303007-echolife hg865 gpon terminal service manual
DESCRIPTION
usage manualTRANSCRIPT
EchoLife HG865 GPON Terminal HG865 V100R001
Service Manual Issue 02
Date 2008-10-17
Part Number 303007
Copyright © Huawei Technologies Co., Ltd.
Huawei Proprietary and Confidential
Huawei Technologies Co., Ltd. provides customers with comprehensive technical support and service. For any assistance, please contact our local office or company headquarters.
Huawei Technologies Co., Ltd.
Address: Huawei Industrial Base Bantian, Longgang Shenzhen 518129 People's Republic of China
Website: http://www.huawei.com
Email: [email protected]
Copyright © Huawei Technologies Co., Ltd. 2008. All rights reserved. No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd.
Trademarks and Permissions
and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd. All other trademarks and trade names mentioned in this document are the property of their respective holders.
Notice The information in this document is subject to change without notice. Every effort has been made in the preparation of this document to ensure accuracy of the contents, but all statements, information, and recommendations in this document do not constitute the warranty of any kind, express or implied.
Copyright © Huawei Technologies Co., Ltd.
Huawei Proprietary and Confidential
EchoLife HG865 Service Manual Contents
Issue 02 (2008-10-17) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
i
Contents
About This Document ............................................................................................... 1 Safety Precautions ...................................................................................................... 5 1 Getting to Know the HG865 ............................................................................... 1-1
1.1 Product Overview........................................................................................................ 1-1 1.2 Front Panel and Rear Panel ......................................................................................... 1-3
1.2.1 Front Panel ...................................................................................................... 1-3 1.2.2 Rear Panel ....................................................................................................... 1-4
2 Installation Guide................................................................................................. 2-1 2.1 Installing the HG865 ................................................................................................... 2-1
2.1.1 Installing the HG865 Against the Wall ........................................................... 2-1 2.1.2 Installing the HG865 on a Platform................................................................. 2-1
2.2 Cable Connection ........................................................................................................ 2-2 2.3 Software Loading ........................................................................................................ 2-3
2.3.1 Setting Up Configuration Environment........................................................... 2-3 2.3.2 Configuring the File Transfer Server .............................................................. 2-4 2.3.3 Loading Files Through FTP ............................................................................ 2-4
3 Configuration Guide............................................................................................ 3-1 3.1 Service Description ..................................................................................................... 3-1 3.2 Basic Command .......................................................................................................... 3-1
3.2.1 Command Structure ........................................................................................ 3-1 3.2.2 Command Modes ............................................................................................ 3-2 3.2.3 Online Help of Command Line ....................................................................... 3-2 3.2.4 Common Commands....................................................................................... 3-3
3.3 SIP Service Configuration........................................................................................... 3-4 3.3.1 SIP Networking Method ................................................................................. 3-4 3.3.2 SIP Configuring Commands ........................................................................... 3-4 3.3.3 Configuring SIP Data...................................................................................... 3-5
3.4 MGCP Service Configuration ................................................................................... 3-10 3.4.1 MGCP Networking Method .......................................................................... 3-10 3.4.2 MGCP Configuration Commands ................................................................. 3-10 3.4.3 Configuring MGCP Data .............................................................................. 3-11
Contents EchoLife HG865
Service Manual
ii Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
Issue 02 (2008-10-17)
4 Operation Guide ................................................................................................... 4-1 4.1 Using a Telephone....................................................................................................... 4-1 4.2 Using an IP STB.......................................................................................................... 4-1 4.3 Using a PC .................................................................................................................. 4-2 4.4 Using a TV or a Digital STB....................................................................................... 4-2
5 Troubleshooting.................................................................................................... 5-1 6 Technical Specifications...................................................................................... 6-1 A SIP Service Configuration.................................................................................A-1
A.1 Voice Service Configuration................................................................................... A-1 A.1.1 Configuring IP Address ................................................................................. A-1 A.1.2 Configuring SIP Server.................................................................................. A-1 A.1.3 Configuring SIP User Information................................................................. A-2 A.1.4 Querying Configuration Result ...................................................................... A-2 A.1.5 Saving Configuration Data............................................................................. A-3
A.2 Data Service Configuration..................................................................................... A-3 A.2.1 Online Service................................................................................................ A-3 A.2.2 Fax Service .................................................................................................... A-4
B MGCP Service Configuration........................................................................... B-1 B.1 Voice Service Configuration....................................................................................B-1
B.1.1 Configuring IP Address...................................................................................B-1 B.1.2 Configuring Domain Name of the HG865 ......................................................B-1 B.1.3 Configuring IP address of MGC .....................................................................B-1 B.1.4 Configuring System Time ...............................................................................B-2 B.1.5 Starting DNS Client ........................................................................................B-2 B.1.6 Adding HG865 Network Management System...............................................B-3 B.1.7 Saving Configuration Data..............................................................................B-3
B.2 Data Service Configuration......................................................................................B-3 B.2.1 Online Service.................................................................................................B-3 B.2.2 Fax Service......................................................................................................B-5
C Acronyms and Abbreviations........................................................................... C-1
EchoLife HG865 Service Manual About This Document
Issue 02 (2008-10-17) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd. 1
About This Document
Purpose The EchoLife HG865 (hereinafter referred to as HG865) is an optical network terminal (ONT). It is designed for family users and Small Office Home Office (SOHO) users.
This document describes the appearance, functions, and technical specifications of the HG865. Also, this document provides guides for installing, configuring and using the HG865.
Related Versions Table 1-1 lists the product versions related to this document.
Table 1-1 Related Versions
Product Name Version
EchoLife HG865 V100R001
Intended Audience This document is intended for:
Technical support engineers Maintenance engineers
Organization This document consists of six chapters and is organized as follows.
Chapter Description
1 Getting to Know the HG865
This chapter describes the functions, the features, the front panel, and the rear panel of the HG865.
2 Installation Guide This chapter describes how to install the HG865, how to connect the HG865 to other devices, and how to load software applications.
About This Document EchoLife HG865
Service Manual
2 Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd. Issue 02 (2008-10-17)
Chapter Description
3 Configuration Guide This chapter describes the command lines of the HG865 and the configuration method of the SIP service of the HG865.
4 Operation Guide This chapter describes the operations of the HG865 after it is connected to a telephone, an IP STB, or a PC.
5 Troubleshooting This chapter describes the common faults of the HG865 and the solutions.
6 Technical Specifications
This chapter describes the interface parameters and physical specifications of the HG865.
Appendix A SIP Service Configuration
Appendix A describes configuration methods and procedures of the voice service and the data service of SIP.
Appendix B MGCP Service Configuration
Appendix B describes configuration methods and procedures of the voice service and the data service of MGCP
Appendix C Acronyms and Abbreviations
Appendix B lists the acronyms and abbreviations used in this document.
Conventions
Symbol Conventions The symbols that may be found in this document are defined as follows.
Symbol Description
Indicates a hazard with a high level of risk that, if not avoided, will result in death or serious injury.
Indicates a hazard with a medium or low level of risk which, if not avoided, could result in minor or moderate injury.
Indicates a potentially hazardous situation that, if not avoided, could cause equipment damage, data loss, and performance degradation, or unexpected results.
Indicates a tip that may help you solve a problem or save time.
Provides additional information to emphasize or supplement important points of the main text.
EchoLife HG865 Service Manual About This Document
Issue 02 (2008-10-17) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd. 3
General Conventions Convention Description
Times New Roman Normal paragraphs are in Times New Roman.
Boldface Names of files, directories, folders, and users are in boldface. For example, log in as user root.
Italic Book titles are in italics. Courier New Terminal display is in Courier New.
Command Conventions Convention Description
Boldface The keywords of a command line are in boldface.
Italic Command arguments are in italics.
[ ] Items (keywords or arguments) in square brackets [ ] are optional.
{ x | y | ... } Alternative items are grouped in braces and separated by vertical bars. One is selected.
[ x | y | ... ] Optional alternative items are grouped in square brackets and separated by vertical bars. One or none is selected.
{ x | y | ... } * Alternative items are grouped in braces and separated by vertical bars. A minimum of one or a maximum of all can be selected.
GUI Conventions Convention Description
Boldface Buttons, menus, parameters, tabs, windows, and dialog titles are in boldface. For example, click OK.
> Multi-level menus are in boldface and separated by the ">" signs. For example, choose File > Create > Folder.
About This Document EchoLife HG865
Service Manual
4 Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd. Issue 02 (2008-10-17)
Keyboard Operation Format Description
Key Press the key. For example, press Enter and press Tab.
Key 1+Key 2 Press the keys concurrently. For example, pressing Ctrl+Alt+A means the three keys should be pressed concurrently.
Key 1, Key 2 Press the keys in turn. For example, pressing Alt, A means the two keys should be pressed in turn.
Mouse Operation Action Description
Click Select and release the primary mouse button without moving the pointer.
Double-click Press the primary mouse button twice continuously and quickly without moving the pointer.
Drag Press and hold the primary mouse button and move the pointer to a certain position.
EchoLife HG865 Service Manual Safety Precautions
Issue 02 (2008-10-17) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd. 5
Safety Precautions
General Requirements: Before you install and use the HG865, read these safety precautions carefully. During storage, transportation, and operation of the device, keep the device dry. During storage, transportation, and operation of the device, avoid collision and
crash of the device. Never attempt to dismantle the device by yourself. If any fault is found, contact the
appointed maintenance center. Without prior written consent, no organization or individual is permitted to make
any change to the structure or safety design of the device. Huawei Technologies Co., Ltd. is not liable to any consequences or legal issues due to such changes.
While operating the device, observe all applicable laws and regulations, and respect the legal rights of others.
Environment Requirements: Place the device at a well-ventilated place. Do not place the device in direct
sunlight. Keep the device clean and free of dust. Keep at least 10 cm between the device and the closest object for heat dissipation. Do not place any object on top of the device. Otherwise, the device may get heated
during operation. It may even get damaged by the heavy load. Do not place the device on or near any object that can easily catch fire, such as
foam. Keep the device away from any heat source or bare fire, such as an electric heater
or a candle flame. Keep the device away from any electrical appliances with strong electromagnetic
field, such as a microwave oven, a refrigerator or a mobile phone.
Operation Requirement: Do no let a child operate the device without guidance. Do not let a child play with the device or any accessory. Swallowing the
accessories may lead to peril. Use the accessories provided or suggested by the manufacturer only. The power supply of the device must meet the requirements of the input voltage of
the device. Before plugging or unplugging a cable, shut down the device and disconnect it
from the power supply.
Safety Precautions EchoLife HG865
Service Manual
6 Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd. Issue 02 (2008-10-17)
When plugging or unplugging a cable, make sure that your hands are completely dry.
Do not tread on, pull or over-bend a cable to avoid malfunction of the device. Do not use old or damaged power cables. Do not stare at the optical interface on the device. Otherwise, your eyes may be
injured. Stop using the device when there is abnormal noise, smell or smoke emitted from
the device. Power off the device and unplug the power plug immediately, and then contact the appointed maintenance center.
Prevent any object (such as metal shavings) from entering the device through the heat dissipation intakes.
Do not scratch or abrade the shell of the device. Because the shed paint fragments may cause malfunction (such as short circuit) of the device by dropping into the device. They may also cause skin allergy.
Cleaning Requirements: Stop using the device and power off it before cleaning. Use a soft cloth to clean the device. Keep the power plug clean and dry. Using a dirty or wet power plug may cause
electric shock or other hazards.
EchoLife HG865 Service Manual 1 Getting to Know the HG865
Issue 02 (2008-10-17) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
1-1
1 Getting to Know the HG865
1.1 Pr
)
Interface (OMCI) software to facilitate configuration, maintenance and management of the remote services.
oduct Overview The HG865 is an optical network terminal (ONT) designed for family users and Small Office Home Office (SOHO) users. Using the gigabit-capable passive optical network (GPON) technology, the HG865 provides a high-speed data channel with the upstream rate up to 1.244 Gbit/s and downstream rate up to 2.488 Gbit/s through an optical fiber. The HG865 enables users to access the Internet to enjoy high-speed data services and high-quality voice and video broadband services, such as Internet Protocol TV (IPTVand Cable TV (CATV). The HG865 provides abundant hardware interfaces to meet diversified networking requirements of home users and SOHO users.
Provides one 10/100/1000 BASE-T Ethernet interface and three 10/100 BASE-T Ethernet interfaces for service terminals, such as PCs, STBs, and videophones.
Provides two Voice over IP (VoIP) telephone interfaces for high-quality and low-cost VoIP and Fax over IP (FoIP) services based on the IP network.
Provides one CATV interface for high-quality CATV transport services based on the CATV network.
The HG865 supports remote Telnet management, remote File Transfer Protocol (FTP) loading update, and automatic update of the online ONT Management and Control
1 Getting to Know the HG865 EchoLife HG865
Service Manual
1-2 Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
Issue 02 (2008-10-17)
Figure 1-1 shows the networking diagram of the HG865.
Figure 1-1 Networking diagram of the HG865
7
11
16
10
9
14
1
2
6
3
5
1312 15
84
1 Network management system 2 Internet
3 IPTV 4 Public Switched Telephone Network (PSTN)
5 Trunk gateway 6 IP network 7 Softswitch 8 VoIP 9 Switch 10 Optical Line Terminal (OLT) 11 HG865 12 Telephone 13 Fax machine 14 PC 15 TV 16 IP set-top box (STB)
EchoLife HG865 Service Manual 1 Getting to Know the HG865
Issue 02 (2008-10-17) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
1-3
1.2 Front Panel and Rear Panel The front panel and rear panel of the real product might be different from the images in this manual. These differences do not affect the functions of the product.
1.2.1 Front Panel Figure 1-2 shows the front panel of the HG865.
Figure 1-2 Front panel of the HG865
Table 1-1 describes the indicators of the HG865. Table 1-1 Indicators of the HG865
Indicator Status Description On The CATV function is enabled. CATV
Off The CATV function is disabled.
On The telephone interface is in the call status. Tel 1–Tel 2
Off The telephone interface is idle.
On The VoIP function is enabled. VoIP
Off The VoIP function is disabled.
On The device is connected to the Ethernet.
Off The device is not connected to the Ethernet.
GE, FE 1–FE 3
Blink Data is being transmitted through the Ethernet interface.
Auth See the next table See the next table.
Link See the next table See the next table.
On The HG865 is powered on. Power
Off The HG865 is powered off.
NOTE GE = Gigabit Ethernet FE = Fast Ethernet
1 Getting to Know the HG865 EchoLife HG865
Service Manual
1-4 Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
Issue 02 (2008-10-17)
Link and Auth indicate the states of the GPON interface on the HG865 when connecting to an OLT. Table 1-2 describes status of the Link indicator and the Auth indicator. Table 1-2 Status of the Link indicator and the Auth indicator
Status
Link Auth
Description
Off Off Initial state
Slow blink (1 Hz) Off Standby state
Fast blink (3 Hz) Slow blink (1 Hz) Serial-number state
Fast blink (3 Hz) On Ranging state
On On Operation state
Fast blink (3 Hz) Off POPUP state
On Off Emergency-stop state
1.2.2 Rear Panel
With a lightning protection mechanism, the HG865 stops running automatically if the
voltage of lightning exceeds the nominal value. It is recommended to disconnect the power supply from the HG865 in a lighting
weather.
Figure 1-3 shows the rear panel of the HG865.
Figure 1-3 Rear panel of the HG865
CATV Battery Monitor Optical FE1 FE2 FE3 GE Tel1 Tel212V;2A
Table 1-3 describes the external interfaces of the HG865.
EchoLife HG865 Service Manual 1 Getting to Know the HG865
Issue 02 (2008-10-17) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
1-5
Table 1-3 External interfaces of the HG865
Interface/Button Function CATV CATV signal interface. It is used to connect to a TV or a
digital STB.
Battery monitor External battery monitoring interface (reserved, not supported temporarily)
Optical GPON interface. It is used to connect the HG865 to an upper-layer device of the optical network.
GE, FE 1–FE 3
GE is an auto-sensing 10/100/1000 Base-T Ethernet interface. FE 1–FE 3 are auto-sensing 10/100 Base-T Ethernet interfaces. They are used to connect to other network devices, such as a computer, IP STB, or switch. The four Ethernet interfaces can be used simultaneously.
Tel 1–Tel 2 VoIP telephone interfaces. They are used to connect to telephones or fax machines to provide the VoIP or FoIP service. Two VoIP users can make calls at the same time.
12V; 2A Power interface. It is used to connect to the power adapter or the BBU.
ON/OFF It is used to power on or off the device.
NOTE BBU = Battery Backup Unit
EchoLife HG865 Service Manual 2 Installation Guide
Issue 02 (2008-10-17) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
2-1
2 Installation Guide
2.1 Installing the HG865
2.1.1 Installing the HG865 Against the Wall
Ensure that the positioning screws on the wall are installed firmly.
You can mount HG865 on the wall. There are two mounting holes at the bottom of the HG865. Fi
oles at the bottom
gure 2-1shows the distance between the mounting holes.
Figure 2-1 Distance between the mounting h
190mm
2.1.2 In
ories to the grooves on the bottom
Step 2 hoose an appropriate platform to place the HG865.
stalling the HG865 on a Platform This section describes how to install the HG865 on a platform. Ensure that the platform is stable. Do not place any object on the HG865. Keep a distance of at least 10 cm around or above the HG865 for heat dissipation.
Step 1 Attach four plastic feet obtained in the delivery accessof the HG865. C
2 Installation Guide EchoLife HG865
Service Manual
2-2 Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
Issue 02 (2008-10-17)
2.2 Cable Connection
Before connecting the HG865, turn off the power supply of devices such as your computer, STB, and switch.
Figure 2-2 shows the connection of the HG865 with devices.
Figure 2-2 Connection of the HG865 with devices
6 73 4
4
5
82
1
CATV Battery Monitor Optical FE1 FE2 FE3 GE Tel1 Tel212V;2A
1 Optical interface on the wall 2 TV 3 IP STB 4 PC 5 Switch 6 Fax machine 7 Telephone 8 Power adapter
See Figure 2-2, and do the following to connect the HG865:
Step 1 Connect the optical outlet on the wall to the Optical interface of the HG865 by using an optical fiber.
Step 2 Connect the CATV interface of the HG865 to the CATV interface of a TV or a digital STB by using a coaxial cable.
Step 3 Connect the GE (or FE 1–FE 3) interface of the HG865 to the network interface of a PC (or the upstream interface of a switch) by using an Ethernet cable.
Step 4 Connect the Tel 1 or Tel 2 interface of the HG865 to a telephone by using a telephone line.
Step 5 Connect the 12V; 2A interface of the HG865 to a power socket by using the power adapter (or the BBU). ----End
EchoLife HG865 Service Manual 2 Installation Guide
Issue 02 (2008-10-17) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
2-3
2.3 Software Loading
2.3.1 Setting Up Configuration Environment
Remote Maintenance The HG865 supports the remote Telnet maintenance. When configure the HG865 through the Telnet, do not randomly change the IP address of the HG865. If it is necessary to change the IP address, the Telnet connection will be disconnected after the change. You need to log in again with the new IP address to set up the connection. Figure 2-3 shows the networking for the remote Telnet maintenance through the WAN.
Figure 2-3 Networking for the remote Telnet maintenance through the WAN
1
2
3
4
5
1 Remote maintenance terminal 2 WAN 3 Switch 4 OLT 5 HG865
The following steps describes the procedure for setting up the configuration environment. Take the Windows XP operating system as an example.
Step 1 Ensure that the maintenance terminal and the HG865 are correctly connected. Ping the public network address of the HG865 (such as ping 11.11.11.1). If the address can be pinged through, it indicates that the connection between the maintenance terminal and the HG865 is established.
In the general configuration mode, use the display ipaddress command to view the public network IP address of the HG865.
Step 2 Select start > Run to display the Run text box.
2 Installation Guide EchoLife HG865
Service Manual
2-4 Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
Issue 02 (2008-10-17)
Step 3 Enter the Telnet command and the IP address of the public network of the HG865 in the Run text box, for example, telnet 11.11.11.1.
Step 4 Click OK to enter the Telnet running dialog box. After the connection with the HG865, the related information of the Telnet is displayed on the dialog box.
Step 5 Enter the correct user name and password. Then you can enter the configuration environment. (The preset user name of the terminal is root and the password is admin.) ----End
The IP addresses of the maintenance terminal and the HG865 may not be at the same network section. Ensure that the two IP addresses can be pinged through by each other.
Local Maintenance The HG865 supports the local maintenance through the LAN interfaces. The HG865 provides the maintenance IP address as 192.168.100.1. You can set the IP address of the client in the same network segment of the maintenance IP address. You can log in to the HG865 through Telnet.
NOTE Use the Ethernet cable to connect the maintenance terminal with the HG865. If the network port indicators on the maintenance terminal and the HG865 are both on, it indicates that the network connection is established.
2.3.2 Configuring the File Transfer Server The HG865 supports file transfer through FTP. To configure the FTP server, install the client software of the FTP server.
2.3.3 Loading Files Through FTP The procedure for installing a protocol is as follows.
Step 1 Configure the FTP server. Step 2 Run the FTP server on the remote maintenance terminal. Step 3 Execute load HG865 in the maintenance terminal to load the compressed file. Step 4 Execute reboot to reboot the system to enable the new program.
----End
Example: The IP address of the FTP server is 172.21.50.91; the user name is admin; the authentication password is admin; the loading path is the default value; the loading file name is upgrade.bin. The procedure is as follows.
Step 1 Log in to the HG865 through the Telnet mode. Step 2 Enter the privilege mode.
EchoLife HG865 Service Manual 2 Installation Guide
Issue 02 (2008-10-17) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
2-5
TERMINAL#enable
Step 3 Execute the load command. TERMINAL#load HG865 ftp 172.21.50.91 admin admin upgrade.bin
Step 4 Restart the system to validate the configuration. TERMINAL#reboot Are you sure to reset system? Caution:Unsaved data will be lost![Y|N]:Y
----End
After executing the load command, the upgrade process is displayed. When the loading completes, the prompt that the upgrade is successful is displayed. During the upgrade, do not restart the system or power off the supply.
EchoLife HG865 Service Manual 3 Configuration Guide
Issue 02 (2008-10-17) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
3-1
3 Configuration Guide
3.1 Serk is normally connected, the
enables PCs to access the network through the
01C02 supports Media Gateway Control Protocol (MGCP)
rvice Description The HG865 supports the VoIP service. When the netwovoice call can be realized after the HG865 successfully registers to the media gateway controller (MGC) server, for example, the softswitch. The HG865 supports the data service. It Lan interfaces. The HG865 has two software versions: HG865 V100R001C01 supports Session Initiation Protocol (SIP) HG865 V100R0
In this chapter, the HG865 serves as a media gateway (MG) and the softswitch device serves as a MGC.
3.2 BaBefore the configuration, make sure that you master the usage of command lines, which
vice.
3.2.1 C
For e, > indicates the user mode, and # indicates the privilege mode.
the system to HG865.
mand is executed successfully, and the hostname has been changed into HG865.
sic Command
is a means to configure the de
ommand Structure The command prompt consists of two parts: fixed character string and command mode identifier.
In the privilege mode, you can use the hostname method to configure the fixed character string. By default, the fixed character string of the system is TERMINAL.
mmand mode identifier indicates the mode of the current command. The coexampl
Example: Modify the default hostname of TERMINAL#hostname HG865 HG865#
This com
3 Configuration Guide EchoLife HG865
Service Manual
3-2 Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
Issue 02 (2008-10-17)
3.2.2 Command Modes Command modes of the HG865 include the user mode, privilege mode, general configuration mode, advanced configuration mode, and GPON mode. The privilege mode and the general configuration mode are compatible with the lower authority modes.
In the privilege mode, you can run all commands in the user mode. In the general configuration mode, you can run all commands in the user mode and
the privilege mode. Figure 3-1 shows the relationships between the command modes. An ellipse represents a command mode. An arrow indicates the switching from one mode to another mode. Commands are listed above the arrows.
Figure 3-1 Relationships between the command modes
Exit Enable
Disable
Configureterminal
ExitE
xit
GPO
N
GPONmode
Advancedconfiguration mode
Privilegemode
Usermode
To switch from the privilege mode to the general configuration mode, execute configure terminal. To exit from the general configuration mode and enter the privilege mode, execute exit.
3.2.3 Online Help of Command Line The command interface provides the following online helps.
Complete Help Enter ? in any view, and then you can get all the usable commands under the view and the concise descriptions of the commands.
Partial Help Enter ? after a command separated by a space. If that position is a keyword, all
keywords and their concise descriptions will be listed. Enter ? after a command separated by a space. If that position is a parameter, the
descriptions of all related parameters will be listed.
EchoLife HG865 Service Manual 3 Configuration Guide
Issue 02 (2008-10-17) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
3-3
Enter ? after a character string. All the commands beginning with the character string will be listed.
Add a space after a command. If that position is a keyword, the keywords of the command will be completed.
3.2.4 Common Commands
To avoid data loss due to exceptional system reset or power-off, save settings in time by executing the command write.
Table 3-1 describes the common commands in the HG865. Table 3-1 Common commands
To… Execute… Access the privilege mode TERMINAL>enable
Access the general configuration mode TERMINAL#configure terminal
Exit the current mode and access the user mode
disable (any mode)
Exit the current mode and access the upper-level mode or exit the configuration environment
exit (any mode)
Save the settings TERMINAL#write
Set the hostname TERMINAL#hostname
Query the version TERMINAL>display version
Change the password TERMINAL(config)#terminal user
Set the system time TERMINAL#time
Set the region information TERMINAL(config)#region { CN | HK | BR | EG | GB | CL | SG | US }
Set the timeout interval TERMINAL#terminal timeout timeout
Update the software version TERMINAL#load hg865 ftp_server username password filename
3 Configuration Guide EchoLife HG865
Service Manual
3-4 Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
Issue 02 (2008-10-17)
3.3 SIP Service Configuration
3.3.1 SIP Networking Method Figure 3-2 shows the SIP networking.
Figure 3-2 SIP networking
5
6
4
3
7
2
1
1 Softswitch 2 IP Network 3 Switch 4 OLT 5 HG865 6 Telephone 7 PC
3.3.2 SIP Configuring Commands Configure commands as follows.
Operation Command Configure the SIP server. TERMINAL(config)#sip server index
{ address address | domain name | port port | expire-time expire-time }
Configure the SIP user information.
TERMINAL(config)#sip user user-sn { id id | password password | name name }
Log out the SIP user. TERMINAL(config)#( undo) sip shutdown { user-sn | all }
EchoLife HG865 Service Manual 3 Configuration Guide
Issue 02 (2008-10-17) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
3-5
Operation Command Configure the SIP user digitmap. TERMINAL(config)#sip digitmap digitmap
Configure the SIP local port number.
TERMINAL(config)#sip local-port localport
Display the SIP user attribute. TERMINAL(config)#display sip attribute
Display the SIP digitmap. TERMINAL(config)#display sip digitmap
Display the SIP send-capability. TERMINAL(config)#display sip send-capability
Display the SIP server information.
TERMINAL(config)#display sip server
Display the SIP software parameters.
TERMINAL(config)#display sip soft-parameter
3.3.3 Configuring SIP Data
Configuring the IP Address of the HG865 In the general configuration mode, configure the IP address of the HG865. The configuration commands are listed as follows.
Operation Command Configure the HG865 to obtain a static IP address: ipaddress static ip-address net-mask gateway-ip
Configure the HG865 to obtain an IP address automatically: ipaddress dhcp
Configure the IP address of the HG865
Configure the HG865 to obtain an IP address by the PPPoE dialing:
pppoe username username password password ipaddress pppoe
The IP address of the HG865 must be configured. After being configured, the IP address can take effect at once without rebooting. The IP address of the HG865 can be obtained in three ways:
By Configuring a fixed IP address From DHCP server Through the PPPoE dialing mode
For the SIP HG865, DHCP is the default method of obtaining the IP address.
3 Configuration Guide EchoLife HG865
Service Manual
3-6 Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
Issue 02 (2008-10-17)
Configuring SIP Serve In the general configuration mode, configure the information of the call server, which SIP HG865 registers to. The configuration command is listed as follows.
Command Remarks TERMINAL(config)# sip server index { address address | domain name | port port | expire-time expire-time }
Index: Index of server, ranging from 0 to 2. address: The IP address of the server. name: The user domain name. The length
should not exceed 63 characters. port: The port number of the server. The
default is 5060. expire-time: Registration validity period. The
range is 5s–3600 × 24 × 365s. The default is 120s.
Example: Configure the IP address of the server 2 as 191.168.3.3 and the port number as 5061.
Step 1 Configure the information of the SIP server. TERMINAL(config)#sip server 2 address 191.168.3.3 port 5061 { <cr>|domain<K>|expire-time<K> }: Comman sip server 2 address 191.168.3.3 port 5061 Execution of command succeeded
Step 2 Query the configuration result. TERMINAL(config)#display sip server { <U><0,2>|all<K> }:2 Command: display sip server 2 Sip Server Information ---------------------------------------------- index : 2 user domain : domain name : IP address : 191.168.3.3 port : 5061 expire time : 3600 ----------------------------------------------
----End
Configuring SIP User This command is used to configure the information of the SIP user, including user telephone number, call authentication password and user alias. In the general configuration mode, the command is listed as follows.
EchoLife HG865 Service Manual 3 Configuration Guide
Issue 02 (2008-10-17) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
3-7
Command Remarks TERMINAL(config)#sip user user-sn { id id | password password | name name }
user-sn: The port number of the connected HG865. Its range varies according to the actual port quantity of the devices in use. For example, the HG865 has two ports. The port number ranges from 0 to 2.
id: User SIP ID. It is used to identify the user and the length should not exceed 31 characters. The number is allocated by the service provider and has been configured on the SIP server.
Password: User authentication password. The length should not exceed 31 characters. The service provider decides whether to configure the parameter.
Name: User alias. The length should not exceed 63 characters.
The ID and the password must be configured on the registration server firstly and then the user can succeed in registering.
Example: Configure user-sn as 0, id as 88889999, password as abcxyz, and name as Jack.
Step 1 Configure the SIP user. TERMINAL(config)#sip user 0 id 88889999 password abcxyz name Jack This operation will affect the user's current services. Continue? [Y/N]:y Execution of command succeeded. TERMINAL(config)#
Step 2 Query the configuration result. TERMINAL(config)#display sip attribute 0 Sip User Information ----------------------------------------------- user-sn : 0 id : 88889999 password : ******** name : jack local address : 172.21.100.29 local-port : 5060 registration state : registered expire-time : 0 sec previous server : 0.0.0.0 : 5060 current server : 191.168.100.8 : 5060 -----------------------------------------------
3 Configuration Guide EchoLife HG865
Service Manual
3-8 Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
Issue 02 (2008-10-17)
----End
In the general configuration mode, execute undo sip user to delete the SIP user; execute sip shutdown to enable the user to log out.
Configuring SIP User Digitmap This command is used to configure the restriction rules when the user dials a number. The default rule of the SIP HG865 is that the user is permitted to enter any character or number when the user is dialing a number. This rule may be modified according to the actual requirement.
Command Remarks TERMINAL(config)#sip digitmap digitmap
Digitmap: The digitmap string to be added. The length is 1–31. The valid characters that may be contained in the string: 0–9, a, b, c, d, x. x is wildcard and can represent any number. The default digitmap of the SIP HG865 is [xABCD*#].t.
Execute undo sip digitmap to cancel user digitmap. Execute display sip digitmap to view user digitmap information. Example: Delete the default digitmap, the configured digitmap string is 0755xxxxxxxx. Only the number starting with 0755 is permitted to be dialed.
Step 1 Delete the default SIP digitmap. ERMINAL(config)#display sip digitmap Sip digitmap -------------------------------------- index digitmap ----- -------------------------------- 0 [XABCD*#].T -------------------------------------- TERMINAL(config)#undo sip digitmap 0 { <cr>|<U><0,15> }: Command: undo sip digitmap 0 [XABCD*#].T is deleted Execution of command succeeded
Step 2 Configure SIP user digitmap. TERMINAL(config)#sip digitmap 0755xxxxxxxx Execution of command succeeded. TERMINAL(config)#
Step 3 Query the configuration result. TERMINAL(config)#display sip digitmap
EchoLife HG865 Service Manual 3 Configuration Guide
Issue 02 (2008-10-17) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
3-9
Sip digitmap -------------------------------------- index digitmap ----- -------------------------------- 0755xxxxxxxx --------------------------------------
----End
Configuring Signaling Port Number of SIP The command is used to configure the local port number, which is used by the HG865 to send the SIP signaling. The default SIP signaling port number is 5060. It can be modified through the following command.
Command Remarks TERMINAL(config)#sip local-port port
local-port: Local port number. The value cannot be the same with other port numbers. The default is 5060.
Example: Configure the local port number as 5061.
Step 1 Configure the local port number. TERMINAL(config)#sip local-port 5061 Execution of command succeeded
Step 2 Query the configuration result. TERMINAL(config)#display sip attribute all Sip User Information --------------------------------------------------- user-sn : 0 id : 88889999 password : ******** name : jack local address : 172.21.100.29 local-port : 5061 registration state : registering expire-time : 0 sec previous server : 0.0.0.0 : 5060 current server : 191.168.3.3: 5061----------------------------------------------- TERMINAL(config)#
----End
3 Configuration Guide EchoLife HG865
Service Manual
3-10 Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
Issue 02 (2008-10-17)
After the SIP configuration completes, connect the HG865 with a telephone according to 2.2 "Cable Connection" and then pick up the telephone. If you hear a beep, the configuration is successful.
3.4 MGCP Service Configuration
3.4.1 MGCP Networking Method Figure 3-3 shows the MGCP networking.
Figure 3-3 MGCP networking method
5
6
4
3
7
2
1
1 Softswitch 2 IP network 3 Switch 4 OLT 5 HG865 6 Telephone 7 Fax machine
3.4.2 MGCP Configuration Commands Table 3-2 lists the MGCP configuration commands. Table 3-2 MGCP configuration commands
To… Run… Set the MG domain name for registration
TERMINAL(config)#mgcp mg-domain-name name
EchoLife HG865 Service Manual 3 Configuration Guide
Issue 02 (2008-10-17) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
3-11
To… Run… Set the MGC information TERMINAL(config)#mgcp mgc index address str
Set the authentication mode to the GB mode
TERMINAL(config)#mgcp authentication gb-mode {mgiD | mgkl }
Set the authentication mode to the HW mode
TERMINAL(config)#mgcp authentication hw-mode key keyword
Set the signaling port number of the MG
TERMINAL(config)#mgcp mg-port port
Set the signaling port number of the MGC server
TERMINAL(config)#mgcp mgc index port port
Set the DNS domain name TERMINAL(config)#dns domain-name name
Set the IP address of the DNS server
TERMINAL(config)#dns server first { second }
NOTE DNS = Domain Name System
3.4.3 Configuring MGCP Data
Configuring IP Address of the HG865 In general configuration mode, configure the IP address of the HG865. The configuration commands are as follows.
To… Run… To obtain a fixed IP address: ipaddress static ip-address net-mask gateway-ip
To automatically obtain an IP address: ipaddress dhcp
Configure the IP Address of the HG865
To obtain an IP address by the PPPoE dialing: pppoe username username password password ipaddress pppoe
The IP address of the HG865 must be configured. After the configuration, the IP address can take effect at once without restarting the HG865. The IP address of the HG865 can be obtained in the following methods:
By configuring a fixed IP address From the DHCP server Through the PPPoE dialing mode
3 Configuration Guide EchoLife HG865
Service Manual
3-12 Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
Issue 02 (2008-10-17)
The HG865 can only configure one mode to obtain the IP address.
When you are dynamically obtaining the IP address, such as through the Dynamic Host Configuration Protocol (DHCP) and PPPoE modes, you need not configure the DNS server information.
Configuring the MG Domain Name for Registration In general configuration mode, configure the domain name of the HG865.
Command Remarks TERMINAL(config)#mgcp mg-domain-name name
name: The domain name of the HG865, containing 1–60 characters. The domain name should be consistent with that configured on the MGC server.
Example: Configure the domain name of the HG865 as huawei.com.
Step 1 Configure the MG domain name for registration. TERMINAL(config)#mgcp mg-domain-name huawei.com
Step 2 Query the configuration result. TERMINAL(config)#display mgcp attribute ======================================================== MGIP MG-PORT MG-DOMAIN-NAME 10.70.33.62 2427 huawei.com ============================================== MGC-IP1 MGC-PORT1 MGC-DOMAIN-NAME1 0.0.0.0 2727 - ============================================== MGC-IP2 MGC-PORT2 MGC-DOMAIN-NAME2 0.0.0.0 2727 - ============================================== MG-STATE REGISTERED-MGC Fault 1 ============================================== AUTH-MODE KEY Huawei mode -
----End
Configuring the MGC Information In general configuration mode, configure the IP address or domain name of the HG865. The configuration commands are as follows.
EchoLife HG865 Service Manual 3 Configuration Guide
Issue 02 (2008-10-17) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
3-13
Command Remarks TERMINAL(config)#mgcp mgc index address str
index :The index of the softswitch to which the gateway can register, ranging from 1 to 2. str: It contains 1–60 characters. It can be a domain name or an IP address. Configure it as a domain name or an IP address
Example: Configure the IP address of the server for registration as 210.11.180.18. The signaling port number is 2727 by default
Step 1 Configure the IP address. TERMINAL(config)#mgcp mgc 1 address 210.11.180.18 { <cr>|port<K> }: Command: mgcp mgc 1 address 210.11.180.18
Step 2 Query the configuration result. TERMINAL(config)#display mgcp attribute =============================================== MGIP MG-PORT MG-DOMAIN-NAME 10.70.33.62 2427 huawei.com =============================================== MGC-IP1 MGC-PORT1 MGC-DOMAIN-NAME1 210.11.180.18 2727 - =============================================== MGC-IP2 MGC-PORT2 MGC-DOMAIN-NAME2 0.0.0.0 2727 - =============================================== MG-STATE REGISTERED-MGC Fault 1 =============================================== AUTH-MODE KEY Huawei mode -
----End
Configuring MG Authentication Information To prevent the illegal MG from registering to the MGC, start registration authentication on the MG. The commands are as follows.
To… Run… Set the authentication mode to the GB mode
TERMINAL(config)#mgcp authentication gb-mode {mgiD | mgkl }
Set the authentication mode to the HW mode
TERMINAL(config)#mgcp authentication hw-mode key keyword
3 Configuration Guide EchoLife HG865
Service Manual
3-14 Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
Issue 02 (2008-10-17)
The HW authentication mode is a private authentication procedure of Huawei. The GB
authentication mode is defined by Ministry of Information Industry.
When the encryption algorithm of the SoftX3000 is MD5, you need to set the authentication mode of the interconnected HG865 to the HW mode. When the encryption algorithm of the SoftX3000 is DH, you need to set the authentication mode of the interconnected HG865 to the GB mode.
Example: Configure the HG865 to register to the call server in HW mode. The registration key configured on the server is HG865register. Then, query the result after the configuration.
Step 1 Configure the authentication mode to HW and the authentication key. TERMINAL(config)#mgcp authentication hw-mode key Please input your keyword<1~16 characters>:************* Please input again:*************
Step 2 Query the configuration result. TERMINAL(config)#display mgcp attribute =============================================== MGIP MG-PORT MG-DOMAIN-NAME 191.168.208.13 2427 - =============================================== MGC-IP1 MGC-PORT1 MGC-DOMAIN-NAME1 0.0.0.0 2727 - =============================================== MGC-IP2 MGC-PORT2 MGC-DOMAIN-NAME2 0.0.0.0 2727 - =============================================== MG-STATE REGISTERED-MGC Fault 1 =============================================== AUTH-MODE KEY Huawei mode *******
----End
Setting the Signaling port number of the MG Device By default, the protocol port number of the transport layer of the MG device is 2427. To change it, run the following command.
Command Remarks TERMINAL(config)#mgcp mg-port port
port: Port number. By default, it is 2427. The default port number is recommended.
Setting the Signaling port number of the MGC Server
EchoLife HG865 Service Manual 3 Configuration Guide
Issue 02 (2008-10-17) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
3-15
By default, the protocol port number of the transport layer of the MGC server is 2727. To change it, run the following command.
Command Remarks TERMINAL(config)#mgcp mgc index port port
index: index of the MGC server. port: protocol port number of the transport layer. By default, it is 2727. The default port number is recommended.
Configuring DNS After enabling the DNS client, the HG865 can access other network devices by the domain name. The relevant commands are as follows.
To… Run… Set the DNS domain name TERMINAL(config)#dns domain-name name Set the IP address of the DNS server
TERMINAL(config)#dns server first { second }
Obtain the configuration of the DNS automatically through the DHCP or PPPoE server
TERMINAL(config)#dns auto
Example: Start the DNS client on the HG865. Set the domain name of the DNS domain as tele.com and the IP address of the DNS server as 210.11.123.13.
Step 1 Set the domain name of the DNS. TERMINAL(config)#dns domain-name tele.com
Step 2 Set the IP address of the DNS server. TERMINAL(config)#dns server 210.11.123.13 { <cr>|<I> }: Command: dns server 210.11.123.13
Step 3 Query the configuration result. TERMINAL(config)#display dns ----------------------------------------------- DNS mode: STATIC ----------------------------------------------- DNS suffix:tele.com Server address: ....Main DNS Server.............: 210.11.123.13 -----------------------------------------------
3 Configuration Guide EchoLife HG865
Service Manual
3-16 Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
Issue 02 (2008-10-17)
----End
After the configuration of the MGCP completes, connect the telephone and then pick up the phone according to section “2.2 Cable Connection" If you can hear a buzz sound, it indicates that the MGCP is configured successfully.
EchoLife HG865 Service Manual 4 Operation Guide
Issue 02 (2008-10-17) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
4-1
4 Operation Guide
4.1 U ing a Telephs one Step 1
to a telephone. Ensure that the ected.
Step 3
uration Guide" Step 4
hone. Enter the number that you want to dial. Wait for an answer. ----End
s B Step 1
ect to an IP STB. Ensure that the STB
Step 2 and the IP STB.
Step 3 listen to programs according to the prompt on the TV screen.
----End
Connect the HG865. ble Connection" to connect Refer to section 2.2 "Ca
telephone and the HG865 are correctly connStep 2 Power on the HG865.
Configure the VoIP service of the HG865. For details, refer to section 3 "ConfigEnjoy the high-speed voice service. Pick up the telep
4.2 U ing an IP STConnect the HG865 Refer to section 2.2 "Cable Connection" to connand the HG865 are correctly connected. Power on the HG865, the TVThree modes are available:
Preset a fixed IP address. Obtain an IP address from a DHCP server.
PPPoE dialing mode. Obtain an IP address through the Contact your service provider for which mode to use.
e high-speed video service. Enjoy thWatch or
4 Operation Guide EchoLife HG865
Service Manual
4-2 Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
Issue 02 (2008-10-17)
4.3 Using a PC Step 1 Connect the HG865.
Refer to section 2.2 "Cable Connection" to connect to a PC. Ensure that the PC and the HG865 are correctly connected.
Step 2 Power on the PC and the HG865. Step 3 Set the IP addresses of the PC.
Three modes are available: Preset a fixed IP address Obtain an IP address from a DHCP server Obtain an IP address through the PPPoE dialing mode
Contact your service provider for which mode to use. Step 4 Enjoy the high-speed data service.
Enable the Internet Explorer to surf on the Internet. ----End
4.4 Using a TV or a Digital STB
The CATV interface is used to connect to a TV or a digital STB. Please contact your service provider for which device to be connected.
Step 1 Refer to section 2.2 "Cable Connection" to connect to a TV or a digital STB. Ensure that the TV or digital STB and the HG865 are correctly connected.
Step 2 Power on the HG865, the TV, and the digital STB. Step 3 Watch or listen to programs according to the prompt on the TV screen.
----End
EchoLife HG865 Service Manual 5 Troubleshooting
Issue 02 (2008-10-17) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
5-1
5 Troubleshooting
The CAer to check that you have subscribed to the CATV function.
The Po
N/OFF button on the rear panel is pressed.
The Lin
ean.
The LinThe HG865 may not receive the downstream optical signal sent by the service provider.
help.
The GE
r there are devices marked with ? or ! under Network adapters. If there are such devices, uninstall and then re-install them, or insert the network adapter into
The Te
e line is correct. Check whether the telephone is on-hook.
TV indicator is off Contact the service provid
wer indicator is off Check whether the power adapter matches the HG865.
Check whether the power connection is correct.
Check whether the O
k indicator is off This indicates that the upstream connection authentication is not successful.
Check whether the optical fiber is connected properly. Check whether the optical connectors are damaged or uncl
k indicator is on, but the Auth indicator is off
Contact the service provider for
and FE indicator is off Check whether the provided Ethernet cable is used. ly. Check whether the Ethernet cable is connected proper Check whether the indicator of the network adapter is on.
Check whether the network adapter works normally. Check whethe
another slot.
l indicator is off Check whether the telephone line matches th Check whether the connection of the telephon
e HG865.
EchoLife HG865 Service Manual 6 Technical Specifications
Issue 02 (2008-10-17) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
6-1
6 Technical Specifications
Physica
t interfaces (RJ-45) nterfaces (RJ-11)
Protoco
, IEEE 802.3ab nd T38, RTP/RTCP, SIP
Physica6 mm
Hz
Operating environment humidity: 5%–95% (non-condensing)
l Interfaces One CATV interface
One Battery Monitor interface One Optical interface thernet interface (RJ-45) One auto-sensing 10/100/1000 Base-T E
/100 Base-T Etherne Three auto-sensing 10 Two VoIP telephone i One Power interface
ls and Standards GPON: ITU-T G.984.x GE / FE: IEEE802.1p, IEEE 802.3u, IEEE802.1q VoIP: G.711A/u, a
l Specifications Dimensions (L × W × H): 275 mm × 205 mm × 4 Weight: About 910 g
–60 Power adapter input: 100–240 V AC, 50 Whole-device power supply: 12 V DC, 2 A Standard power consumption: < 15 W Operating environment temperature: 0℃ to +40℃
EchoLife HG865 Service Manual A SIP Service Configuration
Issue 02 (2008-10-17) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
A-1
A SIP Service Configuration
A.1 Voice Service Configuration
A.1.1 C When the DHCP server is
ed on, the HG865
dress information: ss
-8a-2a
RUNNING
.17 th .....: 60 S
UNNING
----------------------
A.1.2 Crver as
8.10.10
onfiguring IP Address The HG865 obtains the IP address through DHCP by default.configured, and the HG865 is connected to the network and powerobtains the IP address from the DHCP server automatically. Run the following command to query the IP adTERMINAL(config)#display ipaddre
The information is displayed as follows: --------------------------------------------------
m DNS Domain Name...............: abc.co........: 00-e0-fc-92 Physical Address......
IP Address Get Method.........: DHCP esw (unit number 3):
Flags: (0x68243) UP BROADCAST MULTICAST ARP IP Address..................: 191.168.100.2 Subnet Mask.................: 255.255.0.0
8.10.10 Default Gateway.............: 191.16DHCP Server Address...........: 191.168.210
DHCP Expired Time Leng esw (unit number 4): Flags: (0x68243) UP BROADCAST MULTICAST ARP R IP Address..................: 192.168.100.1 Subnet Mask.................: 255.255.255.0 ----------------------------
onfiguring SIP Server Run the following command to configure the IP address of the SIP se192.168.10.10:
onfig)#sip server 0 address 191.16TERMINAL(c{ <cr>|domain<K>|port<K>|expire-time<K> }:Command: sip server 0 address 191.168.10.10 Execution of command succeeded
A SIP Service Configuration EchoLife HG865
Service Manual
A-2 Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
Issue 02 (2008-10-17)
om ress<K>|port<K>|expire-time<K> }:
ver.com n of command succeeded”
Configure the address of the SIP server as sipserver.com. TERMINAL(config)#sip server 0 domain sipserver.c{ <cr>|add Command: sip server 0 domain sipserExecutio
You can configure three SIP servers for the HG865. If the HG865 fails to register to the first SIP server, then it registers to the second one. If it fails to register to the second SIP server, it re
gisters to the third one. The SIP servers
f Server 2 as that of the standby server. This can
A.1.3 Command to configure the three parameters for the SIP user.
p user 0 id 88880008 password 88880008 e<K> }:
affect the user's current services. Continue?
n of command succeeded
here can be configured from 0 to 2. It is recommended to configure the address of Server 0 as that of the main server and the IP address oshorten the register time.
onfiguring SIP User Information Run the following c
Port number: 0 ID: 88880008 Authentication password: 88880008
TERMINAL(config)#si{ <cr>|nam Command: sip user 0 id 88880008 password 88880008 This operation will[Y/N]:y TERMINAL(config)# Executio
The HG865 can configure two SIP users, which range from 0 to 1.
A.1.4 Querying Configuration Result
-------------------------
Query the configuration result. TERMINAL(config)#display sip attribute 0
Information Sip User----------------------------user-sn : 0
08 id : 888800password : ******** name : local address : 191.168.100.2local-port : 5060
EchoLife HG865 Service Manual A SIP Service Configuration
Issue 02 (2008-10-17) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
A-3
red 00 sec
server : 191.168.10.10 : 5060
registration state : registeexpire-time : 3previous server : current
The HG865 can configure two users. You can configure the sip user to 0, 1 and all to check the information of the SIP user(s).
uration, run the write command to save the data.
wait a moment...... ata backup percent is: 100%
TERMINAL(config)#
address of online service.
Figure A-1 shows the ervice.
A.1.5 Saving Configuration Data After the data configTERMINAL#write Command executing, please wait... System starts to save configuration data, please The configuration d
A.2 Data Service Configuration
A.2.1 Online Service The HG865 supports the online service. Connect the cables; configure the IPyour PC, and power on your PC. Then you can enjoy the
connection for the online s
Figure A-1 Connection for the online service
CATV Battery Monitor Optical FE1 FE2 FE3 GE Tel1 Tel212V;2A
2
3
22 2
1
1 Optical interface on the wall 2 PC 3 Switch
A SIP Service Configuration EchoLife HG865
Service Manual
A-4 Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
Issue 02 (2008-10-17)
A.2.2 Fax Service By default, the HG865 supports the fax service. Figure A-2 shows the connection for the fax service.
Figure A-2 Connection for the fax service
2
1
CATV Battery Monitor Optical FE1 FE2 FE3 GE Tel1 Tel212V;2A
1 Optical interface on the wall 2 Fax machine
If you want to change the fax mode, contact your service provider for help.
EchoLife HG865 Service Manual B MGCP Service Configuration
Issue 02 (2008-10-17) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
B-1
B MGCP Service Configuration
B.1 Voice Service Configuration
B.1.1 Cn of the HG865:
nue?[Y|N]:y
........: 00-e0-fc-15-64-18
RUNNING
........: 10.70.33.60
UNNING
--
B.1.2 Cthe default signaling
com
B.1.3 Cprotocol port
onfiguring IP Address Co figure the following parameters
Fixed IP address: 10.70.33.62 Subnet mask: 255. 255.0.0
Default gateway: 10.70.33.60 TERMINAL(config)#ipaddress static 10.70.33.62 255.255.0.0 10.70.33.60
rvice, conti Changing net parameter may affect current se-------------------------------------------------- DNS Domain Name...............: my.domain Physical Address...... IP Address Get Method.........: Static IP config esw (unit number 3): Flags: (0x68243) UP BROADCAST MULTICAST ARP IP Address..................: 10.70.33.62 Subnet Mask.................: 255.255.0.0
Default Gateway..... esw (unit number 4): Flags: (0x68243) UP BROADCAST MULTICAST ARP R IP Address..................: 192.168.100.1 Subnet Mask.................: 255.255.255.0 ------------------------------------------------
onfiguring Domain Name of the HG865 Configure the domain name of the HG865 as huawei.com. Use port number. TERMINAL(config)#mgcp mg-domain-name huawei.
onfiguring IP address of MGC Configure the MGC 1 IP address as 210.11.180.18. Use the default number.
B MGCP Service Configuration EchoLife HG865
Service Manual
B-2 Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
Issue 02 (2008-10-17)
RMINAL(config)#mgcp mgc 1 address 210.11.180.18 t<K> }:
ess mgc.com
=======
=================
===========
- ===================================
TERED-MGC
E KEY
TE{ <cr>|por Command: mgcp mgc 1 address 210.11.180.18
onfigure the address of the MGC 1 server as mgc.com. CTERMINAL(config)#mgcp mgc 1 addr
Query the configuration result. TERMINAL(config)#display mgcp attribute ================================================MGIP MG-PORT MG-DOMAIN-NAME 10.70.33.62 2427 huawei.com ======================================MGC-IP1 MGC-PORT1 MGC-DOMAIN-NAME1 210.11.180.18 2727 - ============================================MGC-IP2 MGC-PORT2 MGC-DOMAIN-NAME2 0.0.0.0 2727 ====================MG-STATE REGISFault 1 AUTH-MODHuawei mode -
The HG865 supports dual homing. You can configure two MGC servers for the HG865. When the HG865 fails to register to the first MGC, it registers to the second MGC. 1 indicates the first IP address of the MGC, while 2 indicates the
B.1.4 C
:55:00 2006-10-20
B.1.5 S
n eters of the DNS:
)#RMINAL(config)#dns server 210.11.123.13
}:
second IP address of the MGC.
onfiguring System Time Configure the system time as 11:55:00, 2006-10-20. TERMINAL(config)#time 11
tarting DNS Client Start the DNS client on the HG865. Co figure the following param
Domain name: tele.com IP address: 210.11.123.13
dns domain-name tele.com TERMINAL(configTE{ <cr>|<I> Command:
EchoLife HG865 Service Manual B MGCP Service Configuration
Issue 02 (2008-10-17) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
B-3
-------------------------------------------
Main DNS Server.............: 210.11.123.13 -------
B.1.6 Aent system as 210.11.123.33.
onfig)# mary 210.11.123.33
210.11.123.33
twork management system when the HG865
TERMINAL(config)#nms access on
B.1.7 Snd to save data.
onfig)#write te-carrier-config<K> }:
write Write running-config to flash ... Succeed!
onfiguration
B.2.1 OThe HG865 supports the online service. Connect the cables; configure the IP address of your PC, and power on your PC. Then you can enjoy the online service.
dns server 210.11.123.13 play dnsTERMINAL(config)#dis
------------------------------------------------------------ DNS mode: STATIC -----------------DNS suffix: tele.com Server address:
-----------------------------------------------------
dding HG865 Network Management System Configure the IP address of the
nms pri
HG865 network managemTERMINAL(c{ <cr>|secondary<K> }: Command: nms primary primary IP 210.11.123.33 config succeed
Configure the HG865 to register to the neis started.
config succeed
aving Configuration Data After the data configuration, use the write commaTERMINAL(c{ <cr>|generaCommand:
B.2 Data Service C
nline Service
B MGCP Service Configuration EchoLife HG865
Service Manual
B-4 Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
Issue 02 (2008-10-17)
Figure B-1 shows the connection for the online service.
Figure B-1 Connection for the online service
CATV Battery Monitor Optical FE1 FE2 FE3 GE Tel1 Tel212V;2A
2
3
22 2
1
1 Optical interface on the wall 2 PC 3 Switch
EchoLife HG865 Service Manual B MGCP Service Configuration
Issue 02 (2008-10-17) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
B-5
B.2.2 Fax Service The HG865 supports three fax modes: 711v2, T38v2, and T38v3. The default mode is T38v3. Figure B-2 shows the connection for the fax service.
Figure B-2 Connection for the fax service
2
1
CATV Battery Monitor Optical FE1 FE2 FE3 GE Tel1 Tel212V;2A
1 Optical interface on the wall 2 Fax machine
Querying Fax Mode To query the MGCP fax mode, do as follows: TERMINAL(config)#display mgcp soft-parameter ======================================================== MGC-TYPE REGISTER-MODE CW-TONE-MODE SoftX Wildcard mg ======================================================== FAX-MODE HOLD-FLAG CHARGE CONTROL 711v2 Off on
B MGCP Service Configuration EchoLife HG865
Service Manual
B-6 Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
Issue 02 (2008-10-17)
Configuring Fax Mode The methods to configure the three fax modes are similar. To configure the fax mode to 711v2, do as follows: TERMINAL(config)#advanced TERMINAL(advanced-config)# TERMINAL(advanced-config)#mgcp soft-parameter fax-mode 711v2 { <cr>|mgc-type<K>|register-mode<K>|hold-flag<K>|cw-tone-mode<K>|chargecontrol<K>|fax-port-add2<K> }: Command: mgcp soft-parameter fax-mode 711v2
EchoLife HG865 Service Manual C Acronyms and Abbreviations
Issue 02 (2008-10-17) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
C-1
C Acronyms and Abbreviations
C CATV able TV
ration Protocol NS omain Name Server
TP ile Transfer Protocol
PON igabit-Capable Passive Optical Network
PTV ternet Protocol Television
AN ocal Area Network
GCP edia Gateway Control Protocol
AT etwork Address Translation
C D DHCP Dynamic Host ConfiguD D F FoIP Fax over IP F F G G G I IP Internet Protocol I In L L L M MG Media Gateway MGC Media Gateway Controller M M N N N
C Acronyms and Abbreviations EchoLife HG865
Service Manual
C-2 Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
Issue 02 (2008-10-17)
trol Interface NT ptical Network Terminal
PPoE oint-to-Point Protocol over Ethernet
rotocol TP eal-time Transport Protocol
nd Home Office TB et-Top Box
G runk Gateway
oIP oice over IP
WAN Wide Area Network
O OLT Optical Line Terminal OMCI ONT Management and ConO O P PC Personal Computer PON Passive Optical Network POTS Plain Old Telephone Service PSTN Public Switched Telephone Network P P R RTCP Real-time Transport Control PR R S SIP Session Initiation Protocol SNTP Simple Network Time Protocol SOHO Small Office aS S T T T V V V W