3-d modal analysis lecture 10.pdf
TRANSCRIPT
-
7/28/2019 3-D modal Analysis lecture 10.pdf
1/23
-
Lecture 10
Dr. Mohammed Al-Hazmi
Slide 1
-
7/28/2019 3-D modal Analysis lecture 10.pdf
2/23
Mode analysis of a straight bar
Obtain the lowest six vibration modes and resonant frequencies of thestraight steel bar shown in Figure below
Thickness of the bar is 0.005 m, width is 0.01 m, and the length is0.09 m.
Material of the bar is steel with Youngs modulus, E =206 GPa, and =
. .
Density =7.8103 kg/m3.
Slide 2
.
-
7/28/2019 3-D modal Analysis lecture 10.pdf
3/23
-
7/28/2019 3-D modal Analysis lecture 10.pdf
4/23
5. Set element type
Main Menu: Preprocessor Element type Add/Edit/Delete
Slide 4
-
7/28/2019 3-D modal Analysis lecture 10.pdf
5/23
7. Assign material properties
Main Menu: Preprocessor Material Props MaterialModels
Slide 5
-
7/28/2019 3-D modal Analysis lecture 10.pdf
6/23
ANSYS Toolbar: SAVE_DB
Slide 6
-
7/28/2019 3-D modal Analysis lecture 10.pdf
7/23
9. Create geometry (rectangles)
Main Menu: Preprocessor Modeling Create Areas Rectangles By 2 Corners
Slide 7
-
7/28/2019 3-D modal Analysis lecture 10.pdf
8/23
Slide 8
-
7/28/2019 3-D modal Analysis lecture 10.pdf
9/23
14. Extrude Bicycle Wrench area Main Menu: Preprocessor Modeling Operate Extrude
by xyz offset
- Select Bicycle wrench area, OK
Slide 9
-
7/28/2019 3-D modal Analysis lecture 10.pdf
10/23
Slide 10
-
7/28/2019 3-D modal Analysis lecture 10.pdf
11/23
15. Set element size
Main Menu: Preprocessor Meshing Mesh tool
Slide 11
-
7/28/2019 3-D modal Analysis lecture 10.pdf
12/23
Slide 12
-
7/28/2019 3-D modal Analysis lecture 10.pdf
13/23
-
7/28/2019 3-D modal Analysis lecture 10.pdf
14/23
17. Analysis type
Main Menu: Solution Analysis Type New Analysis
Slide 14
-
7/28/2019 3-D modal Analysis lecture 10.pdf
15/23
Main Menu: Solution Analysis Type analysis Options
Slide 15
-
7/28/2019 3-D modal Analysis lecture 10.pdf
16/23
Slide 16
-
7/28/2019 3-D modal Analysis lecture 10.pdf
17/23
18. Solve the problem
Main Menu: Solution Solve Current LSa. Click OK on the Solve Current Load Step window
b. Close the /STATUS Command window
c. Close the Solution is done! window
22. Check any warnings or error messages
y enu: e s rror e
Slide 17
-
7/28/2019 3-D modal Analysis lecture 10.pdf
18/23
Postprocessing
19. Plot the deformed shape Main Menu: General Post roc Read Results First Set
Main Menu: General Postproc Plot Results Contour Plot Nodal Solu
Slide 18
-
7/28/2019 3-D modal Analysis lecture 10.pdf
19/23
Slide 19
Mode 1, 515.043 Hz
-
7/28/2019 3-D modal Analysis lecture 10.pdf
20/23
-
7/28/2019 3-D modal Analysis lecture 10.pdf
21/23
-
7/28/2019 3-D modal Analysis lecture 10.pdf
22/23
Main Menu: General Postproc Read Results Next Set
Utility Menu: Plot Replot
Slide 22Mode 4, 6920 Hz
-
7/28/2019 3-D modal Analysis lecture 10.pdf
23/23
Main Menu: General Postproc Read Results Next Set
Utility Menu: Plot Replot
Slide 23Mode 5, 8778 Hz