1065 zone 2 - yamaha corporation€¦ · tv bd/dvd player cable/satellite box rx-v1065 zone 2...
TRANSCRIPT
TV
BD/DVD player Cable/Satellite Box
RX-V1065 Zone 2 Hookup Example
Zone 2
PR
EPAR
ATION
BAS
IC
OP
ER
ATION
DOCK
PHONOCOMPONENT
VIDEO
PR
PB
Y
OPTICAL( TV )AV 1 AV 2
COAXIAL
AV 3(CD)
COAXIAL OPTICAL
AV 4 AV 5 AV 6AV
OUT AUDIO1 AUDIO2FRONT SURROUND SUR.BACK SUBWOOFER
MULTI CH INPUTAUDIOOUT
ZONE2OUT
FRONT SURROUND SUR. BACK SUBWOOFER
PRE OUT
CENTERSINGLE
VIDEO
GND
ANTENNA
UNBAL.
FMHD Radio GND AM
VIDEO
IN
OUT
MONITOR OUT SPEAKERS
TRIGGER OUT
12V0.1A MAX. FRONT CENTER
SINGLE CLASS 2 WIRING
SURROUND SURROUND BACK/BI-AMP
EXTRA SP ZONE2/PRESENCE
1 2
CENTER
PR
PB
Y
REMOTE
COMPONENTVIDEO
SIRIUS XM HDMI(BD/DVD)
OUT HDMI 2 HDMI 3 HDMI 4HDMI 1
TRIGGER OUT
OUTHDMI
INHDMI
Analog Output
OUTHDMI
OUTHDMI
Analog Output
Audio 1 Input
Audio 2Input
IN 1HDMI HDMI
IN 2
To select the Cable/Satellite Box as asource for Zone 2, the Audio 2 inputon the receiver must be selected in
NOTE:
To select the BD/DVD player as asource for Zone 2, the Audio 1 inputon the receiver must be selected in
NOTE:
Zone 2. Zone 2
Extra SPZone 2/ PresenceSpeaker Terminal
Zone 2 setup on the RX-V1065 using the Internal Power Amp
The RX-V1065 Extra Speaker Terminals can power one set of speakers for Zone 2 or Presence speakers. If the Extra Speaker Terminals are utilized then the RX-V1065 cannot be set for 7.1 (Surround Back terminals.) or Bi Amp (Surround Back terminals.)
Setting the Extra Speaker Terminals Note: The RX-V1065 remote control will be used to access the Setup Menu of receiver.
1. Press the On Screen button on the remote control to enter the. 2. Scene BD/DVD will come up on the receiver LED Screen. 3. Arrow down to until Setup comes up in the receiver LED Screen. 4. Press the Enter Button on the remote control. 5. Setup/Speaker Setup will come up on the receiver LED Screen. 6. Press the Enter Button on the remote control. 7. SP Set/1. Auto Setup will come up on the receiver LED Screen. 8. Arrow down until 2 Manual Setup comes up in the receiver LED Screen. 9. Press the Enter Button on the remote control. 10. SP/Set, A) Config will come up on the receiver LED Screen. 11. Press the Enter Button on the remote control. 12. Config, Extra………None will come up on the receiver LED Screen. 13. Use the Left/Right Arrow buttons on the remote to change the Extra to: Extra……….Zone2. 14. Use the Return and Setup buttons on the remote to exit the Setup Menu. 15. Extra Speaker setup is complete.
To control Zone 2 using the RX-V1065 remote the switch at the upper most left hand corner of the remote must be set to Zone 2. Once the remote has been set to Zone 2 the following commands will be available:
1. Selecting the input source (AV5-6, AUDIO1-2, and V-AUX) of Zone 2. 2. Adjusting the volume of Zone 2 (when a Zone 2 speaker is connected to the EXTRA SP jack). 3. Tuning into FM or AM when “TUNER” is selected as the input source of Zone 2 (see page 29 of
the owner’s manual). 4. Tuning into XM Satellite Radio when “XM” is selected as the input source of Zone 2 (see page
33) (U.S.A. model only). 5. Tuning into SIRIUS Satellite Radio when “SIRIUS” is selected as the input source of Zone 2
(see page 37) (U.S.A. model only). 6. Playing back music stored on your iPod stationed in a Yamaha iPod universal dock (such as
YDS-10, YDS-11 and YDS-12 sold separately) connected to the DOCK terminal. Note: Only Analog signals can be sent to Zone 2. If you want to output the sound from Zone 2, connect an external component to AV 5-6 or Audio 1-2 by analog connection. Important Safety Notice: The EXTRA SP Speaker Terminals of this unit should not be connected to a Passive Loudspeaker Selector Box or more than one Loudspeaker per Channel. Connection to a Passive Loudspeaker Selector Box or Multiple Speakers per channel could create an abnormally low impedance load resulting in amplifier damage.