12. engine
TRANSCRIPT
-
8/9/2019 12. Engine
1/53
1 | P a g e
-
8/9/2019 12. Engine
2/53
2 | P a g e
Engine
Open a new part with model units set to
millimeters.
Select the three planes in the feature tree and
make them visible by clicking on the glasses.
Select the Front Plane and create a sketch
by clicking on the 2D Sketch icon
Draw the sketch as shown in the picture.
Create an extrude
Go to: Insert > Boss/Base > Extrude
Direction 1 : Blind
Change into 200 mm
Click OK
-
8/9/2019 12. Engine
3/53
3 | P a g e
Create a new plane parallel at the Front Plane
Go to: Insert > Reference Geometry > Plane
Select the Front Plane.
Select the midpoint of Extrude1 as shown
in the picture.
Click OK
Change the name of the new Plane1
Double click on Plane1 in the feature tree.
Change the name into: MIDPLANE ENGINE
Select the MIDPLANE ENGINE and create a new sketch
Insert a sketch underlay.
For this part of the chopper we use a hand madesketch as underlay to simplify the design process
of the engine.
Go to: Tools > Sketch Tools > Sketch Picture
Select Chopper Underlay.Jpeg
Click: open
-
8/9/2019 12. Engine
4/53
4 | P a g e
Change the dimensions of and as shown in the picture.
Change the position of the underlay to ensure that the bottom of Extrude1 is equal
with the engine on the underlay.
Click OK
-
8/9/2019 12. Engine
5/53
5 | P a g e
Change the name of Sketch2
Double click on Sketch2 in the feature tree.
Change the name into: ENGINE UNDERLAY
Hide the underlay if this is appropriate
Click on Chopper Underlay in the feature tree and hide this by
clicking on the glasses. Use the underlay whenever you want.
Select the green surface of Extrude1 as shown
in the picture and create a new sketch
Draw the sketch as shown in the picture.
Create an extrude
Go to: Insert > Boss/Base > Extrude
Direction 1 : Blind
Change into 50 mm
Click OK
-
8/9/2019 12. Engine
6/53
6 | P a g e
Select the front surface of Extrude2 and draw the sketch as shown in the picture
Create an extrude
Go to: Insert > Boss/Base > Extrude
Direction 1 : Blind
Change into 40 mm
Click OK
Select the MIDPLANE ENGINE andcreate a new sketch
Draw the sketch as shown in
the picture.
Create an extrude
Go to: Insert > Boss/Base > Extrude
Direction 1 : Mid Plane
Change into 150 mm
Click OK
-
8/9/2019 12. Engine
7/53
7 | P a g e
Create eleven fillets
Select the green edges as shown in the picture.
Go to: Insert > Features > Fillet/Round > 50 mm
Click OK
Select the Front Plane and
create a new sketch
Draw the sketch as shown in the
picture and detail.
Detail
Create a revolve
Go to:Insert > Boss/Base > Revolve
Axis of revolution : Select the green line asshown in the picture.
Click OK
-
8/9/2019 12. Engine
8/53
8 | P a g e
Create a new plane parallel at the Right Plane
Go to: Insert > Reference Geometry > Plane
Select the Right Plane.
Change the Offset Distance into 350 mm.
Ensure that the offset is directed to the middle
of the engine.
If not, select Reverse direction
Click OK
Select the new Plane2 and create a new sketch
Draw the sketch as shown in the picture.
Create a revolve
Go to:Insert > Boss/Base > Revolve
Axis of revolution : Select the green
line as shown in
the picture.
Click OK
-
8/9/2019 12. Engine
9/53
9 | P a g e
Select the green surface of Revolve1 as shownin the picture and create a new sketch
Draw the sketch as shown in the picture and detail.
Detail
-
8/9/2019 12. Engine
10/53
1 | P a g e
Create a circular pattern sketch
Go to: Tools > Sketch Tools >
Circular Pattern
Pattern Axis : Select the originin the middle of
the circle.
Number of instances : 40
Angle : 360 deg
Radius : 60 mm
Arc Angle : 270 deg
Select the Equal spacing option
Entities to Pattern : Select the
rectangle
of Sketch8
Click OK
-
8/9/2019 12. Engine
11/53
11 | P a g e
Create a new sketch as shown in the picture and detail.
Detail
-
8/9/2019 12. Engine
12/53
12 | P a g e
Create another circular pattern sketch
Go to: Tools > Sketch Tools >
Circular Pattern
Pattern Axis : Select the midpointof the circle.
Number of instances : 44
Angle : 360 deg
Radius : 70 mm
Arc Angle : 270 deg
Select the Equal spacing option
Entities to Pattern : Select therectangle
Click OK
-
8/9/2019 12. Engine
13/53
13 | P a g e
Create an extruded cut
Go to: Insert > Boss/Base > Extrude
Direction 1 : Blind
Change into 88 mm
Click OK
Create a dome
Go to: Insert > Feature > Dome
Select the green surfaces of Revolve1
and Revolve2.
Change the Distance into 10 mm
Click OK
Create a new plane parallel at the MIDPLANE ENGINE
Go to: Insert > Reference Geometry > Plane
Select the MIDPLANE ENGINE.
Change the Offset Distance into 250 mm.
Ensure that the offset direction is correct.
If not, select Reverse direction
Click OK
Select the green surface of Dome1 as shown
in the picture and create a new sketch
Draw the sketch as shown in the picture
on the next page.
-
8/9/2019 12. Engine
14/53
14 | P a g e
Create a circular pattern sketch
Go to: Tools > Sketch Tools >
Circular Pattern
Pattern Axis : Select the midpointof the big circle.
Number of instances : 12
Angle : 360 deg
Radius : 55 mm
Arc Angle : 270 deg
Select the Equal spacing option
Entities to Pattern : Select the
Small circle
Click OK
Create an extruded cut
Go to: Insert > Cut > Extrude
Direction 1 : Offset From Surface
Change into 3 mm
Select the pink surface as shown in the picture.
Select the Reverse offset option.
Click OK
-
8/9/2019 12. Engine
15/53
15 | P a g e
Select the other green surface of Dome1 as shown
in the picture and create a new sketch
Create a circular pattern sketch
Go to: Tools > Sketch Tools >
Circular Pattern
Pattern Axis : Select the midpoint
of the big circle.
Number of instances : 14
Angle : 360 deg
Radius : 65 mm
Arc Angle : 270 deg
Select the Equal spacing option
Entities to Pattern : Select the
Small circle
Click OK
-
8/9/2019 12. Engine
16/53
16 | P a g e
Create an extruded cut
Go to: Insert > Cut > Extrude
Direction 1 : Offset From Surface
Change into 3 mm
Select the pink surface as shown
in the picture.
Select the Reverse offset option.
Click OK
Create a chamfer
Go to: Insert > Features > Chamfer
Select the green surfaces as shown in the picture.
Select the Angledistance option.
Change into: 3 mm
Angle : 45 deg
Click OK
Create fillets on the edges
Select the green surfaces as shown in the picture.
Go to: Insert > Features > Fillet/Round > 1 mm
Click OK
-
8/9/2019 12. Engine
17/53
17 | P a g e
Select the MIDPLANE ENGINE
and create a new sketch
Draw the sketch as shownin the picture.
Create an extrude
Go to: Insert > Boss/Base > Extrude
Direction 1 : Midplane
Change into 150 mm
Click OK
Select the MIDPLANE ENGINE again
and create a new sketch
Draw the sketch as shown
in the picture.
Create an extrude
Go to: Insert > Boss/Base > Extrude
Direction 1 : Midplane
Change into 110 mm
Select the Selected bodies option.
Select the two cyan bodies
as shown in the picture.
Click OK
-
8/9/2019 12. Engine
18/53
18 | P a g e
Select the MIDPLANE ENGINE and create a new sketch
Draw the sketch as
shown in the picture.
Create an extrude
Go to: Insert > Boss/Base > Extrude
Direction 1 : Midplane
Change into 100 mm
Click OK
Select the green surface of Extrude10 and create a new sketch
Draw the square as shown in the picture.
-
8/9/2019 12. Engine
19/53
19 | P a g e
Create an extrude
Go to: Insert > Boss/Base > Extrude
Direction 1 : Blind
Change into 240 mm
Click OK
Create four chamfers
Go to: Insert > Features > Chamfer
Select the four green edges as shown in the picture.
Select for the Distancedistance option.
Change into: 30 mm
Change into: 240 mm
Click OK
Convert the four edges of the green surface
Select the green top surface of Extrude11
as shown in the picture.
Create a new sketch
Go to Tools > Sketch Tools > Convert Entities
Create an extrude
Go to: Insert > Boss/Base > Extrude
Direction 1 : Blind
Change into 125 mm
Click OK
-
8/9/2019 12. Engine
20/53
2 | P a g e
Create four chamfers
Go to: Insert > Features > Chamfer
Select the four green edges as shown in the picture.
Select for the Distancedistance option.
Change into: 90 mm
Change into: 15 mm
Click OK
Create sixteen fillets on the edges
Select the green edges as shown in the picture.
Go to: Insert > Features > Fillet/Round > 15 mm
Click OK
Create a new plane parallel at the green
surface
Go to: Insert > Reference Geometry > Plane
Select the green top surface of Extrude12 as shown in the picture.
Change the Offset Distance into 315mm.
Ensure that the offset is directed downwards.
If not, select Reverse direction
Click OK
-
8/9/2019 12. Engine
21/53
21 | P a g e
Select the new Plane4 and create a new sketch
Draw the two squares as shown in the picture.
Create an extruded cut
Go to: Insert > Cut > Extrude
Direction 1 : Blind
Change into 8 mm
Ensure that the offset is directed upwards.
If not, click Reverse direction
Click OK
-
8/9/2019 12. Engine
22/53
22 | P a g e
Create fillets on the edges
Select the four green edges as shown in the picture.
Go to: Insert > Features > Fillet/Round > 10 mm
Click OK
Create a linear pattern
Go to: Insert > Pattern/Mirror > Linear Pattern
Select an edge that lies parallel at the direction of the pattern.
This could be the green line as shown in the picture.
Change into: 16 mm
Number of Instances : 14
Features to pattern : Extrude13, Fillet4
Click OK
Create fillets on the edges of Extrude13
Select the green surfaces as shown in the picture.
Go to: Insert > Features > Fillet/Round > 2 mm
Click OK
-
8/9/2019 12. Engine
23/53
23 | P a g e
Select the MIDPLANE ENGINE and
create a new sketch
Draw the arc as shown in the picture.
Create a thin extruded cut
Go to: Insert > Cut > Extrude
Direction 1 : Midplane
Change into Trough All
Change into Trough All
Select the Thin feature option.
Direction : One-Direction
Change into 0,5 mm
Ensure that the extrusion is
directed upwards.
If not, click Reverse direction
Click OK
Bodies to Keep: Select All bodies
Click OK
The body is now divided into two parts
-
8/9/2019 12. Engine
24/53
24 | P a g e
Create fillets on the green edges
Select the green edges as shown in the picture.
Go to: Insert > Features > Fillet/Round > 10 mm
Click OK
Create fillets on the green edges
Select the green edges as shown in the picture.
Go to: Insert > Features > Fillet/Round > 5 mm
Click OK
Create four fillets on the green edges
Select the four green edges as shown in the picture.
Go to: Insert > Features > Fillet/Round > 8 mm
Click OK
Select the green surface of Chamfer3 and
create a new sketch
Draw the sketch as shown in the picture.
-
8/9/2019 12. Engine
25/53
25 | P a g e
Create an extrude
Go to: Insert > Boss/Base > Extrude
Direction 1 : Blind
Change into 2 mm
Click OK
Create four fillets on the green edges
Select the four green edges as shown
in the picture.
Go to: Insert > Features > Fillet/Round
> 10 mm
Click OK
Create a dome
Go to: Insert > Feature > Dome
Select the green surface of Extrude15.
Change the Distance into 2,5 mm
Turn of the Continuous dome option.
Click OK
Create a mirror
Go to: Insert > Pattern/Mirror > Mirror
Mirror Face/Plane : MIDPLANE ENGINE
Select the Features to Mirroroption
Features to Mirror : Extrude15, Fillet9, Dome2
Click OK
-
8/9/2019 12. Engine
26/53
26 | P a g e
Select the MIDPLANE ENGINE and create a new sketch
Draw the sketch as shown in the picture and detail.
Connect the construction line with the green
edge of Chamfer3.
Detail
Create an extrude
Go to: Insert > Boss/Base > Extrude
Direction 1 : Mid Plane
Change into 20 mm
Click OK
Create six fillets on the green edges
Select the green edges as shown in the picture.
Go to: Insert > Features > Fillet/Round > 10 mm
Click OK
Create another six fillets on the green edges
Select the green edges as shown in the picture.
Go to: Insert > Features > Fillet/Round > 2,5 mm
Click OK
-
8/9/2019 12. Engine
27/53
27 | P a g e
Create a mirror
Go to: Insert > Pattern/Mirror > Mirror
Mirror Face/Plane : Right Plane
Select the Bodiesto Mirroroption
Bodies to Mirror : Select the green body
Click OK
Create a fillet on the green edge
Select the green edge as shown in the picture.
Go to: Insert > Features > Fillet/Round > 25 mm
Click OK
Create two fillets on the green edges
Select the green edges as shown in the picture.
Go to: Insert > Features > Fillet/Round > 4 mm
Click OK
Select the green surface as shown in the picture
and create a new sketch
-
8/9/2019 12. Engine
28/53
28 | P a g e
Draw the sketch as shown in the picture.
Mirror the rectangle around the green construction line.
Mirror the two rectangles around the green construction line.
-
8/9/2019 12. Engine
29/53
29 | P a g e
Create an extrude
Go to: Insert > Boss/Base > Extrude
Direction 1 : Blind
Change into 50 mm
Click OK
Select the green surface as shown in
the picture and create a new sketch
Draw the four rectangles in the same way
as the previous rectangles.
Create an extrude
Go to: Insert > Boss/Base > Extrude
Direction 1 : Blind
Change into 12 mm
Click OK
-
8/9/2019 12. Engine
30/53
3 | P a g e
Create fillets on the green edges
and surfaces
Select the green edges and surfaces
as shown in the picture.
Go to: Insert > Features >
Fillet/Round > 5 mm
Click OK
Create fillets on the green edges
Select the green edge
as shown in the picture.
SolidWorks automatically selects the
other edges of this body.
Those are marked in yellow.
Go to: Insert > Features >
Fillet/Round > 2 mm
Click OK
Select the green surface as shown in
the picture and create a new sketch
Draw the circle.
-
8/9/2019 12. Engine
31/53
31 | P a g e
Create an extrude
Go to: Insert > Boss/Base > Extrude
Direction 1 : Blind
Change into 85 mm
Click OK
Create a new sketch on the front surface
of the new Extrude19
Draw the sketch as shown in the picture.
Create an extrude
Go to: Insert > Boss/Base > Extrude
Direction 1 : Blind
Change into 15 mm
Click OK
Create two chamfers
Go to: Insert > Features > Chamfer
Select the two green edges as shown in
the picture.
Select the Angledistance option.
Change into 4 mm
Angle : 45 deg
Click OK
-
8/9/2019 12. Engine
32/53
32 | P a g e
Create a new sketch on the green front surface
of the new Extrude20
Draw the sketch as shown in the picture
and detail.
Detail
Create an extruded cut
Go to: Insert > Cut > Extrude
Direction 1 : Up To Next
Click OK
Create two fillets on the green edges
Select the two green edges as shown in the picture.
Go to: Insert > Features > Fillet/Round > 2,2 mm
Click OK
-
8/9/2019 12. Engine
33/53
33 | P a g e
Create a circular pattern
Go to: Insert > Pattern/Mirror > Circular Pattern
Pattern Axis : Select the green surface as shown
in the picture.
Total Angle : 360 deg
Number of instances : 21
Select the Equal Spacing option.
Features to Pattern : Extrude21, Fillet16
Select the Geometry Pattern option.
Select the Propagate Visual Properties option.
Click OK
Create a chamfer
Go to: Insert > Features > Chamfer
Select the green edge as shown in
the picture.
Select the Distancedistance option.
Change into: 24 mm
Change into: 75 mm
Click OK
Create another chamfer
Go to: Insert > Features > Chamfer
Select the green edge as shown in
the picture.
Select the Angledistance option.
Change into 5 mm
Angle : 45 deg
Click OK
-
8/9/2019 12. Engine
34/53
34 | P a g e
Create a new plane parallel at the green surface
Go to: Insert > Reference Geometry > Plane
Select the green surface as shown in the picture and detail.
Change the Offset Distance into 10 mm.
Ensure that the offset is directed to the middle
of the body.
Select the Reverse directionoption.
Click OK Detail
Create a new sketch on the new
Plane5
Draw the sketch as shown inthe picture.
Connect the top of the vertical
construction line with the
green edge of Mirror2.
Close the sketch.
-
8/9/2019 12. Engine
35/53
35 | P a g e
Create a new sketch on the MIDPLANE ENGINE
Draw the arc as shown in the picture and detail.
Start the center point of the arc at the origin.
Close the sketch. Detail
Create a sweep
Go to:Insert > Boss/Base > Sweep
Profile : Select the green Sketch25
Path : Select the pink Sketch26
Click OK
Create a new sketch on the MIDPLANE ENGINE
Draw the circle as shown in the picture.
Connect the bottom of the vertical construction
line at the origin.
Close the sketch.
-
8/9/2019 12. Engine
36/53
36 | P a g e
Create a new plane parallel at the Top Plane
Go to: Insert > Reference Geometry > Plane
Select the Top Plane.
Change the Offset Distance into 350 mm.
Ensure that the offset is directed to above.
If not, select Reverse direction
Click OK
Create a sketch on the new Plane6
Draw the two lines as shown in the left picture.
Select the two lines and create a sketch fillet as shown in the right picture.
Close the sketch.
Create a sweep
Go to:Insert > Boss/Base > Sweep
Profile : Select the green Sketch27
Path : Select the pink Sketch28
Click OK
-
8/9/2019 12. Engine
37/53
37 | P a g e
Create a new sketch on Plane6
Draw the sketch as shown in the picture.
Create a revolve
Go to:Insert > Boss/Base > Revolve
Axis of revolution : Select the green line as shown in the picture.
Click OK
Create fillets on the green edges
Select the green edges as shown
in the picture.
Go to: Insert > Features >
Fillet/Round > 5 mm
Click OK
-
8/9/2019 12. Engine
38/53
38 | P a g e
Create a new sketch on the
Top Plane
Draw the sketch as shown
in the picture.
Create an extruded cut
Go to: Insert > Cut > Extrude
Direction 1 : Offset From Surface
Change into 1 mm
Select the pink surface as shown
in the picture.
Select the Reverse offset option.
Select the Translate surface option.
Click OK
Create a circular pattern
Go to: Insert > Pattern/Mirror > Circular Pattern
Pattern Axis : Select the green surfaceas shown in the picture.
Total Angle : 360 deg.
Number of instances : 30
Select the Equal Spacing option.
Features to Pattern : Extrude22
Click OK
-
8/9/2019 12. Engine
39/53
39 | P a g e
Create a new sketch on the green surface of Chamfer3
Draw the sketch as shown in the picture.
Close the sketch.
Create a new plane perpendicular
at the green surface
Go to: Insert > Reference Geometry
> Plane
Select the green surface.
Select the green horizontal
construction line of Sketch31.
Select an angle of 90 degrees.
Click OK
Select the new Plane7 and create a new sketch
Draw the two lines as shown in the picture and first detail.
Fix the horizontal line with the circle center of Skecth31.
Add a Sketch Fillet with a dimension of 27,5 mm.
Close the sketch. Details
-
8/9/2019 12. Engine
40/53
4 | P a g e
Create a sweep
Go to:Insert > Boss/Base > Sweep
Profile : Select the green circle of Sketch31
Path : Select the pink line of Sketch32
Click OK
Create a new sketch on the MIDPLANE ENGINE
Draw the sketch as shown in the picture.
Close the sketch.
-
8/9/2019 12. Engine
41/53
41 | P a g e
Make Sketch33 visible
Select Sketch33 in the toolbar > Right mouse click > Show
The sketch is visible now.
Create a new sketch on the Top Plane
Connect the left side of the sketch with a vertical construction line to the grey end
point of Sketch33. Connect the right side of the sketch with the midpoint of Sweep3.
Create a projected curve
Go to:Insert > Curve > Projected
Selections : Sketch33 and Sketch34
Click OK
-
8/9/2019 12. Engine
42/53
42 | P a g e
Select the green surface of Sweep3
and create a new sketch
Convert the two circles.
Close the sketch.
Create a sweep
Go to:Insert > Boss/Base > Sweep
Profile : Select the green circles of Sketch35
Path : Select the pink Curve1.
Click OK
Create a new sketch on the green surface of Mirror2
Draw the sketch as shown in the picture.
Close the sketch.
-
8/9/2019 12. Engine
43/53
43 | P a g e
Create a new plane perpendicular
at the green surface
Go to: Insert > Reference Geometry
> Plane
Select the green surface.
Select the green horizontal
construction line of Sketch36.
Select an angle of 90 degrees.
Click OK
Select the new Plane8 and create a new sketch
Draw the sketch on the same way as Sketch32.
Fix the horizontal line with the circle center of Skecth36.
Detail
Close the sketch.
Create a sweep
Go to:Insert > Boss/Base > Sweep
Profile : Select the green circle of Sketch36
Path : Select the pink line of Sketch37
Click OK
-
8/9/2019 12. Engine
44/53
44 | P a g e
Select the green surface of Sweep3 and create a new sketch
Convert the two circles.
Close the sketch.
Create a new sketch on the
MIDPLANE ENGINE
Draw the sketch as shown in the picture
and detail below.
Detail
-
8/9/2019 12. Engine
45/53
45 | P a g e
Make Sketch38 and Sketch39 visible
Select Sketch38 and Sketch39 in the
toolbar > Right mouse click > Show
The sketches are visible now.
Create a new sketch on the Top Plane
Draw the sketch as shown in the picture
and detail.
Connect the left side of the sketch with the
center point of Sweep5. Detail
Connect the right side of the sketch with a vertical
construction line to the grey end point of Sketch39.
Create a projected curve
Go to:Insert > Curve > Projected
Selections : Sketch39 and Sketch40
Click OK
-
8/9/2019 12. Engine
46/53
46 | P a g e
Create a sweep
Go to:Insert > Boss/Base > Sweep
Profile : Select the green circles of Sketch38
Path : Select the pink Curve2
Click OK
Create a new sketch on the MIDPLANE ENGINE
Draw the sketch as shown in the picture below.
-
8/9/2019 12. Engine
47/53
47 | P a g e
Create the green straight line as shown in the picture.
Close the sketch.
Make Sketch33 visible
Click on the before Sweep4 in the feature tree.
Click on the before Curve1
Select Sketch33 > Right mouse click > Show
-
8/9/2019 12. Engine
48/53
48 | P a g e
Create a new sketch on the Top Plane
Draw the sketch as shown in the picture and detail.
Pull at the blue arrow to change the shape of the spline.
Detail
Create the green straight line as shown in the picture.
Fix the vertical construction line at the left point of Sketch33.
Close the sketch.
-
8/9/2019 12. Engine
49/53
49 | P a g e
Create a projected curve
Go to:Insert > Curve > Projected
Selections : Sketch41 and Sketch42
Click OK
Create a sweep
Go to:Insert > Boss/Base > Sweep
Profile : Select the green circles of Sketch43
Path : Select the pink Curve3.
Click OK
Create a new sketch on the MIDPLANE ENGINE
Draw two green construction lines as shown in the detail.
Detail
-
8/9/2019 12. Engine
50/53
5 | P a g e
Draw the spline as shown in the picture.
Pull at the blue arrow to change the shape of the spline.
Create a thin extrude
Go to: Insert > Boss/Base >
Extrude
Direction 1 : Midplane
Change into: 8 mm
Select the Thin Feature option.
Direction: Midplane
Change into: 8 mm
Feature Scope: All bodies
Click OK
Create another sketch on the
MIDPLANE ENGINE
Draw two green construction lines
as shown in the detail.
-
8/9/2019 12. Engine
51/53
51 | P a g e
Draw the spline as shown in the picture.
Pull at the blue arrow to
change the shape of the spline.
Create a thin extrude
Go to: Insert > Boss/Base >
Extrude
Direction 1 : Midplane
Change into: 8 mm
Select the Thin Feature option.
Direction: Midplane
Change into: 8 mm
Feature Scope: All bodies
Click OK
Create fillets on the green edges
Select the eight green edges as shown in the picture.
Go to: Insert > Features > Fillet/Round > 3,99 mm
Click OK
-
8/9/2019 12. Engine
52/53
52 | P a g e
Create a new sketch on the Top Plane
Draw the sketch as shown in the picture
and connect the dimensions with the
origin.
Create an extruded cut
Go to: Insert > Cut > Extrude
Direction 1 : Trough All
Click OK
Create fillets on the green edges
Select the two green edges as shown in
the picture.
Go to: Insert > Features > Fillet/Round > 2 mm
Click OK
-
8/9/2019 12. Engine
53/53
Create fillets on the green edges
Select the two green edges as shown in
the picture.
Go to: Insert > Features > Fillet/Round > 0,5 mm
Click OK
Hide all planes and sketches except:
- MIDPLANE ENGINE
Save the file with the following name: Engine