20 ways to improve productivity in garment production.docx

8/10/2019 20 Ways to Improve Productivity in Garment Production.docx

1/7

20 Ways to Improve Productivity in Garment

Production

Higher productivity brings higher margin in a business. And increment in Productivity level

reduces garment manufacturing cost. Hence factory can make more profit through productivity

improvement.

In this article top 20 ways have been discussed

that will certainly help factories to boost up current labor productivity. All the means that had

been explained here can be implemented as because most of these are at your reach. Machine

productivity as well as labor productivity increases when a factory produces more pieces by the

existing resources (Manpower, time and machinery).

When I look into the processes and operations during my visit to factories, I find improvement

potential is there in every area. Initially, you may not be able to find and measure potential

areas. Still you can improve productivity by applying some of the following steps.

I have mentioned 20 ways where you can focus and start working on improving productivity. To

provide you knowledge in details few links have been given for your further reading in some of

the steps. Most of the tips mentioned in this article are mainly on time saving tips, discipline

and proper planning. To get excellent result you may need external recommendation and

support but without the external help you can surely get measurable improvement once you

start your journey.
http://4.bp.blogspot.com/-oAlmV1-GHjI/T2jYVItx0AI/AAAAAAAAAjE/9LVqMFwdIlc/s1600/productivty+improvement+graph.jpghttp://www.onlineclothingstudy.com/2012/02/20-ways-to-improve-productivity-in.html


2/7

One thing you need to understand that application of the following steps will vary based on

production systems. I have written this article focusing on progressive bundle system.

If you are new in the productivity discussion, before stepping into following steps, I will suggestyou readHow to measure labor productivitythat will help you to understand following

discussions.

1. Conducting motion study and correcting faulty motions: There is a saying Even best can be

improved. So go to Gemba (sewing floor) and look for operators working method and

movements. Prepare a check list for good methods and movements. At time of motion study

observe operators movement and compare with you checklist. If you found wrong movements

is used by operator or unnecessarily extra movement is present in the operation cycle correct

it. If needed deskill operator. By doing this you can reduce operation cycle time and canimprove labor productivity up to 100%* in individual operations (*in 20% of the total

operations as per Paretos 80-20 Principle).

2. Hourly operator capacity check:Employ work study personnel (if you dont have) and start

checking operator capacity hourly or bi-hourly. Compare actual operators hourly production

with their capacity. If production is less then question them why? It helps in two waysfirst,

when operators capacity is checked at regular interval they will be under pressure. Secondly,

work study personnel start thinking on methods how cycle time can be reduced. Using the

capacity data, you can move ahead in balancing the line.

3. Conduct R&D for the garment:A non-value added (NVA) process but having a strong

Research and Development (R&D) team in the factory brings lot of benefits. R&D can be taken

as preparation stage for the bulk production. This department does sample production and look

into potentially critical operations, plan for requirement of special equipment, advice changes

in terms of construction without changing styling. E.g. if an operation contains some raw

stitches, which doesnt affect the final look of the garment, then that operation can be avoided

if possible to save time. They plan for skill requirement for the operations. As a result

production runs without any break or with less no. of breaks. As it reduces the chance of break

in production for unnecessary reasons, line productivity doesnt come down.

4. Use best possible line layout:Line layout means placing of machines and centre table (trolley

with wheel) as per style requirement. The main purpose of choosing a better layout is to reduce

transportation time in the line as much as possible. A stable line is not a good idea if you

produce multiple products in a same line. A straight assembly line with centre table at left side
http://www.onlineclothingstudy.com/2011/02/measuring-labor-productivity.htmlhttp://www.onlineclothingstudy.com/2011/02/measuring-labor-productivity.htmlhttp://www.onlineclothingstudy.com/2011/02/measuring-labor-productivity.htmlhttp://www.onlineclothingstudy.com/2011/02/measuring-labor-productivity.html


3/7

is good for a product that has no preparatory work and individual operation SAM is nearby the

pitch time. When a style includes lot of preparatory work (for garment parts), it is better to

make garment parts in sections and assemble them later. If possible use overhead

transportation system.

5. Scientific work station layout: The workstation layout defines from where an operator will

pick up work (garment components) and where she will dispose stitched garment. A scientific

layout is defined as minimum reach for picking up and dispose of components. Every

components and tools (trimmer) must be kept within operator reach. During workstation

designing, engineering must follow key principles.

Components to be worked on should be positioned as near to the needle as possible.

Direction of the components where it positioned on the table or track should be such

way that during moving component to the needle point does not need to turn it.

Placing of work at the same plane of the machine table so that operator can easily slide

it to needle point.

The purpose of designing a good workstation layout is to minimize the material handling time

as much as possible. Thus you can reduce operation cycle time. Secondary benefit of good

workstation is operators can work at same pace without fatigue. When designing a workstation

layout dont forget to consider ergonomics.

6. Reduce line setting time:It have been observed that a line reaches at its pick productivity

level on day 6-7 after loading of an order. The time lost in the initial days (learning curve) brings

down the average labor productivity for whole style. Reason - lot of time is lost during setting of

the line for a new style. This reduces overall machine productivity and line efficiency. So to

maintain line productivity level you have to work on minimising line setting time or throughput

time. To reduce the line setting time, engineers have to study the garment thoroughly, prepare

operation bulletin with machine requirement and machine layout plan prior to feeding cuttings

to the line. Read another article to knowhow to reduce line setting time. Engineers need to

coordinate with line supervisors and maintenance department with their plans and

requirements. This will help supervisors and maintenance department to be pro-active in

arranging required resources.

7. Improve line balancing:Purpose of balancing a line is to reduce operators idle time or

maximize operator utilization. In a balanced line work will flow smoothly and no time will be

lost in waiting for work. At time of line setting select operators for the operation matching

operator skill history and skill required. Following this method you will select highly skilled

operators for higher work content operations. Once line is set conduct capacity study at a

regular interval. Usepitch diagram method to find bottlenecks inside the line. You have to think
http://www.onlineclothingstudy.com/2011/10/how-to-reduce-line-setting-time-for.htmlhttp://www.onlineclothingstudy.com/2011/11/what-is-pitch-time-pitch-diagram-and.htmlhttp://www.onlineclothingstudy.com/2011/11/what-is-pitch-time-pitch-diagram-and.htmlhttp://www.onlineclothingstudy.com/2011/10/how-to-reduce-line-setting-time-for.html


4/7

how you willminimize WIP level at bottleneck operations. Read another article online

balancing for guidelines. Once you start increasing operator utilization through line balancing

you will get extra pieces from the same resources in defined time.

Even a well managed factory can improve productivity by 22% thorough line balancing reportedby Md. Rezaul Hasan Shumon, Kazi Ar if-Uz-Zaman, and Azizur Rahman in aResearch

Study Productivity Improvement through Line Balancing in Apparel Industries.

8. Use work aids, attachments, guides, correct pressure foots and folders:These are some

kinds of time saving devises that facilitate operator to perform their work effectively with less

effort. If work aids are used effectively operation cycle time can be reduced many fold than

existing cycle time. In new and small factories where there is no experienced technical person

(maintenance, IE personnel or production manager) generally not aware about the usage and

availability of work aids. So their operators sew garment free hand. Labor productivity iscomparably higher for the factories that widely use work aids than those who do not use work

aids for the similar products. Folders and attachments are also very helpful in producing

consistent stitching quality. On the other hand work aids, guides and fixtures reduce operators

movement and weight lifting. During my research study I college I had improved labor

productivity up to 18.03% using work aids in various operations.

9. Continuous feeding to the sewing line:It is not a fault of production department if they did

not get cuttings to sew. All plans and efforts towards productivity will fail if line is not been fed

continuously. No feeding or irregular feeding is one of the top reasons for lower productivity

in poorly managed factory. Poor production plan, wrong selection product mix in seasons and

ineffective cutting department are the reasons that stop continuous feeding. Once operators

get the rhythm, they should be given non-stop feeding until style changeover to keep up the

productivity. If you know there is unavailability of cutting in near future then plan accordingly

and dont call all operators for that duration.

10. Feed fault free and precise cutting to line:Stop cutting and trimming of extra fabric from

cut components by operators. If your cutter does not able to provide precise cutting s/he

should be trained. But faulty cutting dont be fed. When operatorscut fabric he performs

additional task in the operation cycle time. If in some cases trimming is intended then that task

must be included in total work content. Otherwise you will get wrong (less) efficiency for the

operator. Secondly, cuttings withfabric defects,pattern problem are issued to sewing line. As a

result line produces defective garments. Alteration and repair work for defective garments

reduces labor productivity.
http://www.onlineclothingstudy.com/2012/01/7-ways-to-reduce-wip-from-bottleneck.htmlhttp://www.onlineclothingstudy.com/2011/02/how-to-balance-traditional-sewing-line.htmlhttp://www.onlineclothingstudy.com/2011/02/how-to-balance-traditional-sewing-line.htmlhttp://www.iieom.org/paper/133%20rezaul.pdfhttp://www.iieom.org/paper/133%20rezaul.pdfhttp://www.onlineclothingstudy.com/2011/10/common-fabric-faults-found-in-garments.htmlhttp://www.onlineclothingstudy.com/2011/10/common-fabric-faults-found-in-garments.htmlhttp://www.iieom.org/paper/133%20rezaul.pdfhttp://www.iieom.org/paper/133%20rezaul.pdfhttp://www.onlineclothingstudy.com/2011/02/how-to-balance-traditional-sewing-line.htmlhttp://www.onlineclothingstudy.com/2011/02/how-to-balance-traditional-sewing-line.htmlhttp://www.onlineclothingstudy.com/2012/01/7-ways-to-reduce-wip-from-bottleneck.html


5/7

11. Training for Line supervisors:Line supervisors are shop floor managers. So each supervisor

must be trained with fundamental management skills and communication skill. Still in most of

the supervisors in Indian factories are raised from tailors. They dont acquire technical

qualification in supervising. But their main job is providing instruction, transferring information.

For which communication skill training is required for supervisors. Secondly, supervisor shouldunderstand the fundamental of industrial engineering like operation bulletin, skill matrix,

workstation layout, movement, capacity study and theoretical line balancing etc. If they

understood these, they can help engineers or work study boys to improve line performance.

The above training will bring changes in managing and controlling the lines and will improve

labor productivity.

12. Training to sewing operators:Operators are main resources in the apparel manufacturing.

They are most valuable resource to the company. So, factory must work on developing

operator skill where required. Training is not cost but an investment said by many experts.Production from an operator depends on his skill level to the task. A low skilled operator will

consume higher resources (time) and give less output. You will find quality related issues with

low skilled and untrained operators. As the skill level of the operators is increased through

training lines output will improve. Training does mean lot of time and money. Training should

be given only on specific tasks that will be performed by the operator. Pauls article systematic

training for apparel industry operatorsan introduction is very helpful in this regard.

13. Setting individual operator target: Instead of giving equal target to all operators working in

a line, give individual target as per operators skill level and capacity. Set an achievable target for

each operator so that they would try to reach the target. This will help improving operators

individual efficiency. Use tricks for increasing target step by step. Take care of the operators

who are under target. They may need skill training. Go back to point#12. Training for sewing

operators.

14. Eliminate loss time andoff-standard time:Utilize operators time as much as you can.

There is no better alternative than just stopping operators sitting idle to improve operator

productivity. Non productive time such as waiting for work, machine breakdown, power failure

and repair work kill your productivity. Start eliminating non-productive time as much as

possible. To start work on this point you have to track off-standard or non-productive time data

according to different categories. Once you have the analysis and Pareto of non-productive

time you can think and plan on reducing it.

15. Real time shop floor data tracking system:For the continuous improvement and prompt

action on failure you need information from the shop floor as fast as possible. Important
http://www.onlineclothingstudy.com/2012/01/systematic-training-of-sewing-industry.htmlhttp://www.onlineclothingstudy.com/2012/01/systematic-training-of-sewing-industry.htmlhttp://www.onlineclothingstudy.com/2012/01/systematic-training-of-sewing-industry.htmlhttp://www.onlineclothingstudy.com/2012/01/systematic-training-of-sewing-industry.htmlhttp://www.onlineclothingstudy.com/2011/10/what-is-on-standard-efficiency-and.htmlhttp://www.onlineclothingstudy.com/2011/10/what-is-on-standard-efficiency-and.htmlhttp://www.onlineclothingstudy.com/2012/01/systematic-training-of-sewing-industry.htmlhttp://www.onlineclothingstudy.com/2012/01/systematic-training-of-sewing-industry.html


6/7

information needed such as hourly production, line balancing, WIP, tracking bundles and

quality performance of the line. If corrective action is not been taken early problem may

increase as time goes. So RFID based real time systems are helping in providing shop floor

information within second. With Leadtec system Joshep Abboud increased its total productivity

more than 40% (refer to the following case study link). This system is quite costlier at this time.But as perpublished case studies ROI (12-18 months) of this RFID based real time system is not

bad.

16. Using auto trimmer sewing machine (UBT): Just think how many pieces an operator is

producing in a day? Each time an operator trims thread using a trimmer or scissors consume

time minimum 50 TMU or 2 Seconds (approx). A rough estimate, in a day operator will lose

about 20 minutes just in thread cutting. In an operation of 0.5 SAM, operator can make 40 extra

pieces. Even machine without auto trimmer consumes more sewing thread. Those who use

heavy (half kilogram weight) scissor may start using hand trimmer.

17. Installing better equipment:A low performing machine is not acceptable where some of

your good machines are idle in the same building. Use the best of your resources. If machines

or equipment dont perform well operator motivation goes down. Repetitive breakdown of

machines increase the loss time and bring down overall line efficiency and labor productivity. I

have seen lines where UBT machine is used in long seam operations and comparably lower

work content. On the other hand where shorter seams are being stitched, most of the time

spent in thread trimming for taking out work from the needle, normal lock stitch sewing

machine are used.

18. Inline quality inspection at regular interval:Traffic light system is the most effective

inspection tool to reduce defect generation at source. Less number of defective seam is made

less the time will be lost in repairing it. Inline checking system will alert operators in

concentrating their job. It also helps in other way. May be at the start of the style an operator

not understood the specification, an interaction with quality inspector will make an operator

clear about the quality requirement. Poorly managed factory loses productivity up to 10% due

to repair and reject as mentioned by Dr. Bheda in his articleProductivity in Apparel

Manufacturing.

19. Operator motivation:Operators will is the most crucial part in productivity improvement.

If they are motivated, they will put enough efforts on the work. Employee motivation generally

depends on various factors like work culture, HR policies, bonus on extra effort or achieving

target. In garment manufacturing operators motivation come through extra money. Operator
http://www.leadtec.com/images/stories/whitepapers/joseph%20abboud%20case%20study.pdfhttp://www.onlineclothingstudy.com/2012/01/traffic-light-system-for-quality.htmlhttp://www.consultwho.com/a4.asphttp://www.consultwho.com/a4.asphttp://www.consultwho.com/a4.asphttp://www.consultwho.com/a4.asphttp://www.consultwho.com/a4.asphttp://www.onlineclothingstudy.com/2012/01/traffic-light-system-for-quality.htmlhttp://www.leadtec.com/images/stories/whitepapers/joseph%20abboud%20case%20study.pdf


7/7

motivation can be improve by sharing certain percentage of you profit made from operators

extra effort.

20. Plan for operators Incentive scheme: Paul Collyer, British expert says In British factories,

in a non incentive environment factory can reach up to 80% efficiency level and if managerexpect more than that they had to provide incentive to operators as well as to the supporting

team. Ifwe look into Asian factories, in a non incentive environment factories find it is very

difficult to reach up to 40% efficiency. You can see the potential efficiency that can be

converted in money.

You need to understand that employees come for work in your organization for money. Initially

you may think that an incentive scheme may reduce your profit. But in real it works in opposite

direction, provided that incentive system is fair for the workers and has been implemented

intelligently. I have seen factories where operator efficiency reaches up to 76% from 45% afterimplementation of incentive scheme. An incentive scheme will give lot of other benefits in

return as a byproduct. An incentive scheme designed with multiple parameters may bring

discipline on the shop floor. As operators give extra effort to the work, efficiency as well as

productivity of the operator increases.

Related articles

How to stop missing of garments in production processes?

Difficulties in Managing Smaller Garment Export Orders

Bangalore Tank - A Case Study of Garment Order Processing
http://www.onlineclothingstudy.com/2011/08/how-to-stop-missing-of-garments-in.htmlhttp://www.onlineclothingstudy.com/2011/02/how-to-manage-small-orders.htmlhttp://www.onlineclothingstudy.com/2011/03/tale-of-tank-top.htmlhttp://www.onlineclothingstudy.com/2012/02/20-ways-to-improve-productivity-in.htmlhttp://www.onlineclothingstudy.com/2011/03/tale-of-tank-top.htmlhttp://www.onlineclothingstudy.com/2011/02/how-to-manage-small-orders.htmlhttp://www.onlineclothingstudy.com/2011/08/how-to-stop-missing-of-garments-in.html

20 ways to improve productivity in garment production.docx

Documents