14777: liberty ii lc lightbar - whelen engineering company
TRANSCRIPT
Page 1
©2014 Whelen Engineering Company Inc.Form No.14777C (121219)
Au
tom
oti
ve:
Lig
htb
ars
For warranty information regarding this product, visit www.whelen.com/warranty
• Proper installation of this product requires the installer to have a good understanding of automotive electronics, systems and procedures.• Whelen Engineering requires the use of waterproof butt splices and/or connectors if that connector could be exposed to moisture.• Any holes, either created or utilized by this product, should be made both air- and watertight using a sealant recommended by your vehicle
manufacturer.• Failure to use specified installation parts and/or hardware will void the product warranty.• If mounting this product requires drilling holes, the installer MUST be sure that no vehicle components or other vital parts could be damaged
by the drilling process. Check both sides of the mounting surface before drilling begins. Also de-burr the holes and remove any metal shards or remnants. Install grommets into all wire passage holes.
• If this manual states that this product may be mounted with suction cups, magnets, tape or Velcro®, clean the mounting surface with a 50/50 mix of isopropyl alcohol and water and dry thoroughly.
• Do not install this product or route any wires in the deployment area of your air bag. Equipment mounted or located in the air bag deployment area will damage or reduce the effectiveness of the air bag, or become a projectile that could cause serious personal injury or death. Refer to your vehicle owner’s manual for the air bag deployment area. The User/Installer assumes full responsibility to determine proper mounting location, based on providing ultimate safety to all passengers inside the vehicle.
• For this product to operate at optimum efficiency, a good electrical connection to chassis ground must be made. The recommended procedure requires the product ground wire to be connected directly to the NEGATIVE (-) battery post (this does not include products that use cigar power cords).
• If this product uses a remote device for activation or control, make sure that this device is located in an area that allows both the vehicle and the device to be operated safely in any driving condition.
• Do not attempt to activate or control this device in a hazardous driving situation.• This product contains either strobe light(s), halogen light(s), high-intensity LEDs or a combination of these lights. Do not stare directly into
these lights. Momentary blindness and/or eye damage could result.• Use only soap and water to clean the outer lens. Use of other chemicals could result in premature lens cracking (crazing) and discoloration.
Lenses in this condition have significantly reduced effectiveness and should be replaced immediately. Inspect and operate this product regularly to confirm its proper operation and mounting condition. Do not use a pressure washer to clean this product.
• It is recommended that these instructions be stored in a safe place and referred to when performing maintenance and/or reinstallation of this product.
• FAILURE TO FOLLOW THESE SAFETY PRECAUTIONS AND INSTRUCTIONS COULD RESULT IN DAMAGE TO THE PRODUCT OR VEHICLE AND/OR SERIOUS INJURY TO YOU AND YOUR PASSENGERS!
Warnings to InstallersWhelen’s emergency vehicle warning devices must be properly mounted and wired in order to be effective and safe. Read and follow all of Whelen’s writteninstructions when installing or using this device. Emergency vehicles are often operated under high speed stressful conditions which must be accounted forwhen installing all emergency warning devices. Controls should be placed within convenient reach of the operator so that they can operate the system withouttaking their eyes off the roadway. Emergency warning devices can require high electrical voltages and/or currents. Properly protect and use caution aroundlive electrical connections.Grounding or shorting of electrical connections can cause high current arcing, which can cause personal injury and/or vehicledamage, including fire. Many electronic devices used in emergency vehicles can create or be affected by electromagnetic interference. Therefore, afterinstallation of any electronic device it is necessary to test all electronic equipment simultaneously to insure that they operate free of interference from othercomponents within the vehicle. Never power emergency warning equipment from the same circuit or share the same grounding circuit with radiocommunication equipment. All devices should be mounted in accordance with the manufacturer’s instructions and securely fastened to vehicle elements ofsufficient strength to withstand the forces applied to the device. Driver and/or passenger air bags (SRS) will affect the way equipment should be mounted. Thisdevice should be mounted by permanent installation and within the zones specified by the vehicle manufacturer, if any. Any device mounted in the deploymentarea of an air bag will damage or reduce the effectiveness of the air bag and may damage or dislodge the device. Installer must be sure that this device, itsmounting hardware and electrical supply wiring does not interfere with the air bag or the SRS wiring or sensors. Mounting the unit inside the vehicle by amethod other than permanent installation is not recommended as unit may become dislodged during swerving; sudden braking or collision. Failure to followinstructions can result in personal injury. Whelen assumes no liability for any loss resulting from the use of this warning device. PROPER INSTALLATIONCOMBINED WITH OPERATOR TRAINING IN THE PROPER USE OF EMERGENCY WARNING DEVICES IS ESSENTIAL TO INSURE THE SAFETY OFEMERGENCY PERSONNEL AND THE PUBLIC.
Warnings to UsersWhelen’s emergency vehicle warning devices are intended to alert other operators and pedestrians to the presence and operation of emergency vehicles andpersonnel. However, the use of this or any other Whelen emergency warning device does not guarantee that you will have the right-of-way or that otherdrivers and pedestrians will properly heed an emergency warning signal. Never assume you have the right-of-way. It is your responsibility to proceed safelybefore entering an intersection, driving against traffic, responding at a high rate of speed, or walking on or around traffic lanes. Emergency vehicle warningdevices should be tested on a daily basis to ensure that they operate properly. When in actual use, the operator must ensure that both visual and audiblewarnings are not blocked by vehicle components (i.e.: open trunks or compartment doors), people, vehicles, or other obstructions. It is the user’s responsibilityto understand and obey all laws regarding emergency warning devices. The user should be familiar with all applicable laws and regulations prior to the use ofany emergency vehicle warning device. Whelen’s audible warning devices are designed to project sound in a forward direction away from the vehicleoccupants. However, because sustained periodic exposure to loud sounds can cause hearing loss, all audible warning devices should be installed andoperated in accordance with the standards established by the National Fire Protection Association.
Safety FirstThis document provides all the necessary information to allow your Whelen product to be properly and safely installed. Before beginning the installation and/oroperation of your new product, the installation technician and operator must read this manual completely. Important information is contained herein that couldprevent serious injury or damage.
WARNING: This product can expose you to chemicals including Methylene Chloride which is known to the State of California to cause cancer, andBisphenol A, which is known to the State of California to cause birth defects or other reproductive harm. For more information go towww.P65Warnings.ca.gov.
Installation Guide:Liberty™ II LC Lightbar
51 Winthrop RoadChester, Connecticut 06412-0684Phone: (860) 526-9504Internet: www.whelen.comSales e-mail: [email protected] Service e-mail: [email protected]
®
ENGINEERING COMPANY INC.
Page 2
IMPORTANT! The lightbar should be a minimum of 16" from anyradio antennas.
Mounting your Lightbar:
Refer to the mounting guide included with your mounting foot kit.
Routing your Lightbar Cables:
1. To protect the headliner from damage caused by drilling the cableaccess hole through the vehicle roof, allow a 5” to 7” distancebetween roof and headliner by lowering the headliner beforedrilling.
2. Using a 1” hole saw, drill the cable access hole.
WARNING!There may be a roof support member that spans thedistance between the driver’s and passenger’s side. DO NOTDRILL THROUGH THIS MEMBER! Adjust the location until thehole can be drilled without contacting this support member.
3. Use a round file tosmooth and de-burr theedges of the hole.
4. Insert a 1” grommet(user supplied) into thecable access hole.
5. Insert the cablesthrough the cableaccess hole into thevehicle. Use RTVsilicone to weatherproofthe access hole after the cables are pulled completely into thevehicle.
6. Route the cables down through the B-pillar taking a 90° turn toenter the B-pillar. Pull the full length of the cables out of the hole atthe base of the B-pillar (Fig. 1) and route towards your switchpanel.
Connecting the Cables:
WARNING! All customer supplied wires that connect to thepositive terminal of the battery must be sized to supply at least125% of the maximum operating current and FUSED at thebattery to carry that load. DO NOT USE CIRCUIT BREAKERSWITH THIS PRODUCT!
Power Cable:
1. Open the wiring shield lid (Fig. 1) and route the power cable intothe wiring shield and towards the firewall.
2. Follow the factory wiring harness through the firewall. It may benecessary to drill a hole in the firewall. If so, be absolutely sure thatthere are no components that could be damaged by drilling. Afterthe hole has been drilled, insert a grommet to protect the cable.
3. Route cable along the factory wiring harness towards the battery.
4. Install a fuse block and fuse (customer supplied) on the end of theRED wire in the power cable. Remove the fuse before connectingany wires to the battery. Fuse 12V models at 20 amps and 24Vmodels at 15 amps.
5. Connect the fuse block to the POSITIVE (+) terminal on the battery.There can not be more than two feet of wire between the fuse blockand the battery. The wire between the fuse block and the battery isunprotected, do not allow it to come into contact with any otherwires.
6.Connect the BLACK wire to the factory chassis ground.
Control Cable:
Extend the control cable to your switch panel and make connections,using the information below. The control cable connects to yourcontrol head or switch box and is fused there. Applying +VBAT to acontrol wire will activate its function. Refer to the wiring diagram onthe next page for wiring and fusing.
Cruise Lights / Auxiliary / White-Orange:
Low Cruise & Auxiliary (default) or High Cruise & Auxiliary or CruiseOff, Auxiliary Only (Activate WHT/ORG wire, then use Scan-Lock toselect).
Low Power / Violet:
The switch type used depends on how you wish Hi/Lo to function:
Latching Mode: Apply +VBAT to the VIOLET wire for less than 1 sec.to “latch” the lightbar into low power. The unit must be turned off andthen back on to restore normal operation. (Momentary Switch)
Level Mode: Apply +VBAT to the VIOLET wire for over 1 sec. to holdthe lightbar in low power until voltage is removed. (Toggle Switch)
Scan-Lock™ / White-Violet:
The WHT/VIO wire allows you to choose from available flash patterns.You must activate the function to select a pattern:
TO CYCLE THROUGH ALL PATTERNS:To cycle forward apply +VBAT to the WHT/VIO wire for less than 1second and release.To cycle backward apply +VBAT to the WHT/VIO wire for more than 1second and release.
TO SET A PATTERN AS DEFAULT:When the pattern is displayed, allow it to run for more than 5 seconds. Thelighthead will now display this pattern when activated.
TO RESET TO THE FACTORY DEFAULT PATTERN:With power off, apply +VBAT to WHT/VIO wire while turning power on.
Use a normally open momentary switch for Scan-Lock operation
DRILLING THE CABLE ACCESS HOLE
Drill cable access hole in appropriate areafor your lightbar (see note)
FRONT OF LIGHTBAR
Forcables exiting
the Driver-sideof the extrusion
lightbarswith
Forcables exiting
the Passenger-sideof the extrusion
lightbarswith
Flash Patterns:1. SignalAlert™ 75 Alternating (default)2. CometFlash® 75 Alternating3. DoubleFlash 150 Alternating4. DoubleFlash 75 Alternating5. SingleFlash 375 Alternating6. SingleFlash 150 Alternating7. SingleFlash 75 Alternating8. ActionFlash™ 75 Alternating
9. ModuFlash™ 75 Alternating10. CalFlash™ Single 75 driver Steady11. Steady12. ActionScan™Traffic Advisor Patterns:1. Sequence to Solid (default setting)2. Sequence On-Sequence Off3. One Lamp: Seq. On to TripleFlash™4. Two Lamp: Seq. On to TripleFlash™
B-Pillar / Inside View
FRONT
Cable Exit Hole
Wire Shield
Fig. 1
Page 3
Fu
se @
20
AM
PS
fo
r 12
V li
gh
tbar
Fu
se @
15
Am
ps
for
24V
lig
htb
ar
WHT/BLU
WHT/GRN
WHT/YEL
WHT/ORG
WHT/BRN
WHT/RED
WHT/BLK
YEL
WHT
BLU/BLK
GRN/BLK
BLU/WHT
GRN/WHT
BLU
GRN
Flashing Alley & TD
TA Right
TA Left
AUX / Cruise Lights
Rear Center LED's
Front Center LEDs
TakeDowns
Passngr Alley
Driver Alley
Rear Inboard
Front Inboard
Rear Outboard
Front Outboard
Rear Corner LEDs
Front Corner LEDs
Wire Color Function
1A
mp
Fu
se
VIOLET
BLK
RED
WHT/VIO
Low Power
Scan-Lock™Momentary Switch
SPST Switch
RED
GRN
WHT
BLK
(+) Driver Brake
(+) Passngr Brake
(+) Taillights
(-) Ground
(+)
Battery
(-)
All Fuses & Switchesare Customer Supplied
Liberty II LC Lightbar / Wiring Diagram
BRACKET, SNAP-IN LT MODULE MT FREEDOM REDESIGN0 7 - 2 6F3 8 2 - 0 0 012
SUB ASSY, FULL LENS, LIBERTY ll LIGHTBAR0 2 - 0 3 6 E 7 7 4 - _ 02
2
SEAL, LENS DIVIDER LIBERTY ll LIGHTBAR3 8 - 0 4 6 E 11 9 - 0 02
DIVIDER, LENS INDEPENDENCE LIGHTBAR3 8 - 0 4 6 E 11 8 - 0 01
8
SUB ASSY, LOW PROFILE MTG FOOT0 2 - 0 3 8 7 3 3 1 - 0 02
LABEL, "FRONT" LIGHTBAR ASSYS1 0 - 0 3 2 2 9 3 5 - 0 01
A/R TY WRAP, 3" BLACK2 6 - 0 2 1 5 0 0 1 - 0 3
4 SCREW, 10-24 X 1.25" WAX DIP SHOULDER PHTX TRI POINT SS1 4 - 1 0 4 2 8 6 - 1 6 J
1 1 0 - 0 5 2 3 9 1 2 - 0 0 LABEL, PN/MN/SN LIBERTY ll
ASSY, HARNESS PHOTO CELL, LEGACY4 6 - 0 7 4 6 8 2 3 - 0 0A/RA/RA/RA/R
A/RA/R A/R
SUB ASSY, CUT LENS, LIBERTY ll LIGHTBAR
6 8 - 1 9 6 F3 6 6 - 3 0 LENS, CLEAR OPTIC CUT CENTER 54" LIBERTY ll
444
1
1 6 8 - 1 9 6 E 7 7 6 - 3 0 LENS, CLEAR OPTIC CUT CENTER LIBERTY ll
22
2 0 2 - 0 3 6 E 7 7 4 1 _ 0
22
2
1
4
2
4
2
2
1
1
2
1
1
2
1
1
812 12
2
1
1
141620
11 1 0 - 0 3 4 6 8 2 4 - 0 0 LABEL, CENTER DOME REMOVAL INSTRUCTIONS
11 - 2 6 E 0 5 6 - 0 2 1
11 - 2 6 E 0 5 6 - 0 1 9
COVER, TOP EXTRUDED 21.665" MACHINED LEGACY
COVER, TOP EXTRUDED 19.275" MACHINED LEGACY
11 -2 6 F3 9 9 - 0 0 0
11 - 2 6 E 3 7 7 - 0 0 9
COVER, TOP EXTRUDED CENTER 54" LIBERTY ll
COVER, TOP EXTRUDED CENTER LEGACY LTBAR
1 5 - 1 0 5 C 7 6 - 1 4 8 SCREW,10 X 7/8 T-25 TORX TRUSS HD PLASTI-LOC SS W/NYSEAL
1 0 - 0 5 2 3 9 2 2 - 0 01 1 11 LABEL, SERIAL NUMBER, LIBERTY ll SERIES
4 6 - 0 7 8 7 7 1 0 - 0 0A/R A/R A/RA/R ASSY, HARNESS EXTERNAL TA CTRL LIBERTY II
A/R A/RA/RA/R ASS'Y, INTERCONNECT CABLE, 17' 61117-1 SCKTS/61118-1 PINS4 6 - 0 7 6 8 2 6 0 - 0 0
A/R A/RA/RA/R HOUSING, 16 POS SCKT COMM MATE-N-LOK3 9 - 0 4 1 6 3 2 3 - 0 4
A/R A/RA/RA/R HOUSING, 12 POS PIN PANEL MT COMM MATE-N-LOK3 9 - 0 4 1 2 0 1 4 - 1 4
A/R A/RA/RA/R ASS'Y TRAFFIC ADV CONTROL HEAD 12V, LED, TACTLD10 1 - 0 6 8 3 8 5 0 - 0 0
2
2
2
2
11
1 1
ASSY, HARNESS "C" 55"-60" LIBERTY II4 6 - 0 7 8 7 7 2 9 - 0 3
ASSY, HARNESS "D" 55"-60" LIBERTY II4 6 - 0 7 8 7 7 2 9 - 0 2
ASSY, HARNESS "E" 55"-60" LIBERTY II4 6 - 0 7 8 7 7 2 9 - 0 1
ASSY, HARNESS "F" 55"-60" LIBERTY II4 6 - 0 7 8 7 7 2 9 - 0 4
SUB ASSY, 3LED HALF TAKE-DOWN LIBERTY II0 1 - 0 2 4 7 2 2 5 - 3 0A/RA/RA/RA/R
SUB ASSY, SINGLE 3LED FULL T-D LIBERTY II0 1 - 0 2 6 F7 6 7 - 3 0A/RA/RA/RA/R
SUB ASSY, HALF TIR TAKE-DOWN LIBERTY II0 1 - 0 2 6 E 7 7 8 - 3 0A/RA/RA/RA/R
BRACKET, MODIFIED BULKHEAD LENS MOUNT LIBERTY II0 7 - 2 4 6 9 1 0 - 0 0 02
ASSY, 4/C 16 GA 20' CABLE0 2 - 0 2 4 1 9 1 2 - 0 1A/RA/RA/RA/R
HOUSING, 6 POS SOCKET CMNL3 9 - 0 4 0 6 3 2 4 - 0 4A/RA/RA/RA/R
ASSY, HARNESS BRAKE/TAIL LTS LIBERTY II4 6 - 0 7 4 7 4 4 7 - 0 0A/RA/RA/RA/R
02 -016G416 -01A/R A/RA/RA/R ASSY, PCB 24V EXPANDED LC I/O FREEDOM IV/LIBERTY II
ASSY,CORNER L-REAR/R-FRONT 24V SINGLE ROW LIBERTY IIA/R A/R A/RA/R 0 1 - 0 2 6 F6 0 9 2 _ _
A/R A/R A/RA/R
SUB ASSY, 6LED FULL DIRECT 24V, LIBERTY IIA/R A/R A/RA/R 0 1 - 0 2 6 F6 0 5 - _ 2
SUB ASSY, SHORT DIRECT 24V LIBERTY II SINGLE COLORA/R A/R A/RA/R 0 1 - 0 2 4 7 1 0 6 - _ 2
SUB ASSY, HALF TIR TAKE-DOWN 24V, LIBERTY IIA/R A/R A/RA/R 0 1 - 0 2 6 E 7 7 8 - 3 2
SUB ASSY, DUAL 3LED FULL T-D 24V, LIBERTY IIA/R A/R A/RA/R 0 1 - 0 2 6 F7 6 8 - 3 2
SUB ASSY,FULL TIR TAKEDOWN 24V LIBERTY IIA/R A/R A/RA/R 0 1 - 0 2 6 F4 4 2 - 3 2
SUB ASSY, 3LED TIR ALLEY LIGHT, 24V, LIBERTY IIA/R A/R A/RA/R 0 1 - 0 2 4 7 1 9 3 - 3 2
0 1 - 0 2 6 F6 0 8 2 _ _ ASSY,CORNER L-FRONT/R-REAR 24V SINGLE ROW LIBERTY II
12 6 8 - 3 9 4 7 1 3 6 - 3 1 LENS, FULL FILTER METALZIED LIBERTY II
6 8 - 3 9 4 7 1 0 0 - 3 1 LENS, HALF FILTER METALIZED LIBERTY II
8
4
12
8
12
4
1 1 0 - 0 3 2 6 4 7 5 - 0 5 LABEL, R1011 1
63
64
65
66
67
68
69
70
71
72
59
60
61
62
73
74
49
82
50
83
51
84
52
85
53
86
54
87
55
88
56
89
57
90
58
91
92
75
76
77
45
78
46
79
47
80
48
81
0 1 - 0 6 8 7 7 1 5 - _ _
1 11 - 3 8 7 2 7 7 - 0 4 4 BASE, EXTRUDED 44.4" MACHINED LEGACY LTBAR
GROMMET, SPECIAL TO BE MOLDED 1.562"2 1 - 11 2 4 5 0 0 4 - 11
PLUG, VENT .750 DIA HOLE LIGHTBAR2 1 - 7 2 6 3 9 9 8 - 0 02
BRACKET, BULKHEAD LENS MOUNT LIBERTY II LIGHTBAR0 7 - 2 6 E 1 2 0 - 0 0 05
INSULATOR, I/O EXTRUSION LIBERTY II3 8 - 0 2 4 7 1 9 1 - 0 02
ASSY, PCB EXPANDED LC I/O FREEDOM IV/LIBERTY II02 -016G416 -001
ASSY,CABLE INPUT 2/C 10 GA 17' LIBERTY ll4 6 - 0 7 4 7 0 2 7 - 1 71
ASS'Y, CABLE INPUT CONTROL FREEDOM/LIBERTY 24 6 - 0 7 4 3 9 0 3 - 1 71
CABLE CLAMP, 5/8"D, 1/2"W .203" MTG HOLE, BLACK2 6 - 0 11 5 6 6 3 - 1 01
NUT, 10-24 CAD PLATED WHIZ OR STEEL ZINC PLATED1 3 - 1 0 4 111 - 0 6 31
TY WRAP, 6" BLACK2 6 - 0 2 1 5 0 0 1 - 0 61
ASSY,CORNER L-FRONT/R-REAR SINGLE ROW LIBERTY II0 1 - 0 2 6 F6 0 8 - _ 0A/R
CORNER L-REAR/R-FRONT SINGLE ROW LIBERTY II0 1 - 0 2 6 F6 0 9 - _ 0A/R
BRACKET, I/O ANCHOR LEGACY LIGHTBAR0 7 - 2 6 D 8 6 5 - 0 0 01
0 1 - 0 2 6 F6 0 6 - _ _A/R
SUB ASSY, FULL TIR TAKE-DOWN LIBERTY ll0 1 - 0 2 6 F4 4 2 - 3 0A/R
SUB ASSY,12V STOP/TURN,TAIL LC LIBERTY II0 1 - 0 2 4 7 1 9 6 - 5 0A/R
0 1 - 0 2 6 F7 6 8 - 3 0A/R
SCREW, 6-32 X 1/2 PPHMS SEMS W/IT LOCK WASHER1 4 - 0 6 2 2 1 6 - 0 8 110
1 SCREW, 10-24 X .875" TX PHD SWEDGE FORM 1/4" LEAD 5/8" THD1 4 - 0 0 2 3 3 4 7 - 0 1
A/R SUB ASSY, PHOTO CELL LC LIBERTY ll0 1 - 0 2 4 7 0 6 5 - 0 1
A/R SUB ASSY, FULL DIRECTIONAL LIBERTY II0 1 - 0 2 6 F6 0 5 - _ 0
2 0 7 - 2 2 3 8 4 1 - 0 0 0 BRACKET, FILLER LEGACY LTBAR
12 0 7 - 2 4 7 3 0 3 - 0 0 0 BRACKET, FULL FILLER LIBERTY II
LIBERTY ll LC LIGHTBAR, 44"
SUB ASSY, DUAL 3LED FULL T-D LIBERTY II
0 1 - 0 6 8 7 7 1 5 - _ _ LIBERTY ll LC LIGHTBAR, 48"
0 1 - 0 6 8 7 7 1 5 - _ _ LIBERTY ll LC LIGHTBAR, 54"
0 1 - 0 6 8 7 7 1 5 - _ _ LIBERTY ll LC LIGHTBAR, 59"
1
1
1
11 1
2
1
2
1
2
1
5
1
5
1
7
1
2
1
1
1
1
1
1
2
1
1
1
1
1
1
2
1
1
1
1
1
1
A/R
A/R
A/R
A/R
A/R
A/R
A/R
A/R
A/R
SUB ASSY, SHORT DIRECTIONAL LIBERTY ll
SUB ASSY, SHORT DUO DIRECTIONAL LIBERTY ll
0 1 - 0 2 4 7 1 0 6 - _ _
0 1 - 0 2 4 7 11 6 - _ _
A/R
A/R
A/R
A/R
A/R
A/R
A/R
A/R
A/R
A/R
A/R
A/R
0 7 - 2 4 7 3 0 4 - 0 0 0 BRACKET, HALF FILLER LIBERTY II
A/R
A/R
A/R
A/R
A/R
A/R
A/R
A/R
A/R
44
8
4
12
8
12
4
0 7 - 2 4 7 1 5 4 - 0 0 02
81212
11 - 3 8 7 2 7 7 - 0 3 9 BASE, EXTRUDED 39.62"" MACHINED LOW PROFILE LTBAR
11 - 3 8 7 3 8 5 - 0 5 0
11 - 3 8 7 3 8 5 - 0 5 5 BASE, MACHINED 55.008" LEGACY LIGHTBAR
BASE, MACHINED 50.228" LEGACY LIGHTBAR
SUB ASSY, FULL DIRECTIONAL DUO LIBERTY II
BRACKET, CENTER FILLER LIBERTY II
SUB ASSY, ALLEY LIBERTY II0 1 - 0 2 4 7 1 9 3 - 3 0A/RA/RA/RA/R
2 222 0 7 - 2 4 7 1 8 7 - 0 0 0 BRACKET, END CLAMP NO ALLEY LIBERTY II
A/R A/RA/RA/R
A/R A/RA/RA/R
A/R A/RA/RA/R
6 8 - 3 9 6 F5 7 7 - _ _ LENS, CORNER FILTER NON OPTIC LIBERTY II
LENS, FILTER FULL LINEAR NON OPTIC LIBERTY II6 8 - 3 9 4 7 1 3 6 - _ _
LENS, HALF FILTER NON OPTIC REFLECTOR LIBERTY II6 8 - 3 9 4 7 1 0 0 - _ _
1111
22
22
22
11
11
22
4 6 - 0 7 8 7 7 2 8 - 0 1 ASSY, HARNESS "A" LIBERTY II LIGHTBAR
ASSY, HARNESS "B" LIBERTY II LIGHTBAR4 6 - 0 7 8 7 7 2 8 - 0 3
ASSY, HARNESS "C" LIBERTY II LIGHTBAR4 6 - 0 7 8 7 7 2 8 - 0 4
ASSY, HARNESS "D" LIBERTY II LIGHTBAR4 6 - 0 7 8 7 7 2 8 - 0 2
ASSY, HARNESS "E" LIBERTY II LIGHTBAR4 6 - 0 7 8 7 7 2 8 - 0 0
ASSY, HARNESS "F" LIBERTY II LIGHTBAR4 6 - 0 7 8 7 7 2 8 - 0 5
ASSY, HARNESS "B" 55"-60" LIBERTY II4 6 - 0 7 8 7 7 2 9 - 0 0
4 444 0 7 - 2 2 6 2 7 5 - 0 0 0 BRACKET, CORNER CLAMP LIBERTY II
2
3
ITEM PART NUMBER DESCRIPTIONQTY QTY QTY QTY
11
12
13
14
15
16
17
18
19
20
4
5
6
7
8
9
10
1
21
22
30
31
32
33
34
35
36
37
38
39
23
24
25
26
27
28
29
40
41
42
43
44
Page 4
65
CO
RN
ER
LE
NS
FIL
TE
R O
PT
ION
82
22
20
9
24
21
19
23
83
53
52
57
55
61 8
68
64
59
58
64
62
63
26
84
2 43
7
FU
LL
DIR
EC
TIO
NA
LL
EN
S F
ILT
ER
27
90
BR
AC
KE
TC
EN
TE
RF
ILL
ER
44"
36
BR
AC
KE
TH
AL
FF
ILL
ER
35
SH
OR
TD
IRE
CT
ION
AL
LE
NS
FIL
TE
R
30
91
22
25
1 3
PH
OT
O C
EL
L
18
BR
AC
KE
TF
UL
LF
ILL
ER
34
20
23
83
25
50
20
FU
LL
DIR
EC
TIO
NA
L
25
26
84
SH
OR
TD
IRE
CT
ION
AL
20
18
12
FU
LL
TIR
TAK
ED
OW
N
31
88
28
29
85
LRAL
LEY
LIG
HT
21
89
82
3 L
ED
HA
LF
TD
75
6 L
ED
HA
LF
TD
77
86
3 L
ED
FU
LL
TD
76
54
FULL
SIN
GLE
TIR
TA
KE
DO
WN
32
87
68
60
BR
AK
E/T
AIL
/TU
RN
33
Page 5
CENTER OPTIONS
CENTER OPTION54" LIGHTBAR
REAR OF B
AR
9
2
4
7
6
8
3
5
11
11
10
10
WHITE/BLUE - FLASHING ALLEY & TD
WHITE/BLUE - FLASHING ALLEY & TD
RED/WHT - FRONT MIDDLE
RED/WHT - FRONT MIDDLE
RED/BLK - REAR MIDDLE
RED/BLK - REAR MIDDLE
WHITE/VIO - SCAN-LOCK
WHITE/VIO - SCAN-LOCK
RED - N/A
RED - N/A
VIOLET - LOW POWER
VIOLET - LOW POWER
WHITE/GRN - TA RIGHT
WHITE/GRN - TA RIGHT
WHITE/YEL - TA LEFT
WHITE/YEL - TA LEFT
WHITE/ORG - AUX / CRUISE LIGHTS
WHITE/ORG - AUX / CRUISE LIGHTS
WHITE/BRN - REAR CENTER LED'S
WHITE/BRN - REAR CENTER LED'S
WHITE/RED - FRONT CENTER LED'S
WHITE/RED - FRONT CENTER LED'S
WHITE/BLK - TAKE-DOWN LIGHTS
WHITE/BLK - TAKE-DOWN LIGHTS
YELLOW - PASSENGER ALLEY LIGHT
YELLOW - PASSENGER ALLEY LIGHT
WHITE - DRIVER ALLEY LIGHT
WHITE - DRIVER ALLEY LIGHT
BLUE/BLK - REAR INBOARD LED'S
BLUE/BLK - REAR INBOARD LED'S
GREEN/BLK - FRONT INBOARD LED'S
GREEN/BLK - FRONT INBOARD LED'S
BLUE/WHT - REAR OUTBOARD LED'S
BLUE/WHT - REAR OUTBOARD LED'S
GREEN/WHT - FRONT OUTBOARD LED'S
GREEN/WHT - FRONT OUTBOARD LED'S
RED = (+) POSITIVE
RED = (+) POSITIVE
BLACK = (-) NEGATIVE
BLACK = (-) NEGATIVE
BLUE - REAR CORNER LED'S
BLUE - REAR CORNER LED'S
GREEN - FRONT CORNER LED'S
GREEN - FRONT CORNER LED'S
17
5455
61
58
51
56
15 16
19
53
62
23
17
22
49
21
18
60 2017
66
REAR
OF B
AR
1
CENTER OPTION, 48" LIGHTBAR
6
3
5
4
7
8
9
49
53
2017
56
55
66
15 16
17
2123
17
22
60
18
19
52
61
59
54
62
CENTER STROBE
37
3536
D U A LLINEAR,CENTER
2627
SHORT DIRECTIONAL
2425
LIGHTED SIGN
SIGN GRAPHIC TO BE DETERMINED
BYCUSTOM
ER ORDER.
67
69
68GTT EMITTER
WIRING SCHEMATIC FOR EMITTER
POS. 1 = GRAY - SERIAL COMMUNICATIONS "B"
POS. 5 = N/C
POS. 6 = BLUE - SERIAL COMMUNICATIONS "A"
POS. 3 = ORANGE - RANGE SETTING
POS. 7 = BLACK - DC GROUND
POS. 8 = GREEN - DC RETURN (INDICATOR LIGHT)
POS. 4 = RED - +12VDC
POS. 2 = WHITE - DISABLE INPUT
33 34
3031
32
HALF 3 LED SILICONE TD
CENTER SILICONE TD
29
28
Refer to parts list on next pageCenter Options
Page 6
6 8 - 3 9 4 7 1 0 0 - 3 1 LENS, HALF FILTER METALIZED LIBERTY II
EMITTER, LED LOW PROFILE GTT MODEL 795H PROGRAMMED
CABLE GTT LED EMITTER 17'4 6 - 0 7 4 3 8 2 5 - 1 7
0 1 - 1 3 1 7 9 2 1 - 0 1
1 5 - 0 4 5 2 1 6 - 0 6 0 SCREW, 4 X 3/8 PFH PLASTI-LOC 410 SS
0 1 - 0 2 6 F8 9 0 - 3 3 SUB ASSY, 3TIR TAKEDOWN W/W CENTER OPT EMITTER LIBERTY II
0 7 - 2 6F7 2 1 - 0 0 0 BRACKET, GTT EMITTER W/T-DS LIBERTY II
4 6 - 0 7 4 7 2 9 5 - 0 0 INPUT CABLE CTR STROBE LIBERTY II
0 1 - 0 2 6 F9 1 4 - 3 3
0 1 - 0 2 6 F9 1 4 - 0 0 SUB ASSY, CENTER STROBE LIBERTY II
SUB ASSY, CENTER STROBE W/T-DS LIBERTY II
1 BASE, EXTRUDED 44.4" MACHINED LEGACY LTBAR
GROMMET, SPECIAL TO BE MOLDED 1.562"1
PLUG, VENT .750 DIA HOLE LIGHTBAR2
BRACKET, BULKHEAD LENS MOUNT LIBERTY II LIGHTBAR6
INSULATOR, I/O EXTRUSION LIBERTY II2
PCB EXPANDED LC I/O FREEDOM IV/LIBERTY II1
CABLE INPUT 2/C 10 GA 17' LIBERTY ll1
CABLE INPUT CONTROL 17' FREEDOM/LIBERTY 21
CABLE CLAMP, 5/8"D, 1/2"W .203" MTG HOLE, BLACK1
NUT, 10-24 CAD PLATED WHIZ OR STEEL ZINC PLATED1
TY WRAP, 6" BLACK1
CORNER L-FRONT/R-REAR SINGLE ROW LIBERTY IIA/R
CORNER L-REAR/R-FRONT SINGLE ROW LIBERTY IIA/R
BRACKET, I/O ANCHOR LEGACY LIGHTBAR1
BRACKET, SNAP-IN LT MODULE MT FREEDOM REDESIGN16
SCREW, 6-32 X 1/2 PPHMS SEMS W/IT LOCK WASHER12
2
2
1 SCREW, 10-24 X .875" TX PHD SWEDGE FORM 1/4" LEAD 5/8" THD
A/R TY WRAP, 3" BLACK
4
4 BRACKET, FILLER LEGACY LTBAR
8 BRACKET, FULL FILLER LIBERTY II
48" LIBERTY ll CENTER OPTION, LC
1
1
2
1
7
1
2
1
1
1
1
1
1
A/R
A/R
8 BRACKET, HALF FILLER LIBERTY II
A/R
4
8
12
4
1 1
12
2
20
BASE, MACHINED 50.228" LEGACY LIGHTBAR
1 1
22 BRACKET, END CLAMP NO ALLEY LIBERTY II
11
2
2
2
1
1
2
2
2
1
1
HARNESS "A" LIBERTY II LIGHTBAR
44 BRACKET, CORNER CLAMP LIBERTY II
4
2
12
2
1
1
4
2
2
1
1
12
11
1 1
2
54" LIBERTY ll CENTER OPTION, LC
OPT OPT SUB ASSY, 3LED TIR ALLEY LIGHT LIBERTY II
OPT OPT SUB ASSY, DUAL LINEAR CENTER OPTION SOLO LIBERTY II
OPTOPT SUB ASSY, DUAL LINEAR CENTER OPTION DUO LIBERTY II
OPTOPT
OPTOPT
OPTOPT SUB ASSY,SHORT DIRECTIONAL LIBERTY II DUO COLOR
OPTOPT SUB ASSY, SHORT DIRECTIONAL LIBERTY II
OPT OPT
OPT OPT
REF.REF.
OPTOPT
OPT OPT
OPT OPT
OPT OPT
OPT OPT
OPT
OPT
OPT
OPT
OPT
OPT 1 4 - 0 4 0 11 6 - 0 4 V SCREW, 4-40 X 1/4 P100FH/CSNK 410 SS VIBRA-TITE
8 6 8 - 3 9 4 7 1 3 6 - 3 1 LENS, FULL FILTER METALIZED LIBERTY II
8
8
12
0 1 - 0 2 6 H 3 6 5 - 3 0
0 1 - 0 2 6 H 1 8 5 - 3 0 SUB ASSY, SILICONE CENTER T-D LIBERTY II
SUB ASSY, 3LED SHORT SILICONE T-D LIBERTY II
2
3
ITEM PART NUMBER DESCRIPTIONQTY QTY
11
12
13
14
15
16
17
18
19
20
4
5
6
7
8
9
10
1
21
22
30
31
32
33
34
35
36
37
38
39
23
24
25
26
27
28
29
40
41
49
50
51
52
53
54
55
56
57
58
42
43
44
45
46
47
48
59
60
61
62
63
64
66
67
68
69
70
71
Part listings for Center Options (Page 5)
NOTE: Not all Items in list appear in parts drawing.
11 - 3 8 7 2 7 7 - 0 4 4
2 1 - 11 2 4 5 0 0 4 - 1
2 1 - 7 2 6 3 9 9 8 - 0 0
0 7 - 2 6 E 1 2 0 - 0 0 0
3 8 - 0 2 4 7 1 9 1 - 0 0
0 2 - 0 1 6 G 4 1 6 - 0 0
4 6 - 0 7 4 7 0 2 7 - 1 7
4 6 - 0 7 4 3 9 0 3 - 1 7
2 6 - 0 11 5 6 6 3 - 1 0
1 3 - 1 0 4 111 - 0 6 3
2 6 - 0 2 1 5 0 0 1 - 0 6
0 1 - 0 2 6F6 0 8 - * 0
0 1 - 0 2 6F6 0 9 - _ 0
0 7 - 2 6 D 8 6 5 - 0 0 0
0 7 - 2 6F3 8 2 - 0 0 0
1 4 - 0 6 2 2 1 6 - 0 8 1
SUB ASSY, CENTER OPTION CUT LENS, LIBERTY ll0 2 - 0 3 6 E 7 7 4 3 _ 0
SEAL, LENS DIVIDER LIBERTY ll LIGHTBAR
DIVIDER, LENS INDEPENDENCE LIGHTBAR
SUB ASSY, LOW PROFILE MTG FOOT
LABEL, "FRONT" LIGHTBAR ASSYS
1 4 - 0 0 2 3 3 4 7 - 0 1
2 6 - 0 2 1 5 0 0 1 - 0 3
SCREW, 10-24 X 1.25" WAX DIP SHOULDER PHTX TRI POINT SS1 4 - 1 0 4 2 8 6 - 1 6 J
0 7 - 2 2 3 8 4 1 - 0 0 0
0 7 - 2 4 7 3 0 3 - 0 0 0
0 1 - 0 6 8 7 7 9 3 - _ _
0 1 - 0 6 8 7 7 9 3 - _ _
0 7 - 2 4 7 3 0 4 - 0 0 0
6 8 - 1 9 6 E 7 7 6 - 3 0 LENS, CLEAR OPTIC CUT CENTER LIBERTY ll
11 - 3 8 7 3 8 5 - 0 5 0
1 0 - 0 3 4 6 8 2 4 - 0 0 LABEL, CENTER DOME REMOVAL INSTRUCTIONS
11 -2 6 F8 8 9 - 0 0 0
11 - 2 6 E 0 5 6 - 0 1 9
COVER, TOP EXTRUDED 16.36" CENTER OPTION LIBERTY II
COVER, TOP EXTRUDED 19.275" MACHINED LEGACY
COVER, TOP EXTRUDED CENTER LEGACY LTBAR
SCREW,10 X 7/8 T-25 TORX TRUSS HD PLASTI-LOC SS W/NYSEAL
LABEL, SERIAL NUMBER, LIBERTY ll SERIES
0 7 - 2 4 7 1 8 7 - 0 0 0
4 6 - 0 7 8 7 7 2 8 - 0 1
HARNESS "B" LIBERTY II LIGHTBAR4 6 - 0 7 8 7 7 2 8 - 0 3
HARNESS "C" LIBERTY II LIGHTBAR4 6 - 0 7 8 7 7 2 8 - 0 4
HARNESS "D" LIBERTY II LIGHTBAR4 6 - 0 7 8 7 7 2 8 - 0 2
HARNESS "E" LIBERTY II LIGHTBAR4 6 - 0 7 8 7 7 2 8 - 0 0
HARNESS "F" LIBERTY II LIGHTBAR4 6 - 0 7 8 7 7 2 8 - 0 5
HARNESS "C" 55"-60" LIBERTY II4 6 - 0 7 8 7 7 2 9 - 0 3
HARNESS "D" 55"-60" LIBERTY II4 6 - 0 7 8 7 7 2 9 - 0 2
HARNESS "B" 55"-60" LIBERTY II4 6 - 0 7 8 7 7 2 9 - 0 0
HARNESS "E" 55"-60" LIBERTY II4 6 - 0 7 8 7 7 2 9 - 0 1
HARNESS "F" 55"-60" LIBERTY II4 6 - 0 7 8 7 7 2 9 - 0 4
0 7 - 2 2 6 2 7 5 - 0 0 0
3 8 - 0 4 6 E 11 9 - 0 0
3 8 - 0 4 6 E 11 8 - 0 0
0 2 - 0 3 8 7 3 3 1 - 0 0
1 0 - 0 3 2 2 9 3 5 - 0 0
1 0 - 0 5 2 3 9 1 2 - 0 0 LABEL, PN/MN/SN LIBERTY ll
11 - 2 6 E 3 7 7 - 0 0 9
1 5 - 1 0 5 C 7 6 - 1 4 8
1 0 - 0 5 2 3 9 2 2 - 0 0
0 2 - 0 3 6 E 7 7 4 1 _ 0 SUB ASSY, CUT LENS, LIBERTY ll
0 1 - 0 2 4 7 1 9 3 - 3 0
0 1 - 0 2 6F8 0 4 - _ 0
0 1 - 0 2 6F7 1 7 - _ _
0 1 - 0 2 4 7 11 6 - _ _
0 1 - 0 2 4 7 1 0 6 - _ 0
SUB ASSY, LIGHTED SIGN, LIBERTY II
PANEL GRAPHIC, LIGHTED SIGN LIBERTY II0 9 - 11 4 7 4 5 0 - _ _
0 1 - 0 2 6 G 1 2 9 - 1 0