d38kgjogivm3r3.cloudfront.net · 2020. 6. 23. · a definitive guide to design for manufacturing...
TRANSCRIPT
-
Title
Subtitle
-
2 A DEFINITIVE GUIDE TO DESIGN FOR MANUFACTURING SUCCESS
Sheet Metal Design Guidelines Hem Design Guidelines
Issue XII, June 2015
-
3 A DEFINITIVE GUIDE TO DESIGN FOR MANUFACTURING SUCCESS
Copyright Notice
© Geometric Limited. All rights reserved.
No part of this document (whether in hardcopy or electronic form) may be reproduced, stored in a retrieval system,
or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, to any
third party without the written permission of Geometric Limited. Geometric Limited reserves the right to change
the information contained in this document without prior notice.
The names or trademarks or registered trademarks used in this document are the sole property of the respective
owners and are governed/ protected by the relevant trademark and copyright laws.
This document is provided by Geometric Limited for informational purposes only, without representation or
warranty of any kind, and Geometric Limited shall not be liable for errors or omissions with respect to the
document. The information contained herein is provided on an “AS-IS” basis and to the maximum extent permitted
by applicable law, Geometric Limited hereby disclaims all other warranties and conditions, either express, implied
or statutory, including but not limited to, any (if any) implied warranties, duties or conditions of merchantability, of
fitness for a particular purpose, of accuracy or completeness of responses, of results, of workmanlike effort, of lack
of viruses, and of lack of negligence, all with regard to the document.
THERE IS NO WARRANTY OR CONDITION OF NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHTS WITH
REGARD TO THE DOCUMENT. IN NO EVENT WILL GEOMETRIC LIMITED BE LIABLE TO ANY OTHER PARTY FOR LOST
PROFITS, LOSS OF USE, LOSS OF DATA, OR ANY INCIDENTAL, CONSEQUENTIAL, DIRECT, INDIRECT, OR SPECIAL
DAMAGES WHETHER UNDER CONTRACT, TORT, WARRANTY, OR OTHERWISE, ARISING IN ANY WAY OUT OF THIS
DOCUMENT, WHETHER OR NOT SUCH PARTY HAD ADVANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGES.
-
4 A DEFINITIVE GUIDE TO DESIGN FOR MANUFACTURING SUCCESS
.
Welcome to another issue of the DFM Guidebook. We highly appreciate your feedback on our previous issues. Please continue to send us your comments and suggestions for subsequent issues.
This week we cover important design guidelines for sheet metal hemming.
Hemming is a sheet metal forming operation in which the edge of the sheet is folded back on itself. It serves several purposes: to fasten two sheet metal parts, to improve the appearance of edges (remove burrs and rough edges) and to increase the part stiffness. Hemming is also critical to the overall part functionality as well as assembly quality. There are mainly three types of hems: closed hem, open hem and teardrop hem. In this issue we cover DFM guidelines that can help increase the manufacturability of designs for press brake machines. Read the guidebook for specific guidelines like Open Hem, Rolled Hem, Tear Drop Hem, Rolled Hem to Hole edge Distance, Closed Hem and Knife Edge. If you have any feedback or questions on DFM guidebook, please write to us at [email protected]
Rahul Rajadhyaksha Senior Product Manager Geometric Limited
mailto:[email protected]
-
5 A DEFINITIVE GUIDE TO DESIGN FOR MANUFACTURING SUCCESS
Contents
Open Hem ............................................................................................................... 6
Rolled Hem .............................................................................................................. 7
Tear Drop Hem ........................................................................................................ 8
Rolled Hem to Hole Edge Distance ......................................................................... 9
Closed Hem ........................................................................................................... 10
Knife Edge ............................................................................................................. 11
-
6 A DEFINITIVE GUIDE TO DESIGN FOR MANUFACTURING SUCCESS
Open Hem
A Hem has a full round feature and a return flange. In open hem bend angle is equal to 180
degrees.
It is recommended that the ratio of the open hem radius to the sheet metal thickness should be
greater than or equal 0.5.
Also, the ratio of return flange height to the sheet metal thickness should be greater than or
equal to 4.
Where,
H = Return flange height
D = Open hem diameter
T = Sheet metal thickness
-
7 A DEFINITIVE GUIDE TO DESIGN FOR MANUFACTURING SUCCESS
Rolled Hem
It is recommended that the ratio of the external radius of a rolled hem to material thickness
should be greater than or equal to 2.
Also, the ratio of the rolled hem opening to material thickness should be greater than or equal to
1.
R = Rolled hem's external radius
D = Rolled hem's opening
-
8 A DEFINITIVE GUIDE TO DESIGN FOR MANUFACTURING SUCCESS
Tear Drop Hem
In tear drop hem the bend angle is greater than 180 degrees. It is recommended to consider the
following guidelines while designing a tear drop hem -
The ratio of the radius of a tear drop hem to the sheet metal thickness should be greater
than or equal to 0.5
The ratio of the return flange height to the sheet metal thickness should be greater than or
equal to 4.0
The ratio of the hem opening (spacing between the hem edge and the part) to the sheet
metal thickness should be greater than or equal to 0.25
Where,
d = Diameter of a tear drop hem.
H = Return flange height of the tear drop hem.
D= Hem Opening
T = Sheet Metal Thickness
-
9 A DEFINITIVE GUIDE TO DESIGN FOR MANUFACTURING SUCCESS
Rolled Hem to Hole Edge Distance
The ratio of the distance between the rolled hem and the edge of a hole to the sheet thickness
should be greater than or equal to 1.
T = Sheet metal thickness
D = Distance
-
10 A DEFINITIVE GUIDE TO DESIGN FOR MANUFACTURING SUCCESS
Closed Hem
Hems without any inside radius are called as closed hem. Closed hems are not recommended if
the hem geometry is to be painted or if the material used is SST or Aluminum.
In closed hems, return flange length from outside the bend should be equal to or greater than
four times the material thickness.
H = Return flange height of the tear drop hem
T = Sheet Metal Thickness
-
11 A DEFINITIVE GUIDE TO DESIGN FOR MANUFACTURING SUCCESS
Knife Edge
Knife edge features on sheet metal parts should be avoided for ease of manufacturing. To achieve
knife edges on sheet metal parts, additional operations may be required which increases the cost
of the product. Knife edge conditions can also lead to fatigue failures in certain conditions.
It is recommended to avoid knife edge conditions as it can either increase the manufacturing cost
and complexity or lead to fatigue failures.