1. hdd partition setup insert booting diskette to a: drive and turn on the power. then it will be...
TRANSCRIPT
1. HDD Partition Setup
Insert Booting Diskette to A: drive and turn on the power.
Then it will be boot by floppy diskette.
1
Type FDISK and press Enter key2
Why does DVR have to be divided partition in Hard disk.
▶ As DigiNet save data to Hard disk, DVR is not overwrite to Hard disk but automatically format
drive and save data to Hard disk.
1. After installing DVR and perform DVR at the beginning, format drive D and save data.
2. Automatically format drive E, if D drive is full.
3. Rest of the drive will be proceeded as same as No.2
4. If Hard drive is full, automatically format drive D again and save data and previous data will not
be existed.
▶ Therefore, each partition of drive will be divided as possible as small size(1~2GB), but is need for
your attention, if you have plan to add Hard disk.
▶ Each saving data drive will be divided from D to Y maximally
If it is included backup system, the system will be required a drive, so last two drives will
be made for backup.
Microsoft(R) Windows 98
(C) Copyright Microsoft Corp 1981-1999
A:\>
A:\>FDISK
This is the example of “FDISK” when 20GB Hard is installed.
HDD Size is over 2GB, so press Enter key 3
You computer has a disk larger than 512 MB. This version of Windows
includes improved support for large disks. Resulting in more efficient
use of disk space on large drivers, and allowing disks over 2 GB to be
IMPORTANT : If you enable large disk support and create any new drives on this
Disk, you will not be able to access the new drive(s) using other operating
system, including some versions of Windows 95 and Windows NT, as well as
earlier versions of Windows of Windows and MS-DOS. In addition, disk utilities that
Were not designed explicitly for the FAT32 files system will not be able
To work with this disk. If you need to access this disk with other operating
systems or older disk utilities, do not enable large drive support.
Do you wish to enable large disk support (Y/N)……………………..….? [Y]
Should be created Dos partition is Logical Dos drive, so press Enter key4
Microsoft Windows 98
Fixed Disk Setup Program
(C) Copyright Microsoft Corp. 1983 – 1998
FDISK Options
Current fixed disk drive : 1
Choose one of the following:
1. Create DOS partition or Logical DOS Drive
2. Set active partition
3. Delete partition or Logical DOS Drive
4. Display partition information
5. Change current fixed disk drive
Enter choice : [1]
Press Esc to exit FDISK
First, it should be created primary Dos partition.5
Create DOS Partition or Logical DOS Drive
Current fixed disk drive : 1
Choose one of the following :
1. Create Primary DOS Partition
2. Create Extended DOS Partition
3. Create Logical DOS Drive(s) in the Extended DOS Partition
Enter choice : [1]
Press Esc to return to FDISK Options
Create Primary DOS Partition
Current fixed disk drive : 1
Verifying drive integrity, 10% Complete.
Create Primary DOS Partition
Current fixed disk drive : 1
Do you wish to use the maximum available size for a Primary DOS Partition
(Y/N)………………………………………………………………….? [Y]
Press Esc to return to FDISK Options
Check to drive
Create Primary DOS Partition
Current fixed disk drive : 1
Total disk space is 19571 Mbytes (1 Mbyte = 1048576 bytes)
Verifying drive integrity, 14% Complete.
Type “N” then press Enter key6
Create Primary DOS Partition
Current fixed disk drive : 1
Total disk space is 19571 Mbytes (1 Mbyte= 1048576 bytes)
Maximum space available for partition is 19571 Mbytes (100%)
Enter partition size in Mbytes or percent of disk space (%) to
create a Primary DOS Partition……………………………………………………[19571]
Press Esc to return to FDISK Options
Check to drive
Create Primary DOS Partition
Current fixed disk drive : 1
Do you wish to use the maximum available size for a Primary DOS Partition
(Y/N)………………………………………………………………….? [N]
Press Esc to return to FDISK Options
This is to create “Primary DOS partition”
Type “2048” then press Enter key7
Create Primary DOS Partition
Current fixed disk drive : 1
Partition Status Type Volume Label Mbytes System Usage
C: 1 PRI DOS 2048 UNKNOWN 10%
Primary DOS Partition created, drive letters changed or added
Press Esc to Continue
Press Enter key9
Press Esc key8
Create Primary DOS Partition
Current fixed disk drive : 1
Total disk space is 19571 Mbytes (1 Mbyte= 1048576 bytes)
Maximum space available for partition is 19571 Mbytes (100%)
Enter partition size in Mbytes or percent of disk space (%) to
create a Primary DOS Partition……………………………………………………[2048]
Press Esc to return to FDISK Options
Microsoft Windows 98
Fixed Disk Setup Program
(C) Copyright Microsoft Corp. 1983 – 1998
FDISK Options
Current fixed disk drive : 1
Choose one of the following:
1. Create DOS partition or Logical DOS Drive
2. Set active partition
3. Delete partition or Logical DOS Drive
4. Display partition information
5. Change current fixed disk drive
Enter choice : [1]
Press Esc to exit FDISK
Type “2” then press Enter key10
Create Extended DOS Partition
Current fixed disk drive : 1
Partition Status Type Volume Label Mbytes System Usage
C: 1 PRI DOS 2048 UNKNOWN 10%
Verifying drive integrity, 19% Complete.
Create Extended DOS Partition
Current fixed disk drive : 1
Partition Status Type Volume Label Mbytes System Usage
C: 1 PRI DOS 2048 UNKNOWN 10%
Total disk space is 19571 Mbytes (1 Mbyte= 1048576 bytes)
Maximum space available for partition is 17524 Mbytes (90%)
Enter partition size in Mbytes or percent of space (%) to
create an Extended DOS Partition.………………………………………………[17524]
Press Esc to return to FDISK Options.
This step is to Create “Extended DOS partition” Press Enter key
Check to drive
11
Create DOS Partition or Logical DOS Drive
Current fixed disk drive : 1
Choose one of the following :
1. Create Primary DOS Partition
2. Create Extended DOS Partition
3. Create Logical DOS Drive(s) in the Extended DOS Partition
Enter choice : [2]
Press Esc to return to FDISK Options
Press Esc key
Create Extended DOS Partition
Current fixed disk drive : 1
Partition Status Type Volume Label Mbytes System Usage
C: 1 PRI DOS 2048 UNKNOWN 10%
EXT DOS 17524 UMKNOWN 90%
Extended DOS Partition created.
Press Esc to Continue
Created Logical DOS Drive(s) in the Extended DOS Partition
No logical drives defined
Verifying drive integrity, 25% Complete.
Created Logical DOS Drive(s) in the Extended DOS Partition
No logical drives defined
Total Extended DOS Partition size is 17524 Mbytes (1 Mbyte= 1048576 bytes)
Maximum space available for logical drive is 17524 Mbytes (100%)
Enter logical drive size in Mbytes or percent of disk space (%).………………[17524]
Logical DOS Drive created, drive letters changed or added
Press Esc to return to FDISK Options
12
Check to drive
This is to create “Logical DOS drive(s)” in the “Extended DOS partition”
Created Logical DOS Drive(s) in the Extended DOS Partition
Drv Volume Label Mbytes System Usage
D: 17524 UNKNOWN 100%
All available space in the Extended DOS Partition
is assigned to logical drives.
Press Esc to continue
13Type “17524” or “100%”, then press Enter key
Created Logical DOS Drive(s) in the Extended DOS Partition
No logical drives defined
Total Extended DOS Partition size is 17524 Mbytes (1 Mbyte= 1048576 bytes)
Maximum space available for logical drive is 17524 Mbytes (100%)
Enter logical drive size in Mbytes or percent of disk space (%).………………[17524]
Press Esc to return to FDISK Options
D: Drive is created in the “Extended DOS partition”, then press ESC key
14
Microsoft Windows 98
Fixed Disk Setup Program
(C) Copyright Microsoft Corp. 1983 – 1998
FDISK Options
Current fixed disk drive : 1
Choose one of the following:
1. Create DOS partition or Logical DOS Drive
2. Set active partition
3. Delete partition or Logical DOS Drive
4. Display partition information
5. Change current fixed disk drive
Enter choice : [5]
Press Esc to exit FDISK
When you try to install more than two HDD, Type "5" and press "enter" since you have to change the current drive.
Display Partition Information
Disk Drv Mbytes Free Usage
1 19571 100%
C: 2048
D: 17524
2 19571 19571 %
(1 MB= 1048576 bytes)
Enter Fixed Disk Drive Number (1-2)…………………………………[2]
Press Esc to return to FDISK Option
Type “2” , then press Enter key15
Check “Change current fixed disk drive” are created normally.
Microsoft Windows 98
Fixed Disk Setup Program
(C) Copyright Microsoft Corp. 1983 – 1998
FDISK Options
Current fixed disk drive : 2
Choose one of the following:
1. Create DOS partition or Logical DOS Drive
2. Set active partition
3. Delete partition or Logical DOS Drive
4. Display partition information
5. Change current fixed disk drive
Enter choice : [1]
Press Esc to exit FDISK
16
Should be created Dos partition is Logical Dos drive, so press Enter key
Microsoft Windows 98
Fixed Disk Setup Program
(C) Copyright Microsoft Corp. 1983 – 1998
FDISK Options
Current fixed disk drive : 2
Choose one of the following:
1. Create DOS partition or Logical DOS Drive
2. Set active partition
3. Delete partition or Logical DOS Drive
4. Display partition information
5. Change current fixed disk drive
Enter choice : [1]
Press Esc to exit FDISK
17
Type “2” then press Enter key18
Create Extended DOS Partition
Current fixed disk drive : 2
Verifying drive integrity, 19% Complete.
Check to drive
Create DOS Partition or Logical DOS Drive
Current fixed disk drive : 1
Choose one of the following :
1. Create Primary DOS Partition
2. Create Extended DOS Partition
3. Create Logical DOS Drive(s) in the Extended DOS Partition
Enter choice : [2]
Press Esc to return to FDISK Options
Create Extended DOS Partition
Current fixed disk drive : 2
Total disk space is 19571 Mbytes (1 Mbyte= 1048576 bytes)
Maximum space available for partition is 19563 Mbytes (100%)
Enter partition size in Mbytes or percent of space (%) to
create an Extended DOS Partition.………………………………………………[19563]
Press Esc to return to FDISK Options.
This step is to Create “Extended DOS partition” Press Enter key19
Press Esc key
Create Extended DOS Partition
Current fixed disk drive : 2
Partition Status Type Volume Label Mbytes System Usage
1 EXT DOS 17524 UMKNOWN 100%
Extended DOS Partition created.
Press Esc to Continue
20
Created Logical DOS Drive(s) in the Extended DOS Partition
No logical drives defined
Verifying drive integrity, 25% Complete.
Check to drive
Created Logical DOS Drive(s) in the Extended DOS Partition
No logical drives defined
Total Extended DOS Partition size is 19563 Mbytes (1 Mbyte= 1048576 bytes)
Maximum space available for logical drive is 19563 Mbytes (100%)
Enter logical drive size in Mbytes or percent of disk space (%).………………[19563]
Logical DOS Drive created, drive letters changed or added
Press Esc to return to FDISK Options
This is to create “Logical DOS drive(s)” in the “Extended DOS partition”
Created Logical DOS Drive(s) in the Extended DOS Partition
Drv Volume Label Mbytes System Usage
D: 19563 UNKNOWN 100%
All available space in the Extended DOS Partition
is assigned to logical drives.
Press Esc to continue
21Type “19563” or “100%”, then press Enter key
Created Logical DOS Drive(s) in the Extended DOS Partition
No logical drives defined
Total Extended DOS Partition size is 19563 Mbytes (1 Mbyte= 1048576 bytes)
Maximum space available for logical drive is 19563 Mbytes (100%)
Enter logical drive size in Mbytes or percent of disk space (%).………………[19563]
Press Esc to return to FDISK Options
D: Drive is created in the “Extended DOS partition”, then press ESC key
Press Esc to return to FDISK Options
14If you have two HDD to add, repeat the same way from item to item 21
Type “4” , then press Enter key
22 Top menu is displayed, Check “Primary DOS Drive(s)” and “Extended DOS Drive” are created normally.
23
Microsoft Windows 98
Fixed Disk Setup Program
(C) Copyright Microsoft Corp. 1983 – 1998
FDISK Options
Current fixed disk drive : 1
Choose one of the following:
1. Create DOS partition or Logical DOS Drive
2. Set active partition
3. Delete partition or Logical DOS Drive
4. Display partition information
5. Change current fixed disk drive
Enter choice : [1]
Press Esc to exit FDISK
Microsoft Windows 98
Fixed Disk Setup Program
(C) Copyright Microsoft Corp. 1983 – 1998
FDISK Options
Current fixed disk drive : 1
Choose one of the following:
1. Create DOS partition or Logical DOS Drive
2. Set active partition
3. Delete partition or Logical DOS Drive
4. Display partition information
5. Change current fixed disk drive
Enter choice : [4]
Press Esc to exit FDISK
Display Partition Information
Drv Volume Label Mbytes System Usage
D: 17524 UNKNOWN 100%
Total Extended DOS Partition size is 17524 Mbytes (1 Mbyte = 1048576 bytes)
Press Esc to continue
Display Partition Information
Current fixed disk drvie : 1
Partition Status Type Volume Label Mbytes System Usage
C: 1 PRI DOS 2048 UNKNOWN 10%
2 EXT DOS 17524 UMKNOWN 90%
Total disk space is 12417 Mbytes ( 1 Mbyte = 1048576 bytes)
The Extended DOS Partition contains Logical DOS Drivers.
Do you want to display the logical drive information (Y/N)………..…….?[Y]
Press Esc to return to FDISK option
24 Type “Y”, press Enter key
Press Esc key25
26
Top menu is displayed
To boot normally “ Active partition must be set. Type “2”, Press Enter key
Microsoft Windows 98
Fixed Disk Setup Program
(C) Copyright Microsoft Corp. 1983 – 1998
FDISK Options
Current fixed disk drive : 1
Choose one of the following:
1. Create DOS partition or Logical DOS Drive
2. Set active partition
3. Delete partition or Logical DOS Drive
4. Display partition information
5. Change current fixed disk drive
Enter choice : [1]
Press Esc to exit FDISK
Microsoft Windows 98
Fixed Disk Setup Program
(C) Copyright Microsoft Corp. 1983 – 1998
FDISK Options
Current fixed disk drive : 1
Choose one of the following:
1. Create DOS partition or Logical DOS Drive
2. Set active partition
3. Delete partition or Logical DOS Drive
4. Display partition information
5. Change current fixed disk drive
Enter choice : [2]
Press Esc to exit FDISK
Sat Active Partition
Current fixed disk drive : 1
Partition Status Type Volume Label Mbytes System Usage
C: 1 PRI DOS 2048 UNKNOWN 10%
2 EXT DOS 17524 UMKNOWN 90%
Total disk space is 19571 Mbytes ( 1 Mbyte = 1048576 bytes)
Enter the number of the partition you want to make active…..……………...[ ]
Press Esc to return to FDISK Options
27
“Active partition” menu is displayer
Type 1, press Enter key
Sat Active Partition
Current fixed disk drive : 1
Partition Status Type Volume Label Mbytes System Usage
C: 1 A PRI DOS 2048 UNKNOWN 10%
2 EXT DOS 17524 UMKNOWN 90%
Total disk space is 19571 Mbytes ( 1 Mbyte = 1048576 bytes)
Partition 1 made active
Press Esc to continue
“Active partition: is completed. Press Enter key28
Sat Active Partition
Current fixed disk drive : 1
Partition Status Type Volume Label Mbytes System Usage
C: 1 PRI DOS 2048 UNKNOWN 10%
2 EXT DOS 17524 UMKNOWN 90%
Total disk space is 19571 Mbytes ( 1 Mbyte = 1048576 bytes)
Enter the number of the partition you want to make active…..……………...[ 1 ]
Press Esc to return to FDISK Options
You MUST restart your system for your changes to take effect.
Any drives you have created or changed must be formatted
AFTER you restart.
shut down Windows before restarting.
Press Esc to exit FDISK
30
29
FDISK is completed.
Microsoft(R) Windows 98
(C) Copyright Microsoft Corp 1981-1999
A:\>
Dos mode is displayed . You must restart your system.
Press Ctrl + Alt + Del key, or turn off power.
31
Microsoft Windows 98
Fixed Disk Setup Program
(C) Copyright Microsoft Corp. 1983 – 1998
FDISK Options
Current fixed disk drive : 1
Choose one of the following:
1. Create DOS partition or Logical DOS Drive
2. Set active partition
3. Delete partition or Logical DOS Drive
4. Display partition information
5. Change current fixed disk drive
Enter choice : [2]
Press Esc to exit FDISK
Top menu is displayed. Press Esc key
Booting by A: Drive
A:\>
All the Drive must be formatted to use HDD.
Type “format C:”, then press Enter key.
Type “Y”, then press Enter key
Microsoft(R) Windows 98
(C) Copyright Microsoft Corp 1981-1999
A:\>FORMAT C:
A:\>FORMAT C:
WARNING, ALL DATA ON NON-REMOVABLE DISK
DRIVE C : WILL BE LOST!
Proceed with Format (Y/N) ? Y
32
33
A:\>FORMAT C:
WARNING, ALL DATA ON NON-REMOVABLE DISK
DRIVE C : WILL BE LOST!
Proceed with Format (Y/N) ? Y
Formatting 1,027.56M
Format complete.
Writing out file allocation table
Complete.
Calculating free space (this may take several minutes)…
Complete.
Volume label (11 characters, ENTER for none) ?
Press Y key
A:\>FORMAT C:
WARNING, ALL DATA ON NON-REMOVABLE DISK
DRIVE C : WILL BE LOST!
Proceed with Format (Y/N) ? Y
Formatting 1,027.56M
20 percent completed
34
Press Enter key.35
A:\>FORMAT C: /S
WARNING, ALL DATA ON NON-REMOVABLE DISK
DRIVE C : WILL BE LOST!
Proceed with Format (Y/N) ? Y
Formatting 2048M
Format complete.
Writing out file allocation table
Complete.
Calculating free space (this may take several minutes)…
Complete.
Volume label (11 characters, ENTER for none) ?
2,049,359,744 bytes total disk space
411,136 bytes used by system
2,049,359,744 bytes available on disk
4,096 bytes in each allocation unit.
262,538 allocation units available on disk.
Volume Serial Number is 4225-16F2
A:\>
Format rest drive(D:, E:, F:, G:…) as same way
EX)
A:\>FORMAT D:
A:\>FORMAT E:
A:\>FORMAT F:
A:\>FORMAT G:
36
Display DOS prompt mode.