20140902 antenna alignment with theodolite, lasers and ... · antenna alignment with theodolite,...
TRANSCRIPT
Antenna Alignment with Theodolite, Lasers and Photogrammetry
Date: 02.09.2014
® 2010 sigma3D GmbH • www.sigma3D.de • [email protected]
3rd RadioNet3 European Radio Astronomy Technical Forum Workshop
Metrologies at Radio Astronomy Antennas, September 1-2, 2014, At the Department of Earth and Space Sciences, Chalmers University of Technology in Gothenburg, Sweden
Table of Content
2. Accuracy with mobile 3D "industrial" measurement systems
1. Mobile "Industrial" 3-D measurement systems
1.1 Total Station
1.2 Photogrammetry
Introduction Date: 02.09.2014Page: 2
1.3. Laser Tracker
1.2. Laser Scanner
1.4 Laser Radar
Company information
Foundation:
2001
Employee (in Europe):
3 Management
30 Technicians & Engineers
2 Administration
Departments:
� M3DMT – Mobile 3D on-site Measurements
� ScauD - Scanning and Digitizing
� PuK – Calibration Service for Machine Tools and CMM
sigma3D Datum: 29.06.2012Seite: 3
® 2010 sigma3D GmbH • www.sigma3D.de • [email protected]
sigma3D – Mobile 3D on-site Measurements
M3DMT – Aerospace Industrie
Datum: 02.09.2014Seite: 4
® 2010 sigma3D GmbH • www.sigma3D.de • [email protected]
Build Yigs and Tools
Periodic inspection
100% Part inspection
New measurement concepts
sigma3D – Mobile 3D on-site Measurements
M3DMT – Particle Accelerator
Datum: 02.09.2014Seite: 5
® 2010 sigma3D GmbH • www.sigma3D.de • [email protected]
Setup Magnets
3D Network measurement
Adjust special components
Support new ideas/experiments
sigma3D – Scanning and Digitizing
ScauD – 3D Quality control
Datum: 02.09.2014Seite: 6
® 2010 sigma3D GmbH • www.sigma3D.de • [email protected]
Data comparison with point clouds
Initial sampling
Actual to CAD data
Prozess control / Variance analysis
sigma3D – Scanning and Digitizing
ScauD – Reverse Engineering
Datum: 02.09.2014Seite: 7
® 2010 sigma3D GmbH • www.sigma3D.de • [email protected]
Draw up 3D CAD data
Build free-form surfaces
Parametric CAD construction
CAE -Computer Aided Engineering
Using different mobile 3D measurement technologies.
Mobile 3D Measurement Systems
sigma3D Datum: 02.09.2014Seite: 8
® 2010 sigma3D GmbH • www.sigma3D.de • [email protected]
Total Station
CMM
Overview 3D Systems
Industrial 3D Measurement Systems
Datum: 02.09.2014Seite: 9
® 2010 sigma3D GmbH • www.sigma3D.de • [email protected]
0,001
0,010
0,100
1,000
10,0
0,01 0,1 1 10 100 1000
Max.
Perm
issi
ble
Err
or
MP
E [m
m]
Measurement Range [m]
Terr. Laser Scanner
Laser TrackerLaser Tracker
Laser TrackerPhotogrammetrie
Laser RadarStructure-Light
ArticulatingArm
Industrial-Tachymeter
Grey=“optical“ Probing
Theodolite / Tachymeter
Industrial-Tachymeter / Total Station
Datum: 02.09.2014Seite: 10
® 2010 sigma3D GmbH • www.sigma3D.de • [email protected]
Manufacturer:• Leica• Sokkia
Physical principleOptical angle measurement + Speed of light (distance)
AdvantageLong rangeDifferent Target types
Disadvantage Highest accuracy only with CCRTrigger Mode Single pointsRange 2 to 120mAccuracy (MPE) ±0,3mm + 13µm/mTypical Application Shipbuilding / RailwayTraceability ISO 17123-5, DIN 18723-6Price 45.000 to 80.000 €Target Retroreflector / Reflective tape
Total Station
Total Station – Application in Antenna Alignment
Datum: 02.09.2014Seite: 11
® 2010 sigma3D GmbH • www.sigma3D.de • [email protected]
Application:• Steel Structure (Alidade / BUS)• Setting Reference Points• Single Part positioning• (Refector Alignment)
Accuracy:• 0,5mm to 3mm
Targets:• Reflective tape• CCR (Corner Cube Reflector)
Total Station
Total Station – Application: Steel Structure Alignment (SRT, 2010)
Datum: 02.09.2014Seite: 12
Application:• BUS Alignment• Panel supports
Total Station
Total Station – Application: Setting Reference Points (SRT 2009)
Datum: 02.09.2014Seite: 13
® 2010 sigma3D GmbH • www.sigma3D.de • [email protected]
Total Station
Total Station – Application: Reflector (Pre-Alignment)
Datum: 02.09.2014Seite: 14
® 2010 sigma3D GmbH • www.sigma3D.de • [email protected]
Disadvantages:• Only in 90° Elevation• Changing conditions
(temperature)
Accuracy:• 0,5mm to 1mm
Targets:• Reflective tape• Retroreflector
Critical• Intersection angle• Structure movement
during measurement
Laser Scanner
Laser Scanner
Datum: 02.09.2014Seite: 15
® 2010 sigma3D GmbH • www.sigma3D.de • [email protected]
Manufacturer :• Faro• Leica Geosystems• Riegl
Physical principleOptical angle mearsurement+ Speed of light / Phase-shift
AdvantageFast data acquisition“Optical“ probing (no targets)Option: with targets
DisadvantageHugh data volumeDistance not accurate
Trigger Mode ScanningRange 0,6 to 120mAccuracy (MPE) ±2 to 5mm
Typical ApplicationAs-built documentationBuilding reconstruction
Traceability ISO 17123-9Price 30.000 bis 80.000 €Target Non or paper targets
Laser Scanner
Laser Scanner – Application in Antenna Alignment
Datum: 02.09.2014Seite: 16
® 2010 sigma3D GmbH • www.sigma3D.de • [email protected]
Application:• As-built documerntation• Completeness check• (Panel Surface RMS > 1000µm)
Accuracy:• 2mm to 5mm
Targets:• non• Paper targets• Sphere targets
Laser Scanner
Laser Scanner – Application: As-built documentation
Datum: 02.09.2014Seite: 17
® 2010 sigma3D GmbH • www.sigma3D.de • [email protected]
10 positions on the ground, 4 positions in the main reflector, one of them on the feed cone.
Laser Scanner
Laser Scanner – Application: As-built documentation
Datum: 02.09.2014Seite: 18
® 2010 sigma3D GmbH • www.sigma3D.de • [email protected]
The Measurement was done with a resolution of 3mm at 10m distance.
Laser Scanner
Laser Scanner – Application: As-built documentation
Datum: 02.09.2014Seite: 19
® 2010 sigma3D GmbH • www.sigma3D.de • [email protected]
The 14 individual scans have been connected and deployed to a single point cloud.
Laser Scanner
Laser Scanner – Application: As-built documentation
Datum: 02.09.2014Seite: 20
® 2010 sigma3D GmbH • www.sigma3D.de • [email protected]
3D point cloud is modeled to a CAD model in step- and dwg-format
Laser Scanner
Laser Scanner – Application: As-built documentation
Datum: 02.09.2014Seite: 21
® 2010 sigma3D GmbH • www.sigma3D.de • [email protected]
Center-axis model of steel structure for FEM Analysis
Laser Scanner
Laser Scanner – Application: As-built documentation
Datum: 02.09.2014Seite: 22
® 2010 sigma3D GmbH • www.sigma3D.de • [email protected]
Quality check: CAD model to measured points
Laser Tracker
Laser Tracker
Datum: 02.09.2014Seite: 23
® 2010 sigma3D GmbH • www.sigma3D.de • [email protected]
Manufacturer:• Faro• Hexagon• API
Physical principleOptical angle measurement + Interferometry / Phase-shift & SoL
Advantage Accurate distance measurement“Online“ measurements possible
Disadvantage Target (Retroreflector) needed
Trigger Mode Single-points, ScanningRange 0 to 80mAccuracy (MPE) 20µm to 400µm
Typical Application3D / 6D Online-Adjustment, Tool & Yig verification
TraceabilityISO 10360-10, VDI 2617-10, ASME B89.4.19
Price 60.000 to 250.000 €Target Retroreflector (CCR, SMR, BMR)
Laser Tracker
Comparison: Laser Tracker from FARO vs. Leica
Datum: 02.09.2014Seite: 24
® 2010 sigma3D GmbH • www.sigma3D.de • [email protected]
Faro Leica
ION Vantage AT401 AT901
ADM-Accuracy (MPE) 16µm+0,8µm/m 16µm+0,8µm/m ±10µm ±10µm
IFM-Accuracy (MPE) 4µm+0,8µm/m - - ±0.4µm+0,3µm/m
R0 Parameter (MPE) 16µm 16µm - 5µm
Encoder Accuracy (MPE) 20µm+5µm/m 20µm+5µm/m 15µm+6µm/m ±15µm+6µm/m
XYZ-Coordinate (typical v.) 15µm+6µm/m 15µm+6µm/m 15µm+6µm/m ±7,5µm+3µm/m
Level (MPE) ±2“ ±2“ ±1“ (2σ) ±1“+0,5%
Range (distance) 55m 80m 320m 160m
Range (horizontal) ±270° ±360° ±360° ±360°
Range (vertikal) 75° bis -50° 77,9° bis -52,1° ±145° ±45°
Sample Rate 10.000/sec 10.000/sec 2/sec 3000/sec
QuellenION: FARO ION - Features, Benefits & Technical Specifications (01.2013)Vantage: FARO Laser Tracker Vantage - Features, Benefits & Technical Specifications (07.2012)AT401: Leica Absolut Tracker AT401 – Absolut portable (April 2010)AT901: PCMM System Specifications - Leica Absolute Tracker and Leica T-Products (02.2008)
Laser Tracker
Laser Tracker – Application in Antenna Alignment
Datum: 02.09.2014Seite: 25
® 2010 sigma3D GmbH • www.sigma3D.de • [email protected]
Application:• Setting Reference Points• 6 DOF single-part positioning• Movement Sub-Refector
Accuracy:• 0,05mm to 0,15mm
Targets:• Retrorefl. (> 750 US$/each)• CCR (Corner Cube Reflector)• SMR (Spherical Mounted R.)• BMR (Ball Mounted R.)
Laser Tracker
Laser Tracker – Application: Set Reference points
Datum: 02.09.2014Seite: 26
Set reference points for Photogrammetry setup
2521
Laser Tracker
Laser Tracker – Application: 6 DOF positioning mirrors
Datum: 02.09.2014Seite: 28
Application:• Solid-mirror Alignment• Online-Adjustment
Laser Tracker
Laser Tracker – Application: Movement Sub-Reflector
Datum: 02.09.2014Seite: 29
Application:• Check the movement of the
Sub-Refector transit systemfrom inside the SR-cabin
Laser Tracker
Laser Tracker – Application: Sub-Reflector different elevation angle
Datum: 02.09.2014Seite: 30
Laser Tracker
Laser Tracker – Application: Sub-Reflector different elevation angle
Datum: 02.09.2014Seite: 31
Application:• Movement of the Sub-Refector
in different elevation angle (calibration hexapod)
Laser Tracker
Laser Tracker – Application: Sub-Reflector different elevation angle
Datum: 02.09.2014Seite: 32
Laser Tracker
Laser Tracker – Application: Sub-Reflector different elevation angle
Datum: 02.09.2014Seite: 33
Project M2-Alignment
Measurement place SRT, San Basilio, Sardinia
Date 15.08.2011, 21:10 - 21:25 Uhr
Measurement object SRT - M2 (Subreflector)
Customer MT Mechatronics
Contact person on site Mr. S. Doth sigma3D GmbH
Measurement system Laser Tracker Faro SN 3301 Max-Hufschmidt-Str.4a
Inspector H. Paluszek, sigma3D GmbH D-55130 Mainz
Air temperature 21°C - 20°C Tel. +49 (0) 61 31 - 96 257 - 0
Material temperature 17°C - 18°C (Material-kompensation on 20° C) Fax +49 (0) 61 31 - 96 257 - 20
Coordinate System M1 Mirror after Best-Fit calculation www.sigma3D.de
(karthesian) Best-Fit with 6 Parameter [email protected]
Remark Measurement in 90° Position (1st)
Point ID Measured (act.) M1 Best-Fit (nominal) deviation (actual - nominal) Remark
RHR x [mm] y [mm] z [mm] x [mm] y [mm] z [mm] ∆x [mm] ∆y [mm] ∆z [mm]
Mirror Reference points in M1 coordinate system
2521 3660.96 22.26 4521.45 3661.02 22.22 4521.30 -0.06 0.04 0.152522 -37.03 -3692.51 4517.86 -36.94 -3692.64 4517.99 -0.09 0.13 -0.132523 -3439.50 -1431.09 4523.18 not visible from LT Stand2524 -3419.27 1414.60 4513.91 -3419.18 1414.72 4513.73 -0.09 -0.12 0.182525 -1451.13 3408.54 4511.66 -1451.23 3408.72 4511.78 0.10 -0.18 -0.122526 1447.95 3402.79 4504.34 1447.82 3402.65 4504.43 0.13 0.14 -0.09
M2_Ref1 -1.63 39.98 23739.96 0.21 -0.51 23742.94 -1.84 40.49 -2.98 Mid-pointM2_Ref2 77.51 -412.41 23738.70 80.07 -452.69 23743.10 -2.56 40.28 -4.40M2_Ref3 351.10 336.51 23740.79 352.49 296.57 23743.06 -1.39 39.94 -2.27M2_Ref4 -433.69 199.27 23740.80 -431.99 158.14 23743.03 -1.70 41.13 -2.23
21300 13158.87 15329.01 6690.88 13155.12 15323.13 6697.80 3.75 5.88 -6.9223700 -15379.33 13143.68 6585.24 -15373.88 13139.43 6589.49 -5.45 4.25 -4.2526100 -13174.43 -15333.90 6705.44 not measured28500 15433.71 -13104.74 6543.72 15436.33 -13109.61 6541.50 -2.62 4.87 2.22
Laser Tracker
Laser Tracker – Application: Sub-Reflector different elevation angle
Datum: 02.09.2014Seite: 34
Tra x 1.931 mm
Tra y -40.446 mm
Tra z 3.095 mm
Rotx 0.1752 DEG = 631 arcsec
Roty 0.0333 DEG = 120 arcsec
Rotz -0.0873 DEG = -314 arcsec
Scale x 1
Scale y 1
Scale z 1
xy 0
Azimuth 0
ZtoXY 0
R_Dist 0
s0 0.033
sx 0.049 max x 0.037 min x -0.07 max x - min x 0.107
sy 0.041 max y 0.03 min y -0.06 max y - min y 0.09
sz 0.007 max z 0.004 min z -0.011 max z - min z 0.014
PktNr. MCS.x MCS.y MCS.z OCS.x OCS.y OCS.z dev.x dev.y dev.z
M2_Ref1 0.242 -0.478 -0.068 0.205 -0.508 -0.057 0.037 0.03 -0.011
M2_Ref2 80.071 -452.749 0.102 80.067 -452.689 0.098 0.004 -0.06 0.004
M2_Ref3 352.52 296.59 0.061 352.49 296.572 0.057 0.03 0.018 0.004
M2_Ref4 -432.06 158.155 0.034 -431.99 158.142 0.03 -0.07 0.013 0.004
Laser Tracker
Laser Tracker – Application: Sub-Reflector different elevation angle
Datum: 02.09.2014Seite: 35
Project M2-Alignment
Measurement place SRT, San Basilio, Sardinia
Date 15.08.2011, 23:52 - 23:59 Uhr
Measurement object SRT - M2 (Subreflector)
Customer MT Mechatronics
Contact person on site Mr. S. Doth sigma3D GmbH
Measurement system Laser Tracker Faro SN 3301 Max-Hufschmidt-Str.4a
Inspector H. Paluszek, sigma3D GmbH D-55130 Mainz
Air temperature 21°C - 20°C Tel. +49 (0) 61 31 - 96 257 - 0
Material temperature 17°C - 18°C (Material-kompensation on 20° C) Fax +49 (0) 61 31 - 96 257 - 20
Coordinate System M1 Mirror after Best-Fit calculation www.sigma3D.de
(karthesian) Best-Fit with 6 Parameter [email protected]
Remark Measurement in 5° Position
Point ID Measured (act.) M1 Best-Fit (nominal) deviation (actual - nominal) Remark
RHR x [mm] y [mm] z [mm] x [mm] y [mm] z [mm] ∆x [mm] ∆y [mm] ∆z [mm]
Mirror Reference points in M1 coordinate system
2521 3661.02 22.26 4521.53 3661.02 22.22 4521.30 0.00 0.04 0.232522 -37.05 -3692.55 4517.81 -36.94 -3692.64 4517.99 -0.11 0.09 -0.182523 -3439.50 -1431.09 4523.18 not visible from LT Stand2524 -3419.29 1414.60 4513.98 -3419.18 1414.72 4513.73 -0.11 -0.12 0.252525 -1451.12 3408.55 4511.63 -1451.23 3408.72 4511.78 0.11 -0.17 -0.152526 1447.93 3402.81 4504.28 1447.82 3402.65 4504.43 0.11 0.16 -0.15
M2_Ref1 -1.29 -17.11 23748.79 0.21 -0.51 23742.94 -1.50 -16.60 5.85 Mid-pointM2_Ref2 78.02 -469.48 23749.20 80.07 -452.69 23743.10 -2.05 -16.79 6.10M2_Ref3 351.35 279.59 23748.53 352.49 296.57 23743.06 -1.14 -16.98 5.47M2_Ref4 -433.37 142.07 23749.09 -431.99 158.14 23743.03 -1.38 -16.07 6.06
21300 13152.44 15321.90 6701.69 13155.12 15323.13 6697.80 -2.68 -1.23 3.8923700 -15370.47 13136.12 6592.10 -15373.88 13139.43 6589.49 3.41 -3.31 2.6126100 -13174.43 -15333.90 6705.44 not measured28500 15437.13 -13111.07 6542.32 15436.33 -13109.61 6541.50 0.80 -1.46 0.82
Laser Tracker
Laser Tracker – Application: Sub-Reflector different elevation angle
Datum: 02.09.2014Seite: 36
Tra x 1.5 mm
Tra y 16.617 mm
Tra z -5.86 mm
Rotx -0.0347 DEG = -125 arcsec
Roty 0.0368 DEG = 132 arcsec
Rotz -0.0678 DEG = -244 arcsec
Scale x 1
Scale y 1
Scale z 1
xy 0
Azimuth 0
ZtoXY 0
R_Dist 0
s0 0.037
sx 0.036 max x 0.025 min x -0.052 max x - min x 0.077
sy 0.059 max y 0.047 min y -0.085 max y - min y 0.132
sz 0.016 max z 0.008 min z -0.024 max z - min z 0.032
PktNr. MCS.x MCS.y MCS.z OCS.x OCS.y OCS.z dev.x dev.y dev.z
M2_Ref1 0.227 -0.498 -0.081 0.205 -0.508 -0.057 0.022 0.01 -0.024
M2_Ref2 80.071 -452.774 0.106 80.067 -452.689 0.098 0.004 -0.085 0.008
M2_Ref3 352.515 296.619 0.065 352.49 296.572 0.057 0.025 0.047 0.008
M2_Ref4 -432.042 158.171 0.038 -431.99 158.142 0.03 -0.052 0.029 0.008
Laser Radar
Laser Radar
Datum: 18.06.2013Seite: 37
® 2010 sigma3D GmbH • www.sigma3D.de • [email protected]
Manufacturer:• Nikon (MetricVision)
Physical principleOptical angle measurement + Radar
AdvantageHigh accuracy(like Laser Tracker)Without Target
Disadvantage No industrial standard / PriceTrigger Mode Single-points, ScanningRange 1 to 50mAccuracy (MPE) 24 to 300µm
Typical Application Large Surface Scanning
Traceability ? (non)Price 180.000 to 280.000 €Target Non or Retroreflector
Laser Radar
Laser Radar – Application in Antenna Alignment
Datum: 02.09.2014Seite: 38
® 2010 sigma3D GmbH • www.sigma3D.de • [email protected]
Application:• Panel Inspection• Panel Alignment• Deformation Verifiation• Movement Sub-Refector
Accuracy:• 0,05mm to 0,15mm
Targets:• Scanning without Targets
possibel!
Photogrammetry
Digital Photogrammetry
Datum: 02.09.2014Seite: 39
® 2010 sigma3D GmbH • www.sigma3D.de • [email protected]
Manufacturer:• Aicon3D• GOM• GSI
Physical principle Multiangulation + Scale
AdvantageFlexible (Range / Accuracy)
DisadvantageTarget (tape or paper) neededOffline method
Trigger mode Single-pointsRange 0 to 100mAccuracy (MPE) 2µm + 5µm/m (RMS)
Typical ApplicationDeformation analysisSurface measurements
Traceability VDI 2634-2Price 10.000 to 40.000 €
TargetsReflective TapePaper targets
Photogrammetry
Photogrammetry – Application in Antenna Alignment
Datum: 02.09.2014Seite: 40
® 2010 sigma3D GmbH • www.sigma3D.de • [email protected]
Application:• Panel / SR Alignment• Deformation Verification
Accuracy:• 0,03mm to 0,2mm
Targets:• Paper targets (up to d=15m)• Reflective tape
Measurement & Evaluation
Photogrammetry – Application: Panel / SR Alignment
Datum: 12.06.2012Seite: 41
Photogrammetry
Photogrammetry – Application: Panel / SR Alignment
Datum: 02.09.2014Seite: 42
® 2010 sigma3D GmbH • www.sigma3D.de • [email protected]
Photogrammetry
Photogrammetry – Application: Deformation Verification (SRT)
Datum: 02.09.2014Seite: 43
Deformation of the Main-Reflector in various Elevation (90/75/60/45/30/15).
Photogrammetry
Photogrammetry – Application: Deformation Verification (SRT)
Datum: 02.09.2014Seite: 44
Photogrammetry
Accuracy Photogrammetry
In general, the following approach applies to the measurement accuracy (Sxyz):
Sxyz = q * m * Sx‘y‘
For panel measurements following theoretical uncertainty estimated:
� Reflector diameter 13 m: Sxyz = 0,7 * 700 * 0,07 µm -> 34 µm -> RMS 70 µm (VLBI 2014)
� Reflector diameter 15 m: Sxyz = 0,8 * 800 * 0,07 µm -> 45 µm -> RMS 90 µm
� Reflector diameter 40 m: Sxyz = 0,8 * 1400 * 0,07 µm -> 78 µm -> RMS 180 µm
� Reflector diameter 64 m: Sxyz = 0,8 * 1900 * 0,07 µm -> 106 µm -> RMS 290 µm (SRT 2012)
� Reflector diameter 100 m: Sxyz = 0,8 * 2200 * 0,08 µm -> 140 µm -> RMS 350 µm
Reachable: Only with stable measurement conditions, good panels and the right strategy!
Datum: 02.09.2014Seite: 45
q = Quality factor for the geometry of the recordings0.4 to 0.8 with a good configuration, 2 for bad configuration
m = Image scale
Sx‘y‘ = Image measurement accuracy
Accuracy with mobile 3D “industrial“ Measurement systems
Conclusion: Antenna Alignment with mobile 3D Systems
Datum: 02.09.2014Seite: 46
® 2010 sigma3D GmbH • www.sigma3D.de • [email protected]
Antenna Part Alignment task Accuracy 3D Systems
Steel construction Aligment of steel construction 1 - 5 mm Total Station / (Laser Tracker)
Single-ComponentTests
Roundness, centering, ... of single-parts
0,04 – 0,2 mm Laser Tracker
Secundary Mirrors 6 DOF-Alignment 0,05 - 0,15 mm Laser Tracker / (Total Station)
M1 Surface Panel Alignment 0,03 - 0,1 mm Photogrammetry / Laser Radar
M1 Surface Deformation measurement in various elevation angles
0,05 - 0,15 mm Photogrammetry / (Laser Radar)
Sub-Reflector Displacement verification in various elevation angles
0,1 - 0,2 mm Photogrammetry / Laser TrackerLaser Radar / (Total Station)
Complete Antenna As-built documentation 2 - 5 mm Terrestical Laser Scanner (TLS)
End Datum: 02.09.2014Seite: 47
® 2010 sigma3D GmbH • www.sigma3D.de • [email protected]
www.sigma3D.de
Visit also:• VDI FA Large Volume Metrology - Symposium, 18th Sept. 2014, Magdeburg• IWAA – International Workshop for Accelerator Alignm., Oct. 2014, Beijing• LVMC - Large Volume Metrology Conference, Nov. 2014, Manchester• CMSC – Coordinate Measurement System Conference, July 2015, USA
Thank you for your attention!