17 decal placement omanuals.hobbico.com/rmx/85-5858.pdf · 2018. 7. 19. · dornier do 335 was...
TRANSCRIPT
decal placement17
Light Blue
Dark Green
Brown-Violet
Black Green
Dark Gray
Light Gray
Silver
Gunmetal
Rust
Red
White
Flat Black
* REPEAT SEVERAL TIMES* A REPETER PLUSIEURS FOIS
* CEMENT TOGETHER* A COLLER
* ALTERNATIVE ASSEMBLY* ENSEMBLAGE ALTERNATIVE
* REMOVE AND THROW AWAY* A RETIRER ET JETER
* DO NOT CEMENT* NE PAS COLLER
* OPTIONAL PARTS* PIECES EN OPTION
* DECAL * DECAL COMANIE
this paint guide is provided to complete this kit as shown on the box.
Ce guide de peintures est fourni pour reproduire le modèle réduit qui apparaît sur la boîte.
Bleu Clair
Vert foncé
Violet-brun
Vert noir
Gris foncé
Gris clair
Argent
Bronze
Rouille
Rouge
Blanc
Noir mat
* Study the assembly drawings.* Each plastic part is identified by a number.* In the assembly drawings, some parts will be
marked by a star (★) to indicate chrome plated plastic.
* For better paint and decal adhesion, wash the plastic parts in a mild detergent solution. Rinse and let air dry.
* Check the fit of each piece before cementing in place.
* Use only cement for polystyrene plastic.* Scrape plating and paint from areas
to be cemented.* Allow paint to dry thoroughly before
handling parts.* Any unused parts may be discarded.
decal applIcatIOn InStRUctIOnS
1. Cut desired decal from sheet.2. Dip decal in water for a few seconds.3. Place wet decal on paper towel.4. Wait until decal is movable on paper backing.5. Place decal in position on model, face up and
slide backing away.6. Press out air bubbles with a soft damp cloth.7. Milkiness that may appear is for better decal
adhesion and will dry clear. Wipe away any excess adhesive.
8. Do not touch decal until fully dry.9. Allow the decals 48 hours to dry before
applying clear coat.
nOte: decals are compatible with setting solutions or solvents.
Read tHIS BeFORe YOU BeGIn lIRe ce QUI SUIt aVant de cOmmenceR
* Etudier les schémas de montage.* Chaque pièce en plastique est identifiée par un numéro.* Sur les schémas de montage, certaines pièces sont
marquées d'une étoile (★) pour indiquer qu'elles sont en plastique chromé.
* Pour une meilleure prise de la peinture et des autocollants, laver les pièces en plastique avec une solution détergente peu concentrée. Les rincer et les laisser sécher à l'air.
* Vérifier que chaque pièce s'ajuste bien avant de la coller en place.
* N'utiliser que de la colle pour polystyrène.* Gratter les parties à coller pour enlever le chrome et la peinture.* Laisser la peinture bien sécher avant de manipuler les pièces.* Toute pièce inutilisée peut être jetée.
dIRectIVeS d'applIcatIOn deS aUtOcOllantS
1. Découper l'autocollant désiré de la feuille.2. Tremper l'autocollant dans de l'eau pendant quelques secondes.3. Placer l'autocollant mouillé sur une serviette en papier.4. Attendez que l'autocollant puisse être déplacé sur son
support en papier.5. Mettre l'autocollant en position sur le modèle face sur
le dessus et faire glisser le support pour l'enlever.6. Appuyer avec un chiffon doux humide pour éliminer les bulles d'air.7. La substance laiteuse qui peut apparaître est destinée à
améliorer l'adhésion de l'autocollant et devient incolore au séchage. Essuyer pour enlever tout excédent d'adhésif.
8. Ne pas toucher l'autocollant tant qu'il n'est pas bien sec.9. Laisser l'autocollant sécher pendant 48 heures avant
d'appliquer une couche transparente.
RemaRQUe: les autocollants sont compatibles avec les solutions de fixage ou les solvants.
dORnIeR dO 335 aRROw KIT 5858 85585800200
If you have any questions or comments, call our hotline at: (800) 833-3570or, please write to:
Revell Inc Consumer Service Department, 1850 Howard Street Unit A, Elk Grove Village, Illinois 60007Be sure to include the plan number (85585800200), part number, description, your return address and phone number.
Visit our website: www.revell.com
Revell Inc Elk Grove Village, IL. Copyright © 2009. All rights reserved.Kit 5858 - Page 12
One of several advanced fighter designs under development by the Luftwaffe at the end of WWII, the Dornier DO 335 was characterized by it's unusual engine placement. With the engines located at each end of the fuselage it had a considerable reduction in wind drag, thus allowing speeds in excess of 470 miles per hour. The DO 335 was one of the fast-est propeller driven aircraft ever built. Your Revell model features detailed engines with optional open or closed fuselage access panels and mov-able wing flaps, optional single or tandem seat versions with three figures and authentic decal mark-ings for 4 varients is also included.
FUSelaGe aSSemBlY1 decal placement16
Kit 5858 - Page 2 Kit 5858 - Page 11
A
C
D
E
B
52SCOOP
TOP HALF43
SCOOPBOTTOM HALF
1RIGHT
FUSELAGE HALF
1RIGHT
FUSELAGE HALF
27 LEFT
FUSELAGE HALF
26UPPER FUSELAGE
DECKING
37COWLING
TAB INTOSLOT
SLOTCEMENT ONLY HERE
RUST
RUST
9RIGHT FORWARD
FLAME HIDERFLAT BLACK
MAKE FLUSHWITH THIS EDGE
28AFT FLAME HIDER
FLAT BLACK
BOLTS: SILVER
BOLTS: SILVER
TUBING: SILVER
TUBING: WHITE,RED,
BROWN AND GREEN
EXHAUSTS: RUST
EXHAUSTS: RUST
DARK GRAYBLACK BACKGROUND
BLACK BACKGROUNDGUNMETAL
SHAFT: SILVERENGINE AND MOUNTS: LIGHT GRAY
ENGINE AND MOUNTS: MEDIUM GRAY
REAR ENGINE PAINT DETAIL
FRONT ENGINE PAINT DETAIL
Do 335 V-10 VERSION
Do 335 V-10 VERSION ONLY
Do 335 V-10 VERSION ONLY
REMOVE BUMP ON FUSELAGE HALF 1 AND
ENGINE DOOR 35
enGIne dOOR / FInal aSSemBlY14
FIGUReS15
FROnt cOckpIt aSSemBlY2
Kit 5858 - Page 10 Kit 5858 - Page 3
PAINT DETAIL:BLACK PANEL WITH SILVER DIAL OUTLINES
Paint hands and faces: FLESH COLOR. Shirts: WHITE. Uniform and Caps: CHARCOAL GRAY. Ammunition Belt: SILVER. Shoes: BLACK. Can and Wrench: STEEL
15LEFT FORWARDFLAME HIDER
FLAT BLACK
44SCOOP
TOP HALF
51SCOOP
BOTTOM HALF
40KNEELING MECHANIC
41STANDING MECHANIC
92PILOT
28AFT
FLAME HIDERFLAT BLACK
SILVER HOUSING.BLACK FACE
42REAR ENGINE
COVERLIGHT GRAY
(INSIDE)
35FRONT ENGINE
COVERLIGHT GRAY
(INSIDE)
29TAIL SUPPORT
21CONTROL COLUMN
AND YOKEFLAT BLACK
25HEADRESTDARK BROWN
DECAL1
46REAR BULKHEAD AND SEAT BACK
FLAT BLACK
36COCKPIT FLAT BLACK
69NOSE GEAR WELLLIGHT GRAY INTERIOR
(TOP AND SIDES FLAT BLACK)
60FUSELAGE
TOP
GRAY STRAPS WITH
SILVER BUCKLES
BLACK CONSOLE WITH
SILVER DETAILS
BLACK CONSOLE WITH
SILVER DETAILS
PAINT INSIDE COCKPIT AREA
FLAT BLACK
SILVER
SILVER
RED
LIGHTGRAY
39INSTRUMENT PANEL
Do 335 V-10 VERSION ONLY
REMOVE BUMP
Do 335 V-10 VERSION ONLY
Do 335 A-O VERSION
20TRIM WHEEL
FLAT BLACK
RIGHT SIDE
ReaR cOckpIt aSSemBlY3
lOweR wInG aSSemBlY4
canOpY aSSemBlY13
Kit 5858 - Page 4 Kit 5858 - Page 9
Do 335 A-O VERSION
Do 335 V-10 VERSION
OPEN CANOPIES
PAINT DETAIL:BLACK WITH SILVER
DIAL OUTLINES
Do 335 V-10 VERSION
Do 335 V-10 VERSION
68INSTRUMENT PANEL
25HEADRESTDARK BROWN
75WINDSCREEN
CLEAR
75WINDSCREEN
CLEAR
77AFT WINDSCREEN
CLEAR
76CANOPY
CLEAR(CANOPY FRAME IS TO
MATCH FUSELAGE COLOR}
76CANOPY
CLEAR
78AFT CANOPY
CLEAR
19ANTENNA
19ANTENNA
34REAR BULKHEAD AND SEAT BACK
FLAT BLACK
GRAY STRAPS WITH
SILVER BUCKLES
61FUSELAGE TOP
SILVER
73WING BOTTOM
Do 335 V-10 VERSION
Do 335 V-10 VERSION
50COCKPIT FLAT BLACK
BLACK CONSOLE WITH
SILVER DETAILS
RED
BLACK CONSOLE WITH
SILVER DETAILS
StaBIlIZeR aSSemBlY11
pROpelleR aSSemBlY12
UppeR wInG aSSemBlY5
Intake cOVeR aSSemBlY6
Kit 5858 - Page 5Kit 5858 - Page 8
FRONT
REAR
18 STABILIZER TOP
12 STABILIZER TOP
13 STABILIZER
BOTTOM
22 STABILIZER
BOTTOM
RIGHT LEFT 16RIGHT
WING TOP
10LEFT
WING TOP
TAPESTRETCH TAPE FROM ONE WING
TIP TO THE OTHER AS SHOWN. THIS ACHIEVES THE
PROPER DIHEDRAL (WING ANGLE TO THE FUSELAGE)
WHILE THE GLUE IS DRYING.
38FLAP TOP
64FLAP BOTTOM
RIGHT
48FLAP TOP
62FLAP BOTTOM
LEFT
8INTAKE
LIGHT GRAY
LIGHT GRAY
11FRONT
PROPELLERBLACK GREEN
WITH SILVER HUB
17REAR
PROPELLER-BLACK GREEN
WITH SILVER HUB
67FRONT
SPINNERBLACK GREEN
66REAR
SPINNERBLACK GREEN
33FRONT
SPINNER PLATEBLACK GREEN
32REAR
SPINNER PLATEBLACK GREEN
nOSe wHeel / StRUt aSSemBlY7
maIn wHeel / StRUt aSSemBlY8
InneR dOOR aSSemBlY9
antenna / dOOR aSSemBlY10
Kit 5858 - Page 6 Kit 5858 - Page 7
24LEFT
MAIN GEAR STRUTLIGHT GRAY
(SHADED AREA, SILVER)
45LEFT
MAIN GEAROUTER DOOR
LIGHT GRAY(INSIDE)
47RIGHT
MAIN GEAROUTER DOOR
LIGHT GRAY(INSIDE)
23RIGHT
MAIN GEAR STRUTLIGHT GRAY
(SHADED AREA, SILVER)
2LEFT
GEAR DOORLIGHT GRAY
(INSIDE ONLY)
79LANDING LIGHT
LENSCLEAR
53RADAR ANTENNA
DARK GRAY
53RADAR ANTENNA
DARK GRAY
5LEFT
INNER DOORLIGHT GRAY
(INSIDE ONLY)
63 DOOR STRUT
LIGHT GRAY
63 DOOR STRUT
LIGHT GRAY
3RIGHT
GEAR DOORLIGHT GRAY
(INSIDE ONLY)
6RIGHT
INNER DOORLIGHT GRAY
(INSIDE ONLY)
49RETRACTION
STRUTSLIGHT GRAY
30TORQUE LINK
LIGHT GRAY
30TORQUE LINK
LIGHT GRAY
55RIGHT
NOSE WHEEL HALFFLAT BLACK
54LEFT
NOSE WHEEL HALFFLAT BLACK
DARK GRAY
57INNER MAIN
WHEEL HALFFLAT BLACK
56OUTER MAIN WHEEL HALF
FLAT BLACK
DARK GRAY
RED
RED
WHITE
WHITE
WHITE
WHITE
65NOSE GEAR STRUT
LIGHT GRAY(SHADED AREA, SILVER)
4MUD GUARD
LIGHT GRAY
7RETRACTION
STRUTLIGHT GRAY
70TORQUE LINK
LIGHT GRAY
Do 335 V-10 VERSION
Do 335 V-10 VERSION
NOTE:BE SURE FLATTENED SIDE OF TIRES IS FLAT ON THE
SURFACE WHEN GLUING THE MAIN GEAR TIRES.
ON #4 SHOW DIRECTON ARROW POINTING TOWARDS NOSE WHEEL
nOSe wHeel / StRUt aSSemBlY7
maIn wHeel / StRUt aSSemBlY8
InneR dOOR aSSemBlY9
antenna / dOOR aSSemBlY10
Kit 5858 - Page 6 Kit 5858 - Page 7
24LEFT
MAIN GEAR STRUTLIGHT GRAY
(SHADED AREA, SILVER)
45LEFT
MAIN GEAROUTER DOOR
LIGHT GRAY(INSIDE)
47RIGHT
MAIN GEAROUTER DOOR
LIGHT GRAY(INSIDE)
23RIGHT
MAIN GEAR STRUTLIGHT GRAY
(SHADED AREA, SILVER)
2LEFT
GEAR DOORLIGHT GRAY
(INSIDE ONLY)
79LANDING LIGHT
LENSCLEAR
53RADAR ANTENNA
DARK GRAY
53RADAR ANTENNA
DARK GRAY
5LEFT
INNER DOORLIGHT GRAY
(INSIDE ONLY)
63 DOOR STRUT
LIGHT GRAY
63 DOOR STRUT
LIGHT GRAY
3RIGHT
GEAR DOORLIGHT GRAY
(INSIDE ONLY)
6RIGHT
INNER DOORLIGHT GRAY
(INSIDE ONLY)
49RETRACTION
STRUTSLIGHT GRAY
30TORQUE LINK
LIGHT GRAY
30TORQUE LINK
LIGHT GRAY
55RIGHT
NOSE WHEEL HALFFLAT BLACK
54LEFT
NOSE WHEEL HALFFLAT BLACK
DARK GRAY
57INNER MAIN
WHEEL HALFFLAT BLACK
56OUTER MAIN WHEEL HALF
FLAT BLACK
DARK GRAY
RED
RED
WHITE
WHITE
WHITE
WHITE
65NOSE GEAR STRUT
LIGHT GRAY(SHADED AREA, SILVER)
4MUD GUARD
LIGHT GRAY
7RETRACTION
STRUTLIGHT GRAY
70TORQUE LINK
LIGHT GRAY
Do 335 V-10 VERSION
Do 335 V-10 VERSION
NOTE:BE SURE FLATTENED SIDE OF TIRES IS FLAT ON THE
SURFACE WHEN GLUING THE MAIN GEAR TIRES.
ON #4 SHOW DIRECTON ARROW POINTING TOWARDS NOSE WHEEL
StaBIlIZeR aSSemBlY11
pROpelleR aSSemBlY12
UppeR wInG aSSemBlY5
Intake cOVeR aSSemBlY6
Kit 5858 - Page 5Kit 5858 - Page 8
FRONT
REAR
18 STABILIZER TOP
12 STABILIZER TOP
13 STABILIZER
BOTTOM
22 STABILIZER
BOTTOM
RIGHT LEFT 16RIGHT
WING TOP
10LEFT
WING TOP
TAPESTRETCH TAPE FROM ONE WING
TIP TO THE OTHER AS SHOWN. THIS ACHIEVES THE
PROPER DIHEDRAL (WING ANGLE TO THE FUSELAGE)
WHILE THE GLUE IS DRYING.
38FLAP TOP
64FLAP BOTTOM
RIGHT
48FLAP TOP
62FLAP BOTTOM
LEFT
8INTAKE
LIGHT GRAY
LIGHT GRAY
11FRONT
PROPELLERBLACK GREEN
WITH SILVER HUB
17REAR
PROPELLER-BLACK GREEN
WITH SILVER HUB
67FRONT
SPINNERBLACK GREEN
66REAR
SPINNERBLACK GREEN
33FRONT
SPINNER PLATEBLACK GREEN
32REAR
SPINNER PLATEBLACK GREEN
ReaR cOckpIt aSSemBlY3
lOweR wInG aSSemBlY4
canOpY aSSemBlY13
Kit 5858 - Page 4 Kit 5858 - Page 9
Do 335 A-O VERSION
Do 335 V-10 VERSION
OPEN CANOPIES
PAINT DETAIL:BLACK WITH SILVER
DIAL OUTLINES
Do 335 V-10 VERSION
Do 335 V-10 VERSION
68INSTRUMENT PANEL
25HEADRESTDARK BROWN
75WINDSCREEN
CLEAR
75WINDSCREEN
CLEAR
77AFT WINDSCREEN
CLEAR
76CANOPY
CLEAR(CANOPY FRAME IS TO
MATCH FUSELAGE COLOR}
76CANOPY
CLEAR
78AFT CANOPY
CLEAR
19ANTENNA
19ANTENNA
34REAR BULKHEAD AND SEAT BACK
FLAT BLACK
GRAY STRAPS WITH
SILVER BUCKLES
61FUSELAGE TOP
SILVER
73WING BOTTOM
Do 335 V-10 VERSION
Do 335 V-10 VERSION
50COCKPIT FLAT BLACK
BLACK CONSOLE WITH
SILVER DETAILS
RED
BLACK CONSOLE WITH
SILVER DETAILS
enGIne dOOR / FInal aSSemBlY14
FIGUReS15
FROnt cOckpIt aSSemBlY2
Kit 5858 - Page 10 Kit 5858 - Page 3
PAINT DETAIL:BLACK PANEL WITH SILVER DIAL OUTLINES
Paint hands and faces: FLESH COLOR. Shirts: WHITE. Uniform and Caps: CHARCOAL GRAY. Ammunition Belt: SILVER. Shoes: BLACK. Can and Wrench: STEEL
15LEFT FORWARDFLAME HIDER
FLAT BLACK
44SCOOP
TOP HALF
51SCOOP
BOTTOM HALF
40KNEELING MECHANIC
41STANDING MECHANIC
92PILOT
28AFT
FLAME HIDERFLAT BLACK
SILVER HOUSING.BLACK FACE
42REAR ENGINE
COVERLIGHT GRAY
(INSIDE)
35FRONT ENGINE
COVERLIGHT GRAY
(INSIDE)
29TAIL SUPPORT
21CONTROL COLUMN
AND YOKEFLAT BLACK
25HEADRESTDARK BROWN
DECAL1
46REAR BULKHEAD AND SEAT BACK
FLAT BLACK
36COCKPIT FLAT BLACK
69NOSE GEAR WELLLIGHT GRAY INTERIOR
(TOP AND SIDES FLAT BLACK)
60FUSELAGE
TOP
GRAY STRAPS WITH
SILVER BUCKLES
BLACK CONSOLE WITH
SILVER DETAILS
BLACK CONSOLE WITH
SILVER DETAILS
PAINT INSIDE COCKPIT AREA
FLAT BLACK
SILVER
SILVER
RED
LIGHTGRAY
39INSTRUMENT PANEL
Do 335 V-10 VERSION ONLY
REMOVE BUMP
Do 335 V-10 VERSION ONLY
Do 335 A-O VERSION
20TRIM WHEEL
FLAT BLACK
RIGHT SIDE
FUSelaGe aSSemBlY1 decal placement16
Kit 5858 - Page 2 Kit 5858 - Page 11
A
C
D
E
B
52SCOOP
TOP HALF43
SCOOPBOTTOM HALF
1RIGHT
FUSELAGE HALF
1RIGHT
FUSELAGE HALF
27 LEFT
FUSELAGE HALF
26UPPER FUSELAGE
DECKING
37COWLING
TAB INTOSLOT
SLOTCEMENT ONLY HERE
RUST
RUST
9RIGHT FORWARD
FLAME HIDERFLAT BLACK
MAKE FLUSHWITH THIS EDGE
28AFT FLAME HIDER
FLAT BLACK
BOLTS: SILVER
BOLTS: SILVER
TUBING: SILVER
TUBING: WHITE,RED,
BROWN AND GREEN
EXHAUSTS: RUST
EXHAUSTS: RUST
DARK GRAYBLACK BACKGROUND
BLACK BACKGROUNDGUNMETAL
SHAFT: SILVERENGINE AND MOUNTS: LIGHT GRAY
ENGINE AND MOUNTS: MEDIUM GRAY
REAR ENGINE PAINT DETAIL
FRONT ENGINE PAINT DETAIL
Do 335 V-10 VERSION
Do 335 V-10 VERSION ONLY
Do 335 V-10 VERSION ONLY
REMOVE BUMP ON FUSELAGE HALF 1 AND
ENGINE DOOR 35
decal placement17
Light Blue
Dark Green
Brown-Violet
Black Green
Dark Gray
Light Gray
Silver
Gunmetal
Rust
Red
White
Flat Black
* REPEAT SEVERAL TIMES* A REPETER PLUSIEURS FOIS
* CEMENT TOGETHER* A COLLER
* ALTERNATIVE ASSEMBLY* ENSEMBLAGE ALTERNATIVE
* REMOVE AND THROW AWAY* A RETIRER ET JETER
* DO NOT CEMENT* NE PAS COLLER
* OPTIONAL PARTS* PIECES EN OPTION
* DECAL * DECAL COMANIE
this paint guide is provided to complete this kit as shown on the box.
Ce guide de peintures est fourni pour reproduire le modèle réduit qui apparaît sur la boîte.
Bleu Clair
Vert foncé
Violet-brun
Vert noir
Gris foncé
Gris clair
Argent
Bronze
Rouille
Rouge
Blanc
Noir mat
* Study the assembly drawings.* Each plastic part is identified by a number.* In the assembly drawings, some parts will be
marked by a star (★) to indicate chrome plated plastic.
* For better paint and decal adhesion, wash the plastic parts in a mild detergent solution. Rinse and let air dry.
* Check the fit of each piece before cementing in place.
* Use only cement for polystyrene plastic.* Scrape plating and paint from areas
to be cemented.* Allow paint to dry thoroughly before
handling parts.* Any unused parts may be discarded.
decal applIcatIOn InStRUctIOnS
1. Cut desired decal from sheet.2. Dip decal in water for a few seconds.3. Place wet decal on paper towel.4. Wait until decal is movable on paper backing.5. Place decal in position on model, face up and
slide backing away.6. Press out air bubbles with a soft damp cloth.7. Milkiness that may appear is for better decal
adhesion and will dry clear. Wipe away any excess adhesive.
8. Do not touch decal until fully dry.9. Allow the decals 48 hours to dry before
applying clear coat.
nOte: decals are compatible with setting solutions or solvents.
Read tHIS BeFORe YOU BeGIn lIRe ce QUI SUIt aVant de cOmmenceR
* Etudier les schémas de montage.* Chaque pièce en plastique est identifiée par un numéro.* Sur les schémas de montage, certaines pièces sont
marquées d'une étoile (★) pour indiquer qu'elles sont en plastique chromé.
* Pour une meilleure prise de la peinture et des autocollants, laver les pièces en plastique avec une solution détergente peu concentrée. Les rincer et les laisser sécher à l'air.
* Vérifier que chaque pièce s'ajuste bien avant de la coller en place.
* N'utiliser que de la colle pour polystyrène.* Gratter les parties à coller pour enlever le chrome et la peinture.* Laisser la peinture bien sécher avant de manipuler les pièces.* Toute pièce inutilisée peut être jetée.
dIRectIVeS d'applIcatIOn deS aUtOcOllantS
1. Découper l'autocollant désiré de la feuille.2. Tremper l'autocollant dans de l'eau pendant quelques secondes.3. Placer l'autocollant mouillé sur une serviette en papier.4. Attendez que l'autocollant puisse être déplacé sur son
support en papier.5. Mettre l'autocollant en position sur le modèle face sur
le dessus et faire glisser le support pour l'enlever.6. Appuyer avec un chiffon doux humide pour éliminer les bulles d'air.7. La substance laiteuse qui peut apparaître est destinée à
améliorer l'adhésion de l'autocollant et devient incolore au séchage. Essuyer pour enlever tout excédent d'adhésif.
8. Ne pas toucher l'autocollant tant qu'il n'est pas bien sec.9. Laisser l'autocollant sécher pendant 48 heures avant
d'appliquer une couche transparente.
RemaRQUe: les autocollants sont compatibles avec les solutions de fixage ou les solvants.
dORnIeR dO 335 aRROw KIT 5858 85585800200
If you have any questions or comments, call our hotline at: (800) 833-3570or, please write to:
Revell Inc Consumer Service Department, 1850 Howard Street Unit A, Elk Grove Village, Illinois 60007Be sure to include the plan number (85585800200), part number, description, your return address and phone number.
Visit our website: www.revell.com
Revell Inc Elk Grove Village, IL. Copyright © 2009. All rights reserved.Kit 5858 - Page 12
One of several advanced fighter designs under development by the Luftwaffe at the end of WWII, the Dornier DO 335 was characterized by it's unusual engine placement. With the engines located at each end of the fuselage it had a considerable reduction in wind drag, thus allowing speeds in excess of 470 miles per hour. The DO 335 was one of the fast-est propeller driven aircraft ever built. Your Revell model features detailed engines with optional open or closed fuselage access panels and mov-able wing flaps, optional single or tandem seat versions with three figures and authentic decal mark-ings for 4 varients is also included.