13a26
DESCRIPTION
Diagrama tv toshiba modelo:13A26TRANSCRIPT
SERVICE MANUAL
COLOR TELEVISION
DOCUMENT CREATED IN JAPAN, April, 2007 GREEN
13A26
(MFR'S VERSION A)FILE NO. 050-200704GR
The above model is classified as a green product (*1), as indicated by the underlined serial number.
This Service Manual describes replacement parts for the green product. When repairing this green
product, use the part(s) described in this manual and lead-free solder (*2).
For (*1) and (*2), see the next page.
(*1) GREEN PRODUCT PROCUREMENTThe EC is actively promoting the WEEE & RoHS Directives that define standards for recyclingand reuse of Waste Electrical and Electronic Equipment and for the Restriction of the use ofcertain Hazardous Substances. From July 1, 2006, the RoHS Directive will prohibit anymarketing of new products containing the restricted substances.
Increasing attention is given to issues related to the global environmental. Toshiba Corporationrecognizes environmental protection as a key management tasks, and is doing its utmost toenhance and improve the quality and scope of its environmental activities. In line with this,Toshiba proactively promotes Green Procurement, and seeks to purchase and use products,parts and materials that have low environmental impacts.
Green procurement of parts is not only confined to manufacture. The same green parts used inmanufacture must also be used as replacement parts.
(*2) LEAD-FREE SOLDERThis product is manufactured using lead-free solder as a part of a movement within the consumerproducts industry at large to be environmentally responsible. Lead-free solder must be used inthe servicing and repair of this product.
WARNINGThis product is manufactured using lead free solder.
DO NOT USE LEAD BASED SOLDER TO REPAIR THIS PRODUCT !
The melting temperature of lead-free solder is higher than that of leaded solder by 86°F to 104°F(30°C to 40°C). Use of a soldering iron designed for lead-based solders to repair product madewith lead-free solder may result in damage to the component and or PCB being soldered. Greatcare should be made to ensure high-quality soldering when servicing this product especiallywhen soldering large components, through-hole pins, and on PCBs as the level of heatrequired to melt lead-free solder is high.
A1-1
SERVICING NOTICES ON CHECKING
6. AVOID AN X-RAY1. KEEP THE NOTICES
As for the places which need special attentions,they are indicated with the labels or seals on thecabinet, chassis and parts. Make sure to keep theindications and notices in the operation manual.
3. USE THE DESIGNATED PARTS
5. TAKE CARE TO DEAL WITH THECATHODE-RAY TUBE
Safety is secured against an X-ray by consider-ing about the cathode-ray tube and the highvoltage peripheral circuit, etc.Therefore, when repairing the high voltage pe-ripheral circuit, use the designated parts andmake sure not modify the circuit.Repairing except indicates causes rising of highvoltage, and it emits an X-ray from the cathode-ray tube.
Please include the following informations when you order parts. (Particularly the VERSION LETTER.)1. MODEL NUMBER and VERSION LETTER
The MODEL NUMBER can be found on the back of each product and the VERSION LETTER can be found at the end of the SERIAL NUMBER.2. PART NO. and DESCRIPTION
You can find it in your SERVICE MANUAL.
HOW TO ORDER PARTS
When you exchange IC and Transistor with a heat sink, apply silicon grease on the contact section ofthe heat sink. Befor applying new silicon grease, remove all the old silicon grease. (Old grease maycause damages to the IC and Transistor.)
IMPORTANT
2. AVOID AN ELECTRIC SHOCKThere is a high voltage part inside. Avoid anelectric shock while the electric current isflowing.
The parts in this equipment have the specificcharacters of incombustibility and withstandvoltage for safety. Therefore, the part which isreplaced should be used the part which hasthe same character.Especially as to the important parts for safetywhich is indicated in the circuit diagram or thetable of parts as a mark, the designatedparts must be used.
4. PUT PARTS AND WIRES IN THEORIGINAL POSITION AFTERASSEMBLING OR WIRINGThere are parts which use the insulationmaterial such as a tube or tape for safety, orwhich are assembled in the condition thatthese do not contact with the printed board.The inside wiring is designed not to get closerto the pyrogenic parts and high voltage parts.Therefore, put these parts in the originalpositions.
In the condition that an explosion-proof cathode-ray tube is set in this equipment, safety issecured against implosion. However, whenremoving it or serving from backward, it isdangerous to give a shock. Take enough care todeal with it.
PERFORM A SAFETY CHECK AFTERSERVICING
7.
Confirm that the screws, parts and wiring whichwere removed in order to service are put in theoriginal positions, or whether there are theportions which are deteriorated around theserviced places serviced or not. Check theinsulation between the antenna terminal orexternal metal and the AC cord plug blades.And be sure the safety of that.(INSULATION CHECK PROCEDURE)
1.2.
3.
4.
Unplug the plug from the AC outlet.Remove the antenna terminal on TV and turnon the TV.Insulation resistance between the cord plugterminals and the eternal exposure metal[Note 2] should be more than 1M ohm byusing the 500V insulation resistance meter[Note 1] .If the insulation resistance is less than 1Mohm, the inspection repair should berequired.
[Note 1]
If you have not the 500V insulationresistance meter, use a Tester.
[Note 2]External exposure metal: Antenna terminal
Headphone jack
A1-2
TABLE OF CONTENTS
GREEN PRODUCT PROCUREMENT ..........................................................................................
LEAD-FREE SOLDER ..................................................................................................................
SERVICING NOTICES ON CHECKING ......................................................................................
HOW TO ORDER PARTS ............................................................................................................
IMPORTANT .................................................................................................................................
TABLE OF CONTENTS ...............................................................................................................
GENERAL SPECIFICATIONS .....................................................................................................
DISASSEMBLY INSTRUCTIONS
1. REMOVAL OF ANODE CAP ................................................................................................
2. REMOVAL AND INSTALLATION OF FLAT PACKAGE IC .................................................
SERVICE MODE LIST .................................................................................................................
CONFIRMATION OF HOURS USED ..........................................................................................
WHEN REPLACING EEPROM (MEMORY) IC ...........................................................................
ELECTRICAL ADJUSTMENTS ...................................................................................................
BLOCK DIAGRAMS .....................................................................................................................
PRINTED CIRCUIT BOARDS
TV MT/CRT ...............................................................................................................................
TV MT........................................................................................................................................
SCHEMATIC DIAGRAMS
MICON/CHROMA/TUNER ........................................................................................................
TV POWER ...............................................................................................................................
DEFLECTION/CRT ...................................................................................................................
SOUND/AV ................................................................................................................................
WAVEFORMS ...............................................................................................................................
MECHANICAL EXPLODED VIEWS ............................................................................................
MECHANICAL REPLACEMENT PARTS LIST ...........................................................................
ELECTRICAL REPLACEMENT PARTS LIST ............................................................................
A1-1
A1-1
A1-2
A1-2
A1-2
A2-1
A3-1~A3-5
B1-1
B2-1, B2-2
C-1
C-3
C-3
D-1~D-4
E-1, E-2
F-1, F-2
F-3, F-4
G-1, G-2
G-3, G-4
G-5, G-6
G-7, G-8
H-1, H-2
I-1, I-2
J1-1
J2-1~J2-3
A2-1
GENERAL SPECIFICATIONSG-1 TV CRT CRT Size / Visual Size 13 inch / 335.4mmV
System CRT Type Normal Deflection 90 degreeMagnetic Field BV/BH +0.45G/0.18G
Color System NTSCSpeaker 1Speaker
Position BottomSize 3 InchImpedance 8 ohm
Sound Output MAX 1.0 W10%(Typical) --- W
NTSC3.58+4.43 /PAL60Hz NoG-2 Tuning Broadcasting System US System M
System Tuner and System 1Tuner Receive CH Destination USA(W/ CATV)
Tuning System F-SynthInput Impedance VHF/UHF 75 ohm
2 - 69, 4A, A-5 - A-1, CH Coverage A - I, J - W, W+1 - W+84
Intermediate Picture(FP) 45.75MHzFrequency Sound(FS) 41.25MHz
FP-FS 4.50MHzPreset CH NoStereo/Dual TV Sound NoTuner Sound Muting Yes
G-3 Power Power Source AC 120V AC 60HzDC
Power Consumption at AC 54 W at AC 120 V 60 Hz
Stand by (at AC) 3 W at AC 120 V 60 HzPer Year -- kWh/Year
Protector Power Fuse YesG-4 Regulation Safety UL(UL1492)
Radiation ---X-Radiation DHHS
G-5 Temperature Operation +5oC ~ +40oCStorage -20oC ~ +60oC
G-6 Operating Humidity Less than 80% RH
A3-1
GENERAL SPECIFICATIONSG-7 On Screen Menu Yes
Display Menu Type CharacterPicture Yes
Contrast YesBrightness YesColor YesTint YesSharpness Yes
Audio NoBass NoTreble NoBalance NoBBE On/Off NoStable Sound On/Off No
CH Set Up YesTV/CABLE(CATV) YesAuto CH Memory YesAdd/ Delete Yes
Language YesV-chip YesLock YesOn Timer Yes
CH Label NoFavorite CH NoColor Stream DVD/DTV No
Control Level YesVolume YesBrightness YesContrast YesColor YesTint YesSharpness YesTuning NoBass NoTreble NoBalance NoBack Light No
Stereo,Audio Output,SAP NoVideo YesColor Stream NoChannel(TV/Cable) YesCH Label NoGame Timer YesSleep Timer YesSound Mute YesV-chip Rating Yes
G-8 OSD Language English French Spanish
G-9 Clock and Sleep Timer Max Time 120 Min Timer Step 10 Min
On Timer Program(On Timer ) YesWake Up Timer NoTimer Back-up (at Power Off Mode) more than -- Min Sec
A3-2
GENERAL SPECIFICATIONSG-10 Remote Unit RC-EH
Control Glow in Dark Remocon YesFormat ToshibaCustom Code 40-BF hPower Source Voltage(D.C) 3V
UM size x pcs UM-4 x 2 pcs Total Keys 27 KeysKeys Power Yes
1 Yes2 Yes3 Yes4 Yes5 Yes6 Yes7 Yes8 Yes9 Yes0 Yes100 NoCH Up YesCH Down YesVolume Up YesVolume Down YesTV/Caption/Text YesCH1/CH2 YesTV/Video(TV/AV) YesCH RTN/CH ENT(Quick View) YesSleep YesRE Call(Call) YesReset YesMenu YesEnter YesMute YesExit NoMTS(Audio Select) NoSet + YesSet - Yes
Multi Brand Keys CH Up(VCR) NoCH Down(VCR) NoPause/Still NoTV/VCR(VCR) NoCode NoFF NoRew NoRec NoPlay NoStop NoTV NoVCR NoCable No
A3-3
GENERAL SPECIFICATIONSG-11 Features Auto Degauss Yes
Auto Shut Off YesCanal+ NoCATV YesAnti-theft NoRental NoMemory(Last CH) YesMemory(Last Volume) YesV-Chip Yes
Type USA,ORION TypeBBE NoAuto Search NoCH Allocation NoSAP NoChannel Lock NoJust Clock Function NoGame Position NoCH Label NoVM Circuit NoFull OSD NoPremiere NoComb Filter No
LinesAuto CH Memory YesHotel Lock NoClosed Caption YesFBT Leak Test Protect YesCH Lock YesVideo Lock YesGame Timer (Max Time:120 Min) YesStable Sound NoEnergy Star NoPower On Memory YesFavorite CH No
G-12 Accessories Owner's Manual Language English/Spanishw/Guarantee Card No
Remote Control Unit YesRod Antenna No
PolesTerminal
Loop Antenna NoTerminal -
U/V Mixer NoDC Car Cord (Center+) NoGuarantee Card YesWarning Sheet NoCircuit Diagram NoAntenna Change Plug NoService Facility List NoImportant Safeguard NoDew/AHC Caution Sheet NoAC Plug Adapter NoQuick Set-up Sheet NoBattery Yes
UM size x pcs UM-4 x 2 pcs OEM Brand No
AC Cord NoAV Cord (2Pin-1Pin) NoRegistration Card (NDL Card) NoESP Card No300 ohm to 75 ohm Antenna Adapter No
A3-4
GENERAL SPECIFICATIONSG-13 Interface Switch Front Power Yes
System Select No Main Power SW No Sub Power No Channel Up/Reset YesChannel Down/Enter YesVolume Up/Set Up YesVolume Down/Set Down YesMENU=Volume Up+Volume Down Yes
Rear AC/DC No TV/CATV Selector No Degauss No Main Power SW No
Indicator Power YesStand-by NoOn Timer No
Terminals Front Video Input RCA Audio Input RCA x 1 Other Terminal Ear Phone
Rear Video Input(Rear1) NoVideo Input(Rear2) NoAudio Input(Rear1) NoAudio Input(Rear2) NoVideo Output NoAudio Output NoEuro Scart NoColor Stream NoDiversity NoExt Speaker NoDC Jack 12V(Center +) NoVHF/UHF Antenna Input F TypeAC Outlet No
G-14 Set Size Approx. W x D x H (mm) 362 x 360 x 320.5 G-15 Weight Net (Approx.) 9.5 kg ( 20.9 lbs)
Gross (Approx.) 11.0kg ( 24.4lbs)G-16 Carton Master Carton No
Content ---- SetsMaterial -- /--Dimensions W x D x H(mm) -- x -- x -- Description of Origin No
Gift Box Material Double/BrownDimensions W x D x H(mm) 440 x 408 x 380 Description of Origin Yes
Drop Test Natural Dropping At 1 Corner / 3 Edges / 6 Surfaces
Height (cm) 62 Container Stuffing 866 Sets/40' container
G-17 Cabinet Material Cabinet Cabinet Front PS 94V0 DECABROM Cabinet Rear PS 94V0 DECABROM
PCB Non-Halogen Demand NoEyelet Demand Yes
G-18 Environment Environmental standard requirement Green procurement of TOSHIBAPb-free Phase3(Phase3A)
A3-5
B1-1
1. REMOVAL OF ANODE CAPRead the following NOTED items before starting work.
After turning the power off there might still be a potentialvoltage that is very dangerous. When removing theAnode Cap, make sure to discharge the Anode Cap'spotential voltage.Do not use pliers to loosen or tighten the Anode Capterminal, this may cause the spring to be damaged.
*
*
REMOVAL
1. Follow the steps as follows to discharge the Anode Cap.(Refer to Fig. 1-1.)Connect one end of an Alligator Clip to the metal part of aflat-blade screwdriver and the other end to ground.While holding the plastic part of the insulated Screwdriver,touch the support of the Anode with the tip of theScrewdriver.A cracking noise will be heard as the voltage is discharged.
Flip up the sides of the Rubber Cap in the direction of thearrow and remove one side of the support.(Refer to Fig. 1-2.)
2.
DISASSEMBLY INSTRUCTIONS
GND on the CRT
Screwdriver
Alligator Clip
SupportCRT
GND on the CRT
Rubber Cap
CRTSupport
Fig. 1-1
Fig. 1-2
3. After one side is removed, pull in the opposite direction toremove the other.
NOTE
Take care not to damage the Rubber Cap.
INSTALLATION
1. Clean the spot where the cap was located with a smallamount of alcohol. (Refer to Fig. 1-3.)
Location of Anode Cap
Fig. 1-3
NOTE
Confirm that there is no dirt, dust, etc. at the spot wherethe cap was located.
2.
3.
Arrange the wire of the Anode Cap and make sure thewire is not twisted.Turn over the Rubber Cap. (Refer to Fig. 1-4.)
Fig. 1-4
4. Insert one end of the Anode Support into the anode button,then the other as shown in Fig. 1-5 .
5.6.
Confirm that the Support is securely connected.Put on the Rubber Cap without moving any parts.
CRTSupport
Fig. 1-5
B2-1
Masking Tape(Cotton Tape)
DISASSEMBLY INSTRUCTIONS
2.
REMOVAL
IC
Put the Masking Tape (cotton tape) around the FlatPackage IC to protect other parts from any damage.(Refer to Fig. 2-1.)
1.
Fig. 2-1
NOTE
REMOVAL AND INSTALLATION OFFLAT PACKAGE IC
Some ICs on the PCB are affixed with glue, so becareful not to break or damage the foil of each IC leadsor solder lands under the IC when removing it.
NOTE
Masking is carried out on all the parts located within 10mm distance from IC leads.
Blower type ICdesoldering machine
IC
Heat the IC leads using a blower type IC desolderingmachine. (Refer to Fig. 2-2.)
2.
Fig. 2-2
NOTE
Do not add the rotating and the back and forthdirections force on the IC, until IC can move back andforth easily after desoldering the IC leads completely.
When IC starts moving back and forth easily afterdesoldering completely, pickup the corner of the IC using atweezers and remove the IC by moving with the ICdesoldering machine. (Refer to Fig. 2-3.)
3.
Blower type ICdesolderingmachine
IC
Fig. 2-3
Tweezers
Peel off the Masking Tape.4.
Absorb the solder left on the pattern using the BraidedShield Wire. (Refer to Fig. 2-4.)
5.
NOTE
Do not move the Braided Shield Wire in the verticaldirection towards the IC pattern.
Braided Shield Wire
Soldering Iron
Fig. 2-4IC pattern
B2-2
DISASSEMBLY INSTRUCTIONS
Supply solderingfrom upper positionto lower position
IC
Supply the solder from the upper position of IC leadssliding to the lower position of the IC leads. (Refer to Fig. 2-6.)
2.
Fig. 2-6
Soldering IronSolder
IC
Absorb the solder left on the lead using the Braided ShieldWire. (Refer to Fig. 2-7.)
3.
Fig. 2-7
Soldering Iron
Braided Shield Wire
NOTE
Do not absorb the solder to excess.
IC
When bridge-soldering between terminals and/or thesoldering amount are not enough, resolder using a Thin-tipSoldering Iron. (Refer to Fig. 2-8.)
4.
Fig. 2-8
Thin-tip Soldering Iron
NOTE
When the IC leads are bent during soldering and/orrepairing, do not repair the bending of leads. If thebending of leads are repaired, the pattern may bedamaged. So, always be sure to replace the IC in thiscase.
Finally, confirm the soldering status on four sides of the ICusing a magnifying glass.Confirm that no abnormality is found on the solderingposition and installation position of the parts around the IC.If some abnormality is found, correct by resoldering.
5.Solder temporarily
Soldering Iron
INSTALLATION
Take care of the polarity of new IC and then install the newIC fitting on the printed circuit pattern. Then solder eachlead on the diagonal positions of IC temporarily.(Refer to Fig. 2-5.)
1.
Fig. 2-5
Solder temporarily
C-1
SERVICE MODE LIST
CONFIRMATION OF HOURS USEDPOWER ON total hours can be checked on the screen. Total hours are displayed in 16 system of notation.
NOTE: If you set factory initialization, the total hours is reset to "0".
1.2.
3.
Set the VOLUME to minimum.Press both VOL. DOWN button on the set and Channelbutton (6) on the remote control for more than 2 seconds.After the confirmation of using hours, turn off the power.
FIG. 1
Initial setting content of MEMORY IC.
POWER ON total hours. = (16 x 16 x 16 x thousands digit value) + (16 x 16 x hundreds digit value) + (16 x tens digit value) + (ones digit value)
ADDRESS DATA
INIT 00 D0
CRT ON 0010
WHEN REPLACING EEPROM (MEMORY) IC
If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken toensure correct data settings while making reference to TABLE 1.
Table 1
+9+2INI +0 +1 +3 +4 +5 +6 +7
00
+8 +A
47 B3 24 69 39 00 00D0 04 EB 4E
+B +C +D +E +F
05 90 D4 00 07
1.2.
3.
4.5.6.7.8.
9.10.11.12.The unit will now have the correct DATA for the new MEMORY IC.
Enter DATA SET mode by setting VOLUME to minimum.While holding down VOLUME button on front cabinet, press key (6) on remote control for more than 2 seconds.ADDRESS and DATA should appear as FIG 1.ADDRESS is now selected and should "blink". Using the VOL. +/- button on the remote, step through the ADDRESS untilrequired ADDRESS to be changed is reached.Press ENTER to select DATA. When DATA is selected, it will "blink".Again, step through the DATA using VOL. +/- button until required DATA value has been selected.Pressing ENTER will take you back to ADDRESS for further selection if necessary.Repeat steps 3 to 6 until all data has been checked.When satisfied correct DATA has been entered, turn POWER off (return to STANDBY MODE) to finish DATA input.
After the data input, set to the initializing of shipping.Turn on the POWER.Set the VOLUME to minimum.While holding down VOLUME button on front cabinet, press key (1) on remote control for more than 2 seconds.After the finishing of the initializing of shipping, the unit will turn off automatically.
Set Key Remocon Key Operations
VOL. (-) MIN 1 Initialization of factory data.NOTE: Do not use this for normal servicing. If you set factory initialization, the memories are reset such as the clock
setting, the channel setting, the POWER ON total hours.
VOL. (-) MIN 6
POWER ON total hours is displayed on the screen.Refer to the "CONFIRMATION OF HOURS USED".
Can be checked of the INITIAL DATA of MEMORY IC.Refer to the "WHEN REPLACING EEPROM (MEMORY) IC".
VOL. (-) MIN Display of the Adjustment MENU on the screen.Refer to the "ELECTRICAL ADJUSTMENT" (On-Screen Display Adjustment).
9
VOL. (-) MIN 0 Releasing of V-CHIP PASSWORD.
NOTE: The each item value might be differentaccording to each set.
This unit is provided with the following SERVICE MODES so you can repair, examine and adjust easily.To enter the Service Mode, press both set key and remote control key for more than 2 seconds.
ELECTRICAL ADJUSTMENTS
1.
Read and perform these adjustments when repairing thecircuits or replacing electrical parts or PCB assemblies.
CAUTION
•
•
•
•
Use an isolation transformer when performing any serviceon this chassis.Before removing the anode cap, discharge electricitybecause it contains high voltage.When removing a PCB or related component, afterunfastening or changing a wire, be sure to put the wireback in its original position.When you exchange IC and Transistor for a heat sink,apply the silicon grease on the contractsection of the heat sink, Before applying new silicongrease, remove all the old silicon grease. (Old greasemay cause damages to the IC and Transistor.)
2. BASIC ADJUSTMENTSBEFORE MAKING ELECTRICALADJUSTMENTS 2-1: CUT OFF
1.
2.3.
4.
Adjust the unit to the following settings.R.DRIVE=10, B.DRIVE=10, R.BIAS=64, G.BIAS=64,B.BIAS=64, BRI.CENT=120, CONT.MAX=40.Place the set with Aging Test for more than 15 minutes.Activate the adjustment mode display of Fig. 1-1 andpress the channel button (01) on the remote control toselect "CUT OFF".Adjust the Screen Volume until a dim raster is obtained.
2-2: FOCUS
1.2.3.
Receive the monoscope pattern.Turn the Focus Volume fully counterclockwise once.Adjust the Focus Volume until picture is distinct.
2-3: WHITE BALANCE
NOTE: Adjust after performing CUT OFF adjustment.
Place the set with Aging Test for more than 10 minutes.Receive the white 100% signal from the PatternGenerator.Using the adjustment control, set the brightness andcontrast to normal position.Activate the adjustment mode display of Fig. 1-1 andpress the channel button (10) on the remote control toselect "R.BIAS".Using the VOL. UP/DOWN button on the remote control,adjust the R.BIAS.Press the CH. UP/DOWN button on the remote control toselect the "R.DRIVE", "B.DRIVE", "G.BIAS" or "B.BIAS".Using the VOL. UP/DOWN button on the remote control,adjust the R.DRIVE, B.DRIVE, G.BIAS or B.BIAS.Perform the above adjustments 6 and 7 until the whitecolor is achieved.
1.2.
3.
4.
5.
6.
7.
8.
1. Synchro Scope2. Digital Voltmeter
On-Screen Display Adjustment
In the condition of NO indication on the screen.Press the VOL. DOWN button on the set and theChannel button (9) on the remote control for more than1 second to appear the adjustment mode on thescreen as shown in Fig. 1-1 .
1.
Fig. 1-1
Use the Channel UP/DOWN button or Channel button(0-9) on the remote control to select the options shownin Fig. 1-2 .Press the MENU button on the remote control to endthe adjustments.
2.
3.
Prepare the following measurement tools for electricaladjustments.
FUNCTIONOSD HCUT OFFH.VCOH.PHASEV.SIZEV.SHIFTR.DRIVEB.DRIVER.BIASG.BIASB.BIASBRIGHT CENTBRIGHT MAXBRIGHT MIN
NO.0001040506070809101112131415
Fig. 1-2
FUNCTIONCONTRAST CENTCONTRAST MAXCONTRAST MINCOLOR CENTCOLOR MAXCOLOR MINTINTSHARPNESSFM LEVELSEPARATIONTEST MONOTEST STEREO
NO.161718192021222324272829
TV
00 OSD 23
2-4: SUB TINT/SUB COLOR
1.2.3.
4.
5.6.
7.
8.9.
Receive the color bar pattern. (RF Input)Connect the oscilloscope to TP023.Activate the adjustment mode display of Fig. 1-1 andpress the channel button (22) on the remote control toselect "TINT".Press the VOL. UP/DOWN button on the remote controluntil the section "A" becomes as straight line.(Refer to Fig. 2-1)Connect the oscilloscope to TP022.Activate the adjustment mode display of Fig. 1-1 andpress the channel button (19) on the remote control toselect "COL.CENT".Press the VOL. UP/DOWN button on the remote controluntil the red color level is adjusted to 110 ±10% of thewhite level. (Refer to Fig. 2-2)Receive the color bar pattern. (Audio Video Input)Press the TV/VIDEO button on the remote control to set to the AV mode. Then perform the above adjustments2~7.
D-1
ELECTRICAL ADJUSTMENTS
2-8: OSD HORIZONTAL
1.2.
Activate the adjustment mode display of Fig. 1-1 .Press the VOL. UP/DOWN button on the remotecontrol until the difference of A and B becomesminimum. (Refer to Fig. 2-3)
BA
TV
00 OSD 23
Fig. 2-3
Receive the monoscope pattern.(RF Input)Using the adjustment control, set the brightness andcontrast to normal position.Activate the adjustment mode display of Fig. 1-1 andpress the channel button (13) on the remote control toselect "BRI.CENT".Press the VOL.UP/DOWN button on the remote controluntil the screen begin to shine.Press the TV/VIDEO button on the remote to set to theAV mode. Then perform the above adjustment 2~4.
1.2.
3.
4.
5.
2-9: BRIGHT MANUAL
Fig. 2-1
Fig. 2-2
2-5: HORIZONTAL PHASE
1.2.
3.
4.
Receive the monoscope pattern.Using the adjustment control, set the brightness andcontrast to normal position.Activate the adjustment mode display of Fig. 1-1 andpress the channel button (05) on the remote control toselect "H.PHAS".Press the VOL. UP/DOWN button on the remotecontrol until the SHIFT quantity of the OVER SCAN onright and left becomes minimum.
2-6: VERTICAL SIZE
1.2.
3.
4.
Receive the monoscope Pattern.Using the adjustment control, set the brightness andcontrast to normal position.Activate the adjustment mode display of Fig. 1-1 andpress the channel button (06) on the remote control toselect "V.SIZE".Press the VOL. UP/DOWN button on the remote controluntil the SHIFT quantity of the OVER SCAN on upsideand downside becomes 10 ± 2%.
2-7: VERTICAL SHIFT
1.2.
3.
4.
Receive the monoscope Pattern.Using the adjustment control, set the brightness andcontrast to normal position.Activate the adjustment mode display of Fig. 1-1and press the channel button (07) on the remotecontrol to select "V.SFT".Press the VOL. UP/DOWN button on the remotecontrol until the horizontal line becomes fit to thenotch of the shadow mask.
White 100% Red 110%
"A"
Receive an 70dB the color bar pattern.Activate the adjustment mode display of Fig. 1-1press the channel button (17) on the remote controlto select "CONT.MAX".Press the VOL. UP/DOWN button on the remote controluntil the contrast step No. becomes "43".Press the TV/VIDEO button on the remote control to set to the AV mode.Activate the adiustment mode display of Fig 1-1paess the channel button (17) on the remote controlto select"CONT.MAX".Press the VOL.UP/DOWN button on the remote controlunitil the contrast step No. becomes "52".Receive a broadcast and check if the picture is normal.
1.2.
3.
4.
5.
6.
7.
2-10: SUB CONTRAST
Please check if the fixed values of each adjustmentitem is set correctly referring below. (RF/AV)
2-11: Confirmation of Fixed Value (step No.)
NO.041415161820
FUNCTIONH VCOBRIGHT MAXBRIGHT MINCONT CENTCONT MINCOLOR MAX
0414050251274
STEP NO. NO.212324272829
FUNCTIONCOLOR MINSHARPNESSFM LEVELSEPARATIONTEST MONOTEST STEREO
005300000000
STEP NO.
D-2
ELECTRICAL ADJUSTMENTS
3. PURITY AND CONVERGENCEADJUSTMENTS
NOTE
1.
2.
3.
Turn the unit on and let it warm up for at least 30minutes before performing the following adjustments.Place the CRT surface facing east or west to reduce theterrestrial magnetism.Turn ON the unit and demagnetize with a Degauss Coil.
3-1: STATIC CONVERGENCE (ROUGH ADJUSTMENT)
1.
2.
3.
4.
5.
6.
7.
8.
Tighten the screw for the magnet. Refer to the adjustedCRT for the position. (Refer to Fig. 3-1)If the deflection yoke and magnet are in one body,untighten the screw for the body.Receive the green raster pattern from the color bargenerator.Slide the deflection yoke until it touches the funnel sideof the CRT.Adjust center of screen to green, with red and blue onthe sides, using the pair of purity magnets.Switch the color bar generator from the green rasterpattern to the crosshatch pattern.Combine red and blue of the 3 color crosshatchpattern on the center of the screen by adjusting the pairof 4 pole magnets.Combine red/blue (magenta) and green by adjusting thepair of 6 pole magnets.Adjust the crosshatch pattern to change to white byrepeating steps 6 and 7.
3-2: PURITY
NOTE
Adjust after performing adjustments in section 3-1.
1.2.
3.
4.5.
Receive the green raster pattern from color bar generator.Adjust the pair of purity magnets to center the color on thescreen.Adjust the pair of purity magnets so the color at the endsare equally wide.Move the deflection yoke backward (to neck side)slowly, and stop it at the position when the whole screen isgreen.Confirm red and blue color.Adjust the slant of the deflection yoke while watching thescreen, then tighten the fixing screw.
DEFLECTION YOKEDEFLECTION YOKE SCREWMAGNET SCREW
PURITY MAGNETS6 POLE MAGNETS4 POLE MAGNETS
Fig. 3-1
3-3: STATIC CONVERGENCE
NOTE
Adjust after performing adjustments in section 3-2.
1.
2.
3.
Receive the crosshatch pattern from the color bargenerator.Combine red and blue of the 3 color crosshatchpattern on the center of the screen by adjusting the pairof 4 pole magnets.Combine red/blue (magenta) and green by adjusting thepair of 6 pole magnets.
3-4: DYNAMIC CONVERGENCE
NOTE
Adjust after performing adjustments in section 3-3.
1.
2.
Adjust the differences around the screen by moving thedeflection yoke upward/downward and right/left.(Refer to Fig. 3-2-a)Insert three wedges between the deflection yoke andCRT funnel to fix the deflection yoke.(Refer to Fig. 3-2-b)
R G B
RGB R
GB
R G B
UPWARD/DOWNWARD SLANT RIGHT/LEFT SLANT
Fig. 3-2-a
WEDGE WEDGE
WEDGE
WEDGE POSITION
Fig. 3-2-b
D-3
ELECTRICAL ADJUSTMENTS
4. ELECTRICAL ADJUSTMENT PARTS LOCATION GUIDE (WIRING CONNECTION)
CD101A
CP
802A
TU001
S501A
S501B
FB401
CD101B
AC
IN
CP401
CP802B
CP806
CP803B
CP801
R807
R803
SPEAKER
TP023
TP022
CRT PCB
TV MT PCB
GN
D C
RT
CD
801
DEGAUSS COIL
CP502
L503
CR
T DY
D-4
CP803A
J801
CD501
OSD
BLOCK DIAGRAM
78
70
69
68
67
RGB Proc.2OSD SWCONTRAST BRIGHTNESS
I/OIICTIMINT
PWMAD
MCUCLK
VCXO
RGB OUTPUT Stage DRIVE CUT OFF HV BLK
Ver.Proc.Ver SYNC SEPVer.COUNT DOWNV RAMP
Q801
RED OUT
Q802
GREEN OUT
Q803
BLUE OUT
Q402
H. DRIVE
Q401
H. OUTPUT
51
45
46
9
HV
F
S
FB401
10
1
2
3
CRTV801
3 9 7
RGB
Heater
F 84
PUMP UP
AMP+
-
7 52 6
V-OUT ICIC401 STV9302B
VCC
RGB Proc.1RGB MATRIXCOLOR CONT
ROMRAM
38375758 16
Hor.Proc.
SYNC SEPA/Hor. VCO
Hor.COUNT DOWN
AFC-1/H COINCIDENT
AFC-2 H PHASE
1 DY
Q507
FEED BACK
T501
4
8
13
Q502
POWER CTL
6
MEMORY ICIC199 BR24L02F-WE2
POWER
VOL. DOWN
CH. DOWN
VOL. UP
CH. UP
X6013.579545MHz
OS101
1
16
MICON/CHROMA IC IC101 OEC7091C
Chroma Proc.ACC/C-BPFAPC/KILLERTINT/DEMO
IC501PS2561AL1-1-V(W)
TU001
17
66
Q501
SWITCHING
D501~D504
RECTIFIER
Q506
RELAY DRIVE
5662
65
SDA SCL
Q607
H.CTL
50
52
E-1 E-2
FEED BACK SW
IC1001 AN7511
4 6SOUND AMP
IC2 8
SPEAKERSP1001
2
3 EAR PHONE JACKJ1001
1
AC IN
F501
L503
DE
GA
US
S C
OIL
TH
501
RY501
RELAY
13
12
11
10
2620
73
2721
ATT 34
2
J702
2
J703
76
Q105
SW
D106
Q602
Q606
R605D
604D603
C621 C
620_1
W803
C1003
IC1001
C1005
W813
W036W035
W043
D001
R602
W065
W067
C605
W058
R608
R621
R604
D606
R606
W060
C633 R616
R617
R109
Q601
Q603
W050
R615
R613R614
R611
C628
W063
R601
X601
C601C106
W053
W072
CP
802A
CD
101A CD
101B
J703 J702
TU
001
R002
SW101 SW102 SW103 SW104 SW105
R505
R449
R448
R413_1
W047
W048
C427 R416
D403
R415
R418R424C
414
J1001
R629
IC40
1
W030
W010
C437
R408
D412
D509
D508
HS
501
C508
TH501_1
C519
C446
C417
W006
W024
R814_1C810_1
R816
R809
R811
R813_1C808_1
R815
R504
TP024
TP023
TP022
TP401
R519
R509
D512
R429_2
FH
501
FH502
F501
S501B
R806
R802
L501
CP803B
L801_1
R805_
1
R80
3_1
R80
7_1
CP806
Q802
CP802B
S501A
C435
R518_1
R502D
515
W007
IC501
R515
R513
D528
R512
D516
R447
CP401
R507
CP803A
C403
R514
C410_1
R427
D501
HS
402
C509
R506
R503
Q502
Q501
R542
D503
D502
CP502
D408
D405
B504
B501
R51
7_1
D504
R422
D510
D513
D505
D506
R1007
D410
R410
AF
C
HS401
C123_1
OS
101
J801
CO
L
+B
8V
AB
L
GN
D
25V
12V180V
HE
AT
ER
R423
R538
W004
Q801
Q803
D411
C434
RY501
Q507
D517
W041
R417
C516
R525
Q503W061
C507
D514
R523
R527
R607
W046
D521
C622
W073
C610_1
W064
W062
C617
W816
W032
R405
C809_1
D404
W008
W009
D106_1
W031
Q105
R121
D522
R001
R445
W054
R1001 C1008
R130
W018
W817
W029
C103
C606 W017
W016
C118
Q401
W005
CP601
W055
W056
W057
W020
R110
R113
R112
W069
W070
C602
W015
W071
W049
W019
R421
C440
R446
R403
W038W037
W021
C448_1
C624
C630
D406
D409
W023
W002
R401
R409_1
W013
W011
C007_1
W027
W026
W025
R119
W003
R804
C406
T401
R620
R500
Q402
C518
T502
C422
C502
C503
C505
R501
C515
C514_1
C517_1
C418
C819_1
C443
W051
W040
W045
W834
R603
C623
W066
D602
W068
W033
R704_1
W812
C447
W001
W059
R510
R522
D511
C511
R539D518
W039
L001
W044
W052
W042
W028
R508
S802Y
S802X
CP503
FB401
W080
W034
C526_1C
521_1
CP
801
R402
L401
C401
CD
501
W833
W808
W830
W811
W809
W819
D611
R537_1
W827
W832
W810
PRINTED CIRCUIT BOARDSTV MT/CRT (INSERTED PARTS)
SOLDER SIDE
F-1 F-2
CM
F081B
CC
F073B
RIS
KO
FF
IRE
-R
EP
LA
CE
AS
MA
RK
ED.
SE
RV
ICE
FO
RIN
FO
RM
AT
ION
AB
OU
TCR
ITIC
AL
CO
MP
ON
EN
TS
SE
EIN
SID
EB
AC
KC
OV
ER
.
CA
UT
ION
,
ATTENTIONINFORMATIONPOURSERVICEDESPIECECRITIQUE VOIR AUVERSO.,
1
25
41
64
C10
04
R10
03
R00
4R
003
R61
0
C10
1
C60
9
R61
8
C11
2C
629
C62
6C
627
C60
4
C10
4
C10
2
IC10
1
R702
R70
3
R128
R12
6
R101
R14
3_1
R10
08
R420
R41
9C50
1
R532
R53
1
C60
3
R10
4
C10
8_1
C10
7
C10
5
R10
2
R10
3
R12
5
R609
R11
5
C00
1
R10
05
R10
04
R12
7
R11
6_1
R627
R12
4R
106_
1
R105_1
R10
7
R108
R129
IC199
C10
01
Q505
Q607
Q506
C51
0
R51
6_1
C61
2C
614
R70
1
C61
6C
615
R13
4_1
C51
3_1
C00
4_1
PRINTED CIRCUIT BOARDSTV MT (CHIP MOUNTED PARTS)
SOLDER SIDE
F-3 F-4
CM
F08
1B
CC
F07
3B
A B C D E F G H
A B C D E F G H
2
1
3
4
5
6
7
8
2
1
3
4
5
6
7
8
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED
C629
0.01 B
C001
0.01 F
C62
7
0.01
BC
626
0.01
B
C10
8_1
0.00
1B
C615
1 B
C616
1 B
C620_1
0.01 B
C11
2
100P
CH
C00
7_1
0.02
2F
C00
4_1
0.02
2B
C10
4
0.01
B
C102
0.01 B
C62
4
1TF
C10
547
0PB
C10
722
0PB
C60
2
0.1
F
C60
3
22P
CH
C101
0.01 B
C60
40.
022
F
C612
1 B
C614
1 B
C609
0.01 B
C12
3_1
1050
VYK
C63
3
1050
VYK
C62
8
150
VKA
C60
5
150
VKA
C10
61
50V
KA
C60
6
100
10V
YK
C617
10010V YK
C60
1
150
VKA
C622
150V KA
C10
3
470
6.3V
YK
C623
2.250V KA
C630
47010V YK
C621
4716V YK
C118
4706.3V YK
C610_1
4716V YK
R61
7
47K
1/4W
R61
6
1K1/
4W
R110
10K 1/4W R109
10K 1/4W
R60
9
120KR
613
100
1/4W
R61
410
01/
4W
R61
510
01/
4W
R13
4_1
4.7K
R60
1
8.2K
1/4W
R10
5_1
4.7K
R60
2
100
1/4W
R10
2
1K
R618
22K
R003
100
R62
0
1K1/
2W
R605
220 1/2W
R130
10K 1/4W R10
7
100
R124
10K
R143_1
10
R61
1
10K
1/4W
R002
15K 1/2W
R001
15K 1/2W
R116_1 2.2KR
106_
1
4.7K
R606
22K 1/4W
R61
0
12K
R607
100 1/4W
R126
2.7K
R101
560
R621
220 1/4W
R608
680 1/4W
R604
100 1/4W
R10
4
1M
R128
560
R127
1K
R62
7
10KR
108
100
R125
47K
R129
47K
R119
22K 1/4W
R10
31K
R112 2.2K 1/4W
R113 2.2K 1/4W
R115 22K
R12
1
270
1/4W
R004
100
R603
120 1/2W
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICENOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
DANS LA NOMENCLATURE DES PIECESN’UTILISER QUE CELLS DECRITESDANGEREUSES AN POINT DE VUE SECURITE
:LES PIECES REPAREES PAR UN ETANTATTENTION:SINCE THESE PARTS MARKED BYCAUTIONDESCRIBED IN PARTS LIST ONLYCRITICAL FOR SAFETY,USE ONES
ARE
W83
3
W80
9
W80
8
W81
6
IC19
9BR
24L0
2F-W
E2
MEM
OR
Y IC
1 2 3 4
5678
D611
MTZJ12B
D602
MTZJ9.1B
D604
MTZJ8.2B
D00
1
MTZ
J33B
D603
1SS133
D60
611
E1-E
IC
Q602KTC3203_Y
5V REG
Q603KTC3203_Y
5V REG
Q601KTC3203_Y
5V REG
Q606KTC3203_Y
8V REG
Q607KTC3875S-GR-RTK/P
H.CTL
R629
22 3W
CAUTION: DIGITAL TRANSISTOR
IC101OEC7091C
MICON/CHROMA IC
1 10 11 12 13 14 15 16 17 18 192 20 21 22 23 24
2526
2728
29
3
3031
3233
3435
3637
3839
4
40
414243444546474849
5
50515253545556575859
6
6061626364
6566
6768
69
7
7071
7273
7475
7677
7879
8
80
9
SW10
4EV
Q21
505R
VOL
DO
WN
SW10
3EV
Q21
505R
VOL
UP
SW10
2EV
Q21
505R
CH
DO
WN
SW10
1EV
Q21
505R
CH
UP
SW10
5EV
Q21
505R
POW
ER
X601
100B
T3R
537
3.57
9545
MH
z
CP601 A2001WR2-6P
1
2
3
4
5
6
L001
3.3uH 0305
Q105KRA102MAT
SWITCHING
TU001115-V-KA35ARH
1
10
11
12
13
14
15
16
17
1819
2
20 21
3
4
5
6
7
8
9
D10
6_1
SLR
-342
VCT3
2
POW
ER O
N/O
N T
IMER
S802X
S802Y
GN
D
B+
Vout O
S101
KSM
-713
SY
123
P.C
ON
+5V
P.C
ON
+5V
H_O
UT
H_C
TL
ABC
L
CLAMP
H_C
TL
G.O
UT
R.O
UT
H_S
YNC
B.O
UT
DEG
AUSS
_H
PRO
TEC
T
P.CON+B
V_OUT
GND
V_FEEDBACKAT+5VABCL
H_OUT
X-RAYSDA
R.OUT
G.OUTSCL
B.OUT
H_SYNC
AFTUNREG+12V
KEY1 V_OUTPOWER_FAIL
UNREG+12VKEY2 V_FEEDBACK
X-RAYGNDPOWER_ON
DEGAUSS_HREMOCON
AT+5V
AUDIO_OUT
AUDIO_MUTE
X-RAY
AUDIO_MUTEP.CON+5VIIC_OFF VIDEO_INTUNER+5V
AUDIO_INON_TIMERAUDIO_OUT
P.CON+5V
GNDPOWER_FAIL AUDIO_IN
VIDEO_IN
TUNER+5V
AT+5V
TU_VIDEO
TU_AUDIO
ON_TIMER
SCL
KEY1
KEY2
REM
OC
ON
AT+5
V
POW
ER_O
N
SDA
AFTIIC_OFF
TU_AUDIO SDA
SCL
P.CON+B
TU_VIDEO2.9
32
3.3
4.95
4.93
4.94
(TV MT PCB)
TEST POINT
SCL
SDA
IIC_OFF
GND
NC
NC
FROM/TO TV POWER
G-2G-1
MICON/CHROMA/TUNER SCHEMATIC DIAGRAM
FROM/TO SOUND/AV
FROM/TO DEFLECTION/CRT
PCB070CMF081
3
4.9
7.25.5
5.57.2
4.9
4.900000
4.90
NC
NC
NC
NC
NC
NC
8.8
5.54.9
8.5
Ver SYNC SEPVer.COUNT DOWNV RAMP
Ver.Proc.Hor.Proc.SYNC SEPA/Hor.VCOHor.COUNT DOWNAFC-1/H COINCIDENTAFC-2 H PHASE
PGB OUTPUT StageDRIVECUT-OFFHV BLK
IIC BUSDECODER
OSDROMRAM
CCD
CPU core
VCOXO
COLOR CONTRGB MATRIXRGB Proc.1
RGB Proc.2OSD SWCONTRASTBRIGHTNESS
MCU RESETPower Manage.
MCUCLK Y MUTE
BLACK STRETCH
Vldeo Proc.C-TRAP/YDELAYSHARPNESS
Chroma Proc.ACC/C-BPFAPC/KILLERTINT/DEMO
ATT
VCXO
LPF6bB AMP
MCU GND
IIC
TIM
AD
PWM
INT
I/O
CLK CONT
P-ON CONT
SDA/SCL
NC
NC
4.8
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
5.6
NC NC
0 0 5.0 5.0 0 4.9 0 1.2 2.0 0.8 3.4 4.9 5.0 3.4 0 3.4 2.9 5.6NC
2.82.90 5.0 0 2.0
2.2
2.0
8.8
4.6
2.3
4.5
0
2.6
5.7
2.3
3.3
4.0
4.6
3.1
8.8
2.0
03.73.404.94.68.008.03.53.23.22.34.604.90.3
2.4
4.9
4.9
4.9
4.9
4.9
4.9
2.9
4.9
0
4.9
0
0
4.9
4.9
7.9
11.3
2
5 6 7
4
1
4.9 5
5.1
VSS
E2E1E0VC
C
MO
DE
SDA
SCL
4.9 4.9 4.9
0 0 0 0
0
4.8
0
0
A B C D E F G H
A B C D E F G H
2
1
3
4
5
6
7
8
2
1
3
4
5
6
7
8
C51
5
1000
16V
YK
C51
6
150
VYK
C51
9
1000
16V
YK
C52
1_1
220
200V
YXF
CP5
0300
3P-2
100
1
CP502A1561WV2-2P
1
2
HS501763WSAA029
R51
8_1
5.6K
+-1%
R514
0.22 1W
S501
A
S501
B
IS NON POLAR ONE.THE ALUMI ELECTROLYTIC CAPACITOR MARKED NPTHE RESISTOR MARKED F IS FUSE RESISTOR.NOTE:
Q505KTA1504S-GR-RTK/P
P.FAIL
Q5032SA1624
PROTECT DRIVE
R501
3.3 5W C
L501ELF15N010AP
COIL,LINE FILTER
1 2
3 4
21
L503DYD1-3020-80
DEGAUSS COIL
FH502EYF-52BCY
FH501EYF-52BCY
F5014A125V
4A125V
IC501PS2561AL1-1-V(W)
FEED BACK
123
4
B501
W5R
H3.
5X5X
1.0
B504
W5RH3.5X5X1.0
TH501_1
B59203-S1060-B14
4A 125V
4A 125VTYPE 4A 125V (F501).D’INCEIE N’UTILISER QUE DES FUSIBLE DE MEME
:POUR UNE PROTECTION CONTINUE LES RISQUESATTENTIONFUSE.REPLACE ONLY WITH THE SAME TYPE 4A 125V (F501)
CAUTION:FOR CONTINUED PROTECTION AGAINST FIRE HAZARD,
S
DG
Q50
12S
K356
3(O
RIO
N_Q
)
POW
ER A
MP
BLACK
WHITE
BLAD
EW
IDE
CD501P201-2469-2
AC120V_60Hz
RY501
ALKS321
1 2
34
T50281291084
11
12
13
14
15
16
17
18
2
3
4
5
6
7
8
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED
C50
2
0.00
150
0VB
C50
1
0.00
82B
C51
4_1
820P
2KV
RR
C518
470P500V B
C509
0.047 M
C517_1
820P2KV RR
C51
3_1
0.00
1B
C50
3
0.00
150
0VB
C50
5
0.1
275V
ECQ
UL
C508
0.0047250V KXC510
0.1 B
C511
150V KA
C52
6_1
220
200V
YK
C50
7
1010
0VM
HE
R51
0
1.2M
1/2W
R51
5
120K
1/2W
R537_1
22K 1/2W
R50
6
1K1/
4W
R50
3
100
1/4W
R527
5.6K 1/4W
R52
2
1.2M
1/2W
R51
6_1
10K
R504
100 1/4W
R50
0
2.7M
1/2W
+-10
%
R523
47K 1/4W
R53
8
1.5M
1/2W
R532
10K
R53
1
10K
R50
9
220
1/4W
R50
2
1K1/
4W
R505
1.2K 1/4WR
539
101/
4W
R508
220 1/2W
R512
680 1/4WR
513
2.2K
1/4W
R519
1.2K 1/4W
R50
7
271/
4W
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICENOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
DANS LA NOMENCLATURE DES PIECESN’UTILISER QUE CELLS DECRITESDANGEREUSES AN POINT DE VUE SECURITE
:LES PIECES REPAREES PAR UN ETANTATTENTION :SINCE THESE PARTS MARKED BYCAUTIONDESCRIBED IN PARTS LIST ONLYCRITICAL FOR SAFETY,USE ONES
ARE
W834
W83
2
W81
0
W82
7
W81
9
W83
0
D50
6
MTZ
J18B
D50
9
MTZ
J18B
D521
MTZJ12B
D52
8
MTZ
J5.6
B
D517
1SS133
D50
3
1N40
05-E
IC
D51
8
1SS1
33
D52
2
1SS1
33
D51
4
1SS1
33
D505
21DQ09N
D50
1
1N40
05-E
IC
D51
2
1SS1
33
D516
1N4937
D513
21DQ09N
D51
5
1SS1
33
D50
4
1N40
05-E
IC
D510
RU2AM-EIC
D50
2
1N40
05-E
IC
D50
8
1SS1
33
D51
1
1SS1
33
Q502KTC3198
POWER CTL
Q506KTC3875S-GR-RTK/P
RELAY DRIVE
Q507KTC3198
FEED BACKSWITCHING
R54
2
0.68
1W
R525
1.5 2W
R517_1
1 1W
GND
SOUND+B
SOUND_GND
+BUNREG+12V
P.CON+B
GND
POWER_FAIL
DEGAUSS_H
X-RAY
UNREG+12V
AT+5V
GND
(TV MT PCB)
0
0
10.3
TV POWER SCHEMATIC DIAGRAM
FROM/TO DEFLECTION/CRT
TO SOUND/AV
144.0
NC
NC
0
0
1.7
NC 0
132.3
11.3
NC
144.0
10.3
6.6
10.3
10.0
0.1
0
4.8
0.1
4.8
4.9 0
4.8
135.0 0
135.0
FROM/TO MICON/CHROMA/TUNER
9.50.1
10.511.5
9.5
5.5
6.0
PCB070CMF081
G-4G-3
A B C D E F G H
A B C D E F G H
2
1
3
4
5
6
7
8
2
1
3
4
5
6
7
8
TP024TP022 TP023
TP401
CP401A1561WV2-A5P
1
2
3
4
5
IC401 STV9302BV-OUT IC
1 2 3 4 5 6 7
T401STP-03Q24
1
2
3 4
6
BGR
1168
109
175
V801A34AGT13X98(DL)
F
J801ISMP01S
1
345
67
8 9
Q4012SC5885
H.OUTPUTVIDEO
8
E8E25
E12
GND
TERHEAAFC
B+
GND
ABL
GND
COLHV
F
S
FB401 FNI14B002_M
1
10
11
2
3
4
5
6
7
8
9
L801
_1
100u
H06
06
CP803B B2013H02-4P
1
2
3
4
CP803A B2013H02-4P
1
2
3
4
CP802AB2013H02-5P
1
2
3
4
5
CP802BB2013H02-5P
1
2
3
4
5
C42
7 1050
VYKC41
7 2250
VYK
CP801131001101K1
1
HS402763WSA0043
HS401763WSAA029
R409_1
27K 1/4W +-1%
R40
8
10K
+-1%
R40
2
681/
2W
CP806
IS NON POLAR ONE.THE ALUMI ELECTROLYTIC CAPACITOR MARKED NPTHE RESISTOR MARKED F IS FUSE RESISTOR.NOTE:
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED
C80
8_1
470P
CH
C81
0_1
470P
CH
C80
9_1
470P
CH
C43
7
0.47
250V
PMS
C41
0_1
0.00
1C
H
C42
2 0.15
100V
MKT
C81
9_1
0.00
12K
VB
C44
0
0.01
100V
MM
TS
C406
220P500V B
C44
3
0.00
911.
25KV
PHE
C40
3
470
35V
YK
C43
5 0.1
100V M
HE
C44
8_1 22
250V YK
C41
8
470
25V
YK
C41
4
100
35V YK
C43
4
2210
0VYK
C44
6
2250
VYK
C44
7
150
VYK
C40
1
125
0VM
HE
R80
9
2.7K
1/4W
R424
470 1/4W
R445
180K 1/4W
R42
1
220K
1/4W
R448
560 1/2W
R449
560 1/2W
R418
22K 1/4W
R41
3_1
2.2K
1/2W
R41
0
330
1/2W
R415
1.8K 1/2W
R41
6
11/
2W
R81
6
270
1/4W
R81
4_1
2.7K
1/4W
R81
3_1
270
1/4W
R420
2.7K
R81
5
270
1/4W
R80
6
2.7K
1/4W
R42
2
2.2
1/2W
R41
9
470
R41
7
10K
1/4W
R44
6
470
1/2W
R423
100 1/4W
R80
2
2.7K
1/4W
R80
4
2.7K
1/4W
R81
1
2.7K
1/4W
R403
10K 1/4W
R42
7
100
1/4W
R40
5
1K1/
4W
R401
27K M+-1%
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICENOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
DANS LA NOMENCLATURE DES PIECESN’UTILISER QUE CELLS DECRITESDANGEREUSES AN POINT DE VUE SECURITE
:LES PIECES REPAREES PAR UN ETANTATTENTION
:SINCE THESE PARTS MARKED BYCAUTIONDESCRIBED IN PARTS LIST ONLYCRITICAL FOR SAFETY,USE ONES
ARE
W817
D40
4
MTZ
J6.2
B
D41
2
MTZ
J5.1
B
D40
5
AU02
A-EI
C
D41
0
AU02
A-EI
C
D40
9
11E1
-EIC
D40
8
11E1
-EIC
D406
11E1-EIC
D411
AU02A-EIC
D403
11E1-EIC
Q4022SC1627_Y
H.DRIVE
Q8012SC1473A
RED OUTQ802
2SC1473A
GREEN OUTQ803
2SC1473A
BLUE OUT
R447
150 2W
R80
7_1
15K
1W
R429_2
4.7 3W
R80
3_1
15K
1W
R80
5_1
15K
1W
L401
4.7m
H
GND GND
CLAMP CLAMP CLAMP
G.OUT G.OUT G.OUT
R.OUT R.OUT R.OUT
B.OUT B.OUT B.OUT
HEATER HEATER
GND GND
180V 180V
X-RAY
P.CON+B
GND
V_FEEDBACK
V_OUT
ABCL
H_OUT
H_SYNC
GND
+B
P.CON+B
UNREG+12V
(TV MT PCB)DEFLECTION/CRT SCHEMATIC DIAGRAM
G-5 G-6
FROM/TO TV POWER
PCB070CMF081
CCF073
96.4
9
NC
NC
NC
SCREEN
FOCUS
FOCUS
SCREEN
130.0
00
0
27.0
0.3
3.2
2.7
100.6
3.2
2.7
98.4
3.2
2.7
95.4
3.5 2.0 12.0 25.0 3.5
0
025.0
4.3
TO DY
NC
00
0
101.6
6.4 99.6
AMP
THERMALPROTECTION
PUMPUP NC NC
GND GND
CLAMP CLAMP
G.OUT G.OUT
R.OUT R.OUT
B.OUT B.OUT
HEATER
GND
NC
180V
PCB110
FROM/TO MICON//CHROMA/TUNER
FROM MICON/CHROMA/TUNER
HEATER
GND
NC
180V
14 15 16
13
12
8
10
11130.0
132.5
132.5
48.0
7.0
0
25.0
0
A B C D E F G H
A B C D E F G H
2
1
3
4
5
6
7
8
2
1
3
4
5
6
7
8
SPEAKER
SP1001S08F778 OHM
J1001MSJ-035-12A_PC
EAR PHONE_JACK
1
2
3
H E
J703AV1-09AD-4
RCA JACK WHITE
12H E
J702AV1-09AD-3
RCA JACK YELLOW
12
TM101RC-EH050(CT-859)
BT001MNAAA(R03)
UM-4
BT002
MNAAA(R03)
UM-4
C10
03 150
VKA
CD101BCH012007
CD101ACH012006
WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED
C10
04
0.00
15B
C1001
0.1 B
C10
08
4716
VYK
C10
05 1050
VYK
R704_1
10 1/4W
R703
820
R70
1
68 R70
2
47K
R1001
47K 1/4W
R1003
68K
R10
05
270K
R10
04
100K
R10
08
68K
R1007
68 1/2W
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICENOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
DANS LA NOMENCLATURE DES PIECESN’UTILISER QUE CELLS DECRITESDANGEREUSES AN POINT DE VUE SECURITE
:LES PIECES REPAREES PAR UN ETANTATTENTION :SINCE THESE PARTS MARKED BYCAUTIONDESCRIBED IN PARTS LIST ONLYCRITICAL FOR SAFETY,USE ONES
ARE
W80
3
W811
W81
2
W81
3
IC10
01AN
7511
SOU
ND
AM
P IC
1234
5 6 7 8
AUDIO_IN
VIDEO_IN
GND
SOUND_GND
SOUND+B
GND
AUDIO_MUTE
P.CON+5V
GND
AUDIO_OUT
(TV MT PCB)
FROM MICON/CHROMA/TUNER
FROM TV POWER
TO MICON/CHROMA/TUNER
VIDEO 2
AUDIO 219
20
ACCESSORY
-+
0
08.2 3.5 3.4
3.95.1 0.3
11
22
17
18
G-8G-7
SOUND/AV SCHEMATIC DIAGRAM
PCB070CMF081
WAVEFORMS
H-1
6 1V 20µs/div
NOTE: The following waveforms were measured at the point of the correspondingballoon number in the schematic diagram.
MICON/CHROMA/TUNER
1 0.5V 2ms/div 200V 20µs/div11
1V 20µs/div72 20V 20µs/div
DEFLECTION/CRT
10V 5ms/div12
3 200mV 20µs/div 8 0.5V 5ms/div 10V 5ms/div13
0.5V 5ms/div4 9 20V 20µs/div 50V 20µs/div14
10 2V 20µs/div5 1V 20µs/div 15 50V 20µs/div
WAVEFORMS
H-2
16 50V 20µs/div
NOTE: The following waveforms were measured at the point of the correspondingballoon number in the schematic diagram.
SOUND/AV
0.5V 1ms/div17
1V 1ms/div18
200mV 500µs/div19
20 500mV 20µs/div
MECHANICAL EXPLODED VIEW
202
102
107
202
202
202
202
104
101
101C
101B204
109
206
101A
101D
106
PCB110(CRT PCB ASS'Y)
I-1
PCB070(TV MT PCB ASS'Y)
205
103
205
203
106
106
201
201
201108 201
119
119
105
105
105
105
MECHANICAL EXPLODED VIEW(PACKING DIAGRAM)
116, 117, 118, TM101
113
113
113
115
111
110
114
114
114
114
110
110
112
I-2
MECHANICAL REPLACEMENT PARTS LIST
Location No. TSB P/N Reference No. Description
101 72781144 7A701A312A FRONT CABI ASS'Y 101A 72799312 701WPJC918 CABINET FRONT 101B 72799477 713WPAA203 GLASS LED 101C 72799476 713WPAA202 GUIDE REMOCON 101D 72799757 735WPBB315 BUTTON FRAME
102 75007550 702WPAA852 CABINET BACK 103 72794734 899HV3T000 HOLDER ANODE WIRE 104 72799717 726000A091 SHEET CRT SERVICEMAN 105 72796255 800WR0A011 SHEET CRT SUPPORT (D) 106 72798769 800WQ0A024 FELT SHEET 107 75007551 722549A709 SHEET RATING 108 72795687 741WUA0021 SPRING EARTH 109 72799738 735WPAA837 SPEAKER HOLDER
110 72783505 723000D248 SHEET BARCODE 111 72799981 791WHAA122 FILM BAG 112 72782852 791WHAA137 LIGHTRON SHEET 113 72798721 792WHAA052 PACKAGE TOP 114 72782855 792WHAA179 PACKAGE BOTTOM 115 75007552 793WCDD496 GIFT BOX 116 72783478 JB5ND200 POLYBAG INSTRUCTION(RED CAUTION) 117 75004935 J3X30302B GUARANTEE CARD 118 75007553 J3X00321A INSTRUCTION BOOK(E/S) 119 72799965 769WSAA011 WASHER CRT T=1
201 72781281 8121J50B5U SCREW TAP TITE(P) GW20 5*28 CH HEXAGON 202 72781279 8117540A6U SCREW TAPPING(B0) TRUSS 4*16 CH 203 72798786 810763080U SCREW TAP TITE(S) BRAZIER 3*8 CH 204 72798790 811063080U SCREW TAP TITE(P) BRAZIER 3*8 CH 205 72781255 8109I3080U SCREW TAP TITE(B) WH7 3*8 CH 206 72798791 8110630A0U SCREW TAP TITE(P) BRAZIER 3*10 CH
J1-1
ELECTRICAL REPLACEMENT PARTS LISTLocation No. TSB P/N Reference No. Description
RESISTORS ! R401 72794595 R4X5T6273F R,METAL 27K OHM 1/6W ! R408 72796016 R4X5T6103F R,METAL 10K OHM 1/6W ! R409 72781720 R4K1T4273F R,METAL 27K OHM 1/4W ! R429 72781702 R3K58B4R7J R,METAL OXIDE 4.7 OHM 3W ! R447 72781689 R3K58A151J R,METAL OXIDE 150 OHM 2W ! R500 72794631 R0G3K2275K RC 2.7M OHM 1/2W ! R501 72795522 R5X2CD3R3J R,CEMENT 3.3 OHM 5W ! R514 72794633 R63881R22J R,FUSE 0.22 OHM 1W ! R517 72781671 R3K581010J R,METAL OXIDE 1 OHM 1W ! R518 72795514 R4X5T6562F R,METAL 5.6K OHM 1/6W ! R525 72781692 R3K58A1R5J R,METAL OXIDE 1.5 OHM 2W ! R538 72795500 R002T2155J RC 1.5M OHM 1/2W ! R542 72781685 R3K581R68J R,METAL OXIDE 0.68 OHM 1W ! R629 72781701 R3K58B220J R,METAL OXIDE 22 OHM 3W ! R803 72781674 R3K581153J R,METAL OXIDE 15K OHM 1W ! R805 72781674 R3K581153J R,METAL OXIDE 15K OHM 1W ! R807 72781674 R3K581153J R,METAL OXIDE 15K OHM 1W
CAPACITORS ! C418 72795628 E02LT3471M CE 470 UF 25V ! C434 72794396 E02LU8220M CE 22 UF 100V C437 72795104 P4J7F3474J CMPP 0.47 UF 250V PMS ! C443 72783441 P4G8FJ912H CMPP 0.0091UF 1.25KV PHE ! C447 72794416 E02LU5010M CE 1 UF 50V C448 72796351 E02LTD220M CE 22 UF 250V ! C502 72795629 C0JTB0513K CC 0.001 UF 500V B ! C503 72795629 C0JTB0513K CC 0.001 UF 500V B ! C505 72795567 P2122B104M CMP 0.1 UF 275V ECQUL ! C508 72795579 CD39E0MQ3M CC 0.0047UF 250V ! C514 72795580 C0PLRR7W2K CC 820 PF 2KV RR ! C515 72794425 E02LT2102M CE 1000 UF 16V ! C517 72795580 C0PLRR7W2K CC 820 PF 2KV RR ! C518 72796329 C0JTB05Q2K CC 470 PF 500V B ! C519 72794425 E02LT2102M CE 1000 UF 16V ! C521 72794411 E62NFC221M CE 220 UF 200V ! C526 72797379 E02LFC221M CE 220 UF 200V C819 72795578 C0JBB0713K CC 0.001 UF 2KV B
DIODES D001 72794465 D97U03301B DIODE,ZENER MTZJ33B T-77 D106 72795529 0021721150 LED SLR-342VCT32 D403 72794488 D2WT011E10 DIODE SILICON 11E1-EIC D404 72794490 D97U06R21B DIODE,ZENER MTZJ6.2B T-77 ! D405 72794472 D2WTAU02A0 DIODE SILICON AU02A-EIC D406 72794488 D2WT011E10 DIODE SILICON 11E1-EIC D408 72794488 D2WT011E10 DIODE SILICON 11E1-EIC D409 72794488 D2WT011E10 DIODE SILICON 11E1-EIC ! D410 72794472 D2WTAU02A0 DIODE SILICON AU02A-EIC ! D411 72794472 D2WTAU02A0 DIODE SILICON AU02A-EIC ! D412 72794469 D97U05R11B DIODE,ZENER MTZJ5.1B T-77 ! D501 72795626 D2WXN40050 DIODE SILICON 1N4005-EIC ! D502 72795626 D2WXN40050 DIODE SILICON 1N4005-EIC ! D503 72795626 D2WXN40050 DIODE SILICON 1N4005-EIC ! D504 72795626 D2WXN40050 DIODE SILICON 1N4005-EIC ! D505 72794480 D28T21DQN9 DIODE SCHOTTKY 21DQ09N-TA2B1 D506 72795541 D97U01801B DIODE,ZENER MTZJ18B T-77 D508 72794491 D1VT001330 DIODE,SILICON 1SS133T-77 ! D509 72795541 D97U01801B DIODE,ZENER MTZJ18B T-77 ! D510 72795545 D2WXRU2AM0 DIODE SILICON RU2AM-EIC D511 72794491 D1VT001330 DIODE,SILICON 1SS133T-77 ! D512 72794491 D1VT001330 DIODE,SILICON 1SS133T-77 ! D513 72794480 D28T21DQN9 DIODE SCHOTTKY 21DQ09N-TA2B1 D514 72794491 D1VT001330 DIODE,SILICON 1SS133T-77 D515 72794491 D1VT001330 DIODE,SILICON 1SS133T-77 ! D516 72794483 D2WXN49370 DIODE SILICON 1N4937 D517 72794491 D1VT001330 DIODE,SILICON 1SS133T-77 D518 72794491 D1VT001330 DIODE,SILICON 1SS133T-77 D521 72794487 D97U01201B DIODE,ZENER MTZJ12B T-77 D522 72794491 D1VT001330 DIODE,SILICON 1SS133T-77 D528 72794489 D97U05R61B DIODE,ZENER MTZJ5.6B T-77 D602 72794481 D97U09R11B DIODE,ZENER MTZJ9.1B T-77 D603 72794491 D1VT001330 DIODE,SILICON 1SS133T-77 D604 72794486 D97U08R21B DIODE,ZENER MTZJ8.2B T-77 D606 72794488 D2WT011E10 DIODE SILICON 11E1-EIC D611 72794487 D97U01201B DIODE,ZENER MTZJ12B T-77
ICS IC101 72795532 I56F07091C IC OEC7091C IC199 75007546 S3X001VE03 MEMORY DATA BR24L02F-WE2 ! IC401 72783444 I0WTD9302B IC STV9302B ! IC501 72794512 000220002W PHOTO COUPLER PS2561AL1-1-V(W) ! IC1001 72795537 I01DP75110 IC AN7511
TRANSISTORS Q105 72795555 TPATB03003 COMPOUND TRANSISTOR KRA102MAT
J2-1
ELECTRICAL REPLACEMENT PARTS LISTLocation No. TSB P/N Reference No. Description
TRANSISTORS ! Q401 72795478 TC1G058850 TRANSISTOR SILICON 2SC5885 ! Q402 72795480 TC5T01627Y TRANSISTOR SILICON 2SC1627_Y(TPE2) ! Q501 72795539 T25F035630 FET 2SK3563(ORION_Q) ! Q502 72794577 TCATC31980 TRANSISTOR,SILICON KTC3198-AT(Y,GR) ! Q503 72794569 TA3T016240 TRANSISTOR,SILICON 2SA1624-AA Q505 75007547 T6AJ1504S0 TRANSISTOR SILICON KTA1504S-GR-RTK/P Q506 75007548 T8AJ3875S0 TRANSISTOR SILICON KTC3875S-GR-RTK/P Q507 72794577 TCATC31980 TRANSISTOR,SILICON KTC3198-AT(Y,GR) Q601 72795476 TCAT032034 TRANSISTOR, SILICON KTC3203_Y-AT Q602 72795476 TCAT032034 TRANSISTOR, SILICON KTC3203_Y-AT Q603 72795476 TCAT032034 TRANSISTOR, SILICON KTC3203_Y-AT Q606 72795476 TCAT032034 TRANSISTOR, SILICON KTC3203_Y-AT Q607 75007548 T8AJ3875S0 TRANSISTOR SILICON KTC3875S-GR-RTK/P ! Q801 72798340 TCKT1473A0 TRANSISTOR SILICON 2SC1473A-TA-(RQ) ! Q802 72798340 TCKT1473A0 TRANSISTOR SILICON 2SC1473A-TA-(RQ) ! Q803 72798340 TCKT1473A0 TRANSISTOR SILICON 2SC1473A-TA-(RQ)
COILS &TRANSFORMERS L001 72796518 02167F3R3J COIL 3.3 UH L401 72795560 021L75472J COIL 4.7 MH ! L501 72798941 0293000130 COIL,LINE FILTER ELF15N010AP ! L503 72798932 028B140033 COIL,DEGAUSS DYD1-3020-80 L801 72795941 021673101K COIL 100 UH T401 72796466 045011001L TRANS,HORIZONTAL DRIVE STP-03Q24 ! T502 72796474 0481291084 TRANSFORMER,SWITCHING 81291084
JACKS J702 72795495 060Q401112 RCA JACK AV1-09AD-3 J703 72795494 060Q401111 RCA JACK AV1-09AD-4 ! J801 72783271 066F120020 SOCKET,CATHODE RAY TUBE ISMP01S ! J1001 72796730 060J121014 JACK,RCA,3.5 MSJ-035-12A_PC
SWITCHES SW101 72794688 0504101T34 SWITCH,TACT EVQ21505R SW102 72794688 0504101T34 SWITCH,TACT EVQ21505R SW103 72794688 0504101T34 SWITCH,TACT EVQ21505R SW104 72794688 0504101T34 SWITCH,TACT EVQ21505R SW105 72794688 0504101T34 SWITCH,TACT EVQ21505R
P.C.BOARD ASSEMBLIES PCB070 75007549 A3X003V070L TV MT PCB ASS'Y CMF081B PCB110 72783447 A3X001V110L CRT PCB ASS'Y CCF073B
MISCELLANEOUS B501 72794357 024HT03553 CORE,BEADS W5RH3.5X5X1.0 B504 72794357 024HT03553 CORE,BEADS W5RH3.5X5X1.0 BT001 72783174 141U004016 BATTERY,MANGAN MNAAA(R03) BT002 72783174 141U004016 BATTERY,MANGAN MNAAA(R03) ! CD501 75005151 120Q414913 CORD AC BUSH P201-2469-2 ! CP401 72796822 069S450089 CONNECTOR PCB SIDE A1561WV2-A5P ! CP502 72796821 069S420110 CONNECTOR PCB SIDE A1561WV2-2P CP503 72796825 069W01001A CONNECTOR PCB SIDE 003P-2100 CP601 72799047 069S260639 CONNECTOR PCB SIDE A2001WR2-6P CP801 72799048 069W010340 CONNECTOR PCB SIDE 131001101K1 CD101A 72783129 06CH012006 CORD CONNECTOR CH012006 CD101B 72783128 06CH012007 CORD CONNECTOR CH012007 CP802A 72796751 067U005049 WIRE HOLDER B2013H02-5P CP802B 72796751 067U005049 WIRE HOLDER B2013H02-5P CP803A 72796750 067U004029 WIRE HOLDER B2013H02-4P CP803B 72796750 067U004029 WIRE HOLDER B2013H02-4P EL001 72797070 124120301A EYE LET XRY20X30BD EL002 72797069 124116281A EYE LET XRY16X28BD ! F501 72795538 081PC04005 FUSE 51MS040L ! FB401 72796666 043214050F TRANSFORMER,FLYBACK FNI14B002_M FH501 72794496 06710T0009 HOLDER,FUSE EYF-52BCY FH502 72794496 06710T0009 HOLDER,FUSE EYF-52BCY OS101 72783448 077Q000025 REMOTE RECEIVER KSM-713SY ! RY501 72796047 0560V20115 RELAY ALKS321 S101 72798395 WBL6026038 FLAT CABLE AWM2468 AWG26 4C BLACK 260MM S102 72798400 WCL6834038 FLAT CABLE AWM2468 AWG26 5C GRAY 340MM ! SP1001 75005271 070Y132031 SPEAKER S08F77 ! TH501 72794693 D8EE0B1400 DEGAUSS ELEMENT B59203-S1060-B14 TM101 72795473 076N0EH050 TRANSMITTER RC-EH050(CT-859) ! TU001 72783421 0163300022 RF UNIT 115-V-KA35ARH ! V801 72796972 098Q1404D1 CRT W/DY A34AGT13X98(DL) X601 72783450 100BT3R537 CRYSTAL HC-49U
J2-2
ELECTRICAL REPLACEMENT PARTS LISTRESISTOR
RC................... CARBON RESISTOR
CAPACITORSCC................…..CERAMIC CAPACITORCE................….. ALUMI ELECTROLYTIC CAPACITORCP................….. POLYESTER CAPACITORCPP...............….POLYPROPYLENE CAPACITORCPL...............…. PLASTIC CAPACITORCMP................…METAL POLYESTER CAPACITORCMPL................ METAL PLASTIC CAPACITORCMPP................ METAL POLYPROPYLENE CAPACITOR
J2-3
TOSHIBA CORPORATION1-1, SHIBAURA 1-CHOME, MINATO-KU, TOKYO 105-8001, JAPAN