· 2.02 standard entrances specifications general description furnish all necessary materials,...
TRANSCRIPT
2.02 Standard Entrances Specifications
General
Description Furnish all necessary materials, labor and
equipment for the complete installation of aluminum entrance doors, door frames and hardware as shown on the drawings and specified herein.
Doors and frames shall be as manufactured by Tubelite Inc., Reed City, Michigan. W,henever substitute products are to be considered, supporting technical literature, samples, drawings and performance data must be submitted ten (10) days prior to bid in order to make a valid comparison of the products involved.
Test reports certified by an independent laboratory must be made available upon request.
Products
Materials Extrusions shall be of aluminum alloy
6063-T5 extruded within commercial tolerance and free from defects impairing strength and/or durability. Door stile and rail sections to be a minimum of ,125 inch wall thinkness. Door frame sections to be of .080 inch minimum wall thickness, with glazing and door moldings a minimum of .050 inch.
Steel tension rods of ,375 inch diameter shall run the full width of the top and bottom rails and shall be fixed with steel plates and lock nuts.
Door glazing shall be by means of an interior and exterior fixed gasket of high quality extruded elastomeric material. Door frame members shall have a continuous wool pile weatherstripping at the head and jamb members. Bottom rail weather- sweep at threshold optional (architect specify). Door stops shall be of snap-in design on butt hinge and offset pivot applications, eliminating use of exposed screws.
All door and frame members shall be accurate1
All H fitted to flush hairline joints,
tack (Narrow Stile) Doors shall have an adjustable setting block in the top rail. Hardware
Stock Entrance Doors and Frames shall have standard hardware as furnished by Tubelite”, as follows:
Butt Hinges P-092 P-1565 P-1564 E-001 9 P-l 420 P-1409 P-l 408 P-l 438
Ball Bearing Butt Hinges Push Bar Pull Handle %” x 4” Threshold Deadbolt MS Lock Lock Faceplate, or Lock Faceplate (Pairs of Doors) TubeliteiLCN Surface Mount Closer
P-059 Flush Bolts (Pairs of Doors)
Offset Pivots P-694 Top and Bottom Pivots P-1565 Push Bar P-1564 Pull Handle E-0019 %” x 4” Threshold P-1420 Deadbolt MS Lock P-1409 Lock Faceplate, or P-1408 Lock Faceplate (Pairs of Doors) P-1438 Tubelite/LCN Surface Mount
Closer P-059 Flush Bolts (Pairs of Doors)
Center Pivots P-970 Concealed Overhead Closer with
Bottom Pivot P-1565 Push Bars E-001 9 %” x 4” Threshold P-1420 Deadbolt MS Lock P-1409 Lock Faceplate, or P-1408 Lock Faceplate (Pairs of Doors) P-059 Flush Bolts (Pairs of Doors)
Special hardware for custom doors and entrances shall be specified by the architect. Hardware furnished by others shall be sent to the door manufacturer for application. Finish
All exposed framing surfaces shall be free of scratches and other serious blemishes.
Finish to be: (architect select) Etched and clear anodized (AA-M12C22A31) -
Clear (OA) Electrolytically deposited color (AA-M 12C22A44) -
Champa ne (4K) i3 Light Am er (2K)
Amber (1 K) Statuary Bronze (3K) Black (OD)
Fluoropolymer painted color
Execution
Installation Shall be in accordance with the manufac-
turer’s installation instructions and the approved shop drawings.
Note: In keeping with Tubelite’s policy of continuing
product improvements, all specifications are subject to change without written notice by the manufacturer.
TUBELITE’ SxxILm L ENIMKIS 1998
2.03Standard Entrances
Key Elevation & 1/4 Size Details
1999
6
TRANSOMOPENING
1 3/4"
6a
TRANSOMOPENING
1 3/4"
1a
1 3/4" DOOR OPENING
7
8
1 3/4"
OPENING DIMENSION
DOOR OPENING1 3/4"
1
5a
DO
OR
OP
EN
ING
TR
AN
SO
MO
PE
NIN
G1
3/4"
3a
DO
OR
OP
EN
ING 4 1/2"
3b
DO
OR
OP
EN
ING
2a1 3/
4"1/
4"
3
OP
EN
ING
DIM
EN
SIO
N
DO
OR
OP
EN
ING
4
5
TR
AN
SO
MO
PE
NIN
G1
3/4"
1 3/
4"1/
4"
10"
1 3/
4"1/
4"
2
4
1 3/
4"1/
4"
KEY ELEVATIONS
1
2
3
5
46
1 78
BA
2.05 Standard Entrances
Isometric Details E-4015
F;:973 E-4i20
E-4545
B
Right Hand
C
, E-4531
E-4543 E-4545
C
E-0019
NOTE: Double acting doors are not handed.
TUBELITE 1998 ~~~..~R~NI~~LMI(I*I(I~
2.06Standard EntrancesJamb-Offset Pivot or Butt Hinge
1999
1/2"
3/16
"
13/16"
9/16
"
1/4"
2 1/8"
1/16"HINGESIDE
1 3/4"
Center ofPivot
3/4"
BA
CK
ER
RO
D
E0437
P1431
1/4" GLASS
E0410
E4531
P1098 A
E0055
E4543OPTIONAL
AN
CH
OR
S N
.B.T
. S
EA
LAN
T
P1713(E4542)
DOOR OPENING
E4544 CAD DETAIL FILE NO.090DRJBH
SINGLE DOORS
3'-0" X 7'-0"
3'-6" x 7'-0"
STANDARD SIZES
DOUBLE DOORS
5'-0" X 7'-0"
6'-0" x 7'-0"1
2.07Standard Entrances
Jamb-Offset Pivot or Butt Hinge
1999
8
1/8" LOCKSIDE
1 3/4"
BA
CK
ER
RO
D
2"
E0437
P1431
1/4" GLASS
E0410
E4531
P1098 A
E0055
2 1/8"
E4543OPTIONAL
AN
CH
OR
S N
.B.T
. S
EA
LAN
T
3/16
"
(E4542)P1713
DOOR OPENING
E4544CAD DETAIL FILE NO.
090DRJBL
SINGLE DOORS
3'-0" X 7'-0"
3'-6" x 7'-0"
STANDARD SIZES
DOUBLE DOORS
5'-0" X 7'-0"
6'-0" x 7'-0"
2.08Standard EntrancesHead-Offset Pivot or Butt Hinge
1999
1/2"
2 1/
8"
1/8"
1 3/
4"
DO
OR
OP
EN
ING
P1431
2"
E4531
E45124
BACKER ROD
E0410E0437
E1375
SEALANT ANCHORS N.B.T.
P1098 A
FR
AM
E O
PE
NIN
G
CAD DETAIL FILE NO.090DRTR2
2.09Standard Entrances
Bottom Rail-Offset Pivot or Butt Hinge
1999
CAD DETAIL FILE NO.090DRBR 3
E0410
P1431 (EA. SIDE)
FR
AM
E H
EIG
HT
DO
OR
OP
EN
ING
E1376
FLOOR LINE
E0019
CLOF
PIVOT
4"
3/16
"
1/2"11/16"
3/4"
4 1/2"
TIE ROD
1/4" GLASS
SETTINGBLOCKS
E0437
2.15Standard Entrances
Transom Bar and Head-Offset Pivot or Butt Hinge
1999
CAD DETAIL FILE NO.160HEAD
4
CAD DETAIL FILE NO.090TRAN 5
E45124
DO
OR
OP
EN
ING
P1431
TR
AN
SO
M O
PE
NIN
G
E4543
2 1/
8" P1098A E4531
E1375
E0437
E0410
1 3/
4"
1/8"
SEE GLAZING CHART(PG. 2.13)
SEE BLOCK CHART
E4015 E4026
SEALANT
BACKER ROD
E-4541
2"
1 3/
4"
ANCHORS N.B.T.
2.17Standard Entrances
Door Stiles
1999
CAD DETAIL FILE NO.090STILE
2-1/8"
2-1/8"5"
5"
4"
4"
HINGE OR LOCK STILE
(CENTER HUNG)
HINGE OR LOCK STILE(BUTT HINGES OR OFFSET PIVOTS)
MEETING STILES
5"
4"
2-1/8"
HINGE OR LOCK STILE(BUTT HINGES OR OFFSET PIVOTS)
HINGE OR LOCK STILE(CENTER HUNG)
2-1/8" STILE - E00554" STILE - E00865" STILE - E0416
2-1/8" STILE - E00574" STILE - E00885" STILE - E0418
MEETING STILES
E0055
2-1/8" STILE - E00564" STILE - E00875" STILE - E0417
2-1/8" STILE - E00574" STILE - E00885" STILE - E0418
E0057
E0057E0056
PILEWEATHERINGP013D
PILEWEATHERINGP013D
7
2.18Standard EntrancesTop and Bottom Rails
2001
E30166"
E266910"
E26827 1/2"
E04196 1/2"
E03185"
E01404 1/2"
E00544"
E13764"
E01483"
E02552 1/8"
E13752 1/8"
DETAIL SCALE:1/4"=1'
SCALE: FULL
*TYPICAL POCKET DEPTH IS1 9/16" EXCEPT THE FOLLOWING.E0148 = 1 1/2"E1375 = 1/4"E1376 = 3/8"E0255 = 7/8"
ALL RAILS CAN BE USEDAS A TOP OR BOTTOM RAIL.
E3021MAY BE USED WITH ANYCOMBINATION OFBOTTOM RAILS FORDESIRED HEIGHT.
HE
IGH
T O
F R
AIL
,SH
OW
N IN
EA
CH
PA
RT
BOTTOM RAILS
TOP RAILS
1 3/4"
1/8"
1 9/
16"
2.21Standard Entrances
Adjustable Astragal Option
1999
5"
4"
2 1/
8"E-0417
E0087
E0056
E-2851
E2671
E1204
P938(2)
E1195
1 3/4"
2 1/
8"2
1/8"
4"4"
E2671
E0056
E1204
E0087
5"5"
1/8"
E2851
E0417
CAD DETAIL FILE NO.ADJASTR2
CAD DETAIL FILE NO.ADJASTR1 W/E1193
Finish Floor Line with or without threshold
Push Bar
PullHandle
2.25Standard Entrances
Hardware Locations
Notes:
If panics are required in lieuof push bars, see Sec. 2Pg. 24 for panic location.
Vertical butt dimensions arefor Tubelite standard 4- "mortised butt. Dimensionsfrom top (3- ") andbottom (3- ") remainthe same if butt size and/ordoor opening changes.
1/2
1/1611/16
Note:On custom door opening heights, the bottom dimensions of 3- "and top dimensions of 3- " are constant. Intermediate dimensionsof 68- " and 31- " will vary accordingly. Dimensions of 39- " and36" are constant.
11/161/16
1/4 7/8 1/2
dr.elev.cdr
STOREFRONT, CURTAINWALL& ENTRANCE SYSTEMS