piston valve to come loose during operation.
ti7576a
ti3940b
Not used on248204,253056,255968
ti7573b
Not used on248204,253056,255968
216
218 208204217
210
229
ti7574d
Not used on248204,253056,255968
Service
6 310643W
2. Install ball (206) in piston rod. If thread sealant is applied to piston valve threads, make sure that none gets on ball.
3. Tighten piston valve to piston rod as specified:
4. Soak all leather packings in SAE 30W oil for one hour minimum prior to assembly. Place male gland (204) in cylinder. Alternately stack UHMWPE (203) and leather packings (223) (note orientation). Place female gland (224) in top of cylinder seat packings.
5. Install seal (201) into packing nut (202). Install o-ring (228) onto packing nut. Loosely install pack-ing nut into cylinder.
6. Grease piston packings.
Models Torque248204, 253056, 255968, 244069
27 +/-3 ft-lb.(36.1 +/-4.1 N•m)
248205, 249057, 249059, 277070, 257146
55 +/-3 ft-lb.(74.6 +/-4.1 N•m)
ti7575a
206
ti7576a
NOTICEDo not slide piston assembly into top of sleeve as this may damage piston packing.
ti7573f
203
224
223
204
Notused on248204,253056,255968
ti7581a
201
202
228
ti7578c
Service
310643W 7
7. Slide piston assembly into bottom of sleeve.
8. Grease top inch or two of piston rod that will go through the cylinder throat packings.
9. Grease o-rings (221) and place on sleeve. Slide sleeve/piston rod assembly into bottom of cylinder. Replace o-ring (207) if desired.
NOTE: O-ring (207) is not required for safe pump operation.
10. Mark IV models: Install o-ring (231) on sleeve spacer (230) and install sleeve spacer on sleeve.
11. Reassemble intake valve with new o-ring (227), seat (212) and ball (214). Seat may be flipped over and used on other side. Clean seat thoroughly.
ti7577a
ti7579a
221
207
ti7582a
ti7340a
231
230
ti7340b
215
214
212
213
227
ti23115a
Service
8 310643W
12. Install intake valve on cylinder. If a wrench is used torque as follows:
13. Torque packing nut (202) down onto adjustment spacer (228) 100 +/- 10 in-lb. (11.3 +/- 1.1 N•m)
14. Remove o-ring (228) when pump packings begin to leak after extended use. Then tighten packing nut down until leakage stops or lessens. This allows approximately 100 gallons of additional operation before a repacking is required.
Models Torque248204, 253056, 255968, 277069
67 +/- 5 ft-lb (90.8 +/-6.8 N•m)
248205, 249057, 249059, 277070, 257146
80 +/- 5 ft-lb (108.5 +/-6.8 N•m)
ti7569ati7568a
202
228
Service
310643W 9
Repair When Pump is On Sprayer
1. Perform Pressure Relief Procedure, page 3.
2. Remove intake valve.
3. Push up retaining spring (26).
4. Push out pin (29).
5. Disassemble intake valve. Clean and inspect. O-ring (227) may require a pick for removal.
6. Remove piston rod and sleeve.
ti4258c
ti4258a26
29
26ti4258bti4258b
215
214
212
213
227
ti23115a
ti7746a
Service
10 310643W
7. Invert piston rod and sleeve and pound on hard sur-face until piston rod comes out of sleeve. Mark IV models: Remove sleeve spacer from sleeve.
8. Remove packing nut (202).
9. Invert piston rod and insert into cylinder to force out throat packings.
10. Insert piston rod into cylinder with pin hole up and piston valve down. Insert pin into piston rod and crank shaft.
11. Remove piston valve from piston rod with a wrench.
12. Remove pin and piston rod from cylinder.
13. Soak all leather packings in SAE 30W oil for 1 hour minimum prior to assembly. Stack male gland (204). Alternately stack UHMWPE (203) and leather (223) packings (note orientation). Install female gland (224). Install seal (201) and packing nut (202) and o-ring (228).
ti7572a
202
ti7726a
ti4258e
ti4258f
ti4258g
ti4258g
ti4258h
201
228203
224
223
204
202
ti7573c
Not used on248204,253056,255968
Service
310643W 11
14. Remove packings and glands from piston rod.
15. Soak all leather packings in SAE 30W oil for one hour minimum prior to assembly. Stack male gland (219) on piston rod. Alternately stack UHMWPE (208)and leather (218) packings (note orientation) on piston rod. Install female gland (217). Install piston wiper (216) and backup washer (229) (note orientation) on piston valve (210). The special sealing patch on pis-ton valve threads is good for four repackings. Use thread sealant on piston valve threads after four repackings.
16. Install ball (206) in piston rod. NOTE: If thread seal-ant is applied to piston valve threads, make sure none gets on ball. Install piston valve on piston rod. Torque as follows:
17. Grease piston packings.
ti3939a
Not used on248204,253056,255968
210218
206
208
219217
229
216
ti3941a
Not used on248204,253056,255968
Models Torque248204, 253056, 255968, 277069 27 +/- 3 ft-lb (36.6 +/-4.1 N•m)
248205, 249057, 249059, 277070, 257146
55 +/- 3 ft-lb (74.6 +/-4.1 N•m)
ti7575b
206
ti7575b
ti7578c
Service
12 310643W
18. Slide piston assembly into bottom of sleeve. Make sure V-packing and u-cup are not rolled over or damaged. Mark IV models: Install o-ring (231) on sleeve spacer (230). Install sleeve spacer on sleeve.
19. Grease top inch or two of piston rod that will go through the cylinder throat packings.
20. Grease o-ring (221) and place on sleeve. Slide sleeve/piston rod assembly into bottom of cylinder. Replace o-ring (207) if desired. NOTE: O-ring (207) is not required for safe pump operation.
21. Torque seal and packing nut (202) down onto throat adjustment spacer (228) to 100 +/- 10 in-lb (11.3 +/- 1.1 N•m).
Remove o-ring when pump packings begin to leak after extended use. Then tighten packing nut down until leakage stops or reduces. This allows approxi-mately 100 gallons of additional operation before a repacking is required.
22. Push up retaining spring (26) with screwdriver.
23. Push in pin (29). NOTE: Make sure retaining ring falls into slot.
NOTICEDo not slide piston assembly into top of sleeve as this may damage piston packing.
ti7341a
Mark IV
ti7579a
ti4258j
207
221
ti7726b
202
228
ti4258k26
ti4258m
29
26
Service
310643W 13
24. Reassemble intake valve with new o-rings (227) and (230), seat (212) and ball (214). Seat may be flipped over and used on other side. Clean seat thoroughly.
25. Install intake valve on cylinder. Torque as follows:
Pump Packings
Models Torque248204, 253056, 255968, 277069 70 +/- 5 ft-lb (94.9 +/-6.8 N•m)
248205, 249057, 249059, 277070, 257146
80 +/- 5 ft-lb (108.5 +/-6.8 N•m)
215
214
212
213
227
ti23115a
ti4258n
ti7683d
223203
218 208
217
213214
204
221
224
205
219
215
212
227
222
202
221
216
206
210
Leather
Leather
201
220
228
207
229
230
V-Max™
UHWMPE,blue
V-Max™
UHWMPE,blue
Pump 248204
Parts - Pump 248204, 277069, 255968
14 310643W
Parts - Pump 248204, 277069, 255968Series ARef. Part Description Qty.201 179810 SEAL, throat 1202 193046 NUT, packing 1203* 192692 V-PACKING, throat, V-Max,
UHMWPE, blue3
204* 15C987 GLAND, male, throat, 1205 CYLINDER, pump
243346 Model 248204, 255968 1243346 Model 16X428 1
206* 105444 BALL, sst, 0.3125 in. 1207* 114054 PACKING, o-ring 1208* 192693 V-PACKING, piston, V-MAX,
UHMWPE, blue3
210 239932 VALVE, piston 1212† 239922 KIT, seat, carbide (includes 214 and
227)1
213 VALVE, intake (foot) 115C785 Model 248204, 255968195892 Model 277069
214*† 105445* BALL, sst. 0.5000 in. 1215 192624 GUIDE, ball 1216* 118503 WIPER, piston 1217* 178969 GLAND, female, piston 1218* 178939 V-PACKING, leather, piston 2219* 196880 GLAND, male 1220 248209 SLEEVE, cylinder 1221* 108526 O-RING, ptfe 2222 248206 ROD, piston 1223* 178940 V-PACKING, leather, throat 2224* 15C988 GLAND, female227*† 107079 PACKING, o-ring 1228 192714 SPACER, throat, nut 1229* 15C997 WASHER, backup 1230* 118494 O-RING, fluoroelastomer
(not used on Lo-Boy)1
* These parts are also included in Repair Kit 248212, which may be purchased separately.
† These parts are also included in Carbide Seat Kit 239922, which may be purchased separately.
223
216
201
202
224
203
204
205
221
220
222
206
219
218
217
210
215
212
213
214
208
221
207 227
228
229
230(Not an O-ring groove)
ti4255a
Parts - Pump 248205, 249057, 249059, 277070, 257146
310643W 15
Parts - Pump 248205, 249057, 249059, 277070, 257146Series ARef. Part Description Qty.201 183171 PLUG 1202 193032 NUT, packing 1203* 193124 V-PACKING, throat, V-Max,
UHMWPE, blue4
204* 15C989 GLAND, packing, male, throat 1205 CYLINDER, pump 1
243347 Model 248205, 277070196754 Model 249057, 249059, 257146
206 BALL, 0.375 in. 1101947* Model 248205, 249057, 277070, 257146116327 Model 249059, ceramic
207* 156633 PACKING, o-ring 1208* 193125 V-PACKING, piston, V-MAX,
UHMWPE, blue4
210 240150 VALVE, piston 1212 KIT, seat, carbide (includes 214, 227) 1
244199 Model 248205, 249057, 277070, 257146244571 Model 249059
213 HOUSING, intake (foot) 115C783 Model 248205196753 Model 249059, 249057195894 Model 277070, 257146
214 BALL 1102972*† Model 248205, 249057, 277070, 257146,
0.875 in.111453 Model 249059, ceramic, 0.750 in. 1
215 GUIDE, ball 1196967 Model 249059, 249057193027 Model 248205, 277070, 257146 1
216* 118504 WIPER, piston 1217* 183185 GLAND, female, piston 1218* 15E329 V-PACKING, leather, piston 3219* 183178 GLAND, packing, male 1220 SLEEVE, cylinder 1
248210 Model 248205, 249057, 249059, 277070257031 Model 257146
221* 107098 PACKING, o-ring 2222 ROD, piston
248207 Model 248205, 277070 1249028 Model 249059, 249057, 257146 1
223* 183175 V-PACKING, leather, throat 3224* 15C990 GLAND, female, throat 1227*† 108526 PACKING, o-ring 1228 C20987 SPACER, nut 1229* 15C998 WASHER, backup 1230* 118494 O-RING, fluoroelastomer (not used on
249057, 249059, 257146)1
231 117608 NIPPLE, straight 1Model 249057, 249059 (not shown)
232 162485 ADAPTER, 3/8 npt x 3/8 npsm 1Model 249057, 249059, 257146 (not shown)
1
* These parts are also included in Repair Kit 248213, which may be purchased separately.† These parts are also included in Carbide Seat Kit 244199, which may be purchased separately. These parts are also included in Pump Repair Kit 249189, which may be purchased separately.
ti23114a
222
205
207
221
220
204
203223
208
224
202
201
222
221
218
217
206
210
229
214
215
212
228
216
227
230
213
219
(Not an O-ring groove)
231
232
Parts - Pump 253056
16 310643W
Parts - Pump 253056Ref. Part Description Qty.201* 179810 SEAL, throat 1202 193046 NUT, packing 1203* 192692 V-PACKING, throat, V-Max,
UHMWPE, blue3
204* 15C987 GLAND, male, throat 1205 287876 CYLINDER, pump 1206* BALL, check 1
105444* BALL, sst, 0.3125 in. (optional)119259 BALL, ceramic, 0.3125 in. (standard)
207* 156593 PACKING, o-ring 1208* 192693 V-PACKING, piston, V-MAX,
UHMWPE, blue3
210 287877 VALVE, piston 1212† ^ SEAT, carbide, (not sold separately) 1213 287878 HOUSING, intake 1214 BALL, check, inlet 1
102972*† BALL, sst, 0.875 in. (optional)111453 ^ BALL, ceramic, 0.750 (standard)
215 196967 GUIDE, ball 1216* 118503 WIPER, piston 1217* 178969 GLAND, female, piston 1218 178939 V-PACKING, leather, piston 2219* 196880 GLAND, male 1220 248209 SLEEVE, cylinder 1221* 108526 O-RING, ptfe 2222 249969 ROD, piston (Mark IV) 1223* 178940 V-PACKING, leather, throat 2224* 15C988 GLAND, female227*† ^ 108526 PACKING, o-ring 1228* 158776 SPACER, throat, nut 1229* 15C997 WASHER, backup 1230 15G494 SPACER, sleeve 1231* 107098 O-RING 1
* These parts are also included in Repair Kit with stainless steel ball,287825, which may be purchased separately. These parts are also included in Repair Kit with ceramic ball, 24V063, which may be purchased separately. † These parts are also included in Carbide Seat Kit with stainless steel ball, 244199, which may be purchased separately.^ These parts are also included in Carbide Seat Kit with ceramic ball, 24V071, which may be purchased separately.
223
216
201
202
224
203
204
205
221
220
222
206
219
218
217
210
215
212
213
214
208
221
207
227
228
229
230
231
(Not an O-ring groove)
Technical Data
310643W 17
Technical DataU.S. Metric
Maximum Working Pressure 3300 psi 227 bar, 22.7 MPaFluid Inlet Size 1-5/16-12 un(m) 1-5/16-12 un(m)Fluid Outlet Size
248204, 255968, 277069 1/4 npt(f)248205, 249057, 249059, 253056, 277070, 257146 3/8 npt(f)
Wetted Parts stainless steel, PTFE, leather, nylon, zinc-plated carbon steel, tungsten carbide, chrome plating, fluoroelastomer, acetal, polyethylene
All written and visual data contained in this document reflects the latest product information available at the time of publication. Graco reserves the right to make changes at any time without notice.
Original instructions. This manual contains English. MM 310643
Graco Headquarters: MinneapolisInternational Offices: Belgium, China, Japan, Korea
GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA
Copyright 2014, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.www.graco.com
Revised W, May 2019
Graco Standard WarrantyGraco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERSThe Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite de ou en rapport, directement ou indirectement, avec les procédures concernées.
Graco InformationFor the latest information about Graco products, visit www.graco.com.
For patent information, see www.graco.com/patents.
TO PLACE AN ORDER, contact your Graco distributor or call 1-800-690-2894 to identify the nearest distributor.