1439304 winning fortune, monster progressive, and yi lu fa for blade.pdf

2014 WMS Gaming Inc.

www.wms.com - Product Support Group 1.866.967.4457 - International 34 93 594 87 20

TecDoc13BMar 28, 2014

Installation Bulletin

Overview The purpose of this bulletin is to explain how to install Winning Fortune, Monster Progressive,and Yi Lu Fa for Blade, Figure 1. These themes may be installed as a single-faced bank,side-by-side bank, or double-faced bank. These themes also have an optional sign that maybe installed.Figure 1 Winning Fortune (left), Monster Progressive (middle), and Yi Lu Fa (right).

Affected Equipment

Recommended Readers

Estimated Time to Complete

Revision History

NOTES

These instructions assume that the cabinets have already been installed on a game stand,reference Service Manual 16-1408191: Blade Service Manual.These instructions assume that the cabinets have already been installed with theappropriate appliqu marquee, reference Installation Bulletin 1434253: Install AppliquMarquee on Blade.Yi Lu Fa may only be fielded in Macau. Winning Fortune is the equivalent for all otherinstallations, globally. Do not install Yi Lu Fa in any market other than Macau.

Blade

Field Service Technical Training

2 Hours

Part Number Revision Number Date Changes Initials

1439304 001 March 28, 2014 First initial release JK

Winning Fortune, Monster Progressive, and Yi Lu Fa for Blade1439304Theme Installation

I

OverviewInstallation Bulletin: Winning Fortune, Monster Progressive, and Yi Lu Fa for Blade 2 of 26

ReferenceDocumentation

The documentation below provides reference information for the procedures in this bulletin.

MinimumRequirements

The following must be available and prepared before starting the procedure in this bulletin:

Tools Required The following tools are required to complete the procedure in this bulletin:

Procedure ReferenceInstalling game software Service Manual 16-020832: CPU-NXT, CPU-NXT2, and CPU-NXT3

Operating System (OS) Service Manual and User GuideCPU-NXT3.2 setup Service Manual and User Guide 16-1408348: CPU-NXT3.2 Service

Manual and User GuideInstalling REI media controller Information Bulletin 16-025621: REI Media Controller Must Be

Installed in Approved Location to Avoid OverheatingInstalling LAP Technical Service Bulletin 16-020426: Local Area Progressive

Configuration (LAP-SYS-16 through LAP-SYS-141) Technical Service Bulletin 16-027900: Completing the

Reconciliation Worksheet Installation Bulletin 16-016834: Local Controller for Progressives

(LAP and MLP) Information Bulletin 16-020303: Local Area Progressive (LAP)

Hardware and Software Compatibility ReferenceInstalling Appliqu Marquee on Blade Installation Bulletin 1434253: Install Appliqu Marquee on BladeGeneral Game Cabinet Information - Blade Service Manual 16-1408191: Blade Service ManualInstalling a Blade cabinet onto a game stand Service Manual 16-1408191: Blade Service Manual

64-bit LAP Controller uninterruptible power supply (UPS) game stand overhead display media controller 3.0

step ladder game XML files game and media controller 3.0 OS software

laptop computer jurisdictional and BIOS software RAM clear software for games and mediacontroller 3.0

ESD wrist strap small flathead screwdriver1439304 -- Mar 28, 2014

CAT5 Cable Color CodingInstallation Bulletin: Winning Fortune, Monster Progressive, and Yi Lu Fa for Blade 3 of 26

CAT5 CableColor Coding

This section includes the CAT5 cable color-coded information for easy identification, Table 1.

Parts List Table 2 includes part number information accurate as of the bulletin publication date and issubject to change without notice.

Table 1 CAT5 cable color coding.CAT5 cable Color When to Use

BLUE cAGS (connections to and from: EGMs, network switch, Controller, DHCP Switch, and Router)Ethernet Extenders (connections to and from)

GRAY WAP Connections (to and from Controllers and EGMs)LAP Connections (to and from Controllers and EGMs)

GREEN Daisy chaining EMU connections from EGM to EGM (ie: BBxDs)

RED Portal Controller (connections to and from Controllers and DHCP Switch)Bank Controller (connections to and from Controllers and DHCP Switch)media controller (connections to and from Controllers and DHCP Switch)DHCP Switch (connections to and from EGMs and DHCP Switch)Community Gaming (to and from EMGs when daisy chained)

YELLOW SPN - Serial Peripheral networks (ie: Reel Games)

Table 2 Parts description.Part Number Description

A-029749-00-03 ASSY: AMPRO 1U READYBOX, NO LICKIT-015934-03-00 kit: lap controller components

01-017824-00-00 brkt: Y-board mtg01-018815-00-00 BRKT: RS232/RS485 CONVERTER CVR-BTM01-018816-00-00 BRKT: RS232/RS485 CONVERTER CVR-TOP03-014344 cvr: hpr-pcb-bux20-011989 standoff: 6-32 m-f hex 1.504004-01005-06 4-40x06 phl pan ms st zn6769-020451-00-01 crd: compact flash, w/dma, w/dual plane, 128 MBA-009548-02-00 pcba: wap rj-45 yA-010166-03-00 pcba: rs232/rs485 converterA-011446-01-00 asy: wap RJ45 terminatorHS-011076-00-00 cbl: usb power cableHS-017386-00-00 cable: 60 inch rj-45 to fdb9, un-shieldedHS-017695-00-00 cbl: 3.5mm stereo plug to jack-25'HS-018416-00-18-008 cable: rj45 mld,3', gry

A-026117-07-00 assy: MC3.0 with Calepella20-019570-00-00 ups: 120v, 750va/450w, 5 battery backup/surge, 5 surge1438766 KIT: BLADE WAP Y-board

03-7655-8 clamp: cbl 1/2"08-016398-08 crgt: self seal bbl mailer 9 1/2 x14 1/21438223 BRKT: OPTO PCB YBOARD MTG4006-01027-04 6-32x04 phl rdw ms st zn4408-01128-00 nut: 8-32 keps st znA-009548-02-00 pcba: wap rj-45 y1439304 -- Mar 28, 2014

Parts ListInstallation Bulletin: Winning Fortune, Monster Progressive, and Yi Lu Fa for Blade 4 of 26

HD-009520-00-02 cbl: bulkhead to wap/y brd, 22HS-018416-00-42-008 cbl: rj45 mld, 7', gry

1436027 KIT: MC3.x, LAP Configuration KIT1436026 CBL: DB9M to 14 pin connector(acrosser) with Bracket1436028 CBL: 14 foot CAT 5, Grey, CrossoverA-010166-03-00 pcba: rs232/rs485 converterHS-011076-00-00 cbl: usb power cable

Table 2 Parts description.Part Number Description1439304 -- Mar 28, 2014

Table of ContentsInstallation Bulletin: Winning Fortune, Monster Progressive, and Yi Lu Fa for Blade 5 of 26

Table ofContents

Overview ............................................................................................... 1Reference Documentation..................................................................................... 2Minimum Requirements ........................................................................................ 2Tools Required ...................................................................................................... 2

CAT5 Cable Color Coding.................................................................... 3 Parts List ............................................................................................... 3 Table of Contents ................................................................................. 5 Preventing Injury and Damage............................................................ 6

Preventing Shock................................................................................................... 6Preventing ESD ..................................................................................................... 6

Replacing/Repairing AC Line Cord ................................................................. 6Properly Secure and Vent All Equipment .............................................................. 6Ladder Safety ........................................................................................................ 7

Installation Sequence .......................................................................... 7 Switch and Controller Installation ...................................................... 8

Installing Uninterruptible Power Supply ................................................................. 8Installing Media Controller 3.0............................................................................... 8

Installing LAP Controller ................................................................... 10Installing Local Controller Hardware.................................................................... 11Connecting the Games to the Progressive Network............................................ 14

Setting the Game Jumpers ........................................................................... 15 LAP Reconciliation............................................................................. 15 Connecting cables from the Overhead Display............................... 16 Game Connections and Setup Diagram........................................... 17 Startup Sequence............................................................................... 17

Starting the Media Controller 3.0......................................................................... 18 Configuration and Scheduling .......................................................... 21

Setting Up the Games ......................................................................................... 21 Troubleshooting ................................................................................. 251439304 -- Mar 28, 2014

Preventing Injury and DamageInstallation Bulletin: Winning Fortune, Monster Progressive, and Yi Lu Fa for Blade 6 of 26

PreventingInjury andDamage

This section provides guidelines for preventing electrical injury and protecting componentsfrom electrostatic discharge (ESD) damage.

Preventing Shock ALWAYS power equipment OFF at the Power Switch.Regardless of the type of procedure, set all Power Switches to OFF when servicing thegame, Top Box, or other equipment.

Unplug equipment from the outlet if not handling ESD-sensitive components. Exercise caution when working around electrical equipment.

Preventing ESD ALWAYS wear an ESD wrist strap.Fasten a resistive type (1 or 10 Meg) ESD wrist strap on arm and ensure that it makes goodskin contact, Figure 2 (A). Secure the clip end of the wrist strap to a nearby ground point.Suggested grounds points are: An unpainted or bare exposed metal area of the game cabinet or equipment enclosure. Any labeled ESD common ground point, Figure 2.

Figure 2 ESD wrist strap (left) and ESD common ground point symbol (right).

Ground equipment when handling ESD-sensitive components.When accessing printed circuit boards (PCBs) or components in direct contact with PCBs,including EPROMs, CompactFlash Cards, and PCB connectors, connect the three-prongequipment line cord to a properly grounded outlet. Then, secure the clip end of the ESDwrist strap to an unpainted or bare exposed metal area of the game cabinet or equipmentenclosure.

Replacing/Repairing AC Line CordIf the AC Line Cord is damaged, it must be replaced by the manufacturer (WMS), its serviceagent, or similarly qualified persons in order to avoid a hazard.

Properly Secure andVent All Equipment

Before performing any service tasks, the game (and Top/Accessory Box, if applicable) mustbe properly secured as described in the Service Manual. All WMS cabinets and associatedequipment (including Top/Accessory Box, controllers, etc.) must be properly installed. WMSUpright (BBU/BB2/BB2e/Blade) games must be mounted to a stand using four bolts, and allstands must be bolted to the floor when placed individually or back-to-back, or secured to awall. WMS Slant (BBS/BBS-W/GameField xD) games must be installed back-to-back, or backagainst a wall. WMS Upright and Slant cabinets require a minimum of 6 inches (15 cm)clearance on both sides and at the rear to allow for proper ventilation. WMS BBxD andGameField xD cabinets may be placed directly side by side, but require a minimum of 6 inches(15 cm) clearance at the rear to allow for proper ventilation. Failure to fully secure and ventgames may cause injury and equipment damage.

A1439304 -- Mar 28, 2014

Installation SequenceInstallation Bulletin: Winning Fortune, Monster Progressive, and Yi Lu Fa for Blade 7 of 26

Ladder Safety Observe the following guidelines when using a ladder: Read and follow all instructions from the ladder manufacturer, including labels and markings

on the ladder. Avoid electrical hazards. Do not place a ladder on cables or near electrical outlets. Always inspect the ladder prior to using it. If the ladder is damaged, it must be removed from

service and tagged until repaired or discarded. Do not use a self-supporting ladder (for example, a step ladder) as a single ladder or in a

partially closed position. Do not use the top step or rung of a ladder as a step or rung unless it was designed for that

purpose. Always maintain a 3-point (two hands and a foot, or two feet and a hand) contact on the

ladder when climbing. Keep your body near the middle of the step and always face theladder while climbing.

Only use ladders and appropriate accessories (ladder levelers, jacks or hooks) for theirdesigned purposes.

Ladders must be free of any slippery material on the rungs, steps or feet. Use a ladder only on a stable and level surface. Do not place a ladder on boxes, barrels or other unstable bases to obtain additional height. Do not move or shift a ladder while a person or equipment is on the ladder. A ladder placed in any location where it can be displaced by other work activities, and must

be secured to prevent displacement or a barricade must be erected to keep traffic away fromthe ladder.

Be sure that all locks on an extension ladder are properly engaged. Do not exceed the maximum load rating of a ladder. Be aware of the ladders load rating and

of the weight it is supporting, including the weight of any tools or equipment.

InstallationSequence

Games are installed in the following general sequence:1 The sign vendor installs the overhead display:

a Coordination with WMS Field Service will need to occur to coordinate cabling theoverhead displays.

b Ensures that the overhead display is installed and secured before the media controller3.0 and UPS are placed inside the game stand.

2 WMS Field Service installs all required controllers and hardware into the game stand.3 WMS Field Service configures the controllers:

c WMS Field Service configures the media controller 3.0.d WMS Field Service configures the LAP controller.

4 WMS Field Service configures the EGMs.1439304 -- Mar 28, 2014

Switch and Controller InstallationInstallation Bulletin: Winning Fortune, Monster Progressive, and Yi Lu Fa for Blade 8 of 26

Switch andControllerInstallation

This section provides information on installing the media controller and uninterruptible powersupply (UPS) inside the game stand.

InstallingUninterruptible

Power Supply

Complete the following steps to install the uninterruptible power supply (20-019570-00-00):1 Open a game stand door.2 Install the UPS in a game stand.3 Connect the UPS into an approved 20A/110 VAC circuit.

Installing MediaController 3.0

Due to the high thermal output of the media controller, it must be installed in one of fivespecific locations. For details on where to install the media controller, see Information Bulletin16-025621-xx: REI Media Controller Must Be Installed in Approved Location to AvoidOverheating.

Figure 3 Media controller positionedcorrectly (media controller may look different).

ESDBefore performing the following procedure, see Preventing Injury and Damage on page 6for all appropriate safety and ESD precautions.

NOTEThese installation steps are followed facing the front of the cabinet.

CAUTIONInstall the media controller in the proper upright position, with the port for the power switchon the top, Figure 3 (A). Failure to install the media controller in the correct position maycause it to malfunction.

A1439304 -- Mar 28, 2014

Switch and Controller InstallationInstallation Bulletin: Winning Fortune, Monster Progressive, and Yi Lu Fa for Blade 9 of 26

Complete the following steps to install the media controller (A-026117-07-00):1 Open the game stand door.2 Install the media controller in the game stand, reference information bulletin 16-025621-xx:

REI Media Controller Must Be Installed in Approved Location to Avoid Overheating.3 Plug the power supply cable into the media controller, and connect the other end into the

battery back-up side of the UPS.4 Route the audio and video cables from the sign to the media controller.5 Locate the RS-232 to RS-485 converter (A-010166-03-00) from the kit, Figure 4.

Figure 4 RS-232 to RS-485 converter.

6 Connect the RS-232 to RS-485 converter to the RS232 serial port on the back of themedia controller, Figure 5 (A).

Figure 5 Connect the RS-232 to RS-485 converter.

7 Secure the RS-232 to RS-485 converter using a small flathead screwdriver.8 Plug the USB power cable on the adapter module into one of the USB ports on the back of

the media controller, Figure 5 (B).9 Locate the Ethernet crossover cable (1436028).

NOTEAn Ethernet crossover cable must be used in this procedure.

AB1439304 -- Mar 28, 2014

Installing LAP ControllerInstallation Bulletin: Winning Fortune, Monster Progressive, and Yi Lu Fa for Blade 10 of 26

10 Plug one end of the Ethernet crossover cable into the RS-232 to RS-485 converter plug,Figure 6 (A).

Figure 6 Plug one end of the Ethernet crossover cable.

11 Route the loose end of the Ethernet crossover cable to the last game in the LAP bank.12 Plug the loose end Ethernet crossover cable into the Y-board of the last game,

Figure 7 (A).Figure 7 Plug the loose end Ethernet crossover cableinto the Y-board of the last game.

Installing LAPController

The following section explains the steps necessary to install the LAP controller.

A

A


NOTES

For information on installing the LAP Controller properly into the game stand refer toInstallation Bulletin 16-016834-xx: Local Controller for Progressives (LAP and MLP).Must use LAP-SYS-21 or LAP-SYS-141; refer to Information Bulletin 16-020303: LocalArea Progressive (LAP) Hardware and Software Compatibility Reference.1439304 -- Mar 28, 2014


Installing LocalController Hardware

Complete the following steps to install the hardware for the local controller:1 Connect the RS-232/RS-485 converter (A-010166-03-xx) to COM1, Figure 8 (A).

Figure 8 Connect the LAP controller.

2 Connect the DC power supply to the DC input on the local controller, Figure 8 (B).3 Connect the loose end of the power supply to a power receptacle.4 Secure the RS-485 adapter module using a small flathead screwdriver.5 Connect the CAT5e cable (HS-018416-00-42-008) into the RJ45 plug on the

RS-232/RS-485 converter, Figure 9 (A).Figure 9 CAT5e cable connected to the RS-232/RS-485 converter.

6 Connect the USB power cable on the adapter module into one of the open USB ports onthe local controller, Figure 9 (B).

7 Locate the bottom bracket (01-018815-00-00), Figure 10 (A), and top bracket(01-018816-00-00), Figure 10 (B), to be attached to the RS-232/RS-485 converter.

Figure 10 Top bracket and bottom bracket.

A

B

AB

A

B1439304 -- Mar 28, 2014


8 Attach the bottom bracket to the underside of the converter, Figure 11.Figure 11 Bottom bracket attached to converter.

9 Insert the tabs on the top bracket into the notches in the bottom bracket, Figure 12 (A).Figure 12 Insert tabs on top bracket into notches in bottom bracket.

NOTEEnsure the CAT5e cable, Figure 11 (A), and power connector cable, Figure 11 (B),connected to the RS-232/RS-485 converter are placed between the three standoffs of thebottom bracket, Figure 11.

A

B

A

A1439304 -- Mar 28, 2014


10 Pivot the top bracket down, ensuring that the pins in the top bracket, Figure 13 (A), areinserted into the holes in the bottom bracket, Figure 13 (B).

Figure 13 Lower top bracket.

11 Secure the top bracket and bottom bracket by turning the panel fastener clockwise,Figure 14 (A).

Figure 14 Turn panel fastener clockwise.

12 Route the loose end of the CAT5e cable to the first game in the LAP network.

WARNINGMake sure cables are tucked in and not pinched.

A A B B

A1439304 -- Mar 28, 2014


Connecting theGames to the

ProgressiveNetwork

Complete the following steps to connect the games in the bank to the progressive network:1 On the first game in the bank, connect P1 of the bulkhead-to-progressive board cable

(HD-009520-00-02) to the 10-pin port (J3) on the Y-board, Figure 15 (A).Figure 15 Cables installed into game Y-board.

2 Connect P2 of the bulkhead-to-progressive board cable to the PROGRESSIVE port on theBulkhead Board, Figure 16.

Figure 16 Connection of the bulkhead-to-progressive boardcable into the PROGRESSIVE port.

3 Locate the loose end of the gray CAT5e cable that was connected to the RS-232/RS-485converter in step 5 of the procedure Installing Local Controller Hardware, and connect it toone of the RJ-45 connectors on the Y-board of the first game, Figure 15 (C).

4 Connect the gray CAT5e cable to the remaining RJ-45 connector on the Y-board of the firstgame, Figure 15 (B).

5 Connect the loose end of the gray CAT5e cable to one of the RJ-45 connectors included onthe Y-board in the next game in the bank.

6 In the same way the first and second games were connected in step 4 and step 5,daisy-chain each game in the bank together until the last game is reached.

ABC1439304 -- Mar 28, 2014

LAP ReconciliationInstallation Bulletin: Winning Fortune, Monster Progressive, and Yi Lu Fa for Blade 15 of 26

Setting the Game JumpersOn the bulkhead board, confirm that the progressive jumpers (PROG JMPRS) at JP4 and JP6are set to work with a progressive by completing the following steps:

1 The jumper at JP4 must be set to RS485, Figure 17 (A).Figure 17 Jumper setting at JP4 on bulkhead board.

2 The jumper at JP6 must be set to RS232/485, Figure 18 (A).Figure 18 Jumper setting at JP6 on bulkhead board.

LAPReconciliation

Depending on jurisdictional or site requirements, periodic reconciliation of LAP jackpots may berequired. For step-by-step instructions and a worksheet to complete the task, see TechnicalService Bulletin 16-027900-xx: Completing the Reconciliation Worksheet.

A

A1439304 -- Mar 28, 2014

Connecting Cables from the Overhead DisplayInstallation Bulletin: Winning Fortune, Monster Progressive, and Yi Lu Fa for Blade 16 of 26

ConnectingCables from theOverheadDisplay

After the overhead display has been installed, WMS must work with the installers to ensure itis correctly connected. The power requirements for the overhead display are shown in Table 3.

After the overhead display has been installed, complete the steps below to connect the cables:

1 The sign only has one LCD, plug the DVI cable (HS-024784-00-00) into either DVI port,Figure 19 (A).

Figure 19 DVI connections on media controller (shown lying on side, media controller may look different).

2 Connect the audio cable coming from the sign to the green audio-in port on the back of themedia controller, Figure 19 (B).

Table 3 Overhead display power requirements.

Voltage Power

Line Frequency 60 Hz

Current 20 amp dedicated branch circuit at 120 VAC

NOTES

The video cables used in this procedure are supplied by WMS. The audio cables aresupplied by the overhead display vendor.The overhead display installers must connect the cables to the overhead display.The video cables are shielded.

A

A

B1439304 -- Mar 28, 2014

Game Connections and Setup DiagramInstallation Bulletin: Winning Fortune, Monster Progressive, and Yi Lu Fa for Blade 17 of 26

GameConnectionsand SetupDiagram

This section illustrates how the components connect. Figure 20 illustrates the equipmentlayout and connectivity.For cable legend, see CAT5 Cable Color Coding on page 3.

Figure 20 Equipment layout and connectivity.

StartupSequence

This section provides the procedures necessary to start up network equipment. Follow theprocedures in the sequence provided to avoid communication problems, unnecessary RAMclears, and an inaccurate data record.

NOTEConnect the red CAT5 cables from ETHO 0 on the CPU from each game to the switch.

ESDBefore performing the following procedure, see Preventing Injury and Damage on page 6for all appropriate safety and ESD precautions.1439304 -- Mar 28, 2014

Startup SequenceInstallation Bulletin: Winning Fortune, Monster Progressive, and Yi Lu Fa for Blade 18 of 26

Starting the MediaController 3.0

Complete the following steps to start the media controller 3.0:1 Unlock and open the front cover of the media controller, Figure 21 (A).

Figure 21 Front of media controller 3.0 (shown lying on side with door opening down, media controllermay look different).

2 Attach the ESD wrist strap to the metal handle on the front of the media controller,Figure 21 (B).

3 Insert the RAM clear card (NCLR-MOS-4013) into the CompactFlash slot labeled OS onthe front of the media controller, Figure 21 (C).

4 Turn the media controller ON at the power switch on the back of the media controller,Figure 22 (A).

Figure 22 Connections on media controller 3.0(media controller may look different).

5 Press and hold the POWER button on the front of the media controller, Figure 21 (D), untilthe media controller reboots.

6 Wait several minutes while the media controller performs a RAM clear.

AB E

D

C

A1439304 -- Mar 28, 2014


7 When the RAM clear is completed, Figure 23, press and hold the POWER button,Figure 21 (D), until the fan on the front of the media controller stops.

Figure 23 Screen shown when RAM clear is complete.

8 Write down the MAC address for the eth0. It will be used later in the procedure.9 After the media controller is OFF, remove the RAM clear card, Figure 21 (C).

10 Install the OS CompactFlash card in the slot labeled OS on the front of the mediacontroller, Figure 21 (C).

11 Install the game software CompactFlash card in the slot labeled GAME on the front of themedia controller, Figure 21 (E).

12 Press and hold the POWER button, Figure 21 (D), until the media controller reboots.1439304 -- Mar 28, 2014


13 Determine the following:

Figure 24 Screen shown during reboot if network connection cannot be established.

14 Close and lock the media controller.15 Remove the ESD wrist strap and store it.

If the media controller 3.0... then...

successfully interacts with the network during rebooting

the LCDs display an animation screen. When the overhead display is fully rebooted, the characters move around the screen.

is unable to interact with the network during rebooting, Figure 24

If necessary, complete the following steps to establish the connection to the network:1 Ensure that all gray CAT5e Ethernet cables are connected correctly, Installing

Local Controller Hardware on page 11.2 Perform another RAM clear and then install the game and OS CompactFlash

cards (see step 3 through step 12 of this procedure).

NOTEIf the overhead display does not boot up, do not proceed with the startup sequence. Seethe Troubleshooting section beginning on page 25 for a solution.1439304 -- Mar 28, 2014

Configuration and SchedulingInstallation Bulletin: Winning Fortune, Monster Progressive, and Yi Lu Fa for Blade 21 of 26

Configurationand Scheduling

This section provides procedures for configuring and scheduling options.

Setting Up theGames

Perform the following steps to set up the gaming devices:1 Unlock and open the main door.2 Open the EMI door.3 Ensure power to the game is OFF.4 Attach an ESD wrist strap.5 Unlock and open the CPU-NXT3.2 enclosure door, Figure 25.

Figure 25 CompactFlash card slots.

6 Refer to Service Manual & User Guide 16-1408348: CPU-NXT3.2 Service Manual andUser Guide to perform the following tasks:a Remove the CPU-NXT3.2 from the cabinet and place on a flat non-abrasive surface. b Install the BIOS and jurisdictional software.c Install the hardware key.d Reinstall the CPU-NXT3.2 into the cabinet.e Install the RAM clear CompactFlash card in the OS flash drive, Figure 25 (B).f Power ON the game and perform a RAM clear.g When the RAM clear has completed, power the game OFF.h Remove the RAM clear CompactFlash card.i Install the operating system (OS) CompactFlash card into the OS flash drive,

Figure 25 (B). Use the direction indicator on the CompactFlash card to ensure the cardis correctly oriented and inserted.

j Install the game CompactFlash card in the game flash drive, Figure 25 (C). Use thedirection indicator on the CompactFlash card to ensure the card is correctly orientedand inserted.


NOTEAlthough some screens in this section specify Big Event, they are valid for WinningFortune, Monster Progressive, and Yi Lu Fa.

B C

A1439304 -- Mar 28, 2014


7 Close and lock the CPU-NXT3.2 enclosure door.8 Close the EMI door.9 Power the game ON at the power switch.

10 Press the DIAGNOSTIC button.The Administration Menu displays.

11 Select Setup.The Setup Options menu displays, Figure 26.

Figure 26 Setup Options menu.

12 Configure the games as described in 16-020832-xx: CPU-NXT, CPU-NXT2, andCPU-NXT3 Operating System (OS) Service Manual and User Guide and per thejurisdiction or casino protocol.

13 Select Setup | Comm Setup | Serial Ports, Figure 27.Figure 27 Comm Setup menu.1439304 -- Mar 28, 2014


14 Choose WMSP, Figure 28 (A), and then select Set, Figure 28 (B).Figure 28 Serial Comm Setup.

15 Select Confirm if applicable.

16 From the Administration Menu, select Diagnostics | Machine Info | System Information,Figure 29.

Figure 29 Machine Info Menu.

NOTEIn Comm Setup, ensure the Progressive Type is set to WMSP.

A

B1439304 -- Mar 28, 2014


The System Information screen displays, Figure 30. Figure 30 System Information screen.

17 Scroll to the bottom of the System Info screen to retrieve the EGM MAC address,Figure 30 (A). Make a note of the MAC address.

18 Determine the following:

19 Refer to Technical Service Bulletin 16-020426: Local Area Progressive Configuration(LAP-SYS-16 through LAP-SYS-141) to perform the following tasks: a Connect the LAP controller to the laptop.b Configure the LAP controller with the appropriate information and the MAC address for

each EGM in the bank.c Obtain the media controller MAC Address.d Load XML Files.e Configure the LAP controller.

If all of the games... then...

have been configured proceed to step 19.have NOT been configured return to step 1 and proceed with the next game.

A1439304 -- Mar 28, 2014

TroubleshootingInstallation Bulletin: Winning Fortune, Monster Progressive, and Yi Lu Fa for Blade 25 of 26

Troubleshooting Table 4 provides solutions to problems related to Winning Fortune, Monster Progressive, andYi Lu Fa.

NOTEProblems can also be resolved by calling the WMS Gaming 24-hr Product Support Groupat 1-866-967-4457.

Table 4 Performance issue and solutions.Performance Issue Possible Cause Solution

Server message failure.Server Comm Loss.

Game connected to wrongnetwork.

Bad connections

Ensure game client is connected to correctserver.

Check cable connections

Game clients tilt/powerfailure during bonus.

Power failure. Hardware failure. Game failure.

Check cables and connections and replace ifneeded.

Game is stuck in CallAttendant mode.

Tilt due to software or hardwarefailure.

Power cycle game client controller. RAM clear all games and reconfigure each

game.

Overhead display doesnot boot up. Bad connections.

Follow the steps below:1 Power OFF the media controller 3.0.2 Check all connections.3 RAM clear the media controller 3.04 Power ON the media controller 3.0.

Loss of video duringbonus round. Loose cable.

Follow the steps below:1 Power OFF the media controller 3.0.2 Reconnect the video cable.3 Power OFF the games.4 Power ON the media controller 3.0.5 Power ON the games.NOTE: If bonus was not complete when mediacontroller 3.0 was powered OFF, it will completeafter games are powered ON.

Loss of video when notin bonus round. Loose cable.

Follow the steps below:1 Power OFF the media controller 3.0.2 Reconnect the video cable.3 Power ON the media controller 3.0.

The overhead displaysand all games display novideo, and the ServerComm Loss tilt displayson the games.

Media controller 3.0 is overheateddue to improper installation/poorventilation.

Follow the steps below:1 Install the media controller 3.0 in an approved

location.2 Power cycle the media controller 3.0.3 RAM clear the media controller 3.0.4 Replace the media controller 3.0.5 Perform the required Startup Sequence. See

Startup Sequence on page 17.

On the media controller3.0, the OSCompactFlash Cardejects when the door isclosed and locked.

Media controller 3.0 is positionedvertically so door opens to the right.

Do one of the following: If media controller 3.0 must be positioned

vertically, ensure that door opens to the left. Remove CompactFlash ejector pins.1439304 -- Mar 28, 2014

TroubleshootingInstallation Bulletin: Winning Fortune, Monster Progressive, and Yi Lu Fa for Blade 26 of 26

END OF BULLETIN

System freezes at initialsign display.

Faulty cabling.

Doors open.

No power to switch.

Do the following: Verify power to switch. Check all cabling and doors. If doors and cabling are okay, do the following:

1 RAM clear the media controller 3.0.2 Reboot the system, see Startup Sequence on

page 17.

No Sync displays on theoverhead display(s).

Communication problem betweenmedia controller 3.0 and LCDs.

Do the following: Verify that the DVI cable is properly connected

to the media controller 3.0 and to the LCDs inthe overhead display.

Have the overhead display techs verify that thecorrect firmware is on the LCDs.

Make sure the DVI cable is not pinched. Verify that the video card in the media controller

3.0 is properly connected to the PCI-E slot andthe fans on the video card are running.

If all of the above have been verified, thenreplace the media controller 3.0

NOTE: The LCD must be connected to the mediacontroller 3.0 at boot or nothing will display. If DVIcable is disconnected while media controller 3.0 isrunning video may be lost. The only solution in bothcases is to reboot the media controller 3.0.

No Boot Device Founddisplays on the overheaddisplay(s).

Faulty CompactFlash cards orconnections.

Do the following: Verify that the correct CompactFlash cards are

being used. Get known, good CompactFlash card that works

with media controller 3.0 (RAM clear) and see ifit works correctly.

Open case of media controller 3.0 to make sureall cables are connected (four-pin power andribbon cable).

ERROR: Unable tomount partition/dev/sda1 displays onthe overhead display(s).

Faulty CompactFlash cards,connections, or media controller 3.0.

Follow the steps below:1 Power OFF the media controller 3.0.2 Remove CompactFlash cards.3 Reinstall CompactFlash cards.4 Power ON the media controller 3.0 to see if

problem persists.5 Perform a RAM clear on the media controller

3.0.6 Power ON the media controller 3.0 with

OS/Game CompactFlash cards.7 If problem persists, open media controller 3.0 to

make sure all connections are seated correctly.8 Try new CompactFlash cards.9 Replace media controller 3.0.

Brief loss of power. A power surge has occurred.Follow the steps below:1 Power OFF the media controller 3.0.2 Power ON the media controller 3.0.

Table 4 Performance issue and solutions.Performance Issue Possible Cause Solution1439304 -- Mar 28, 2014

OverviewReference DocumentationMinimum RequirementsTools Required

CAT5 Cable Color CodingParts ListTable of ContentsPreventing Injury and DamagePreventing ShockPreventing ESDReplacing/Repairing AC Line Cord

Properly Secure and Vent All EquipmentLadder Safety

Installation SequenceSwitch and Controller InstallationInstalling Uninterruptible Power SupplyInstalling Media Controller 3.0

Installing LAP ControllerInstalling Local Controller HardwareConnecting the Games to the Progressive NetworkSetting the Game Jumpers

LAP ReconciliationConnecting Cables from the Overhead DisplayGame Connections and Setup DiagramStartup SequenceStarting the Media Controller 3.0

Configuration and SchedulingSetting Up the Games

Troubleshooting

1439304 winning fortune, monster progressive, and yi lu fa for blade.pdf

Documents