COMPONENT PARTS

11

Thank you for selecting our product. Before starting installation, please read this manual thoroughly to ensure correct installation.Please keep this manual at hand for future reference.

ABOUT THE PRODUCT

Warning: If not followed, death or serious injury may result.

Caution: If not followed, injury or damage may result.

This (lateral swing door system) should be installed by an experienced person. If the system is not installed correctly,the door will not operate smoothly, and may cause injury.It is necessary to manufacture the frame with sufficient strength so it endures the weight of the door and impact shocks upon opening/closing the door. A frame with poor strength might result in improper and slower movement of the door. In the worst case, the door might drop down and cause injury.Do not try to use this product for any other purposes than originally intended for. Do not use the parts for applications that are out of specifications.Do not disassemble nor modify any parts than those described in this document.Hinges are only designed to hold the door. Do not sit on them or hang anything else than the door.Do not use excessive force to further open the completely opened door or open/close the door as this could result in malfunction.

FOR YOUR SAFE WORK AND CORRECT INSTALLATION

・ Screwdriver(+) No.3　 ・ Screwdriver(+) No.2　 ・ Hex key 4mm　 ※ Aluminum frame 40×160　

Screw（M6×12） Nut × 8 set　 Aluminum frame fixing angle, including fixing screws and nuts.　 Hex key 5mm

●●●●

Can be used for both cabinet and passage doors.

Easy installation and adjustment.

Door will be flush with surrounding walls.

There is no need of embedding a rail on the floor.

Installation Instructions LIN-X800

Truss head tappingscrew 6×25 　　　 ×16

Hinge (A) ×1

Connecting Bar ×1 (Packed separately.)

ProhibitedWarningCaution

Required

Meanning of symbols

Hinge (B) ×1 Mounting Plate Cover ×4(Door Side)

Mounting Plate Cover ×4(Hinge Side)

Truss head screw M5×10 　　　 ×8

Square nutsM5 t=3　　 ×8

Spanner 8mm ×1

Connecting BarCap 　　　 ×2

TOOLS NEEDED FOR ASSEMBLY (Please prepare ※ when installing on aluminum frame.)

This lateral swing door system is a part for furniture or architectural fittings. After installation, make sure to test the finished product thoroughly to ensure that it is well-functioning and safe, inform the user to operate safely.Make sure to follow the designated measurements and specifications as well as horizontal and vertical angles. Make sure that the frame is not warped, since it may affect the movement of the door.Sugatsune conducts extensive quality checks on this product. However, if any defects are found on the product, contact the retailer.When cleaning heavy grime, wipe off with a neutral detergent diluted with water.Make sure to test the screws for slack at regular intervals (one month from first usage, half year and then one time every year is recommended).

2

INSTALLATION PROCEDURE

● For wood frame installation,

　 please refer to ー .

● For aluminum frame installation,

please refer to ー　　 and ー .1 8 91 4 11

1 Hole ProcessingPlease refer to the cut out dimensions shown on the right or the template.

For installation on an aluminum side frame, please refer only to the door side.

SPECIFICATIONS

Clearances for hinge side and tip side of the door required to be more than 8mm.

This drawing shows the left handed opening type. Installation for right handed opening is symmetrically opposite.

DoorJamb

Clearance

Door Width Door Thickness

Door Height

Door Weight Temperature of use

24 － 40 mm

0 ～ 40

750 － 850 mm

１９２０[2320]

2080[２４８０]

1904[２３０４]

2０９６[2496]

1４0395 + door overlay 20

４95 + door overlay

door overlay

・［ ］: LIN-X800H

Max.40 kg/Door

LIN-X800

LIN-X800H ( Connecting Bar L=2500 ) … － 2980mm

( Connecting Bar L=2100 ) … － 2400mm

31 m

inim

um31

min

imum

Cle

aran

ce b

etw

een

the

floor

a

nd th

e do

or

１５ m

inim

um

3

Screwdriver(+) No.3

2 Pre-Installation Pre-fix the 4 lower screws ( 2 for top and 2 for bottom arm) on the hinge side, and 4 upper screws on the door side, using the truss tapping 6x25 screws provided.* For the installation on the aluminum side board, please refer only to the door side.

Leave a 5mm gap in order to slide the hinge.

Door Side Hinge Side

≒ 80mm

Set the hinges so that the arrows and the parallel adjustment screws are both facing each other.

Hinge (A) Hinge (B)

Square nuts Square nuts

3 Assembling of Hinges and Connecting Bar

Door(back side)

Insert the square nuts into the connecting bar.

Parallel adjustment screws

Assembly direction arrow Assembly direction arrow

4

Align the end of hinge and connecting rod and tighten the 8 screws to the square nuts in the rod.

Align the ends.

Screwdriver(+) No.2

Truss head screwM5×10

Please check the hinge is securely fit in the ribs of the connecting bar.

Square nuts

Fit here

Clearance

4 Installation of Connecting Bar Caps (Two places of both ends)

5

5

6

Mounting Hinges

Support hinges with hand while installing the bar to prevent unwanted load.

Tighten all screws.

Installing Door

We recommend that 2 people install the door in orderto reduce risks of injury and damage to the door.

MountingPlate(Door Side)

Pre-fixed screws

1 2

1 2

Tighten all screws.

6

Door Side

Hinge Side

Hinge Side

Door Side

7 Door Adjustments

Horizontal・Vertical・Parallel adjustment

Depth adjustment

Removing the fixing screw may result in the door falling and injuring someone and/or damaging the door.

1 2 3

1 2 3

1 2 3

1 2 3

Horizontal adjustment±7 [mm]

Vertical adjustment±7 [mm]

Parallel adjustment±4 [°]

Depth adjustment±5 [mm]

Loosen half turn only

Fasten

Loosen half turn only

Fasten

Loosen half turn only

Fasten

FastenLoosen

（Recommended closing torque: 2 N・m）

7

8 Install the Mounting Plate Cover

Mounting Plate Cover (Door Side) Mounting Plate Cover (Hinge Side)

Bracket Bracket

Clips

ClipsEnsure correct alignment.

Insert and fit into the plate.

Plate

ALUMINUM FRAME SIDE BOARD

9 Install on the Aluminum Frame

Aluminum Frame Dimensions Fix the aluminum frame

Width 160 mm

Pitch 120 mm

Thickness 40 mm

Ceiling

Floor

8

Ceiling

Floor

2018.12　1262-1

1０ Mounting Hinges

1１ Installing Door

Support hinges with hand while installing the bar to prevent unwanted load.

We recommend that 2 people install the door in orderto reduce risks of injury and damage to the door.

Tighten all screws.

MountingPlate(Door Side)

● For the adjustment and installation of the cover, please refer to 　　　and 　　 .87

(Recommended closing torque: 10N・m)

* Screw (M6×12）not included.

Front screw detail.

Pre-fixed screws

1 2

1 2

8