24V/ 48V/ 110V SMPS CHARGER SYSTEM

* The above Parameters are subject to change without prior notice due to continuous improvement in technology.

Input Voltage : 230V (160-275V), 50 Hz, Single ph(90-300V on

request). For 3 ph input they are suitably configured

Output Voltage : 24V/48V/110V nominal

40V/65V/150V max under Boost

Output Current (Module) : 24V/75A max, 48V/25A max, and 110V/20A max

(However they are paralleled in N+1)0 0Ambient : -10 C to +70 C Max

Attitude : upto 1000 meter above MSL

Input line PF : >0.99 Lag

Input Current Dist : <5% THD.

Efficiency : >90%.

TECHNICAL SPECIFICATION

The monitoring & control module continuously monitors

input supply as well as Battery path DC Voltage & current and gives

suitable command to all modules operating in parallel. It is provided

with following features:-

Temp compensation for VRLA Battery

Battery Health Monitoring

Dropper Diode Selection

Lightning and surge protection at rack level.

The total charger system as per the user's need, can be supplied in various configurations like

stand alone float cum boost charger, dual redundant, master slave etc. For 48V System, even

natural cooled systems are also available.

For smaller capacity systems using maintenance free Batteries, systems with battery housed in

same / identical panel are also available on demand.

SEIL also offers complete power supply system with single Battery but multiple output

DC & AC Voltages using SEIL's DC - DC Converter & Inverter modules.

Typical charger configuration being used are shown below:

Statcon Electronics with more than 2 decades of experience in

design and supply of Battery Chargers, has developed SMPS

Technology. More than 12,000 such modules are already working

in Indian environmental conditions. SMPS Technology has many

advantages over the

conventional SCR Controlled Technology like redundancy,

modular construction, high efficiency, low input line current

harmonics, high input line power factor etc.

Each SMPS Module strictly meets following technical parameters:-

Automatic Float / Boost Changeover

Constant Current/Constant Voltage Charging of Battery

Output voltage settings for VRLA/Lead Acid / Ni-cd Battery

A-34, Sector-59, Noida, G.B.Nagar - 201301

Ph.: +91-120-3356101 Fax: +91-120-3356121E-mail:info@sindia .co.in, Web: www.sindia.co.in

NOTE : SCHEMATIC DRAWING SHOWING STAND-ALONE AS WELL AS DUAL REDUNDANT SYSTEM

COUPLER

FEEDERS

LOAD BUS

DROPPER DIODESBATTERY BUS

SMR SMR SMR INT

EL

LIG

EN

T

LIGHTING & SURGE

~=

~=

~=

~ ~MAINS 1

BA

TT

ER

Y

MAINS 2

AC BUS

PROTECTION

MO

NIT

OR

MO

NIT

OR

ING

INS

UL

AT

ION

MO

NIT

OR

FE

ED

ER

EA

RT

H

FEEDERS

LOAD BUS

DROPPER DIODESBATTERY BUS

SMR SMR SMR INT

EL

LIG

EN

T

LIGHTING & SURGE

~=

~=

~=

~ ~MAINS 1

BA

TT

ER

Y

MAINS 2

AC BUS

PROTECTION

MO

NIT

OR

MO

NIT

OR

ING

INS

UL

AT

ION

MO

NIT

OR

FE

ED

ER

EA

RT

H

SMPS CHARGER WITH 25A MODULES SMPS CHARGER WITH 12.5A MODULES

24V/ 48V/ 110V SMPS CHARGER SYSTEM

* The above Parameters are subject to change without prior notice due to continuous improvement in technology.

Input Voltage : 230V (160-275V), 50 Hz, Single ph(90-300V on

request). For 3 ph input they are suitably configured

Output Voltage : 24V/48V/110V nominal

40V/65V/150V max under Boost

Output Current (Module) : 24V/75A max, 48V/25A max, and 110V/20A max

(However they are paralleled in N+1)0 0Ambient : -10 C to +70 C Max

Attitude : upto 1000 meter above MSL

Input line PF : >0.99 Lag

Input Current Dist : <5% THD.

Efficiency : >90%.

TECHNICAL SPECIFICATION

The monitoring & control module continuously monitors

input supply as well as Battery path DC Voltage & current and gives

suitable command to all modules operating in parallel. It is provided

with following features:-

Temp compensation for VRLA Battery

Battery Health Monitoring

Dropper Diode Selection

Lightning and surge protection at rack level.

The total charger system as per the user's need, can be supplied in various configurations like

stand alone float cum boost charger, dual redundant, master slave etc. For 48V System, even

natural cooled systems are also available.

For smaller capacity systems using maintenance free Batteries, systems with battery housed in

same / identical panel are also available on demand.

SEIL also offers complete power supply system with single Battery but multiple output

DC & AC Voltages using SEIL's DC - DC Converter & Inverter modules.

Typical charger configuration being used are shown below:

Statcon Electronics with more than 2 decades of experience in

design and supply of Battery Chargers, has developed SMPS

Technology. More than 12,000 such modules are already working

in Indian environmental conditions. SMPS Technology has many

advantages over the

conventional SCR Controlled Technology like redundancy,

modular construction, high efficiency, low input line current

harmonics, high input line power factor etc.

Each SMPS Module strictly meets following technical parameters:-

Automatic Float / Boost Changeover

Constant Current/Constant Voltage Charging of Battery

Output voltage settings for VRLA/Lead Acid / Ni-cd Battery

A-34, Sector-59, Noida, G.B.Nagar - 201301

Ph.: +91-120-3356101 Fax: +91-120-3356121E-mail:info@sindia .co.in, Web: www.sindia.co.in

NOTE : SCHEMATIC DRAWING SHOWING STAND-ALONE AS WELL AS DUAL REDUNDANT SYSTEM

COUPLER

FEEDERS

LOAD BUS

DROPPER DIODESBATTERY BUS

SMR SMR SMR INT

EL

LIG

EN

T

LIGHTING & SURGE

~=

~=

~=

~ ~MAINS 1

BA

TT

ER

Y

MAINS 2

AC BUS

PROTECTION

MO

NIT

OR

MO

NIT

OR

ING

INS

UL

AT

ION

MO

NIT

OR

FE

ED

ER

EA

RT

H

FEEDERS

LOAD BUS

DROPPER DIODESBATTERY BUS

SMR SMR SMR INT

EL

LIG

EN

T

LIGHTING & SURGE

~=

~=

~=

~ ~MAINS 1

BA

TT

ER

Y

MAINS 2

AC BUS

PROTECTION

MO

NIT

OR

MO

NIT

OR

ING

INS

UL

AT

ION

MO

NIT

OR

FE

ED

ER

EA

RT

H

SMPS CHARGER WITH 25A MODULES SMPS CHARGER WITH 12.5A MODULES