24 channel analogue ic tester module - abi electronics sol plus datasheet.pdf24 channel analogue ic...
TRANSCRIPT
Other specificationsElectrical input: (typical) +12 V, 1 A (max)
(typical) -5 V, 750 mA(typical) -12 V, 100 mA
Dimensions: 147 x 202 x 42 mmWeight: 1 kg
AccessoriesStandard 1 x SMD test tweezer set and adapters
1 x 24 way test clip and cable assembly1 x Blue V-I probes and adapter1 x Yellow V-I probes and adapter2 x Pulse leads2 x Ground leads3 x Discrete leads
OptionsInternal fitting PCI interfaceExternal fitting MultiLink case (cost option) with serial or
parallel connectionExternal case (cost option) which can hold up to 4 SYSTEM 8 modules.
The ABI development team strive continually to improve their products for the benefit of the customer. The specification of current products may therefore vary from that described in this brochure.
V-I test capabilityNumber of test channels: 24 + 2 probes and referencesTest voltage: 2 V to 50 V peak to peakVoltage resolution: 8 to 12 bitsTest frequency: 37.5 Hz to 12 kHzTest current: 1 µA to 150 mASource impedance: 100 Ohm to 1 MTest waveforms: Sine, square, triangle, ramp, pulseWaveform modes: V-I, V-T, I-TWaveform display: Multi-plot with single waveform zoomWaveform comparison: Automatic comparison algorithm for good
and bad boards using live probes or diskV-I comparison tolerance: 50 mV to 500 mV with 50 mV resolutionPackage support: DIL, SOIC, PLCC, QFP and variants with
MultiProbesPulse output: Positive, negative or bipolar for thyristors/
triacsPulse amplitude: Adjustable to +/-10 VCalibration: Can be calibrated by user
Analogue functional test capabilityNumber of I/O channels: 24 independent + 3 special discrete
channelsDriver voltage: -12 V to +12 VDriver voltage resolution: 10 bitDriver output current: 200 mA max sink or sourceDriver states: Voltage source, current source, offDiscrete source current: 10 µA - 150 mA. (driving a load returned to 0
V)Driver source impedance: 34 Ohm (34 Ohm, 1 k or 10 k on discrete
channels)Sensor input voltage: +/- 24 VSensor voltage protection: +/- 50 VSensor input impedance: 2 MSensor voltage resolution: 12 bitRestrict voltage: -10 V to +10 VRestrict voltage resolution: 8 bitSensor current measurement: 1 mA to 150 mA (10 nA to 150 mA on discrete
channels)Sensor current resolution: 12 bitSensor current input impedance: 50 Ohm (50 Ohm, 1 k, 10 k or 1 M
on discrete channels)Short detection threshold: <4 OhmLink detection threshold: <10 OhmTest modes: Single, unconditional loop, pass loop, fail
loopTest clip positioning: Automatically adjusts for clip orientationCircuit compensation: Automatically modifies test for IC/PCB
connectionsTest trace: Test waveforms and voltages displayedTest analysis: Displays test parameters such as gain, hfe,
feedbackIC test capability: Op-amps, comparators, DACs, ADCs,
switches and special function analogue ICs in-circuit.
Discrete test capability: Transistors, FETs, thyristors, triacs in- or out-of-circuit
IC test libraries: Analogue, discrete, package, userResult comparison: Results can be saved for good/bad board
comparisonPackage support: DIL, SOIC, PLCC and variants with
MultiProbe kitsSLIM test programming: Structured programming language for
library additions
24 channel Analogue IC Tester Module
ABI Electronics LtdDodworth Business Park
Barnsley S75 3SPSouth Yorkshire
United KingdomTel: +44 (0) 1226 207420
Fax: +44 (0) 1226 207620www.abielectronics.co.uk
AccessoriesStandard Automatic out-of-circuit adapter
1 x 64 way test cable1 x 64 way split test cable1 x V-I probe assembly1 x BDO cable1 x Short locator cable1 x Ground clip1 x PSU lead set
OptionsInternal fitting PCI interfaceExternal fitting MultiLink case (cost option) with serial or parallel
connectionExternal case (cost option) which can hold up to 4 SYSTEM 8 modules.
The ABI development team strive continually to improve their products for the benefit of the customer. The specification of current products may therefore vary from that described in this brochure.
Digital IC test capabilityNumber of I/O channels: 64-256Number of guard outputs: 4 or 8Live comparison: 64 x 2, 128 x 2 with additional modulesDrive output voltage: TTL/CMOS compatibleDrive output current: Device dependent
Typical H-L 80mA @ 0.6VTypical L-H 200mA @ 2VMax. 400mA
Drive slew rate: >100V/µsReceive input: +/-10VInput impedance: 10kTermination: Programmable for tri-state/open collectorDrive states: Low, high, tri-stateOver voltage protection: <0.5V, >5.5VTest time: Dependent on deviceCircuit modes: In-circuit. Out-of-circuit (with adapter)
Power supply for board under testAutomatic power supply: 1 x 5V @ 5A fixed
( 2 x 5V @ 5A fixed for 128 channels)Over voltage protection: 7VShort circuit current: 7A
Test modesSingle: Single testLoop: Unconditional, loop while good, loop while badAuto: Find tightest valid thresholds
Test thresholdsResolution: 100mVLow levels: TTL 0.1V to 1.1V
CMOS 0.1V to 1.5VSwitching levels: TTL 1.0V to 2.3V
CMOS 1.0V to 3.0VHigh levels: TTL 1.9V to 4.9V
CMOS 1.9V to 4.9VSwept low levels: TTL 0.1V to 1.1V
CMOS 0.1V to 1.5VSwept switching levels: TTL 1.2V
CMOS 2.5VSwept high levels: TTL 1.9V to 4.9V
CMOS 1.9V to 4.9V
Test typesTruth table (functional): Library based functional testConnections (MDA): Short circuit detection
Floating input detectionOpen circuit detectionLinked pin detection
Voltage: Resolution 10mVRange +/-10VLogic state detection
VI: Number of channels 64 - 256Sweep ranges -10V to +10V(programmable)Maximum test current 1mAMulti-plot with single waveform zoom
Thermal: Indication of pin temperature
Test librariesLibrary classes: TTL 54/74 logic, CMOS, Memory, Interface, LSI,
Microprocessor, PAL/EPLD, Linear, Package, Special and user defined
Package types: DIL, SOIC, PLCC, QFP
64 channel Board Fault Locator Module
ABI Electronics LtdDodworth Business Park
Barnsley S75 3SPSouth Yorkshire
United KingdomTel: +44 (0) 1226 207420
Fax: +44 (0) 1226 207620www.abielectronics.co.uk
Logic SupplyLow voltage output for digital circuitsVoltage 2.5V to 6V programmableResolution 0.01VOver voltage 3V to 7V programmable thresholdResolution 0.1VCurrent 5AShort circuit current 7AShort circuit duration indefinite (auto recovery)Load regulation 0.5% (20% to 80% load change)Ripple voltage 80mV pk-pk max
Variable Positive SupplyPositive voltage output for analogue circuitsVoltage 0 to +24V programmableResolution 0.01VCurrent 1.5A maxOver current limit 50mA to 1.5A programmable thresholdShort circuit current 1.5AShort circuit duration indefinite (auto recovery)Load regulation 0.1% (20% to 80% load change)Ripple voltage 50mV pk-pk maxVariable Negative SupplyNegative voltage output for analogue circuitsVoltage 0 to -24V programmableResolution 0.01VCurrent 1.5A maxOver current limit 50mA to 1.5A programmable thresholdShort circuit current 1.5AShort circuit duration indefinite (auto recovery)Load regulation 0.1% (20% to 80% load change)Ripple voltage 50mV pk-pk max
Physical dataWeight 5kgSize 295 x 247 x 65mmPower rating 150W maxConnectors and cables power cable, parallel interface cable, logic
and ground cables, +V and -V cablesPC requirements (Minimum) System capable of running
Windows 95/98 with at least 32MB of RAM and 20MB of free hard disk spaceECP/EPP capable parallel port or 16550 serial port
The ABI development team strive continually to improve their products for the benefit of the customer. The specification of current products may therefore vary from that described in this brochure.
Variable Power Supply Module
ABI Electronics LtdDodworth Business Park
Barnsley S75 3SPSouth Yorkshire
United KingdomTel: +44 (0) 1226 207420
Fax: +44 (0) 1226 207620www.abielectronics.co.uk