10’ x 20’ display booth - infinityexhibits.com€¦ · front poster side poster side poster...
TRANSCRIPT
10’ x 20’ Display Booth
Display Setup Instructions
Steps to Assemble the 20ft Fusion Display:
Step 1: Install the Carpet Padding and Vinyl Flooring.
Step 2: Assemble the Backwall and Header Signs.
Step 3: Install the Fluorescent Lighting and Fabric Graphic on the Center Section.
Step 4: Attach the Backwall Posters and Header Posters with Velcro.
Step 5: Attach the TV Monitors to the Back Posts.
Step 6: Attach the Stem Lights to the top of the frame.
Step 7: Assemble the Pedestals and place them along the backwall.
Step 8: Assemble the Counter and place it within the booth area.
Page 1
10’ x 20’ Display Booth
F-20-6-1_Ovation
20ft Fusion Trade Show Display BoothAssembly Instructions:
Page 2
Install the Carpet Padding and Vinyl Flooring.
A) Unroll the Carpet Padding within the Booth Area.
B) Install the Vinyl Flooring on top of the Carpet Padding.
F-20-6-1_Ovation
20ft Fusion Trade Show Display BoothAssembly Instructions:
(red)PH1035
(blue)VS76 (orange)TR45
(green)
(yellow)
PX4032 Ceiling Panel Support
Ceiling Panel Support
Back Post
(Front of Booth)
Center Section
Side Section
Side Section
(Back of Booth)
Booth Detail: Identify the Aluminum Components for the framwork.
LEGEND
Page 3
94”94”
94”
4”
16” 12” 4”
94”91½”
94”94”
94”
94”
15¼”
15¼”
15¼”
15¼”
76½”
76½”
76½”
76½”
76½”
76½”
76½”
Angled Support Leg
F-20-6-1_Ovation
20ft Fusion Trade Show Display BoothAssembly Instructions:
hex key
hex key
Lower Beam
Tension Lock
Tension Lock
Corner Post
View showing typical assembly of components
A) Components attach together using the Tension Locks and a hex key.
B) Assemble the Center Section along the backwall.
Opening
Assemble the Backwall and Header Signs.
Page 4
Assemble the Center Back Panels so that the openings for the power cords are in the bottom corner as shown. Also, make sure that the Velcro faces forward to attach the �uorescent lights.
CenterBack Panel
94”
15¼”
76½”
Slide the PVC Wall Panels into place along the inside tracks of the Posts and Beams.
Velcro on front of the Center Back Panels to attach the fluorescent lights.
Center Section
F-20-6-1_Ovation
20ft Fusion Trade Show Display BoothAssembly Instructions:
C) Slide the Ceiling Panel Supports into the inside tracks along the upper beams prior to assembly.
E) Attach the Wire Management Sections to the inside tracks at the front of the Center Section.
D) Place the Ceiling Panel on top of the Ceiling Panel Supports.
Opening
Page 5
The Wire Management snaps into place with pressure. Make sure that the Velcro faces forward.
Ceiling Panel Support
Ceiling Panel
Upper BeamCenter
Back Panel91½”94”
94”
94”
15¼”
15¼”
15¼”
15¼”
76½”
76½”
76½”
12”12”
12”
16”
16”
16”
16”
(Velcro on front of Back Panels)
Velcro on front of Wire Management
Center Section
Center Section
F-20-6-1_Ovation
20ft Fusion Trade Show Display BoothAssembly Instructions:
hex key
TOP VIEW
PR2 frictionlock
Panel Gripper
Panel Grippers lock into position using hex key, bolt, and PR2 friction lock.
Attach the Back Post halfway along the bottom brace at 38¼” from the Center Section as shown.
Strongbacks attach to the Panel Grippers with the nylon threaded screws.
PanelGripper
(Front of Booth)
Center Section
Side Section
4”
4”76½”
38¼”
Angled Support Leg
Nylon Set Screw
Page 6a
Strongback
Strongback
Strongback
94”
F) Assemble the Side Sections to the Center Section. Begin by attaching the Back Posts.
G) Attach the Strongbacks to the back posts.
H) The Strongbacks attach to the back posts using the Panel Grippers and Nylon Set Screws.
Back Post Back Post
Back Post
Back Post
F-20-6-1_Ovation
20ft Fusion Trade Show Display BoothAssembly Instructions:
Side Section
76½”
Page 6b
Top Brace
I) Attach the top brace to the top of the Back Post and Center Section.
J) Slide the Side Back Panels into place along the inside tracks.
SideBack Panel Side
Back Panel
Opening for Monitor Mount
Velcro on front of PVC Panels for Laminated Posters. (The posters may be preattached).
Seam
Pull back the Side Back Panels together in the middle to properly align and attach them to the Strongbacks with Velcro along the seam.
View showing Side Back Panels attached to the Strongbacks in the back of the booth.
Strongback
Strongback
Side Back PanelSide
Back Panel SideBack Panel
K) Attach the Side Back Panels to the Strongbacks along the seam with Velcro.
Opening for Monitor Mount
F-20-6-1_Ovation
20ft Fusion Trade Show Display BoothAssembly Instructions:
Page 7
Install the Lower Header Beam at 14½” from the top of the Post
Lower Header BeamHeader Panel
Post
94”94”
15¼”
15¼”
14½”
76½”
76½”
M) Assemble the Header Sections.
L) Attach the End Sections.
N) Slide the Header Panels down into position from the top.
(Velcro on front of Header Panel)
Side Section Side Section
F-20-6-1_Ovation
20ft Fusion Trade Show Display BoothAssembly Instructions:
A) Attach the Fluorescent Lights along the center backwall panels with Velcro and attach them in series.
B) Unfold the Fabric Graphic and attach to the frame with Velcro.
Install the Fluorescent Lighting and Fabric Graphic along the Center Section.
Page 8
Fabric Graphic
Fluorescent Light
Fluorescent Light
Link CableLink Cable
Link Cable
Power Cable Power Cable
Velcro
Attach the Fabric Graphic starting at the top left corner and roll downward keeping the top edge aligned with the top of the frame.
F-20-6-1_Ovation
20ft Fusion Trade Show Display BoothAssembly Instructions:
Page 9
Header Poster
A) Attach the backwall posters to the back PVC panels so that they abut together at the inside seams (if they are not already attached to the PVC panels).
B) Attach the Header Posters to the Header Panels with Velcro.
Attach the Laminated Backwall Posters and Laminated Header Posters with Velcro.
Backwall Poster
F-20-6-1_Ovation
20ft Fusion Trade Show Display BoothAssembly Instructions:
Page 10
Use two (2) people or more when attaching the LED Monitor to the Back Post.
Monitor Mount attached to LED Monitor
A) Attach the Monitor Mounts to the back of the LED Monitors with bolts.
B) Attach the Monitor Mounts to the Back Posts with Tension Locks and hex key.
Attach the TV Monitors to the Back Posts.
hex key
bolts
Back Post
Back Post
Monitor Mount
Monitor Mount
Monitor MountLED Monitor LED Monitor
LED Monitor
TOP VIEW TOP VIEW
F-20-6-1_Ovation
20ft Fusion Trade Show Display BoothAssembly Instructions:
Attach the Stem Lights to the top of the frame.
Secure Lights to top of frame with thumbscrews.
View shows typical connection of lights to power source in the back of the booth.
A) Place Lights at desired locations and secure with thumbscrews.
B) Connect Lights to power source.
Page 11
Stem Light
F-20-6-1_Ovation
20ft Fusion Trade Show Display BoothAssembly Instructions:
LEGEND
Back PanelAssembly
Back PanelAssembly
Front PanelAssembly
Front PanelAssembly
Counter
Pedestal
Counter Components
Pedestal Components
Side Panel
Side Panel
Side Panel
Counter Top
Side Panel
Middle Shelf
Middle Shelf
Page 12
Assemble the Counter and Pedestals.
A) Counter Components are marked with a blue dot ( ) and the Pedestal Compontents are marked with a pink dot ( ).
Pedestal Top
(There are two (2) Pedestals included with this Display Booth)
F-20-6-1_Ovation
20ft Fusion Trade Show Display BoothAssembly Instructions:
Step 1: Attach the Bottom Braces to the Front and Back Panel Assemblies with the Tension Locks and hex key.
Step 2: Slide one of the Side Panels into the frame.
Back PanelAssembly
Back PanelAssembly
Front PanelAssembly
Front PanelAssembly
Bottom Brace
Tension Lock
Bottom Brace
Side Panel
Page 13
NOTE: Bottom Braces do not have Velcro attached.
Assembly method for the Counters and Pedestals:
F-20-6-1_Ovation
20ft Fusion Trade Show Display BoothAssembly Instructions:
Step 3: Place the Shelf onto the Shelf Brackets. (Attach the Shelf Brackets along the interior tracks of the Front and Back Panel Assemblies if they are not already attached. Also, adjust the heights of the Shelf Brackets as desired.)
Step 4: Slide the second Side Panel into the frame.
Back PanelAssembly
Back PanelAssembly
Front PanelAssembly
Front PanelAssembly
Shelf
Shelf Bracket
Side Panel
Page 14
View showing Shelf Bracket installed along track.
F-20-6-1_Ovation
20ft Fusion Trade Show Display BoothAssembly Instructions:
Page 15
Step 5: Attach the Top Braces to the frame.
Step 6: Attach Counter Top to frame with Velcro.
Step 7: Attach Posters to PVC Panels with Velcro.
hex key
Tension Lock
Front Poster
Side Poster
Side PosterCounter Top
Secure the Top Braces with hex key and Tension Locks.Top Braces have Velcro
attached to the top.Top Brace
F-20-6-1_Ovation
20ft Fusion Trade Show Display BoothAssembly Instructions:
Pack the wooden crate with the booth components in the following manner:
Crate (packed)
Crate Layout
Counter Tops, Pedestal Tops & Shelves
PVC Panels
Posters
Large Aluminum Components Pedestal Assemblies
Counter Assemblies
Stools
Fluorescent Lights
Stem Lights Electrical Cords
LED
TV
LED
TV
Fabric Graphic
Tools KeysMisc. Hardware
Strongbacks
Wire Management
48”h (ID)
(not to scale)
up
98”w (ID)
FRONT VIEW
NOTE: Separate Layers of components with sheets of cardboard to protect the booth components.
Page 16
Carpet Padding
Vinyl Flooring
Small Aluminum Components
F-20-6-1_Ovation
20ft Fusion Trade Show Display BoothAssembly Instructions: