1 |

INALA TECHNOLOGIESINSTALLATION TRAINING: ECS (EQUIPMENT COMMUNICATIONS SYSTEM) ECS (ETH/E1) COMMISSIONING

VERSION 1.0

2 |

ECS (ETH/E1) COMMISSIONINGCOMMISSIONING: ECS (ETH/E1) PROCEDURE

3 | SAM Training

ECS (ETH / E1) - COMMISSIONING

Setting up of the unit:• Power unit on• Connect using the ITMS ECT• Set-up the communication ports for the devices you are connecting to it• Set-up the Sever IP address • Click on set after making a change to save the configuration to the unit.• Call to commission site with representative.

Port Settings• SAM1.5 = Physical port 8 – Virtual Port 310, Baud rate 19200.• L&G = Physical port 10 – Virtual Port 309, Baud rate 19200• SAM2 & Access Control = Physical port RS485 – Virtual Port 301, Baud

rate 9600

ECS (E1/Eth) Communication Cable:• A “Straight RS232” cable must be used between the ECS-L and the computer.

(DB9 to IDC 10Way)• Once Connected open the “ITMS-C ECT” software.• Input User Name and Password, select “Serial Communication) and Click on

Login

*Note – Check following slide for detail information of above procedure

4 | SAM Training

ECS (ETH / E1) – PHYSICAL PORT NUMBERS

SP6 pluggable moduleEquipment Communications Controller (ECS)

RS485 Port

Port 1 – RS232

Port 10 – RS485

Port 9 – RS485 Port 8 – RS232

Port 7 – RS232

Port 6 – RS232 Port 5 – RS232

Port 4 – RS232

Port 3 – RS232

* The physical port that is connected to the SAM or Access Control must be selected as the

“UDP PORT”

Earth48vdc G

ND

5 | SAM Training

SOFTWARE FOR FULL ECS(ETH/E1) (EQUIPMENT COMMUNICATION CONTROLLER)

Communication Controller Software (ECT):ECT Version is viewed on the top left corner as indicated with the yellow circleEG: “ITMS-C Ver 2.12”

Firmware Version is viewed on the button left corner as indicated with the Red circleEG: “S/W: 4.0.1.4”

Set IP addresses as received from operator as indicated in the blue circle. After IP addresses has been completed, click on set to save them to the communications controller

6 | SAM Training

SOFTWARE FOR FULL ECS(ETH/E1) (EQUIPMENT COMMUNICATION CONTROLLER) – PORT SETUP

Port Set UP:The ports should be set-up as per the screen shot for a standard Vodacom BTS site.PORT - This is the physical port on the unitPort No. - This is the virtual port number allocated to a specific devicePort Name – You are able to label the port with the device you have connected to it.Baud rate – Select the appropriate baud rate for the deviceFlow Control – select the appropriate flow control for the deviceProtocol – Select the appropriate protocol for the device

Physical Port Type of PortRS485 Port RS485Port 1 RS232Port 3 RS232Port 4 RS232Port 5 RS232Port 6 RS232Port 7 RS232Port 8 RS232Port 9 RS485Port 10 RS485

7 | SAM Training

EQUIPMENT COMMUNICATION CONTROLLER – PORT & SERVER ALLOCATIONS

Virtual Port Allocations

301 SAM2 or SAM3 and Access Control

302 Rectifier A

303 Rectifier B

304 Generator

305 AVR

306 BMON

307 Fuel Cell 1308 Fuel Cell 2

309 Energy Meter / Fire System310 SAM 1.5 REC

Vodacom Server Name Vodacom UDP Server IP UDP Server Port

ZABLV06101 - CEN 10.121.5.165 299

ZABLV06102 - EAS 10.121.5.153 299

ZABLV06103 - LIM 10.121.5.154 299

ZABLV06104 - MPU 10.121.5.155 299

ZABLV06105 - SGC 10.121.5.156 299

ZABLV06106 - SGS 10.121.5.157 299

ZABLV06107 - WES 10.121.5.158 299

NGA Existing Server 10.102.242.202 299

Telkom Server Name Telkom UDP Server IP UDP Server Port

10.149.104.56 2999

Neotel Server Name Neotel UDP Server IP UDP Server Port

172.24.146.4 299

Operator Name APN Name

Vodacom Vodameter

Neotel internet

8 | SAM Training

EQUIPMENT COMMUNICATION CONTROLLER – COMS WIRINGCommunication Cable Consumables

ECS (Eth/E1), ECS-L

1. 10 way Ribbon Cable2. 10 way IDC connector for 10 way ribbon cable3. DB9 IDC, male and female for 10 way ribbon cable

ECS (Eth/GPRS), ECS (Eth/E1) & ECS-L

1. DB9, male and female, solder type2. Milar cable used with point 1 above (Same as SAM2 Coms cross over cable)

ECS (Eth/GPRS), ECS (Eth/E1) & ECS-L

1. RJ9 – small 4 way2. RJ11 – large 4 way3. RJ12 - 6 way4. RJ45 – 8way5. Cable for each above6. CAT5 cable

Possible Communication Cables needed

1. SAM1.52. SAM2, SAM3 & Access Control3. Energy Meter (Landis & Gyrr) Rectifier4. Rectifier (Battery Tech, Grintek, ASM, etc)5. Generator (Lovato, Deep Sea, Intellilite, etc)6. Fuel Cell (Idatech, Gencore, etc)

9 | SAM Training

ECS (ETH/E1) COMMUNICATION WIRINGSAM2 & ACCESS CONTROL

10 | SAM Training

ECS (ETH/E1) COMMUNICATION WIRINGSAM1.5

11 | SAM Training

ECS (ETH/E1) COMMUNICATION WIRINGLANDIS & GYRR

12 | SAM Training

ECS (ETH/E1) COMMUNICATION WIRINGBATTERY TECH SM50

13 | SAM Training

ECS (ETH/E1) COMMUNICATION WIRINGBATTERY TECH SM65

14 | SAM Training

ECS (ETH/E1) COMMUNICATION WIRINGGRINTEK GT500

15 | SAM Training

ECS (ETH/E1) COMMUNICATION WIRINGDEEP SEA

16 | SAM Training

ECS (ETH/E1) COMMUNICATION WIRING LOVATO

17 |

CLICK TO EDIT MASTER TITLE STYLE

THANK YOU