2005odyssey3rdrowsunshade
TRANSCRIPT
© 2004 American Honda Motor Co., Inc - All Rights Reserved. AII 27366 (0409) 1 of 6
INSTALLATIONINSTRUCTIONS
Accessory Application Publications No.
Issue Date
SEP 2004
2005 ODYSSEY3RD ROW
SUNSHADEP/N 08R12-SHJ-100
PARTS LIST Driver’s Side
1. Remove the left speaker cover (two clips andthree retaining tabs).
Right side rear sunshade
4 Brackets
4 Rivets
TOOLS AND SUPPLIES REQUIRED
Felt-tip pen
Center punch
Drill
7 mm Drill bit
Isopropyl alcohol
6 inch Scale
Hammer
08R12-SHJ-1000-91
AII 27366
Left side rear sunshade
4326060Y
LEFT REAR SIDETRIM PANEL
CLIPS (2)
RETAININGTABS (3)
LEFT SPEAKERCOVER
2 of 6 AII 27366 (0409) © 2004 American Honda Motor Co., Inc - All Rights Reserved.
2. Gently pull out on the side trim panel to releasethe panel clips around the glass. Fit the twobrackets from the left rear sunshade over the edgeof the left rear side trim panel. Align the rear edgeof the sunshade just past the edge of the seat beltcover.
3. Using a felt-tip pen, mark the left rear side trimthrough the center of each bracket hole. Removethe rear sunshade.
4. Center punch the marks you made in the left rearside trim panel and drill each mark with a 7 mm drillbit:
• Using adhesive tape, wrap the end of the drill bit5 mm from the tip.
• While wearing eye protection, drill a 7 mm holethrough each center-punched mark.
• Remove any burrs from the drilled holes.
5. Reinstall the left rear sunshade on the left rearside trim panel, and align the brackets from theleft rear sunshade with the holes you drilled.
4326080Y
FELT-TIP PEN
MARK
LEFT REARSIDESUNSHADE
LEFT REARSIDE TRIMPANEL
4326100Y
Holes drilledin step 4.
LEFT REAR SIDETRIM PANEL LEFT
REARSUNSHADE
RIVETS
LEFT REARSUNSHADEBRACKET
LEFT REARSUNSHADE
LEFT REARSIDE TRIMPANEL
FRONT
Align SEAT BELTCOVER
LEFT REARSIDE TRIMPANEL
LEFT REARSUNSHADE
LEFT REARSUNSHADEBRACKET
LEFTREARSUNSHADE
MARK
LEFT REARSIDE TRIMPANEL
7 mm DRILLBITCENTER
PUNCH
7 mm DRILL BIT
5 mm
ADHESIVETAPE
32 mm
6. Secure the two brackets from the left rearsunshade to the left rear side trim panel with thetwo rivets. Reinstall the left rear side trim panel.
© 2004 American Honda Motor Co., Inc - All Rights Reserved. AII 27366 (0409) 3 of 6
7. Insert a 6 inch scale against the top of the rearwindow between the glass and the headliner untilthe scale contacts the top of the glass. Measure25 mm down from the top of the glass, and attachstrips of masking tape to the window in the areasshown.
8. Pull up the left rear sunshade. Align the twocutouts in the left rear sunshade with the twostrips of masking tape attached to the rearwindow. Using a felt-tip pen, mark the top of themasking tape at each side of cutout in the rearsunshade. Roll down the left rear sunshade.
10. Remove the adhesive backing from one of thebrackets and attach the bracket to the top of theright rear window between the marks on themasking tape. Install the other bracket the sameway. Remove the masking tape from the window.
11. Pull up the sunshade and hook the sunshade tothe brackets.
12. Snap the rear trim panel back into place.
9. Using isopropyl alcohol on a shop towel, clean theleft rear window above the marks you made on themasking tape.
4427050Y
CUTOUT INLEFT REARSUNSHADE
FELT-TIP PEN
MASKINGTAPE
MARK LEFT REARSUNSHADE
LEFT REAR SIDETRIM PANEL
4326111Y
BRACKET
MARK
STOP AT TOP OFLEFT REAR WINDOW
Align with the bracket.
ATTACHMENTPOSITION
MASKINGTAPE
MASKINGTAPE
LEFT REAR SUNSHADE
LEFTREARWINDOW
MASKING TAPE
ADHESIVEBACKING
4427040Y
200 mm
200 mm
25 mm
LEFT REARSIDE TRIMPANEL
LEFT REARWINDOW
MASKINGTAPE
MASKINGTAPE6 INCH
SCALE
LEFTREARWINDOW
STOP AT TOP OFLEFT REAR WINDOW
4 of 6 AII 27366 (0409) © 2004 American Honda Motor Co., Inc - All Rights Reserved.
16. Check that the marks are 32 mm away from theedge of the right side trim panel. Center punch themarks you made in the right rear side trim panel anddrill each mark with a 7 mm drill bit:
• Using adhesive tape, wrap the end of the drill bit5 mm from the tip.
• While wearing eye protection, drill a 7 mm holethrough each center-punched mark.
• Remove any burrs from the drilled holes.
13. Remove the right rear speaker cover (two clips,and three retaining tabs).
14. Gently pull out on the side trim panel to releasethe panel clips from the edge of the right side trimpanel. Fit the two brackets from the right rearsunshade over the edge of the rear side trimpanel. Align the rear edge of the sunshade 20 mmfrom the rear edge of the seat belt cover.
15. Using a felt-tip pen, mark the right rear side trimthrough the center of each bracket hole. Removethe rear sunshade.
4329091Y
20 mmSEAT BELTCOVER
RIGHT REARSIDE TRIM PANEL
RIGHT REARSUNSHADE
RIGHT REARSUNSHADE BRACKET
FRONT
RIGHT REARSUNSHADE
RIGHT REARSUNSHADEBRACKET
RIGHT REARSIDE TRIMPANEL
RIGHT REARSUNSHADE
4329110YMARK
RIGHT REARSIDE TRIMPANEL
FELT-TIP PEN
RIGHT REARSUNSHADE
4329080Y
RIGHT REAR SIDETRIM PANEL
CLIPS (2)
RETAININGTABS (3)RIGHT SPEAKER
COVER
CENTERPUNCH
MARKRIGHT REARSIDE TRIM PANEL
7 mmDRILLBIT
ADHESIVETAPE
5 mm
7 mmDRILL BIT
32 mm
© 2004 American Honda Motor Co., Inc - All Rights Reserved. AII 27366 (0409) 5 of 6
18. Secure the rear sunshade to the rear trim panelusing two rivets from the kit, then snap the reartrim panel back into place.
19. Insert a 6 inch scale against the top of the rearwindow between the glass and the headliner untilthe scale contacts the top of the glass. Measure25 mm down from the top of the glass, and attachstrip of masking tape to the window in the areasshown.
17. Reattach the rear sunshade on the side trim panel,and align the brackets over the drilled holes in thetrim panel.
20. Pull up the rear sunshade until the cutouts in thesunshade reach the masking tape. Using a felt-tippen, mark the top of the masking tape at eachside of each cutout. Roll down the rear sunshade.
21. Using isopropyl alcohol on a shop towel, clean theright rear window above the marks you made onthe masking tape.
4428010Y
200 mm200 mm
RIGHT REARSIDE TRIMPANEL
MASKING TAPE
25 mm
RIGHT REARWINDOW
RIGHT REARWINDOW
6 INCH SCALE STOP AT TOPOF RIGHT REARWINDOW
MASKINGTAPE
4428030Y
Align with thebracket.
STOP AT TOPOF RIGHTREAR WINDOW
BRACKET
ATTACHMENTPOSITION
MASKINGTAPE
MARK
MASKINGTAPE
RIGHT REARWINDOW
MASKINGTAPE
ADHESIVEBACKING
BRACKET
RIGHT REARSUNSHADE
4329120Y
RIVETS
Holes drilledin step 16
RIGHT REARSIDE TRIM PANEL
RIGHT REARSUNSHADE
4428020Y
MASKINGTAPE
FELT-TIPPEN
MARK
CUTOUT INRIGHT REARSUNSHADE
RIGHT REARSUNSHADE
RIGHT REARSIDE TRIMPANEL
6 of 6 AII 27366 (0409) © 2004 American Honda Motor Co., Inc - All Rights Reserved.
22. Remove the adhesive backing from one of thebrackets and attach the bracket to the top of theright rear window between the marks on themasking tape. Install the other bracket the sameway. Remove the masking tape from the window.
23. Pull up the sunshade and hook the sunshade tothe brackets.