138551508 lte parameter list

7/29/2019 138551508 LTE Parameter List

http://slidepdf.com/reader/full/138551508-lte-parameter-list 1/34

eNodeB Installation, Commissioning & Integration Acceptance Check List – Form TestCase Number Test Description Pre-commissioning Checks (locally on-site)(Installation) BBU Cabinet Installation Check: BBU is installed properly (Inside ODC/GBM belly/any other IP 55 box) CPRI Cable Connection Backhaul Cable connection D.C Ption GPS Cable Connection External Alarm cable Grounding Cable Connection Lables RRH Installation Check: RF Jumper Cable Connection CPRI Cable Connection Connection AISG Cable Connection Grounding Cable Connection Labelling of All Cna Installation Check: Antenna Installed and clamped properly Tilt and Azimuth acng to the planned values AISG cable labeled & connected properly Weather proofingRequired) RF jumper cable should not be sharply band. Labelling of All Cables GPSallation Check: eNB-ATP1-4 GPS has to installed on top section of the tower so thatclear visibility to the sky is available Weather proofing( if Required) GPS cablnection Cabling checks BBU to RRH CPRI Optical Cable RRH to Antenna RF Coaxial Cato Antenna RET Cable BBU to CSS Optical Cable Power Cables eNodeB earthing checksd RRHs should be grounded properly through separate grounding cables to the grounding Bars. Weather proofing to be done wherever required. Power Supply Polarity Check: BBU & RRH connected to -48V DC power supply from DCDB with proper polarity. Reflected Power/VSWR/Return Loss Check by VSWR meter / Site Master: VSWR measurement hould be done for all the sectors and connecting ports with external VSWR meteror site master for all the transmit paths of the antenna including jumper cableof the antenna. Measured VSWR value should be <=1.3 for feeder cable alone and <=1.5 for jumper and antenna together. Post-commissioning Checks (remotely in EMS) eNodeB discovery in EMS: eNodeB with 3 configured sectors should be completely visible & active in the EMS after integration. eNodeB Auto-configuration: Verify that

the configuration is as planned, the requisite parameters are enabled and the values of all parameters are exactly same as planned values. In case of any discrepancy from the planned value should be highlighted with proper reason. TransmitPower Check: Check measured value in EMS . The power of each Transmit Path shouldbe 40 dBm+0.5dB( 39.5 till 40.5dBm).LSM R snapshot should contain eNodeB Id withdate along with power value.5% of the sites for the city should be supported with Power measurement data with Site master/Power meter. Reflected Power/VSWR/Return Loss Check: Check the measured value in the EMS to ensure that the cabling between RRH and Antenna is proper and that Antenna is also not defective ü VSWR measurement should be done for all the sectors (RRHs) and connecting ports for all thetransmit paths of the antenna including jumper cable of the antenna. Measured VSWR value should be <=1.5 Network Connectivity and EPC Association check: Check that EMS does not show any Alarms related to EPC unavailability and also check whet

her the IP Addresses of MME and S-GW are as planned. ü IP assigned should be sameas per the IP plan. All critical, major alarms should be cleared for eNodeB to EPC association. Overall fault and alarm check: To check that there are no faults oralarms when the eNodeB comes up for the first time. All Critical/Major/Minor alarms related to eNodeB should be cleared. Hardware Version Check Report: The eNodeBs Hardware version should match the agreed Hardware version Software Version Check Report: All eNodeB should have latest SW release version working Uplink Interference Check: To check if the eNodeB reports any uplink, in-band interference even when all adjacent sites are blocked. This helps to discover and eliminate any unknown sources of interference. The value of UL RSSI should be less than -100 dBm.Any major/minor Uplink interference should be reported. RET integration check: Issue RET commands to change the Electrical Tilt and ensure that the Antenna’s RET controller responds properly and that there are not alarms related to it. Backhaul

stability test through Iperf for 1 minute Post-commissioning Checks (On Field with real UE to verify that all services are working and proper throughputs are achieved). Tests to be carried out below / very near to the commissioned cell siteensuring an SINR of greater than 25 dB. Tests to be automated as far as possible for rapid execution by semi-skilled engineers/technicians. Comply Comply Comply Comply Comply Comply Comply Comply Comply Comply Comply Passed / Failed Comments

eNB-ATP1-1



Comply Comply Comply Comply Comply Comply Comply Comply Comply Comply Comply Comply Comply Comply Comply Comply Comply Comply Comply Comply

eNB-ATP1-2

eNB-ATP1-3

eNB-ATP1-5

eNB-ATP1-6

eNB-ATP1-7

eNB-ATP1-8

Comply

eNB-ATP1-9

Comply

eNB-ATP1-10

Comply

eNB-ATP1-11

Comply

Comply Comply

eNB-ATP1-12

eNB-ATP1-13

Comply Comply

eNB-ATP1-14 eNB-ATP1-15 eNB-ATP1-16

Comply Comply Comply Partial Comply (Report only. Blocking all adjacent sites isnot always feasible in the field.).Report Only Comply Comply

eNB-ATP1-17

eNB-ATP1-18 eNB-ATP1-19



eNB-ATP1-20 eNB-ATP1-21 eNB-ATP1-22

Repetitive Attach – Detach Test – 5 times Ping Latency Test @ No Load. It should beless than 50 ms (eNobeB + backhaul) - 10 times Internet Browsing/Surfing: AccessGoogle.com and check if the Website is properly rendered on the Laptop VoLTE Service Test:

Comply Comply Comply

eNB-ATP1-23

IMS Video Call from Tablet connected to CPE-A to Tablet connected to CPE-B withboth CPE-A and CPE-B are in Medium SINR The end-to-end latency (From A-party toB-party) should be less than 100 ms Also measure Jitter and Packet Loss for thecall

eNB-ATP1-24

MBMS Services Test: To check that eMBMS is properly configured at the time of commissioning and broadcast services are operational.

All the special features service tests will be done separately as a part of service testing once the feature is available. Test procedures and criterial will bemutually agreed.

eNB-ATP1-25

LBS Service: To check that LCS configurations are properly made and UE Location/ Position can be determinted



eNodeB functionality and Single Cell Functional Test (SCFT) – FormNote: All three sectors of the eNodeB Under Test should be active and without any artificial loading (e.g. OCNS) in all tests listed below.

Test Case Number eNB-ATP2-1

Test Description Verification of Sector Swap Coverage Test Drive: Two UEs FirstUE with a long data call FTP DL, and the second UE with a long data call FTP UL: This will check Link Adaptation / AMC in both DL and UL and give an idea about theDL SINR and throughput distribution in the cell UE’s Tx Power Control MIMO Switctween SM and Tx Diversity Cell Edge for 256 Kbps in UL and 2Mbps in DL RF Parameters to be collected and post-processed: RSRP, RSRQ, SINR UE Tx Power and Power Head, RB Allocation, Rank Indicator DL PHY Throughput, UL PHY Throughput and BLER PCIng Area Attach Success Rate Drop Rate Handover Report has to be generated afteg clockwise and Anti-clockwise handover Coverage Test Drive with eMBMS Service:To verify coverage of eMBMS and check if broadcast delivery can happen satisfactorily over a given service area with the configured MCS values Multi-UE tests tobe done with 5 UEs in either Alpha, Beta or Gamma Sector @ SINR values rangingfrom 10 to 15 dB with single UE. Automation Scripts can be used for quick and reliable execution to be done in either Alpha, Beta or Gamma Sector @ SINR valuesranging from 10 to 15 dB with single UE. Automation Scripts can be used for quick and reliable execution.

eNB-ATP2-2

eNB-ATP2-3

eNB-ATP2-4 eNB-ATP2-5

Repetitive Attach – Detach Test – 20 times Throughput Stability Test with each UE ina fixed location with FTP DL and UL together. The 10 minutes of throughput graph needs to be obtained.

Site Information Sr. No. 1 Parameter Physical Parameters Latitude



2 3 4 5 6 7 8 9 10 11 12 13 14

Longitude Antenna Height Antenna Azimuth Antenna Tilt: Mechanical Antenna Tilt:Electrical from LSM-R Antenna Make & Model Important Configuration Parameters EARFCN PCID Cell ID TAC Tx Power from LSM-R MIMO Mode (TM3/TM4) from LSM-R MIMO Type (2x2, 4x2) from LSM-R

Report Checklist for SCFT Sr. No. Test Case Reference eNodeB ATP2-2 eNodeB ATP2-2 eNodeB ATP2-2 eNodeB ATP2-2

1. 2. 3. 4.

5.

eNodeB ATP2-2

6.

eNodeB ATP2-2



6.

eNodeB ATP2-2

9. 10. 11. 12. 13. 14. 15.

eNodeB ATP2-2 eNodeB ATP2-2 eNodeB ATP2-2 eNodeB ATP2-3 eNodeB ATP2-2 eNodeB ATP2-2 eNodeB ATP2-2

Drive test KPI Sr. No ACCESSIBILITY 1 2 3 4 RETAINABILITY 5 MOBILITY 6 7 Coverage Quality 8 9 10 11 12 13 14 15 Access Time 16 17 18 19 20 Key Performance Indicator PRACH Success Rate (UE End) Attach Success Rate Successful data transmission download attempts Successful data transmission upload attempts Drop Calls % Handover success rate Tracking Area Update Success Rate Unicast Block Error Rate eMBMS Block Error Rate DL SINR with >-2 dB DL RSRP with >-108dBm Average DL Throughput Average UL Throughput DL Throughput >2Mbps UL Throughput >256Kbps Attach Setup time Latency: Audio Call Latency: Video Call Latency: Data Latency: Data (inter-active)



21

QCI 5 (IMS Signaling) Radio Link Latency



oading (e.g. OCNS) in all tests listed below.

Passed / Failed

Comments Comply

Comply

Comply only after it is launched and Devices are made available

Comply (Only for RCP and Jamnagar Pilot Trials) Comply (Only for RCP and Jamnagar Pilot Trials)

Samsung Comments

Comply. Need to get the values from the field



Comply. Need to get the values from the field Comply Comply Comply Comply ComplyComply Comply Comply Comply Comply Comply Comply

Type of Report Log of RRC and NAS Messages DL SINR, DL MCS and DL Throughput Snapshot on both UEs UL SINR, UL MCS and UL Throughput Snapshot on both UE PCID Plot for each sector Plot of following parameters on Google Map: 1. RSRP 2. RSRQ 3.SINR 4. UE Tx Power 5. Power Headroom 6. MCS 7. RB Allocation 8. Rank Indicator9. DL PHY Throughput 10. UL PHY Throughput 11. BLER 12. PCID 13. CQI Histogram/CDF of the following parameters 1. RSRP 2. RSRQ 3. SINR 4. UE Tx Power

Samsung Comments Comply Comply Comply Comply

Comply

Comply



5. Power Headroom 6. MCS 7. RB Allocation 8. Rank Indicator 9. DL PHY Throughput10. UL PHY Throughput 11. BLER Handover Success Rate and Throughput drop duringHandover Drop Call Rate Attach/Detach Latency Sector wise Handover Latency Sector wise MBMS throughput and BLER Average DL/UL throughput RACH acknowledgement Success Rate Command list run during the drive test

Comply

Comply Comply Comply Comply Comply Comply Comply

Value > 99 > 99 >99 >99 <2 > 98 > 98 <1 <1 95 95 20 2.5 95 95 2 < 100 < 105 < 150 < 50

Unit % % % % % % % % % % area % area Mbps Mbps % area % area Sec ms ms ms ms



< 80

ms



Pre-SCFT(If some changes are done during SCFT)



Acceptance TestseNodeB Cluster Drive Test – FormNote: All three sectors of the eNodeB Under Test should be active and without any artificial loading (e.g. OCNS) in all tests listed below.

Test Case Number

Test Description Coverage Test Drive: Two UEs First UE with a long data call FTPDL, and the second UE with a long data call FTP UL: This will check Link Adaptation / AMC in both DL and UL and give an idea about the DL SINR and throughput distribution in the cell UE’s Tx Power Control MIMO Switching between SM and Tx DiverEdge for 256 Kbps in UL and 2Mbps in DL RF Parameters to be collected and post-processed: RSRP, RSRQ, SINR UE Tx Power and Power Headroom MCS, RB Allocation, tor DL PHY Throughput, UL PHY Throughput and BLER PCID Tracking Area Attachate Handover Report has to be generated after performing clockwise and Anti-clockwise handover Coverage Test Drive with eMBMS Service: To verify coverage of eMBMSand check if broadcast delivery can happen satisfactorily over a given service area with the configured MCS values

Passed / Failed

eNB-ATP3-1

eNB-ATP3-2

Sr. No.

Parameter Physical Parameters Latitude Longitude Antenna Height Antenna AzimuthAntenna Tilt: Mechanical Antenna Tilt: Electrical from LSM-R Antenna Make & Model Important Configuration Parameters EARFCN PCID Cell ID TAC Tx Power from LSM-RMIMO Mode (TM3/TM4) from LSM-R MIMO Type (2x2, 4x2) from LSM-R

Planned

1 2 3 4 5 6 7 8 9 10 11 12 13 14



Drive test KPI Sr. No Key Performance Indicator ACCESSIBILITY 1 PRACH Success Rate (UE End) 2 Attach Success Rate 3 Successful data transmission download attempts 4 Successful data transmission upload attempts RETAINABILITY 5 MOBILITY 6 7 Drop Calls % Handover success rate Tracking Area Update Success Rate Value > 99 >99 >99 >99 <2 > 98 > 98 <1 <1 95 95 20 2.5 95 95 2 < 100 < 105 < 150 < 50 < 80

Coverage Quality 8 Unicast Block Error Rate 9 eMBMS Block Error Rate 10 DL SINRwith >-2 dB 11 DL RSRP with >-108dBm 12 Average DL Throughput 13 Average UL Throughput 14 DL Throughput >2Mbps 15 UL Throughput >256Kbps Access Time 16 Attach Setup time 17 Latency: Audio Call 18 Latency: Video Call 19 Latency: Data 20 Latency: Data (inter-active) 21 QCI 5 (IMS Signaling) Radio Link Latency Parametersto be covered in Reports: a.) Geographical b.) Statistical (Histogram/CDF) 1. DLSINR Distribution

2.

DL RSRP Distribution

3.

DL RSRQ Distribution

4.

CQI Distribution

5.

MCS Distribution

6.

TM Mode Distribution



7.

Rank Indicator Distribution

8.

RB Distribution

9.

DL Throughput Distribution

10.

UL Throughput Distribution

11.

eMBMS Throughput Distribution

12.

eMBMS BLER rate Distribution

13.

Unicast BLER rate Distribution

14.

UE Transmit Power Distribution

15.

Power Headroom Distribution

16.

Physical Cell ID Distribution (Only on geographic map)

Signalling Success/Failure Reports on Geographic Maps 1. 2. 3. 4. 5. 6. RACH Acknowledgement Attach Success/Failure ERAB Signalling Handover Tracking Area Update Drop Call

7. Detach Latency Reports: Statististical 1. 2. 3. Attach Latency Handover Latency Ping Latency RRC Message



ests

artificial loading (e.g. OCNS) in all tests listed below.

Comments

Comply


Observed

Changes

Final



Unit % % % % % % % % % % area % area Mbps Mbps % area % area Sec ms ms ms ms ms

//Qualcomm LTE -> Random Access Procedure Statistics -> PS Call Statistics(attach & Detach log file) Statistics -> PS Call Statistics(DL log file) Statistics ->PS Call Statistics(UL log file) Statistics -> PS Call Statistics(DL/UL log file) Table -> LTE Signaling Message -> RRC -> HO Statistics -> Intra LTE HO -> Attempt/Success Table -> LTE Signaling Message -> NAS -> TAC Procedure -> Tracking Area UpdateStatistics Map -> Qualcomm LTE -> PDSCH BLER Info -> Total -> Total BLER Map -> Qualcomm LTE -> PMCH BLER Info -> Total -> Total BLER Map -> QualcommLTE -> Intra freq measurement info -> Serving Cell -> Serving SINR -> SINR Map -> Qualcomm LTE -> Intra freq measurement info -> Serving Cell -> Serving RSRP ->RSRP Table -> Qualcomm LTE -> Physical Throughput -> PDSCH Throughput -> TotalThroughput Table -> Qualcomm LTE -> Physical Throughput -> PUSCH Throughput -> Total Throughput Map -> Qualcomm LTE -> Physical Throughput -> PDSCH Throughput -> Total Throughput Map -> Qualcomm LTE -> Physical Throughput -> PUSCH Throughput -> Total Throughput

Table -> LTE Signaling Message -> NAS -> Attach Procedure -> Attach Time(Attach& Detach log file) ? ? ? ? ?

KML : Map -> Qualcomm LTE -> Intra freq measurement info -> Serving Cell -> Serving SINR -> SINR( CDF : CDF -> Qualcomm LTE -> Intra freq measurement info -> Serving Cell -> Serving SINR -> SINR Histogram : Map -> Qualcomm LTE -> Intra freqmeasurement info -> Serving Cell -> Serving SINR -> KML : Map -> Qualcomm LTE -

> Intra freq measurement info -> Serving Cell -> Serving RSRP -> RSRP CDF : CDF-> Qualcomm LTE -> Intra freq measurement info -> Serving Cell -> Serving RSRP -> RSRP Histogram : Map -> Qualcomm LTE -> Intra freq measurement info -> ServingCell -> Serving RSRP -> KML : Map -> Qualcomm LTE -> Intra freq measurement info -> Serving Cell -> Serving RSRQ -> RSRQ CDF : CDF -> Qualcomm LTE -> Intra freq measurement info -> Serving Cell -> Serving RSRQ -> RSRQ Histogram : Map -> Qualcomm LTE -> Intra freq measurement info -> Serving Cell -> Serving RSRQ KML :Map -> Qualcomm LTE -> Channel Quality info -> WideBand CQI(Mouse Right Click ->Export CDF : CDF -> Qualcomm LTE -> Channel Quality info -> WideBand CQI Histogram : Map -> Qualcomm LTE -> Channel Quality info -> WideBand CQI(Click Bar Menu) KML : Map -> Qualcomm LTE -> ML1 Downlink Info -> MCS Index0(Avg) -> (Mouse Right Click -> Exp CDF : CDF -> Qualcomm LTE -> ML1 Downlink Info -> MCS Index0(Avg) Histogram : Map -> Qualcomm LTE -> ML1 Downlink Info -> MCS Index0(Avg) -> (C

lick Bar Menu) KML : Map -> LTE Signaling Message -> RRC -> Antenna info -> Transmission Mode -> (Mouse Right



CDF : CDF -> LTE Signaling Message -> RRC -> Antenna info -> Transmission Mode Histogram : LTE Signaling Message -> RRC -> Antenna info -> Transmission Mode ->(Click Bar Menu KML : Map -> Qualcomm LTE -> Channel Quality info -> Rank Index(Mouse Right Click -> Export -> to CDF : CDF -> Qualcomm LTE -> Channel Quality info -> Rank Index Histogram : Map -> Qualcomm LTE -> Channel Quality info -> Rank Index(Click Bar Menu) KML : Map -> Qualcomm LTE -> ML1 Downlink Info -> RB Num(Avg) -> (Mouse Right Click -> Export CDF : CDF -> Qualcomm LTE -> ML1 DownlinkInfo -> RB Num(Avg) Histogram : Map -> Qualcomm LTE -> ML1 Downlink Info -> RB Num(Avg) -> (Click Bar Menu) KML : Map -> Qualcomm LTE -> Physical Throughput ->PDSCH Throughput -> Total Throughput -> ( CDF : CDF -> Qualcomm LTE -> PhysicalThroughput -> PDSCH Throughput -> Total Throughput Histogram : Map -> Qualcomm LTE -> Physical Throughput -> PDSCH Throughput -> Total Throughp KML : Map -> Qualcomm LTE -> Physical Throughput -> PUSCH Throughput -> Total Throughput -> ( CDF : CDF -> Qualcomm LTE -> Physical Throughput -> PUSCH Throughput -> Total Throughput Histogram : Map -> Qualcomm LTE -> Physical Throughput -> PUSCH Throughput -> Total Throughp KML : Map -> Qualcomm LTE -> PMCH Throughput -> Total Throughput -> (Mouse Right Click -> Exp CDF : CDF -> Qualcomm LTE -> PMCH Throughput -> Total Throughput Histogram : Map -> Qualcomm LTE -> PMCH Throughput -> Total Throughput -> (Click Bar Menu) KML : Map -> Qualcomm LTE -> PMCH BLER Info -> Total -> Total BLER -> (Mouse Right Click -> Expo CDF : CDF -> Qualcomm LTE -> PMCHBLER Info -> Total -> Total BLER Histogram : Qualcomm LTE -> PMCH BLER Info ->Total -> Total BLER -> (Click Bar Menu) KML : Map -> Qualcomm LTE -> PDSCH BLERInfo -> Total -> Total BLER -> (Mouse Right Click -> Exp CDF : CDF -> Qualcomm LTE -> PDSCH BLER Info -> Total -> Total BLER Histogram : Qualcomm LTE -> PDSCH B

LER Info -> Total -> Total BLER -> (Click Bar Menu) KML : Map -> Qualcomm LTE ->Power Info -> Tx Power -> PUSCH/PUCCH/SRS -> (Mouse Right Click CDF : CDF -> Qualcomm LTE -> Power Info -> Tx Power -> PUSCH/PUCCH/SRS Histogram : Map -> Qualcomm LTE -> Power Info -> Tx Power -> PUSCH/PUCCH/SRS -> (Click Bar Me KML : Map-> Qualcomm LTE -> Power Info -> min(PMAX,TxPower) -> Power Headroom -> (Mouse RCDF : CDF -> Qualcomm LTE -> Power Info -> min(PMAX,TxPower) -> Power HeadroomHistogram : Map -> Qualcomm LTE -> Power Info -> min(PMAX,TxPower) -> Power Headroom -> (Cl

KML : Map -> Qualcomm LTE -> Intra freq measurement info -> Serving Cell -> Serving PCI(Mouse R

??

? KML : Map -> LTE Signaling Message -> NAS -> Attach Procedure -> Attach Request/Accept/Comple ? KML : Map -> LTE Signaling Message -> RRC -> HO Statistics ->Intra LTE HO -> Attempt/Success(Mo KML : Map -> LTE Signaling Message -> NAS ->TAC Procedure -> Tracking Area Update Request/Acc KML : Map -> Call Result -> FTP Call(Mouse Right Click -> Export -> to KML(Legend) KML : Map -> LTE SignalingMessage -> NAS -> Detach Procedure -> Detach Request/Accept(Mouse

Table -> LTE Signaling Message -> NAS -> Attach Procedure -> Attach Time(Attach& Detach log file) Table -> LTE Signaling Message -> RRC -> HO Statistics -> Intra LTE HO -> Attempt/Success/Duration

right click on table-> right click & select new filter tree-> select msg-> expor

t to xls format



ntra LTE HO -> Attempt/Success > Tracking Area UpdateStatistics

Serving Cell -> Serving SINR -> SINR Serving Cell -> Serving RSRP -> RSRP Throughput -> Total Throughput Throughput -> Total Throughput hroughput -> Total Throughput hroughput -> Total Throughput

e -> Attach Time(Attach & Detach log file)

fo -> Serving Cell -> Serving SINR -> SINR(Mouse Right Click -> Export -> to KML(Legend) o -> Serving Cell -> Serving SINR -> SINR ment info -> Serving Cell ->Serving SINR -> SINR(Click Bar Menu) fo -> Serving Cell -> Serving RSRP -> RSRP(Mouse Right Click -> Export -> to KML(Legend) o -> Serving Cell -> Serving RSRP-> RSRP ment info -> Serving Cell -> Serving RSRP -> RSRP(Click Bar Menu) fo ->Serving Cell -> Serving RSRQ -> RSRQ(Mouse Right Click -> Export -> to KML(Legend) o -> Serving Cell -> Serving RSRQ -> RSRQ ment info -> Serving Cell -> Serving RSRQ -> RSRQ(Click Bar Menu) deBand CQI(Mouse Right Click -> Export -> to KML(Legend)

-> WideBand CQI(Click Bar Menu) S Index0(Avg) -> (Mouse Right Click -> Export ->to KML(Legend)

> MCS Index0(Avg) -> (Click Bar Menu) o -> Transmission Mode -> (Mouse Right Click -> Export -> to KML(Legend)



-> Transmission Mode -> Transmission Mode -> (Click Bar Menu) nk Index(Mouse Right Click -> Export -> to KML(Legend)

-> Rank Index(Click Bar Menu) Num(Avg) -> (Mouse Right Click -> Export -> to KML(Legend)

> RB Num(Avg) -> (Click Bar Menu) SCH Throughput -> Total Throughput -> (Mouse Right Click -> Export -> to KML(Legend) CH Throughput -> Total Throughput -> PDSCH Throughput -> Total Throughput -> (Click Bar Menu) SCH Throughput -> Total Throughput -> (Mouse Right Click -> Export -> to KML(Legend) CH Throughput -> TotalThroughput -> PUSCH Throughput -> Total Throughput -> (Click Bar Menu) l Throughput -> (Mouse Right Click -> Export -> to KML(Legend)

> Total Throughput -> (Click Bar Menu) > Total BLER -> (Mouse Right Click -> Export -> to KML(Legend)

Total BLER -> (Click Bar Menu) > Total BLER -> (Mouse Right Click -> Export -> to KML(Legend)

Total BLER -> (Click Bar Menu) PUSCH/PUCCH/SRS -> (Mouse Right Click -> Export -> to KML(Legend)

wer -> PUSCH/PUCCH/SRS -> (Click Bar Menu) xPower) -> Power Headroom -> (Mouse Right Click -> Export -> to KML(Legend) xPower) -> Power Headroom MAX,TxPower) ->

Power Headroom -> (Click Bar Menu)

fo -> Serving Cell -> Serving PCI(Mouse Right Click -> Export -> to KML(Legend)

edure -> Attach Request/Accept/Completel/Reject(Mouse Right Click -> Export -> to KML(Legend) Attach/Detach log file

s -> Intra LTE HO -> Attempt/Success(Mouse Right Click -> Export -> to KML(Legend) ure -> Tracking Area Update Request/Accept(Mouse Right Click -> Export -> toKML(Legend) DL log file xport -> to KML(Legend) cedure -> Detach Request/Accept(Mouse Right Click -> Export -> to KML(Legend) Attach/Detach log file

e -> Attach Time(Attach & Detach log file) ntra LTE HO -> Attempt/Success/Durati

on

elect msg-> export to xls format



Acceptance TestsCity-wide Drive Test – FormNote: All three sectors of the eNodeB Under Test should be active and without any artificial loading (e.g. OCNS) in all tests listed below.

Test Case Number

Test Description Coverage Test Drive: Two UEs First UE with a long data call FTPDL, and the second UE with a long data call FTP UL: This will check Link Adaptation / AMC in both DL and UL and give an idea about the DL SINR and throughput distribution in the cell UE’s Tx Power Control MIMO Switching between SM and Tx DiverEdge for 256 Kbps in UL and 2Mbps in DL RF Parameters to be collected and post-processed: RSRP, RSRQ, SINR UE Tx Power and Power Headroom MCS, RB Allocation, tor DL PHY Throughput, UL PHY Throughput and BLER PCID Tracking Area Attachate Handover Report has to be generated after performing clockwise and Anti-clockwise handover Coverage Test Drive with eMBMS Service: To verify coverage of eMBMSand check if broadcast delivery can happen satisfactorily over a given service area with the configured MCS values

Passed / Failed

eNB-ATP4-1

eNB-ATP4-2

Sr. No.

1 2 3 4 5 6 7 8 9 10 11 12 13 14

Parameter Physical Parameters Latitude Longitude Antenna Height Antenna AzimuthAntenna Tilt: Mechanical Antenna Tilt: Electrical from LSM-R Antenna Make & Model Important Configuration Parameters EARFCN PCID Cell ID TAC Tx Power from LSM-RMIMO Mode (TM3/TM4) from LSM-R MIMO Type (2x2, 4x2) from LSM-R

Planned



Drive test KPI Sr. No Key Performance Indicator ACCESSIBILITY 1 PRACH Success Rate (UE End) 2 Attach Success Rate 3 Successful data transmission download attempts 4 Successful data transmission upload attempts RETAINABILITY 5 MOBILITY 6 7 Drop Calls % Handover success rate Tracking Area Update Success Rate Value > 99 >99 >99 >99 <2 > 98 > 98 <1 <1 95 95 20 2.5 95 95 2 < 100 < 105 < 150 < 50 < 80

Coverage Quality 8 Unicast Block Error Rate 9 eMBMS Block Error Rate 10 DL SINRwith >-2 dB 11 DL RSRP with >-108dBm 12 Average DL Throughput 13 Average UL Throughput 14 DL Throughput >2Mbps 15 UL Throughput >256Kbps Access Time 16 Attach Setup time 17 Latency: Audio Call 18 Latency: Video Call 19 Latency: Data 20 Latency: Data (inter-active) 21 QCI 5 (IMS Signaling) Radio Link Latency Parametersto be covered in Reports: a.) Geographical b.) Statistical (Histogram/CDF) 1. 2.3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. DL SINR Distribution DL RSRP Distribution DL RSRQ Distribution CQI Distribution MCS Distribution TM Mode Distribution Rank Indicator Distribution RB Distribution DL Throughput Distribution UL Throughput Distribution eMBMS Throughput Distribution eMBMS BLER rate DistributionUnicast BLER rate Distribution UE Transmit Power Distribution Power Headroom Distribution



16.

Physical Cell ID Distribution (Only on geographic map)

Signalling Success/Failure Reports on Geographic Maps 1. 2. 3. 4. 5. 6. RACH Acknowledgement Attach Success/Failure ERAB Signalling Handover Tracking Area Update Drop Call

Detach 7. Latency Reports: Statististical 1. 2. 3. Attach Latency Handover Latency Ping Latency



e Tests

ficial loading (e.g. OCNS) in all tests listed below.

Comments

Comply


Observed

Changes

Final



Unit % % % % % % % % % % area % area Mbps Mbps % area % area Sec ms ms ms ms ms



Samsung will provide Self Certification stating the site is EMF compliant according to the Document No. TEC/TP/EMF/001/0 Below) provided by the TEC department or any updations/revisions made henceforth by the TEC and if the site is not complia make the site compliant and submit the self certification

D:\EMF\Test Procedure EM Fields From BTS Antennae OCT 2012.pdf



to the Document No. TEC/TP/EMF/001/02.OCT. 2012 (attached h by the TEC and if the site is not compliant then samsung has to he self certification

138551508 lte parameter list

Documents