20556q 1-5 punch & flare die set - eastwood#20531 2" die set 2-1/8" i.d, hole x...
TRANSCRIPT
1", 1.5", 2", 2.5" PUNCH & FLARE DIE SETS
INSTRUCTIONS
Item #20556
© Copyright 2015 Easthill Group, Inc. 9/15 Instruction item #20556Q Rev 2
If you have any questions about the use of this product, please contact The Eastwood Technical Assistance Service Department: 800.544.5118 >> email: [email protected]
PDF version of this manual is available online >> eastwood.com/20556manual
The Eastwood Company 263 Shoemaker Road, Pottstown, PA 19464, USAUS and Canada: 800.345.1178 Outside US: 610.718.8335
Fax: 610.323.6268 eastwood.com
ADDITIONAL ITEMS#20533 1” Punch & Bead Die Set
#20356 1-1/2” Punch & Bead Die Set
#20534 2” Punch & Bead Die Set
#20535 2-1/2” Punch & Bead Die Set
MAINTENANCE• Keep the die set clean. Remember to remove slugs from die after each use.
• Keep a light coating of machine oil on all surfaces to prevent rust.
• Store in a clean & dry environment when not in use.
2 Eastwood Technical Assistance: 800.544.5118 >> [email protected] To order parts and supplies: 800.345.1178 >> eastwood.com 3
The EASTWOOD PUNCH & FLARE DIE SETS will punch a clean hole and produce a smoothly radiused, 45 degree fl are in aluminum and mild steel in a choice of 4 sizes.
FINISHED FLARED HOLE DIMENSIONS
#20530 1" Die Set 1-1/8" I.D, Hole x 1/4" Deep Flare
#20355 1.5" Die Set 1-5/8" I.D, Hole x 1/4" Deep Flare
#20531 2" Die Set 2-1/8" I.D, Hole x 1/4" Deep Flare
#20532 2.5" Die Set 2-5/8" I.D, Hole x 1/4" Deep Flare
MAXIMUM MATERIAL THICKNESS
Aluminum 14 Ga (.064")
Mild Steel 16 Ga (.060")
Stainless Steel 19 Ga (.044")
INCLUDES(1) Bolt (2) Washers (1) Male Flare Die (1) Inner Cutting Die (1) Female Flare Die
OPERATIONPUNCH & FLARE
• Determine the position and direction of the fi nished fl ared hole.
• Drill a ½" hole at the center of the location.
• Firmly secure the work-piece.
• Lubricate washers.
• Assemble the tool in the order shown (Fig A) & (Fig B).
• From left to right, stack two thrust washers and Male Flare Die onto the Bolt. Insert the end of the Bolt through the hole drilled in the work-piece. On the opposite side of the work-piece, assemble the Inner Cutting Die and thread on the Female Flare Die, with the mating cavity facing the Male Flare Die and Inner Cutting Die.
• Tighten the Bolt by hand until resistance is felt.
• Using a wrench or socket, continue to turn the Bolt until the material is pierced and the feature is formed.
• Disassemble tool in reverse order.
FIG. A
FIG. B
Bolt
2 Washers
Inner Cutting Die Female
Flare Die
��✓�����
��✓�����
��✓�����
��✓�����
Male Flare Die
��✓�����
Work Piece
��✓�����
FIG. BFIG. BSAFETY INFORMATIONIn this manual, on the labeling, and all other information provided with this product:
WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION used with the safety alert symbol, indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
Finished Result READ INSTRUCTIONS Read this entire manual before set up and use of this tool.
Save this instruction manual for future reference.
INJURY HAZARDS• Do not use impact wrenches with this tool.• Always wear ANSI rated eye protection when using this tool.• Pinch Hazard! Keep fi ngers away from the moving parts when operating.• Wear appropriate work gloves and protective clothing. Sheet metal will often
have sharp edges which can cause cuts to hands and arms.
Never attempt to use this tool on materials thicker than those shown as
serious tool damage can result.
2 Eastwood Technical Assistance: 800.544.5118 >> [email protected] To order parts and supplies: 800.345.1178 >> eastwood.com 3
The EASTWOOD PUNCH & FLARE DIE SETS will punch a clean hole and produce a smoothly radiused, 45 degree fl are in aluminum and mild steel in a choice of 4 sizes.
FINISHED FLARED HOLE DIMENSIONS
#20530 1" Die Set 1-1/8" I.D, Hole x 1/4" Deep Flare
#20355 1.5" Die Set 1-5/8" I.D, Hole x 1/4" Deep Flare
#20531 2" Die Set 2-1/8" I.D, Hole x 1/4" Deep Flare
#20532 2.5" Die Set 2-5/8" I.D, Hole x 1/4" Deep Flare
MAXIMUM MATERIAL THICKNESS
Aluminum 14 Ga (.064")
Mild Steel 16 Ga (.060")
Stainless Steel 19 Ga (.044")
INCLUDES(1) Bolt (2) Washers (1) Male Flare Die (1) Inner Cutting Die (1) Female Flare Die
OPERATIONPUNCH & FLARE
• Determine the position and direction of the fi nished fl ared hole.
• Drill a ½" hole at the center of the location.
• Firmly secure the work-piece.
• Lubricate washers.
• Assemble the tool in the order shown (Fig A) & (Fig B).
• From left to right, stack two thrust washers and Male Flare Die onto the Bolt. Insert the end of the Bolt through the hole drilled in the work-piece. On the opposite side of the work-piece, assemble the Inner Cutting Die and thread on the Female Flare Die, with the mating cavity facing the Male Flare Die and Inner Cutting Die.
• Tighten the Bolt by hand until resistance is felt.
• Using a wrench or socket, continue to turn the Bolt until the material is pierced and the feature is formed.
• Disassemble tool in reverse order.
FIG. A
FIG. B
Bolt
2 Washers
Inner Cutting Die Female
Flare Die
��✓�����
��✓�����
��✓�����
��✓�����
Male Flare Die
��✓�����
Work Piece
��✓�����
FIG. BFIG. BSAFETY INFORMATIONIn this manual, on the labeling, and all other information provided with this product:
WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION used with the safety alert symbol, indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
Finished Result READ INSTRUCTIONS Read this entire manual before set up and use of this tool.
Save this instruction manual for future reference.
INJURY HAZARDS• Do not use impact wrenches with this tool.• Always wear ANSI rated eye protection when using this tool.• Pinch Hazard! Keep fi ngers away from the moving parts when operating.• Wear appropriate work gloves and protective clothing. Sheet metal will often
have sharp edges which can cause cuts to hands and arms.
Never attempt to use this tool on materials thicker than those shown as
serious tool damage can result.
1", 1.5", 2", 2.5" PUNCH & FLARE DIE SETS
INSTRUCTIONS
Item #20556
© Copyright 2015 Easthill Group, Inc. 9/15 Instruction item #20556Q Rev 2
If you have any questions about the use of this product, please contact The Eastwood Technical Assistance Service Department: 800.544.5118 >> email: [email protected]
PDF version of this manual is available online >> eastwood.com/20556manual
The Eastwood Company 263 Shoemaker Road, Pottstown, PA 19464, USAUS and Canada: 800.345.1178 Outside US: 610.718.8335
Fax: 610.323.6268 eastwood.com
ADDITIONAL ITEMS#20533 1” Punch & Bead Die Set
#20356 1-1/2” Punch & Bead Die Set
#20534 2” Punch & Bead Die Set
#20535 2-1/2” Punch & Bead Die Set
MAINTENANCE• Keep the die set clean. Remember to remove slugs from die after each use.
• Keep a light coating of machine oil on all surfaces to prevent rust.
• Store in a clean & dry environment when not in use.