2018/19...ami wet area membranes are tested to australian standard (as4858) and perform in the top...
TRANSCRIPT
2018/19Waterproofing Membranes
1800 099 990
amimembraneindustries.com.au
AUSTRALIAN MEMBRANE INDUSTRIES - 1800 099 990
Contents
Warranty .................................................................. 1
AMI Range AS4858 Tested Membranes ................. 2
Wet Area Membranes – AS3740 ........................ 3 - 5
Polyurethane Membranes ....................................... 6
Roof & External Membranes .............................. 6 - 7
Heat Membranes ................................................ 7 - 8
Special Roof Membranes ........................................ 9
Planter Boxes ........................................................ 10
Top Coat Sealers/Primers...................................... 11
Waterbased Epoxy ................................................ 12
Non-Slip Coating / Sealants .................................. 13
AUSTRALIAN MEMBRANE INDUSTRIES - 1800 099 990
AUSTRALIAN MEMBRANE INDUSTRIES - 1800 099 990
AMI MembranesThe AMI range of membranes were developed in conjunction with waterproofing applicators. AMI wet area membranes are tested to Australian Standard (AS4858) and perform in the top level of wet area membrane available in Australia.
The AMI range covers wet area waterproofing (AS3740) as well as exterior (AS 4654.1 and AS 4654.2) and roof membrane application.
WarrantyWET AREAS
AMI wet area CSIRO certified membranes are guarantee for 15 years subject to application in accordance with AS3740 and AMI’s technical data sheet.
EXTERNAL
AMI external membrane warranty varies on the type of membrane used and site. All external membranes are initially guaranteed for 8 years. This can be extended a further 8 years with a light UV top coat application.
20 and 25 year warranty is available for AMI’s unique silicone membranes and silicone membrane systems.
GENERAL MEMBRANES
Contact AMI
1
AUSTRALIAN MEMBRANE INDUSTRIES - 1800 099 990
Flowthane Ultra Flex Ultra Flex 50 PU115V P96
CSIRO Test NumberAS4858 3062-1 4522 5541 6028-4e 4080
Membrane Type Latex/SBR Acrylic/Urethane blend
Acrylic/Urethane blend Polyurethane Latex/SBR
Maximum Strain 770% 662% 963% 910% 242%
Water Immersion 1151% 1247% 1472% 1220% 530%
Bleach Immersion 919% 1447% 1391% 1244% 427%
Detergent Immersion 967% 1062% 1628% 1094% 195%
Heat Ageing 685% 457% 599% 1144% 147%
Drying Time - 25 C 1-2 hrs 1-2 hrs 1-2 hrs 6 - 8 hours 1-2 hrs
Reinforced when tested no no no no yes
Class III III III III II
AMI’s range of CSIRO AS4858 tested membranes.
AUSTRALIAN MEMBRANE INDUSTRIES - 1800 099 9902
WET AREA MEMBRANES
AUSTRALIAN MEMBRANE INDUSTRIES - 1800 099 990
Wet Area Membranes(Extensive technical and data sheets are available from AMI; the catalogue shows an overview of our range).
FLOWTHANE FAST CUREA special version of Flowthane that cures up to 60% faster than the standard product. Excellent for below ground and cold environment application.
Fast Cure
1800 099 990RX3 RX3
Safe Use and First Aid.
AMI membranes are safe waterbased products
however, avoid contact with the skin and eyes,
use goggles and gloves at all times. Do not
induce vomiting if product is ingested, flush
eyes thoroughly for at least 15 minutes with
clean water. Give water to drink and seek
medical assistance. The use of gloves and eye
protection is always recommended.
Use the product in accordance with good
industrial procedures.
IMPORTANT: The performance of the product is
dependent upon correct application onto surfaces
for which it is intended. Product to be applied
strictly in accordance with instructions onto
correctly prepared surfaces, which shall remain
sound, stable and free of cracking or movement.
Deviation from application instructions may
diminish or negate the performance of product.
Under no circumstances will the company be
liable for any loss, consequential or otherwise,
arising from the use of the product. Should this
product be proved defective our liability shall
be limited to the replacement of the product.
ALWAYS TEST ADHERE if in doubt. We
reserve the right to amend specifications and
applications techniques without prior notice. If
in doubt, contact the manufacturer.
ELASTICISED WATERPROOFING MEMBRANE
FLOWTHANE
Australian Membrane Industries Pty Ltd
PO BOX 242 GLENORIE NSW 2157 AUSTRALIA
Phone:1800 099 990 [email protected]
Fax: 61 2 9652 0411 www.amimembraneindustries.com.au
NON HAZARDOUS
CERTIFIED PRODUCT
FLOWTHANE
FLOWTHANE 500LMFlowthane is a certified Class III - high extensibility SBR membrane (CSIRO tested). Flowthane has been in commercial production since 2002.
Flowthane is non-UV resistant, rubberized, water-based, fast drying waterproof membrane available in a variety of colours.
Priming System: GP Primer – Sealpoxy
Available in blue and dark grey. In 15 litre and 5 litre pails.
Elongation Fowthane 500LM Duram Durabit EF Davco K10 Plus ASA Dampfix Gold
Control 770% 589% 563% 636%
Water Immersion 1151% 905% 917% 1655%
Bleach Immersion 919% 592% 882% 564%
Detergent Immersion 967% 868% 655% 1354%
Heat Ageing 685% 517% 509% 391%
Drying Time at 20C 1-2 Hours 4-6 Hours 6-8 Hours 4-6 Hours
Class III III III III
How Flowthane compares against our competition
3
WET AREA MEMBRANES
AUSTRALIAN MEMBRANE INDUSTRIES - 1800 099 990
AQUATHANE XRSBR membrane which is a Class III certified wet area membrane. Aquathane XR is fast drying and will not emulsify once it has dried (as opposed to cured). The product comes in blue /black colour and exhibits similar characteristics as Flowthane. Not UV resistant.
Priming System: GP Primer – Sealpoxy
Available in 15 litre pails.
1800 099 990
NON HAZARDOUS
CERTIFIED PRODUCT
IMPORTANT: The performance of the product is
dependent upon correct application onto surfaces
for which it is intended. Product to be applied
strictly in accordance with instructions onto
correctly prepared surfaces, which shall remain
sound, stable and free of cracking or movement.
Deviation from application instructions may
diminish or negate the performance of product.
Under no circumstances will the company be
liable for any loss, consequential or otherwise,
arising from the use of the product. Should this
product be proved defective our liability shall
be limited to the replacement of the product.
ALWAYS TEST ADHERE if in doubt. We
reserve the right to amend specifications and
applications techniques without prior notice. If
in doubt, contact the manufacturer.
Safe Use and First Aid.
AMI membranes are safe waterbased products
however, avoid contact with the skin and eyes,
use goggles and gloves at all times. Do not
induce vomiting if product is ingested, flush
eyes thoroughly for at least 15 minutes with
clean water. Give water to drink and seek
medical assistance. The use of gloves and eye
protection is always recommended.
Use the product in accordance with good
industrial procedures.
Australian Membrane Industries Pty Ltd
PO BOX 242 GLENORIE NSW 2157 AUSTRALIA
Phone:1800 099 990 [email protected]
Fax: 61 2 9652 0411 www.amimembraneindustries.com.au
XRAQUATHANE
CERTIFIED WET AREA MEMBRANEAQUATHANE
XR
ULTRA FLEXUltra Flex is a polyurethane blend membrane with CSIRO tested (4522) certification of Class III. Ultra Flex is UV resistant. Ultra Flex is a unique membrane which can be used in wet areas as a certified wet area membrane and externally, as a UV resistant membrane which is also suitable as a roof membrane.
Ultra Flex is available in light and dark grey with or without reinforcement.
Priming System: GP Primer (wet areas) – Sealpoxy - Hydrostatic Epoxy (for all roof applications).
Priming System: GP Primer – Sealpoxy
Available in 5 litre and 15 litre pails. 1800 099 990RX3 RX3
IMPORTANT: The performance of the product is
dependent upon correct application onto surfaces
for which it is intended. Product to be applied
strictly in accordance with instructions onto
correctly prepared surfaces, which shall remain
sound, stable and free of cracking or movement.
Deviation from application instructions may
diminish or negate the performance of product.
Under no circumstances will the company be
liable for any loss, consequential or otherwise,
arising from the use of the product. Should this
product be proved defective our liability shall
be limited to the replacement of the product.
ALWAYS TEST ADHERE if in doubt. We
reserve the right to amend specifications and
applications techniques without prior notice. If
in doubt, contact the manufacturer.
POLYURETHANE MEMBRANE
ULTRA FLEX
Safe Use and First Aid.
AMI membranes are safe waterbased products
however, avoid contact with the skin and eyes,
use goggles and gloves at all times. Do not
induce vomiting if product is ingested, flush
eyes thoroughly for at least 15 minutes with
clean water. Give water to drink and seek
medical assistance. The use of gloves and eye
protection is always recommended.
Use the product in accordance with good
industrial procedures.
Australian Membrane Industries Pty Ltd
PO BOX 242 GLENORIE NSW 2157 AUSTRALIA
Phone:1800 099 990 [email protected]
Fax: 61 2 9652 0411 www.amimembraneindustries.com.au
NON HAZARDOUS
CERTIFIED PRODUCT
ULTRA FLEX
ULTRA FLEX FAST CUREA special fast cure version of Ultra Flex that cures up to 60% faster than the standard product. Excellent for below ground and cold regions where waterbased membranes struggle to dry. Fast Cure
PU10Polyurethane/acrylic blend membrane which shows excellent application characteristics. The membrane is CSIRO certified as a Class III membrane. It is UV resistant and can also be used externally (covered or uncovered), or as a roof membrane.
Priming System: GP Primer – Sealpoxy
Available in 15 litre pails (blue).
1800 099 990
IMPORTANT: The performance of the product is
dependent upon correct application onto surfaces
for which it is intended. Product to be applied
strictly in accordance with instructions onto
correctly prepared surfaces, which shall remain
sound, stable and free of cracking or movement.
Deviation from application instructions may
diminish or negate the performance of product.
Under no circumstances will the company be
liable for any loss, consequential or otherwise,
arising from the use of the product. Should this
product be proved defective our liability shall
be limited to the replacement of the product.
ALWAYS TEST ADHERE if in doubt. We
reserve the right to amend specifications and
applications techniques without prior notice. If
in doubt, contact the manufacturer.
CLASS III WATERPROOFING POLYURETHANE MEMBRANE
PU 10
Safe Use and First Aid.
AMI membranes are safe waterbased products
however, avoid contact with the skin and eyes,
use goggles and gloves at all times. Do not
induce vomiting if product is ingested, flush
eyes thoroughly for at least 15 minutes with
clean water. Give water to drink and seek
medical assistance. The use of gloves and eye
protection is always recommended.
Use the product in accordance with good
industrial procedures.
Australian Membrane Industries Pty Ltd
PO BOX 242 GLENORIE NSW 2157 AUSTRALIA
Phone:1800 099 990 [email protected]
Fax: 61 2 9652 0411 www.amimembraneindustries.com.au
NON HAZARDOUS
CERTIFIED PRODUCT
PU 10
HYPER FLEXHyper Flex is a waterbased urethane membrane of exceptional quality which exceeds the performance of Ultra Flex. The product is both internal and external capable and is available in light grey.
1800 099 990
IMPORTANT: The performance of the product is
dependent upon correct application onto surfaces
for which it is intended. Product to be applied
strictly in accordance with instructions onto
correctly prepared surfaces, which shall remain
sound, stable and free of cracking or movement.
Deviation from application instructions may
diminish or negate the performance of product.
Under no circumstances will the company be
liable for any loss, consequential or otherwise,
arising from the use of the product. Should this
product be proved defective our liability shall
be limited to the replacement
of the product.
ALWAYS TEST ADHERE if in
doubt. We reserve the right to
amend specifications and
applications techniques
without prior notice. If
in doubt, contact the
manufacturer.
POLYURETHANE MEMBRANE
HYPER FLEX
Safe Use and First Aid.
AMI membranes are safe waterbased products
however, avoid contact with the skin and eyes,
use goggles and gloves at all times. Do not
induce vomiting if product is ingested, flush
eyes thoroughly for at least 15 minutes with
clean water. Give water to drink and seek
medical assistance. The use of gloves and eye
protection is always recommended.
Use the product in accordance with good
industrial procedures.
Australian Membrane Industries Pty Ltd
PO BOX 242 GLENORIE NSW 2157 AUSTRALIA
Phone:1800 099 990 [email protected]
Fax: 61 2 9652 0411 www.amimembraneindustries.com.au
NON HAZARDOUS
CERTIFIED PRODUCT
HYPER FLEX
LIGHT
GREY
15 LITRES
4
WET AREA MEMBRANES
AUSTRALIAN MEMBRANE INDUSTRIES - 1800 099 990
AMI TRADEAMI Trade is an acrylic resin blend wet area membrane which also has moderate UV resistance. The product is designed for tradesmen as an easy to apply, fast drying inexpensive membrane. AMI Trade conforms to AS4858.
Priming System: GP Primer – Sealpoxy
Available in dark grey in 15 litre pails.
1800 099 990
NON HAZARDOUS
CERTIFIED PRODUCT
IMPORTANT: The performance of the product is
dependent upon correct application onto surfaces
for which it is intended. Product to be applied
strictly in accordance with instructions onto
correctly prepared surfaces, which shall remain
sound, stable and free of cracking or movement.
Deviation from application instructions may
diminish or negate the performance of product.
Under no circumstances will the company be
liable for any loss, consequential or otherwise,
arising from the use of the product. Should this
product be proved defective our liability shall
be limited to the replacement of the product.
ALWAYS TEST ADHERE if in doubt. We
reserve the right to amend specifications and
applications techniques without prior notice. If
in doubt, contact the manufacturer.
APPLICATOR DESIGNED MEMBRANE
Safe Use and First Aid.
AMI membranes are safe waterbased products
however, avoid contact with the skin and eyes,
use goggles and gloves at all times. Do not
induce vomiting if product is ingested, flush
eyes thoroughly for at least 15 minutes with
clean water. Give water to drink and seek
medical assistance. The use of gloves and eye
protection is always recommended.
Use the product in accordance with good
industrial procedures.
15 LITRESAMI TRADE
Australian Membrane Industries Pty Ltd
PO BOX 242 GLENORIE NSW 2157 AUSTRALIA
Phone:1800 099 990 [email protected]
Fax: 61 2 9652 0411 www.amimembraneindustries.com.au
AMI TRADE
15 LITRES
P-96P96 is an inexpensive Class II reinforced CSIRO certified membrane which is suitable for wet area waterproofing as well as retaining walls (black). The membrane is SBR based, non UV and extremely fast drying. P96 will not bleach colour when used on retaining walls. The membrane is available in Black, Green and Grey colours.
Priming System: GP Primer – Sealpoxy - Hydrostatic Epoxy.
Available in 5 litre and 15 litre pails.
AMI AC SUPAFASTAMI SupaFast is a wet area membrane that conforms to AS4858 and is also UV resistant. and can be applied externally without the need of a covering top coat. The product is fast drying and designed for one coat application on shower walls.
The product offers significant economical advantages over other membranes.
Priming System: GP Primer – Sealpoxy
Available in 15 litre pails, grey colour.
1800 099 990
NON HAZARDOUS
CERTIFIED PRODUCT
Australian Membrane Industries Pty Ltd
PO BOX 242 GLENORIE NSW 2157 AUSTRALIA
Phone:1800 099 990 [email protected]
Fax: 61 2 9652 0411 www.amimembraneindustries.com.au
IMPORTANT: The performance of the product is
dependent upon correct application onto surfaces
for which it is intended. Product to be applied
strictly in accordance with instructions onto
correctly prepared surfaces, which shall remain
sound, stable and free of cracking or movement.
Deviation from application instructions may
diminish or negate the performance of product.
Under no circumstances will the company be
liable for any loss, consequential or otherwise,
arising from the use of the product. Should this
product be proved defective our liability shall
be limited to the replacement of the product.
ALWAYS TEST ADHERE if in doubt. We
reserve the right to amend specifications and
applications techniques without prior notice. If
in doubt, contact the manufacturer.
Safe Use and First Aid.
AMI membranes are safe waterbased products
however, avoid contact with the skin and eyes,
use goggles and gloves at all times. Do not
induce vomiting if product is ingested, flush
eyes thoroughly for at least 15 minutes with
clean water. Give water to drink and seek
medical assistance. The use of gloves and eye
protection is always recommended.
Use the product in accordance with good
industrial procedures.
FAST DRYING WATERPROOFING MEMBRANE
AC SupaFast
AC SupaFast
1800 099 990Australian Membrane Industries Pty Ltd
PO BOX 242 GLENORIE NSW 2157 AUSTRALIA
Phone:1800 099 990 [email protected]
Fax: 61 2 9652 0411 www.amimembraneindustries.com.au
IMPORTANT: The performance of the product is
dependent upon correct application onto surfaces
for which it is intended. Product to be applied
strictly in accordance with instructions onto
correctly prepared surfaces, which shall remain
sound, stable and free of cracking or movement.
Deviation from application instructions may
diminish or negate the performance of product.
Under no circumstances will the company be
liable for any loss, consequential or otherwise,
arising from the use of the product. Should this
product be proved defective our liability shall
be limited to the replacement of the product.
ALWAYS TEST ADHERE if in doubt. We
reserve the right to amend specifications and
applications techniques without prior notice. If
in doubt, contact the manufacturer.
Safe Use and First Aid.
AMI membranes are safe waterbased products
however, avoid contact with the skin and eyes,
use goggles and gloves at all times. Do not
induce vomiting if product is ingested, flush
eyes thoroughly for at least 15 minutes with
clean water. Give water to drink and seek
medical assistance. The use of gloves and eye
protection is always recommended.
Use the product in accordance with good
industrial procedures.
FAST DRYING WATERBASED URETHANE/ACRYLIC
AC10 SupaFast
NON HAZARDOUS
CERTIFIED PRODUCT
AC10 SupaFast
AMI AC10 SUPAFASTAMI AC10 SupaFast is a polyurethane modified AC SupaFast. The additional urethane additive upgrades the membrane significantly and renders the product stronger and more resilient. The membrane can be used externally without a covering top coat. AMI AC10 SupaFast is fast drying and economical to use and covers walls in one coat.
Priming System: GP Primer – Sealpoxy
Available in 15 litre pails, grey colour.
5
POLYURETHANE MEMBRANE, ROOF & EXTERNAL MEMBRANES
AUSTRALIAN MEMBRANE INDUSTRIES - 1800 099 990
Polyurethane Membrane
AMI PU 100SSelf levelling polyurethane membrane which is CSIRO certified as a Class III membrane. AMI PU 100 is not UV resistant. The product is a single pack moisture curing urethane membrane which when cured forms a strong pliable membrane.
Priming System: GP Primer – Sealpoxy
Available in grey. 15 Litre metal pails
1800 099 990
IMPORTANT: The performance of the product is
dependent upon correct application onto surfaces
for which it is intended. Product to be applied
strictly in accordance with instructions onto
correctly prepared surfaces, which shall remain
sound, stable and free of cracking or movement.
Deviation from application instructions may
diminish or negate the performance of product.
Under no circumstances will the company be
liable for any loss, consequential or otherwise,
arising from the use of the product. Should this
product be proved defective our liability shall
be limited to the replacement of the product.
ALWAYS TEST ADHERE if in doubt. We
reserve the right to amend specifications and
applications techniques without prior notice. If
in doubt, contact the manufacturer.
POLYURETHANE MEMBRANE
AMI PU 100S
AMI PU 100S
Safe Use and First Aid.
Avoid contact with skin and eyes, use goggles
and gloves at all times. Do not induce vomiting
if the product is ingested. Flush eyes
throughly for at least 15 minutes with clean
water. Seek medical assistance.
Use the product in accordance with AMI
application protocols and good industrial
procedures.
Australian Membrane Industries Pty Ltd
PO BOX 242 GLENORIE NSW 2157 AUSTRALIA
Phone:1800 099 990 [email protected]
Fax: 61 2 9652 0411 www.amimembraneindustries.com.au
WARNING
keep out of reach of children
AMI PU115VPolyurethane single pack moisture curing membrane (Vertical), which is designed not to sag when applied on (vertical) walls. The product is CSIRO certified as a Class III membrane. AMI PU115V is not UV resistant.
Priming System: SB Primer – Hydrostatic Epoxy.
Available in grey. 15 Litre metal pails
1800 099 990
Safe Use and First Aid.
Avoid contact with skin and eyes, use goggles
and gloves at all times. Do not induce vomiting
if the product is ingested. Flush eyes
throughly for at least 15 minutes with clean
water. Seek medical assistance.
Use the product in accordance with AMI
application protocols and good industrial
procedures.
IMPORTANT: The performance of the product is
dependent upon correct application onto surfaces
for which it is intended. Product to be applied
strictly in accordance with instructions onto
correctly prepared surfaces, which shall remain
sound, stable and free of cracking or movement.
Deviation from application instructions may
diminish or negate the performance of product.
Under no circumstances will the company be
liable for any loss, consequential or otherwise,
arising from the use of the product. Should this
product be proved defective our liability shall
be limited to the replacement of the product.
ALWAYS TEST ADHERE if in doubt. We
reserve the right to amend specifications and
applications techniques without prior notice. If
in doubt, contact the manufacturer.
POLYURETHANE MEMBRANE
AMI PU 115V
AMI PU 115V
Australian Membrane Industries Pty Ltd
PO BOX 242 GLENORIE NSW 2157 AUSTRALIA
Phone:1800 099 990 [email protected]
Fax: 61 2 9652 0411 www.amimembraneindustries.com.au
WARNING
keep out of reach of children
ULTRA FLEX TOP COATTop coat designed to overcoat Ultra Flex Traffic in situations where furniture will be situated on the membrane and where the membrane will be subjected to significant traffic. The top enables Ultra Flex Traffic to handle heavy traffic and furniture lodgement on the membrane without damage. The top coat is recommended where the membrane will be subject to heavy pedestrian traffic.
ULTRA FLEX TRAFFICUltra Flex Traffic is a high quality waterbased external UV resistant membrane that is lightly pedestrian trafficable in standard form. Ultra Flex Traffic is unique in that it is cost and performance effective when compared to solvent based polyurethanes. The product needs protective top coat if furniture is to placed on membrane. Coupled with a range of aggregates, Ultra Flex Traffic can be over coated with AMI’s two pack urethanes and dressed in a range of aggregates to provide a very strong and attractive surface. All AMI top coats extend the warranty and longevity of the membrane.
Priming System: Sealpoxy – Hydrostatic Epoxy.
Available in 5 litre and 15 litre pails, light grey1800 099 990
IMPORTANT: The performance of the product is
dependent upon correct application onto surfaces
for which it is intended. Product to be applied
strictly in accordance with instructions onto
correctly prepared surfaces, which shall remain
sound, stable and free of cracking or movement.
Deviation from application instructions may
diminish or negate the performance of product.
Under no circumstances will the company be
liable for any loss, consequential or otherwise,
arising from the use of the product. Should this
product be proved defective our liability shall
be limited to the replacement of the product.
ALWAYS TEST ADHERE if in doubt. We
reserve the right to amend specifications and
applications techniques without prior notice. If
in doubt, contact the manufacturer.
POLYURETHANE TRAFFICABLE MEMBRANE
Safe Use and First Aid.
AMI membranes are safe waterbased products
however, avoid contact with the skin and eyes,
use goggles and gloves at all times. Do not
induce vomiting if product is ingested, flush
eyes thoroughly for at least 15 minutes with
clean water. Give water to drink and seek
medical assistance. The use of gloves and eye
protection is always recommended.
Use the product in accordance with good
industrial procedures.
Australian Membrane Industries Pty Ltd
PO BOX 242 GLENORIE NSW 2157 AUSTRALIA
Phone:1800 099 990 [email protected]
Fax: 61 2 9652 0411 www.amimembraneindustries.com.au
ULTRA FLEX
ULTRA FLEX
TRAFFICTRAFFIC
NON HAZARDOUS
CERTIFIED PRODUCT
Roof & External Membranes
1800 099 990Australian Membrane Industries Pty Ltd
PO BOX 242 GLENORIE NSW 2157 AUSTRALIA
Phone:1800 099 990 [email protected]
Fax: 61 2 9652 0411 www.amimembraneindustries.com.au
IMPORTANT: The performance of the product is
dependent upon correct application onto surfaces
for which it is intended. Product to be applied
strictly in accordance with instructions onto
correctly prepared surfaces, which shall remain
sound, stable and free of cracking or movement.
Deviation from application instructions may
diminish or negate the performance of product.
Under no circumstances will the company be
liable for any loss, consequential or otherwise,
arising from the use of the product. Should this
product be proved defective our liability shall
be limited to the replacement of the product.
ALWAYS TEST ADHERE if in doubt. We
reserve the right to amend specifications and
applications techniques without prior notice. If
in doubt, contact the manufacturer.
Safe Use and First Aid.
AMI membranes are safe waterbased products
however, avoid contact with the skin and eyes,
use goggles and gloves at all times. Do not
induce vomiting if product is ingested, flush
eyes thoroughly for at least 15 minutes with
clean water. Give water to drink and seek
medical assistance. The use of gloves and eye
protection is always recommended.
Use the product in accordance with good
industrial procedures.
ULTRA FLEX SEALER
NON HAZARDOUS
CERTIFIED PRODUCT
15 Litres
TOP COATULTRA FLEX
TOP COATULTRA FLEX
6
POLYURETHANE MEMBRANE, ROOF & EXTERNAL MEMBRANES
AUSTRALIAN MEMBRANE INDUSTRIES - 1800 099 990
ULTRA FLEX 50 / 75 Ultra Flex 50 / 75 are aliphatic waterbased urethane membranes of unparalleled performance and trafficable applications. These special membranes are made to order and are used in areas where superior performance from the membrane is required due to adverse environmental conditions. For further information, contact AMI.
Priming system will be determined by the application.
Available in 15 litre pails only.
1800 099 990
NON HAZARDOUS
CERTIFIED PRODUCT
IMPORTANT: The performance of the product is
dependent upon correct application onto surfaces
for which it is intended. Product to be applied
strictly in accordance with instructions onto
correctly prepared surfaces, which shall remain
sound, stable and free of cracking or movement.
Deviation from application instructions may
diminish or negate the performance of product.
Under no circumstances will the company be
liable for any loss, consequential or otherwise,
arising from the use of the product. Should this
product be proved defective our liability shall
be limited to the replacement of the product.
ALWAYS TEST ADHERE if in doubt. We
reserve the right to amend specifications and
applications techniques without prior notice. If
in doubt, contact the manufacturer.
Safe Use and First Aid.
AMI membranes are safe waterbased products
however, avoid contact with the skin and eyes,
use goggles and gloves at all times. Do not
induce vomiting if product is ingested, flush
eyes thoroughly for at least 15 minutes with
clean water. Give water to drink and seek
medical assistance. The use of gloves and eye
protection is always recommended.
Use the product in accordance with good
industrial procedures.
Australian Membrane Industries Pty Ltd
PO BOX 242 GLENORIE NSW 2157 AUSTRALIA
Phone:1800 099 990 [email protected]
Fax: 61 2 9652 0411 www.amimembraneindustries.com.au
50ULTRA FLEX
ULTRA FLEX
POLYURETHANE MEMBRANE50
AMI ULTRA FLEX ACRYLIC PLUSAMI Ultra Flex Acrylic Plus is an acrylic roof membrane. The product is UV resistant and incorporates inhibitor chemicals to stop fungal growth. Ultra Flex Acrylic Plus can be used as the first coat in Heat Block applications thereby reducing application costs significantly. The product can be tinted as required and applied as a waterproofing and cosmetic upgrade of any roof. Ultra Flex Acrylic Plus, with or without fibres is available in a light grey in 15 litre pails.
Priming System: Sealpoxy
Available in 15 Litre pails.
1800 099 990
NON HAZARDOUS
CERTIFIED PRODUCT
IMPORTANT: The performance of the product is
dependent upon correct application onto surfaces
for which it is intended. Product to be applied
strictly in accordance with instructions onto
correctly prepared surfaces, which shall remain
sound, stable and free of cracking or movement.
Deviation from application instructions may
diminish or negate the performance of product.
Under no circumstances will the company be
liable for any loss, consequential or otherwise,
arising from the use of the product. Should this
product be proved defective our liability shall
be limited to the replacement of the product.
ALWAYS TEST ADHERE if in doubt. We
reserve the right to amend specifications and
applications techniques without prior notice. If
in doubt, contact the manufacturer.
WATERPROOFING MEMBRANE
Safe Use and First Aid.
AMI membranes are safe waterbased products
however, avoid contact with the skin and eyes,
use goggles and gloves at all times. Do not
induce vomiting if product is ingested, flush
eyes thoroughly for at least 15 minutes with
clean water. Give water to drink and seek
medical assistance. The use of gloves and eye
protection is always recommended.
Use the product in accordance with good
industrial procedures.
ACRYLIC PLUSULTRA FLEX
ULTRA FLEX
ACRYLIC PLUS
Australian Membrane Industries Pty Ltd
PO BOX 242 GLENORIE NSW 2157 AUSTRALIA
Phone:1800 099 990 [email protected]
Fax: 61 2 9652 0411 www.amimembraneindustries.com.au
1800 099 990
NON HAZARDOUS
CERTIFIED PRODUCT
IMPORTANT: The performance of the product is
dependent upon correct application onto surfaces
for which it is intended. Product to be applied
strictly in accordance with instructions onto
correctly prepared surfaces, which shall remain
sound, stable and free of cracking or movement.
Deviation from application instructions may
diminish or negate the performance of product.
Under no circumstances will the company be
liable for any loss, consequential or otherwise,
arising from the use of the product. Should this
product be proved defective our liability shall
be limited to the replacement of the product.
ALWAYS TEST ADHERE if in doubt. We
reserve the right to amend specifications and
applications techniques without prior notice. If
in doubt, contact the manufacturer.
Safe Use and First Aid.
AMI membranes are safe waterbased products
however, avoid contact with the skin and eyes,
use goggles and gloves at all times. Do not
induce vomiting if product is ingested, flush
eyes thoroughly for at least 15 minutes with
clean water. Give water to drink and seek
medical assistance. The use of gloves and eye
protection is always recommended.
Use the product in accordance with good
industrial procedures.
Australian Membrane Industries Pty Ltd
PO BOX 242 GLENORIE NSW 2157 AUSTRALIA
Phone:1800 099 990 [email protected]
Fax: 61 2 9652 0411 www.amimembraneindustries.com.au
BLOCKAMI HEAT
BLOCKPOLYURETHANE MEMBRANE
AMI HEAT
HEAT BLOCKHeat Block is a high build elastomeric UV resistant heat re-radiating membrane which incorporates additives which provide remarkable insulation properties, with tested reports during excessive temperature periods of internal temperature being lowered by 8 - 10 degrees C.
Heat Block also retards fires and stops fire damage as the product re-radiates the heat. There are examples of Heat Block painted sheds which suffered bush fire events, which were left untouched by the fire. The product has not yet been tested in this area.
Heat Block has excellent flexibility and bridging capability. The matt finish alleviates glare. For a smooth finish, if required, a sealer coat is available from AMI. Heat Block can be tinted within a narrow range of light colours.
The advantages of Heat Block are significant, from reducing running costs of air conditioning systems through a significant reduction in internal building heat. The product stops roof heat banks from developing by stopping heat transfer through the roof into the building.
Priming System – Sealpoxy – Hydrostatic Epoxy.
Available in 15 litre pails.
7
POLYURETHANE MEMBRANE, ROOF & EXTERNAL MEMBRANES
AUSTRALIAN MEMBRANE INDUSTRIES - 1800 099 990
HOW DOES HEAT BLOCK WORK?The easiest way to explain this is to say that Heat Block works exactly opposite to the way the black coating now used as a selective surface on solar water heater panels (chrome black) works. Chrome black absorbs 95% of the sun’s shorter wavelength radiant energy, and limits emission to only 9% of the longer infrared wavelength energy from the collector surface. Hence, very little of the heat that is gained is then lost through emissivity. Because of this selectivity, the chrome black surface may get hotter than the air temperature by 100 degrees Celsius or more.
By contrast, the Heat Block product absorbs only15% of the sun’s heat and is especially good at re-emitting most of this absorbed energy away from the treated surface (over 95%). The end result is that the exterior surface only gets to about 5 degrees Celsius hotter than the ambient air temperature. This compares with an untreated exterior surface that gets 10 – 20 degrees Celsius hotter.
Solarreflectance
Thermalemissivity
Incidentsolar
radiation
Insulation
heat load(R value)
Temp gradient
(1- (å)á)
Solarreflectance
Thermalemissivity
Incidentsolar
radiation
heat load
(å)(1-á)
Heat Block
solar reflectance High + thermal emissivity High
lower heat load + cooler surfaces
lower air conditioning costs
Heat Block
Airconditioning is required to slow the rate of heat penetration
Heat penetration into a structure is mainly determined by just two factors:
1) The temperature gradient between the hot external surfaces and the cooler interior walls, and
2) The insulating capacity (R value) of the structure.
The two approaches to comfortable living
Insulation works by slowing down heat flow from the hot exterior surfaces to the coolerinterior.
Heat Block works by reducing the temperature gradient through selective surface cooling.
Heat Block
Selective Surface Cooling
The surface cooling achieved by Heat Blockis
due to two remarkable properties:
1) Its low absorptance of solar radiation, suchthat 85% of solar radiation is reflected, and
2) Its high emissivity of thermal energy, suchthat over 95% of absorbed heat is re-emitted.
Heat Block
HOW DOES HEAT BLOCK WORK?
Solarreflectance
Thermalemissivity
Incidentsolar
radiation
Insulation
heat load(R value)
Temp gradient
(1- (å)á)
Solarreflectance
Thermalemissivity
Incidentsolar
radiation
heat load
(å)(1-á)
Heat Block
solar reflectance High + thermal emissivity High
lower heat load + cooler surfaces
lower air conditioning costs
Heat Block
Airconditioning is required to slow the rate of heat penetration
Heat penetration into a structure is mainly determined by just two factors:
1) The temperature gradient between the hot external surfaces and the cooler interior walls, and
2) The insulating capacity (R value) of the structure.
The two approaches to comfortable living
Insulation works by slowing down heat flow from the hot exterior surfaces to the coolerinterior.
Heat Block works by reducing the temperature gradient through selective surface cooling.
Heat Block
Selective Surface Cooling
The surface cooling achieved by Heat Blockis
due to two remarkable properties:
1) Its low absorptance of solar radiation, suchthat 85% of solar radiation is reflected, and
2) Its high emissivity of thermal energy, suchthat over 95% of absorbed heat is re-emitted.
Heat Block
8
POLYURETHANE MEMBRANE, ROOF & EXTERNAL MEMBRANES
AUSTRALIAN MEMBRANE INDUSTRIES - 1800 099 990
S420 THERMALThermal stopping membrane designed to be applied under the S400 membrane and over Ultra Flex to provide exceptional thermal blocking under the S400 Silicone membrane as a system that offers unsurpassed warranty options. The product is trowel applied.
Available in 15 litre pails, light grey.
Contact AMI for more details.
1800 099 99015 Litres
IMPORTANT: The performance of the product is
dependent upon correct application onto surfaces
for which it is intended. Product to be applied
strictly in accordance with instructions onto
correctly prepared surfaces, which shall remain
sound, stable and free of cracking or movement.
Deviation from application instructions may
diminish or negate the performance of product.
Under no circumstances will the company be
liable for any loss, consequential or otherwise,
arising from the use of the product. Should this
product be proved defective our liability shall
be limited to the replacement of the product.
ALWAYS TEST ADHERE if in doubt. We
reserve the right to amend specifications and
applications techniques without prior notice. If
in doubt, contact the manufacturer.
ROOF THERMAL HEAT BANK BARRIER
S420 THERMAL
Safe Use and First Aid.
AMI membranes are safe waterbased products
however, avoid contact with the skin and eyes,
use goggles and gloves at all times. Do not
induce vomiting if product is ingested, flush
eyes thoroughly for at least 15 minutes with
clean water. Give water to drink and seek
medical assistance. The use of gloves and eye
protection is always recommended.
Use the product in accordance with good
industrial procedures.
Australian Membrane Industries Pty Ltd
PO BOX 242 GLENORIE NSW 2157 AUSTRALIA
Phone:1800 099 990 [email protected]
Fax: 61 2 9652 0411 www.amimembraneindustries.com.au
NON HAZARDOUS
CERTIFIED PRODUCT
S420 THERMAL
S400S400 is a unique silicone membrane roof membrane which is not affected by UV or pooling water. It is suitable for flat roof repairs and offers a very long warranty (20 – 25 years) if undertaken under direction of AMI. S400 is also used to refurbish old and damaged torch on membrane rendering the application with a long term warranty.
Priming System: Hydrostatic Epoxy
Colour – light grey
Available in 15 litre pails.
Contact AMI for more details.1800 099 990
IMPORTANT: The performance of the product is
dependent upon correct application onto surfaces
for which it is intended. Product to be applied
strictly in accordance with instructions onto
correctly prepared surfaces, which shall remain
sound, stable and free of cracking or movement.
Deviation from application instructions may
diminish or negate the performance of product.
Under no circumstances will the company be
liable for any loss, consequential or otherwise,
arising from the use of the product. Should this
product be proved defective our liability shall
be limited to the replacement of the product.
ALWAYS TEST ADHERE if in doubt. We
reserve the right to amend specifications and
applications techniques without prior notice. If
in doubt, contact the manufacturer.
SILICONE MEMBRANEAMI S400
Safe Use and First Aid.
AMI membranes are safe waterbased products
however, avoid contact with the skin and eyes,
use goggles and gloves at all times. Do not
induce vomiting if product is ingested, flush
eyes thoroughly for at least 15 minutes with
clean water. Give water to drink and seek
medical assistance. The use of gloves and eye
protection is always recommended.
Use the product in accordance with good
industrial procedures.
Australian Membrane Industries Pty Ltd
PO BOX 242 GLENORIE NSW 2157 AUSTRALIA
Phone:1800 099 990 [email protected]
Fax: 61 2 9652 0411 www.amimembraneindustries.com.au
NON HAZARDOUS
CERTIFIED PRODUCT
AMI S400
FROM THIS
TO THIS
AMI S400 Roofing System
1. HydroStatic Epoxy2. Ultra Flex (Water based polyurethane)3. S420 Thermal Block Membrane4. S400 Silicone Membrane
= 20/25 year warranty
1800 099 990 [email protected] www.amimembraneindustries.com.au
Special Roof Membranes
9
PLANTER BOXES, RETAINING WALLS AND SPECIAL MEMBRANES
AUSTRALIAN MEMBRANE INDUSTRIES - 1800 099 990
AMI BLACK FLEX 200Latex/bitumen membrane specifically designed for waterproofing planter boxes and retaining walls. The product does not need priming and is applied in two coats to achieve the desire result.
The product does not require priming.
Available in 15 litre pails.
1800 099 99015 Litres
NON HAZARDOUS
CERTIFIED PRODUCT
IMPORTANT: The performance of the product is
dependent upon correct application onto surfaces
for which it is intended. Product to be applied
strictly in accordance with instructions onto
correctly prepared surfaces, which shall remain
sound, stable and free of cracking or movement.
Deviation from application instructions may
diminish or negate the performance of product.
Under no circumstances will the company be
liable for any loss, consequential or otherwise,
arising from the use of the product. Should this
product be proved defective our liability shall
be limited to the replacement of the product.
ALWAYS TEST ADHERE if in doubt. We
reserve the right to amend specifications and
applications techniques without prior notice. If
in doubt, contact the manufacturer.
Safe Use and First Aid.
AMI membranes are safe waterbased products
however, avoid contact with the skin and eyes,
use goggles and gloves at all times. Do not
induce vomiting if product is ingested, flush
eyes thoroughly for at least 15 minutes with
clean water. Give water to drink and seek
medical assistance. The use of gloves and eye
protection is always recommended.
Use the product in accordance with good
industrial procedures.
Australian Membrane Industries Pty Ltd
PO BOX 242 GLENORIE NSW 2157 AUSTRALIA
Phone:1800 099 990 [email protected]
Fax: 61 2 9652 0411 www.amimembraneindustries.com.au
FLEX 200AMI BLACK
BLACK LATEX/BITUMEN MEMBRANEAMI BLACK
FLEX 200
Planter Boxes & Retaining Walls
Special Membranes
TWO PACK MEMBRANEAMI UG3 is a two pack, 100% solids, industrial strength (polyurethane) semi rigid (fast cure) membrane designed for bridge decks, ramps, multi-level car parks, roof tops and any area requiring an industrial strength, fast cure two pack membrane. The product can be applied in any thickness, in one application and cures to a trafficable state within 4 hours or can be top coated with a topping such as asphalt thereby markedly reducing downtime and allowing critical areas such as bridge decks to be opened sooner. This system can also be used in conjunction with a wide range of abrasive aggregates of various sizes depending upon the type of traffic anticipated, thereby rendering the membrane a trafficable system for vehicle and heavy industrial traffic.
Priming System: Hydrostatic Epoxy only.
Available as a 15kg kit (10kgs part A and 5 kgs Part B)
Colour neutral. 1800 099 990Australian Membrane Industries Pty Ltd
PO BOX 242 GLENORIE NSW 2157 AUSTRALIA
Phone:1800 099 990 [email protected]
Fax: 61 2 9652 0411 www.amimembraneindustries.com.au
IMPORTANT: The performance of the product is
dependent upon correct application onto surfaces
for which it is intended. Product to be applied
strictly in accordance with instructions onto
correctly prepared surfaces, which shall remain
sound, stable and free of cracking or movement.
Deviation from application instructions may
diminish or negate the performance of product.
Under no circumstances will the company be
liable for any loss, consequential or otherwise,
arising from the use of the product. Should this
product be proved defective our liability shall
be limited to the replacement of the product.
ALWAYS TEST ADHERE if in doubt. We
reserve the right to amend specifications and
applications techniques without prior notice. If
in doubt, contact the manufacturer.
Safe Use and First Aid.
AMI membranes are safe waterbased products
however, avoid contact with the skin and eyes,
use goggles and gloves at all times. Do not
induce vomiting if product is ingested, flush
eyes thoroughly for at least 15 minutes with
clean water. Give water to drink and seek
medical assistance. The use of gloves and eye
protection is always recommended.
Use the product in accordance with good
industrial procedures.
NON HAZARDOUS
CERTIFIED PRODUCT
15 KG
URETHANEUG3 2 PACK
URETHANEUG3 2 PACK
P96 BLACKThe ceramic content of this membrane makes it suitable for application in adverse areas such as planter boxes and retaining walls. P96 is very strong and was certified as a Class II membrane with reinforcement fibre.
Priming System: GP Primer – Sealpoxy
10
TOP COAT SEALER AND AMI PRIMERS
AUSTRALIAN MEMBRANE INDUSTRIES - 1800 099 990
Top Coat Sealer
AMI TOP COAT SEALER AND NON-SLIPWater based urethane top coat sealer for coatings and membranes such as Ultra Flex Traffic. The product can be manufactured with non-slip capability to render trafficable areas safe to walk on in most conditions. The product is UV resistant.
AMI top coat applications extend membrane warranties by 8 years after the initial application warranty has expired.
Available in 15 litre pails, light grey standard.
1800 099 990
SEALER
SEALER NON SLIP
BATCH
15 LITRES
Safe Use and First Aid.
AMI membranes are safe waterbased products,
however, avoid contact with the skin and eyes,
use goggles and gloves at all times. Do not
induce vomiting if product is ingested, flush
eyes thoroughly for at least 15 minutes with
clean water. Give water to drink and seek
medical assistance. The use of gloves and eye
protection is always recommended.
Use the product in accordance with good
industrial procedures.
IMPORTANT: The performance of the product is
dependent upon correct application onto surfaces
for which it is intended. Product to be applied
strictly in accordance with instructions onto
correctly prepared surfaces, which shall remain
sound, stable and free of cracking or movement.
Deviation from application instructions may
diminish or negate the performance of product.
Under no circumstances will the company be
liable for any loss, consequential or otherwise,
arising from the use of the product. Should this
product be proved defective our liability shall
be limited to the replacement of the product.
ALWAYS TEST ADHERE if in doubt. We
reserve the right to amend specifications and
applications techniques without prior notice. If
in doubt, contact the manufacturer.
Australian Membrane Industries Pty Ltd
PO BOX 242 GLENORIE NSW 2157 AUSTRALIA
Phone:1800 099 990 [email protected]
Fax: 61 2 9652 0411 www.amimembraneindustries.com.au
NON HAZARDOUS
CERTIFIED PRODUCT
AMI MEMBRANE
SEALERAMI MEMBRANE
SEALER
SB PRIMERSingle pack, low solids solvent based primer for higher substrate penetration generally but specifically designed for the wet area polyurethane membranes (PU100 and 115V).
Available in 15 Litre pails.
1800 099 99015 Litres
NON HAZARDOUS
CERTIFIED PRODUCT
IMPORTANT: The performance of the product is
dependent upon correct application onto surfaces
for which it is intended. Product to be applied
strictly in accordance with instructions onto
correctly prepared surfaces, which shall remain
sound, stable and free of cracking or movement.
Deviation from application instructions may
diminish or negate the performance of product.
Under no circumstances will the company be
liable for any loss, consequential or otherwise,
arising from the use of the product. Should this
product be proved defective our liability shall
be limited to the replacement of the product.
ALWAYS TEST ADHERE if in doubt. We
reserve the right to amend specifications and
applications techniques without prior notice. If
in doubt, contact the manufacturer.
Safe Use and First Aid.
AMI membranes are safe waterbased products
however, avoid contact with the skin and eyes,
use goggles and gloves at all times. Do not
induce vomiting if product is ingested, flush
eyes thoroughly for at least 15 minutes with
clean water. Give water to drink and seek
medical assistance. The use of gloves and eye
protection is always recommended.
Use the product in accordance with good
industrial procedures.
Australian Membrane Industries Pty Ltd
PO BOX 242 GLENORIE NSW 2157 AUSTRALIA
Phone:1800 099 990 [email protected]
Fax: 61 2 9652 0411 www.amimembraneindustries.com.au
SB PRIMERSB PRIMER
GP PRIMERSBR based single pack fast drying primer for wet areas only. Suitable for all AMI wet area membranes.
Available in 15 Litre and 5 Litre pails.
1800 099 990
GPSafe Use and First Aid.
AMI membranes are safe waterbased products
however, avoid contact with the skin and eyes,
use goggles and gloves at all times. Do not
induce vomiting if product is ingested, flush
eyes thoroughly for at least 15 minutes with
clean water. Give water to drink and seek
medical assistance. The use of gloves and eye
protection is always recommended.
Use the product in accordance with good
industrial procedures.
IMPORTANT: The performance of the product is
dependent upon correct application onto surfaces
for which it is intended. Product to be applied
strictly in accordance with instructions onto
correctly prepared surfaces, which shall remain
sound, stable and free of cracking or movement.
Deviation from application instructions may
diminish or negate the performance of product.
Under no circumstances will the company be
liable for any loss, consequential or otherwise,
arising from the use of the product. Should this
product be proved defective our liability shall
be limited to the replacement of the product.
ALWAYS TEST ADHERE if in doubt. We
reserve the right to amend specifications and
applications techniques without prior notice. If
in doubt, contact the manufacturer.
General purpose under tile wet primer AS3740
GP Primer
Australian Membrane Industries Pty Ltd
PO BOX 242 GLENORIE NSW 2157 AUSTRALIA
Phone:1800 099 990 [email protected]
Fax: 61 2 9652 0411 www.amimembraneindustries.com.au
NON HAZARDOUS
CERTIFIED PRODUCT
GP Primer
15 Litres
AMI Primers
GPSConcentrated SBR priming liquid suitable for priming and waterproofing screeds in various dilutions which are provided by AMI. This product can also be used to construct vehicle trafficable substrate 30 – 50mm as a trafficable screed.
Available in 15 Litre pails.
1800 099 990Australian Membrane Industries Pty Ltd
PO BOX 242 GLENORIE NSW 2157 AUSTRALIA
Phone:1800 099 990 [email protected]
Fax: 61 2 9652 0411 www.amimembraneindustries.com.au
IMPORTANT: The performance of the product is
dependent upon correct application onto surfaces
for which it is intended. Product to be applied
strictly in accordance with instructions onto
correctly prepared surfaces, which shall remain
sound, stable and free of cracking or movement.
Deviation from application instructions may
diminish or negate the performance of product.
Under no circumstances will the company be
liable for any loss, consequential or otherwise,
arising from the use of the product. Should this
product be proved defective our liability shall
be limited to the replacement of the product.
ALWAYS TEST ADHERE if in doubt. We
reserve the right to amend specifications and
applications techniques without prior notice. If
in doubt, contact the manufacturer.
Safe Use and First Aid.
AMI membranes are safe waterbased products
however, avoid contact with the skin and eyes,
use goggles and gloves at all times. Do not
induce vomiting if product is ingested, flush
eyes thoroughly for at least 15 minutes with
clean water. Give water to drink and seek
medical assistance. The use of gloves and eye
protection is always recommended.
Use the product in accordance with good
industrial procedures.
CONCENTRATED LATEX SOLUTION
GPS
NON HAZARDOUS
CERTIFIED PRODUCT
GPS
15 Litres
11
TOP COAT SEALER AND AMI PRIMERS
AUSTRALIAN MEMBRANE INDUSTRIES - 1800 099 990
HYDROSTATIC EPOXYHigh quality, high build hydrostatic epoxy designed to be used in areas where hydrostatic capability is required (below ground, retaining walls etc.). The product can be used as a primer/sealer in circumstances where lino needs to be laid over moisture free substrate.
20 litre kit (light grey)
10 litre kit
4 litre kit
2 litre kit
1 litre kit
1800 099 990
Water Based 2 Pack Epoxy
DESCRIPTION: AMI Hydrostatic EPOXY is a two pack water based epoxy primer designed as a high solids primer for critical waterproofing
and coating applications. See data sheet for further information.
MIXING INSTRUCTIONS: Use only with Part B of AMI’s Hydrostatic EPOXY. Thoroughly mix equal parts of Part A and Part B. Mixed product
should be used within one hour, recoat time 4 to 6 hours depending on ambient temperature and full cure 24 hours.
APPLICATION: Apply by brush, roller or airless spray system at 4 to 6 square metres per litre (see data sheet for specific volume requirement
for various applications). Ensure that the surface is sound, free of grime, grease, oil or wax like materials, standing or running water. If required,
a second coat can be applied after the first coat is touch dry.
CLEANING: Clean equipment immediately after use with clean water.
SHELF LIFE: One year.
HAZARDOUS:
• Contains 10-30% reaction product of epichlorohydrin and bisphenol A
• May cause skin sensitization
• Avoid contact with skin and eyes and avoid breathing vapours
• Wear gloves and eye protection when mixing or using this product
• First aid: for advice contact Poisons Information Centre (Australia 13 11 26
New Zealand 0800 764 766) or call a doctor. After contact with skin wash
with plenty of soap and water.
WARNING
KEEP OUT OF REACH OF CHILDREN
Australian Membrane Industries Pty Ltd
PO BOX 242 GLENORIE NSW 2157 AUSTRALIA
Phone:1800 099 990 [email protected]
Fax: 61 2 9652 0411 www.amimembraneindustries.com.au
PART A 10 LitresHydroStatic EPOXY
SCREED BLOCKA latex mixture used to waterproof sand / cement screeds. Once a screed is contaminated with water, it s almost impossible to dry. Good practice is to waterproof the screed as it is being laid.
Available in 15 litre pails.
SEALPOXYEpoxy Specifically designed for priming non-wet areas. Sealpoxy should be used as a primer if the area is to be tiled. The product is cost effective and necessary for all priming associated with non-wet area tiling and any wide expanse where tiling will be undertaken. Take the doubt out of any application, use Sealpoxy.
20 litre kit
Waterbased Epoxy
12
TOP COAT SEALER AND AMI PRIMERS
AUSTRALIAN MEMBRANE INDUSTRIES - 1800 099 990
AMI offers three types of sealants, two solvent based and a neutral sealant.
AMI SEAL 50 (600ML)
One component, moisture-cured polyurethane based sealant. After curing, it provides a permanent elastic bond to seal and fasten materials with different coefficient of expansion.
The product has low odour and is non-corrosive.
AMI SEAL FF550 (600ML)
Solvent based one component moisture curing low modulus polyurethane sealant with excellent joint movement capability. It cures to a flexible, durable and weather resistant sealant and exhibits excellent adhesion to a wide range of substrates.
AMI SEAL FF625 (600ML)
High performance, one component hybrid moisture curing construction sealant.
The product cures to form a seal that is tough, elastic and weatherproof with good chemical characteristics. FF625 is a low modulus product that is suited for situations that may experience significant expansion and contraction. Easy to apply and tool off.
AMI SEAL 50
AMI SEAL 50
y Highly Flexible
y Tear Resistant y Paintable
y Fast Curing
Australian Membrane Industries Pty Ltd
PO BOX 242 GLENORIE NSW 2157 AUSTRALIA
Phone:1800 099 990 [email protected]
Fax: 61 2 9652 0411 www.amimembraneindustries.com.au
600MLPOLYURETHANE SEALANT
Non-Slip Coating
ULTRA TUFF NON-SLIPWaterbased non-slip coating with 700-micron rubber aggregate. The product has been in production for over 20 years. Easy to apply and soft under foot. The rubber aggregate will not cause abrasion if anyone falls on the coating. The product is supplied in 15 litre pails and 5 lite pails.
Priming System: Hydrostatic Epoxy
Available in 15 and 5 litre pails
1800 099 990Australian Membrane Industries Pty Ltd
PO BOX 242 GLENORIE NSW 2157 AUSTRALIA
Phone:1800 099 990 [email protected]
Fax: 61 2 9652 0411 www.amimembraneindustries.com.au
IMPORTANT: The performance of the product is
dependent upon correct application onto surfaces
for which it is intended. Product to be applied
strictly in accordance with instructions onto
correctly prepared surfaces, which shall remain
sound, stable and free of cracking or movement.
Deviation from application instructions may
diminish or negate the performance of product.
Under no circumstances will the company be
liable for any loss, consequential or otherwise,
arising from the use of the product. Should this
product be proved defective our liability shall
be limited to the replacement of the product.
ALWAYS TEST ADHERE if in doubt. We
reserve the right to amend specifications and
applications techniques without prior notice. If
in doubt, contact the manufacturer.
Safe Use and First Aid.
AMI membranes are safe waterbased products
however, avoid contact with the skin and eyes,
use goggles and gloves at all times. Do not
induce vomiting if product is ingested, flush
eyes thoroughly for at least 15 minutes with
clean water. Give water to drink and seek
medical assistance. The use of gloves and eye
protection is always recommended.
Use the product in accordance with good
industrial procedures.
RUBBERISED NON-SLIP COATING
NON HAZARDOUS
CERTIFIED PRODUCT
15 Litres
ULTRA TUFF XS
ULTRA TUFF XS
AMI SEAL 50
AMI SEAL 50
y Highly Flexible
y Tear Resistant y Paintable
y Fast Curing
Australian Membrane Industries Pty Ltd
PO BOX 242 GLENORIE NSW 2157 AUSTRALIA
Phone:1800 099 990 [email protected]
Fax: 61 2 9652 0411 www.amimembraneindustries.com.au
600MLPOLYURETHANE SEALANT
AMI SEAL 50
AMI SEAL 50
y Highly Flexible
y Tear Resistant y Paintable
y Fast Curing
Australian Membrane Industries Pty Ltd
PO BOX 242 GLENORIE NSW 2157 AUSTRALIA
Phone:1800 099 990 [email protected]
Fax: 61 2 9652 0411 www.amimembraneindustries.com.au
600MLPOLYURETHANE SEALANT
Sealants
13
NSW
INGLEBURN
3 Moorlands Road, Ingleburn. 2565. NSW
P: (02) 9618 7040 F: (02) 9618 0134
SEVEN HILLS26 Powers Road, Seven Hills. 2147
P: 1800 099990 F: 61 2 9652 0411
WOLLONGONGIllawarra Industrial supplies.
8 – 10 Third Avenue, Unanderra. 2526
P: (02) 4271 7032
VICTORIATHE WATERSTOP SHOP20 Dalgety Street, Oakleigh. 3166
P: (03) 9569 7687
TASMANIA
TERRACE TRADING29 Lampton Ave, Derwent Park. 7009
P: (03) 6272 4327
QUEENSLAND
GEEBUNG
H2O WATERPROOFING SOLUTIONS
Unit 1/209 Robinson Road Geebung. 4034
P: (07) 3633 0482
GOLD COAST + SE QUEENSLAND AND NORTHERN NSW
SIMMCO WATERPROOFING SUPPLIES
P: (07) 56 657 186
NATIONAL Phone : 1800 099 990
Printed and Designed by Shiralee Martin - Minuteman Press Castle Hill