203mdz_inbio460 installation guide zkaccess

8/12/2019 203MDZ_Inbio460 Installation Guide ZKACCESS

1/24

www.ZKAccess.com
http://www.zkaccess.com/http://www.zkaccess.com/


2/24

Safety Precautions

Product Contents

Product PIN Diagram

LED indicators

Product Dimensions

Installation of Panel with Casing

Wire Legend

Power Wiring Diagram

FR1200 Connection

Weigand Connection

Exit button Connection

Lock connection

Door Sensor Connection

Aux. Input Connection

Aux. Output Connection

Ethernet Connection

RS485 Connection

DIP switch settings

Electrical Specifications

Troubleshooting

Specifications

1

02

0406

06

07

08

091011

1212

13

1315

15

1617

18

1920

21
http://www.zkteco.com/


3/24

1

2

Safety Precautions

Do not install the device in an area

subject to direct sun light, Humidity

or dust

Do not place a magnet near the

product. Magnetic objects such as

magnet, CRT, TV, monitor or speaker

may damage the device.

Do not place the device next to

heating equipments

Be careful not to let liquid like

water, drinks or chemicals leak

inside the device.

Clean the device often to remove

dust on it

01 02 03

04 05 06

Do not let children touch the

device without supervision.

The list below is to keep users safety and prevent any loss. Please read carefully before installation.


4/24


5/244

Product Contents

Basic Contents

Inbio460

Wall Mounting Screws2 pcs. Wall Plugs2 pcs. Surge Suppressing Diode4 p

Screw Driver 2 pcs. Software CD InBio Installation Guide


6/245

Product Contents

Optional accessories

Weigand Card Reader Prox Card

Card EnrollerZK4500 FP Enrollment reader

FR1200 FP Reader K1-1 Exit Button

Inbio Metal Case RS485 convertor


7/246

Product PIN Diagram

#4 Door Card

Reader

#4 Door Exit

Button

#3 Door Card

Reader

#3 Door Exit

Button

#2 Door Exit

Button

#2 Door Card

Reader

#1 Door Card

Reader

#1 Door Exit

Button

State Indictor

FR1200

Fingerprint

Reader

Aux Input 4

Aux Input 1

SD Card Slot

LINK LED

ACT LED

Ethernet Port

DIP Switch

PC RS485 Port

Aux Output 1

Aux Output 4

#1 Door Lock

#4 Door Sensor

Lock Power

Inbio Power

LED indicators

LINK

(Green)

LED solid green indicates

TCP/IP communication is

normal

ACT

(Yellow)

Flashing LED indicates data

communication is in progress

EXT RS485

(Yellow &

Green)


communication in progress

PC RS485

(Yellow &

Green)


communication is in progress

POWER

(Red)

Flashing LED indicates the

panel is powered on.

RUN(Green)

Flashing LED indicates that

panel is in normal workingmode

CARD

(Yellow)

Flashing LED indicates that

the card is read by the panel.

#1 Door Sensor

#4 Door Lock


8/24


9/248

Installation of Panel & Case

Metal Case


10/24

Wire Legend

9

Detector Infrared sensors FR1200 Inbio-Box #1Exit Button #1Card Reader #4 Exit Switch #4 Card Reader

12V

Power SupplyNormally Open LockNormally Close LockAlarmFloodlightRS485 ConvertorNetwork

12V DC

PowerDC

i i di


11/24

Power wiring diagram

10

WithBackup Battery

AC

Switching power supply

Inbio460

AC

Switching power supply

Inbio460

Backup Battery

+

-

110-220V

110-220V

Without

Backup Battery

FR1200 C i


12/24

FR1200 Connection

11

#1 FR1200 #2 FR1200 #3 FR1200 #8 FR1200

DIP Switch Setting For FR1200 Device ID

1. There are six DIP switches on the back of FR1200 , Switches 1-4 is for RS485

address , switch 5 is reserved , switch 6 is for reducing noise on long RS485 cable.

2. Set the odd number for IN reader, and the even number for OUT reader(for eg.

For two readers for one door- the RS485 address 1 is for IN reader, RS485 address

2 is for OUT reader )

3. If FR1200 is powered from Inbio460 panel ,the length of wire should be less

than 100 meters or 330 ft.

4. The External RS485 interface can supply maximum 500mA current , The

FR1200s startup current is 240mA. So Inbio460 only can only power two FR1200s.5. If the cable length is more than 200 meters or 600 ft , the number 6 switch

should be ON as below

Important Notes

12V DC

12V DC

Distance

More than 200 meters

W i d C ti


13/24

Weigand Connection

12

Weigand Card Reader

Exit Button Connection

Beeper

Green LED

Weigand D1

Weigand D0

GND

DC+(6-14V)

BUT

GND

DV12VDV12V

NO

COM

NC

separate power supply

NoticeZK ABK Exit Button

K1-1 Exit Switch

12V DC Power Supply

L k C ti


14/24

13

Lock Connection

12V DC

GND

Sensor

Sensor

12V DC

GND

GND

12V DC

Sensor

Sensor

GND

12V DC

FR107

FR107For Normally Open -Lock powered from panel power supply

For Normally Closed -Lock powered from panel power supply

Lock Connection


15/24

Lock Connection

14

Important Notes:

InBio is set to supply lock power by default from built-in

power supply , If you want to use external power supply ,

you must take the following steps

1. Take apart the cover of inbio460

2. Select the desired lock relay and find its jumpers

3. Take off the jumpers and change to

4. Connect the lock as shown in the diagram below.

Steps:

Inbio460 Detach from Rail Remove Top Cover Lock Relay

Terminals Default SettingChanged Setting Jumpers

FR107

GND

12V DC

SEN SEN GND 12V DC

5 1 15 5 1 15

Connecting a Lock with External Power supply

Switching Wet Contact to Dry Contact

Auxiliary Input/Output


16/24

15

Auxiliary Input/Output

Aux. Input Connection

Aux. output Connection

COM

NO

NC

GND12V DC

COM

NO

NC

GND12V DC

Smoke Detector

Alarm

Ethernet Connection


17/24

16

Ethernet Connection

Direct connection

To connect Inbio460 with a PC directly, connect both devices with a straight network cable. As the Inbio460 supports auto MDI/MDIX ,

it is not necessary to use a crossover type cable.

Important Notes:

ZK4500 Enrollment

readerCR10 Card Issuer

1. Both 10Base-T and 100Base-T

are supported2. The cable length must be less

than 100 meters or 330 ft.

3. For more than 100 meters ,

please use HUB to amplify the

signal

TCP/IP

CR10 Card Issuer

ZK4500 Enrollment

reader

The CR10 and ZK4500 are connected to the server

using USB connection.

RS485 Connection


18/24

17

RS485 Connection

Important Notes

#1 Inbio460

#63 Inbio460

Do's and Dont's for RS 485 connection

RS485-RS485+GND

1. RS485 communication wires should be a shielded or twisted pair cable.

RS485 communication wires should be connected in a bus cascade instead

of a star form, to achieve a better shielding effect by reducing signal

reflection during communications.

2. A single 485 bus can be connected with 63 access control panels at the

most, but preferably less than 32 panels should be connected.

3. To eliminate signal attenuation in communication cables and suppress

interference, if the bus is longer than 200 meters, set the number 8 DIP

switch to the ONposition. This is equivalent to a parallel connection of one

120ohm resistance between the 485+ and 485- lines.

Distance

More than 200 meters

#1 Inbio460 #* Inbio460

DIP Switch Setting


19/24

18

DIP Switch Setting

Introduction RS485 Address

1. Number 1-6 are reserved to set the device number for RS485

communication. The code is binary, and the numbering starts from left to

right. When the switch is set to ON position, it indicates 1 (on); when the

switch is set downwards, it indicates 0 (off). For example, to set a device

number 39=1+2+4+32, which corresponds to the binary code 111001, put

number 1, 2, 3, and 6 to ON position, as illustrated below.

2. For more details, please check the table at the end of this document

Restore factory setting

1. If you forget the inBio IP address or the device does not work

normally, you can use the number 7 terminal to restore inbio460 to

factory default settings. The parameters which gets reset are

device IP address, communication password ,gateway ,subnet mask.

2. The switch is OFF by default. When it is moved upwards anddownwards for three times within 10 seconds and finally returned

to OFF position, the factory settings will be restored after the

access control panel is restarted.

1 times 2 times 3 times OFF

Terminal Resistance

1. Number 8 is for setting the RS485 termination resistance. Putting the

switch to ON position is equivalent to parallel connection of a 120ohm

termination resistance between 485+ and 485-

2. As shown in diagram below, for more info please read RS485 connection

important notes

120ohm

Electrical Specification


20/24

Electrical Specification

19

Min. Typ. Max. Notes

Working power supply

Voltage(V) 9.6 12 14.4 Use regulated DC power adaptor only

Current(A) 2

Electronic lock relay output

Switching voltage(V) 36V Use regulated DC power adaptor only

Switching Current(A) 2

Auxiliary relay output

Switching voltage(V) 36V Use regulated DC power adaptor only

Switching Current(A) 1.25

Switch Aux. input

VIH (V) TBD

VIL (V) TBD

Pull-up resistance () 4.7k The input ports are pulled up with 4.7k resistors

WEIGAND Input

Voltage(V) 10.8 12 13.5

Current(mA) 500

ZK Electronic lock

Voltage(V) 10.8 12 13.2

Current(mA) 500

Troubleshooting


21/24

Troubleshooting

20

1. Fingerprint can not be read well or it takes too long.

Check whether a finger or fingerprint sensor is stained with sweat, water, or dust

Retry after cleaning the finger and fingerprint sensor with dry cloth.

If a finger is way too dry, rub your finger on the palm and retry.

Try to reset fingerprint sensor by pressing the reset button at the bottom of the reader

2. Fingerprint is matched but authorization keeps failing.

Check whether the user access is restricted.

Inquire with administrator whether the enrolled fingerprint has been deleted from the device

for some reason.

3. How Many kinds of WEIGAND format can be supported. The panel is set to read 26 bit by default.

However there are 9 other bit formats which can be selected from the software. In addition you

can also define your custom bit format.

4. How many verification modes can be support.

Card Only

Fingerprint Only Password Only

Card plus fingerprint

Card plus password

Card or fingerprint

Reset Button

Specification


22/24

Specification

21

Communication RS485, Ethernet

Baud Rate for RS485 9600-115200 baud

Power Supply 12V DC, 3A

Device Capacity Card capacity 30,000 ; Log events capacity 100,000 ; Finger capacity 3,000

LED Indicator Indication for communication, power, status and prox card

Environment Operating Temp: 32-113F (0-45C) Operating Humidity: 20% to 80%

Number of doors controlled four door one way or two door two way

Number of card readers supported 4

Number of FR1200 supported 8

FR1200 Sensor Fingerprint sensor 500dpi Optical / Optical sensor

Types of readers supported 26-bit Weigand, others upon request

Number of Inputs 12 (4 Exit Device, 4 Door Status, 4 AUX)

Number of Outputs 8 (4- Form C relay for lock and 4- Form C relay for Aux output)

Weight 7.8lbs (3.55kg)

Enclosure Stainless Steel

Mounting Wall Mount

Dimensions (Bundle Only) 15.7in. 3.56in. 13.0in. 400mm(L) X 90.5mm(W) X 330mm(H)

Dimensions ( Board Only) 8.89in. 4.17in. 1.42in. 226mm(L) X 106mm(W) X 36mm(H)

CPU 32 bit 400MHz

RAM 32MB

Flash 128MB

Certified

PC485 Table


23/24

22

Place AddressSwitch Setting

1 2 3 4 5 6Address No. 1 2 4 8 16 32

01 ON OFF OFF OFF OFF OFF02 OFF ON OFF OFF OFF OFF03 ON ON OFF OFF OFF OFF04 OFF OFF ON OFF OFF OFF05 ON OFF ON OFF OFF OFF06 OFF ON ON OFF OFF OFF07 ON ON ON OFF OFF OFF08 OFF OFF OFF ON OFF OFF09 ON OFF OFF ON OFF OFF10 OFF ON OFF ON OFF OFF11 ON ON OFF ON OFF OFF12

OFF

OFF

ON

ON

OFF

OFF

13 ON OFF ON ON OFF OFF14 OFF ON ON ON OFF OFF15 ON ON ON ON OFF OFF16 OFF OFF OFF OFF ON OFF17 ON OFF OFF OFF ON OFF18 OFF ON OFF OFF ON OFF19 ON ON OFF OFF ON OFF20 OFF OFF ON OFF ON OFF21 ON OFF ON OFF ON OFF22 OFF ON ON OFF ON OFF23 ON ON ON OFF ON OFF24 OFF OFF OFF ON ON OFF25 ON OFF OFF ON ON OFF26 OFF ON OFF ON ON OFF27 ON ON OFF ON ON OFF28 OFF OFF ON ON ON OFF29 ON OFF ON ON ON OFF30 OFF ON ON ON ON OFF31 ON ON ON ON ON OFF32 OFF OFF OFF OFF OFF ON

Place AddressSwitch Setting

1 2 3 4 5 6Address No. 1 2 4 8 16 32

33 ON OFF OFF OFF OFF ON34 OFF ON OFF OFF OFF ON35 ON ON OFF OFF OFF ON36 OFF OFF ON OFF OFF ON37 ON OFF ON OFF OFF ON38 OFF ON ON OFF OFF ON39 ON ON ON OFF OFF ON40 OFF OFF OFF ON OFF ON41 ON OFF OFF ON OFF ON42 OFF ON OFF ON OFF ON43 ON ON OFF ON OFF ON44 OFF OFF ON ON OFF ON45 ON OFF ON ON OFF ON46 OFF ON ON ON OFF ON47 ON ON ON ON OFF ON48 OFF OFF OFF OFF ON ON49 ON OFF OFF OFF ON ON50 OFF ON OFF OFF ON ON51 ON ON OFF OFF ON ON52 OFF OFF ON OFF ON ON53 ON OFF ON OFF ON ON54 OFF ON ON OFF ON ON55 ON ON ON OFF ON ON56 OFF OFF OFF ON ON ON57 ON OFF OFF ON ON ON58 OFF ON OFF ON ON ON59 ON ON OFF ON ON ON60 OFF OFF ON ON ON ON61 ON OFF ON ON ON ON62 OFF ON ON ON ON ON63 ON ON ON ON ON ON


24/24

ZK USA office:

201 Circle Drive North, Suite 116

Piscataway, NJ 08854, USA

Tel: +1 732-412-6007

Fax +1 732-412-6008

[email protected]

zkaccess.com

Copyright 2013 ZKAccess Inc. All right reserved.

ZKAccess May, at any time and without notice , Make changes or

improvements to the product and services offered and/or cease

producing or commercializing them.

Functions and specifications of the product are subject to change without notice due to quality enhancement or function update. For any inquiry

for the product, please contact ZKAccess Inc .

203mdz_inbio460 installation guide zkaccess

Documents