11 conversion of timber
TRANSCRIPT
![Page 1: 11 conversion of timber](https://reader034.vdocuments.us/reader034/viewer/2022052205/55546e03b4c905aa798b54ab/html5/thumbnails/1.jpg)
WOOD MATERIALS TECHNOLOGY
4th Edition
![Page 2: 11 conversion of timber](https://reader034.vdocuments.us/reader034/viewer/2022052205/55546e03b4c905aa798b54ab/html5/thumbnails/2.jpg)
Chapter 11Conversion of Timber
![Page 3: 11 conversion of timber](https://reader034.vdocuments.us/reader034/viewer/2022052205/55546e03b4c905aa798b54ab/html5/thumbnails/3.jpg)
Felling Transporting
Felling timber
![Page 4: 11 conversion of timber](https://reader034.vdocuments.us/reader034/viewer/2022052205/55546e03b4c905aa798b54ab/html5/thumbnails/4.jpg)
Converting logs
Horizontal bandsaw Reasons to convert timber
Allows wood to dry fasterProvides wood of usable
size and shapeAllows the quality of the
timber to be seen
![Page 5: 11 conversion of timber](https://reader034.vdocuments.us/reader034/viewer/2022052205/55546e03b4c905aa798b54ab/html5/thumbnails/5.jpg)
Through and through sawingPlain/slash sawing
![Page 6: 11 conversion of timber](https://reader034.vdocuments.us/reader034/viewer/2022052205/55546e03b4c905aa798b54ab/html5/thumbnails/6.jpg)
Advantages– Low cost and fast– Maximum width of planks obtained from
log.– Little wastage.– Reveals attractive grain pattern,
especially in softwoods. Disadvantages
– Not suitable for structural timber– Some boards are all sapwood– With this method cupping caused by
tangential shrinkage is a problem (cupping is the warping of the plank away from the heart of the tree)
![Page 7: 11 conversion of timber](https://reader034.vdocuments.us/reader034/viewer/2022052205/55546e03b4c905aa798b54ab/html5/thumbnails/7.jpg)
Quarter sawingRadial/quarter sawing
![Page 8: 11 conversion of timber](https://reader034.vdocuments.us/reader034/viewer/2022052205/55546e03b4c905aa798b54ab/html5/thumbnails/8.jpg)
Advantages – An attractive grain
pattern is produced– Boards are more stable
and shrink less– Boards wear more
evenly,important for flooring
Disadvantage– Expensive, as the log
has to be first quartered then turned for every cut.
– Because the log is quartered then cut again narrower boards are produced
![Page 9: 11 conversion of timber](https://reader034.vdocuments.us/reader034/viewer/2022052205/55546e03b4c905aa798b54ab/html5/thumbnails/9.jpg)
Tangential sawing
![Page 10: 11 conversion of timber](https://reader034.vdocuments.us/reader034/viewer/2022052205/55546e03b4c905aa798b54ab/html5/thumbnails/10.jpg)
Advantages– Produce board with
flame figure– Tangential boards are
strong boards, used for beams and joists
– Heartwood and sapwood are easily separated
– These boards can take a nail without splitting because of the position of their annual rings
Disadvantages– Prone to shrinkage
(Cupping)– It is expensive as the log
is turned 90º for each cut
![Page 11: 11 conversion of timber](https://reader034.vdocuments.us/reader034/viewer/2022052205/55546e03b4c905aa798b54ab/html5/thumbnails/11.jpg)
Exam question
1 Shown in the diagram are two methods for timber conversion.
(a) Name the two methods of conversion shown in the diagrams.(b) State two advantages and two disadvantages of each method.(c) The diagrams show the ends of two boards, M and N. Which of
the boards is most likely to cup? Give a reason for your answer. Describe, using a neat freehand sketch, the direction of cupping.
(JC, HL, 2005)
![Page 12: 11 conversion of timber](https://reader034.vdocuments.us/reader034/viewer/2022052205/55546e03b4c905aa798b54ab/html5/thumbnails/12.jpg)
Sample answer to exam question
1 (a) The methods of conversion shown are:A Through and through sawing, also called slash or plain sawing.B Quarter sawing or radial sawing.
(b) Through and through sawingAdvantages
• There is very little waste from this method• It gives wide boards• It is a cheap and easy method
Disadvantages• The boards are prone to cupping• The boards have no particular grain pattern• There would be a lot of sapwood in many boards so more likely
to rot due to fungi and insects
![Page 13: 11 conversion of timber](https://reader034.vdocuments.us/reader034/viewer/2022052205/55546e03b4c905aa798b54ab/html5/thumbnails/13.jpg)
Sample answer to exam question
1 (b) Quarter sawingAdvantages
• The boards are stable• The boards are hard-wearing and used in flooring
Disadvantages• More labour required, as the logs need to be turned• More expensive• More waste produced
![Page 14: 11 conversion of timber](https://reader034.vdocuments.us/reader034/viewer/2022052205/55546e03b4c905aa798b54ab/html5/thumbnails/14.jpg)
Sample answer to exam question1 (c) The board most likely to cup is board M. This is because when
the wood begins to dry, the cells shrink. The shrinkage occurs along the rings, which tends to pull the board into a curved shape as a result. The other board, N, will have more even shrinkage because of the arrangement of the rings as shown.
![Page 15: 11 conversion of timber](https://reader034.vdocuments.us/reader034/viewer/2022052205/55546e03b4c905aa798b54ab/html5/thumbnails/15.jpg)