1 of 4 quick start guide - security brands, inc

1 Carefully unpack box.

1 of 4

We recommend mounting Ascent X1 on astandard gooseneck pedestal.

If using alternate mounting, the optionalAscent 10' Cable Extension (p/n 16-X-EXT)must be purchased. Follow the instructions

included with the extension before moving on. Failure to do so may result in no signal!

IMPORTANT!r

Copyright © Security Brands, Inc. QSG-16X1-EN Rev. D (12/2015)

START HERE

2 Unlock and open front panel of unit for access to internal components.

QUICK START GUIDE

What’s what?All the important components labeled for you.

Camera kit mounting locationCamera kit sold separately.

Terminal blockFor wiring to gate operator

or door operner

Antenna cable

Reset button and terminals for performing hard reset

SIM cardIf you have your own SIM card, see page 4 and follow the instructions entitledInstalling Custom SIM Card.

Speaker connectorSpeaker can be disconnected temporarilyif unit is intermittently beeping. This is usually due to a SIM card that is not yet activated.

WARNING!AUTOMATIC GATES CAN CAUSE

SERIOUS INJURY OR DEATH!

ALWAYS CHECK that the GATE PATH IS CLEAR BEFORE OPERATING!

Reversing or other safety devices should ALWAYS BE USED!

Continued on next page...

Unit shown with front panel fully open.Internal wiring not shown for clarity.

IMPORTANT!r

Ascent X1 WILL NOT WORK until the activation process has been completed!

Follow the Activation Guide or callSummit Control at (844) 259-8265 to

activate your unit.

2 of 4QUICK START GUIDE

4 Close and lock front panel. 5 Make sure gate path is clear, then key in temporary code 2012 on keypad and confirm gate opens.

Now follow the Activation Guide to create an account and begin using Ascent.

INSTALLATION COMPLETE!

N

3 Connect wiresFeed wires through back of unit and connect as shown.

STATUS POWER EVENTRELAY A RELAY B

Ascent X1 Terminal Block

N/O

GND

POS.

(+)

NEG.

(–)

N/O

COM

N/C

N/O

COM

N/C

COM

N/O

POWER 12–24 VAC/VDC

Gate Operator / Door Opener

POS.

(+)

NEG.

(–)

COM

RADI

O

COM

FREE

EXIT

COM

REVE

RSE L

OOP

COM

OPEN

STOP

CLOS

E

12–24 VAC/VDC

Third-Party 12–24-V AC/DCPower Source

Relay B can be wired to asecond device in the same manner.

+ –

OR

Supplied 12-VACTransformer

Before proceeding,double check that wiring is correct and unit has power!

For additional wiring options, see page 3.

STOP!

If you will not be using the supplied 12-VAC transformer, please go to page 4 and follow the procedure, Using a Third-Party Power Source.

Do not exceed 24 VAC/VDC! Failure to choose a compatible power source can damage unit!

CAUTION!


POWER 12–24 V AC/DC

Gate Operator / Door Opener

POS.

(+)

NEG.

(–)

COM

RADI

O

COM

FREE

EXIT

COM

REVE

RSE L

OOP

COM

OPEN

STOP

CLOS

E


A Status CheckWiring to enable device status check

B Open/Close ModeWiring when not using gate operator’s “timer-to-close” function.



N/O

GND

POS.

(+)

NEG.

(–)

N/O

COM

N/C

N/O

COM

COM

N/C

COM

N/O

12–24 V AC/DC

Connected as shown in Step 3

(If equipped with limit switches)

Close Limit Switch

Open Limit SwitchOptional

wire splices

N/O

N/C

COM

N/O

N/C



N/O

GND

POS.

(+)

NEG.

(–)

N/O

COM

N/C

N/O

COM

N/C

COM

N/O

12–24 V AC/DC

Connected as shown in Step 3

Gate Operator

IMPORTANT!rOpen/Close Mode will only work if the device is set to that mode

from the Device Settings page in the Admin Area!You CANNOT log in until account activation has been completed!




3a Connect wires to unit as shown in Step 3.

3b Connect wires to your power source, making sure you connect positive to positive and negative to negative.

CAUTION!

Double check that you’ve wired from positive on Ascent X1 to positive on your power source and negative on Ascent X1

to negative on your power source.

Reverse polarity can damage Ascent!

1 Slide SIM card holder in OPEN direction and lift to swing open. 2 Remove existing SIM card and install

new SIM card. 3 Swing cover back down completely and slide in CLOSE direction to lock.

InstallingCustomSIM Card(Optional)

Using aThird-PartyPower Source(Optional)

IMPORTANT!rIf you would like to use a third-party

power source, such as solar, verify thatit conforms to the following specs:

Input 12–24 VAC / VDCmust be within ±10%

Current Draw less than 100 mA @ 12 VDCless than 75 mA @ 24 VDC

? Contact us at (844) 259-8265or visit summitcontrol.com/contactNEED HELP?

1 of 4 quick start guide - security brands, inc

Documents