15 tft-lcd tv/monitor model: tlm1510eudiagramas.diagramasde.com/otros/tlm-1510eu.pdf · 2013. 3....

DESIGNS AND SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE

SERVICE MANUALSERVICE MANUAL

15" TFT-LCD TV/MONITOR

MODEL: TLM1510EU

-2-

TABLE OF CONTENTS

Location and Function of Controls --------------------------------------------------------------- 3

Remote controller ---------------------------------------------------------------------------------- 3

Front Panel Control -------------------------------------------------------------------------------- 5

Installation and connecting ------------------------------------------------------------------------ 6

Schematic Diagrams ---------------------------------------------------------------------------------- 7

AUDIO Schematic Circuit ------------------------------------------------------------------------- 7

DRIVE Schematic Circuit ------------------------------------------------------------------------- 8

OUTPUT Schematic Circuit ---------------------------------------------------------------------- 10

KEY Board Circuit ----------------------------------------------------------------------------------- 11

TUNER Schematic Circuit ------------------------------------------------------------------------ 12

TELETEXT Schematic Circuit ------------------------------------------------------------------- 13

Printed Circuit Board ------------------------------------------------------------------------------- 14

AUDIO Board -------------------------------------------------------------------------------------- 14

DRIVE Board -------------------------------------------------------------------------------------- 16

INPUT Board -------------------------------------------------------------------------------------- 18

TUNER/KEY/SPEAKER OUT Board --------------------------------------------------------- 19

TELETEXT Board -------------------------------------------------------------------------------- 20

Block Diagram ----------------------------------------------------------------------------------------- 22

Wiring Diagram --------------------------------------------------------------------------------------- 23

Exploded View and Mechanical Parts List ---------------------------------------------------- 24

JTM152 Explode view ---------------------------------------------------------------------------- 24

TV Body Explode View --------------------------------------------------------------------------- 25

Speaker Box Explode view ---------------------------------------------------------------------- 26

Base Stand Explode view ----------------------------------------------------------------------- 27

Information Of ICs ----------------------------------------------------------------------------------- 28

PCB Component List -------------------------------------------------------------------------------- 34

AUDIO PCB Assembly --------------------------------------------------------------------------- 34

DRIVE PCB Assembly --------------------------------------------------------------------------- 36

Electronic Common Part Assembly ----------------------------------------------------------- 38

Tuning PCB Assembly --------------------------------------------------------------------------- 39

INPUT PCB Assembly --------------------------------------------------------------------------- 39

Control Key PCB Assembly -------------------------------------------------------------------- 39

Speaker OUT PCB Assembly ------------------------------------------------------------------ 40

TELETEXT PCB Assembly --------------------------------------------------------------------- 40

All the functions can be controlled with the remote controller. Some functions can also be adjusted with the buttons on the front panel of the set.

Remote controller

1. STANDBY To switch the unit from on to off or off to on.

2. SOURCE To Select TV, AV (Video/S-Video/RGB)

or PC monitor mode.

3. NUMBER BUTTONS To directly select programme number.

4. TWO-DIGIT NUMBER BUTTON To switch one or two-digit programme

number

5. RETURN To return to previously selected

programme number .

6. PICTURE To select picture control (brightness/contrast/color).

8. MENUTo enter into or exit out of the menu (AV/TV mode).To accept your selection (PC mode).

SOURCE DISPLAY MUTE

1 2 3 4

5 6 7

9

8

0RETURN

MENU

PICTURE MODE SOUND

BBE

NICAM/A2SYSTEM

TEXT MIX HOLD INDEX

CANCEL SIZE REVEAL SUBPAGE

RED GREEN YELLOW CYAN

STANDBY

1

2

3

4

67

5

8UPSIDE

9

9. UPSIDETo turn picture upside down.

Location and Function of Controls

-3-

7. (VOLUME UP/DOWN)

To increase or decrease the volume.To adjust menu settings. (PROGRAMME UP/DOWN)To select programme or a menu item.

10. MUTE To switch on sound mute or turn off sound mute.

11. DISPLAY To display setup information channel.

12. MODE BUTTON To adjust the picture mode (user/soft/dynamic/stanard).

13. SOUND BUTTONTo adjust the sound effect.

14. BBE BUTTON To switch BBE on or off.

15. SYSTEMTo select TV system.

16. NICAM/A2 BUTTON (OPTION)To switch between NICAM , A2 and mono sound output.

17. TELETEXT BUTTONS (OPTION)

These buttons are used for teletext.For further details, see the 'Teletext'section.

SOURCE DISPLAY MUTE

1 2 3 4

5 6 7

9

8

0RETURN

MENU

PICTURE MODE SOUND

BBE

NICAM/A2SYSTEM

TEXT MIX HOLD INDEX

CANCEL SIZE REVEAL SUBPAGE

RED GREEN YELLOW CYAN

STANDBY

10

11

12

13

1516

14

17

UPSIDE

-4-



-5-

This TFT-LCD TV/monitor allows you to easily adjust the characteristics of the

image being displayed. While you use these buttons to adjust the controls, and OSD shows you their numeric values as they change.

Front Panel Control

SOURCE MENU CH VOL

1 2 3 4 7 85 6

There are 7 keys for user's control including "POWER", "SOURCE", "MENU",

" CH- ", " CH+ ", " VOL- " and " VOL+ ". The following descriptions are the

introduction of these keys.

Turns ON/OFF the LCD TV/monitor.When there is no signal input from PC port, after 20 seconds, the machine will go to standby mode automatically, on the other hand if the input port is TV/AV, and there is no signal input until 15 minutes, the machine will go to standby mode automatically also, the indicator of the power will turn to green. If you want to power on the machine again, please press power button.

Select video sources (Video/S-video/TV) or PC sources.

Enter or back to menu.

When you watch the TV program, push the button to increase channel number. In the main-menu, push the button to select the upward menu item.

Decreases/adjusts the values of the selected menu item, or decreases the level of audio volume.

When you watch the TV program, push the button to decrease channel number. In the main-menu, push the button to select the downward menu item.

Description

Increases/adjusts the values of the selected menu item, or increases the level of audio volume.

POWER

SOURCE

MENU

Name

1

3

4

5

6

7

Item

2

8

Remote control sensor

Figure Cable connections

Connecting your LCD TV/PC monitor

Installation and connecting

-6-

1.Connect the speaker cable to "Speaker" port (Please refer to page 28).

2.Connect the stereo cable to "Line-out" of your computer.

3.Connect the audio sources (DVD, VCR or Camcorder) to proper L, R of AV IN ports.

4. Connect the video source (DVD, VCR or Camcorder) to proper VIDEO of AV IN ports.

5.Connect the S-video cable to your DVD, VCR or Camcorder.

6.Connect the power cord to the DC adapter and connect the adapter jack to the DC12V

power port on the back of your monitor.

7.Connect the Euro scart connector to the Euro scart socket of your TV/monitor.

8.Connect the signal cable to the VGA port of your monitor.

9.Connect antenna or CATV cable to "Antenna" port.

NOTE:

1.Do not plug in the power cord until all connections you desired have been completed.

2.When connecting a video source via scart connector, please press the "SOURCE" button

on remote control or front panel to select the RGB or AV mode.

AV IN

SC

AR

T

R L VIDEO DC INS-VIDEOLINE INSPEAKER

PC

21 3 7 8

PC

9

DVD or VCR

4 5 6

Figu

re 1

-1 A

UD

IO S

chem

atic

Circ

uit

Schematic Diagram

-7-

a a

a a

Schematic Diagram

Figure 1-2.1 DRIVE Schematic Circuit

-8-

a a

a a

Schematic Diagram

-9-

Figu

re 1

-2.2

DR

IVE

Sche

mat

ic C

ircui

t

a a

-10-

Schematic Diagram

Figure 1-3 OUTPUT Schematic Circuit

-11-

Figu

re 1

-4 K

EY S

chem

atic

Circ

uit

Schematic Diagram

a a

a a

-12-

Schematic Diagram

Figu

re 1

-5 T

UN

ER S

chem

atic

Circ

uit

a a

a a

Figu

re 1

-6 T

ELET

EXT

Sche

mat

ic C

ircui

t

-13-

Schematic Diagram

a a

-14-

Printed Circuit Board

Figure 2-1.1 AUDIO Board (Top Side)

-15-


Figure 2-1.2 AUDIO Board (Bottom Side)


Figure 2-2.1 DRIVE Board (Top Side)

-16-

-17-


Figure 2-2.2 DRIVE Board (Bottom Side)

-18-


Figure 2-3 INPUT Board

Figu

re 2

-4 T

UN

ER/K

EY/S

PEAK

ER O

UT

Boar

d

-19-


a a

-20-


Figure 2-5.1 TELETEXT Board (Top Side)

-21-


Figure 2-5.2 TELETEXT Board (Bottom Side)

Block Diagram

Fig

ure

3-1

Blo

ck D

iag

ram

-22-

a a

a a

Figu

re 3

-2 W

iring

Dia

gram

Wiring Diagram

-23-

ADAP

TOR

a a

Exploded View and Mechanical Parts List

-24-

1

2

3

4

5

ITEM QTYDescription

1

2

3

4

5

TV BODY

SPEAKER BOX

SPEAKER BRACKET

AXES COVER

BASE STAND

1

2

2

1

1

JTM152 Explode View

TV

Bo

dy

Ex

plo

de

vie

w

PA

NE

L S

OC

KE

T B

RA

CK

ET

QT

YD

es

cri

pti

on

9C

AB

INE

T F

RO

NT

FU

NC

TIO

N K

EY

FU

NC

TIO

N P

CB

RE

MO

TE

CO

NT

RO

L L

EN

S

PO

WE

R B

UT

TO

N

PO

WE

R P

CB

LC

D

1 1 1 1 1 1 1 1L

CD

CA

B. B

AC

K

ITE

MQ

TY

De

sc

rip

tio

n

1 1 1 1 1 1 1 1

ITE

MD

es

cri

pti

on

19

20 21

23

24

BR

AS

S P

OL

E I

CA

BIN

ET

BA

CK

BR

AS

S P

OL

E II

22

10 11 12

14

15

16

13

17

18

INP

UT

/OU

TP

UT

JA

CK

SH

IEL

D

45

3

6

7

16

8

17

18

111

2

19

20

21

13

14

10

15

23

9

22

12

24

CA

BL

E C

LA

MP

FIB

RE

WA

SH

ER

INV

ER

TE

R P

CB

INP

UT

PC

B

AU

DIO

PC

B

DR

IVE

PC

B

SH

IEL

D C

OV

ER

II

TU

NE

R W

IRE

BR

AC

KE

T

TU

NE

R B

OX

TU

NE

R B

OX

CO

VE

R

SH

IEL

D C

OV

ER

I


ITE

M

1 2 3 4 5 6 7 8

QT

Y

1 1 1 1 1 1 1 1

-25-


-26-

1

2

3 4

5

ITEM QTYDescription

1

2

3

4

5

SPEAKER CAB. BACK

SPEAKER

SPEAKER STAND HOLDER

SPEAKER TERMINAL

SPEAKER CAB. FRONT

1

1

2

1

1

Speaker Box Explode View


-27-

2

3

4

5

6

7

CONTROL PLACE PLATE I

SPRING

WASHER

AXES HOLDER I

NUT

2

1

10

6

2

2

9

10

11

12

BASE STAND COVER I

BASE STAND COVER II

BASE STAND

METAL STAND BASE

ITEM QTYDescription

1

AXES

1

ITEM QTYDescription

8 AXES HOLDER II 1

1

1

1

1

Base Stand Explode View

9

8

10

12

11

13

45

6

7

1

2

3

CONTROL PLACE PLATE II

13 STAND CUSHION 1

Pin No. Pin Name Function Pin No. Pin Name Function1 B1/CB1IN Blue1/Cb1 Analog Component Input 41 C7 Picture Bus Chroma (MSB)2 G1/Y1IN Green1/Y1 Analog Component Input 42 C6 Picture Bus Chroma3 R1/CR1IN Red1/Cr1 Analog Component Input 43 C5 Picture Bus Chroma4 B2/CB2IN Blue2/Cb2 Analog Component Input 44 C4 Picture Bus Chroma5 G2/Y2IN Green2/Y2 Analog Component Input 45 VSUPC Supply Voltage, Chroma Output Circuitry6 R2/CR2IN Red2/Cr2 Analog Component Input 46 GNDC Ground, Chroma Output Circuitry7 ASGF Analog Shield GNDF 47 C3 Picture Bus Chroma8 FFRSTWIN FIFO Reset Write Input ** 48 C2 Picture Bus Chroma

9 VSUPCAPDigital Decoupling Circuiltry SupplyVoltage 49 C1 Picture Bus Chroma

10 VSUPD Supply Voltage, Digital Circuitry 50 C0 Picture Bus Chroma (LSB)11 GNDD Ground, Digital Circuitry 51 GNDSY Ground, Sync Pad Circuitry12 GNDCAP Digital Decoupling Circuitry GND 52 VSUPSY Supply Voltage, Sync pad Circuitry13 SCL 12C Bus Clock 53 INTLC Interlace Output14 SDA I2C Bus Data 54 AVO Active Video Output15 RESQ Reset Input, Active Low 55 FSY/HC/HSYA Front Sync/ Horizontal Clamp Pulse/

Front-End Horizontal Sync Output16 TEST Test Pin, connect to GNDD 56 MSY/HS Main Sync/Horizontal Sync Pulse17 VGAV VGAV Input 57 VS Vertical Sync Pulse

18 YCOEQ Y/C Output Enable Input, Active Low 58 FPDAT/VSYA Front-End/Back-End Data/Front-EndVertical Sync Output **

19 FFIE FIFO Input Enable 59 VSTBY Standby Supply Voltage20 FFWE FIFO Write Enable 60 CLK5 CCU 5 MHz Clock Output21 FFRSTW FIFO Rest Write/Read 61 NC Not connected22 FFRE FIFO Read Enable 62 XTAL1 Analog Crystal Input23 FFOE FIFO Output Enable 63 XTAL2 Analog Crystal Output24 CLK20 Main Clock Output 20.25MHz 64 ASGF Analog Shield GNDF

25 GNDPA Pad Decoupling Circuitry GND 65 GNDF Ground, Analog Front-End26 VSUPPA Pad Decoupling Circuitry Supply Voltage 66 VRT Reference Voltage Top, Analog

27 LLC2 Double Clock Output 67 I2CSEL I2C Bus Address Select

28 LLC1 Clock Output 68 ISGNDSignal Ground for Analog Input, Connectto GNDF

29 VSUPLLC Supply Voltage, LLC Circuitry 69 VSUPF Supply Voltage, Analog Front-End30 GNDLLC Ground, LLC Circuitry 70 VOUT Analog Video Output31 Y7 Picture Bus Luma (MSB) 71 CIN Chroma/ Analog Video 5 Input32 Y6 Picture Bus Luma 72 VIN1 Video 1 Analog Input33 Y5 Picture Bus Luma 73 VIN2 Video 2 Analog Input34 Y4 Picture Bus Luma 74 VIN3 Video 3 Analog Input35 GNDY Ground, Luma Output Circuitry 75 VIN4 Video 4 Analog Input

36 VSUPY Supply Voltage, Luma Output Circuitry 76 VSUPAI Supply Voltage, Analog Component Inputs

37 Y3 Picture Bus Luma 77 GNDA1Ground, Analog Component Inputs Front-End

38 Y2 Picture Bus Luma 78 VREF Reference Voltage Top, AnalogComponent

39 Y1 Picture Bus Luma 79 FB1IN Fast Blank Input

40 Y0 Picture Bus Luma (LMB) 80 AISGNDSignal Ground for Analog ComponentInputs, connect to GNDAI

IC301

Information of ICs

-28-

Pin No. Pin Name Function Pin No. Pin Name Function1 VIN 4 Feed Back

2 Output 5 ON/OFF

3 Ground

Pin No. Pin Name Function Pin No. Pin Name Function1 Ground 3 VIN

2 VOUT

Pin No. Pin Name Function Pin No. Pin Name Function

1 GND Ground 47 GND Ground

2-9 GREEN[7:0]Outputs of Converter "Green," Bit 7 Is theMSB

48 GAIN Analog Input for Converter G

10 GND Ground 49 SOGIN Input for Sync-on-Green

11 VDD Output Power Supply 50 GND Ground

12-19 Blue[7:0]Output of Converter "Blue," Bit 7 Is theMSB

51-52 VD Analog Power Supply

20-21 GND Ground 53 GND Ground

22-23 VDD Output Power Supply 54 RAIN Analog Input for Converter R

24-25 GND Ground 55 A0 Serial Port Address Input 1

26-27 VD Analog Power Supply 56 SCL Serial Port Data Clock (100KHz Maximum)

28 GND Ground 57 SDA Serial Port Data I/O

29 COAST PLL COAST Signal Input 58 REF BYPASS Internal Reference Bypass

30 HSYNC Horizontal SYNC Input 59 VD Analog Power Supply

31 VSYNC Vertical SYNC Input 60-61 GND Ground

32 GND Ground 62 VD Analog Power Supply

33 FILTConnection for External Filter Componentsfor Internal PLL

63 GND Ground

34-35 PVD PLL Power Supply 64 VSOUTVSYNC Output Clock (Phase-Aligned withDATACK)

36 GND Ground 65 SOGOUT Sync on Green Slicer Output

37 MIDSCV Internal Midscale Voltage Bypass 66 HSOUTHSYNC Output Clock (Phase-Aligned withDATACK)

38 CLAMP Clamp Input (External CLAMP Signal) 67 DATACK Data Output Clock

39 VD Analog Power Supply 68 GND Ground

40-41 GND Ground 69 VDD Output Power Supply

42 VD Analog Power Supply 70-77 Red [7:0] Outputs of Converter "Red," Bit 7 Is the MSB

43 BAIN Analog Input for Converter B 78-79 VDD Output Power Supply

44 GND Ground 80 GND Ground

45-46 VD Analog Power Supply

IC601

IC101

IC102

Information of ICs

-29-

IC701Pin No. Pin Name Function Pin No. Pin Name Function

1 CAP5 Decoupling for ADC Supply RegulatorOutput 21 Avcc Power Supply Pin

2 SIF1 Subcarrier 1 Input 22 CAP7 Decoupling for Digital Regulator Output

3 CAP6 Decoupling for Input Amplifier Reference 23 RESET Power On Reset

4 SIF2 Subcarrier 2 Input 24-31 NC Not Connector5 GND3 Ground for Input Amplifier 32 GND1 Digital Ground6 MOUT Mono Audio Output 32 XOUT Crystal Oscillator Output7 MIN Mono Audio Input 33 XOUT Crystal Oscillator Input8 CAP8 ADC Vtop Decoupling 34 XIN Crystal Oscillator Input9 LIL1 Line 1 Left Input (SCART 1) 35 Not used To be connected to ground

10 LIR1 Line 1 Right Input (SCART 1) 36 SDA I2C Serial Data11 GND4 Audio Ground 37 SCL I2C Serial Clock12 LIL2 Line 2 Left Input (SCART 2) 38 NC Not Connector

13 LIR2 Line 2 Right Input (SCART 2) 39 CAP3 Decoupling for Digital 3V (regulatoroutput)

14 CAP2 Decoupling for Audio Matrix 40 REG Base Drive for External RegulatorTransistor

15 CAP1 Decoupling for Bandgap Reference 41 DVDD5 5V Supply16 AOL1 Line 1 Left Output (SCART 1) 42 GND2 Digital Ground17 AOR1 Line 1 Right Output (SCART 1)18 CAP4 Audio Matrix VDD (5V)19 AOL2 Line 2 Left Output (SCART 2)20 ALR2 Line 2 Right Output (SCART 2)

IC702Pin No. Pin Name Function Pin No. Pin Name Function

1 Ina Ach Input 16 VCC Power Supply Pin2 BBE1a Ach BBE Filter1 (Process) 17 AUX1 Auxiliary Output13 BBE2a Ach BBE Filter2 (Lo Contour) 18 AUX0 Auxiliary Output04 BBE OUTa Ach Output for the Other Accessories 19 CTL DAC Output for Tone Low Frequency5 TONE Ina Ach Input From the Other Accessories 20 CTH DAC Output for Tone High Frequency6 TONE-Ha Ach Treble Filter 21 VREF Reference Voltage7 TONE-La Ach Bass Filter 22 SR-FIL NJRC Original Surround Filter8 OUTa Ach Output 23 OUTb Bch Output9 AGC AGC 24 TONE-Lb Bch Bass Filter

10 SS-FIL Simulated Stereo Filter 25 TONE-HB Bch Treble Filter11 CVB DAC Output for Bch Volume & Balance 26 TONE Inb Bch Input from the Other Accessories12 CVA DAC Output for Ach Volume & Balance 27 BBE OUTb Bch Output for the other Accessories13 SDA SDA Data Input (I2C BUS) 28 BBE 2b Bch BBE Filter2 (process)14 SCL SCL Data Input (I2C BUS) 29 BBE1b Bch BBE Filter1 (Lo Contour)15 GND GND 30 Inb Bch Input

Pin No. Pin Name Function Pin No. Pin Name Function1 N.C. 7 Ch.2 output2 Ch.1 input 8 Mute3 Ripple filter 9 Output GND4 Input GND 10 Vcc5 Ch.2 input 11 Standby6 N.C. 12 Ch.1 output

IC703

Information of ICs

-30-

Information of ICs

IC201Pin No Port Name Function Pin No Port Name Function

1 BUSTYPE Bus type select 111 OSDB OSD BLUE input2 VDDP PAD Power 112 OSDBLNK OSD select.

3-10 PIXINA [7:0]Pixel input A GREEN [7:0} from ADC. Y[7:0]: Color data from VideoDecoder

113 VDD Core Power

11 CLAMP Clamp signal 114 DQM2 Data mask byte enable (For SGRAM)

12-19 PIXINA [15:8]Pixel input A GREEN [7:0} from ADC. CbCr[7:0]: Color data fromVideo Decoder.

115 DQM3 Data mask byte enable (For SGRAM)

20 VDD Core Power 116 GNDP PAD GNDPix input A BLUE[7:0] from ADC. 117-124 MD[31:24] Memory data input/outputD23: MPLLC2, (Video input clk signal)/2. 125 VDDP PAD PowerD22: MPHS, Video input Hsync signal. 126-133 MD[23:0] Memory data input/outputD21: MPVS, Video input Vsync signal. 134 GNDP PAD GNDD20: MPODD, Video input Odd/Even field signal. 135 MCLK Memory clockD19: MPHREF, Video input horizontal reference signal. 136 GND Core GNDD18: MPLLC, Video input clk signal. 137 MA10 Memory addressD17: MPCREF, Video input clk reference signal. 138 VDDP PAD PowerD16: MPVREF, Video input vertical reference signal. 139-148 MA[9:0] Memory address

29 DDE Digital display enable input pin 149 GNDP PAD GND30 GND Core GND 150 CKE Memory clock enable31 GNDP PAD GND 151 WE# Write Enable

32,33 AGND Analog GND 152 CAS# Column address strobe34 X1 Analog pad for Reference Frequency Input for ternal 153 RAS# Row address strobe35 XO Analog pad for rReference Frequency Output for internal oscillator. 154 VDDP PAD Power

36,37 AGND Analog GND 155-156 DQM[0:1] Data mask byte enable (For SGRAM)38 VDDP PAD Power 157 GNDP PAD GND

39-45 BB[7:0} BLUE DATA (Even) 158 GND Core GND46 GNDP PAD GND 159-166 MD[15:8] Memory data input/output47 BB0 BLUE DATA (Even) 167 VDDP PAD Power48 VDDP PAD Power 168 VDD Core Power

49-56 GB[7:0] GREEN DATA (Even) 169 MD7 Memory data input/output57 GNDP PAD GND 170 GNDP PAD GND

58-64 RB[7:0] RED DATA (Even) 171-177 MD[6:0] Memory data input/output65 VDDP PAD Power 178-185 AD[7:0] Multiplexed low_order address and data bus66 RB0 RED DATA (Even) 186 GNDP PAD GND

67 GNDP PAD GND 187 CPUA15/BCShigh_order a15 address input, or BIU Valid cycle.(for ISA bus debug)

68 LCKB Even data clock output for LCD display 188 VDDP PAD Power69 GND Core GND 189 ALE Address Latch Enable for 8051 Bus.70 LCKA Odd data clock output for LCD display 190 WR# Memory Read Strobe71 GNDP PAD GND 191 RD# Memory Read Strobe.

72-79 BA[7:0] BLUE DATA (Odd) 192 TMCLK External MCLK input80-87 GA[7:0] GREEN DATA (Odd) 193 RSTZ# System reset.

88 VDD Core Power General I/O89 VDDP PAD Power GPIO[0]: Hsync source select90 RA 7 RED DATA (Odd) GPIOA[1]: ADC-Coast source select91 GNDP PAD GND GPIO[3]: DS for External ADC

92-98 RA[6:0] RED DATA (Odd) GPIO [4] PDEN for External PLL

99 LHSYNC HSYNC output for LCD display GPIO [5] Input select100 LVSYNC VSYNC output for LCD display 200 IRQ Interrupt request101 LDTG Data Enable output for LCD display 201 SOGCS Input Sync on Green composite Sync

102 OSDB0/GOUT1 Extended OSD RED input or use as Motorola OSD intensity input(Output Share With GOUT4)

202 TDCLK/CSYNC External DCLK input/Composite Sync input

103 GNDP PAD GND 203 HSYNC1 Input HSYNC104 GOUT1 General Output1 204 VSYNC1 Input VSYNC105 VDDP PAD Power 205 GOUT3 General Output 3107 12CDATA 12C DATA Pull up by internal 168K Ohm resistor 206 GND Core GND108 12CCLK 12C CLK. Pull up by internal 168K Ohm resistor 207 DCLKA Input dot clock109 OSDR OSD RED input 208 GNDP PAD GND110 OSDG OSD GREEN input

GPIOA[0:5]

PIXINA[23:16]21-28

194-199

-31-

Information of ICs

IC202, IC203Pin No Port Name Function Pin No Port Name Function

1 VDD Power and ground for the input buffers and the core logic. 25 VDD Power and ground for the input buffers and the core logic.2-3 DQ [0:1] Data inputs/outputs are multiplexed on the same pins. 26 VSS Power and ground for the input buffers and the core logic.

4 VSSQIsolated power supply and ground for the output buffers toprovide improved noise immunity.

27-32 A [4:9]Row/column addresses are multiplexed on the same pins.Row address: RA0~RA10, column address:CA0~CA7.

5-6 DQ [2:3] Data inputs/outputs are multiplexed on the same pins. 33 N.CThis pin is recommended to be left No Connection on thedevice.

7 VDDQIsolated power supply and ground for the output buffers toprovide improved noise immunity.

34 CKE

Masks system clock to freeze from the next clock cycle.CKE should be enabled at least one cycle prior to newcommand.Disable input buffers for power down in standby.

8-9 DQ [4:5] Data inputs/outputs are multiplexed on the same pins. 35 CLK Active on the positive going edge to sample all inputs.


36 UDQMMakes data output Hi-Z, tshz after the clock and masksthe output. Blocksdata input when L(U)DQM active.

11-12 DQ [6:7] Data inputs/outputs are multiplexed on the same pins. 37 N.C/RFUThis pin is recommended to be left No Connection on thedevice.



14 LDQMMakes data output Hi-Z, tshz after the clock and masks theoutput. Blocks datainput when L(U)DQM active.

39-40 DQ [8:9] Data inputs/outputs are multiplexed on the same pins.

15 WEEnables write operation and row precharge. Latches data instarting from CAS, WE active.


16 CASLatches column addresses on the positive going edge of theCLK with CAS low. Enables column access.


17 RASLatches row addresses on the positive going edge of the CLKwith RAS low. Enables row access & precharge.


18 CSDisables or enables device operation by masking or enablingall inputs except CLK, CKE and L(U)DQM


19 BASelects bank to be activated during row address latch time.Selects bank for read/write during column address latch time.


20 A10/AP 48-49 DQ [14:15] Data inputs/outputs are multiplexed on the same pins.

21-24 A [0:3] 50 VSS Power and ground for the input buffers and the core logic.

Q707, Q101, Q102Pin No Port Name Function Pin No Port Name Function

1-3 S Source 5-8 D Drain4 G Gate

IC501Pin No. Port Name Function Pin No. Port Name Function

1 N.C. No Connect 22 VSS Ground2-9 P1.0~1.7] Input low order address bits 23 N.C. No Connect10 RST Reset 24-29 P2.0~2.5 Input high order address bits11 P3.0 Flash Mode Selection 30 P2.6 Data Input/Output12 N.C. No Connect 31 P2.7 Output Enable Input13 P3.1 Flash Mode Selection 32 PSEN Program Store Enable14 P3.2 Data Input/Output 33 ALE Write Enable Input15 P3.3 Chip Enable Input 34 N.C. No Connect

16-17 P3.4~3.5] Input high order address bits 35 EA Program Supply Voltage, 12.5~13Volts18 P3.6 Data Input/Output 36-43 P0.7~0.0 Data Input/Output19 P3.7 Flash Mode Selection 44 vcc Power pin

20-21 XTAL [2:1] OSCILLATOR


1-3 N.C. No Connect 6 SCL Clock input4 VSS Ground 7 WP Write Protect5 SDA Data I/O 8 VCC Power pin

IC103, IC104Pin No. Port Name Function Pin No. Port Name Function

1 ADJ (GND) Ground 3 VIN Voltage IN2 VOUT (TAB) Voltage out

Row/column addresses are multiplexed on the same pins.Row address: RA0~RA10, column address:CA0~CA7.

-32-


1 I0 Inputs 8 O3 Outputs2 O0 Outputs 9 I3 Inputs3 I1 Inputs 10 O4 Outputs4 O1 Outputs 11 I4 Inputs5 I2 Inputs 12 O5 Outputs6 O2 Outputs 13 I5 Inputs7 GND Ground 14 VCC Power supply

-33-

Information of ICs

Pin No. Pin Name Function Pin No. Pin Name Function

1 P2.0/PWM output for 14-bit high precision Pulse WidthModulator (PWM) 28 TEST not available; connect this pin to VSSA

2 P2.1/PWM0 ouputs for 6-bit PWMs 0 to 6 29 COR3 P2.2/PWM1 output for 6-bit PWMs 0 to 6 30 P3.4/PWM7 described above4 P2.3/PWM2 output for 6-bit PWMs 0 to 6 31 VDDA analog supply voltage (3.3V)5 P2.4/PWM3 output for 6-bit PWMs 0 to 6 32 B Blue colour information pixel rate output6 P2.5/PWM4 output for 6-bit PWMs 0 to 6 33 G Green colour information pixel rate output7 P2.6/PWM5 output for 6-bit PWMs 0 to 6 34 R Red colour information pixel rate output

8 P2.7/PWM6 output for 6-bit PWMs 0 to 6 35 VDS video/data switch push-pull output for pixelrate fast blanking

9 P3.0/ADC0 inputs for the software Analog-to-Digital-Converter(ADC) facility 36 HSYNC horizontal sync pulse input

10 P3.1/ADC1 inputs for the software Analog-to-Digital-Converter(ADC) facility 37 VSYNC vertical sync pulse input

11 P3.2/ADC2 inputs for the software Analog-to-Digital-Converter(ADC) facility 38 VSSP periphery ground

12 P3.3/ADC3 inputs for the software Analog-to-Digital-Converter(ADC) facility 39 VDDC core supply voltage (+3.3V)

13 Vssc core ground 40 OSCGND crystal oscillator ground14 SCL(NVRAM) I2C-bus Serial Clock input to Non-Volatile RAM 41 XTALIN 12 MHz crystal oscillator input

15 SDA(NVRAM) I2C-bus Serial Data input/output (Non-VolatieRAM)

42 XTALOUT 12 MHz crystal oscillator ouput

16 P0.2 input/output for general use 43 RESET reset input17 P0.3 input/output for general use 44 VDDP periphery supply voltage (+3.3V)18 P0.4 input/output for general use 45 P1.0 input/output for general use

19 P0.5 8 mA current sinking capability for direct drive ofLight Emitting Diodes (LEDs) 46 P1.1 input/output for general use

20 P0.6 8 mA current sinking capability for direct drive ofLight Emitting Diodes (LEDs) 47 P1.2 input/output for general use

21 P0.7 input/output for general use 48 P1.3 input/output for general use22 VSSA analog ground 49 SCL I2C-bus Serial Clock input from application

23 CVBS0Composite Video Baseband Signal (CVBS) input;a positive-going 1 V (peak-to-peak) input isrequired; connected via a 100 nF capacitor

50 SDA I2C-bus Serial Data input/output (application)

24 CVBS1Composite Video Baseband Signal (CVBS) input;a positive-going 1 V (peak-to-peak) input isrequired; connected via a 100 nF capacitor

49 SCL I2C-bus Serial Clock input from application

25 SYNC_FILTERsync-pulse-filter input for CVBS; this pin shouldbe connected to VSSA via a 100 nF capacitor 50 SDA I2C-bus Serial Data input/output (application)

26 IREFreference current input for analog circuits; forcorrect operation a 24 kO resistor should beconnected to VSSA

51 P1.4 input/output for general use

27 FRAMEFrame de-interlace output synchronized with theVSYNC pulse to produce a non-interlaced displayby adjustment of the vertical deflection circuits

52 P1.5 input/output for general use

IC601A

Item Part No. Description Location1 E1111-005024-1 COIL FIX CHIP CMI3216VBP 5R6K 1206 L705 L710 L711 L712 L713

2 E1111-006027-1 COIL FIX CHIP CMI3216VBP 100M 1206 L709

3 E1111-016001-2 FB FIX CHIP CBY321611UTP 190 1206 L706 L707 L708 L714 L715

4 E1301-009001-1 CAP EC V CD11X-BP T05 221M 25DC 8×9 C790

5 E1301-009002-1 CAP EC V CD11X-BP T05 471M 25DC 10×13 C791 C792 C770 C771

6 E1301-012001-1 CAP EC V CD11-BP T05 100M 16DC 5×11 C706 C722 C731 C735 C736 C739C740 C773 C774 C7797 E1301-012004-1 CAP EC V CD11-BP T05 470M 16DC 5×11 C702 C760 C781 C793 C795

8 E1301-012005-1 CAP EC V CD11-BP T05 101M 16DC 6×11 C737 C724

9 E1301-013006-1 CAP EC V CD11-BP T05 101M 25DC 6×12 C732

10 E1301-012009-1 CAP EC V CD11-BP T05 102M 16DC 10×18 C775 C77711 E1301-015005-1 CAP EC V CD11-BP T05 1R0M 50DC 5×11 C709 C710 C711 C712 C76912 E1301-015008-1 CAP EC V CD11-BP T05 4R7M 50DC 5×11 C753 C754 C755 C756 C757 C765

C766 C794 C784 C78613 E1302-003006-1 CAP EC NP V CD71-BP T05 1R0M 50DC 5×11 C75214 E1302-003010-1 CAP EC NP V CD71-BP T05 4R7M 50DC 5×11 C741 C74215 E1321-002011-1 CAP MY V PL.PN-BP T05 682K 50DC C762 C763

16 E1326-001011-2 CAP CHIP CC41-CGNT NPO T06 100J 50DC 0603 C72117 E1326-001016-2 CAP CHIP CC41-CGNT NPO T06 220J 50DC 0603 C727 C728 C76818 E1326-001027-2 CAP CHIP CC41-CGNT NPO T06 101J 50DC 0603 C708 C729 C730 C758 C759

19 E1326-001032-2 CAP CER CHIP CC41-CGNT T06 NPO 221J 50DC 0603 C717 C718 C719 C720

20 E1326-001041-2 CAP CER CHIP CC41-CGNT T06 NPO 102J 50DC 0603 C713 C714 C715 C716 C723 C767

21 E1326-003023-2 CAP CER CHIP CC41-BNT X7R T06 332K 50DC 0603 C743 C744

22 E1326-003029-2 CAP CER CHIP CC41-BNT X7R T06 103K 50DC 0603 C703 C704 C705 C707 C733

23 E1326-004025-2 CAP CER CHIP CC41-BNT X7R T06 472M 50DC 0603 C747 C748

24 E1326-005018-2 CAP CER CHIP CC41-FNT T06 333M 50DC 0603 C745 C746

25 E1326-005029-2 CAP CER CHIP CC41-FNT T06 224M 50DC 0603 C700

26 E1326-006024-2 CAP CER CHIP CC41-FNT T06 104Z 50DC 0603 C701 C725 C726 C738 C749 C750C751 C761 C772

27 E1503-311088-1 RES MOF H 1W 330J T52 R750

28 E1503-322129-1 RES MOF H 2W 5R6J T52 R781

29 E1505-011004-2 RES CHIP RC-03KTP T06 1/16W 101J 0603 R710 R711 R732 R733

30 E1505-011157-2 RES CHIP RC-03KTP T06 1/16W 561J 0603 R766 R768


32 E1505-011007-2 RES CHIP RC-03KTP T06 1/16W 104J 0603 R702 R703 R704 R705 R713 R727R728

33 E1505-011008-2 RES CHIP RC-03KTP T06 1/16W 105J 0603 R712


35 E1505-011076-2 RES CHIP RC-03KTP T06 1/16W 221J 0603R706 R707 R718 R723 R725 R726R730 R731 R771




39 E1505-011110-2 RES CHIP RC-03KTP T06 1/16W 332J 0603 R765 RR767

40 E1505-011111-2 RES CHIP RC-03KTP T06 1/16W 333J 0603 R715 R791 R720

41 E1505-011124-2 RES CHIP RC-03KTP T06 1/16W 390J 0603 R70842 E1505-011141-2 RES CHIP RC-03KTP T06 1/16W 471J 0603 R790

43 E1505-031202-2 RES CHIP RC-06K000OT T12 1/8W 000O 1206 R780

44 E1507-321098-1 RES FR H 1W T52 R47J R776

45 E2111-001001-2 TR PNP CHIP HMBT1015 A4Y SOT-23 TP Q706

46 E2112-001002-2 TR NPN CHIP HMBT1815 C4G SOT-23 TP Q701 Q702 Q703 Q704 Q705

47 E2115-001005-1 TR SINGLE P-CHANNEL MOSFET SO-8 Q707

48 E2301-001061-0 IC 5+5W AUDIO AMPLIFIER HSIP012-0000A IC703

49 E2301-001062-0 IC MULTISTANDARD TV SOUND DEMODULATOR SDIP42 IC701

50 E2351-001028-0 IC REGULATOR 3PIN SMD IC707

AUDIO PCB ASSEMBLY

PCB Component List

-34-

Item Part No. Description Location

51 E2351-001029-0 IC REGULATOR 3PIN SMD IC706

52 E2351-001068-0 IC AUDIO PROCESSOR with SOUND ENHANCEMENT SDMP30 IC702

53 E2503-001014-0 DIODE ZENER CHIP TZMB8V2-GS08 8V2 SOD-80 ZD701

54 E3101-001003-1 PLUG PH-4A PIN HEADER (180°) 2.0mm 4P CN703

55 E3101-001006-2 PLUG PH-7AW PIN HEADER (90°) 2.0mm 7P CN704


57 E3101-106005-2 SOCKET PIN HEADER (90°) 2.54mm 2×6P/W CN702

58 E3702-002025-2 PCB FOR AUDIO 120mm×90mm

59 E4301-001025-0 OSCILLATOR X' TAL HC-49/US 27.000000MHz X701

60 M4601-015111000 MEAT SINK ALUMINUM 16.2x15.5H

61 M8004-260802312 SELF-TAPING SCREW WITH BINDING HEAD BST2.6x8B-HCr IC703/HEAD SINK

PCB Component List

-35-


1 E1102-001009-1 COIL FIX R TC3026-1R0M 1R0M 3A L101

2 E1111-016001-2 FB FIX CHIP CBY321611UTP 190 1206

L104 L105 L201 L202 L300 L301 L304L401 L402 L403 L404 L405 L406 L407L408 L409 L601 L602 L603 L604 L605L606 L607

3 E1112-001001-0 COIL FIX SFRH127-470M-R 47uH 3.5A L1024 E1301-009001-1 CAP EC V CD11X-BP T05 221M 25DC 8x9 C101 C103 C1365 E1301-009002-1 CAP EC V CD11X-BP T05 471M 25DC 10× 13 C104 C105

6 E1302-020001-1 CAP EC CHIP 100M 16DC C117 C314 C325 C505 C627 C628 C641

7 E1302-020003-1 CAP EC CHIP 220M 16DC C506

8 E1302-020004-1 CAP EC CHIP 470M 16DC C107 C111 C113 C116 C644

9 E1308-001003-1 CAP TT CHIP CA45-TP 100K 16DC 1310 C315 C320 C330

10 E1308-001010-1 CAP TT CHIP CA45-16V22uF 22uF 16DC 1310 C433

11 E1326-001011-2 CAP CHIP CC41-CGNT NPO T06 100J 50DC 0603

C238 C239 C240 C241 C242 C243 C244C245 C246 C247 C248 C249 C250 C251C252 C253 C254 C255 C256 C257 C258C259 C260 C261 C262 C263 C264 C265C266 C267 C268 C269 C270 C271 C272C273 C274 C275 C276 C277 C278 C279C280 C281 C282 C283 C284 C285 C410C412 C414 C415 C420 C421 C430 C431

12 E1326-001013-2 CAP CER CHIP CC41-CGNT T06 NPO 150J 50DC 0603 C234 C235 C236 C237 C620

13 E1326-001016-2 CAP CER CHIP CC41-CGNT T06 NPO 220J 50DC 0603 C201 C202 C311 C312 C502 C503

14 E1326-001022-2 CAP CER CHIP CC41-CGNT T06 NPO 470J 50DC 0603 C212 C601 C602 C603 C607 C608 C609

15 E1326-001027-2 CAP CER CHIP CC41-CGNT T06 NPO 101J 50DC 0603

C229 C230 C288 C289 C304 C305 C401C402 C404 C405 C407 C408 C417 C418C422 C423 C615 C616 C645 C646

16 E1326-001036-2 CAP CHIP CC41-CGNT NPO T06 391J 50DC 0603 C303 C317 C32317 E1326-003024-2 CAP CER CHIP CC41-BNT X7R T06 392K 50DC 0603 C61318 E1326-003029-2 CAP CER CHIP CC41-BNT T06 103K 50DC 0603 C313 C406

19 E1326-005019-2 CAP CER CHIP CC41-FNT T06 393M 50DC 0603 C61420 E1326-005020-2 CAP CER CHIP CC41-FNT T06 473M 50DC 0603 C307 C316 C33121 E1326-005029-2 CAP CER CHIP CC41-FNT T06 224M 50DC 0603 C301 C319 C321 C411 C413 C416

22 E1326-006024-2 CAP CER CHIP CC41-FNT T06 104Z 50DC 0603

C102 C106 C110 C112 C115 C118 C203C204 C205 C206 C207 C208 C209 C210C211 C213 C214 C215 C216 C217 C218C219 C220 C221 C222 C223 C224 C225C226 C227 C228 C232 C308 C309 C310C324 C501 C604 C605 C606 C610 C612C621 C622 C623 C624 C629 C630 C631C632 C633 C634 C635 C636 C638 C639C640 C642 C643 C648 C637 R625 R626

23 E1326-065055-2 CAP CHIP CT41-0805F684M500NT 684M 50DC 0805 C403 C409 C419 C42424 E1326-303017-2 CAP CER CHIP CT41-BNT X7R T06 152K 50DC 0603 C302 C306 C318 C322

25 E1505-011004-2 RES CHIP RC-03KTP T06 1/16W 101J 0603R301 R302 R506 R507 R607R608 R617 R618


27 E1505-011006-2 RES CHIP RC-03KTP T06 1/16W 103J 0603 R111 R306 R419 R420 R502 R505

28 E1505-011008-2 RES CHIP RC-03KTP T06 1/16W 105J 0603 R202 R307 R501


30 E1505-011075-2 RES CHIP RC-03KTP T06 1/16W 220J 0603R201 R320 R321 R323 R324 R325 R326R604 R610 R611

DRIVE PCB ASSEMBLY

PCB Component List

-36-



32 E1505-011092-2 RES CHIP RC-03KTP T06 1/16W 270J 0603R401 R403 R405 R408 R410 R412 R414R415 R417

33 E1505-011110-2 RES CHIP RC-03KTP T06 1/16W 332J 0603 R60634 E1505-011111-2 RES CHIP RC-03KTP T06 1/16W 333J 0603 R10335 E1505-011141-2 RES CHIP RC-03KTP T06 1/16W 471J 0603 R102 R10436 E1505-011142-2 RES CHIP RC-03KTP T06 1/16W 472J 0603 R503 R504 R511 R615 R616


38 E1505-011180-2 RES CHIP RC-03KTP T06 1/16W 750J 0603R402 R404 R406 R407 R409 R411 R413R416 R418 R428 R601 R602 R603

39 E1505-011202-2 RES CHIP RC-03KTP T06 1/16W 000 0603 R304 R605 Q403CE Q404CE Q405CE

40 E1505-031202-2 RES CHIP RC-06K000OT T12 1/8W 000O 1206 R207

41 E1510-001004-2 RES CHIP TFN RCML08WTP 1/16W 101J 0603x4 RP601 RP602 RP603 RP604 RP605 RP606

42 E1510-001066-2 RES CHIP TFN RCML08WTP 1/16W 220J 0603× 4 RP201 RP202

43 E1510-001108-2 RES CHIP TFN RCML08WTP 1/16W 330J 0603× 4

RP203 RP204 RP205 RP206 RP207 RP208RP209 RP210 RP211 RP212 RP213 RP214RP215 RP301 RP302 RP303 RP304

44 E2111-001001-2 TR PNP CHIP HMBT1015 A4Y SOT-23 TP Q501

45 E2112-001002-2 TR NPN CHIP HMBT1815 C4G SOT-23 TP Q103 Q104 Q105 Q40146 E2115-001005-1 TR SINGLE P-CHANNEL MOSFET SO-8 Q101 Q102

47 E2351-001018-0 IC HEX INVERTER SOIC14 IC603

48 E2351-001021-0 IC QFP208 IC201

49 E2351-001032-0 IC 16K-BIT SERIAL EEPROM SOP-8L IC502

50 E2351-001046-0 IC VOLTAGE DETECTOR SOT-89 IC50351 E2351-001048-0 IC DUAL-MODE I2C SERIAL EEPROM SOIC IC60252 E2351-001049-0 IC 5A ADJUSTABLE REGULATOR TO-263 IC103 IC104

53 E2351-001065-0 IC VIDEO DECODER PQFP-80 IC30154 E2351-001077-0 IC 3A STEP-DOWN VOLTAGE REGULATOR TO-263 IC10155 E2351-001082-0 IC 110MSPS ANALOG FLAT PANEL INTERFACE ST-80 IC60156 E2354-001010-0 IC 512K× 16BIT× 2BANKS SRAM TSOP50 IC202 IC203

57 E2391-001013-0 IC SINGLE-CHIP 8-BIT MICROCONTROLLER PLCC44 IC50158 E2502-001005-0 DIODE CHIP LL4148 D501 D604 D605 D606 D60759 E2502-001008-0 DIODE CHIP PM5822 SK34 D10160 E2503-001009-0 DIODE ZENER CHIP TZMB5V1-GS08 5V1 SOD-80 ZD401

61 E2505-001001-0 DIODE BAV99 KJE SOT-23 D601 D602 D603





66 E3101-011005-1 SOCKET FEMALE HEADER (90°) 2.54mm 2× 6P CN403

67 E3102-004012-1 SOCKET DF14A-25P-1.25H FFC CONNECTOR (90°) 1.25mm 25P CN2

68 E3102-004013-1 SOCKET DF14A-30P-1.25H FFC CONNECTOR (90°) 1.25mm 30P CN1

69 E3103-001004-1 IC SOCKET PLCC44 1.27mm 44P IC50170 E3421-001062-0 WIRE ASSY SAN-9Y/PH-9Y UL2468#26 L=180mm 2.0mm 9P CN40471 E3703-001004-2 PCB FOR DRIVE 154mm× 130mm72 E4301-001016-0 OSCILLATOR X' TAL HC-49/US 11.0592MHz X50173 E4301-001017-0 OSCILLATOR X' TAL HC-49/US 14.318MHz X201


75 E5301-002008-0 FUSE FAST ACTING 20N 4A 125V F101

PCB Component List

-37-


1 E0002-001005-0 BATTERY R03P MERCURY-FREE

2 E3203-001001-1 ANTENNA CONNECTER F-9.5

3 E3405-001009-0 AC CORD CHINA 3PIN 2000mm

5 E3421-001064-0 WIRE ASSY PH-13Y/PH-13Y UL2468#26 L=100mm 2.0mm 13P From CN808 To CN601

6 E3421-001065-0 WIRE ASSY PH-7Y/PH-7Y UL2468#26 L=100mm 2.0mm 7P From CN704 To INVERTER

7 E3421-002102-1 WIRE ASSY PH-4P/PH-4P UL2468#28 L=50mm 2.0/2.0mm 4P From CN807 To CN703



10 E3421-002113-1 WIRE ASSY PH2.0-6P/PH2.0-6P L=50mm 2.0/2.0mm 6P From CN801 To CN401

11 E3421-006006-0 WIRE ASSY SP021018393 L=200mm 60P/25P/30P From CN1, CN2 To Panel

13 E3422-005001-0 WIRE VGA 1.8M BEIGE CORE 15PIN L=1850mm

14 E3422-006001-0 WIRE STEREO CONNECTOR F =3.5mm L=600mm

15 E5501-001002-0 ADAPTER 12VDC 4A

16 E5501-002003-0 DC/AC INVERTER FOR CHIMEI 15" TFT-LCD

17 E5501-003005-0 REMOTE CONTROL TRANSMITTER WITH UPSIDE

18 E5601-001012-0 SPEAKER VCP3048N-8-ECJ 8OHM 2W 30×48mm

19 E6101-001003-0 TFT-LCD CHI MEI

ELECTRONIC COMMON PART ASSEMBLY

PCB Component List

-38-

Item Part Number Description Location

1 E1101-021025-2 COIL FIX H AL0410ST T52 220K L101

2 E1301-011005-1 CAP EC V CD11-BP T05 221M 10DC 6x12 C101

3 E1311-001028-2 CAP CER V NP0 101J 50DC C102,C103

4 E1501-201004-2 RES CBF H T52 1/8W 101J R101, R102


6 E3409-001002-0 WIRE JUMPER 5.00mm 0.6mm 1KG=399M JP101

7 E3701-001020-2C PCB FOR TUNER 110mm×53mm

8 E5401-001004-0 TUNER TCPQ9091PD27D PAL B/G/E/D/K SECAM L/L' TUNER




3 E3101-001005-1 PLUG PH-6A PIN HEADER(1800) 2.0mm 6P CN801



6 E3201-001032-1 JACK PIN AV2-8.3-11 WHITE RED 2P J805

7 E3201-001035-1 JACK PIN AV1-8.3-19Y YELLOW 1P J802

8 E3201-001051-1 SOCKET PIN VGA WS2108102456 15P J804

9 E3201-001071-1 JACK PIN S-VIDEO SK-17-04 5P J803

10 E3202-001004-1 JACK PHONE CK3-3.5-5B J807 J808

11 E3202-001009-1 JACK POWER DC-06A J801

12 E3202-001025-1 JACK PHONE CK3-3.5-7C J806

13 E3409-001000-0 WIRE JUMPER 0.6mm 1KG=399MJMP1 JMP2 JMP3 JMP4 JMP5 JMP6

JMP7 JMP8 JMP9 JMP10 JMP11JMP12 JMP13

14 E3422-006004-0 WIRE ASSY SCART/12P/6P L=150mm15 E3701-001072-2 PCB FOR INPUT/OUTPUT 208mm×34mm


1 E1301-012004-1 CAP EC T05 470M 16DC 5x11 C501

2 E1501-001006-1 RES CBF H RD16-STP T52 1/6W 103J R502, R503, R504, R505

3 E1501-001007-1 RES CBF H RD16-STP T52 1/6W 104J R506

4 E1501-001140-2 RES CBF H T52 1/6W 470J R508

5 E1501-001173-1 RES CBF H RD16-STP T52 1/6W 681J R507

6 E2102-001001-1 TR NPN 3DG1815(2SC1815) Y TO-92 Q501

7 E2501-001001-1 DIODE SILICON H 1N4148 T52 DO-35 BPD501, D502, D503, D504, D505, D506,D507

8 E2509-001002-1 DIODE LED V 3G2PD GREEN LD501

9 E2701-001002-0 IR DETECTOR FM-6308LM IR501



12 E3409-001004-0 WIRE JUMPER 7.50mm 0.6mm 1KG=399M JP501, JP502, JP503

13 E3409-001005-0 WIRE JUMPER 10.0mm 0.6mm 1KG=399M JP504

CONTROL KEY PCB ASSEMBLY

TUNING PCB ASSEMBLY

INPUT PCB ASSEMBLY

PCB Component List

-39-

14 E3421-001017-1 WIRE ASSY PH-5Y/JC20-5Y UL=2468#26 L=100mm 2.0mm 5P CN502 TO CN503

15 E3421-001021-0 WIRE ASSY PH/PH-8Y UL2468#26 L=320mm 2.0/2.0mm 8P From CN501 To CN5010A

16 E3421-004005-0 WIRE 1PIN UL1007#20 L=40mm JP505 JP506

17 E3701-001020-1A PCB CONTROL KEY 161mm×25mm

18 E3701-001020-1B PCB POWER KEY 84mm×25mm

19 E4102-001001-0 SWITCH TACT KFC-A06-02 6×6×5S501, S502, S503, S504, S505, S506,S507

20 M6901-070704121 SPONGE PAD CORD POWER PCB

PCB Component List

-40-


1 E3202-001004-1 JACK PHONE CK3-3.5-5B J701

2 E3421-002061-0 WIRE ASSY SCN/SCN-2Y UL2468#22 RED/BLACK L=100mm 2.5mm 2P CN701, CN702

3 E3701-001020-1D PCB FOR SPEAKER OUT 30mm×12mm

SPEAKER OUT PCB ASSEMBLY

TELETEXT PCB ASSEMBLY


1 E1111-016001-2 FB FIX CHIP CBY321611UTP 190 1206 L601 L602 L603

2 E1302-020002-1 CAP EC CHIP 2R2M 16DC C607

3 E1302-020005-1 CAP EC CHIP 101M 16DC C601

4 E1326-001016-2 CAP CER CHIP CC41-CGNT T06 NPO 220J 50DC 0603 C608, C609

5 E1326-006024-2 CAP CER CHIP CC41-FNT T06 104Z 50DC 0603 C602, C603, C604, C611, C612, C613

6 E1505-011004-2 RES CHIP RC-03KTP T06 1/16W 101J 0603 R639, R640



9 E1505-011142-2 RES CHIP RC-03KTP T06 1/16W 472J 0603 R617 R618 R628 R641 R642

10 E1505-011202-2 RES CHIP RC-03KTP T06 1/16W 000 0603 R651 R652

11 E1510-001005-2 RES CHIP TFN RCML08WTP 1/16W 102J 0603× 4 RP606

12 E1510-001142-2 RES CHIP TFN RCML08WTP 1/16W 472J 0603× 4 RP601 RP602 RP603 RP604 RP605

13 E2301-001063-0 IC TELETEXT DECODERS SDIP-52 IC601

14 E2502-001005-0 DIODE CHIP LL4148 D601 D602 D603 D604

15 E3101-015001-1 SOCKET PIN HEADER (180°) 2.0mm 2× 6P/W CN602

16 E3101-015002-1 SOCKET PIN HEADER (180°) 2.0mm 2× 9P/W CN601

17 E3702-002023-0 PCB FOR TELETEXT 66mm× 38mm


15 tft-lcd tv/monitor model: tlm1510eudiagramas.diagramasde.com/otros/tlm-1510eu.pdf · 2013. 3....

Documents