224100 fl.residential plumbing fixtures.gerber plumbing fixtures

7/29/2019 224100 FL.residential Plumbing Fixtures.gerber Plumbing Fixtures

1/45

Copyright 2009 AIA MasterSpec Full Length 09/09

PRODUCT MASTERSPEC LICENSED BY ARCOM TO GERBER PLUMBING FIXTURES LLC

Copyright 2009 by The American Institute of Architects (AIA)

Exclusively published and distributed by Architectural Computer Services, Inc. (ARCOM) for the AIA

This Product MasterSpec Section is licensed by ARCOM to Gerber Plumbing Fixtures LLC ("

("Licensee").

This Product MasterSpec Section modifies the original MasterSpec text, and does not include the

full content of the original MasterSpec Section

Revisions made to the original MasterSpec text are made solely by the Licensee and are not endorsed by,

or representative of the opinions of, ARCOM or The American Institute of Architects (AIA). Neither

AIA nor ARCOM are liable in any way for such revisions or for the use of this Product MasterSpec

Section by any end user. A qualified design professional should review and edit the document to suit

project requirements.

For more information, contact Gerber Plumbing Fixtures LLC, 2500 Internationale Parkway; Woodridge,

IL 60517 phone: 630-754-0268; fax: 630-783-9003; Website: www.gerberonline.com; e-mail:[email protected].

For information about MasterSpec contact ARCOM at (800) 424-5080 or visit www.MasterSpec.com.

SECTION 224100 - RESIDENTIAL PLUMBING FIXTURES

Revise this Section by deleting and inserting text to meet Project-specific requirements.

Verify that Section titles referenced in this Section are correct for this Project's Specifications; Section

titles may have changed.

PART 1 - GENERAL

1.1 RELATED DOCUMENTS

Retain or delete this article in all Sections of Project Manual.

A. Drawings and general provisions of the Contract, including General and Supplementary

Conditions and Division 01 Specification Sections, apply to this Section.

1.2 SUMMARY

Adjust list below to suit Project. Not all products included in the list below are manufactured or provided

by Gerber Plumbing Fixtures LLC.

A. Section Includes:

1. Bathtubs.

2. Faucets.

RESIDENTIAL PLUMBING FIXTURES 224100 - 1


2/45



3. Whirlpool baths.

4. Walk-in baths.

5. Bidets.

6. Lavatories.

7. Showers.8. Bar sinks.

9. Kitchen sinks.10. Laundry trays.

11. Dishwasher air-gap fittings.

12. Laminar-flow, faucet-spout outlets.

13. Disposers.

14. Hot-water dispensers.

15. Water closets.

16. Toilet seats.

17. Supply fittings.

18. Waste fittings.

B. Related Requirements:

Retain subparagraphs below to cross-reference requirements Contractor might expect to find in this

Section but are specified in other Sections.

1. Division 22 Section "Commercial Water Closets."

2. Division 22 Section "Commercial Urinals."

3. Division 22 Section "Commercial Lavatories."

4. Division 22 Section "Commercial Sinks."

5. Division 22 Section "Commercial Showers, Receptors, and Basins."

6. Division 22 Section "Healthcare Plumbing Fixtures."

7. Division 22 Section "Emergency Plumbing Fixtures."

8. Division 22 Section "Security Plumbing Fixtures."

9. Division 22 Section "Drinking Fountains and Water Coolers."

1.3 ACTION SUBMITTALS

A. Product Data: For each type of product.

1. Include construction details, material descriptions, dimensions of individual components

and profiles, and finishes for lavatories.

2. Include rated capacities, operating characteristics, electrical characteristics, and furnished

specialties and accessories.

B. LEED Submittals:

Retain "Product Data for Prerequisite WE 1 ( and Credit WE 3) (, Credit WE 2, and Credit WE 3)"

Subparagraph below for LEED-NC, LEED-CS, and LEED for Schools for fixtures and equipment thatconsume water.

1. Product Data for Prerequisite WE 1[ and Credit WE 3] [, Credit WE 2, and

Credit WE 3]: Documentation indicating flow and water consumption requirements.



3/45



Retain "Product Data for Prerequisite WE 1" Subparagraph below for LEED-CI for fixtures and

equipment that consume water.

2. Product Data for Prerequisite WE 1: Documentation indicating flow and waterconsumption requirements.

Retain "Product Data for Prerequisite WE 1( and Credit WE 2)" Subparagraph below for LEED-EB forfixtures and equipment that consume water.

3. Product Data for Prerequisite WE 1[ and Credit WE 2]: Documentation indicating flow

and water consumption requirements.

Retain "Shop Drawings" Paragraph below if equipment includes wiring.

C. Shop Drawings: Include diagrams for power, signal, and control wiring.

D. Lead Free: Manufacturer's statement of compliance with requirements of California Assembly

Bill AB 1953.

E. Water Efficiency: Manufacturer's statement of compliance with requirements of EPA

WaterSense program.

1.4 INFORMATIONAL SUBMITTALS

Retain "Coordination Drawings" Paragraph below if coordination is required for installation of products

and materials by separate installers.

A. Coordination Drawings: Counter cutout templates for mounting of counter-mounted plumbing

fixtures.

B. Sample Warranty: For special warranty.

1.5 CLOSEOUT SUBMITTALS

A. Operation and Maintenance Data: For plumbing fixtures and faucets to include in emergency,

operation, and operation and maintenance manuals.

Retain subparagraph below if whirlpool baths or walk-in baths are required for Project.

1. In addition to items specified in Division 01 Section "Operation and Maintenance Data,"

include the following:

a. Servicing and adjustments of [whirlpool baths] [and] [walk-in baths].

1.6 MAINTENANCE MATERIAL SUBMITTALS

A. Furnish extra materials that match products installed and that are packaged with protective

covering for storage and identified with labels describing contents.



4/45



1. Faucet Washers and O-Rings: Equal to [10] percent of amount of

each type and size installed.

2. Faucet Cartridges and O-Rings: Equal to [5] percent of amount of

each type and size installed.

3. Flushometer-Tank Repair Kits: Equal to [5] percent of amount ofeach type installed, but no fewer than [two] of each type.

4. Toilet Seats: Equal to [5] percent of amount of each type installed.

1.7 WARRANTY

When warranties are required, verify with Owner's counsel that warranties stated in this article are not

less than remedies available to Owner under prevailing local laws.

A. Special Warranty: Manufacturer agrees to repair or replace components of [walk-in baths][and] [whirlpool baths] that fail in materials or workmanship within specified warranty period.

1. Failures include, but are not limited to, the following:

a. Structural failures of unit shell.

b. Faulty operation of controls, blowers, pumps, heaters, and timers.

c. Deterioration of metals, metal finishes, and other materials beyond normal use.

Verify available warranties and warranty periods for units and components.

2. Warranty Period for Residential Applications of Shells: [Five] [20] [30] years from date of Substantial Completion.

3. Warranty Period for Residential Applications of Pumps and Blowers: [Five] [20]

years from date of Substantial Completion.4. Warranty Period for Commercial Applications of Electronic Controls: Five years from

date of Substantial Completion.

PART 2 - PRODUCTS

See Editing Instruction No. 1 in the Evaluations for cautions about named manufacturers and products.

For an explanation of options and Contractor's product selection procedures, see Division 01 Section

"Product Requirements."

2.1 BATHTUBS

Copy "Bathtubs" Paragraph below and re-edit for each type of bathtub required.

Insert number to complete drawing designation. Use these designations on Drawings to identify each

bathtub.

A. Bathtubs : [Enameled cast iron] [Enameled steel] [FRP]

[PMMA], with shower.



5/45



Retain "Manufacturers" Subparagraph and list of manufacturers below to require products from

manufacturers listed or a comparable product from other manufacturers.

1. Manufacturers: Subject to compliance with requirements, [provide products by the

following] [provide products by one of the following] [available manufacturers

offering products that may be incorporated into the Work include, but are not

limited to, the following]:

Retain "Basis-of-Design Product" Subparagraph and list of manufacturers below to identify a specific

product or a comparable product from manufacturers listed. Retain option and delete insert note if

manufacturer's name and model number are indicated on Drawings.

2. Basis-of-Design Product: Subject to compliance with requirements, provide [product

indicated on Drawings] .

First list of manufacturers below is for enameled-steel bathtubs.

c. American Standard America.

d. Bootz Industries.

e. Briggs Plumbing Products, Inc.

f. Crane Plumbing, L.L.C.

g. Eljer, Inc.

h. .

List of manufacturers below is for PMMA (acrylic) bathtubs.

o. Acryline USA, Inc.

p. American Standard America.

q. Aqua Bath Company, Inc.

r. Aqua Glass Corporation.

s. Aquatic Industries, Inc.

t. Clarion Bathware.

u. Crane Plumbing, L.L.C.

v. Florestone Products Co., Inc.

w. Kohler Co.

x. Lyons Industries, Inc.



6/45



y. Mansfield Plumbing Products LLC; Acrylic Division.

z. Praxis Industries, LLC; Aquarius Bathware.

aa. St. Thomas Creations.

bb. Swan Corporation (The).

cc.


7/45



1. Basis-of-Design Product: Subject to compliance with requirements, provide Gerber

Plumbing Fixtures LLC; [Allerton] [Brianne] [Abigail] [Logan Square] [Wicker

Park] [Riverdale] [Waveland], or comparable product by one of the following:

Retain one of two lists of manufacturers below. First list is for pressure-balance faucets.

a. American Standard America.b. Danze, Inc.

c. Kohler Co.

d. Moen Incorporated.

e. Symmons Industries, Inc.

f. .

2. Standards: ASME A112.18.1/CSA B125.1 and ASSE 1016.3. Faucet:

a. Body Material: Solid brass.

b. Finish: Polished chrome plate.

c. Maximum Flow Rate: [2.5 gpm (9.5 L/min.)] unless otherwise

indicated.

d. Mounting: [Concealed] [Exposed].

e. Operation: Single handle, [push-pull] [or] [twist or rotate] control, with hot- and

cold-water indicators.

f. Antiscald Device: [Integral with mixing valve] [Separate unit] [Not required].

g. Check Stops: Check-valve type, integral with or attached to body; on hot- and

cold-water supply connections.h. Diverter: In-tub filler spout.

i. Supply Connections: NPS 1/2 (DN 15).

4. Shower Head:

a. Standard: ASME A112.18.1/CSA B125.1.

b. Type: [Ball joint with arm and flange] [Without ball joint, but with arm and

flange] [Ball joint and head integral with mounting flange] [Integral with

mounting flange] [Hand shower. Include wall-mounting device] .

Retain "Backflow-Prevention Device" Subparagraph below with hand-shower type.

c. Backflow-Prevention Device: ASSE 1014.d. Shower Head Material: Metallic with chrome-plated finish.

e. Spray Pattern: [Center-jet flow control] [Adjustable] [Fixed].

f. Integral Volume Control: [Not required] [Required].

Retain "Shower-Arm, Flow-Control Fitting" Subparagraph below only if retaining option that includes

arm and flange in "Type" Subparagraph above.



8/45



g. Shower-Arm, Flow-Control Fitting: [Not required] [1.5 gpm (5.7 L/min.)] [2.0

gpm (7.6 L/min.)].

Verify availability of feature in "Temperature Indicator" Subparagraph below if required.

h. Temperature Indicator: [Integral with faucet] [Not required].

5. Bathtub Filler Spout: Chrome-plated brass.

2.3 WHIRLPOOL BATHS

Whirlpool baths in this article are usually the drop-in-type mounted in a base unit. Some units arefreestanding with a front apron. Both types require access to equipment.

Copy "Whirlpool Baths" Paragraph below and re-edit for each type of hydromassage bathtub required.


hydromassage bathtub. Do not use same designation as is used for another hydromassage bathtub in otherDivision 22 plumbing-fixture Sections. See Specification Coordination Checklist for other Sections

specifying hydromassage bathtubs.

A. Whirlpool Baths : [Enameled cast-iron] [Enameled-steel]

[FRP] [PMMA] hydromassage bathtub.












First list of manufacturers below is for enameled-steel whirlpool baths.

c. American Standard America.

d. Mansfield Plumbing Products LLC.

e.


9/45



First list of manufacturers below is for FRP whirlpool baths.

f. Best Bath Systems.

g. Clarion Bathware.h. MAAX.

i. MAAX; Aker Division.

j. Praxis Industries, LLC; Aquarius Bathware.k. Sterling; a Kohler company.

l. .

Retain one of two "Standards" subparagraphs below.

3. Standards: ASME A112.19.1/CSA B45.2 and UL 1795 for enameled [cast-iron] [-steel]

hydromassage bathtubs.

4. Standards: ANSI Z124.1.2 and UL 1795 for [FRP] [PMMA] hydromassage bathtubs.

5. General: Bathtub with air-entrained, water-jet nozzles and water circulation.

6. Fixture:

a. Seating Capacity: [One] [Two] person(s).

b. Bathing Surface: Slip resistant according to ASTM F 462.

c. Size: [60 by 30 inches (1525 by 762 mm)] [66 by 30 inches (1680 by 762 mm)]

[60 by 42 inches (1525 by 1065 mm)] .

d. Nominal Water Capacity: .e. Apron: Matching unit, covering exposed front and sides, and with access panel.

f. Color: [White] .



10/45



g. Drain Location: [Left] [Right] end.

Insert specific controls required for "Controls" Subparagraph below.

h. Controls: For pump[, timer,] [and water heater].

7. Faucet:

a. NSF Standard: Comply with NSF/ANSI 61, "Drinking Water System Components

- Health Effects," for faucet materials that will be in contact with potable water.

b. Description: Fixture manufacturer's chrome-plated, solid-brass [individual

valves] [mixing valve] with over-rim tub filler.

c. Faucet Standard: ASME A112.18.1/CSA B125.1.

8. Supplies: NPS 1/2 (DN 15) copper tubing with ball, gate, or globe valves.

9. Waste Fittings:

a. Standard: ASME A112.18.2/CSA B45.125.2.

b. Size: NPS 1-1/2 (DN 40).c. Drain: Chrome-plated exposed parts; brass pop-up waste and overflow.

Retain one of two "Drain Piping" subparagraphs below.

d. Drain Piping: Cast- and tubular-brass overflow, P-trap, and waste.

e. Drain Piping: Schedule 40 [ABS] [or] [PVC], overflow, P-trap, and waste.

10. Water-Circulating System: Electric circulating pump complying with ASME A112.19.7

and with UL 1951, and listed and labeled as defined in NFPA 70, by a qualified testingagency, and marked for intended location and application and plastic piping.

"Water Heater" Subparagraph below is a useful, but unnecessary, feature.

11. Water Heater: Electric, inline complying with UL 1951, and listed and labeled as defined

in NFPA 70, by a qualified testing agency, and marked for intended location and

application.

12. Unit Electrical Characteristics:

a. Volts: [120] [240] [277] [480] .

b. Phase(s): [Single] [Three].c. Hertz: [60] .

d. Full-Load Amperes: .

e. Minimum Circuit Ampacity: .

f. Maximum Overcurrent Protection: .

Copy "Whirlpool Baths" Paragraph below and re-edit for each type of PMMA air-massage bathtub

required.

Insert number to complete drawing designation. Use these designations on Drawings to identify each air-

massage bathtub. Do not use same designation as is used for another air-massage bathtub in other

Division 22 plumbing-fixture Sections. See Specification Coordination Checklist for other Sections

specifying air-massage bathtub.



11/45



B. Whirlpool Baths : PMMA air-massage bathtub.




following] [provide products by one of the following] [available manufacturersoffering products that may be incorporated into the Work include, but are not







3. Standards: ANSI Z124.1.2 and UL 1795.

4. General: Air-massage bathtub with air-injection nozzles.5. Fixture:

a. Seating Capacity: [One] [Two] person(s).

b. Bathing Surface: Slip resistant according to ASTM F 462.

c. Size: [60 by 30 inches (1525 by 762 mm)] [66 by 30 inches (1680 by 762 mm)]

[60 by 42 inches (1525 by 1065 mm)] .

d. Nominal Water Capacity: .

e. Apron: Matching unit, covering exposed front and sides, and with access panel.

f. Color: [White] .

g. Drain Location: [Left] [Right] end.

Insert specific controls required for "Controls" Subparagraph below.

6. Controls: For blower[, timer,] [and water heater].

7. Faucet:




valves] [mixing valve] with over-rim tub filler.



12/45





9. Waste Fittings:


b. Size: NPS 1-1/2 (DN 40).c. Drain: Chrome-plated exposed parts; brass pop-up waste and overflow.




10. Water-Circulating System: Electric circulating pump, complying with ASME A112.19.7

and with UL 1951, and listed and labeled as defined in NFPA 70, by a qualified testing

agency, and marked for intended location and application and plastic piping.

"Water Heater" Subparagraph below is a useful, but unnecessary, feature.

11. Water Heater: Electric, inline complying with UL 1951, and listed and labeled as defined

in NFPA 70, by a qualified testing agency, and marked for intended location and

application.


a. Volts: [120] [240] [277] [480] .

b. Phase(s): [Single] [Three].

c. Hertz: [60] .

d. Full-Load Amperes: .e. Minimum Circuit Ampacity: .


13. Air-Injection System: Electric, [blower] [combination blower/heater] complying with

ASME A112.19.7 and with UL 1951, and listed and labeled as defined in NFPA 70, by a

qualified testing agency, and marked for intended location and application and plastic

piping.


a. Volts: [120] [240] [277] [480] .


c. Hertz: [60] .d. Full-Load Amperes: .



2.4 WALK-IN BATHS

Copy "Walk-in Baths" Paragraph below and re-edit for each type of standard, plastic, walk-in bath

required.



13/45




walk-in bath.

A. Walk-in Baths : Standard, plastic, with side-entry door, seat,and faucet.

Retain "Manufacturers" Subparagraph and list of manufacturers below to require products frommanufacturers listed or a comparable product from other manufacturers.





Retain "Basis-of-Design Product" Subparagraph and list of manufacturers below to identify a specificproduct or a comparable product from manufacturers listed. Retain option and delete insert note if


2. Basis-of-Design Product: Subject to compliance with requirements, provide [productindicated on Drawings] .

3. Fixture:

a. Standards: ANSI Z124.1.2.

b. Material: [Plastic] [PMMA] .

c. Nominal Size: Approximately 60 by 32 by 21 inches (1525 by 815 by 535 mm).

d. Skirt: [Front only] [On sides not against walls].

e. Seat: Integral.

f. Grab Bar: Manufacturer's standard.

g. Door: Side opening with rubber sealing gasket.

h. Door Location: [Left] [Right] side.i. Drain Location: [Left] [Right] end.

4. Faucet:





14/45




valves] [mixing valve] with over-rim tub filler.[ Include diverter and hand

shower.]


d. Mounting: Deck.

5. Supplies: NPS 1/2 (DN 15) copper tubing with ball, gate, or globe valves.6. Waste Fittings:


b. Size: NPS 1-1/2 (DN 40).

c. Drain: Chrome-plated exposed parts; brass pop-up waste and overflow.




f. Drain Piping: [Yellow] [Red] brass.

7. Water-Circulating System: Electric circulating pump complying with ASME A112.19.7

and with UL 1951, and listed and labeled as defined in NFPA 70, by a qualified testing



a. Volts: [120] [240] [277] [480] .


c. Hertz: [60] .




Copy "Walk-in Baths" Paragraph below and re-edit for each type of plastic, hydromassage, walk-in bath

required.


walk-in bath.

B. Walk-in Baths : Plastic, hydromassage, with side-entry door,

seat, and faucet.











15/45





3. Fixture:

a. Standards: ANSI Z124.1.2 and UL 1795.

b. Nominal Size: Approximately 60 by 32 by 21 inches (1525 by 815 by 535 mm).

c. Skirt: [Front only] [On sides not against walls].d. Seat: Integral.

e. Grab Bar: Manufacturer's standard.

f. Door: Side opening with rubber sealing gasket.g. Door Location: [Left] [Right] side.h. Drain Location: [Left] [Right] end.

4. Faucet:




valves] [mixing valve] with over-rim tub filler.[ Include diverter and hand

shower.]


d. Mounting: Deck.


6. Waste Fittings:


b. Size: NPS 1-1/2 (DN 40).

c. Drain: Chrome-plated exposed parts; brass pop-up waste and overflow.


d. Drain Piping: Cast- and tubular-brass overflow, P-trap, and waste.e. Drain Piping: Schedule 40 [ABS] [or] [PVC], overflow, P-trap, and waste.

7. Water-Circulating System: Electric circulating pump complying with ASME A112.19.7and with UL 1951, and listed and labeled as defined in NFPA 70, by a qualified testing



a. Volts: [120] [240] [277] [480] .




16/45



c. Hertz: [60] .




2.5 BIDETS

Copy "Bidets" Paragraph below and re-edit for each type of bidet required.


bidet.

A. Bidets :1. Basis-of-Design Product: Subject to compliance with requirements, provide Gerber

Plumbing Fixtures LLC; Aquasaver, or comparable product by one of the following:

a. American Standard America.

b. Danze, Inc.c. Duravit USA, Inc.

d. Kohler Co.

e.


17/45




lavatory. Do not use same designation as is used for another lavatory in other Division 22 plumbing-

fixture Sections. See Specification Coordination Checklist for other Sections specifying lavatories.

A. Lavatories : [Oval] [Rectangular], vitreous china, counter

mounted.

In "Basis-of-Design Product" Subparagraph below retain "Wicker Park" or "Logan Square" for

rectangular lavatories; and retain "Brianne," "Allerton," "Maxwell," "Riverdale," or "Abigail" for oval

lavatories.


Plumbing Fixtures LLC; [Wicker Park] [Logan Square] [Brianne] [Allerton]

[Maxwell] [Riverdale] [Abigail], or comparable product by one of the following:

First list of manufacturers below is for enameled-steel lavatories.


b. Eljer, Inc.

c. .

List of manufacturers below is for vitreous-china lavatories.

h. American Standard America.

i. Duravit USA, Inc.j. TOTO USA, INC.

k.


18/45



h. Rectangular Nominal Size: [18 by 15 inches (457 by 381 mm)] [19 by 16 inches

(483 by 406 mm)] [20 by 18 inches (508 by 457 mm)] [24 by 20 inches (610 by

508 mm)] .

i. Round Nominal Size: [18 inches (457 mm)] [19 inches (483 mm)] in diameter.j. Faucet-Hole Punching: [One hole] [Three holes, 2-inch (51-mm) centers]

[Three holes, 4-inch (102-mm) centers].k. Faucet-Hole Location: [None] [Rim].

l. Color: [Not applicable] [White] .

3. Faucet: .

4. Supply Fittings: Comply with requirements in "Supply Fittings" Article.

5. Waste Fittings: Comply with requirements in "Waste Fittings" Article.

Copy "Lavatories" Paragraph below and re-edit for each type of vitreous-china, pedestal lavatory

required.


lavatory. Do not use same designation as is used for another lavatory in other Division 22 plumbing-fixture Sections. See Specification Coordination Checklist for other Sections specifying lavatories.

B. Lavatories : [Oval] [Rectangular], vitreous china, pedestal.

In "Basis-of-Design Product" Subparagraph below, retain "Wicker Park" or "Logan Square" for

rectangular lavatories or "Brianne," "Picureesque," "Allerton," or "Maxwell" for oval lavatories.


Plumbing Fixtures LLC; [Wicker Park] [Logan Square] [Brianne] [Picturesque]

[Allerton] [Maxwell], or comparable product by one of the following:


b. Barclay Products Limited.c. Kohler Co.

d. TOTO USA, INC.

e.


19/45



3. Faucet: .



Copy "Lavatories" Paragraph below and re-edit for each type of oval, integral-bowl countertop lavatory

required.


lavatory. Do not use same designation as is used for another lavatory in other Division 22 plumbing-

fixture Sections. See Specification Coordination Checklist for other Sections specifying lavatories.

C. Lavatories : Oval, [cultured marble,] [solid surface,] integral

bowl countertop.










List of manufacturers below is for solid-surface countertop lavatories.

h. Aristech Surfaces; a product group of Aristech Acrylics LLC.

i. DuPont; DuPont Surfaces.

j. Formica Corporation; a Fletcher Building Limited company.

k. InPro Corporation.

l. Swan Corporation (The).

m. Wilsonart International.



20/45



n. .

List of manufacturers below is for general-duty, copper- or brass-underbody faucets.



21/45



j. American Standard America.

k. Delta Faucet Company.

l.


22/45








List of manufacturers below is for PMMA (acrylic) showers.

k. Acryline USA, Inc.

l. Aqua Bath Company, Inc.

m. Aqua Glass Corporation.

n. Aquatic Industries, Inc.

o. Clarion Bathware.

p. Crane Plumbing, L.L.C.

q. Jacuzzi, Inc.

r. Kohler Co.s. LASCO Bathware.t. MAAX; Aker Division.

u. Praxis Industries, LLC; Aquarius Bathware.

v.


23/45



10. Faucet: .

a. Maximum Flow Rate: 2.2 gpm (8.3 L/min.)

Copy "Showers" Paragraph below and re-edit for each type of accessible shower required.


shower. Do not use same designation as is used for another shower in other Division 22 plumbing-fixtureSections. See Specification Coordination Checklist for other Sections specifying showers.

B. Showers : Accessible [FRP] [PMMA] with seat, grab bar, base,

and faucet.












List of manufacturers below is for PMMA showers.

e. Aqua Bath Company, Inc.

f. Aqua Glass Corporation.

g. Clarion Bathware.h. Crane Plumbing, L.L.C.

i.


24/45



Retain "Surround" Subparagraph below for PMMA (acrylic) surround.

6. Surround: One piece.

7. Bathing Surface: Slip resistant according to ASTM F 462.8. Color: [White] .

9. Drain Location: [Left side] [Center] [Right side].

10. Accessibility Options: Grab bar and bench.11. Faucet: Shower .

12. Drain: Grid,NPS 2 (DN 50).

Copy "Showers" Paragraph below and re-edit for each type of factory-fabricated cabinet shower required.


shower. Do not use same designation as is used for another shower in other Division 22 plumbing-fixture

Sections. See Specification Coordination Checklist for other Sections specifying showers.

C. Showers : Factory fabricated cabinet.









2. Basis-of-Design Product: Subject to compliance with requirements, provide [productindicated on Drawings] .

3. Size: [30 by 30 inches (762 by 762 mm)] [32 by 32 inches (815 by 815 mm)] [36 by 36

inches (915 by 915 mm)] [36 by 39 inches (915 by 990 mm)] [45 by 39 inches (1145

by 990 mm)] .

4. Material: [Steel] [Composite] [Plastic], [front] [corner] [front and rear] access.

5. Color: [Not applicable] .6. Accessibility Options: Grab bar and bench.

7. Faucet: .

8. Supplies: NPS 1/2 (DN 15) copper tubing with shutoff valves.

9. Drain: Grid,NPS 2 (DN 50).



25/45



2.9 SHOWER FAUCETS

A. NSF Standard: Comply with NSF/ANSI 61, "Drinking Water System Components - Health

Effects," for faucet materials that will be in contact with potable water.

Copy "Shower Faucets" Paragraph below and re-edit for each type of shower faucet required.

Insert number to complete drawing designation. Use these designations in shower description to identify

required shower faucet. Do not use same designation as is used for another shower faucet in other

Division 22 plumbing-fixture Sections. See Specification Coordination Checklist for other Sections

specifying shower faucets.

B. Shower Faucets : [Single handle, pressure balance, mixingvalve] [Single handle, thermostatic, mixing valve].

1. Basis-of-Design Product: Subject to compliance with requirements, provide GerberPlumbing Fixtures LLC; [Wicker Park] [Logan Square] [Brianne] [Abigail]

[Riverdale] [Allerton] [Maxwell], or comparable product by one of the following:

Retain one of three lists of manufacturers below. First list is for single-handle, pressure-balance faucets.


b. Danze, Inc.

c. Kohler Co.

d. .

List of manufacturers below is for two-handle, non-pressure-balance and non-thermostatic mixing

faucets.

g. American Standard America.

h. Danze, Inc.

i. Kohler Co.

j.


26/45



f. Mounting: [Exposed] [Concealed].

g. Backflow-Prevention Device for Hand-Held Shower: [Required] [Not required].

h. Operation: [Compression, manual] [Noncompression, manual].

i. Antiscald Device: [Integral with mixing valve] [Separate unit] [Not required].

j. Check Stops: Check-valve type, integral with or attached to body; on hot- andcold-water supply connections.

3. Supply Connections: [NPS 1/2 (DN 15)] [NPS 3/4 (DN 20)].

4. Shower Head:

a. Type: [Ball joint] [Without ball joint] [Ball joint and head integral with

mounting flange] [Integral with mounting flange] [Hand-held, grab-bar

mounted] [Hand-held, hook mounted].

b. Shower Head Material: [Metallic] [Nonmetallic] [Combined, metallic and

nonmetallic] with chrome-plated finish.

c. Spray Pattern: [Center-jet control] [Fixed] [Adjustable].

d. Integral Volume Control: [Required] [Not required].e. Shower-Arm, Flow-Control Fitting: [Not required] [1.5 gpm (5.7 L/min.)] [1.75

gpm (6.7 L/min.)] [2.0 gpm (7.6 L/min.)].

2.10 BAR SINKS

Copy "Bar Sinks" Paragraph below and re-edit for each type of single-bowl, counter-mounted bar sink

required.

Insert number to complete drawing designation. Use these designations on Drawings to identify each bar

sink. Do not use same designation as is used for another sink in other Division 22 plumbing-fixture

Sections. See Specification Coordination Checklist for other Sections specifying bar sinks.

A. Bar Sinks : Single bowl, counter mounted, [enameled castiron] [enameled steel] [PMMA] [solid surface] [stainless steel].











indicated on Drawings]


27/45



a. Commercial Enameling Company.

b. Eljer, Inc.

c. Kohler Co.

d. .

First list of manufacturers below is for PMMA bar sinks.

k. Benjamin Mfg. Co.

Gerber Plumbing Fixtures LLC does not manufacture a product complying with requirements of thisparagraph.

l. Lyons Industries, Inc.

m. Royal Baths Manufacturing Co.

n. .

List of manufacturers below is for stainless-steel bar sinks.

w. Barclay Products Limited.

x. Elkay Manufacturing Co.

y. Franke Consumer Products, Inc.

z. Griffin Products, Inc.

aa. Houzer, Inc.bb. Just Manufacturing.

cc. Kohler Co.

dd. Moen Incorporated.

ee. Revere Sink.ff. Sterling; a Kohler company.

gg. WhiteRock Corp.

hh.


28/45



Retain one of five "Standard" subparagraphs below.

a. Standard: ASME A112.19.1/CSA B45.2 for enameled [cast-iron] [-steel]

lavatories.b. Standard: ANSI Z124.3 for PMMA lavatories.

c. Standard: ANSI Z124.3 and ANSI/ICPA SS-1 for solid-surface lavatories.

d. Standard: ASME A112.19.3/CSA B45.4 for stainless-steel lavatories.e. Standard: ASME A112.19.2/CSA B45.1 for vitreous-china lavatories.

f. Type: [Flat rim with ledge] [Self-rimming].

g. Overall Dimensions: .

h. Bowl Dimensions: .

4. Faucet: .



2.11 KITCHEN SINKS

Copy "Kitchen Sinks" Paragraph below and re-edit for each type of counter-mounted kitchen sink

required.


kitchen sink. Do not use same designation as is used for another kitchen sink in other Division 22

plumbing-fixture Sections. See Specification Coordination Checklist for other Sections specifying

kitchen sinks.

A. Kitchen Sinks : [One] [Two] [Three] bowl, counter mounted,

[enameled cast iron] [enameled steel] [PMMA] [solid surface] [stainless steel].












29/45



d. .

First list of manufacturers below is for PMMA kitchen sinks.

Gerber Plumbing Fixtures LLC does not manufacture a product complying with requirements of this

paragraph.

k. Lyons Industries, Inc.

l. .

List of manufacturers below is for stainless-steel kitchen sinks.

v. Elkay Manufacturing Co.

w. Franke Consumer Products, Inc.

x. Griffin Products, Inc.

y. Houzer, Inc.

z. Just Manufacturing.

aa. Kohler Co.

bb. Revere Sink.cc. Sterling; a Kohler company.

dd. WhiteRock Corp.

ee.


30/45



b. Standard: ANSI Z124.3 for PMMA kitchen sinks.

c. Standard: ANSI Z124.3 and ANSI/ICPA SS-1 for solid-surface kitchen sinks.

d. Standard: ASME A112.19.3/CSA B45.4 for stainless-steel kitchen sinks.

e. Overall Dimensions: .

Retain "Metal Thickness" Subparagraph below for stainless-steel sinks.

f. Metal Thickness: [0.038 inch (1.0 mm)] [0.050 inch (1.3 mm)] .

Retain "Bowl" Subparagraph below for single-bowl sinks.

g. Bowl:

1) Dimensions: .

2) Drain: 3-1/2-inch (89-mm) [crumb cup] [grid] [outlet for disposer].

a) Location: [Centered in bowl] [Near back of bowl] .

Retain "Left Bowl," "Right Bowl," and "Center Bowl" subparagraphs as required for multibowl sinks.

h. Left Bowl:

1) Dimensions: .

2) Drain: 3-1/2-inch (89-mm) [crumb cup] [grid] [grid with offset waste]

[outlet for disposer].


i. Right Bowl:

1) Dimensions: .

2) Drain: 3-1/2-inch (89-mm) [crumb cup] [grid] [grid with offset waste]

[outlet for disposer].


j. Center Bowl:

1) Dimensions: .

2) Drain: [1-1/2-inch (38-mm)] [3-1/2-inch (89-mm)] [crumb cup] [grid][grid with offset waste].

a) Location: [Centered in bowl] .

4. Faucet: .




31/45



6. Waste Fittings: Comply with requirements in "Waste Fittings" Article, except include

continuous waste for multibowl sinks.

a. Disposer: [Not required] .

b. Dishwasher Air-Gap Fitting: [Not required] [Comply with requirements in

"Dishwasher Air-Gap Fittings" Article].c. Hot-Water Dispenser: [Not required] [Comply with requirements in "Hot-

Water Dispensers" Article].

2.12 LAUNDRY TRAYS

Copy "Laundry Trays" Paragraph below and re-edit for each type of enameled cast-iron, flat-rim-ledge

and self-rimming with ledge laundry tray required.


laundry tray.

A. Laundry Trays : Enameled cast iron, [flat rim ledge] [self-

rimming with ledge].












3. Fixture:


b. Nominal Size: [24 by 21 inches (610 by 535 mm)] [24 by 23 inches (610 by 584

mm)] .

c. Color: [White] .



32/45



d. Mounting: [Freestanding on manufacturer's standard metal stand] [Flush,

counter mounted with stainless-steel ring and sealant or on-counter mounted

with sealant].

4. Faucet: .



Copy "Laundry Trays" Paragraph below and re-edit for each type of plastic laundry tray required.


laundry tray.

B. Laundry Trays : Plastic laundry tray.



1. Manufacturers: Subject to compliance with requirements, [provide products by thefollowing] [provide products by one of the following] [available manufacturers








3. Fixture:

a. Standard: IAPMO/ANSI Z124.6.

b. Style: Flat-rim ledge.

Retain "Plastic" option in "Material" Subparagraph below or retain one or more of other options if a

specific material is required.

c. Material: [Plastic] [cast polymer] [FRP] [PMMA] [or] [PP].



33/45



d. Nominal Size: [24 by 21 inches (610 by 535 mm)] [25 by 22 inches (635 by 559

mm)] .

e. Color: [White] .

f. Mounting: Freestanding on manufacturer's standard legs or separate, painted-steel

stand.

4. Faucet: .5. Supply Fittings: Comply with requirements in "Supply Fittings" Article.


2.13 SINK FAUCETS



Copy "Sink Faucets" Paragraph below and re-edit for each type of sink faucet required.

Insert number to complete drawing designation. Use these designations in sink description to identifyrequired faucet for that sink. Do not use same designation as is used for a sink faucet in other Division 22

plumbing-fixture Sections. See Specification Coordination Checklist for other Sections specifying sink

faucets.

B. Sink Faucets : [Solid brass] [Copper underbody], [kitchensink] [bar sink] [laundry tray].





[Retain one of two lists of manufacturers below. First list is for general-duty, solid-brass faucets.


b. Danze, Inc.

c. Delta Faucet Company.

d. Gerber Plumbing Fixtures LLC.

e. Hansgrohe, Inc.

f. Kohler Co.

g. .

2. Standard: ASME A112.18.1/CSA B125.1.

3. General: Include hot- and cold-water indicators; coordinate faucet inlets with supplies

and fixture holes; coordinate outlet with spout and fixture receptor.

4. Kitchen Sink Option: Separate hand spray complying with ASSE 1025.



34/45



5. Finish: [Polished chrome plate] [Polished brass] [Nonmetallic] [Polished or rough

brass] [Rough brass] .

Retain second option in "Maximum Flow Rate" Subparagraph below for laundry-tray faucets.

6. Maximum Flow Rate: [2.0 gpm (7.5 L/min.)] [2.5 gpm (9.5 L/min.)] [4.0 gpm

(15 L/min.)] unless otherwise indicated.7. Mixing Valve: [Single control] [Two-lever handle].

8. Backflow-Prevention Device for Hand Spray: [Required] [Not required].

9. Centers: [4 inches (102 mm)] [6 inches (152 mm)] [8 inches (203 mm)] [Single hole]

[Adjustable].

10. Mounting: [Deck] [Back/wall], [exposed] [concealed].

11. Handle(s): [Lever] [Knob] [Knob, nonmetallic] [Cross, four arm] [Wrist blade, 4

inches (102 mm)] [Elbow, 6 inches (152 mm)] [Not applicable].

12. Spout Type: [Rigid, solid brass] [Rigid, solid brass with wall brace] [Swing, roundtubular] [Swing, shaped tube] [Swing, solid brass] [Rigid gooseneck] [Swivel

gooseneck].

If retaining "laminar flow" option in "Spout Outlet" Subparagraph below, retain "Laminar-Flow, Faucet-Spout Outlets" Article.

13. Spout Outlet: [Aerator] [Swivel aerator/spray] [Spray] [Laminar flow] [Plain end].

14. Drain: [Stopper with chain] [Grid] [Lift and turn].

2.14 DISHWASHER AIR-GAP FITTINGS

A. Dishwasher Air-Gap Fittings :













35/45



g. Watts Brass & Tubular; a division of Watts Water Technologies, Inc.

h. .



36/45



D. Description: Chrome-plated-brass, faucet-spout outlet that produces non-aerating, laminar

stream. Include external or internal thread that mates with faucet outlet for attachment to

faucets where indicated and flow-rate range that includes flow of faucet.

2.16 DISPOSERS

Copy "Disposers" Paragraph below and re-edit for each type of food-waste disposer required.


disposer.

A. Disposers : [Batch] [Continuous]-feed household, food waste.











List of manufacturers below is for continuous-feed disposers.

g. American Standard America.

h. Anaheim Manufacturing, Inc.; a Subsidiary of Western Industries, Inc.

i. Franke Consumer Products, Inc.j. InSinkErator.

k. KitchenAid.

l. Maytag.

m. WhiteRock Corp.

n.


37/45



3. Standards: ASSE 1008 and UL 430, and listed and labeled as defined in NFPA 70, by a

qualified testing agency, and marked for intended location and application.

4. General: Include reset button; wall switch; corrosion-resistant chamber with jam-

resistant, cutlery- or stainless-steel grinder or shredder;NPS 1-1/2 (DN 40) outlet; quick-

mounting, stainless-steel sink flange; antisplash guard; and combination cover/stopper.5. Model: [Not applicable] [Sound-insulated chamber] [Sound-insulated chamber and

stainless-steel outer shell].6. Motor: 115-V ac, 1725 rpm, [1/3] [1/2] [3/4] [1] hp with overload protection.

2.17 HOT-WATER DISPENSERS



Copy "Hot-Water Dispensers" Paragraph below and re-edit for each type of flow-control, hot-water

dispenser required.

Insert number to complete drawing designation. Use these designations on Drawings to identify each hot-water dispenser.

B. Hot-Water Dispensers : [Gooseneck spout with lever handle]

[Spout with twist knob or push button], flow control.












List of manufacturers below is for spout with twist-knob or push-button, flow-control, hot-water

dispensers.



38/45



f. Anaheim Manufacturing, Inc.; a Subsidiary of Western Industries, Inc.

g. Elkay Manufacturing Co.

h. InSinkErator.

i. Just Manufacturing.

j. KitchenAid.k. .

2. Bowl:

a. Standards: ASME A112.19.2/CSA B45.1, ASME A112.19.5, and ASSE 1037.

b. Bowl Type: [Siphon jet] .c. Height: [Standard] [Child] [Handicapped/elderly].

d. Rim Contour: [Elongated] [Regular].

Retain first option in "Water Consumption" Subparagraph below unless special, low-consumption design

is required.



39/45



e. Water Consumption: [1.28 gal/flush 4 L/flush] [1.6 gal/flush 6 L/flush].

f. Color: [White] .

3. Toilet Seat: .4. Supply Fittings:

a. Standard: ASME A112.18.1/CSA B125.1.b. Supply Piping: Chrome-plated-brass pipe or chrome-plated-copper tube matching

water-supply piping size. Include chrome-plated wall flange.

c. Stop: Chrome-plated-brass, one-quarter-turn, ball-type or compression stop with

inlet connection matching water-supply piping type and size.

1) Operation: [Loose key] [Wheel handle] .

d. Riser:

1) Size: [NPS 3/8 (DN 10)] [NPS 1/2 (DN 15)].

2) Material: [Chrome-plated, soft-copper flexible tube] [ASME A112.18.6,

braided- or corrugated-stainless-steel flexible hose] riser.

Copy "Water Closets" Paragraph below and re-edit for each type of flushometer-tank, vitreous-china

water closet required.


water closet. Do not use same designation as is used for another water closet in other Division 22

plumbing-fixture Sections. See Specification Coordination Checklist for other Sections specifying water

closets.

B. Water Closets : Floor mounted, floor outlet, close coupled(flushometer tank), vitreous china.

1. Basis-of-Design Product: Subject to compliance with requirements, provide GerberPlumbing Fixtures LLC; [UltraFlush] [Brianne] [Maurice], or comparable product by

one of the following:

Retain one of four lists of manufacturers below. First list below is for Sloan's "Flushmate" flushometer-

tank, 1.0-gal./flush (3.8-L/flush) water closets.

a. .

List of manufacturers below is for Briggs's vacuum-assist, flushometer-tank, 1.1-gal/flush or 1.6-

gal./flush (4.1 or 6-L/flush) water closets.

f.


40/45



2. Bowl:

a. Standards: ASME A112.19.2/CSA B45.1 and ASME A112.19.5.

b. Bowl Type: [Siphon jet] .c. Height: [Standard] [Child] [Handicapped/elderly].

d. Rim Contour: [Elongated] [Regular].

Retain first option in "Water Consumption" Subparagraph below unless special, low-consumption design

is required.

e. Water Consumption: 1.1-gal/flush or 1.6-gal./flush(4.1-L/flush or 6-L/flush).

f. Color: [White] .

3. Toilet Seat: .

4. Supply Fittings:


b. Supply Piping: Chrome-plated-brass pipe or chrome-plated-copper tube matching

water-supply piping size. Include chrome-plated wall flange.c. Stop: Chrome-plated-brass, one-quarter-turn, ball-type or compression stop with

inlet connection matching water-supply piping type and size.

1) Operation: [Loose key] [Wheel handle] .

d. Riser:

1) Size: [NPS 3/8 (DN 10)] [NPS 1/2 (DN 15)].

2) Material: [Chrome-plated, soft-copper flexible tube] [ASME A112.18.6,


2.19 TOILET SEATS

Copy "Toilet Seats" Paragraph below and re-edit for each type of toilet seat required.


toilet seat.

A. Toilet Seats :



1. Manufacturers: Subject to compliance with requirements, [provide products by thefollowing] [provide products by one of the following] [available manufacturers








41/45





3. Standard: IAPMO/ANSI Z124.5.4. Material: Plastic.

5. Type: [Residential] [Commercial (Standard)].6. Shape: [Regular rim (Open front)] [Regular rim (Closed front)] [Elongated rim

(Open front)] [Elongated rim (Closed front)].

7. Configuration: [Closed] [Open] front [with] [without] cover.

8. Size: [Elongated] [Regular].

9. Hinge Type: [Check] [Self-sustaining] [Self-sustaining, check] [Self-raising].

10. Hinge Material: [Noncorroding metal] [Plastic].

11. Seat Cover: [Required] [Not required].

12. Color: [White] [Black] .

2.20 SUPPLY FITTINGS



B. Standard: ASME A112.18.1/CSA B125.1.

C. [Bidet] [Lavatory] [Bar Sink] [Kitchen Sink] [and] [Laundry Tray] Supply Fittings:

1. Supply Piping: Chrome-plated-brass pipe or chrome-plated-copper tube matching water-

supply piping size. Include chrome-plated wall flange.

2. Stops: Chrome-plated-brass, one-quarter-turn, ball-type or compression stop with inletconnection matching water-supply piping type and size.

a. Operation: [Loose key] [Wheel handle] .

3. Risers:

a. Size: NPS 3/8 (DN 10) for [bidets] [and] [lavatories].



42/45



b. Size: [NPS 3/8 (DN 10)] [NPS 1/2 (DN 15)] for [bar sinks] [kitchen sinks]

[and] [laundry trays].

c. Material: [Chrome-plated, soft-copper flexible tube] [ASME A112.18.6,


2.21 WASTE FITTINGS

1. Standard: ASME A112.18.2/CSA B125.2.

2. Drain: Grid type withNPS 1-1/4 (DN 32) offset tailpiece for accessible lavatories.

3. Drain: Pop-up type with NPS 1-1/4 (DN 32) straight tailpiece as part of faucet for

standard lavatories.

4. Drain: Grid type with NPS 1-1/2 (DN 40) offset tailpiece for accessible [bar sinks]

[and] [kitchen sinks].

5. Drain: Grid type with NPS 1-1/2 (DN 40) straight tailpiece for standard [bar sinks]

[and] [kitchen sinks] [and for laundry trays].6. Trap:

a. Size: [NPS 1-1/4 (DN 32)] [NPS 1-1/2 by NPS 1-1/4 (DN 40 by DN 32)][NPS 1-1/2 (DN 40)] for [bidets] [and] [lavatories].

b. Size: NPS 1-1/2 (DN 40) for [bar sinks] [kitchen sinks] [and] [laundry trays].

Retain one of three "Material" subparagraphs below.

c. Material: Chrome-plated, [two-piece, cast-brass trap and swivel elbow with0.032-inch- (0.83-mm-) thick brass tube to wall] [two-piece, cast-brass trap

and ground-joint swivel elbow with 0.032-inch- (0.83-mm-) thick brass tube to

wall] [one-piece, cast-brass trap with swivel 0.029-inch- (73-mm-) thick

tubular brass wall bend] ; and chrome-plated-brass or -steel

wall flange.

d. Material: Stainless-steel, two-piece trap and swivel elbow with 0.012-inch- (0.30-mm-) thick stainless-steel tube to wall; and stainless-steel wall flange.

e. Material: ASTM F 409 [ABS] [or] [PVC] [one] [two]-piece trap and waste to

wall and wall flange.

2.22 GROUT

A. Standard: ASTM C 1107/C 1107M, Grade B, post-hardening and volume-adjusting, dry,

hydraulic-cement grout.

B. Characteristics: Nonshrink; recommended for interior and exterior applications.

C. Design Mix: 5000-psi (34.5-MPa), 28-day compressive strength.

D. Packaging: Premixed and factory packaged.

PART 3 - EXECUTION



43/45



3.1 EXAMINATION

A. Examine roughing-in of water-supply and sanitary drainage and vent piping systems to verify

actual locations of piping connections before plumbing-fixture installation.

B. Examine walls, floors, cabinets, and counters for suitable conditions where fixtures will be

installed.

C. Proceed with installation only after unsatisfactory conditions have been corrected.

3.2 INSTALLATION

A. Install plumbing fixtures level and plumb according to roughing-in drawings.

B. Install floor-mounted water closets on closet flange attachments to drainage piping.

First paragraph below applies to counter-mounting fixtures such as lavatories and sinks.

C. Install counter-mounting fixtures in and attached to casework.

D. Install pedestal lavatories on pedestals and secured to wood blocking in wall.

E. Install water-supply piping with stop on each supply to each fixture to be connected to water

distribution piping. Attach supplies to supports or substrate within pipe spaces behind fixtures.

Install stops in locations where they can be easily reached for operation.

1. Exception: Use ball, gate, or globe valves if supply stops are not specified with fixture.

Comply with valve requirements specified in Division 22 Section "General-Duty Valves

for Plumbing Piping."

F. Install tanks for accessible, tank-type water closets with lever handle mounted on wide side ofcompartment.

G. Install toilet seats on water closets.

H. Install faucet flow-control fittings with specified flow rates and patterns in faucet spouts if

faucets are not available with required rates and patterns. Include adapters if required.

I. Install shower flow-control fittings with specified maximum flow rates in shower arms.

J. Install traps on fixture outlets.

1. Exception: Omit trap on fixtures with integral traps.2. Exception: Omit trap on indirect wastes unless otherwise indicated.

K. Install disposer in outlet of each sink indicated to have a disposer. Install switch where

indicated or in wall adjacent to sink if location is not indicated.

L. Install dishwasher air-gap fitting at each sink indicated to have air-gap fitting. Install [ in sink

deck] [on countertop at sink] . Connect inlet hose to dishwasher and outlet

hose to disposer.



44/45



M. Install hot-water dispensers in back top surface of sink or in countertop with spout over sink.

N. Set [bathtubs] [baths] [and] [shower receptors] in leveling bed of cement grout.

Indicate on Drawings those lavatories and sinks that are required to be accessible.

O. Install protective shielding pipe covers and enclosures on exposed supplies and waste piping ofaccessible [lavatories] [and] [sinks]. Comply with requirements in Division 22 Section

"Plumbing Piping Insulation."

P. Install wall flanges or escutcheons at piping wall penetrations in exposed, finished locations.

Use deep-pattern escutcheons if required to conceal protruding fittings. Comply with

escutcheon requirements specified in Division 22 Section "Escutcheons for Plumbing Piping."

Q. Seal joints between plumbing fixtures, counters, floors, and walls using sanitary-type, one-part,

mildew-resistant silicone sealant. Match sealant color to fixture color. Comply with sealant

requirements specified in Division 07 Section "Joint Sealants."

3.3 CONNECTIONS

Coordinate piping installations and specialty arrangements with schematics on Drawings and with

requirements specified in piping systems. If Drawings are explicit enough, these requirements may be

reduced or omitted.

A. Connect fixtures with water supplies, stops, and risers, and with traps, soil, waste, and vent

piping. Use size fittings required to match fixtures.

B. Comply with water piping requirements specified in Division 22 Section "Domestic Water

Piping."

C. Comply with soil and waste piping requirements specified in Division 22 Section "Sanitary

Waste and Vent Piping."

D. Install protective shielding pipe covers and enclosures on exposed supplies and waste piping of

accessible [lavatories] [and] [sinks]. Comply with requirements in Division 22 Section

"Plumbing Piping Insulation."

3.4 ADJUSTING

A. Operate and adjust plumbing fixtures and controls. Replace damaged and malfunctioning

fixtures, fittings, and controls.

B. Adjust water pressure at faucets to produce proper flow.

3.5 CLEANING AND PROTECTION

A. After completing installation of plumbing fixtures, inspect and repair damaged finishes.



45/45



B. Clean plumbing fixtures, faucets, and other fittings with manufacturers' recommended cleaning

methods and materials.

C. Provide protective covering for installed plumbing fixtures and fittings.

D. Do not allow use of plumbing fixtures for temporary facilities unless approved in writing by

Owner.

END OF SECTION 224100

224100 fl.residential plumbing fixtures.gerber plumbing fixtures

Documents